Owner's Manual andInstallation Instructions

Galaxy TM

One-SpeedAUTOMATIC WASHERS

IMPORTANT:

Read and follow all safetyand operating instructionsbefore first use of this product.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.Sears Canada Inc,, Toronto, Ontario, Canada M5B 2B8

www.sears.comwww.sears.ca

8530580 PRINTED IN U.S.A. 3/02

BEFORE USING 2

GALAXY AUTOMATIC WASHER WARRANTY 3

WASHER SAFETY ........... 4

INSTALLATION REQUIREMENTS 6

INSTALLATION INSTRUCTIONS ...... 10

WASHER USE .......... 14

LAUNDRY TIPS ......... 20

WASHER CARE ........ 22

TROUBLESHOOTING ...... 23

WE SERVICE WHAT WE SELL 27

Please read this manual. It will helpyou install and operate your new Galaxywasher in the most economical way,

For more information about the care

and operation of Galaxy appliances, callyour nearest Sears store, You will needthe complete model and serial numberswhen requesting information. Your wash-er's model and serial numbers are locat-ed on the Model and Serial NumberPlate.

_d Serial

Number Plate

Use the space below to record the modelnumber and serial number of your newGalaxy washer.

Model No.

Serial No.

Date of Purchase

Keep this book and your SearsSalescheck (receipt) in a safe place forfuture reference.

90-DAY WARRANTYON MECHANICAL ANDELECTRICAL PARTS

For ninety days from the date of)urchase, when the washer is installed

and operated in accordance with theinstructions in the Owner's Manual, Searswill repair or replace any mechanical orelectrical parts in this washer, if defectivein material or workmanship.

LIMITED 2-YEAR WARRANTYON GEARCASE PARTS*

After ninety days and until two years fromthe date of purchase, Sears will furnishreplacement parts for any defectivegearcase parts. You will be charged forlabor.

LIMITED 5-YEAR WARRANTYON PLASTIC TUB*After ninety days and until five yearsfrom date of purchase, Sears will furnisha replacement plastic tub for any plastictub which is defective in material or work-manship. You will be charged for Iabon

If the washer is subjected to other than private family use, the above warrantycoverage is effective for only 90 days.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEARESTSEARS SERVICE CENTER IN THE UNITED STATES OR CANADA.

This warranty applies only while this product is in use in the United States orCanada. This warranty gives you specific legal rights, and you may have other rightswhich vary from state to state or province to province.

Sears Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 U.S.A.

Sears Canada Inc., Toronto, Ontario M5B 2B8

*In Canada, a different warranty may apply. In the U.S., for Sears warranty information or to con-tact a Sears Service Center, please reference the service numbers on the back page of thismanual.

Your safety and the safety of others are very important.

We have provided many importantsafety messages in this manual andon your appliance. Always read and obey all safety messages.

This is the safety alertsymbol. This symbol alertsyou topotential hazards that can kill or hurt you and others.All safety messages willfollowthe safety alert symboland either the word "DANGER" or "WARNING."These words mean:

You can be killed or seriouslyInjured If you don't Immedlstel¥follow instructions.

You can be killed or seriouslyinjured if you don't followinstructions.

All safety messages will tell you what the potential hazard is, tell you howto reduce the chance of injury,and tellyou what can happen if theinstructionsare notfollowed,

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to personswhen using your washer, follow basic precautions, including the following:

• Read all instructions before usingthe washer.

• Do not wash articles that have been

previously cleaned in, washed in,soaked in, or spotted with gasoline,dry-cleaning solvents, otherflammable or explosive substancesas they give off vapors that couldignite or explode.

• Do not add gasoline, dry-cleaningsolvents, or other flammable orexplosive substances to the washwater. These substances give offvapors that could ignite or explode.

• Under certain conditions, hydrogengas may be produced in a hot watersystem that has not been used for 2weeks or more. HYDROGEN GAS ISEXPLOSIVE. If the hot water systemhas not been used for such a period,before using a washing machine, turnon all hot water faucets and let thewater flow from each for several

minutes. This will release anyaccumulated hydrogen gas. As thegas is flammable, do not smoke oruse an open flame during this time.

• Do not allow children to play on or inthe washer. Close supervision of chil-dren is necessary when the washer isused near children.

• Before the washer is removed fromservice or discarded, remove the dooror lid.

• Do not reach into the washer if the

drum, tub or agitator is moving.• Do not install or store this washer where

it will be exposed to the weathen

• Do not tamper with controls.

• Do not repair or replace any part of thewasher or attempt any servicing unlessspecifically recommended in theOwner's Manual or in published user-repair instructions that you understandand have the skills to carry out.

• See "Electrical Requirements" forgrounding instructions.

SAVE THESE INSTRUCTIONS

Tools and PartsAssemble the necessary tools andsupplies before beginning the washerinstallation. The parts supplied are in thewasher basket.

Tools needed for connecting the drainhose and water inlet hoses:

• Pliers that open to f_G in, (3.95 cm)• Flashlight (optional)Parts supplied:

4 5

1, Drain hose2, Silver, double-wire hose clamp

(for the bottom of the drain hose)3. Yellow, single-wire hose clamp

(for the top of the drain hose)4. Water inlet hoses (2)5. Flat water inlet hose washers (4)

Tools needed for securing the drainhose and leveling the washer:

• Open end wrench _6 in, (1.43 cm)• Level• Wood block

• Ruler or measuring tapeParts supplied:

I 2

1. Si_ipping strap with fastener2 Front leveling feet with nuts (2)

Alternate Parts

Parts listed are available from your localSears store or Sears Service Center.Please reference the service numberslocated on the back page of this manual

If you have: You will need to buy:

Laundry tub or Sump pump system (ifstandpipe not already available)taller than 96in. (2.4 m)

1 in. (2.5 cm) 2 in. (5 cm) diameter todiameter 1 in. (2.5 cm) diameterstandpipe standpipe adapter, Part

No. 3363920

Overhead Standard 20 gal (76 L)sewer 39 in. (99 cm) tall drain

tub or utility sink, sumppump and connectors(available from localplumbing suppliers)

Floor drain Siphon break, PartNumber 285320; addi-tional drain hose, PartNumber 3357090 andconnector kit, PartNumber 285442

Water faucets 2 longer wafer fill hoses:beyond reach 6 ft (1.8 m) Part Numberof fill hoses 76314, 10 ft (3.0 m) Part

Number 350008

Drain hose too Drain hose, Part No.short 388423 and hose kit,

Part No. 285442

Drain hose Hose kit, Part No.that is too long 285442

Lint clogged Drain protector, Part No.drain 367031

Location Requirements

Selecting the proper location for yourwasher improves performance and mini-mizes noise and possible washer "walk."Your washer can be installed in a base-ment, laundry room, closet, or recessedarea. (See "Drain System.")

Proper installation is your responsibility.You will need:

• A water heater set to deliver 120°F(49°C) water to the washer.

• A grounded electrical outlet locatedwithin 4 ft (1.2 m) of where the powercord is attached to the back of thewasher. (See "Electrical Requirements.")

• Hot and cold water faucets located with-in 4 ft (1.2 m) of the hot and cold waterfill valves, and water pressure of 5-100psi (34.5-689.6 kPa). Washers withtriple dispensers require 20-100 psi(138.0-689.6 kPa) for best performance.

• A level floor with a maximum slope of1 in. (2.5 cm) under entire washer.Installing the washer on carpeting is notrecommended.

• A sturdy floor to support the washerweight (washer, water and load) of 315Ibs (143 kgs).

Do not store or operate your washer intemperatures at or below 32°F (0°C).Some water can remain in the washer andcan cause damage in low temperatures.See "Washer Care" for winterizing infor-mation.

Recessed area or closet installationThe dimensions shown are for the rec-ommended spacing allowed, except thecloset door ventilation openings. Thedimensions shown for the closet doorventilation openings are the minimumrequired.

m

1 2

lll,,z

3

1. Front view2. Side view& Closet door with vents

• Additional spacing should be consid*ered for ease of installation and ser-vicing.

• Additional clearances may be requiredfor wall, door and floor moldings.

• Additional spacing of 1 in. (2.5 cm) onall sides of the washer is recommend*ed to reduce noise transfen

• If a closet door is installed, the mini-mum air openings in the top and bot-tom of the door are required.Louvered doors with air openings inthe top and bottom are acceptable.

• Companion appliance spacing shouldalso be considered.

Drain SystemThe washer can be installed using thestandpipe drain system (floor or wall), thelaundry tub drain system, or the floordrain system. Select the drain hose instal-lation method you need. (See "AlternateParts.")

1 2

Standpipe drain system - wall or floor(view 1 & 2)

The standpipe drain requires a minimumdiameter standpipe of 2 in. (5 cm). Theminimum carry*away capacity can be noless than 17 gal. (64 L) per minute. A 2 in.(5 cm) diameter to 1 in. (2.5 cm) diameterstandpipe adapter kit is available. (See"Alternate Parts.")The top of the standpipe must be at least39 in. (99 cm) high and no higher than 96in. (2.4 m) from the bottom of the washer.

Floor drain system (view 2)The floor drain system requires a siphonbreak that may be purchased separately.(See "Alternate Parts.")

The siphon break must be a minimum of28 in. (71 cm) from the bottom of thewasher. Additional hoses might beneeded.

Electrical Requirements

Electrical Shock Hazard

Plug into a grounded3 prong outlet.

Do not remove ground prong.

Do not use an adapter.Do not use an extension cord.

Failure to follow theseinstructions can result indeath, fire, or electrical shock.

• A 120-volt, 60-Hz., AC-only, 15- or 20-ampere, fused electrical supply isrequired. Time-delay fuse or circuitbreaker is recommended. It is recom*mended that a separate circuit servingonly this appliance be provided.

• This washer is equipped with a powersupply cord having a 3 prong groundplug.

Laundry tub drain system (view 1)The laundry tub needs a minimum 20 gal.(76 L) capacity. The top of the laundry tubmust be at least 39 in, (99 cm) above thefloor and no higher than 96 in, (2.4 m)from the bottom of the washer.

• Tominimizepossibleshockhazard,thecordmustbepluggedintoamating,3prong,ground4ypeoutlet,groundedinaccordancewithlocalcodesandordi-nances.Ifamatingoutletisnotavail-able,it isthepersonalresponsibilityandobligationofthecustomertohavetheproperlygroundedoutletinstalledbyaqualifiedelectdcian.

• Ifcodespermitandaseparategroundwireisused,it isrecommendedthataqualifiedelectriciandeterminethatthegroundpathisadequate.

• Donotgroundtoagaspipe.• Checkwithaqualifiedelectricianifyou

arenotsurethewasherisproperlygrounded.

• Donothavea fuse in the neutral orground circuit.

1. 3 prong grounding plug2. 3 prong grounding-type outlet3. Ground prong4. Power supply cord

GROUNDINGINSTRUCTIONS

For a grounded, cord-connectedwasher:

This washer must be grounded. In theevent of a malfunction or breakdown,grounding will reduce the risk ofelectrical shock by providing a path ofleast resistance for electric current, Thiswasher is equipped with a cord havingan equipment-grounding conductor anda grounding plug, The plug must beplugged into an appropriate outlet thatis properly installed and grounded inaccordance with all local codes andordinances.

WARNING: Improper connection ofthe equipment-grounding conductor canresult in a risk of electric shock. Check

with a qualified electrician or service-man if you are in doubt as to whetherthe appliance is properly grounded.

Do not modify the plug provided withthe appliance - if it will not fit the oufielhave a proper outlet installed by a

qualified electrician,

For a permanently connectedwasher:This washer must be connected to agrounded metal, permanent wiringsystem, or an equipment groundingconductor must be run with the circuitconductors and connected to the

equipment-grounding terminal or lead

on the app ance.

Before You Start3, Cut the shipping strap about 16 in,

(40 cm) from plug end. Look for thewords "CUT HERE." Discard end withthe cotter pins. Slide remainder ofshipping strap from the power cord.You will use the remainder of theshipping strap later to secure thedrain hose.

• To prevent floor damage, set thewasher onto cardboard before movingacross floon

• Move the washer to within approxi-mately 3 ft (90 cm) of the final location.

Remove Shipping StrapRemoving the shipping strap is necessaryfor smooth operation, If the shipping strapis not removed, the washer will makeexcessive noise.

1. Do not cut yellow strap, Pull yellowstrap firmly, until completely removedfrom washer, Depending on yourmodel, there will be either two or threecotter pins on the end of the shippingstrap when it is pulled out of thewasher, The electrical plug is attachedto this shipping strap.

2, Pull firmly to remove the end of theshipping strap that remains pinned tothe back of the washer. This willrelease the rear self-leveling feet.

Connect Drain Hose

Proper connection of the drain hose willprotect your floors from damage due towater leakage, To prevent the drain hosefrom coming off or leaking, it must beinstalled per the following instructions.

IMPORTANT: To ensure proper installa-tion, this procedure must be followedexactly.

1, Check the drain hose to see if it isthe proper length.

2, Wet the inside of the straight end ofthe drain hose with tap water. DONOT USE ANY OTHER LUBRICANT.

3, Squeeze ears of silver, double-wireclamp with pliers to open. Placeclamp over the straight end of thedrain hose ¼ in. (6 mm) from the end.

1/4"

(6 rnm)

10

4, Open clamp. Twist hose back andforth while pushing down onto drainconnector at the bottom of the wash-er, Continue until hose contacts theribbed stop on the cabinet.

Y5, Place clamp over area marked

"CLAMR" Release clamp.

1/4"

1. Drain Hose2. Clamp3. Ribbed Stop4. Cabinet

For standpipe or laundry tub drainsystems:

1, Open yellow, single-wire clamp withpliers and slide over hooked end ofdrain hose to secure the rubber andcorrugated sections together.

• For floor drain installation, see kit num-ber required under "Alternate Parts."

1,

Connect the Inlet Hoses

Insert new flat washers (supplied) intoeach end of the inlet hoses. Firmlyseat the washers in the couplings.

1 2

1. Coupling2. Washer

Connect the inlet hoses to the waterfaucets

Make sure the washer basket is empty.

2. Attach the hose with the red couplingto the hot water faucet. Screw on cou-pling by hand until seated on thewasher.

3,

4,

Attach the hose with the blue couplingto the cold water faucet. Screw oncoupling by hand until seated on thewasher.

Using pliers, tighten the couplings withan additional two-thirds turn.

1. Hooked end2. Drain hose

2, Put hooked end of drain hose intolaundry tub or standpipe. Rotatehook to eliminate kinks.

To prevent drain water from goingback into the washer:

• Do not straighten hooked end of drainhose. Do not force excess drain hoseinto standpipe. Hose should besecure, but loose enough to provide agap of air.

• Do not lay excess drain hose in bot-tom of laundry tub.

NOTE: Do not overtighten. Damage tothe valves can result.

11

Clear the water lines

5, Run water through both faucets andinlet hoses, into a bucket or laundrytub, to get rid of particles in the waterlines that might clog the inlet valvescreens.

Connect the inlet hoses to the washer

6, Attach the hose with the red couplingto the HOT (bottom) inlet valve.Attaching the red coupling first makesit easier to tighten connection withpliers, Screw on coupling by handuntil seated on the washer. Using pli-ers, tighten the couplings with anadditional two-thirds turn.

NOTE: Do not overtighten. Damageto the valves can result.

_2

1. Cold water inlet valve (blue)2. Hot water inlet valve (red)

NOTE: The inlet valve may be on theright or the left side of the washer,depending on your model,

7, Attach the hose with the blue cou*piing to the COLD water (top) inletvalve, Screw on coupling by handuntil seated on the washer. Using pli-ers, tighten the couplings with anadditional two-thirds turn,

NOTE: Do not overtighten. Damageto the valves can result.

Check for leaks

8, Turn on the water faucets and checkfor leaks, A small amount of watermight enter the washer. You will drainthis later.

NOTE: Replace inlet hoses after 5years of use to reduce the risk of hosefailure, Record hose installation orreplacement dates for future reference.

12

• If you only connect one waterhose, you must cap off the remain*ing water inlet port.

• Periodically inspect and replacehoses if bulges, kinks, cuts, wear,or leaks are found.

Secure the Drain Hose

1. Drape the power cord over the console.

2. Remove any cardboard used to movewasher.

3. Locate the remaining piece of ship*ping strap (not the end with the cotterpins) from step 3 of "RemoveShipping Strap." Use it to wrap thedrain hose together with the laundrytub or standpipe, Push fastener intothe nearest hole in the shipping strap.

Remaining portion of Shipping Strap

4. Wrap the drain hose to the laundrytub leg or standpipe with the tie strap.(See illustration.)

If the washer faucets and the drainstandpipe are recessed, put thehooked end of the drain hose in thestandpipe. Tightly wrap the tie straparound the water inlet hoses and thedrain hose.

Level the WasherProperly leveling your washer preventsexcessive noise and vibration.

Install the front leveling feet

1. Prop up the front of the washer about4 in, (10,2 cm) with a wood block orsimilar object, The block needs tosupport the weight of the washer.

2. Screw the lock nut onto each foot towithin 1 in. (2.5 cm) of the base.

1"

(2.5 cm)

&

3. Screw the feet into the correct holesat the front corner of the washer untilthe nuts touch the washer.

NOTE: Do not tighten the nuts untilthe washer is level.

4. Tiltthewasherbackandremovethe 3.woodblock.Gentlylowerthewashertothefloor. 4.

5. Slidetofinallocation.6. Checkthelevelnessofthewasher

byplacingalevelonthetopedgesofthewasher;firstside-to-side,thenfront4o-back,

5.

6.

7.

Check to be sure you have all ofyour tools.

Check to be sure that the yellowshipping strap was removed from theback of the washer and used tosecure the drain hose.

Dispose/recycle all packagingmaterials.

Check to be sure the water faucetsare on.

Check for leaks around faucets andinlet hoses.

If the washer is not level, move thewasher out slightly, tip back, prop upthe front of the washer with the woodblock and adjust the feet up or downas necessary, Repeat this step untilwasher is level.

7. After the washer is in the final loca-tion and level, use a _Gin. (1.43 cm)open-end wrench to turn the nuts onthe feet tightly against the washercabinet.

If the nuts are not tight against thewasher cabinet, the washer mayvibrate.

8. Tilt the washer forward until the rearof the washer is at least 4 in, (10.2cm) off the floor, You may hear theself-adjusting rear feet click intoplace. Lower the washer to the floon

Complete Installation1. Check the electrical requirements, Be

sure that you have the correct electri-cal supply and the recommendedgrounding method. (See "ElectricalRequirements.")

2, Check to be sure all parts are nowinstalled. If there is an extra part, goback through the steps to see whichstep was skipped.

Electrical Shock Hazard

Plug into a grounded

3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow theseinstructions can result in

death, fire, or electrical shock.

8. Plug into a grounded 3 prong outlet,

9. Remove the protective film on theconsole and any tape remaining onthe washer,

10, Read "Washer Use."

11. To test your washer, measure half ofthe normal recommended amount ofpowdered or liquid detergent andpour it into the washer basket ordetergent dispenser (on some mod-els). Close the lid. Select any cycle,and then press START. Allow it tocomplete one whole cycle.

13

To get the maximum cleaning andfabric care from your washer, pleaseread and follow these instructions.

NOTE: The drawings in this section showthe basic features of all models coveredby this manual. Refer to the supplied"Feature Sheet" for your washer's particu-lar features.

Fire Hazard

Never place items in the washer

that are dampened with gasolineor other flammable fluids.

No washer can completelyremove oil.

Do not dry anything that has ever

had any type of oil on it (includingcooking oils).

Doing so can result in death,explosion, or fire.

WARNING: To reduce the risk of fire,

electric shock, or injury to persons, readthe IMPORTANT SAFETY INSTRUCTIONS

before operating this appliance.

14

STARTING YOUR WASHER

1, Add measured detergent directly intowasher basket. Then place a load ofsorted clothes in the washer.

2, Close washer lid.

3, Set WATER LEVEL Control I_ basedon the size of your wash load.

STOPPING/RESTARTINGYOUR WASHER

• To stop the washer at any time, pushthe Cycle Selector Control (Timer)knob O in.

• Pull the knob out to restart.

4, Push the Cycle Selector Control (Tim-er) knob O in and turn to the right.Set cycle and time according to thetype of fabric in the load.

5, Pull the Cycle Selector Control (Timer)knob O out. The dial will rotate as thecycle progresses. The knob willnot rotate.

15

SET WATER LEVEL CONTROL

This control gives you the flexibility tosave water when washing small loads,

Your washer lets you select a watersetting based on the size of yourwash load.

• For normal loads, start with a mediumload, Adjust up or down depending onyour load, Clothes should move freelyand roll toward the agitator.

• To change to a higher water levelsetting after the washer has started toagitate, turn the knob to the desired newsetting.

WASH/RINSE WATERTEMPERATURE

Your wash/rinse water temperature controlis part of the Cycle Selector Control(Timer) knob. All rinses are cold to saveenergy.• For a HOT water wash, select SUPER.

• For a WARM water wash, selectREGULAR.

• For a COLD water wash, select SHORT.

To select a different wash temperatureand cycle (time):

1, Push in the Cycle Selector Control(Timer) knob and turn clockwise to thedesired water temperature.

2, Pull out the Timer knob and allow theSMALL II LARGE washer to fill.

3, When the washer has filled, push in theTimer knob and turn to the desiredcycle (time).

4, Pull out the Timer knob.

SELECTING WATER TEMPERATURES

Wash WaterTemperature Suggested Fabrics Comments

HOT • Work clothes • Best cleaning for heavily soiled items111°F (44°C) • Sturdy whites/ • Removes oils, perspiration, greasy soilsor above colorfast pastels and stains

• Diapers • Prevents graying or yellowing

WARM • Dark/non-colorfast colors • Best for moderately soiled to lightly soiled items90°-110°F • Permanent press items • Safe for most fabric finishes(32°-43°C) • Nylon, polyester, acrylics, • Less fading and dye bleeding

silks, woolens • Reduces wrinkling• Knits/delicate fabrics

COLD* • Extra-sensitive coIors • Best for very lightly soiled items70°-90°F • Non-colorfast items • Saves hot water

(21°-32°C) • Hand washables

*In wash water tern eratures colder than 70°F (21°C), detergents do not dissolve well. Also,soils may be difficult to remove and some fabrics may retain wear wrinkles and haveincreased pilling - the formation of small lint-like balls on the surface of garments. Pilling isthe naturai result of wearing and washing of garments.

16

SETTING YOUR CYCLE

SELECTOR (TIMER) CONTROL• For sturdy or heavily soiled loads, use

SUPER.

• For moderately soiled loads, useREGULAR.

• For delicate or lightly soiled loads, useSHORT.

HEAVY DUTY

Use this cycle to get up to 14 minutes ofwash time. Wash combines fast speedagitation and fast spin speeds.

PERMANENT PRESS

The PERMANENT PRESS cycle includesa load cooling process that reduceswrinkling compared to other cycles.Use this cycle to get up to 10 minutes ofwash time. Wash combines fast speedagitation and fast spin speeds.

NOTE: When the timer reaches PAUSE,the washer will drain and pause for nomore than two minutes while some of

the wash water is replaced with rinsewater.

8HOflTCOU_I COLD

RINSE AND SPINWhen using extra detergent for heavilysoiled clothes, or washing special-careitems, you may find an extra rinse andspin is needed.

1. Set WATER LEVEL Control.

2. Set the Cycle Selector Control (Timer)knob to the RINSE setting.

3. Pull Cycle Selector Control(Timer) knob out to start washer.

PERMANENTPRESS

10 SUPI_ItOT/ COU)

I REGULARWNqM I COLD

SHORTCOLD/COLD

SPIN ONLY

A drain and spin may help shorten dryingtimes for some heavy fabrics or special-care items by removing excess water.

1. Set the Cycle Selector Control (Timer)knob to the SPIN setting.

2. Pull the Cycle Selector Control (Timer)knob out to start washer.

12

12

14

17

UNDERSTANDING WHAT HAPPENSDURING THE WASHER CYCLE

HEAVY DUTY PERMANENT PRESS

Fill to _ Fill toselected level selected level

Wash Washselected time selected time

Partial

Drain - Drainno spin

PauseSpin

• _ Fill for

Fill to cool downWselected level •

• Wash

Rinse

• _ Drain -

Drain - no spinno spin •

• Spin

Spin

• _ Fill toselected level

Off •

Rinse

Drain -no spin

Spin

Off

18

STRAIGHT VANE AGITATOR

This agitator is foundin Galaxy large capacitywashers. Its design iswell-suited to handleyour everyday loads.

UNDERSTANDING NORMALSOUNDS

Your new washer may make soundsthat your old one didn't. Because thesounds are unfamiliar, you may beconcerned about them.

The following describes some of thenormal sounds you may hear and whatcauses them.

During DrainThe rate that water is drained from yourwasher depends on your installation. Ifwater is drained quickly from the washer,you may hear air being pulled through thepump. This happens during the end ofdraining.

After Drain and Before SpinWhen the cycle changes from drainingto spinning, you may hear a noise as thegearcase shifts.

19

PREPARING CLOTHESFOR WASHING

Follow these recommendationsto help you prolong the life ofyour garments.

• Close zippers, snaps, and hooks toavoid snagging other items. Removepins, buckles, and other hard objectsto avoid scratching the washer interior.Remove non-washable trim andornaments.

• Empty pockets and turn theminside out.

• Turn down cuffs, brush away lintand dirt.

• Turn synthetic knits inside out toavoid pilling.

• Tie strings and sashes so they willnot tangle.

• Mend tears, loose hems, and seams.

• Treat spots and stains.

• Stained or wet garments should bewashed promptly for best results.

SORTING• Separate heavily soiled items from

lightly soiled ones, even if theywould normally be washed together.Separate lint givers (towels, chenille)from lint takers (corduroy, synthetics,permanent press), When possible,turn lint givers inside out.

• Separate dark colors from light colors,colorfast items from non-colorfast items.

• Sort by fabric and construction(sturdy cottons, knits, delicate items).

20

LOADING

Proper loading of your washercontributes to proper cleaning andfabric care and reduces machine noise,

• Drop items into washer loosely. Fillto the top of the basket (top row ofholes). Do not wrap items around theagitator. Items should move easilythrough wash water for best cleaningand wrinkle-free results. Items shouldsink and reappear later.

• Load washer properly and select correctwater level setting. Overloading orpacking the machine, and selecting asetting too small for the wash load can:

cause poor cleaning

increase wrinklingcreate excessive lint

wear out items faster(because of pilling)

• Load by the amount of space itemstake up, not by their weight.

• Mix large and small items in each load.Load evenly to maintain washer balance.An off-balance load can make thewasher vibrate during spin.

• Use a higher water level setting toreduce wrinkling with permanent pressclothes and some synthetic knits. Theseitems should have more room to move inthe water than heavy items (towels,jeans).

• Reduce wash time by using a lowerwater level setting. Loads with only a fewsmall items need less wash time.

LOADING SUGGESTIONS

For these suggested full-sized loads,set the WATER LEVEL selector to thehighest water level setting.

SUPER CAPACITY WASHERS

Heavy WorkClothes

4 jeans

4 workpants

4 workshirts

2 sweatshJrt

2 sweatpants

Towels

10 bath towels

10 hand towels

14 wash cloths

Mixed Load

3 sheets

(1 king, 2twin)

4 pillowcases

3 shirts

3 blouses

9 T-shirts

9 shorts

10 handkerchiefs

21

CLEANING YOUR WASHER

Exterior

Wipe up detergent, bleach, and other spillswith a soft, damp cloth or sponge as theyoccur. Occasionally wipe the outside of thewasher to keep it looking like new.

Do not put sharp or metal objects in yourwasher. They can damage the finish.Check all pockets for pins, clips, money,bolts, nuts, etc. Do not lay these objects onyour washer after emptying pockets.

Interior

Clean interior with 1 cup (250 mL)of chlorine bleach mixed with 2 cups(500 mL) of detergent. Run washerthrough a complete cycle using hot water.Repeat process if necessary.

NOTE: Remove hard water deposits usingonly cleaners labeled as washer safe.

WATER INLET HOSES

Replace inlet hoses after five yearsof use to reduce the risk of hosefailure. Periodically inspect andreplace inlet hoses if bulges, kinks,cuts, wear, or leaks are found. Whenreplacing your inlet hoses, mark thedate of replacement on the label witha permanent marker.

WINTER STORAGEOR MOVING CAREInstall and store your washer whereit will not freeze, Because some watermay stay in the hoses, freezing candamage your washen If storing ormoving your washer during freezingweather, winterize it,

To winterize washer:

1. Shut off both water faucets.

2, Disconnect and drain water inlet hoses.

3. Put 1 qt (1 L) of R.V.-type antifreezein the basket.

4. Run washer on a SPIN setting forabout 30 seconds to mix the antifreezeand water. Some of the mixture willpump out while the washer spins.

5. Unplug washer or disconnect power.

To use washer again:

1. Flush water pipes and hoses.2, Reconnect water inlet hoses.

3. Turn on both water faucets.

4. Plug in washer or reconnect power.

5. Run the washer through a completecycle with 1 cup (250 mL) of detergentto clean out antifreeze.

NON-USE OR VACATION CARE

Operate your washer only when you areat home. If you will be on vacation ornot using your washer for an extendedperiod of time, you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer.This helps avoid accidental flooding(due to a water pressure surge) whileyou are away.

22

Most laundering problems are easily solved if you understand the cause. Checkthese lists for common laundry and washer problems. If you need further assis-tance, see service and assistance information on back cover.

Problem Possible Cause Solution

Washer Leaks Household plumbing is leaking. Repair plumbing.

Inlet hoses not tight. Tighten hoses (see "InstallationInstructions" ).

Inlet hose washers not Reseat washers (see "Installationproperly seated. Instructions" ).

Drain hose not properly Clamp drain hose (see "installationclamped or is off. Instructions").

Drain is clogged. Remove drain clogs. Sink, standpipe,or floor drain must be able to handle17 gal. (64 L) of water per minute.

Tub moved forward during Ensure tub is centered beforeunloading, causing water starting washer.to deflect off tub ring.

Unit not level causing water Ensure front feet are installed andto deflect off tub ring. nuts are tightened. Level washer.

Reset rear Iegs (see "InstallationInstructions").

Load is unbalanced. Spray Redistribute the load.dnses are deflecting off load.

Washer is overloaded. Fills Reduce load size.or spray rinses are deflectingoff load.

Won't Drain/ Drain hose is kinked or Straighten or unplug hose (seeWon't Spin/ clogged. "Installation Instructions").Wet Loads

Correct operation of After a wash or rinse, the washer willneutral drain, drain without spinning. After draining,

the spinning begins.

Lid is open. Close the lid.

Drain hose is more than Lower drain hose (see "Installation96 in. (2.4 m) above the floor. Requirements').

Toe much detergent- Use less detergent.excessive sudsing.

Low voltage or using an Check electrical source or callextension cord. electrician. Do not use extension

cords.

Cold rinses. Cold rinses leave loads wetter thanwarm rinses. This is normal.

23

Problem Possible Cause Solution

Continues Drain hose is less than Raise the drain hose (seeto Fill/ 39 in. (99 cm) above floor. "Installation Requirements").Continuesto Drain/ Drain hose fits tightly into Adjust drain hose for loose fit (see

Cycle Stuck standpipe. "Installation Instructions").

Drain hose taped into Do not seal off drain hose with tape.standpipe. The drain hose needs an air gap.

Washer Makes Load is unbalanced. Redistribute load.Noise

Washer is not level Level washer. Reset rear legs (seeRear Ieveling legs not set. "Installation instructions").

Nuts on front feet not tight. Tighten nuts (see "InstalIationInstructions").

YelIow shipping strap with Remove strap with cotter pinscotter pins not completely (see "Installation Instructions").removed.

Floor not strong enough Relocate washer (see "installationto support washer. Requirements").

Gears engaging after drain This is normal.and before spin.

Upper part of agitator dicks This is normal.during wash.

Won't Water inlet valve Clean screens.

Fill/Won't screens are plugged.Rinse/Won'tAgitate/ Water is turned off. Turn on water.

Wrong Hot and cold hoses are Reverse hoses (see "lnstalIationTemperature reversed. Instructions").

Inlet hose is kinked. Straighten hoses.

Timer dial is not lined up. Turn timer knob to the right slightlyand pull to start.

Power cord not plugged in. Plug into a grounded 3 prong outlet.

24

Problem Possible Cause Solution

Machine Power cord not plugged in. Plug into a grounded 3 prong outlet.Stops

No power at plug. Check electrical source or callelectrician.

Fuse blown or circuit Replace fuse or reset circuit breaker.breaker open. If problem continues, call electrician.

Using an extension cord. Do not use extension cords.

Timer is not lined up. Turn timer to the right slightlyand pull to start.

Timer knob not pulled out. Set and pull out knob.

Machine is overloaded. Wash smaller loads.

Agitator Not The top of the agitator moves This is normal.Working only in one direction.

The top of the agitator is loose. This is normal.

Water Level The top of the agitator is much This is normal.Too Low/Not higher than the highest waterCompletely level. This creates a perceptionFilling of the washer not being full.

Tub is Tub pulled forward when Ensure tub is centered beforeCrooked unloading, starting washer.

Tub moves. This is normal.

Unit not level. Ensure front feet are installed andnuts are tightened. LeveI washer.Reset rear legs (see "InstallationInstructions").

Lint on Load Improper sorting. Sort lint givers from lint takersand by color.

Overloading. Lint can be trapped in load ifoverloaded. Wash smaller loads.

Paper or tissue in pockets. Clean out pockets before washing.

Not enough detergent. Use enough detergent tohold lint in water.

Detergent not dissolving. Use wash water warmer thanWater temperature lower than 70°F (21°C).70°F (21°C).

25

Problem Possible Cause Solution

Tearing Overloading. Improper Loads should move freely duringuse of washer, wash. Wash smaller loads.

Improper use of chlorine Do not pour chlorine bleach directlybleach. Undiluted bleach on load. Wipe up bleach spills.will damage fabrics.

Sharp items not removed Clean out pockets before washing.from pockets; fasteners Zip zippers before washing.not fastened.

Items damaged before Mend rips and broken threads inwashing, seams before washing.

Stains on Improper use of fabric Dilute fabric softener and add toLoad softener in washer or dryer, deep rinse only.

Iron in water (rust). InstalI an iron filter.

Under use of detergent causing Use enough detergent to removesoil to be redeposited, soil and hold it in suspension.

Dye transfer due to not Sort dark clothing from whitessorting loads propedy, and lights.

Dye transfer due to not Unload the washer as soon asunloading washer promptly, it stops.

Load is Not removing load promptly. Unload the washer as soon as it stops.Wrinkled

Overloading. Loads should move freely duringwash. Wash smaller loads.

Hoses reversed. Reverse hoses (see "InstallationInstructions").

Load is Overloading. Loads should move freely duringTangled/ wash. Wash smaller loads.Twisted

Clothes wrapped around Do not wrap items around agitatoragitator, when loading the washer.

26

Your purchase has added value because you can depend on Sears Home CentraP,for service, With over 12,000 trained repair specialists and access to over 4.2million parts and accessories, we have the tools, parts, knowledge and skills toensure our pledge: We Service What We Sell.

Sears Maintenance AgreementsYour Galaxy appliance is designed, manufactured and tested to provide years ofdependable operation. Yet any major appliance may require service from time totime. The Sears Maintenance Agreement offers you an outstanding service program,affordably priced.

The Sears Maintenance Agreement• Is your way to buy tomorrow's service at today's price.

• Eliminates repair bills resulting from normal wear and tear.• Provides for non-technical and instructional assistance,

• Even if you don't need repairs, provides an annual Preventive Maintenance Check,at your request, to ensure that your appliance is in proper runningcondition.

Some limitations apply, For more information, call 1-800-827-6655,

For information concerning Sears Canada Maintenance Agreements,call 1-800-361-6665.

27

28

For repairof cany-in productslikevacuums, lawn equipment,