osha citations against o&g and ducci electric

U.S. Department of Labor

Occupational Safety and Health Administration 1057 Broad Street Bridgeport, CT 06604 Phone: (203)579-5581 FAX: (203)579-5516

Citation and Notification of Penalty

To: Inspection Number: 109179937 O&G Industries Inc. Inspection Date(s): 02/07/2010-08/02/2010 and its successors Issuance Date: 08/03/2010 112 Wall Street Torrington, CT 06790

The violation(s) described in this Citation and Notification of Penalty is (are) alleged to have occurred on or about the day(s) the inspection was made unless otherwise

Inspection Site: 1349 River Road Middletown, CT 06457

Citation and Notification of Penalty of 83 OSHA-2(Rev. 6/93)

indicated within the description given below. This Citation and Notification of Penalty (this Citation) describes violations of the Occupational Safety and Health Act of 1970. The penalty(ies) listed herein is (are) based on these violations. You must abate the violations referred to in this Citation by the dates listed and pay the penalties proposed, unless within 15 working days (excluding weekends and Federal holidays) from your receipt of this Citation and Notification of Penalty you mail a notice of contest to the U.S. Department of Labor Area Office at the address shown above. Please refer to the enclosed booklet (OSHA 3000) which outlines your rights and responsibilities and which should be read in conjunction with this form. Issuance of this Citation does not constitute a finding that a violation of the Act has occurred unless there is a failure to contest as provided for in the Act or, if contested, unless this Citation is affirmed by the Review Commission or a court. Posting - The law requires that a copy of this Citation and Notification of Penalty be posted immediately in a prominent place at or near the location of the violation(s) cited herein, or, if it is not practicable because of the nature of the employer's operations, where it will be readily observable by all affected employees. This Citation must remain posted until the violation(s) cited herein has (have) been abated, or for 3 working days (excluding weekends and Federal holidays), whichever is longer. The penalty dollar amounts need not be posted and may be marked out or covered up prior to posting. Informal Conference - An informal conference is not required. However, if you wish to have such a conference you may request one with the Area Director during the 15 working day contest period. During such an informal conference you may present any evidence or views which you believe would support an adjustment to the citation(s) and/or penalty(ies). If you are considering a request for an informal conference to discuss any issues related to this Citation and Notification of Penalty, you must take care to schedule it early enough to allow time to contest after the informal conference, should you decide to do so. Please keep in mind that a written letter of intent to contest must be submitted


to the Area Director within 15 working days of your receipt of this Citation. The running of this contest period is not interrupted by an informal conference. If you decide to request an informal conference, please complete, remove and post the page 4 Notice to Employees next to this Citation and Notification of Penalty as soon as the time, date, and place of the informal conference have been determined. Be sure to bring to the conference any and all supporting documentation of existing conditions as well as any abatement steps taken thus far. If conditions warrant, we can enter into an informal settlement agreement which amicably resolves this matter without litigation or contest. Right to Contest - You have the right to contest this Citation and Notification of Penalty. You may contest all citation items or only individual items. You may also contest proposed penalties and/or abatement dates without contesting the underlying violations. Unless you inform the Area Director in writing that you intend to contest the citation(s) and/or proposed penalty(ies) within 15 working days after receipt, the citation(s) and the proposed penalty(ies) will become a final order of the Occupational Safety and Health Review Commission and may not be reviewed by any court or agency. Penalty Payment - Penalties are due within 15 working days of receipt of this notification unless contested. (See the enclosed booklet and the additional information provided related to the Debt Collection Act of 1982.) Make your check or money order payable to "DOL-OSHA". Please indicate the Inspection Number on the remittance. OSHA does not agree to any restrictions or conditions or endorsements put on any check or money order for less than the full amount due, and will cash the check or money order as if these restrictions, conditions, or endorsements do not exist. Notification of Corrective Action - For each violation which you do not contest, you must notify the Area Director of the Bridgeport OSHA Area Office, by letter, within 10 calendar days after each abatement date, that you have taken appropriate corrective action within the time frame set forth on this Citation. Where the citation indicates that abatement certification is necessary, only the abatement method and date when abatement occurred are required. Where the citation indicates that abatement documentation is necessary, evidence of the purchase or repair of equipment, photographs or video, receipts, etc., verifying that abatement has occurred is required. The abatement letter must be posted at the location where the violation appeared and the corrective action took place or employees must otherwise be effectively informed about abatement activities. A sample abatement certification letter is enclosed with this Citation. Employer Discrimination Unlawful - The law prohibits discrimination by an employer against an employee for filing a complaint or for exercising any rights under this Act. An employee who believes that he/she has been discriminated against may file a complaint no later than 30 days after the discrimination occurred with the U.S. Department of Labor Area Office at the address shown above. Employer Rights and Responsibilities - The enclosed booklet (OSHA 3000) outlines additional employer rights and responsibilities and should be read in conjunction with this notification.


Notice to Employees - The law gives an employee or his/her representative the opportunity to object to any abatement date set for a violation if he/she believes the date to be unreasonable. The contest must be mailed to the U.S. Department of Labor Area Office at the address shown above and postmarked within 15 working days (excluding weekends and Federal holidays) of the receipt by the employer of this Citation and Notification of Penalty. Inspection Activity Data - You should be aware that OSHA publishes information on its inspection and citation activity on the Internet under the provisions of the Electronic Freedom of Information Act. The information related to these alleged violations will be posted when our system indicates that you have received this citation, but not sooner than 30 calendar days after the Citation Issuance Date. You are encouraged to review the information concerning your establishment at www.osha.gov. If you have any dispute with the accuracy of the information displayed, please contact this office.


Occupational Safety and Health Administration

NOTICE TO EMPLOYEES OF INFORMAL CONFERENCE

An informal conference has been scheduled with OSHA to discuss the citation(s) issued on

08/03/2010. The conference will be held at the OSHA office located at 1057 Broad Street,

Bridgeport, CT, 06604 on _____________ at _____________. Employees and/or representatives of

employees have a right to attend an informal conference.


U.S. Department of Labor Inspection Number: 109179937 Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010

Issuance Date: 08/03/2010 Citation and Notification of Penalty Company Name: O&G Industries Inc. Inspection Site: 1349 River Road, Middletown, CT 06457

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities. Citation and Notification of Penalty of 83 OSHA-2 (Rev. 9/93)

Citation 1 Item 1 Type of Violation: Serious 29 CFR 1926.21(b)(6)(i): The employer did not comply with any specific regulations that apply to work in dangerous or potentially dangerous areas where employees were required to enter into confined or enclosed spaces. a.Site - Employees required to enter into confined spaces were not instructed as to the nature of the hazards involved,

the necessary precautions to be taken and in the use of protective and emergency equipment required.

ABATEMENT NOTE: For the purposes for paragraph (b)(6)(i) of this section, "confined or enclosed space" means any space having limited means of egress, which is subject to the accumulation of toxic or flammable contaminants or has oxygen deficient atmosphere. Confined or enclosed spaces include, but are not limited to, storage tanks, process vessels, bins, boilers, ventilation or exhaust ducts, sewers, underground utility vaults, tunnels, pipelines and open top spaces more than 4 feet in depth such as pits, tubes, vaults and vessels. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 2 Type of Violation: Serious 29 CFR 1926.24: The employer did not develop and maintain an effective fire protection and prevention program at the job site throughout all phases of the construction, repair, alteration, or demolition work: a.Site - An effective fire protection and prevention program was not developed nor maintained. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




The alleged violations below have been grouped because they involve similar or related hazards that may increase the potential for injury resulting from an accident.

Citation 1 Item 3a Type of Violation: Serious 29 CFR 1926.28(a): Appropriate personal protective equipment was not worn by employee(s) in all operations where there was exposure to hazardous conditions: a.Site: Employees working in the HRSG #1 knockout tank sump area and exposed to drowning hazards were not

wearing personal flotation devices. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 3b Type of Violation: Serious 29 CFR 1926.106(a): Employee(s) working over or near water where the danger of drowning existed, were not provided with U.S. Coast Guard approved life jacket(s) or buoyant work vest(s): a.Site: Employees working in the HRSG #1 knockout tank sump area and exposed to drowning hazards were not

provided with personal flotation devices. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010




Citation 1 Item 4 Type of Violation: Serious 29 CFR 1926.65(q)(1): The employer did not develop and implement an emergency response plan to handle anticipated emergencies prior to the commencement of emergency response operations. a.Site - An emergency response plan was not developed and implemented. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 5 Type of Violation: Serious 29 CFR 1926.150(e)(1): An alarm system was not established by the employer whereby employees on the site could be alerted for emergencies: a.Site - An alarm system had not been established where employees onsite could be alerted for emergencies. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 6 Type of Violation: Serious 29 CFR 1926.150(e)(2): The alarm code or reporting instructions were not conspicuously posted at phones or at employee entrances: a.Site - Alarm codes were not posted. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 7 Type of Violation: Serious 29 CFR 1926.153(j): Container(s) of liquefied petroleum gas (LPG) were stored within building(s): a.Throughout the Site - Three LPG cylinders were stored indoors. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 8 Type of Violation: Serious 29 CFR 1926.405(a)(2)(ii)(C): Receptacles for uses other than temporary lighting were installed on branch circuits which supplied temporary lighting: a.Gas Compressor Building: Receptacles for temporary power and temporary lighting were installed on the same

branch circuit. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 9 Type of Violation: Serious 29 CFR 1926.453(b)(2)(v): A Safety Harness was not worn and a lanyard attached to the boom or basket when working from an aerial lift. a.Power Generation Building, Between CT#1 and CT#2 @ Column G-4: An employee who was working in an

aerial lift was not tied off with a full body harness and lanyard attached. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 10 Type of Violation: Serious 29 CFR 1926.501(b)(4)(i): Each employee on walking/working surfaces were not protected from falling through holes more than 6 feet above lower levels, by personal fall arrest systems, covers, or guardrail systems erected around such holes: a.Power Generation Building, Alongside CT#1: Employees were not protected from stepping into holes by the use

of covers. b.Power Generation Building, Alongside CT#2: Employees were not protected from stepping into holes by the use

of covers. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 11 Type of Violation: Serious 29 CFR 1926.502(i)(4): All covers were not secured when installed so as to prevent accidental displacement by the wind, equipment, or employees: a.Between HRSG 1 and HRSG2 - Floor hole covers were not secured. b.Near Water Treatment Building - Floor hole covers were not secured. c.East side of HRSG #1 - Floor hole covers were not secured. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 12 Type of Violation: Serious 29 CFR 1926.502(i)(4): All covers were not color coded or marked with the word "HOLE" or "COVER" to provide warning of the hazard: a.Between HRSG 1 and HRSG2 - Floor hole covers were not color coded nor marked. b.Near Water Treatment Building - Floor hole covers were not color coded nor marked. c.East side of HRSG #1 - Floor hole covers were not color coded nor marked. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 13 Type of Violation: Serious 29 CFR 1926.602(c)(1)(ii): Modifications or additions which will affect the capacity or safe operations of the equipment or reduce the orginial safety factor were made without the manufacturer's written approval. a.Outside of Power Generation Building Fork extensions were used on a JLG forklift without the manufacturer's

written approval. Also the capacity tags on the unit had not been updated to reflect the added piece of equipment.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 14 Type of Violation: Serious 29 CFR 1926.1053(b)(1): When the side rails of portable ladder(s) were unable to extend at least 3 feet above the landing because of the portable ladder's length, the ladder(s) were not secured at top to rigid support(s) and grasping devices, such as a grabrail were not provided: a.Power Generation Building - Where the side rails of a stepladder could not extend above the electrical cabinets,

the ladder was not secured at top to rigid support(s) and a grasping device, such as a grabrail, was not provided.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 15 Type of Violation: Serious 29 CFR 1926.1053(b)(13): The top or top step of a stepladder was used as a step: a.Power Generation Building - When accessing the top of an electrical cabinet, workers were using the top step and

top of the stepladder. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 2 Item 1 Type of Violation: Willful Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employmnent and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazards of falls, drowning and/or asphyxiation: a.Site: Workers were exposed to the hazards of falls, drowning and asphyxiation when they were allowed to enter

confined spaces without benefit of air monitoring, fall protection and/or protection from drowning. ABATEMENT NOTE: Among other methods, one feasible and acceptable means of abatement is to follow ANSI/ASSE Z117.1-2009, entitled Safety Requirements for Confined Spaces. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 2 Type of Violation: Willful Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm in that the method used to clean the 561 main fuel gas line pipes - blowing natural gas through them at high velocity - was not implemented in such a way as to protect employees from the hazard of an explosion caused by venting large amounts of natural gas into areas where it could accumulate and where, or in close proximity to where, ignition sources existed. The following conditions and practices contributed to the existence of this hazard: the vent pipe configured close to and below scaffolding, in close proximity to the Power Generation Building, in between two approximately 115 foot tall Heat Recovery Steam Generators (HRSGs) and well below the tops of all of those structures; the failure to eliminate open flame ignition sources, including but not limited to propane heaters; construction work occurring during the gas blow process; individuals other than those essential to conducting the gas blows working in the area during the gas blow process; and the inability to readily control the amount of gas and pressure flowing through the main gas fuel line. On February 7, 2010, employees were exposed to serious or fatal impact and other injuries from an explosion hazard created when a large amount of natural gas was blown at high velocity through CT#1 Main Knockout Drum Vent Pipe (561-TNK-1002) into the area between the two HRSGs and close to buildings, scaffolding, partially enclosed work areas, and other structures that were adjacent to the Power Generation Building in which employees worked and in or around which open flame ignition sources, including but not limited to propane heaters, existed, construction work was occurring, and numerous employees non-essential to conducting the gas blow were working. When natural gas is chosen for this method of cleaning gas line pipes, feasible means of abatement to eliminate or materially reduce the hazard are to ensure that the vent pipe is positioned vertically and above the Power Generation Building and all other nearby structures, or horizontally to a location away from structures that could inhibit the adequate dispersal of the gas; ensure that any and all ignition sources are eliminated; ensure that any and all construction activity ceases during the gas blow process; ensure that all workers other than those essential to conducting the gas blows are removed from the building and area around which the gas blows are occurring; and ensure the use of devices to control the amount and pressure of gas vented, such as a fast closing pipe shut-off valve and a gas pressure control valve. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010




Proposed Penalty: $ 70000.00




Citation 2 Item 3 Type of Violation: Willful Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm in that the method used to clean the 561 main fuel gas line pipes - blowing natural gas through them at high velocity - was not implemented in such a way as to protect employees from the hazard of an explosion caused by venting large amounts of natural gas into areas where it could accumulate and where, or in close proximity to where, ignition sources existed. The following conditions and practices contributed to the existence of this hazard: the vent pipe configured close to and below scaffolding, in close proximity to the Power Generation Building, in the area immediately east of the two approximately 115 foot tall Heat Recovery Steam Generators (HRSGs) and well below the tops of all of those structures; the failure to eliminate open flame ignition sources, including but not limited to propane heaters; construction work occurring during the gas blow process; individuals other than those essential to conducting the gas blows working in the area during the gas blow process; and the inability to readily control the amount of gas and pressure flowing through the main gas fuel line. On February 7, 2010, employees were exposed to serious or fatal impact and other injuries from an explosion hazard created when a large amount of natural gas was blown at high velocity through CT#2 Main Knockout Drum Vent Pipe (561-TNK-2002) into the area immediately east of HRSG number 2 and close to buildings, scaffolding, partially enclosed work areas, and other structures that were adjacent to the Power Generation Building in which employees worked and in or around in which open flame ignition sources, including but not limited to propane heaters, existed, construction work was occurring, and numerous employees non-essential to conducting the gas blow were working. When natural gas is chosen for this method of cleaning gas line pipes, feasible means of abatement to eliminate or materially reduce the hazard are to ensure that the vent pipe is positioned vertically and above the Power Generation Building and all other nearby structures, or horizontally to a location away from structures that could inhibit the adequate dispersal of the gas; ensure that any and all ignition sources are eliminated; ensure that any and all construction activity ceases during the gas blow process; ensure that all workers other than those essential to conducting the gas blows are removed from the building and area around which the gas blows are occurring; and ensure the use of devices to control the amount and pressure of gas vented, such as a fast closing pipe shut-off valve and a gas pressure control valve.




Citation 2 Item 4 Type of Violation: Willful Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm in that the method used to clean the 561 main fuel gas line pipes - blowing natural gas through them at high velocity - was not implemented in such a way as to protect employees from the hazard of an explosion caused by venting large amounts of natural gas into areas where it could accumulate and where, or in close proximity to where, ignition sources existed. The following conditions and practices contributed to the existence of this hazard: the vent pipe configured close to and below scaffolding, in close proximity to the Power Generation Building, in the area immediately east of the two approximately 115 foot tall Heat Recovery Steam Generators (HRSGs) and well below the tops of all of those structures; the failure to eliminate open flame ignition sources, including but not limited to propane heaters; construction work occurring during the gas blow process; individuals other than those essential to conducting the gas blows working in the area during the gas blow process; and the inability to readily control the amount of gas and pressure flowing through the main gas fuel line. On February 7, 2010, employees were exposed to serious or fatal impact and other injuries from an explosion hazard created when a large amount of natural gas was blown at high velocity through CT#2 Pilot Gas Filter Separator "A" Vent Pipe (561- SEP-2000A) into the area immediately east of HRSG number 2 and close to buildings, scaffolding, partially enclosed work areas, and other structures that were adjacent to the Power Generation Building in which employees worked and in or around in which open flame ignition sources, including but not limited to propane heaters, existed, construction work was occurring, and numerous employees non-essential to conducting the gas blow were working. When natural gas is chosen for this method of cleaning gas line pipes, feasible means of abatement to eliminate or materially reduce the hazard are to ensure that the vent pipe is positioned vertically and above the Power Generation Building and all other nearby structures, or horizontally to a location away from structures that could inhibit the adequate dispersal of the gas; ensure that any and all ignition sources are eliminated; ensure that any and all construction activity ceases during the gas blow process; ensure that all workers other than those essential to conducting the gas blows are removed from the building and area around which the gas blows are occurring; and ensure the use of devices to control the amount and pressure of gas vented, such as a fast closing pipe shut-off valve and gas pressure control valve. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM




Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 5 Type of Violation: Willful 29 CFR 1926.20(b)(2): The employer did not initiate and maintain a safety program which provides for frequent and regular inspections of jobsites, materials, and equipment to be made by a competent person (i.e., a person who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has the authority to take prompt corrective measures to eliminate them): a.Site - A competent person did not conduct frequent and regular inspections of the jobsite, materials and

equipment as required. ABATEMENT NOTE: A "competent person" means one who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and which has authorization to take prompt corrective measures to eliminate them. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 6 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct Employee #1 in the recognition and avoidance of

hazards related to gas blow operations. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 7 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct Employee #2 in the recognition and avoidance of

hazards related to gas blow operations. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





hazards related to gas blow operations. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 9 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct Employee #4 in the recognition and avoidance of

hazards related to gas blow operations. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





hazards related to gas blow operations. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 11 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of

Keystone Construction and Maintenance was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Keystone Construction and Maintenance have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 12 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of

Bluewater Energy Services was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Bluewater Energy Services have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





United Anco Services was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of United Anco Services have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Instrument Sciences and Technology was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Instrument Sciences and Technology have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Coverflex Manufacturing Inc. was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Coverflex Manufacturing Inc. have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 16 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of Api

Group Inc. was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Api Group Inc. have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 17 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of Ducci

Electrical Contractors, Inc. was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Ducci Electrical Contractors, Inc. have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 18 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of North

American Energy Services (NAES) was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of North American Energy Services (NAES) have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Siemens Energy was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Siemens Energy have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Smedley Crane was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Smedley Crane have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Tucker Mechanical was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Tucker Mechanical have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Worley Parsons was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Worley Parsons have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 23 Type of Violation: Willful 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of Team

Industrial was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Team Industrial have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Securitas was instructed in the recognition and avoidance of hazards related to gas blow operations. NOTE: For penalty purposes, the exposed employees of Securitas have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00





Contech Technical Services Co. was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Contech Technical Services Co. have been administratively combined into a single citation. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 26 Type of Violation: Willful 29 CFR 1926.352(c): The employer did not ensure that welding, cutting and heating was not performed where the application of flammable paints, or the presence of other flammable compounds, or heavy dust concentrations created a hazard. a.Site - Welding, cutting and heating were performed where flammable compounds created a hazard. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 27 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Between HRSG #1 and HRSG #2 - On February 7, 2010, the Wacker Neuson Ground Heater was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 28 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.North Wall near Column B2 - On February 7, 2010, the Dryco heater, number 52-13, was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 29 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.South Wall near Column G2 - On February 7, 2010, the Dryco heater, number 51-03, was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 30 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Subgrid CC+ near Column B6 - On February 7, 2010, the Dryco heater, number 52-14, was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 31 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-2/D-3 near Column G6 - On February 7, 2010, the Dryco heater, number 52-10, was not used as





Citation 2 Item 32 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D3 south of Column B8 - On February 7, 2010, the Dryco heater, number 52-13, was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 33 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.North Wall on Column B1 - On February 7, 2010, the Brasch Electric heater was not used as instructed by its

listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 34 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.On Column D1 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling or

certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 35 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 on Column G9 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,

labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 36 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.On Column G1 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling or

certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 37 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-2/D-3 on Column G5 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,





Citation 2 Item 38 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 on Column B8 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,

labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 39 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 on Column B9 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,





Citation 2 Item 40 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-2/D-3 on Column G4 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,

labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 41 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.On Column G1 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling or

certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 42 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 on Column G8 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,

labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 43 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Subgrid A - On February 7, 2010, the Miller IV Express Welder was not used as instructed by its listing, labeling

or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 44 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3, north side of Column G8 - On February 7, 2010, the temporary electric breaker panel SE1 was not used

as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 45 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Subgrid A Column C4 - On February 7, 2010, the temporary electrical breaker panel NW1 was not used as





Citation 2 Item 46 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 southwest of Column C9 - On February 7, 2010, temporary electrical breaker panel NE1A was not used

as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 47 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-2/D-3 Subgrid j-k - On February 7, 2010, the temporary circuit breaker panel SW1 was not used as





Citation 2 Item 48 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 west side between Columns D9 and E9 - On February 7, 2010, the Heat Stress Unit C121 was not used

as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 49 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 west side between Columns D9 and E9 - On February 7, 2010, the Heat Stress Units C254R, C123 and

C167 were not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 50 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grids D-2/D-3 Subgrid I - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 51 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 northwest side of Column C9 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not

used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 52 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grids D-2/D-3 Subgrid K - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 53 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grids D-2/D-3 near Column F6 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not used as





Citation 2 Item 54 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grids D-2/D-3 Subgrid K - On February 7, 2010, the FM Mafco KVA power distribution panel was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 55 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grids D-2/D-3 near Column G6 - On February 7, 2010, the 25 KVA Power Distribution Panel was not used as





Citation 2 Item 56 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 First Floor CG13 and CG14 - On February 7, 2010, the Dryco 51-01 heater was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 57 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4, First Floor between CG13 and CG14 - On February 7, 2010, the Brasch heater was not used as





Citation 2 Item 58 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4, First Floor between CG9 and CG10 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was

not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 59 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4, First Floor between CG10 and CG11 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was

not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 60 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 First Floor bwteen CG12 and CG13 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was

not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 61 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D4 Column G10 - On February 7, 2010, the Brasch electric heater was not used as instructed by its listing,





Citation 2 Item 62 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 Column G12 - On February 7, 2010, the Brasch electric heater was not used as instructed by its listing,

labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 63 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2, 5th Level East Side HRSG #1 - On February 7, 2010, the Heat Stress Unit C161D was not used as





Citation 2 Item 64 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2, 5th Level East Side HRSG #1 - On February 7, 2010, the Heat Stress Unit C126 was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 65 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2 along West Side HRSG #1 - On February 7, 2010, Heat Stress Unit C162 was not used as instructed by

its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 66 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2 Along west side of HRSG #1 - On February 7, 2010, the Heat Stress Unit #241 was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 67 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2 3rd Level East/West Mezzanine - On February 7, 2010, Miller Mark VIII-2 8 pack welder was not used

as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 68 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 between CG14 and CG15 - On February 7, 2010, the Red Arc EX300 welders were not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 69 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 3rd Floor between CG9 and CG10 - On February 7, 2010, Miller Mark VIII-2 8 pack welder was not





Citation 2 Item 70 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 3rd Floor between CG11 and CG12 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was

not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 71 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 3rd Floor between CG9 and CG10 - On February 7, 2010, the 25 KVA power distribution panel was not





Citation 2 Item 72 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 near Column C15 - On February 7, 2010, temporary circuit breaker panel NE1B was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 73 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2 Southeast of HRSG #1 - On February 7, 2010, temporary circuit breaker panel #1 was not used as





Citation 2 Item 74 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 between Columns CG14 and CG15 - On February 7, 2010, the Brasch Heater was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 75 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 Column F15 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling

or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 76 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 2nd Floor Column C15 - On February 7, 2010, the Brasch heater was not used as instructed by its

listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 77 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2 2nd Floor Column E15 - On February 7, 2010, the Brasch heater was not used as instructed by its

listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 78 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 2nd Floor Column G10 - On February 7, 2010, the Brasch heater was not used as instructed by its

listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 79 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 3rd Column G12 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,





Citation 2 Item 80 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 3rd Floor Column D15 - On February 7, 2010, the Brasch heater was not used as instructed by its

listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 81 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 3rd Floor Column F15 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,





Citation 2 Item 82 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-5 Administration Bldg Garage on Column - On February 7, 2010, the Brasch heater (#1) was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 83 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-5 Administration Bldg Garage on Column - On February 7, 2010, the Brasch heater (#2) was not used as





Citation 2 Item 84 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 Column G7 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling

or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 85 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-4 Ground Level South Exterior Wall of Power Generation Bldg - On February 7, 2010, temporary circuit

breaker panel #4 was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 86 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid C-3, Ground Level, North Side of Power Generation Bldg - On February 7, 2010, the temporary power

distribution shed ("North Shack") was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 87 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid F-4, Ground Level, next to South Side of DI Water Treatment Bldg - On February 7, 2010, the temporary

power distribution shed ("South Shack") was not used as instructed by its listing, labeling or certification.





Citation 2 Item 88 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-5, Ground Level, next to North Side DI Water Treatment Bldg - On February 7, 2010, the temporary

circuit breaker panel (transformer) for the Keystone trailer was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 89 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-4 Ground Level West Side of Water Treatment Bldg - On February 7, 2010, the temporary circuit breaker

panel #3 was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 90 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, SE of HRSG #2 - On February 7, 2010, the temporary circuit breaker panel #2 was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 91 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-4 3rd Level East/West Mezzanine - On February 7, 2010, the 25 KVA power distribution panel #1 was not





Citation 2 Item 92 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2 5th Level East Side HRSG #1 - On February 7, 2010, the DP-90 25 KVA power distribution panel was

not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 93 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 HRSG #2 Feedwater Pump Bldg - On February 7, 2010, the FM Mafco 25 KVA power distribution

panel #15 was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 94 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 East Side HRSG #2, 5th Level East/West Mezzanine - On February 7, 2010, the FM Mafco 25 KVA

power distribution panel #0036335 was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 95 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, 3rd Level, North/South Mezzanine, East Side - On February 7, 2010, the FM Mafco 25 KVA power

distribution panel #0042385 was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 96 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-3 near Column G7 - On February 7, 2010, the FM Mafco 25 KVA power distribution panel #15 was not

used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 97 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not





Citation 2 Item 98 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n

010638) was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 99 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n

756043) was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 100 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-4 3rd Level, East/West Mezzanine - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not

used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 101 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, 3rd Level, East/West Mezzanine - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not





Citation 2 Item 102 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, 3rd Level, East/West Mezzanine - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n

383582) was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 103 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, 5th Level, East Side HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n





Citation 2 Item 104 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n

756047) was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 105 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2, 5th Level, East Side of HRSG #1 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n





Citation 2 Item 106 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, 3rd Level North/South Mezzanine, East Side of HRSG #2 - On February 7, 2010, the Miller Mark VIII-

2 8 pack welder (s/n 242861) was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 107 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 3rd Level North/South Mezzanine, East Side HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8

pack welder was not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00




Citation 2 Item 108 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-2 5th Level East Side HRSG #1 - On February 7, 2010, the DP-90 25 KVA power distribution panel was

not used as instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 109 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-4 3rd Level East/West Mezzanine - On February 7, 2010, Heat Stress Unit C128 was not used as





Citation 2 Item 110 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-4 3rd Level East/West Mezzanine - On February 7, 2010, the Heat Stress Unit C134 was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 111 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-4, 3rd Level, East/West Mezzanine - On February 7, 2010, Heat Stress Unit 227 was not used as instructed





Citation 2 Item 112 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 HRSG Feed Water Pump Bldg - On February 7, 2010, the Heat Stress Unit #1 was not used as instructed

by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 113 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, 5th Level, East Side HRSG #2 - On February 7, 2010, Heat Stress Unit C121 was not used as instructed





Citation 2 Item 114 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3, 5th Level, North/South Mezzanine - On February 7, 2010, Heat Stress Unit C119 was not used as

instructed by its listing, labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 Citation 2 Item 115 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 Under HRSG #2 - On February 7, 2010, Heat Stress Unit C142 was not used as instructed by its listing,





Citation 2 Item 116 Type of Violation: Willful 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid E-3 HRSG Feedwater Pump Bldg. - On February 7, 2010, the Heat Stress Unit #2 was not used as instructed





Citation 2 Item 117 Type of Violation: Willful 29 CFR 1926.501(b)(1): Each employee on a walking/working surface with an unprotected side or edge which was 6 feet or more above a lower level was not protected from falling by use of guardrail systems, safety net systems, or personal fall arrest systems: a.Power Generation Building: Employees who were working on the top of an electrical cabinet were exposed to

fall hazards of approximately 8 feet. b.Site - Employees who were working within HRSG #1 knockout tank sump area were not protected from falls. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 70000.00 __________________________________________________ Robert W. Kowalski

Area Director




To: Inspection Number: 314295460 O&G Industries Inc. Inspection Date(s): 02/07/2010-08/02/2010 and its successors Issuance Date: 08/03/2010 112 Wall Street Torrington, CT 06790



Citation and Notification of Penalty Page 1 of 10 OSHA-2(Rev. 6/93)




See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities. Citation and Notification of Penalty Page 5 of 10 OSHA-2 (Rev. 9/93)

Citation 1 Item 1 Type of Violation: Serious 29 CFR 1910.1200(e)(1)(i): The written hazard communication program did not include an updated list of the hazardous chemicals known to be present using an identity that was referenced on the appropriate material safety data sheet: Jobsite: The hazard communication program did not contain a current list of hazardous chemicals including natural gas known to be present and include an identity that was referenced on the material safety data sheets. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 2 Type of Violation: Serious 29 CFR 1910.1200(e)(2)(i) as referenced by 29 CFR 1926.59: The employer's hazard communication program did not include methods the employer will use to provide other employers with a copy of the material safety data sheet, or to make it available at a central location in the workplace, for each hazardous chemical the other employers employees could be exposed to while working: a.Site - The hazard communication program did not include methods the employer would use to provide other

employers onsite with access to the material safety data sheets. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 3 Type of Violation: Serious 29 CFR 1910.1200(e)(2)(ii) as referenced by 29 CFR 1926.59: The employer's hazard communication program did not include methods the employer will use to inform the other employer(s) of any precautionary measures that need to be taken to protect employees during the workplace's normal operating conditions and in foreseeable emergencies: a.Site - The hazard communication program did not include methods the employer would use to inform other

employers of any precautionary measures that need to be taken to protect employees during the workplaces normal operating conditions and in foreseeable emergencies.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 4 Type of Violation: Serious 29 CFR 1910.1200(g)(8) as referenced by 29 CFR 1926.59: The employer did not maintain copies of the required material safety data sheets for each hazardous chemical in the workplace: a.Site - A material safety data sheet for natural gas was not maintained at the jobsite. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 5 Type of Violation: Serious 29 CFR 1910.1200(h)(3)(i): The employee training did not include the methods and observations used to detect the presence or release of a hazardous chemical in the work area: Jobsite: Employee training was not conducted in the methods and observations to detect the presence or release of natural gas. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 6 Type of Violation: Serious 29 CFR 1910.1200(h)(3)(ii): Employee training did not include the physical and health hazards of the chemicals in the work area: Jobsite: Employees did not receive training in the physical and health hazards of hazardous chemicals such as but not limited to natural gas. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 7 Type of Violation: Serious 29 CFR 1910.1200(h)(3)(iii): Employee training did not include the measures employees can take to protect themselves from chemical hazards, including specific procedures the employer had implemented to protect employees from exposure to hazardous chemicals: Jobsite: Employee training was not conducted to include the measures employees shall take to protect themselves from chemical hazards, including specific procedures, to protect employees from exposure and hazards associated with products and chemicals such as but not limited to natural gas. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 2 Item 1 Type of Violation: Other 29 CFR 1904.32(a)(4): The company executive who certifies the OSHA 300 log, was not an approved official: Location: Jobsite, 1349 River Road, Middletown CT The employer failed to ensure that an approved company executive reviewed the 2009 OSHA 300A's for accuracy and signature. Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 1000.00 Citation 2 Item 2 Type of Violation: Other 29 CFR 1904.40(a): Copies of records kept under Part 1904 requested by an authorized government representative were not provided within four (4) business hours Location: Jobsite, 1349 River Road, Middletown CT The employer failed to provide the OSHA 300 logs for the year 2008 when requested. Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 1000.00




Citation 2 Item 3 Type of Violation: Other 29 CFR 1904.40(a): Copies of records kept under Part 1904 requested by an authorized government representative were not provided within four (4) business hours Location: Jobsite, 1349 River Road, Middletown CT The employer failed to provide the OSHA 300 logs for 2009 when requested. Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 1000.00 __________________________________________________

Robert W. Kowalski Area Director




To: Inspection Number: 109179994 Ducci Electrical Contracors, Inc. Inspection Date(s): 02/26/2010-08/02/2010 and its successors Issuance Date: 08/03/2010 427 Goshen Road Torrington, CT 06790






Issuance Date: 08/03/2010 Citation and Notification of Penalty Company Name: Ducci Electrical Contracors, Inc. Inspection Site: 1349 River Road, Middletown, CT 06450


Citation 1 Item 1 Type of Violation: Serious 29 CFR 1926.20(b)(2): The employer did not initiate and maintain a safety program which provides for frequent and regular inspections of jobsites, materials, and equipment to be made by a competent person (i.e., a person who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has the authority to take prompt corrective measures to eliminate them): a.Site - A competent person did not conduct frequent and regular inspections of the jobsite, materials and equipment as

required. ABATEMENT NOTE: A "competent person" means one who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and which has authorization to take prompt corrective measures to eliminate them. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 2 Type of Violation: Serious 29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other exposure to illness or injury: a.Site - On or about February 7, 2010, O&G failed to instruct Employee #1 in the recognition and avoidance of

hazards related to gas blow operations. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 3 Type of Violation: Serious 29 CFR 1926.65(q)(1): The employer did not develop and implement an emergency response plan to handle anticipated emergencies prior to the commencement of emergency response operations. Jobsite: An emergency response plan was not developed and implemented to handle anticipated emergency incidents. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 4 Type of Violation: Serious 29 CFR 1926.150(e)(1): An alarm system was not established by the employer whereby employees on the site could be alerted for emergencies: Jobsite: The employer failed to develop an alarm system that was distinguishable from other alarms used at the jobsite to alert employees of emergencies. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 5 Type of Violation: Serious 29 CFR 1926.150(e)(2): The alarm code or reporting instructions were not conspicuously posted at phones or at employee entrances: Jobsite: The employer failed to conspicuously post fire alarm codes at the jobsite. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00




Citation 1 Item 6 Type of Violation: Serious 29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification: a.Grid D-4 Column G12 - On February 7, 2010, the Brasch electric heater was not used as instructed by its listing,

labeling or certification. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 __________________________________________________ Robert W. Kowalski

Area Director




To: Inspection Number: 314295429 Ducci Electrical Contractors, Inc. Inspection Date(s): 02/26/2010-08/02/2010 and its successors Issuance Date: 08/03/2010 427 Goshen Road Torrington, CT 06790






Issuance Date: 08/03/2010 Citation and Notification of Penalty Company Name: Ducci Electrical Contractors, Inc. Inspection Site: 1349 River Road, Middletown, CT 06450


Citation 1 Item 1 Type of Violation: Serious 29 CFR 1910.1200(h)(3)(i): The employee training did not include the methods and observations used to detect the presence or release of a hazardous chemical in the work area: Jobsite: Employee training was not conducted in the methods and observations to detect the presence or release of natural gas. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 Citation 1 Item 2 Type of Violation: Serious 29 CFR 1910.1200(h)(3)(ii): Employee training did not include the physical and health hazards of the chemicals in the work area: Jobsite: Employees did not receive training in the physical and health hazards of hazardous chemicals such as but not limited to natural gas. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00


Issuance Date: 08/03/2010 Citation and Notification of Penalty Company Name: Ducci Electrical Contractors, Inc. Inspection Site: 1349 River Road, Middletown, CT 06450


Citation 1 Item 3 Type of Violation: Serious 29 CFR 1910.1200(h)(3)(iii): Employee training did not include the measures employees can take to protect themselves from chemical hazards, including specific procedures the employer had implemented to protect employees from exposure to hazardous chemicals: Jobsite: Employee training was not conducted to include the measures employees shall take to protect themselves from chemical hazards, including specific procedures, to protect employees from exposure and hazards associated with products and chemicals such as but not limited to natural gas. ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM Date By Which Violation Must be Abated: 08/09/2010 Proposed Penalty: $ 7000.00 __________________________________________________ Robert W. Kowalski

Area Director

osha citations against o&g and ducci electric

Documents