over view on section mill

8/7/2019 Over view on section mill

1/137

y Plant layout.

y Single line diagram.

y SINAMICS drive.

y Automation levels.

y Automation layout.


2/137


3/137


4/137


5/137


6/137


7/137


8/137


9/137


10/137


11/137


12/137


13/137


14/137


15/137


16/137


17/137


18/137


19/137


20/137


21/137


22/137


23/137


24/137


25/137


26/137


27/137


28/137


29/137


30/137


31/137


32/137


33/137


34/137


35/137


36/137


37/137


38/137


39/137


40/137


41/137


42/137


43/137


44/137


45/137


46/137


47/137


48/137


49/137


50/137


51/137


52/137


53/137


54/137


55/137


56/137


57/137


58/137

CU: Control Unit.

TM card: terminal module for I/O (motor fan Fbk, drivefan Fbk).

SMC card: sensor module cabinet for encoder Fbk.

y Drive to PLCstatus word. Like (current/ alarms /

speed ref.).

y every motor connect to CU had an individual speed

control, may many motor groups connected to same CU,but max. number of motor groups connected = 4 groups.

y PLC to Drive . Command word.y Drive to PLC.. Status word


59/137


60/137


61/137


62/137


63/137


64/137


65/137


66/137


67/137


68/137


69/137


70/137


71/137


72/137


73/137


74/137


75/137


76/137


77/137


78/137


79/137


80/137


81/137


82/137


83/137

y An optional operator panel for operating, monitoring, and commissioning purposes

y is available. It has the following features:

y Leds for displaying the operational statuses

y Help function describing causes of and remedies for faults and alarms

y Keypad for controlling drives during operation

y LOCAL/REMOTE switchover for selecting the control terminal (master control assigned tooperator panel or customer terminal block / PROFIBUS)

y Numeric keypad for entering set point or parameter values

y Function keys for prompted navigation through the menus

y Two-stage security concept to protect against accidental or unauthorized

y changes to settings

y Degree of protection IP 54 (when installed)


84/137


85/137


86/137

y STARTER offers two alternative methods for creating a

drive project:

1- OFFLINE: you use a Wizard to configure andparameterize the drive unit.

2-ONLINE: you use a Wizard to load the existing driveunit configuration and parameterization to STARTER.

y If you have created or loaded a project in STARTER,you can operate the drive via the STARTER controlpanel.


87/137


88/137


89/137


90/137


91/137


92/137


93/137


94/137

y Level 0: actuators, motors, sensors, encoders and drive.

y Level 1:

- PLC, relative S/W - HMI, relative S/W FDA, relativeS/W , technological maintenance.

y Level 2: OWS operator work station server PC in electricroom with 4 hard disk3 backup hard disks. PWSprocess work station preparation data like costumer name

& data for size .y

y Level 3: product catalogs yearly reports.


95/137


96/137


97/137


98/137


99/137

TWS


100/137

TWS


101/137


102/137


103/137


104/137


105/137


106/137


107/137


108/137


109/137


110/137


111/137


112/137


113/137


114/137


115/137


116/137


117/137


118/137


119/137


120/137


121/137


122/137


123/137


124/137


125/137


126/137


127/137


128/137


129/137


130/137


131/137


132/137

y Insulation protection relay.

y Stands (groove with absolute encoder , gap with absolute encoder and speed feedbackincremental encoder").

y DOM: Danieli (O) Horizontal Mill. &

DVM: Danieli Vertical Mill. &

DCM: Danieli Control Mill. (H/V). &

DUM: Danieli Universal Mill.

y kicker driven by inverter.

y FDA : fast data analysis (like logger).

y Straightener entry R.T. (start of cold area).

y Two Bundles packing in parallel mode.


133/137


134/137


135/137


136/137


137/137

over view on section mill

Documents