nylon slings steel chokers also available upon request · nylon slings steel chokers also available...
TRANSCRIPT
25
NYLON SLINGS Steel Chokers also available upon request Common types available are listed below. Other unique types and sizes may be available- call the shop to inquire. Selection of slings:
1. Select Type: Endless (EN) or Eyes on each End (EE)
2. Select Length and Width ( Most slings at Staff are 2” width) additional widths available per special request. 2” x 3’ long 2” x 10’ long 2” x 18’ long 2” x 4’ long 2” x 12’ long 2” x 20’ long 2” x 6’ long 2” x 14’ long 2” x 8’ long 2” x 16’ long
3. Select Capacity: Note that One ply and Two ply slings are available. Capacity is also dependent on how it is used in
lifting. Liftall Slings
Rated Capacities in Lbs Vertical Choker V. Basket Part # Eyes each End (EE) One ply (2” width) 3,200 1,250 6,400 EE1-802 Two ply (2” width) 6,400 5,000 12,800 EE2-802 Endless (EN) One ply (2” width) 6,400 5,000 12,800 EN1-802 Two ply (2” width) 12,200 9,800 24,400 EN2-802
Wear Flex Slings
Rated Capacities in Lbs Vertical
@ 90º Choker @30º
V. Basket @90º
Part #
Eyes each End (EE) One ply (2” width) 3100 2480 6200 EE1-0902SE Two ply (2” width) 6200 4960 12,400 EE2-0902SE Endless (EN) One ply (2” width) 6200 4960 12,400 EN1-0902SE Two ply (2” width) 12,500 10,000 25,000 EN2-0902SE
28
SECTION 1 WIRE PULLING - FEEDERS
CABLE PULLING LUBRICATION SYSTEM
GREENLEE ULTRA GLIDER (UG5) DESCRIPTION
• 2” – 4” (2”, 2 ½”, 3”, 3 ½”, 4”) diameter slip in applicators • 2” – 4” diameter threaded applicators for upward feeds • Additional applicators available: ¾”, 1”, 1-1/4”, 1-1/2” threaded • Additional applicators available: 1-1/2”, 5”, 6” slip-in • Three pump speeds to match pulling speed • 10 foot hose- 20 ft hose optional
ADVANTAGES / BENEFITS
• More efficient pull – coats wire evenly • Reduce amount of lube by 20% • Reduce pulling force – less likely for a failure in systems, rope break, wire grips pull off • Reduce pulling force – reduces wear and tear on puller • Reduce slip and fall or mess on floor • Positions worker further away from pinch point where wire enters conduit. Especially important for
vertical feeds from bottom • Works well in limited space areas – can apply lube at elevations on scissors lift. • Great for lubing underground PVC.
COST JUSTIFICATION
• Labor savings – For some applications, 1 person can lube and feed wire into conduit instead of two people. Estimated labor savings of $90 per pull.
• Saves on lube used and wear on puller equipment • Pays for itself after 30 pulls
29
SECTION 1
WIRE PULLING - FEEDERS
MAXIS SAFETY TRIGGERS (TR01) DESCRIPTION
• Foot switches (Dead man switch) for both cable puller and feeder operation
• Master switch plugs into cable puller • Remote switch at feeder uses RF technology to communicate
with master switch • Both foot switches must be energized for the puller to operate.
Any time either foot pedal is released, the puller stops. • Will communicate up to 1,500 ft between walls and 1.5 miles line of sight • Equipped with digital meter indicating pounds of force during pull • Works with Greenlee wire puller
ADVANTAGES / BENEFITS
• Reduce / eliminate radio miscommunication. Particularly useful in areas with poor radio reception • Person feeding wire can also stop pull to reduce hazards of hands caught in wire or pipe • Reduce risk of wire feeding mishaps that can damage cable
Contact the Safety Director for this specialty safety device.
30
SECTION 2 WIRE CARTS – BRANCH CIRCUITS
GREENLEE WIRE DISPENSER #910 DESCRIPTION
• Base has 2 fixed and 2 swivel locking heavy duty casters. • The spool rack consists of 10 spindles and an adjustable guide loop,
and can be turned 360°independent of the base. • Spindles are angled to contain reels and act as a brake while
paying out wire. • Fits through a 36" (915 mm) opening. • Capacity: 10 spools up to 18” in diameter. • Weight: 213 lbs
GREENLEE WIRE CART #911 DESCRIPTION
• Large capacity, excellent for storing, transporting or feeding wire. • Save space, use and store vertically or horizontally. • 5 strong reel axles with spring clip retainers plus 2 positions for axle storage
allows you to configure for large reels with no loose parts. • Rugged 8" wheels. • Built-in wire guide for horizontal dispensing. • Will pass through a 28" (711.2 mm) opening. • Capacity: Six 2,500’ spools up to 16” Dia. • Fifteen 500’ spolls up to 8” Dia. • Weight: 62 lbs
GREENLEE 10-REEL CADDY #9516 DESCRIPTION
• Holds up to ten 2,500' (767 m) spools of 10 gauge wire. • Folds down for easy storage. • 2 fixed and 2 locking swivel casters for easy portability. • Pinless design eliminates loose parts. • Maximum Spool Diameter: 15” • Maximum Spool Width: 14.63” • Weight: 98 lbs
31
SECTION 2 WIRE CARTS – BRANCH CIRCUITS
GREENLEE CABLE REEL TRANSPORTER #916 DESCRIPTION
• Handle folds to save space when using as a dispenser. • Size: 63” long x 297/8” wide x 26 ¾” High • Capacity: Reels of cable or BX up to 20” W and 40” in dia. • Maximum Total Reel Weight: 300 lbs • Weight : 110 lbs
GREENLEE BX-ARMORED COILED CABLE DISPENSER & TRANSPORTER #37202 DESCRIPTION
• Dispense one coil of armored cable, flexible conduit, Greenfield or NM-B cable • Without twists or tangles • Base with adjustable tension control rotates to dispense cable • Large pulling eye rotates freely • Transport up to 3 coils • Capacity: one 250’ coil of 14/2, 14/3, 12/2, 12/3 armored cable or romex. • Weight: 45 lbs
GREENLEE WIRE REEL SUPPORT FRAME #914 DESCRIPTION
• Insert spindle in one 914 support frame, tighten locking screw, slide reels on spindle, insert spindle in second support frame, tighten thumb screw and you’re ready to go.
• Capacity: 1” rigid conduit for spindle holds 500’ to 2500’ spools up to 18” in diameter.
GREENLEE AND CADDY #9502 DESCRIPTION
• Holds four 500’ spools of #10 AWG • Holds eight 500’ spools of #12 AWG • Maximum Spool Diameter: 9” • Maximum Spool Width: 10.5”
32
SECTION 3 BENDING PIPE
GREENLEE TABLE BENDER 881 DESCRIPTION
• 2 ½ - 4” EMT, IMC and Rigid • Bends a 90º elbow in 4” rigid in 95 seconds
ADVANTAGES
• Fast and easy setup. • Works great for large projects
DISADVANTAGES
• Need plenty of floor space
EEGOR BENDER WITH TABLE DESCRIPTION
• Bends 2 ½” to 4” EMT, IMC and Rigid • Hydraulic pivot jack adjusts table to
horizontal and vertical positions
ADVANTAGES • Allows multiple bends put close together on same length of pipe
MINI EEGOR BENDER DESCRIPTION
• 1-2” EMT, IMC and Rigid
ADVANTAGES
• Mobility- great for small projects HYDRAULIC TW BENDER- HAND PUMP DESCRIPTION
• Use for EMT only 1.25” -2” ADVANTAGES
• Mobility- great for small projects • No Electrical power needed
33
SECTION 3 BENDING PIPE
ENERPAC GB CYCLONE BENDER B2000 DESCRIPTION
• ½ - 2” EMT, IMC and Rigid • Ability to make repeated bends at same degree • Horizontal and vertical positions allow unit to
create accurate offset bends
ADVANTAGES • Mobility- 4 wheels
GREENLEE 555 & & 853 & 855 DESCRIPTION
• ½ - 2” EMT, IMC and Rigid
ADVANTAGES
• Excellent mobility GREENLEE ONE SHOT 884 & 885 DESCRIPTION
• 1 ¼ -4” rigid conduit bender • Bends one shot 90ºs • The 885 bends 5”.
GREENLEE RACHET BENDER 1818 DESCRIPTION
• ¾” – 2” EMT, ½” – 1¼”, IMC ½”-1½” Rigid • Bypass ratchet for fast direct bending on smaller sizes
ADVANTAGES
• Easy to move • Good for projects when power is not available
34
SECTION 4 THREADING PIPE AND VISES
RIGID THREADING MACHINE #1224, 1215 (Tabletop) DESCRIPTION
• Threads ¼” -2” pipe at 36 RPM and 2 ½” – 4” at 12 RPM • Threads a wide range of pipe including black, galvanized and
PVC pipe, together with stainless steel, IMC and heavy wall conduit.
ADVANTAGES • Great for large projects • Portable
DISADVANTAGES
• Difficult to thread on bent piece of pipe •
RIGID #300 DESCRIPTION
• ½” – 2” Pipe, 2 ¼ - 4” with 141 and 4-6” with 161 geared threaders • ½ HP • Foot switch and stand
ADVANTAGES • Speed of cutting
DISADVANTAGES
• Not portable RIGID 600 & TOLEDO PORTA-PONY THREADING MACHINE DESCRIPTION
• ¼” – 1¼” Pipe. • 32 RPM at no load
ADVANTAGES
• Hand held and portable RIGID STOCK & DIE DESCRIPTION
• 2.5” – 4” Pipe. • Also 5” - 6” available • Threaded hub • Use portapony drive when have a bend
DON’T FORGET TO ORDER THE OLIER (#318) AND CUTTING OIL
35
THREE LEGGED VISE DESCRIPTION
• Chain and clamp styles
PIPE SUPPORT/STAND WORKBENCH WITH 5” OR 6” VISE
36
SECTION 5 CUTTING PIPE
FLOOR BAND SAW
ADVANTAGES
• Great for big projects CIRCULAR SAW (BATTERY) – PANASONIC EY3530, EY4542 DESCRIPTION
• 15.6 Volt with 3.0Ah Ni-MH battery- fully charged in 45 minutes • 1/8 to 113/16” cut depth • Electric brake and shaft lock adjustment for blade replacement
DISADVANTAGES
• Noisy tool • Limitations with larger pipe and unistrut
PORTA BAND – (BATTERY) Stout STX-250 DESCRIPTION
• Cuts up to 2.5” • Use 18V NiCd battery
ADVANTAGES
• Works for larger pipe and unistrut PORTA BAND- (ELECTRIC) Milwaukee Electric & Porter Cable DESCRIPTION
• Normal cut (6225) and deep cut (6230) options for Milwaukee Electric models
RIGID RATCHET REAMER DESCRIPTION
• ½” – 2” • Self Feeding spiral design for extra fast and easy hand reaming
37
SECTION 6 INSTALLING & FASTENING PIPE
HILTI GAS OPERATED FASTENING TOOL -GX 120 DESCRIPTION
• Drives 750 fasteners with single can of gas • Magazine holds 40 fasteners • LED gas gauge helps you avoid running out of gas • Quieter than powder actuated tool
ADVANTAGES • No training certification required • Faster, lighter weight, less noisy • Use Hilti straps and washers with this tool
DISADVANTAGES
• Can’t get to hard to reach areas HILTI POWDERED ACTUATED – DX350, DX351, DX451, DX460 DESCRIPTION
• Fastens up to 700 nails per hour- increased productivity • Easy drop in magazine for one-handed operation • Light weight and low recoil • Booster power regulator for accurate nail driving
ADVANTAGES
• Extension Pole tool available for overhead work DISADVANTAGES
• Requires certification FASTENAL SETTING TOOL DESCRIPTION
• Tool for setting concrete anchors with a hammer drill instead of by hand with a hammer. • Fastenal Part # 10095452
ADVANTAGES: Reduce stress on shoulder from awkward hammering positions. HAMMERDRILL WITH DUST COLLECTION SYSTEM- For example Hilti TE 5/6 DESCRIPTION
• 36 Volt rotary drill • Uses NiCad battery • 3/16” – ¾” drilling range
38
SECTION 6 INSTALLING & FASTENING PIPE
PIPE WRENCHES DESCRIPTION
• SIZES AVAILABLE: • Belt/Strap: assorted lengths- small and large sizes • Chain: 16”, 18”, 36”, 48” • Straight Pipe: 14”, 18”, 24”, 36”, 48”
DRILL PRESSES MAGNETIC DRILL PRESS- Milwaukee #4203 DESCRIPTION
• 120 Volt, 12.5 amp max • 11 inch drill travel • Adjustable base • Weight – 49 lbs
Drill stands also available- mount a portable hand drill. Floor stand drill presses also available
39
SECTION 7 PIPE STORAGE
GREENLEE CONDUIT AND PIPE STORAGE RACK # 668 DESCRIPTION
• Seven individual bins for storage • Capacity: 1000 lbs • Dimensions: 58 ½” L x 34” W x 63 ½” H • Weight: 113 lbs
LARGE YOKE PIPE CART FOR MASTER BUNDLES
FOUR POSTED CARTS AVAILABLE
40
SECTION 8 TERMINATING FEEDERS
GREENLEE CABLE CUTTER- BATTERY ESC8511 Corded Models available too. DESCRIPTION
• Capacity- 3 3/8” diameter Cu and AL cables • Battery- 12V- 1 hr charge time • Also 120V available • Two speed pump advances the ram quickly to start cut • Blades open automatically when a cut is complete • Cutting head rotates 360º for making cuts in tight locations • Side handles enhances operator control
ADVANTAGES
• Faster than ratchet cutters • Great for tight areas i.e. not enough room for large scissors type cable cutter
IDEAL CABLE CUTTER # 35-078 DESCRIPTION
• Use with battery drill 12V minimum • Cuts up to 750 MCM
ADVANTAGES
• Works with the drill you already have 2 HAND RATCHETT CABLE CUTTER #774 and #45206 DESCRIPTION
• Model 774( 19” handles) – • Use up to 500MCM frequently • Max use 750 MCM
• Model 773 (15” handles) • Use up to 350 MM frequently • Max use 500 MCM
41
SECTION 8 TERMINATING FEEDERS
GREENLEE HYDRAULIC CABLE BENDER #800 DESCRIPTION
• One shot bends up to 90º • 350-1000 MCM • Automatically unloads cable • Compact design bends in tight places • Unit with foot pump keeps both hands free to hold cable
GREENLEE RATCHETT CABLE BENDER #796 DESCRIPTION
• Up through 500 MCM • 10” ratchet extension available
IMPACT WRENCH ( Milw Electric 9082 or Makita 6909D) DESCRIPTION
• 3/8” Sq. drive 1,056 in-lbs torque • 14.4 volt • Weight- 2.4 lbs
ADVANTAGES
• Works great when using self tapping screws into heavy material 12 Ton CRIMPER Greenlee CK124011 –120V Corded or uncorded DESCRIPTION
• Two speed pump to reduce cycle time • Crimping head rotates 360º • Ram automatically retracts when crimp cycle is complete
Burndy Battery (18V) Crimper- PAT750 and 750XT DESCRIPTION
• 12 tons crimping force • Weight 16.5 lbs • Charges in 45 minutes
42
SECTION 8 TERMINATING FEEDERS
HAND HYDRAULIC CRIMPER WITH DIES Burndy Y35 & Y750 DESCRIPTION
• 12 ton crimping force • U shaped dies • Weight: 13 lbs (Y35) and 16 lbs for (Y750)
HAND HYDRAULIC CRIMPER - DIELESS Greenlee 1990 DESCRIPTION
• 15 ton crimping force • Swivel head rotates 180º • Capacity #4 – 1000MCM • Weight 16.5 lbs
Burndy Y644 DESCRIPTION
• 11 ton crimping force • Weight 15 lbs
43
SECTION 9 SPECIALTY LADDERS & SCAFFOLDING
LITTLE GIANT ULTRA STEP STEPLADDER DESCRIPTION
• Adjustable legs • Rated 300 lbs • Can be used on uneven surfaces like stairs and curbs • Fiberglass
FOLDING STEPLADDER (#MT26) DESCRIPTION
• Extension Height: 13’ – 23’ • Stepladder Height 6’-11’ • Storage Height 6’7” • Aluminum – Fiberglass unavailable in this size – • DANGER – Do not use for energized work!
ALUMINUM SCAFFOLD PLANKS WITH GUARDRAILS DESCRIPTION
• Length: 24’ • Width: 20” • Depth: 6” • Rated 500 lbs – 2 person
ALUMINUM EXTENSION PLANK DESCRIPTION
• Rated 250 lbs – 1 person • Opens 8’ – 13’ length • Width: 14”
44
SECTION 9 SPECIALTY LADDERS & SCAFFOLDING
BAKER (ROLLING) SCAFFOLDING DESCRIPTION One Section High
• Platform Height: 6 ft • Overall Height (w/guardrails): 9’6” • Width: 30”
Two Sections High
• Platform Height: 11’6” • Overall Height (w/guardrails): 15’ • Width: 66” (includes outriggers)
Order scaffolding through the shop. Bird Ladder is the preferred vendor for your scaffolding needs.
47
SECTION 10 MOVING HEAVY EQUIPMENT
SWITCHGEAR & TRANSFORMERS
Genie Tinners Lift Genie Superlift Model SL1
• 650 lbs at 18 ft • 500 lbs at 24 ft
Genie Superlift Advantage Model SLA-10
• 11 foot maximum working ht • 1000 lbs at 18” load center • 1000 lbs at 24” load center • 1000 lbs at 32’ load center
Rol – A – Lifts – Model # M10 DESCRIPTION Four lifts available from Milwaukee shop- Tool # 311001 - 311004
• Capacity: 6000 lbs • Width: 24 inches • Lifting height: 6 inches • Wheel Dia: 6 inches
Machinery Rollers DESCRIPTION Rollers available from Milwaukee & Madison shops - Tool # 240001 - 240103
• Capacity: Various sizes starting at 1,500 lbs Machinery Jacks DESCRIPTION Jacks available from Milwaukee & Madison shops - Tool # 246001 - 246012
• Capacity: 5 ton with 10 inch lift • Capacity: 10 ton with 13 inch lift
Johnson Bar Pinch Bars – beveled crowbar
48
SECTION 11 MANUFACTURER’S REPRESENTATIVES
BIRD LADDER Heinz Kahmann 414-702-0368 [email protected] GREENLEE Brent Henke 608-512-5192 [email protected] HILTI Bill O’Sullivan 414-397-9755 [email protected] ELECTROTECH (Wire stripping tools) Tom Banghart 414-333-3046 Cell [email protected] AERIAL LIFTS AERIAL WORK PLATFORMS (AWP) www.awpdelivers.com Russ Wittig 262-246-9300 MILWAUKEE HIGH LIFT Jim Juneau 262-613-2350 [email protected] NES Rentals Jeff Murawski 414-349-9893 [email protected] United Rentals 414-769-1099 unitedrentals.com Adam Forstner 414-234-9615 CONTACT DAVE MUELLER FOR ALL EQUIPMENT RENTAL NEEDS.