3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute

3 Motor Mount Pieces. Make sure the frontpiece is glued first to the front of the fuselage.It must follow the angle of the nose to give the motor the propper down angle. Then glue eithera small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give the motor screws something to screw into.

1/4” wooden dowel or BBQ Skewers glued on the fuselage with hot glue or epoxy. Their location is approximate but needed to stiffen up the fuselage

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

Servo

Servo

Aileron servo strap

Popcicle stickpushrod support

3D Side View Top View

BBQ Skewers glued at about a 45 degree angle between the fuselage and the wing with hot glue or epoxy. Their location is approximate but needed to support the fuselage from folding over on the wing. They also help support the wing.

3 Motor mountpieces.

Aileron servo straps

Popcicle stickpushrod support

*** Make sure “Page Scaling” is turned OFF ***

Center of gravity window is,2.75 - 3.0 inches back from the leading edge.

www.MikeysRC.com

www.MikeysRC.com

Aileron servo straps

Plane Requirements*11.1V 1300-1800 mAh Li-po.*Brushless motor with flat mount. 47 gram 2200kv motor for super fast flying. Or 1400kv motor for fast speeds or 1000kv motor for more moderate speeds.*25 - 30 amp speed control.*6 X 4 prop. om the 2200kv motor OR 10 X 6 prop on the other motor combos.*3, 9 gram servos.

Build Materials*1/4 inch Foam core for the fuselage, wings and tail.*About 8 Popsicle sticks. *1/16 Drill Rod (from a hardware store) or RC pushrods, about 20 inches are needed.*Hot glue or 5 min epoxy.*1/4 inch wooden dowel (20 inches) OR 4 BBQ skewers to add stiffness to the fuselage.* 4 wooden BBQ skewers to support the fuselage / wing.

Glue 1/4 inch dowel here

3 motor mount pieces.

Set aileron deflection for CRAZY fast rolls to 5/8 of an inch for up and down.

MAX elevator deflection 3/4 inch up and down.

Cut 2 BBQ skewers this long.

Cut 2 BBQ skewers this long.

Some aviation humor just for fun.You May Be A Redneck Pilot If...... you think sectionals charts should show trailer parks.... you have mud flaps on your wheel pants.... your toothpick keeps poking your mike.... you have a black airplane with a big #3 on the side.... you refer to flying in formation as "We got ourselves a convoy!"... your go/no-go checklist includes the words "Skoal" or "Redman."

**PRINT THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long. If it measures to 5 inches thenprint the rest of the pages.

*You will need to trim any side of a pagethat has the red guide lines. These linesshould match up exactly and will be 3inches long.

PDF NOTES and TIPS

5 inches

Print scale

COPYRIGHT 2009 MikeysRCDo NOT Redistribute