operating instructions for fs 345 with fs 101 and cs 300 fs gb

Operating Instructions for FS 345 with FS 101 and CS 300 FS GB

FS 345 Door Controls / Rev.A 0.0 – 1

2 – FS 345 Door Controls / Rev. A 0.0

1. Contents

1. Contents 22. Information in this document 23. General safety instructions 34. Overview of products 45. Commissioning 56. Limit switches 167. Programming with the LCD monitor 188. Navigator (LCD monitor only) 209. Overview of functions 2210. Rechargeable battery and battery charger 3011. Motor brake and auxiliary motor 3412. Technical data 3613. Maintenance 3614. EC Declaration of Incorporation 37

Original operating instructions − Protectedbycopyright.− Nopartoftheseinstructionsmaybereproducedwithout

our prior approval. − Subjecttoalterationsintheinterestoftechnicalprogress.− Alldimensionsaregiveninmillimetres.− Theillustrationsarenottruetoscale.

Meaning of symbols

DANGER!

Safetynoticeindicatingadangerthatwilldirectlyresultindeathorsevereinjury.

WARNING!

Safetynoticeindicatingadangerthatcouldresultindeathorsevereinjury.

CAUTION!

Safetynoticeindicatingadangerthatcanresultinslightormoderateinjuries.

NOTICE

Safetynoticeindicatingadangerthatcanresultindamageto property or in irreparable damage to the product.

CHECK

Reference to a check that needs to be carried out.

REFERENCE

Reference to separate documents that must be observed.

� Instruction requiring action

− List,itemisation

� Reference to other sections of this document

2. Information in this document

GB


3. General safety instructions

DANGER!

Failure to comply with the documentation could result in life-threatening danger!

� Be sure to follow all the safety instructions in this docu-ment.

WarrantyThe function and safety of the equipment is only guaranteed if the warning and safety instructions included in these operat-ing instructions are adhered to.MFZAntriebeGmbH+Co.KGisnotliableforpersonalinjuryor damage to property if these occur as a result of the warn-ings and safety advice being disregarded.MFZ does not accept any liability or warranty for damage due to the use of non-approved spare parts and accessories.

Intended useTheFS345controlisintendedexclusivelyforcontrollingdoorsystems with mechanical limit switches.

Target groupOnlyqualifiedandtrainedelectriciansmayconnect,pro-gramme and service the control.Qualifiedandtrainedelectriciansmustmeetthefollowingrequirements:− Knowledgeofthegeneralandspecificsafetyandaccident

preventionregulations,− Knowledgeoftherelevantelectricalregulations,− Trainingintheuseandcareofappropriatesafetyequip-

ment,− Capableofrecognisingthedangersassociatedwithelec-

tricity.

Instructions regarding installation and connection− ThecontrolisdesignedwithXtypeterminals.− Thecontrolmustbedisconnectedfromtheelectricity

supply before carrying out any electrical work. It must be ensured that the electricity supply remains disconnected for the duration of the work.

− Localprotectiveregulationsmustbecompliedwith.

Information concerning operation− Unauthorisedpersons(particularlychildren)shouldnotbe

allowedtoplaywithpermanentlyinstalledadjustingorcontrol devices.

− Keepremotecontrolbeyondthereachofchildren.

Regulations and bases for testingForconnecting,programmingandservicing,thefollowingregulations must be observed (the list is not exhaustive).

Construction product standards− EN13241-1(Productswithoutfireresistanceorsmoke

control characteristics)− EN12445(Safetyinuseofpoweroperateddoors-Test

methods)− EN12453(Safetyinuseofpoweroperateddoors-Re-

quirements)− EN12978(Safetydevicesforpoweroperateddoorsand

gates - Requirements and test methods)

EMC− EN55014-1(Electromagneticcompatibility-Requirements

for household appliances)− EN61000-3-2(Disturbancesinsupplysystems-harmonic

currents)− EN61000-3-3(Disturbancesinsupplysystems-voltage

fluctuations)− DINEN61000-6-2(Electromagneticcompatibility(EMC)

- Part 6-2: Generic standards – Immunity for industrial environments)

− DINEN61000-6-3(Electromagneticcompatibility(EMC)- Part 6-3: Generic standards – Emission standard for residential,commercialandlight-industrialenvironments)

Machinery Directive− EN60204-1(Safetyofmachinery,electricalequipmentof

machines Part 1: General requirements)− ENISO12100(Safetyofmachinery–generalprinciplesfor

design - risk assessment and risk reduction)


Low voltage− DINEN60335-1(Householdandsimilarelectricalappli-

ances-Safety-Part1:Part1:Generalrequirements)− DINEN60335-2-103(Householdandsimilarelectrical

appliances-Safety-Part2-103:Particularrequirementsfordrivesforgates,doorsandwindows)

CommitteeforWorkplaces(ASTA)− ASRA1.7(Workplaceregulation“Doorsandgates“)

General safety instructions− Toenablefault-freeoperationtobeguaranteed,itis

imperative that the rechargeable battery be replaced after every two years of operation. If this maintenance instruc-tionisdisregarded,thefunctionalsafetyofthesystemandthus also the safety of buildings and persons cannot be guaranteed.

− Toensurethatthesystemalwaysfunctionsconsistently,thefirealarmfunctionmustbecheckedonceeveryfourweeks.In order to check at the same time that the rechargeable batteryalsofunctionscorrectly,thecontrolmustbediscon-nectedfromthemains.Inthisway,theemergencyfunctioncan be checked to ensure that the door is closed automati-cally by the auxiliary motor.

− Emergencyoperationisnotpossibleifthereisafaultinthesafety circuit of the door operator.

− Toavoidadeepdischargeoftherechargeablebattery,thebatteryshouldnotbeconnectedtotheFS101unituntilthesystemisputintooperationforthefirsttime.Ifdeepdischargeoccurs,thebatterycannotberechargedagainand must be replaced immediately.

4. Overview of products

4.1 Product descriptionTheFS345controlcanbeusedinconnectionwithFDF,FT,FTAandFDSfire-protectiondrivesaswellaswithhydraulicdrives.InversionFS345HY,hydraulicdrivesareused.

TheFS345controlconsistofaCS300FSdoorcontrolunit,anFS101auxiliarycircuitboardandarechargeablebatteryforemergencypowersupply,magneticcouplings,DC-operat-edmotors,24Vmotorbrakes.

Incaseoffireorpowercuts,theemergencyrechargeablebattery provides the energy required for the auxiliary motor to close the door or for the motor brake to hold the door in position.

Thefiremodeistriggeredbyacontinuouscommandinthefirealarmcontactoristimeactivatedifthemainspowersup-plyfails.Inthecaseoffire,thedoorcloseswiththeclosingedgesystemdeactivated,or,optionally,withtheclosingedgeactivated.

4.2 Various optionsThefollowingmodelsofFS345controlcanbesupplied:− FS345controlfordeadmanoperation− FS345controlforautomaticoperation− FS345controlforautomaticoperationwiththeclosing

edgesystemactivatedinthecaseoffire

The following housing models are available:− HousingwithOPEN-STOP-CLOSEbuttons− HousingwithON/OFFkeyswitch− Housingwithmainswitch− HousingwithemergencyOFFswitch

The operating instructions describe the connection options andmodelsoftheFS345control.

General safety instructions

GB


4.3 Product drawing of CS 300 FS with FS 101

K06

K04 K05 K06 K07 K08 K09

K10

K11

K12

CS300FScircuit board

FS101circuit board

Battery

5. Commissioning

5.1 General information

Toguaranteethattheequipmentfunctionsproperly,itmustbe ensured that:− Thedoorisinstalledandoperational.− TheMFZoperatormotorisinstalledandreadyforopera-

tion.− Thecommandandsafetydevicesareinstalledandreadyfor

operation. − ThecontrolhousingwiththeFS345controlisinstalled.

REFERENCE

The relevant manufacturers’ instructions must be adhered to fortheinstallationofthedoor,theMFZoperatormotor,andthe command and safety devices.

5.2 Mains connection

PreconditionsToguaranteethatthecontrolfunctionproperly,thefollowingpoints must be ensured:- The mains voltage must correspond to the voltage stated on

the type plate.- The mains voltage must be the same as the voltage of the

operator.-Forathree-phasecurrent,aclockwiserotatingfieldis

required.-Forapermanentconnection,anall-polemainswitchmust

be used.-Forathree-phaseconnection,only3-wayautomaticcircuitbreakers(10A)maybeused.

NOTICE

Malfunctions can occur as a result of incorrect installation of the control!Beforeswitchingonthecontrolforthefirsttime,acheckmust be carried out after completing the wiring to ensure that all the motor connections at the motor and at the con-trolissecurelyfixed.Allcontrolvoltageinputsaregalvani-cally isolated from the supply.


5.3 Initial operation FS 101 emergency op-eration circuit board

GeneralTheFS101circuitboardincludesachargerfortherecharge-able battery and a microprocessor for controlling the auxiliary drive or the motor brake.ThecircuitboardisconnectedtotheCS300FSdoorcontrolunit in the factory and if it is purchased together with a door operator,thecorrectsettingsforthatoperatorarealsopresetin the factory.Allthatremainstobeconnectedisafirealarm,andtherechargeablebatterymustbeconnectedtotheFS101circuitboard via a plug.

NOTICE

Malfunctions due to incorrect installation of the battery!Topreventdeepdischargeoftherechargeablebattery,thebatteryshouldnotbeconnectedtotheFS101circuitboarduntilthedoorisputintooperation.Topreventerrors,thebatterymustbeconnectedtotheFS101circuitboardbefore the connection is made to the mains power supply.

5.4 Circuit diagram for mains connection and motor

CS 300 FS

L1 L2 L3 N

PE

PE

PE~

-

X1

T1

K2K1

U V W B1 B2X2

M1

400V / 50H

z / 3 / N / PE

1 3 5

2 4 6

1 3 5

2 4 6

M

L1N X12

Key: K1: CLOSEcontactorK2: OPENcontactorM1: MotorT1: TransformerX1: TerminalblockformainsconnectionX2: Terminalblockformotor

Connection:− Connectthecontroltothemainspowersupply.− Connectthecontroltothemotor.− Cablegroupsmustbesecuredclosetotheirrelevanttermi-

nals using a cable tie.

Initial operation

- +

Battery

FS101circuit board

Battery

GB


FS 101 - CS 300 FS (ready-wired)

FS101-P1-1


5.5 Mains power connection and motor 230 V AC version

CS 300 / FS 230 V AC, 3~

L1 L2 L3 N

PE

PE

PE~

-

X1

T1

K2K1

U V W B1 B2X2

M1

230V / 50H

z / 3 / PE

1 3 5

2 4 6

1 3 5

2 4 6

M

L1N X12

Key: K1: CLOSEcontactorK2: OPENcontactorM1: MotorT1: 230VtransformerX1: TerminalblockformainsconnectionX2: Terminalblockformotor



CS 300 / FS 230 V AC, 1~

L1 N

PE

PE

PE~

-

X1

T1

K2K1

AUF ZU N B1 B2X2

M1

230V / 50H

z / 1~ / PE

1 3 5

2 4 6

1 3 5

2 4 6

M

L1N X12

Key: K1: CLOSEcontactorK2: OPENcontactorM1: MotorT1: 230VtransformerX1: TerminalblockformainsconnectionX2: Terminalblockformotor



Initial operation

GB


5.6 Connection of command and safety devices for normal door operation X3/CS 300 FS

Command and safety devices can be connected via terminals X3andX4.

X3 / CS 300 FS

X6 / CS 300 FS

X7 / CS 300 FS

-DOWNSWITCH

- Impulse button

-UPSWITCH

-STOPbutton

-Emergencyoff,slackropeswitch,wicketdoorcontact,drawinprotection

-SocketsforinternalON-OFFswitch-Socketsforinternal3-buttoninputunit

STOP

OPEN

CLOSE


5.7 Connection examples for command and safety devices (terminal block X3/CS 300 FS)

OPEN / STOP / CLOSE buttons (6-lead solution)

1 2 3 4 5 6 7 8 9 10

OPEN / STOP / CLOSE buttons (4-lead solution)

1 2 3 4 5 6 7 8 9 10

ButtonSTOP

ButtonOPEN

ButtonCLOSE

ButtonSTOP

ButtonOPEN

ButtonCLOSE

UP / DOWN key switch

1 2 3 4 5 6 7 8 9 10

Impulse button key switch (sequence control)

1 2 3 4 5 6 7 8 9 10

ButtonOPEN

ButtonCLOSE

ButtonIMPULSE

Initial operation

GB


5.8 Connection examples for safety devices X4/CS 300 FS

Terminal block X48.2 kOhm closing edge safety device

Terminal block X4Optoelectronic closing edge safety system

+-

9

10

1

2

3

4

5

6

7

8wt

gr

br

GndSignal

+12V DC

24VDCforexternalswitching devices

Photoelectric drive-through barrier*

8.2 kOhm closing edge safety device*

HALFOPENlimitswitch



HALFOPENlimitswitch

Opto closing edge safety device*

Terminal block X4Pneumatic safety edge protection - pressure sensor test

8k2

Terminal block X4MFZ-type leading photoelectric barrier

+-

9

10

1

2

3

4

5

6

7

8wt

grbr

GndSignal

+12V DC

1

2

3

4

5

6

7

8

8k2

A 24VDCforexternalswitchingdevicesB Drive-through photoelectric barrier*C Leading photoelectric barrierD HALFOPENlimitswitch

Adjustmentofthepre-limitswitchCLOSEfortheleadingphotoelectric barrier− OntheCS300FS,setthemodeforrelay1to11(pre-limit

switchCLOSE)− Drivethedoorinthe“close”directionuntiltheleading

photocelljusttouchestheground.− Intheinputmenu,setthepre-limitswitchCLOSEtothis

position

* effective in down direction only



HALFOPENlimitswitch

Closing edge safety device

DW-Test*

A

B

C

D

X5 / CS 300 FSX4 / CS 300 FS

Relay 1MOD 11


5.9 Product drawing of FS 101 circuit board + rechargeable battery

K04 K05 K06 K07 K08 K09

K10

K11

K12

FS101-P1-1

X01

X02

X03

X04

X05

X10

X06X07

X08

X09

+ - AKKU

TEST

RES

ETTIME2

TIME1

S303

F200

ON

Battery

FS 101 circuit board

Key to FS 101 circuit board

X01/X02 Powersupply230V/PEX03 LimitswitchconnectionX04 Outputsfortheauxiliarymotor,brake, auxiliary relayX05 ActivationoftheCS300FScircuitboardX06 FirealarmconnectionX07 Potential-freeoutputforfaultindicatorX08 Potential-freeoutputforfirealarmX09 Potential-freeoutputforclosingedgesafety deviceX10 Input,external24V+-BATT Terminalblockforbatterypack

Time 1 Time-controlled closing if mains power supply failsTime 2 Timing element for door seal functionS303 DIPswitchReset Button – switch off buzzerTest Button for testing emergency operationF200 3.15AfuseforbatterychargerON Button

K04 AuxiliarymotorrelayK05 MotorbrakerelayK06 OPEN/CLOSEcommandrelayK07 UpperswitchrelayK07 LowerswitchrelayK09 StoprelayK10 Operation/errorrelayK11 EmergencyclosingrelayK12 Closingedgesafetydevice(SKS)relay

Initial operation

GB


5.10 DIP switches:

1ON DooroperatortypesFT(+HY)*1OFF DooroperatortypesFDF+FTA2 ON Fire alarm as normally open contact2 OFF Fire alarm as normally closed contact3ON Emergencyclosingwith400VAC/24VDC3OFF Emergencyclosingwith24VDC4ON WithCESD(SKS)inemergencyoperation4OFF WithoutCESD(SKS)inemergencyoperation5 ON Door closes if an error occurs5 OFF Door remains open if an error occurs6ON (OperatortypeHY)*6 OFF Operator type FT

WhenmakingchangestotheDIPswitchsettings,thefollow-ing procedure must be observed:1. Switchoffthemainsvoltage2. Switchofftherechargeablebatteryvoltage3. Change the DIP switch positions as required4. Switchontherechargeablebatteryvoltage5. Switchonthemainsvoltage

*versionHYonly

5.11 Types of door operator

TheFS345controlisdesignedforusewithtwodifferenttypes of door operator.

FT operatorsDIP 1 ON and DIP 6 OFF1.FTdooroperatorswith24VDCmotorbraking.Inemergencymode,thedoorisclosedviathe24VDCauxiliarymotor.The weight of the door is held by the ener-gised motor brake.The power supply comes from the mains adapterontheFS101circuitboard;ifthemainspowerisinterrupted,powerissuppliedfrom the rechargeable battery.(DIP6ONrequiredforversionHY)

FD (FDF, FTA, FDS) operatorsDIP 1 OFF1.FD(FDF,FTAandFDS)dooroperatorswitha24VDCauxiliarymotorand24VDCmotorbrake(FDF5).Inemergencymode,thedoorisclosedviathe24VDCauxiliarymotor.The power supply comes from the mains adapterontheFS101circuitboard;ifthemainspowerisinterrupted,powerissuppliedfrom the rechargeable battery.


5.12 FS 101 connections

2

1

2

1

2

1

2

1

2

1

X09

X08

X07

X06

X10

X051 2 3 4 5 6X03

X04

M

+-

* refer to the appendix for connection details for operators FT 3 and FDF 60

CESD(SKS)Potential-free relay

EMERGENCYOPERATIONPotential-free relay

OPERATION/ERRORPotential-free relay

INPUTFIREALARM

24VDC/50mA

Potential-free relayOPEN/CLOSEcommand

MotorbrakeforFT/FDFoperators*

Auxiliarymotor*

Initial operation

GB


5.13 Connection example for fire alarm con-tact

Terminal strip X06 (potential-free continuous contact as normally closed contact)

2

1

X06/FS101 Dip 2 = OFF

1

2

3

4

ON OFF

5

6

2

X10/FS101+-

1

Terminal strip X06 (potential-free continuous contact as normally open contact)

Dip 2 = ON

1

2

3

4

ON OFF

5

62

1

X06/FS101

2

X10/FS101+-

1

5.14 Messages

Terminal strip X07K10operation/errorrelay

X07/FS101

Innormaloperationcontactclosed,opensintheeventofanerror.Rechargeablebatteryfault/mainspowerfailure:switchesifthe battery is defective or if the battery voltage is less than 19V.

Fire alarm contact

Supplyvoltage24VDC,max.50mA

Fire alarm contact

Supplyvoltage24VDC,max.50mA

Terminal strip X08K11emergencyclosingrelay

X08/FS101

Potential-free switching contact for emergency operation is active.Switchesintheeventofemergencyclosing(contactclosed).

Terminal block X4K06operatorcommandrelay

X04/FS101

Potential-freeswitchingcontactforCLOSEorOPENcommanddepending on DIP switches 1 and 3. (See12and13.1forwiringandfunction)

Terminal strip X09K12closingedgesafetyedge(SKS)relay

X09/FS101

Potential-freeswitchingcontact,displaysstatusofCESD(SKS)


6. Limit switches

6.1 Limit switches

Connectionarrangementforlimitswitches(CS300terminalsX11,X10andFS101terminalsX03,X05)

1

2

3

4

5

6

7

8

X03/FS101**

1

2

3

4

5

6

7

8

9

10

8

7

6

5

4

3

2

1

6

5

4

3

2

1

5 6 7 8

X05/FS101*

X11/CS300 FS

X10/CS300 FS*

1

2

3

1 Limit switch OPEN2LimitswitchCLOSE3Pre-limitswitchCLOSE5Thermalprotection,motor*6 Emergency operation (normally closed contact)**7SafetylimitswitchCLOSE8SafetylimitswitchOPEN

* ready wired** ready wired if supplied with operator

The limit switches (with the exception of the pre-limit switch) areanalysedbytheFS101circuitboard,andthevaluesarepassedontotheCS300FScircuitboard.

� TheassignmentofterminalX11(limitswitch)isdifferentfromtheassignmentgiventoterminalsintheAS130.Thismustbetakenintoaccountintheeventofretrofits

Safetycircuit

-+CLOSEOPEN

GB


6.2 FDF / FTA / FDS limit switch settings

1. AdditionalOPENlimitswitch green2. Limit switch OPEN green3. SafetylimitswitchOPEN red4. SafetylimitswitchCLOSED red5. LimitswitchCLOSED white6. AdditionallimitswitchCLOSED white

NOTICE

Damage to property or irreparable damage due to incorrect adjustment!The door can be damaged if it is driven beyond the end positionwhileadjustmentsarebeingmade.

1. SelecttheADJUSTMENTmenuonthedisplay2. MovethedoortothedesiredCLOSEDpositionwiththe+

and - buttons.3. Setcontrolcam5(white)sothatthelimitswitchisactu-

ated.4. TightenfasteningscrewA.5. ScrewBcanbeusedtocarryoutfinetuning.6. MovethedoortothedesiredOPENpositionwiththe+

and - buttons.7. Setcontrolcam2(green)sothatthelimitswitchisactu-

ated.8. TightenfasteningscrewA.9. Safetylimitswitches3and5(red)mustbesetsothat

they are triggered as soon as the control limit switches are crossed.

10. Afterthetrialrun,checkthetightnessofthefasteningscrews.

11. Auxiliarylimitswitches1and6haveapotential-freechangeover contact


7.1 Overview of the LCD monitor

AUTOMATIC O

STANDBY

A

B

C D E

F

G

H

Key:A: Modeofoperation/DIAGNOSISinfoB: Parameters/DIAGNOSISinfoC Button(+)D: Button (-)E Button (P)F Value/statusG Value/statusH Jumper

7.2 LCD monitor, modes of operation

The control has four modes of operation with the LCD moni-tor:1.AUTOMATIC2.ADJUSTMENT3.INPUT4.DIAGNOSIS

IfjumperHisremoved,the(+)button,the(-)buttonandthe(P) button have no function. The display still functions.

Afterswitchingthecontrolon,itisinINITIALISATIONmode.ThedisplayshowsINITPHASEandthecontrolisnotyetreadyfor use. This phase lasts approx. 5 seconds.

7. Programming with the LCD monitor

6.3 FT limit switch settings

2. Limit switch OPEN green3. SafetylimitswitchOPEN red4. SafetylimitswitchCLOSED red5. LimitswitchCLOSED white6. AuxiliarylimitswitchCLOSED white

NOTICE

Damage to property or irreparable damage due to incorrect adjustment!The door can be damaged if it is driven beyond the end positionwhileadjustmentsarebeingmade.

1. SelecttheADJUSTMENTmenuonthedisplay2. MovethedoortothedesiredCLOSEDpositionwiththe+

and - buttons.3. Setcontrolcam5(white)sothatthelimitswitchisactu-

ated.4. TightenfasteningscrewA.5. ScrewBcanbeusedtocarryoutfinetuning.6. MovethedoortothedesiredOPENpositionwiththe+

and - buttons.7. Setcontrolcam2(green)sothatthelimitswitchisactu-

ated.8. TightenfasteningscrewA.9. Safetylimitswitches3and4(red)mustbesetsothat

they are triggered as soon as the control limit switches are crossed.

10. Afterthetrialrun,checkthatthefasteningscrewsarecor-rectly tightened.

11. Auxiliarylimitswitches1and6haveapotential-freechangeover contact

Limit switches

GB


ADJUSTMENT,INPUTandDIAGNOSISmodesareexitedau-tomatically20secondsafterthelastbuttonwaspressed,andthecontrolthengoesintoAUTOMATICmode.

Operating mode 1: AUTOMATICThedoorsystemisoperatedinAUTOMATICoperatingmode.

Display:− Displaystheactionbeingcarriedout− Displaysanyerrors

Ifthe“PRESS/REL"parameterissettoMOD2orMOD3intheinputmenu,thedisplaychangesfromAUTOMATICtoMANUAL.

Operating mode 2: ADJUSTMENTInADJUSTMENTmode,theOPEN/CLOSEDendpositionsareset.

NOTICE

Malfunctions can occur as a result of incorrect operation of the control! InADJUSTMENTmode,thedoorwillnotstopautomaticallywhen it reaches the travel limit position if electronic end positions(AWG)areused. The door can be damaged if driven beyond the end posi-tion.

FineadjustmentscanbemadeintheINPUToperatingmode.

Display:− Displaysthetravellimitvalue

Operating mode 3: INPUTIntheINPUToperatingmode,thevaluesofvariousparam-eters can be altered.

Display:− Displaystheselectedparameter− Displaysthecurrentvalueorstatus

Operating mode 4: DIAGNOSISIntheDIAGNOSISoperatingmode,door-specificcheckscanbe queried.

Display:− Displaysthemonitoredfunction− Displaysthestatusofthefunction


8. Navigator (LCD monitor only)

AUTOMATIC

STANDBY

P

> 1

sec

ond

ADJUSTMENT

STANDBY

+->Position,DOOROPEN

ADJUSTMENT

MAINUP

Dead

man

ope

ratio

n

Setthemechanicallimit

switc

hes

as d

escr

ibed

in s

ec-

tion

22.

-->PositionDOORCLOSED

ADJUSTMENT

MAINDOWN

P

> 1

sec

ond

INPUT

+ a

nd

- >

2 s

ec.

INPUT

ENGLISH

:Scrollupthroughmenu:

+ >

2 s

ec.

Scrolldownthroughmenu:

- >

2 s

ec.

Selectvalue:

P >

1 s

ec.

Incr

ease

val

ue:

+

Decr

ease

val

ue:

-

Savevalue:

P

Retu

rn to

INPUTmode:

+ a

nd

- >

1 s

ec

INPUT

RUNTIME

:60

P >

1 s

econd

INPUT

OPE

N T

IME

: 0

INPUT

PREW

ARNING

:0

INPUT

REVERS.TIME

:3

INPUT

MOD1-3STANDBY

:MOD1

INPUT

QUICKCLOSE

:

OFF

INPUT

RELAY1

:MOD6

INPUT

RELAY2

:MOD7

INPUT

RELAY3

:MOD1

INPUT

RELAY4

:MOD19

INPUT

DW-TEST

:OFF

INPUT

DELAYUP

:OFF

INPUT

PRESS/REL

:MOD1

INPUT

SU/WI

:MOD1

INPUT

REVERS.

:MOD1

DIAGNOSIS

Scrollupthroughmenu:

+ >

2 s

ec.


- >

2 s

ec.

ReturntoAUTOMATICmode:

P

Onl

y qu

erie

s ar

e po

ssib

le.

UPPERSW

ITCH

:ON

LOWERSWITCH

:OFF

UPSWITCH

:OFF

PARTUP

:OFF

DOWNSWITCH

:OFF

SKS

:OFF

IMP.INPUT

:OFF

SWITCHCLOCK

:OFF

LIGHTBARR.

:ON

STOPCIRCUIT

:ON

S-POINT1

:ON

S-POINT2

:ON

CYCLE

:XXXX

GB


AUTOMATIC

STANDBY

P

> 1

sec

ond

ADJUSTMENT

STANDBY

+->Position,DOOROPEN

ADJUSTMENT

MAINUP

Dead

man

ope

ratio

n

Setthemechanicallimit

switc

hes

as d

escr

ibed

in s

ec-

tion

22.

-->PositionDOORCLOSED

ADJUSTMENT

MAINDOWN

P

> 1

sec

ond

INPUT

+ a

nd

- >

2 s

ec.

INPUT

ENGLISH

:Scrollupthroughmenu:

+ >

2 s

ec.


- >

2 s

ec.

Selectvalue:

P >

1 s

ec.

Incr

ease

val

ue:

+

Decr

ease

val

ue:

-

Savevalue:

P

Retu

rn to

INPUTmode:

+ a

nd

- >

1 s

ec

INPUT

RUNTIME

:60

P >

1 s

econd

INPUT

OPE

N T

IME

: 0

INPUT

PREW

ARNING

:0

INPUT

REVERS.TIME

:3

INPUT

MOD1-3STANDBY

:MOD1

INPUT

QUICKCLOSE

:

OFF

INPUT

RELAY1

:MOD6

INPUT

RELAY2

:MOD7

INPUT

RELAY3

:MOD1

INPUT

RELAY4

:MOD19

INPUT

DW-TEST

:OFF

INPUT

DELAYUP

:OFF

INPUT

PRESS/REL

:MOD1

INPUT

SU/WI

:MOD1

INPUT

REVERS.

:MOD1

DIAGNOSIS

Scrollupthroughmenu:

+ >

2 s

ec.


- >

2 s

ec.

ReturntoAUTOMATICmode:

P

Onl

y qu

erie

s ar

e po

ssib

le.

UPPERSW

ITCH

:ON

LOWERSWITCH

:OFF

UPSWITCH

:OFF

PARTUP

:OFF

DOWNSWITCH

:OFF

SKS

:OFF

IMP.INPUT

:OFF

SWITCHCLOCK

:OFF

LIGHTBARR.

:ON

STOPCIRCUIT

:ON

S-POINT1

:ON

S-POINT2

:ON

CYCLE

:XXXX


9. Overview of functions

9.1 Automatic operating mode

Display Description

AUTOMATICOPEN

The door is driven to the OPEN end position

AUTOMATICCLOSE

ThedoorisdriventotheCLOSEDendposition

AUTOMATICSTANDBY

The door stands between the end positions

AUTOMATICOSTANDBY

The door stands at the OPEN end position

AUTOMATICoSTANDBY

ThedoorstandsatthePARTOPENposition("before-endposition"up)

AUTOMATICUSTANDBY

ThedoorstandsattheCLOSEDendposition

AUTOMATICuSTANDBY

ThedoorstandsatthePARTCLOSEDposition("before-endposition"down)

GB


9.2 Input operating mode

Function Description Setting options Factory settings

GERMAN Selectthemenulanguage DEUTSCHENGLISHFRANCAISNEDERLANDSESPANOLPOLSKICESKY

DEUTSCH

RUNTIME Monitoring the maximum running time for an open and closing movement. 1 – 250 seconds 60 seconds

OPEN TIME Afterthedoorhasopened,itrunsbackintheCLOSEdirectionafterthesettimehaselapsed.Open time > 0 = impulse functions only work in the OPEN direction

0 – 600 seconds 0=Autocloseoff

PREWARN-ING

Thewarninglightflashesbeforethedoorstartstoclose.Thepresetwarningtimeisonly active if the open time is > 0 or if operated via radio impulse.

0 - 120 seconds 0 = Off

REVERS.TIME

Standingtimeateverychangeofdirection 0.1 - 2.0 seconds (in1/10seconds)

0.3 seconds

MOD 1-3 STANDBY

MOD1: When resting OFFMOD2: When resting ON

MOD1MOD2

MOD1

QUICKCLOSE

ON: The open time is cut short after the photoelectric barrier has been passed (door closes immediately).OFF: The open time continues as usual.

ONOFF

OFF

RELAY1 Arelaymodulefrom1-18canbeassignedtothefirstthreerelays.MOD1:RedlightisonduringdoormovementandflashesasadvancedwarningMOD2:RedlightflashesduringdoormovementandflashesasadvancedwarningMOD3:RedlightflashesduringdoormovementandflashesasadvancedwarningTheparameterM3–1STAND.affectsthese3MOD.MOD4: Impulse when there is an OPEN commandMOD5: Error messageMOD6: OPEN end positionMOD7:CLOSEDendpositionMOD8: OPEN end position negatedMOD9:CLOSEDendpositionnegatedMOD10: Before-end position OPENMOD11:Before-endpositionCLOSEDMOD12:Before-endpositionCLOSEDtoCLOSEDendpositionMOD13: Magnetic lock functionMOD14 BrakeMOD15: Brake negatedMOD16: Brake remains ON during open timeMOD17: Brake remains ON during open time and direction turnaround (withaCESD(SKS)thebrakeisdeactivated)MOD18:RedlightflashesasawarningMOD19:CESD(SKS)

MOD1 – MOD18 MOD6

RELAY2 MOD1 – MOD18 MOD7

RELAY3 MOD1 – MOD18 MOD1

RELAY4 MOD 19 MOD19

DW-TEST ON: Pressure switch testing is active OFF: Pressure switch testing is not active

ONOFF

OFF

DELAYOPEN

ON: Gives warning before openingOFF: Immediate opening

ONOFF

OFF


Function Description Setting options Factory settings

PRESS/REL MOD1:AutomaticoperationMOD2:ManualoperationforOPEN+CLOSEMOD3:ManualoperationforCLOSE

MOD1 – MOD2 MOD1

SU/WI MOD1:PARTOPENatterminalblockX4(9/10)MOD2:PARTOPENselectorswitchatterminalblockX4(9/10)Whentheselectorswitchisclosed,allOPENcommandsgotothepre-limitswitchOPEN.

MOD1 – MOD2 MOD1

REVERS. MOD1:Thedoordoesnotreversewhenthepre-limitswitchCLOSEisactivated.MOD2:Thedoordoesnotreverse,evenifthepre-limitswitchCLOSEisactivated.

MOD1 – MOD2 MOD1

9.3 Diagnosis / error memory operating mode

Display Meaning Status

UPPERSWITCH OPEN end position OFF: activatedON: not activated

LOWERSWITCH CLOSEDendposition OFF: activatedON: not activated

UPSWITCH UPswitch ON: activatedOFF: not activated

PARTOPEN PARTOPENbutton ON: activatedOFF: not activated

DOWNSWITCH DOWNSWITCH ON: activatedOFF: not activated

SKS Closing edge safety device ON: circuit closedOFF: interrupted (fault)

IMPULSE Impulse button ON: activatedOFF: not activated

SWITCHCLK. Weekly timer ON: activatedOFF: not activated

LIGHTBARR. Photoelectric drive-through barrier ON: circuit closedOFF: interrupted (fault)

STOPCIRCUIT -Stopbuttononthecontrol-Stopsystemsintheoperator

ON: circuit closedOFF: interrupted (fault)

S-POINT1 -Stopbuttononthecontrol (keypad on cover)

OFF: activatedON: not activated

S-POINT2 Pre-limitswitchCLOSE OFF: activatedON: not activated

CYCLE Door cycle counter Displays number of door cycles

Overview of functions

GB


9.4 LED indications of the FS101

TheFS345controlunitisequippedwitharowofLEDsthatindicatethecurrentoperatingstatusofthesystemandindicateanyfaultsthat may occur. The following table gives an overview of the various faults and status conditions.

K04 K05 K06 K07 K08 K09

K10

K11

K12

FS

10

1-P

1-1

D018 D017 D016

D02 D01 D03

D04 D05D06 D07 D08 D09

D010 D011

D012

D013

D014

D015

D019

9.5 LED diagnostic FS 101

Code Colour Description Error diagnosis

D01 yellow LED safety circuit (inputX03/1,2)

LED ONLED OFF

OK- No power supply from mains or rechargeable battery - Operator safety circuit interrupted

D02 yellow LED limit switch OPEN (inputX03/3,4,5)

LED ONLED OFF

LimitswitchOPENnotconfirmedLimitswitchOPENconfirmed

D03 yellow LEDlimitswitchCLOSED (inputX03/6,7,8)

LED ONLED OFF

LimitswitchCLOSEDnotconfirmedLimitswitchCLOSEDconfirmed

D04 yellow LED auxiliary motor (outputX04/1,2)

LED ONLED OFF

AuxiliarymotorisactiveAuxiliarymotor24VDCisnotactive

D05 yellow LED motor brake (output X04/3,4)

LED ONLED OFF

Motor brake is switched onMotor brake is switched off

D06 yellow LEDdrivecommandopen/close (outputX04/5,6)

LED ONLED OFF

Drivecommandopen/closeonCS300FSisactiveDrivecommandopen/closeonCS300FSisnotactive

D07 yellow LED limit switch OPEN (outputX05/1,2)

LED ONLED OFF

LimitswitchOPENnotconfirmed-LimitswitchOPENconfirmed- Emergency operation is active

D08 yellow LEDlimitswitchCLOSED (outputX05/3,4)

LED ONLED OFF

LimitswitchCLOSEDnotconfirmedLimitswitchCLOSEDconfirmed



D09 yellow LED stop circuit (outputX05/5,6)

LED ONLED OFF

OK-Nopowersupplyfrommains/rechargeablebattery-Safetycircuitondriveunitinterrupted - Emergency operation is active

D010 yellow LEDCS300FSOPEN (inputX05/7,8)

LED ONLED OFF

DoorismovingtowardsOPENin400VoperationDoorisnotmovingtowardsOPENin400Voperation

D01 yellow LEDCS300FSOPEN (inputX05/9,10)

LED ONLED OFF

DoorismovingtowardsCLOSEDin400VoperationDoorisnotmovingtowardsCLOSEDin400Voperation

D012 yellow LEDfiredetector (inputX06/1,2)

LED ONLED OFF

Fire detector is closedFire detector is open (observe DIP 2 )

D013 yellow LEDoperation/fault (outputX07/3,4)

LED ONLED OFF

Operation/nofaultBatteryfault,mains

D014 yellow LED emergency operation (outputX08/1,2)

LED ONLED OFF

Emergency operation is active Emergency operation is not active

D015 yellow LEDSKS (outputX09/1,2)

LED ONLED OFF

SKSisOK SKSisinterrupted

D016 green LED charge maintenance LED ONLED OFF

Storagebatteryischarged,maintenancephaseStoragebatteryischarging

D017 yellow LED charge status LED ONLED OFF

Charging period Not in a charging period - battery charged

D018 red LED battery fault LED ONLED OFF

Batterydefective,CHANGEBATTERY!BatteryOK

9.6 Diagnostic LED D019 F101

Code D 019, colour red

Diagnostic LED (red) Error / status / info Action

Flashes once Battery fault Rechargeable battery is defective: replace

Flashes 2 times Mains power failure BatterychargerDef.;FS101fuseF2Def.

Flashes 3 times CommandreceivedfromfirealarmorfromT1,thedoorwillclose

Flashes 4 times DoorhasbeenclosedbythefirealarmorbyT1

Flashes 5 times SafetycircuitinputX03/1+2hasbeeninterrupted Check the safety circuit of the door operator

Flashes 6 times HYleak(versionFS345HY)) Check the hydraulic system

Flashes 7 times SKSdefectiveatOPENendposition CheckSKS

Flashes 8 times Door has been closed due to an error


GB


Error diagnosis CS 300 FS


H4 green LED closing edge safety deviceLED ONLED OFF

OK- Closing edge safety device interrupted- Closing edge safety device defective

Fault / error message Cause RectificationSystemdoesnotrespond - No voltage supply Check the voltage supply to the operator and the

controlDoortravelstotheCLOSEDendpositionwhentheUPbuttonispressed

-Rotatingfieldisconnectedwrongly -Checktherotatingfieldandsettoclockwiserotatingfield,ifnecessary

ERRORENDPOS. -TheOPENandCLOSEDlimitswitchesarebothopen,althoughatleastonelimitswitchshouldbe closed

ChecktheconnectionatX11Check the limit switch connectionsCheck the limit switch settings

ERRORRUNTIME The programmed running time has been exceeded Check the path of the doorRe-programme the running time

ERRORSKS The closing edge safety edge is faultyThe closing edge safety device was activated

Check the closing edge safety device and the spiral cableRemove obstruction from path of door

ERRORPRESSURESWITCHTESTING The pressure sensor is not triggered at the CLOSEDendposition

Checkthepressuresensor,spiralcableandprofileCheckthesettingfortheCLOSEDendposition

Battery Standby

No mains power supplyEmergency operation

Checkmainspowersupply(L,N)


9.7 Adjustment options for TIME 1 (door closes if the mains supply fails)

Withtimer1,thecontrolcandelaytheautomaticclosingofthe door after mains power failure by a set period. When set to0,thedoordoesnotcloseautomaticallyintheeventofmains failure.If the timer is set to 0 and the mains supply is cut off for a longerperiod,thedeepdischargeprotectionsystemforthecontrolcomesintoplay.See17.1.

0 - No automatic closing in the event of mains failure1 - In the event of a power cut: closes after 5 seconds2 - In the event of a power cut: closes after 15 seconds3 - In the event of a power cut: closes after 30 seconds4 - In the event of a power cut: closes after 1 minute5 - In the event of a power cut: closes after 2 minutes6 - In the event of a power cut: closes after 5 minutes7 - In the event of a power cut: closes after 15 minutes8 - In the event of a power cut: closes after 30 minutes9 - In the event of a power cut: closes after 60 minutes

9.8 Automatic mode with active closing edge safety device in emergency operation

It is possible to monitor emergency operation with a contact bar.Ifthecontactbaristriggered,thedoorstopsinemergen-cyoperation.Afterthecontactbarisfreeagainandadelayof2secondshaselapsed,emergencyclosingiscontinued.Reversing does not take place. The function of the closing edgesafetydevice(SKS)ischeckedintheupperendposition.Ifadiscernibleerrorisdetected,emergencyoperationtakesplacewithoutanevaluationoftheSKS.

Prerequisites: − CS300FSisconnectedtoFS101(seedrawing) − Relay mode 19 is set for relay 4 (factory setting) − FS101DIPswitch4isON(switchoffmainsvoltageand

battery power) − CESD(SKS)isconnectedtoterminalX4ofCS300FS

Connection between CS 300 FS + FS 101

7

8

X5

K05 K06 K07 K08 K09

+

-24VDC

Relay 4

CS 300 FSBatteryFS101


GB


9.9 Emergency closing with 400 V DC opera-tor

It is possible for the door to be closed using the door operator whenthefirealarmisactivated.

Prerequisites:− ConnectCS300X3/9+10toFS101X04/5+6.− FS101DIPswitch3isON(switchoffmainsvoltageand

battery power)

Connect CS 300 FS circuit board +

9

10

5

6

X3 X04CS 300 FS FS101

Inthiscase,ifasignalisgivenbythefirealarmandmainspowerisavailable,theFS101circuitboardgivesaDOWNim-pulse �X3totheCS300FScircuitboardviaterminalX06.ThedoorisdriventotheCLOSEDendpositioninimpulsemode. The safety devices integrated are active. Once the CLOSEDendpositionhasbeenreached,thedoorcannotbeopened again. IftheCESD(SKS)isactivatedduringtheclosingphase,thedoorreversesandstopsattheOPENendposition.After30secondsafurtherDOWNimpulseissent.IftheCESD(SKS)interruptstheclosingphaseagain,theprocessisrepeated3timesintotal.IftheCLOSEDendpositionhasnotbeenreachedafter90seconds,thedooristhenclosedviaemer-gency operation mode.

9.10 Door sealing function for FT fire door operators

To ensure that the sections of the door close together tightly inemergencymode,thedoormustbedrivenbeyondtheCLOSElimitswitch.WiththeFS345control,thisfunctionistimecontrolledandissetusingTIMER2.Avalueof0to5secondscanbeselected.

Prerequisites: − Door operator type FT (DIP 1 is set to ON) − The system has been set in operation and the limit switches

have been set.

Settings:1. OPENandCLOSElimitswitchesaresetfornormal door operation.2. Settimer2tothemid-rangevalueof2.5seconds.3. Drive the door to the OPEN end position.4. Switchoffthemainsvoltagesupplyandpressthe TESTbutton.5. ThedoorrunstotheCLOSEDendpositioninemer gency operation mode.6. ThedooristhendrivenbeyondtheCLOSElimitswitch for 2.5 seconds. Only then is power supplied to the motor brake again and the door is held in position.7. Repeat steps 2 to 6 entering different values for timer 2 until optimum results are achieved.8. TheCLOSEsafetylimitswitchmustbesetaccordingly.


TheFS345controlunitaffordsprotectionagainstdeepdis-charge of the battery and can carry out regular tests to check the condition of the battery.

10.1 Checking the rechargeable battery and emergency operation

� Toensurethatthesystemalwaysfunctionsconsistently,thefirealarmfunctionmustbecheckedonceeveryfourweeks.In order to check at the same time that the rechargeable batteryalsofunctionscorrectly,thecontrolmustbediscon-nected from the mains. This is the only way to demonstrate that the emergency function is operational and that the door closes automatically via the auxiliary motor.

Procedure: − Drive the door to the OPEN end position.− Switchoffthemainspowersupply.− PressTESTbutton:Emergencyoperationisstartedaftera

delay of 2 seconds.

Check:afterpressingtheTESTbutton

1. the battery test is started � LED indicator

2. The integrated buzzer sounds3. After2seconds,thedoorisdriventotheCLOSEDend

position4. The buzzer stops5. � LED indicator

6. The buzzer sounds once7. The test is over

10. Rechargeable battery and battery charger

9.11 Integrated buzzer and RESET buttonTheFS345controlunithasanintegratedbuzzerthatgivesan acoustic signal to indicate emergency operation and the condition of the rechargeable battery.

The buzzer sounds during emergency closing and stops when itreachesitsCLOSEDendposition.The alarm also sounds if a faulty battery is detected during operation or during a test.The acoustic warning signal can also be switched off using theRESETbuttonintheCLOSEDdoorposition.Thebatteryneeds to be changed.

Buzzer1 tone sounds at intervals of 5 seconds

No mains voltage

1 tone sounds at intervals of 2 seconds

Rechargeable battery is defective

4 short tones Warning before emergency closing

1 tone sounds at intervals of a second

Emergency closing


GB


10.2 Protection against deep discharge

If,followinginitialoperation,thecontrolisoperatedforalengthyperiodwithoutanexternalpowersupply,thecontrolisswitchedoffafteradefinedperiodtopreventdeepdischarging of the battery. The period of time depends on the type of operator and so from the external consumer devices.

DIP1ON Switchesoffafter8hourswithoutexternal mains supply voltageDIP1OFF Switchesoffafter48hourswithoutexternal mains supply voltage

The buzzer sounds continuously for 60 seconds to signal that thebattery,andthereforealsothecontrolunit,hasbeenswitched off.

If timer 1 is to be set to nought (door does not close if mains powerfails),thedoorclosesinacontrolledmannerorisleftopen depending on the setting of DIP switch 5. It is only pos-sible to keep the door open in a controlled way if DIP switch 1 is OFF:

DIP5ON Doorclosesafterthesignalbuzzersounds, thebattery/controlisswitchedoffDIP5OFF Doorremainsopen,thebattery/controlis switched off

The control can only be switched on again if the external volt-age supply is reconnected.

For FT types of operator (DIP 1 ON), if the mains sup-ply has been interrupted for a period of 8 hours or longer, the battery is charged for 30 minutes as soon as the mains voltage is switched back on. The door control cannot operate during this charging period.This charging status is indicated via the recharge LED and can be interrupted by pressing the RESET button.

Lights up Flashes

alternately

10.3 Cyclic testing of the rechargeable battery

TheFS345controlisabletotesttheconditionoftherechargeablebatteryautomatically.Innormaloperation,thebattery is disconnected from the control every 60 minutes and the battery voltage is checked.

Ifthebatteryvoltagefallsbelowaspecifiedvalue(19V),thisisrecognisedasafault,whichisthenindicatedviathefaultrelay,thebuzzerandthediagnosticLED.Itcouldbethat proper operation in emergency mode is then no longer possible.

DIP switch 5 can be set to specify whether the door closes or stays open in this case.

DIP5ON Thedoorcloses,thebatteryisswitchedoffDIP5OFF Doorremainsopen,thebattery/controlis switched off

Connection between CS 300 FS + FS 101

9

10

5

6

X3 X04CS 300FS FS101

DIP 5 ON

123

4

ON OFF

5

6


NOTICE

Damage due to improper use of charging device!TheFS101circuitboardchargerissuitableforchargingmaintenance-free lead batteries only. The battery charger may only be opened by authorised persons and must only be used if closed.The warranty will be invalid if the charging device becomes damaged due to improper opening.Ensure that there is adequate ventilation before using the deviceforthefirsttime.The device must only be used in closed rooms and must not be exposed to dampness and humidity.Alterations of any kind to the device will invalidate the warranty.

10.4 Recharging the battery

NOTICE

Incorrect charging of maintenance-free lead batter-ies may result in faults or failures!Before not using for any length of time (two options)

− Disconnect your battery from the charger and store the battery in its fully charged state

(if not using for more than three months, charge for at least 36 hours)

− Youcancontinuetochargeyourbatteryindefinitelywiththe battery charger switched on (maintenance charging). We recommend storing the batteries in a cool room.

High temperaturesCharging the battery at temperatures of over 30°C is not recommended.Yourbatterychargerisfactorysettoacharging voltage which is designed for an ambient tem-perature of 20°C.

Low temperaturesCharging the battery at temperatures under 10°C is not recommended.Atlowtemperatures,theavailablecapacityis reduced.

Deep dischargePlease avoid deep discharging of your battery. If deep batterydischargeoccurs,however,replacethebatteryim-mediately.

CAUTION!

Risk of injury through use of charging devices! − (due to the formation of explosive gases when charging

lead-acid batteries) − Dangeroffireandshort-circuit(due to electric shock in

moist conditions)To prevent any danger:

− Ensure that the area is adequately ventilated. − Avoidfireandnakedlights. − Usetheplug-inpowerpackonlyindryrooms. − Protect the device from moisture.

Battery and battery charger

GB



11.1 Motor brake connection diagram for FT 3 / FT 4 / FT 5 operator

CS300FS auxiliary mains adapter24VDC

24VDCmo-tor brake

11. Motor brake and auxiliary motor

L NNL1

+ -

X12

K14

K13

K13 K14

1 2X13

GB


11.2 Auxiliary motor connection diagram for FDF 60 operator

12-+

M

BatteryFDF 60

auxiliary motor power relayauxiliary motor


12. Technical data

12.1 Mechanical and electrical data

Housingdimensions: 750 x 300 x 132 mm

Installation: Verticalmountingonthewall, minimumheightabovefloor=1,100 mm

Supplyvoltage: 3~400VAC,50Hz,+/-10%STANDARD3~230VAC,50Hz,+/-10%SPECIALSOLU-TIONOther voltages on request

Fuse protection: 10AKtype

Power input: Max. 2.2 kW

Internal consumption of control:

Max.powerconsumptionoftheCS300FScontrolitself=250mAonsecondarysideMax.powerconsumptionoftheFS101controlitself=200mAonsecondaryside

Motor data: max.2.2kWAC/-3.2A.

Control voltage: 24VDC,allinputconnectionsmustbepotential-free;minimumsignaldurationforinput control command >100 ms

Control outputs: 24VDC,maximumof500mA

Batteries Maintenance-freebatterieswithVdScertifica-tion

Fault output relay: If inductive loads are connected (e.g. further relaysorbrakes),thesemustbefittedwithap-propriatesuppressorelements(recoverydiodes,varistors,RCcircuits).Potential-freenormallyopencontact;min.10mA;max.230V230VAC~4AOnce contacts have been used for power cir-cuits,theycannolongerbeusedforextra-lowcurrent circuits.

Emergency operation output relay:

If inductive loads are connected (e.g. further relaysorbrakes),thesemustbefittedwithap-propriatesuppressorelements(recoverydiodes,varistors,RCcircuits).Potential-freenormallyopencontact;min.10mA;max.230V230VAC~16AOnce contacts have been used for power cir-cuits,theycannolongerbeusedforextra-lowcurrent circuits.

Temperature range: Operation: +5°C…+55°CStorage: -20°C…+85°C

Airhumidity: Upto80%withnocondensation

Vibrations: Low-vibrationmounting,e.g.onamasonrywall

Type of protection: IP 54

Weight: approx. 10.5 kg

13. Maintenance

TheFS345controlismaintenance-free.

DANGER!

Life-threatening danger due to electric shock! � ThecontrolunitordoorsystemMUSTbedisconnectedfrom the electricity supply before carrying out any electri-cal work. Take measures to ensure that the power supply remains disconnected for the duration of the work.

The following points must be taken into account when carry-ing out maintenance on the door system:Maintenance must only be carried out by authorised persons.DirectiveASRA1.7mustbecompliedwith.Worn or faulty parts must be replaced.Only approved parts may be installed.Allmaintenanceworkmustbedocumented.Replaced fault parts must be disposed of properly in accord-ance with the materials they contain and local regulations.

GB


14. EC Declaration of Incorporation

We hereby declare that the product described below:FS 345 Door Controlis in conformity with all essential requirements of the Machin-eryDirective2006/42/EC.

Inaddition,thepartlycompletedmachineryisinconformitywithallregulationsoftheEUConstructionProductsRegula-tionNo.305/2011,theElectromagneticCompatibilityDirective2004/108/ECandtheLowVoltageDirective2006/95/EC.

The following standards were applied:

EN 60204-1Safetyofmachinery,electricalequipmentofmachines;Part1:General requirements

ENISO12100Safetyofmachinery–generalprinciplesfordesign-riskas-sessment and risk reduction

DIN EN 12453Safetyinuseofpoweroperateddoors-Requirements

DIN EN 61000-6-2 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments

DIN EN 61000-6-3Electromagnetic compatibility (EMC) - Part 6-3: Genericstandards-Emission-standardforresidential,com-mercial and light-industrial environments

DIN EN 60335-1Householdandsimilarelectricalappliances-Safety-Part1:General requirements

DIN EN 60335-2-103Householdandsimilarelectricalappliances-Safety-Part2-103:Particularrequirementsfordrivesforgates,doorsandwindows

The relevant technical documentation is compiled in ac-cordancewithAnnexVII(B)oftheECMachineryDirective2006/42/EC.Weundertaketotransmit,inresponsetoareasonedrequestbythemarketsurveillanceauthorities,thisinformation in electronic form within a reasonable term.

Person authorised to compile the relevant technical documen-tation: MFZAntriebeGmbH&Co.KG,NeueMühle4, D-48739 Legden The machinery is incomplete and must not be put into service until the machinery into which it is to be incorporated has been declared in conformity with the provisions of the Ma-chineryDirective2006/42/EC.

Place / Date:Legden,01/03/2014

Manufacturer’s signature

Dirk Wesseling

Position of signatoryManagement

GB


#1700009439

operating instructions for fs 345 with fs 101 and cs 300 fs gb

Documents