pcp - ornament tutorial
TRANSCRIPT
-
8/8/2019 PCP - Ornament Tutorial
1/11
Coaster Ornament Tutorial
By Erika Martin (Stampin Mama)
www.stampinmama.com
-
8/8/2019 PCP - Ornament Tutorial
2/11
Supplies:
* Large alphabet stamp set (I used the retired Headline set from SU, but another set can
be substituted for this)
* Cardstock: Kiwi Kiss
* Patterened paper
* Versamark ink* Irridescent Ice embossing powder
* 4 inch round coaster
* Crop-a-Dile or inch hole punch
* Pop-dots
* Old Olive grosgrain ribbon
* Fine grade sandpaper (or a sanding block)
* Embossing gun
Pg. 2
-
8/8/2019 PCP - Ornament Tutorial
3/11
Step 1:
Apply adhesive around the edges
of the 4 inch round coaster. Make
sure to get al the way to the edge.
Place a little bit in the center ofthe coaster, as well.
Step 2:
Place the coaster adhesive side down
on the back side of the piece of
patterned paper that youd like to use
for the base of your ornament.
Step 3:
Trim around the coaster.
Pg. 3
-
8/8/2019 PCP - Ornament Tutorial
4/11
A view of the front of the coaster after
being trimmed.
Step 4:
Use a piece of fine grade sandpaper (or a
sanding block) to sand around the edges of
the coaster and paper.
Step 5:
Cut a piece of Kiwi
Kiss cardstock at 2 x
4 inches.
Pg. 4
-
8/8/2019 PCP - Ornament Tutorial
5/11
Step 6:
Mount the piece of Kiwi Kiss
cardstock on the center of the coaster.
Step 7:
Trim the Kiwi Kiss cardstock to meetflush with the coaster. Sand the edges to
smooth it out.
Step 8:
Cut a piece of
patterned paper at
1 x 4 inches.
Pg. 5
-
8/8/2019 PCP - Ornament Tutorial
6/11
Step 9:
Mount the patterned paper in
the center of the Kiwi Kiss
cardstock.
Step 10:
Trim and sand the edges of the
patterned paper.
Step 11:
Cut a strip
of
patterned
paper at
x 4
inches.
Pg. 6
-
8/8/2019 PCP - Ornament Tutorial
7/11
Step 12:
Mount the strip of patterned paper
across the center of the coaster.
Trim and sand the edges of the
patterned paper.
Step 13:
Stamp the letters J, O and Y on a scrap piece of
Kiwi Kiss cardstock with Versamark ink.
Step 14:
Sprinkle the images with Irridescent Ice
embossing powder.
Pg. 7
-
8/8/2019 PCP - Ornament Tutorial
8/11
Step 15:
Emboss the
images with your
heat gun.
Step 16:
Cut out the letters leaving a
small border of cardstock
around them.
Step 17:
Punch a hole in the top of the coaster
using the Crop-a-Dile or la inch
hole punch.
Pg. 8
-
8/8/2019 PCP - Ornament Tutorial
9/11
Step 18:
Cut a piece of Old Olive grosgrain ribbon at
9 inches long.
Step 19:
Fold the ribbon in half, thread it through the
hole and create a slip knot.
Step 20:
Tie the end of the ribbons off with a double knot and trim
the ends.
Pg. 9
-
8/8/2019 PCP - Ornament Tutorial
10/11
Step 21:
Apply pop-dots to the backs
of the letters.
Step 22:
Mount the letters in the center of the
coaster.
Scroll down for one more
photo.
Pg. 10
-
8/8/2019 PCP - Ornament Tutorial
11/11
Alternate option:
* Mount a matching piece of
patterned paper on the back of
the coaster if youd like. Or,mount a piece of coordinating
cardstock on the back.