plastic materials selection - milwaukee...
TRANSCRIPT
![Page 1: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/1.jpg)
Plastic Materials Selection
Jose M. Perez, Jr.Senior Engineer, Polymers
Element - New Berlin
![Page 2: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/2.jpg)
Introduction
Engineers face several considerations when selectingEngineers face several considerations when selecting the optimum polymer material for a product• Knowing full product requirements in a wide range of environments
• Thoroughly understanding of the true functional behavior of the polymerof the polymer
• Using this knowledge to sift through an almost infinite number of resin/additive combinations
Plastic Materials Selection
![Page 3: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/3.jpg)
Introduction
Polymer basicsPolymer basics• Material behavior differences
Selection considerations Selection considerations
Material datasheets
Q/A
Plastic Materials Selection
![Page 4: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/4.jpg)
What is a “Polymer”?
“Polymer” is from the Greek “poly” (many)Polymer is from the Greek poly (many) and “meros” (part)
“Polymers” are long organic molecules made up of many small units (monomers) chemically joined end‐to‐end
Plastic Materials Selection
![Page 5: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/5.jpg)
Common Mer Structures
PolyethylenePolybutadiene
o yet y e e
PolypropyleneNylon 6
yp py
Polyvinyl chloride
Polycarbonate
Polystyrene
Polyethylene terephthalate
Polystyrene
Polytetrafluoroethyleney y
![Page 6: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/6.jpg)
Polymer Characterization
Thermoplastic ThermosetThermoplastic• Soften when heated, harden
upon cooling
Thermoset• Hardened when heated
• Due to chemical cross links • Can be re‐softened
• Limited upper service temperature
cannot be re‐softened
• Generally higher temperaturetemperature
• Readily recyclable• Difficult to recycle
Plastic Materials Selection
![Page 7: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/7.jpg)
Examples
Thermoplastic Thermosetp• Polypropylene (PP)
• Polyamide (PA, a.k.a Nylon)
• Phenolic (PF)
• Epoxy (EP)
• Polycarbonate (PC)
• Acrylonitrile butadiene styrene (ABS)
• Unsaturated polyester (UP)
• Polyurethane (PUR)(ABS)
• Polyacetal (POM)
• Poly(ethylene terephthalate)
• Acrylonitrile butadiene rubber (NBR)
• Ethylene propylene diene• Poly(ethylene terephthalate) (PET)
• Ethylene propylene‐dienemonomer (EPDM) rubber
Plastic Materials Selection
![Page 8: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/8.jpg)
Thermoplastic Types
Amorphous – lacking long range orderAmorphous lacking long range order
Semi‐crystalline ‐ polymers possessing long range molecular order
Plastic Materials Selection
![Page 9: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/9.jpg)
General Traits
Amorphous Semi‐crystalline(Many exceptions exist)
Amorphous• Poor chemical resistance
• Lower use temperature
Semi crystalline• Chemically resistant
• Higher use temperature
• Optically transparent
• Less mold shrinkage
• Tighter tolerances possible
• Optically opaque
• More mold shrinkage
• Requires looser toleranceg p
• Lower strength
• Higher toughness
• Lower density
q
• Higher strength
• Lower toughness
• Higher density• Lower density • Higher density
Plastic Materials Selection
![Page 10: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/10.jpg)
General Traits
Amorphous materials can be characterized by theirAmorphous materials can be characterized by their glass transition temperature (Tg)
Glass transition temperature ‐ The temperature at which a material's characteristics change from that g fof a glass to that of rubber.
Semi‐crystalline materials can be characterized by their Tg and melting temperature (Tm)
Plastic Materials Selection
![Page 11: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/11.jpg)
Thermal Properties
Material Tg [°C (°F)] Tm [°C (°F)]
Polyethylene (low density) ‐110 (‐165) 115 (240)
Polytetrafluoroethylene ‐97 (‐140) 327 (620) Polyethylene (high
90 ( 130) 137 (279)density)
‐90 (‐130) 137 (279)
Polypropylene ‐18 (0) 175 (347)
Nylon 6,6 57 (135) 265 (510)
Polyester (PET) 69 (155) 265 (510)
Polyvinyl chloride 87 (190) 212 (415)
Polystyrene 100 (212) 240 (465)
Polycarbonate 150 (300) 265 (510)
Polysulfone 185 (365) 360 (680)
![Page 12: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/12.jpg)
Effect of Morphology
As crystallinity increases so does: As amorphous content y y• Hardness
• Density
pincreases so does:• Impact strength
• Dimensional stability• Modulus
• Tensile strength
• Melting point
• Dimensional stability
• Clarity
• Stress crack resistanceMelting point
• Permeability resistance
• Resistance to oils and greases
• Elongation
• Surface gloss
Plastic Materials Selection
![Page 13: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/13.jpg)
Examples
Amorphous• Polyetherimide (PEI)
Semi‐Crystalline• Polyetheretherketone (PEEK)• Polyetherimide (PEI)
• Polyethersulfone (PES)
• Polysulfone (PSU)
• Polyetheretherketone (PEEK)
• Polyphenylene Sulfide (PPS)
• Polythalamide (PPA)
• Polycarbonate (PC)
• Polyvinyl Chloride (PVC)
• Acrylonitrile butadiene styrene (ABS)
• Polyamide (PA)
• Polyethylene Terephthalate (PET)
• Polybutylene Terephthalate (PBT)
• Styrene Acrylonitrile (SAN)
• Polystyrene (PS)
• High Impact polystyrene (HIPS)
• Polyoxymethylene (Acetal or POM)
• Polypropylene (PP)
• Polyethylene (HDPE/LDPE/LLDPE)• High Impact polystyrene (HIPS)
• Polymethylmethacrylate (PMMA or Acrylic)
• Polyethylene (HDPE/LDPE/LLDPE)
Costs range from <$1.50/lb for Commodity to >$4/lb for Hi-Temp/Hi-Performance
Plastic Materials Selection
g y pData courtesy of RTP Company
![Page 14: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/14.jpg)
Chemical Structure Influence
Acrylonitrile butadiene styrene (ABS) ‐ Amorphous
Pros ConsGood stiffness Low maximum continuous
use temperatureE ll t T h use temperatureExcellent ToughnessClass A surface Not resistant to solvents,
hydrocarbons and fuelsPlatabilityResistant to alkalis and acids Poor weatherability
• Specific properties dependent on amount of each phase
Typical applications Typical applications• Climate control and radio bezels in automotive• Housings in consumer electronics and appliances
Plastic Materials Selection
![Page 15: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/15.jpg)
Chemical Structure Influence
Polycarbonate (PC) ‐ Amorphousy ( ) p
Pros ConsExcellent toughness Poor chemical resistanceLow warpage Processing difficultiesDimensional stability Low fatigue enduranceTransparency
Typical applications
TransparencyLow mold shrinkage
Typical applications• Lighting lenses, climate control and radio bezels in automotive
• Housings in consumer electronics and appliances
Plastic Materials Selection
![Page 16: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/16.jpg)
Chemical Structure Influence
Acetal (POM) – Semi‐crystalline
Pros ConsGood mechanical strength Not resistant to acidsExcellent fatigue resistance High specific gravityg g p g yAbrasion resistance Anisotropic shrinkageLow coefficient of friction Processing difficultiesLow creep
• Specific properties dependent on homopolymer versus copolymer
Low creepResistant to fuels and solvents
Typical applications• Fuel system components in automotive• Gears in appliance and machinery industries
Plastic Materials Selection
![Page 17: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/17.jpg)
Chemical Structure Influence
Nylon 6,6 (PA66) – Semi‐crystalliney , ( ) y
Pros ConsExcellent toughness High water absorptionHeat resistance Poor resistance to strong
acids and basesAbrasion resistanceResistant to fuels, solvents,
• Specific properties dependent on absorbed water content
T pical applications
, ,and hydrocarbons
Typical applications• Engine and cooling system components in automotive
• Cams and gears in appliance and machinery industries
Plastic Materials Selection
![Page 18: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/18.jpg)
Chemical Structure Influence
Polypropylene (PP) – Semi‐crystallineyp py ( ) y
Pros ConsChemical resistant Low to moderate mechanical
propertiespropertiesLightweightHeat resistant Low surface energyLow cost• Specific properties dependent on homopolymer versus copolymer
Typical applications• Fan shrouds, battery housings, windshield washer reservoirs, climate , y g , ,
control housings and conduits in automotive• Housings in appliances• Consumer product packaging
Plastic Materials Selection
![Page 19: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/19.jpg)
Additives
PlasticizersD th l t iti t t (T ) ft d dd• Decreases the glass transition temperature (Tg), softens and adds flexibility to the product
• Flame retardants• Can increase resistance to ignition, reduce rate of burning, flame
spread, and smoke emission• Halogenated vs. nonhalogenated
PropertyPolypropylene HomopolymerUnfilled V0 V2
Tensile Strength (MPa) 32 23 30Tensile Strength (MPa) 32 23 30Tensile Modulus (MPa) 1,724 1,862 1,517
Impact Strength (J/m) 53 43 37
Plastic Materials Selection
Data courtesy of RTP Company
![Page 20: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/20.jpg)
Additives
StabilizersStabilizers• UV, oxidation, hydrolysis, etc…
Antistatic agentsg
Blowing agents
ColorantsColorants• Organic vs. inorganic
FillersFillers• Reinforcing, non‐reinforcing, & specialty
Plastic Materials Selection
![Page 21: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/21.jpg)
Reinforcing Fillers
Improves mechanical performance of the material byImproves mechanical performance of the material by transferring stress to the reinforcement, which is then diluted before transfer back to the polymer matrix.
Includes fibers and high aspect ratio minerals.g p
Aspect ratio and coupling are key variables in the effectiveness of the reinforcementeffectiveness of the reinforcement.
Plastic Materials Selection
![Page 22: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/22.jpg)
Aspect Ratio
Defined as length divided by diameter.
A higher aspect ratio will result in a higher increase inA higher aspect ratio will result in a higher increase in strength.
Bead Short Fiber Long Fiber Nano Fiber
( 1……………………………Aspect Ratio…………………….………1,000 )
Plastic Materials Selection
![Page 23: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/23.jpg)
Aspect Ratio
Bead or Sphere• Not effective as reinforcement (except for compression)
Sh Fib ( 1 ) Short Fibers (~1 mm)• Most popular due to effectiveness
• Accelerates tool wear
• Increases potential for part warpage and anisotropy
Anisotropy a state in which a physical characteristic variesAnisotropy ‐ a state in which a physical characteristic varies in value along axes in different directions.
Plastic Materials Selection
![Page 24: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/24.jpg)
Aspect Ratio
Long Fibers (10 mm)• Often used in large parts for increasing overall part strength
• Fiber length retention critical to effectiveness• Fiber length retention critical to effectiveness
• Increases potential for part warpage and anisotropy
• Costs may increase as regrind should not be used within same part
Nano Fibers• Excellent reinforcement without part warpage and anisotropyp p g py
• High material costs
Plastic Materials Selection
![Page 25: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/25.jpg)
Aspect Ratio
Tensile Properties Comparison for Polypropylene Resins
Property UnfilledGlass Bead Filled
Glass Fiber Filled
Glass Fiber
R i f d
Long Glass Fiber
R i f dFilled Filled Reinforced ReinforcedFiller (Wt %) 0 30 30 30 30Strength (MPa) 32 23 55 76 100Elongation (%) >10 >10 1.5 - 2.5 4 - 5 2.5 - 3.5
Modulus (GPa) 1.72 2.34 6.21 6.21 6.90Data courtesy of RTP Companyy p y
Plastic Materials Selection
![Page 26: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/26.jpg)
Non‐Reinforcing Fillers
Low aspect ratio minerals and particles used to displace resin p p pand reduce the cost of the overall material. Can also be added for cosmetic reasons, such as to reduce the appearance of sink marksmarks.
Includes kaolin clay talc calcium carbonate titania silica glass Includes kaolin clay, talc, calcium carbonate, titania, silica, glass beads, wollastonite, wood fiber, etc…
Plastic Materials Selection
![Page 27: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/27.jpg)
Non‐Reinforcing Fillers
Tensile Properties Comparison for Polypropylene Resins
Property Unfilled Calcium
Carbonate Filled
Talc Filled
Mica Filled
Glass Fiber Reinforced
Filler (Wt %) 0 40 40 40 40
Strength (MPa)
32 23 30 28 90(MPa)Elongation (%)
>10 >10 >10 9 3 - 4
Modulus 1 72 3 10 5 17 6 21 8 96Modulus (GPa)
1.72 3.10 5.17 6.21 8.96
Data courtesy of RTP Company
Plastic Materials Selection
![Page 28: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/28.jpg)
Specialty Fillers
Electrically conductive, wear/friction inhibitors, thermally conductive, dampening controlconductive, dampening control
l d b f b l l f b k l d Includes carbon fiber, stainless steel fiber, nickel coated graphite, tungsten, molybdenum disulfide, PTFE, silicone oil, barium sulfate, graphite, barium sulfate, etc…oil, barium sulfate, graphite, barium sulfate, etc…
Plastic Materials Selection
![Page 29: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/29.jpg)
Selection Considerations
General Information AppearanceGeneral Information
Assembly Method
Mechanical
Appearance
Codes and SpecificationsMechanical
Requirements
Chemical Resistance
p
Disposal
Cost ParametersChemical Resistance
Electrical Properties
Operating Environment
Cost Parameters
Other Needs
Operating Environment
*Rank from most to least important
Plastic Materials Selection
![Page 30: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/30.jpg)
General Information
Part functionPart function
Part geometry and tolerancing
Design constraints (e g weight)Design constraints (e.g. weight)
Required service life
Servicing requirements Servicing requirements
Consequences of part failure
Production scale Production scale
Plastic Materials Selection
![Page 31: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/31.jpg)
Assembly Method
Mechanical fasteningMechanical fastening• Self tapping screws, press fit, snap fit, heading, insert
Weldingg• Hot plate, induction, vibration, spin, ultrasonic
Adhesive methods• Adhesive bonding, solvent bonding
Plastic Materials Selection
![Page 32: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/32.jpg)
Mechanical Requirements
Applied stress while in serviceApplied stress while in service Magnitude, speed, frequency, duration
Maximum tolerable deformation % of Yield
Effects of friction and wear Add a lubricant?
Dimensional stability Add filler
Plastic Materials Selection
![Page 33: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/33.jpg)
Operating Environment
Sunlight and weathering• Duration • Intensity
H idit Humidity Ozone Temperature Temperature
• Maximum continuous• Short term elevated • Minimum operating
Polyethylene Polypropylene Nylon Polycarbonate Teflon®
#1 DRIVER OF RESIN COST#1 DRIVER OF RESIN COSTPlastic Materials Selection
![Page 34: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/34.jpg)
Operating EnvironmentT tTemperature
Door comprised of glass bead filled nylon resin
Used in an HVAC system in an automotive application Used in an HVAC system in an automotive application
Improper sealing was evident due to permanent deformation of the door following a short time in service
274.4
300
Dry Wet
229.7
200
250
lus
(ksi
)
y
68.7 64.2
100
150
Flex
ural
Mod
ul
0
50
88 107
Test Temperature (C)
Plastic Materials Selection
![Page 35: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/35.jpg)
Chemical Resistance
Chemical exposure while in service and duringChemical exposure while in service and during secondary processes and assembly.
Material Description Organic Alcohols Hydrocarbons FuelsMaterial Description Solvents Alcohols Hydrocarbons Fuels
Polycarbonate (PC) P G P PHigh Density Polyethylene (HDPE) G E G GPolypropylene (PP) P G F FPolypropylene (PP) P G F FNylon 6/6 (PA66) E G G GAcetal (POM) E F G GPolysulfone (PSU) G G P P
Data courtesy of RTP CompanyP = Poor F = Fair G = Good E = Excellent
y ( )Polybutylene Terephthalate (PBT) E G P GPolyetherehterketone (PEEK) E E E G
Plastic Materials Selection
![Page 36: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/36.jpg)
Electrical Properties
Voltage requirements Voltage requirements
• Dielectric strength
Tracking requirements
Insulation requirementsq
Surface and volume resistivity
Conductive/Dissipative Conductive/Dissipative
Plastic Materials Selection
![Page 37: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/37.jpg)
Appearance
ColorColor• Inorganic pigments can change material’s physical properties
• Color concentrates must be compatible with resin
• Transparency is only possible with amorphous resins
Surface finish• Class “A”, machined, matte, textured
S d ti h i ti l ti hi• Secondary operations such as painting, plating, or graphic appliqués
Plastic Materials Selection
![Page 38: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/38.jpg)
Codes and Specifications
Underwriters Laboratories ‐ UL • Flammability• Electrical insulation • Temperature index
National Sanitary Foundation ‐ N.S.F.Food and Drug Administration FD A Food and Drug Administration ‐ F.D.A.
U.S. Department of Agriculture 3A Sanitary Standards 3A Sanitary Standards OEM/Supplier Material Specifications
Plastic Materials Selection
![Page 39: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/39.jpg)
Disposal
RecycleRecycle
Reclaim / Blend
LandfillLandfill • Restricted substances
IncinerateIncinerate
Plastic Materials Selection
![Page 40: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/40.jpg)
Cost
What are the cost and pricing limitations on the p gpart?
Total part cost • Material costs• Cycle time • Labor rate• Labor rate
• Machine rate• Scrap rateScrap rate
• Amortized mold costs• Secondary operations
Plastic Materials Selection
![Page 41: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/41.jpg)
Relative Market Resin Prices (Cost/pound) Effective October 2013Effective October 2013
8.8Polyetherimide
2 0
2.2
6.5
Nylon 6/6
Polycarbonate
Polysulfone
1.5
2.0
2.0
Acetal
Nylon 6
Nylon 6/6
1.2
1.3
Acrylonitrile-Butadiene-Styrene
Acrylic
1.1
1.2
0 5 10
High Density Polyethylene
Polypropylene
0 5 10
Polyetheretherketone off the chart @ $45/lb!Plastic Materials Selection
![Page 42: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/42.jpg)
Other Additional Needs
OdorOdor
Noise, Vibration, Harshness (NVH)
FoggingFogging
Microbial resistance
Etc Etc…
Plastic Materials Selection
![Page 43: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/43.jpg)
Material Datasheets
Correlation between datasheets and relevance to design Correlation between datasheets and relevance to design considerations is not completely understood
• Material property versus significancep p y g
Purpose of datasheets is often sales and marketing related
• Technical content not always intended for use as engineering dataTechnical content not always intended for use as engineering data
In general, datasheets contain short term, single point, room temperature data, for dry as molded samples
Every data point on a datasheet represents a point at which something bad happened to the material
Plastic Materials Selection
![Page 44: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/44.jpg)
Temperature & Humidity Effect
30% Glass Reinforced, Heat Stabilized, Nylon 6,6
Dry as Molded Equilibrated at 50% Relative Humidity
Data courtesy of DuPont Data courtesy of DuPont
Plastic Materials Selection
![Page 45: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/45.jpg)
Additional Property Influences
Molecular weightMolecular weight
Celcon M25MFR 2.5 g/10 min
Celcon M90MFR 9.0 g/10 min.
Celcon M270 MFR 27 g/10 min.
Plastic Materials Selection
![Page 46: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/46.jpg)
Effect of Molecular Weight
Increasing MW
• Tensile Strength
• Elongation
Yi ld St th
+
++• Yield Strength
• Toughness
• Brittleness
+
+
‐• Brittleness
• Hardness
• Abrasion Resistance
+
+
• Softening Temperature
• Chemical Resistance
+
+
Plastic Materials Selection
![Page 47: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/47.jpg)
Orientation Effect
30% Long Glass Reinforced, H t St bili d
40% Long Glass Reinforced, H t St bili d
Tensile Properties
Heat Stabilized, Polypropylene Homopolymer
Heat Stabilized, Polypropylene Homopolymer
Flow Direction
Cross Flow Direction
Change (%)
Flow Direction
Cross Flow Change
(%)Direction Direction (%) Direction Direction (%)
Modulus (GPa) 7.45 6.17 -16 9.71 7.39 -24
Strength (MPa) 106 60 -43 115 57 -50
Strain @ Ultimate (%) 2.35 1.29 -45 2.11 1.03 -51
Data courtesy of Owens Corning
Flow Direction Cross Flow Direction
Plastic Materials Selection
![Page 48: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/48.jpg)
Alternatives
E i i d i d t Engineering design data • Material supplier
May not include orientation or wall thickness effectsMay not include orientation or wall thickness effects
Long term test data difficult to obtain especially at exact application conditions
Computer databases Computer databases• SABIC Innovative Plastics™ http://www.geplastics.com
• CAMPUS http://www.campusplastics.com
• IDES Prospector http://www ides com• IDES Prospector http://www.ides.com
• Internal test laboratory
• External test laboratoryy
Plastic Materials Selection
![Page 49: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/49.jpg)
References
ASM Engineered Materials Handbook, Vol.2, ASM International, USA (1988)
A Design Guide for Information and Technology Equipment, American Plastics Council©
Chemical Resistance, Vol.1, Second Edition, Plastics Design Library, New York (1994)
MacDermott, C.P., Shenoy, A.V., Selecting Thermoplastics for Engineering , , y, , g p f g gApplications, Second Edition, Marcel Dekker, Inc., New York (1997)
Peraro, J.S. , Limitations of Test Methods for Plastics, American Society for Testing and Materials, Pennsylvania (2000)g , y ( )
Plastic Materials Selection
![Page 50: Plastic Materials Selection - Milwaukee SPEmilwaukeespe.org/wp-content/uploads/2016/02/Milwaukee... · 2020-01-09 · Introduction Engineers face several considerations when selecting](https://reader033.vdocuments.net/reader033/viewer/2022041623/5e4074611e3cd45a4422ba45/html5/thumbnails/50.jpg)
Questions?Q
See our failure analysis services at http://www element comhttp://www.element.com
Phone: 262‐901‐0522Phone: 262 901 0522Email: [email protected]