pmp 450 update for pricing contact maplenet wireless maplenet wirelessmaplenet wireless february...

PMP 450 UPDATE

FOR PRICING CONTACT MAPLENET WIRELESS

February 2014

http://www.maplenetwireless.com/

PMP 450

• 4th Generation (4G) of PMP product family from Cambium• Dramatically increases overall system capacity

– Over 125 Mbps per Access Point – Over 1.5 Gbps of tower bandwidth possible – Can support any symmetrical or asymmetrical speed

• OFDM MIMO provides near Line of Sight (nLOS) and LOS access• Software defined radio design allows for rapid expansion of

frequency bands, both licensed and unlicensed• Utilizes GPS synching capability to achieve maximum spectral

efficiency and very low latency supporting VoIP and video• Installation and turn up in

days, not weeks or months

2© 2014 Cambium Networks, Inc. All rights reserved.

PMP 450 ADVANTAGES

Characteristic Cambium PMP Implications

Channel Access Scheduled TDD – Deterministic and Scalable regardless of load

Without scheduled TDD, users will complain about availability as subscribers are added.

Latency and QoSConsistent and Deterministic – critical for voice and video and T1 replacements

Without consistent latency, network users will complain about delays and poor performance.

GPS Synchronization Supported -> Efficient Channel Re-use / Easy Deployment. in Multi-Sector / Multi-Site systems

Unsynchronized systems perform inconsistently and poorly as subscribers are added. Use more channels to serve the same # of users

Throughput and System Capacity (bits/sec/Hz/sq km)

High ability for frequency reuse. Higher aggregate real user throughput and system capacity for given channel width and available spectrum.

Competitive systems require more AP towers to be added to meet demand – but this adds interference.

Select a solution that meets today’s needs and supports growth


GPS SYNCHRONIZATION

• AP and SM communication is synchronized (all APs and SMs have controlled alternating communication) – reducing self interference

– All SMs within a network– All APs within a cluster– All APs on a tower (multiple clusters)– All APs on all towers in the network

• Enables channel re-use and easy to deploy multi-sector, multi tower networks(minimal tower separation)

• Use the same number of channels to serve a higher number of users


PMP 450: KEY SYSTEM FEATURES

Radio Performance Features Advantage

High-Efficiency Canopy MAC Higher payload capacity and efficient spectrum use

2x2 MIMO w/ Migration Path High capacity and link budgets with path to MU-MIMO in the future

Consistent Very Low Latency Reliable support of voice and video applications

Interoperability Seamless operation with existing PMP 430 SMs

GPS Synchronization Network scalability and self-interference avoidance

Dual Band (5.4 and 5.8 GHz), 2.4 GHz, 3 GHz

One high performance SKU to cover both 5GHz bands, Proliferation of additional frequencies

nLOS Connectivity Enhanced coverage over challenging terrain


PMP 450: ACCESS POINT DIMENSIONS

http://www.cambiumnetworks.com/products/pmp/pmp-450




Quick-Mount Hardware Easy installation

Built-In Surge Suppression on AP No additional parts needed

Physical Features Advantage

PMP 450: ACCESS POINT DETAILS

1000BaseT (Gig-E) Interface Allows for maximum data throughput

High Performance Sector Antennas Specified and Optimized for PMP 450

IP67, IP66 Certified AP Housing Fully weather rated


Connectorized RM

PMP 450: REMOTE MODULE OPTIONS

Antenna Options

Reflector DishCLIP (5 GHz only)Integrated Antenna


PMP 450 REMOTE MODULE TIERS

RMs fully upgradeable from 4 to 60+ Mbps Software keys available to easily move between tiers

Burst bucket has increased from 500 Mb to 2.5 Gb! Amount of burst can be fully managed per RM

Value (4 Mbps)

Residential(10Mbps)

Power (20 Mbps)

Enterprise (Uncapped)

0

10

20

30

40

50

60

SustainedBurst


INTRODUCTION OF PMP 450 - 3 GHZ

Category Specification

Frequency 3.3 to 3.6 GHz, 3.55 to 3.8 GHz

Max Throughput 125 Mbps

Modulation Modes 2x2 MIMO: QPSK, 16QAM, 64QAM, 256QAM

Latency 3-5 ms

Max TX Power +20 dBm per chain (+23 dBm comb)

Channel Bandwidth 5, 10, 20 MHz

Power Consumption 10 W typical , 14 W peak

AP Antenna 17 dBi – (90° sector)

AP Dimensions 11” x 8” (Current PMP 450 AP)

SM Antenna Gain +9 dBi

SM Dimensions (Estimate) 8” x 3” (similar in size to Canopy FSK)

Accessories Dish: +11 dBi (total of 20 dBi)

10

Access Point

Remote Module

© 2014 Cambium Networks, Inc. All rights reserved.

CAMBIUM LAB RESULTS

PMP 450 @ 5 GHZTHROUGHPUT AND RANGE PERFORMANCE

12

20 MHz Channel -- Maximum LOS range mi(km)Frequency Band Modulation Mode Integrated (9dBi) CLIP (17dBi) Reflector Dish (23dBi)

5.8 GHz

256QAM – MIMO-B (8X) 0.3 (0.5) 0.9 (1.5) 1.7 (2.7)64QAM – MIMO-B (6X) 1.1 (1.8) 3.1 (5) 5.5 (8.9)16QAM – MIMO-B (4X) 2.7 (4.3) 7.6 (12.3) 13.5 (21.8)

QPSK – MIMO-B (2X) 6 (9.7) 17 (27) 30 (48)QPSK – SISO (1X) 8.4 (13.6) 23.8 (38) 40 (64)

Modulation Mode

Sensitivity (dBm)

T-put (Mbps)

CNR (dB)

QPSK – MIMO-B (2X) -84 30 1016QAM – MIMO-B (4X) -77 60 1764QAM – MIMO-B (6X) -70 90 24

256QAM – MIMO-B (8X) -64 125 32


PMP 450 @ 2.4 GHZTHROUGHPUT AND RANGE PERFORMANCE

13

Modulation Mode

Sensitivity (dBm)

T-put (Mbps)

CNR (dB)


256QAM – MIMO-B (8X) -66 125 32

20 MHz Channel -- Maximum LOS range mi(km)Frequency Band Modulation Mode Integrated (7dBi) Reflector Dish (19dBi)

2.4 GHz

256QAM – MIMO-B (8X) 1.1 (1.7) 4.3 (6.9)64QAM – MIMO-B (6X) 2.4 (3.9) 9.5 (15.3)16QAM – MIMO-B (4X) 5.4 (8.6) 21.3 (34.3)

QPSK – MIMO-B (2X) 10.7 (17.2) 40 (64)QPSK – SISO (1X) 15.1 (24.3) 40 (64)


PMP 450 @ 3 GHZTHROUGHPUT AND RANGE PERFORMANCE

14

Modulation Mode

Sensitivity (dBm)

T-put (Mbps)

CNR (dB)


256QAM – MIMO-B (8X) -64 128 32

20 MHz Channel -- Maximum LOS range mi(km)Frequency Band Modulation Mode Integrated (9dBi) Reflector Dish (12dBi)

3 GHz

256QAM – MIMO-B (8X) 1.2 (2.0) 4.4 (7.0)64QAM – MIMO-B (6X) 2.8 (4.4) 9.8 (15.8)16QAM – MIMO-B (4X) 6.2 (9.9) 21.9 (35.3)

QPSK – MIMO-B (2X) 12.2 (19.6) 40 (64)


VOIP AND VIDEO TESTING

15

VoIP Testing:- Tested G.711u and G.729 codecs- Shown is the maximum number of simultaneous calls while maintaining a MOS score >3.5

Video Testing:- Preliminary testing showed good results

- No issues when sending multiple HD (H.264) streams

- Surveillance use case also tested well- New Features enable IPTV

# SMs G.711u G.729

1 60 60

4 120 128

# SMs G.711u G.729

1 60 60

4 100 100

VoIP Calls on unloaded system

With background traffic

Background Traffic

# Streams Frame Loss

No 4 0

Yes 4 0

# SMs UL/DL Ratio # Streams T-put (Mbps)

1 85/15 8 51.8

Streaming Video - Downlink

Video Surveillance - Uplink

(bi-directional FTP session)


MULTICAST VIRTUAL CIRCUIT

• New feature on PMP 450 enables multicast traffic to be properly prioritized

• Previously multicast packets were transmitted as part of the Broadcast VC (1X)

• If the Multicast VC is enabled, multicast packets can be transmitted downlink at a configurable data rate (1X, 2X, 4X, 6X) on a separate VC.

16

Enabled under Configuration Radio

Multicast Downlink CIR: Guaranteed multicast VC bandwidth, this includes the repeat count as part of the multicast bandwidth. This is calculated separately from the Broadcast CIR.


• Complement PMP 450 with VoIP!

• Clean setup with power supply through WAN port for PMP450 and ePMP RM.

• 2 FXS ports• Feature rich ATA with built-in router:

C3VOIP-150

17

Feature C3VoIP-150Model Number N000000L020A

FXS Port 2, RJ11LAN Port 1, RJ45WAN Port 1xFE, RJ45

Proprietary PoEAC/DC adaptor AC input: 110-240V,

DC output:12V, 2ABridge mode Bridge/RouterVoice Codec G.711a, G.711µ, G.722,

G.723, G.729 A/AB Fax Over IP T.38 compliant / G.711

Auto Provision TFTP/HTTP/HTTPS, TR069QoS 802.1Q/802.1p VLAN,

IP TOSManagement SNMPv2, CNS support

• Comprehensive voice codecs: G.711 & G.729A/B, adaptive jitter buffer management, echo cancellation, T.38 Fax.

• Advanced call features including 3-way conference, music on hold, call hold/forwarding/mute/transfer, speed dial, caller ID, black list , call log, etc.

• Secure and automated provisioning using HTTP/HTTPS/TFTP, TR069


CAMBIUM FIELD TRIAL RESULTS

BETA FIELD TEST – LOS

11.8 miles11.8 miles

3.95 miles3.95 miles

2.4 miles2.4 miles

Remote Name Distance from AP

Est. Elevation of SM

SM Rx Power

SM Tx Power

SNR @ the SM

Link Test Aggregate

Link Test Downlink

Link Test Uplink

SM 1 2.4 miles 100 feet -65 dBm 18 dBm 31 86.1 Mbps 65.8 Mbps 20.3 Mbps



APSW Version R12.0Elevation 320 feetAntenna 60° (MIMO/FSK)Frequency 5800 MHzDuty Cycle 75% D/L

CAMBIUM NETWORKS, LTD. CONFIDENTIAL RESTRICTED19© 2014 Cambium Networks, Inc. All rights reserved.

BETA FIELD TESTING - NLOSModulation Mode Rx Pwr Lvl

(dBm)SM

Ant Ht (ft)T-put DL/UL

(Mbps)Notes

QPSK – MIMO-B (2X) -80 19 21/6 NLOS (trees directly in front)

16QAM – MIMO-B (4X) -70 60 32/16 NLOS / nLOS (near tree tops, some blockage)

64QAM – MIMO-B (6X) -65 90 39/22 nLOS (Fresnel zone interference, can see AP)

Test Setup Parameter

3.7 Mile Link SM with reflector

AP Tx Output Power 19 dBm

Duty Cycle 75% down

CAMBIUM NETWORKS, LTD. CONFIDENTIAL RESTRICTED20© 2014 Cambium Networks, Inc. All rights reserved.

PMP 450 CHICAGO URBAN CANYON TRIALSCENARIO #1

RM(NLOS) : ● 0.36 miles● 22dBm w/ integrated antenna● Rx : -64dBm● Aggregate Tput : 25.2Mbps

RM (nLOS) :● 0.22 miles● 22dBm w/ integrated antenna● Rx : -64dBm● Aggregate Tput : 29.2Mbps

RM (LOS) :● 0.22 miles● 19dBm w/ Cassagrain● Rx : -56dBm● Aggregate Tput : 99.5Mbps

CAMBIUM NETWORKS, LTD. CONFIDENTIAL RESTRICTED


PMP 450 CHICAGO URBAN CANYON TRIALSCENARIO #2

AP(NLOS) facing South : ● 90° degree MIMO antenna● Height approximately 25ft.● Started at corner of the block and maintained performance after moving 300ft further away

RM(NLOS) facing East :● 0.13 miles away● Blocked by 8 story building on the left● Installed with Cassagrain● SM Rx : -76dBm● Aggregate Tput : 33.6Mbps

22© 2014 Cambium Networks, Inc. All rights reserved.CAMBIUM NETWORKS, LTD. CONFIDENTIAL RESTRICTED

PMP 450 PLATFORM FEATURES

PMP RELEASES – WHERE WE’VE BEEN

24

2012 20134Q 1Q 2Q 3Q 4Q

R12.0.1• 5.4 GHz ETSI• 10 MHz Channels• Alignment Tone

R12.0.3.1• Full Spectrum Band

Scan (across channel sizes and frequencies)

• PPPoE PADI filtering• CIR• AP Selection Method• Link Stability Updates

Released

In-process

R12.0• Initial Release• 5.8 GHz• MIMO-B Operation• 20 MHz Channels• GPS Sync• Up to 90 Mbps

Product concepts described in this presentation may still be under investigation or development. Specific details, specifications and timelines are subject to change without notice. Cambium makes no commitment or representation that such product concepts will be available as commercial products.

Jan, 2014

R12.0.2• 5.4 GHz FCC• Maximum Burst Rate controls• RADIUS dictionary updates• 128-bit AES Encryption• Fully Scalable (to 238 RMs)• Enhance Radio Statistics (Rx

Pwr, Signal strength, Signal to Noise status)

R12.1• Autosync• Enhanced Spectrum

Analyzer• NTP Server in AP• Rx Quality Statistics• Enhanced Link Test• IP Access Filtering

R12.1.3• 2.4 GHz AP & RM• Connectorized RM• AP Bridge Flooding• Simplified Sync (Remote AP)• Vietnam Region code• 2.5 MHz Channel Raster

R12.2.2• PMP 430 interoperability• QPSK SISO mode• 256 QAM• Larger MTU (1700 bytes)• Improved QoS Handling


Feature Benefit

PMP 430 interoperability

Interoperability of PMP 450 AP and PMP 430 SM. A PMP 430 SM can register and co-exist in a PMP 450 sector

QPSK SISO mode The AP can transmit at 3 dB higher power, rate adapting down to QPSK SISO mode of operation when channel conditions demand it

256 QAMPMP 450 can rate adapt up to 256-QAM modulation rates (8x) when channel conditions allow it, giving a total of 125 Mbps capacity

Larger MTU (1700 bytes)

PMP 450 now supports up to 1700 byte packets, allowing the use of MPLS tags in the ethernet structure

Enhanced Link Test Statistics

Additional statistics are available after link test is run to better analyze the link

PMP 450 R12.2 SOFTWARE RELEASE


PMP 450 INTEROPERABILITY

26

PMP 430 RM

PMP 430 RM

PMP 430 RM

PMP 430 RM

PMP 450 RM

PMP 450 RMPMP 430 APPMP 450 AP

When PMP 430 Interoperability becomes available:

Simply swap Access Points, then continue to build out your network by adding PMP 450 RMs


PMP 450 – CONTINUAL PERFORMANCE EVOLUTION

27

More Frequency Bands

256 QAM

Processing Improvements

Larger MTU Size

QoS

2.4 GHz3.5 GHz3.65 GHz

90 => 125 Mbps Throughput

Higher PPS

1700 Byte MTU

Strict Priority Support

Spectrum Agile Architecture Capable of Operating Down to 400 MHz

Enhanced Area-Averaged Capacity

Higher Capacity Enterprise LinksHigher Capacity For VoIP-Intensive Applications

MPLS Tag-Friendly

Predictable Performance in Overload Conditions

*Roadmap features, subject to change© 2014 Cambium Networks, Inc. All rights reserved.

pmp 450 update for pricing contact maplenet wireless maplenet wirelessmaplenet wireless february...

Documents