MATERIAL DATA SHEET SISTEMWILDAN 450 Acrylic Finish

PRODUCT DESCRIPTION A fast drying, acrylic solvent based gloss finish

RECOMMENDED USEFinishing coat tor protection of steel and concrete over suitable primer on interior and exterior areas.

CHARACTERISTICS Good gloss and colour retention. Rapid drying-time Good exterior durability. Good flexibility and abrasion resistance

PHYSICAL DATAColourGloss LevelVolume SolidDry Film ThicknessNumber of CoatTheoretical CoverageTemperature ResistanceVOC Flash PointShelf Life Pack Size

Available On Request Satin Approx. 55%50 microns per coat111.Sq. m/ for 50 microns Maximum : 1000C (dry)441 g/360CAt least 12 months5 litres; 20 litres

SURFACE PREPARATIONPrevious suitable primer coat, dry and free from any contamination.

APPLICATION DATA Application Methods Airless Spray Nozzle Tip Nozzle Pressure Conventional Spray Nozzle Tip Nozzle Pressure Brush or RollerMixing Ratio ThinnerCleanerSurface Temperature

0.38 0.46 mm (0.015 0.018 inch)10 MPa (approx. 43 psi)

1.8 - 2.0 mm (0.071 - 0.079 inch) 0.3 MPa (approx. 43 psi) RecommendedOne component . Thinner WILDAN 620Thinner WILDAN 120Should be 10C - 490C, at least 30C above the dew point to prevent condensation

Drying TimeTouch Dry Hard Dry To Topcoat Minimum Maximum

10 minutes at 250C, 5 minutes at 32C 2 hours at 250C, 1 hour at 320C

2 hours at 250C, 1 hours at 320C Unlimited (roughened and dry)

SAFETY PRECAUTION

Keep away from heat, spark and open flames. Avoid breathing of vapour on skin and eye contact. Keep container closed and store in cool, ventilated area when not in use.

Proper ventilation and protective measures must be provided during mixing, application and drying, to keep vapour concentration within safe limits and to protect against toxic hazard.Necessary safety equipment must be used and ventilation requirements carefully observed, especially in confined or enclosed spaces, such as tank interior and building

DISCLAIMERThe information in this product data sheet is given to the best of our knowledge based on laboratory testing and practical experience. If the product is used under condition beyond our control, we cannot guarantee anything but the quality of the products it self. The information in this product data sheet is liable for modification from time to time in the light of experience and our policy of continuous product development, and without further notice.

PT. KORIPIS KENCANA PERKASADistributor WILDAN Paint

MATERIAL DATA SHEET SISTEMWILDAN 501 A/C Zinc Chromate Alkyd Primer

PRODUCT DESCRIPTION Anti corrosive zinc chromate alkyd primer.

RECOMMENDED USEEconomic general purposes maintenance and new building primer suitable for use on superstructures and on steel surfaces not normally exposed to water immersion.

CHARACTERISTICS Fast dry alkyd primer. To be recoated with conventional paint systems. An economic primer for structural steel. Pigmented with zinc chromate pigments.

PHYSICAL DATAColourGloss LevelVolume SolidDry Film ThicknessNumber of CoatTheoretical CoverageTemperature Resistance

VOC Flash PointShelf Life Pack SizeAvailable On RequestFlatApprox. 55%50 microns per coat111.00 sq.m/ for 50 micronsContinuous : 900CIntermittent : 1150C233 g/380CAt least 12 months25 Kilogram

SURFACE PREPARATIONDry abrasive blast to a minimum ISO - Sa 2 or SSPC - SP 6 Commercial. Blast to achieve a 25 microns anchor profile as indicated with a Keane Tutor Surface Profile Comparator. Remove abrasive residue or dust from surface.

APPLICATION DATA

SAFETY PRECAUTIONApplication Methods Airless Spray Nozzle Tip Nozzle Pressure Conventional Spray Nozzle Tip Nozzle Pressure Brush or RollerMixing Ratio ThinnerCleanerSurface Temperature

Approx. 0.28 mm (0.011 inch) 10 MPa (approx. 1400 psi)

1.8 - 2.0 mm (0.071 - 0.079 inch) 0.3 MPa (approx. 43 psi) RecommendedOne component . Thinner WILDAN 909 - 610Thinner WILDAN 909 - 120Should be 10C - 490C, at least 30C above the dew point to prevent condensation.

Drying Time Touch Dry Hard Dry To Topcoat Minimum Maximum.

1 hours at 250C8hours at 250C

12 hours at 250C, 7 hours at 320C Unlimited (roughened and dry)

Keep away from heat, spark and open flames. Avoid breathing of vapour on skin and eye contact. Keep container closed and store in cool, ventilated area when not in use.Proper ventilation and protective measures must be provided during mixing, application and drying, to keep vapour concentration within safe limits and to protect against toxic hazard.Necessary safety equipment must be used and ventilation requirements carefully observed, especially in confined or enclosed spaces, such as tank interior and building.

DISCLAIMERThe information in this product data sheet is given to the best of our knowledge based on laboratory testing and practical experience. If the product is used under condition beyond our control, we cannot guarantee anything but the quality of the products it self. The information in this product data sheet is liable for modification from time to time in the light of experience and our policy of continuous product development, and without further notice.

PT. KORIPIS KENCANA PERKASADistributor WILDAN PaintMATERIAL DATA SHEET SISTEMWILDAN 501 Synthetic Gloss Enamel

PRODUCT DESCRIPTION A single component alkyd gloss enamel finish.

RECOMMENDED USEA gloss finish coat for mild industrial and marine service. For steel work in non aggrasive environment.

CHARACTERISTICS Easily applied by spray, brush or roller. Good gloss retention, even in industrial environment. Suitable for areas of limited chemical exposure. Excellent maintenance coating, compatible with a wide range of primer and existing coated surface.

PHYSICAL DATAColourGloss LevelVolume SolidDry Film ThicknessNumber of CoatTheoretical CoverageTemperature Resistance

VOC Flash PointShelf Life Pack SizeAvailable on requestGlossApprox.53%40 microns per coat1-213.20 sq. m/ for 40 micronsContinuous : 900C (dry)intermittent : 1150C (dry)237 g/380CAt least 12 months5 liters, 20 litres

SURFACE PREPARATIONSteelDry abrasive blast to minimum ISO - Sa 2 or SSPC - SP 6 Commercial. Blast to achieve a 25 microns anchor profile as indicated with a Keane Tutor Surface Profile Comparator. Remove abrasive residue or dust from surface. For aged coating, all intact coatings must be clean, dry and free of all contaminants, sufficiently roughened.

APPLICATION DATAApplication MethodsAirless SprayNozzle TipNozzle PressureConventional SprayNozzle TipNozzle PressureBrush or RollerThinnerCleanerSurface Temperature

Drying Time

Approx. 0.28 mm (0.011 inch) 10 MPa (approx. 1400 psi)

1.8 - 2.0 mm (0.071 - 0.079 inch) 0.3 MPa (approx. 43 psi) RecommendedThinner WILDAN 909 - 610Thinner WILDAN 909 - 120Should be 100C - 490C, at least 30C above the dew point to prevent condensation.

Touch Dry Hard Dry Over Coating Minimum Maximum2 hours at 250C, 1 hour at 320C 8 hours at 250C, 4 hour at 320C

16 hours Unlimited

SAFETY PRECAUTIONKeep away from heat, spark and open flames. Avoid breathing of vapour on skin and eye contact. Keep container closed and store in cool, ventilated area when not in use.Proper ventilation and protective measures must be provided during mixing, application and drying, to keep vapour concentration within safe limits and to protect against toxic hazard.Necessary safety equipment must be used and ventilation requirements carefully observed, especially in confined or enclosed spaces, such as tank interior and building.

DISCLAIMERThe information in this product data sheet is given to the best of our knowledge based on laboratory testing and practical experience. If the product is used under condition beyond our control, we cannot guarantee anything but the quality of the products it self. The information in this product data sheet is liable for modification from time to time in the light of experience and our policy of continuous product development, and without further notice.

PT. KORIPIS KENCANA PERKASADistributor WILDAN Paint

MATERIAL DATA SHEET SISTEM

WILDAN 801QD Alkyd Gloss Enamel

PRODUCT DESCRIPTION A single component styrene modified alkyd resin

RECOMMENDED USEA gloss finish coat for mild industrial and marine service. For steel work in non aggrasive environment.

CHARACTERISTICS Easily applied by spray. Good gloss retention, even in industrial environment. Suitable for areas of limited chemical exposure. Excellent maintenance coating, compatible with a wide range of primer and existing coated surface.

PHYSICAL DATAColourGloss LevelVolume SolidDry Film ThicknessNumber of CoatTheoretical CoverageTemperature Resistance

VOC Flash PointShelf Life Pack SizeAvailable on requestGlossApprox.53%40 microns per coat1-213.20 sq. m/ for 40 micronsContinuous : 900C (dry)intermittent : 1150C (dry)237 g/380CAt least 12 months5 liters, 20 litres

SURFACE PREPARATIONSteelDry abrasive blast to minimum ISO - Sa 2 or SSPC - SP 6 Commercial. Blast to achieve a 25 microns anchor profile as indicated with a Keane Tutor Surface Profile Comparator. Remove abrasive residue or dust from surface. For aged coating, all intact coatings must be clean, dry and free of all contaminants, sufficiently roughened.

APPLICATION DATAApplication Methods Airless Spray Nozzle Tip Nozzle Pressure Conventional Spray Nozzle Tip Nozzle PressureThinnerCleanerSurface Temperature

Drying Time

Approx. 0.28 mm (0.011 inch) 10 MPa (approx. 1400 psi)

1.8 - 2.0 mm (0.071 - 0.079 inch) 0.3 MPa (approx. 43 psi) Thinner WILDAN 909 - 610Thinner WILDAN 909 - 120Should be 100C - 490C, at least 30C above the dew point to prevent condensation.

Touch Dry Hard Dry Over Coating Minimum Maximum10 Minutes at 250C, 1 hour at 320C 5 hours at 250C, 4 hour at 320C

16 hours Unlimited

SAFETY PRECAUTIONKeep away from heat, spark and open flames. Avoid breathing of vapour on skin and eye contact. Keep container closed and store in cool, ventilated area when not in use.Proper ventilation and protective measures must be provided during mixing, application and drying, to keep vapour concentration within safe limits and to protect against toxic hazard.Necessary safety equipment must be used and ventilation requirements carefully observed, especially in confined or enclosed spaces, such as tank interior and building.

DISCLAIMERThe information in this product data sheet is given to the best of our knowledge based on laboratory testing and practical experience. If the product is used under condition beyond our control, we cannot guarantee anything but the quality of the products it self. The information in this product data sheet is liable for modification from time to time in the light of experience and our policy of continuous product development, and without further notice.

PT. KORIPIS KENCANA PERKASADistributor WILDAN PaintMATERIAL DATA SHEET SISTEMWILDAN 801 QD Alkyd Doff Enamel

PRODUCT DESCRIPTION A single component styrene modified alkyd resin

RECOMMENDED USEA doff finish coat for mild industrial and marine service. For steel work in non aggrasive environment.

CHARACTERISTICS Easily applied by spray. Good doff retention, even in industrial environment. Suitable for areas of limited chemical exposure. Excellent maintenance coating, compatible with a wide range of primer and existing coated surface.

PHYSICAL DATAColourGloss LevelVolume SolidDry Film ThicknessNumber of CoatTheoretical CoverageTemperature Resistance

VOC Flash PointShelf Life Pack SizeAvailable on requestDoffApprox.53%40 microns per coat1-213.20 sq. m/ for 40 micronsContinuous : 900C (dry)intermittent : 1150C (dry)237 g/380CAt least 12 months5 liters, 20 litres

SURFACE PREPARATIONSteelDry abrasive blast to minimum ISO - Sa 2 or SSPC - SP 6 Commercial. Blast to achieve a 25 microns anchor profile as indicated with a Keane Tutor Surface Profile Comparator. Remove abrasive residue or dust from surface. For aged coating, all intact coatings must be clean, dry and free of all contaminants, sufficiently roughened.

APPLICATION DATAApplication Methods Airless Spray Nozzle Tip Nozzle Pressure Conventional Spray Nozzle Tip Nozzle PressureThinnerCleanerSurface Temperature

Drying Time

Approx. 0.28 mm (0.011 inch) 10 MPa (approx. 1400 psi)

1.8 - 2.0 mm (0.071 - 0.079 inch) 0.3 MPa (approx. 43 psi) Thinner WILDAN 909 - 610Thinner WILDAN 909 - 120Should be 100C - 490C, at least 30C above the dew point to prevent condensation.

Touch Dry Hard Dry Over Coating Minimum Maximum10 Minutes at 250C, 1 hour at 320C 5 hours at 250C, 4 hour at 320C

16 hours Unlimited

SAFETY PRECAUTIONKeep away from heat, spark and open flames. Avoid breathing of vapour on skin and eye contact. Keep container closed and store in cool, ventilated area when not in use.Proper ventilation and protective measures must be provided during mixing, application and drying, to keep vapour concentration within safe limits and to protect against toxic hazard.Necessary safety equipment must be used and ventilation requirements carefully observed, especially in confined or enclosed spaces, such as tank interior and building.

DISCLAIMERThe information in this product data sheet is given to the best of our knowledge based on laboratory testing and practical experience. If the product is used under condition beyond our control, we cannot guarantee anything but the quality of the products it self. The information in this product data sheet is liable for modification from time to time in the light of experience and our policy of continuous product development, and without further notice.

PT. KORIPIS KENCANA PERKASADistributor WILDAN Paint