Filter Head/Cap

Filter

Filter Sump

*

INSTRUCTIONS

Step 1—Locate * Filter Housing assembly.

1. Includes filter housing, mounting clip and screw and filter.

2. Make sure you have the tools to cut tubing and make the necessary plumbing connections. This Inline system can be used to connect to the water supply that connects to the back of your refrigerator or as a stand-alone drinking water system that connects to a separate drinking water faucet (not included).

NOTE: This filter is for cold water use only and is not designed to connect directly to a kitchen faucet.

Plumbing Connections are 1/4” push-fittings.

Step 2 - Install Filter

1. Select a suitable location for the filter system under the sink or behind the refrigerator. Location should be reasonably accessible for filter replacement.

2. Install the single mount clip if necessary in a suitable location using the included screw.

NOTE: The flow of water is from the bottom “Inlet” and exits the “outlet” at the Filter Head/Cap end.

NOTE: When mounting housing to a cabinet make sure to leave enough space below sump for removal of sump (approx. 3 in) for maintenance.

Step 3

1. Unscrew filter head/cap.

2. Insert filter into opening on top of the filter cartridge.

3. Insert filter cartridge into the filter sump.

4. Thread the filter cap onto the filter sump and screw on tight.

It is recommended that a water shut off valve is used with this unit to manually turn the water on or off for easy servicing.

After installation or servicing, check the inlet & outlet for leaks to ensure the tubing is installed properly into the 1/4” push fit connectors.

Pr purTM

INLINECONNECT

SERIES

Customer Service: 800-544-3533 www.propurusa.com Pr purTM

PP100-IC for use with refrigerator

Step 5- Install the Faucet

1. Select a suitable location for the drinking water faucet as close to the sink as possible allowing convenient space under the sink for assembly. Drill the sink top with a 1/2” bit to accommodate the inlet pipe.

2. Assemble the faucet to the sink top:

i. Remove the push fit adaptor, the brass nut and the lock washer from the inlet pipe.

ii. Insert the valve through the sink top to seat the rubber washer.

iii. Replace the lock washer and brass nut and tighten firmly with a wrench.

iv. Replace the push-fit adaptor.

Step 4 - Install the EZ Adaptor

1. Turn off the cold water supply valve under the sink. If there is no valve, turn off the water to your house at the main meter.

2. Open the cold water faucet to let off pressure. Make sure the valve is off and the faucet is not dripping.

3. Unscrew the nut that holds the cold water supply line into the pipe where you just turned the water off from.

4. Install the EZ adaptor on the exposed threads and tighten.

5. Reinstall the nut with the cold water supply line onto the top of the EZ adaptor fitting and tighten.

NOTE: Do NOT turn the cold water line back on yet, the water will flow directly out of the EZ adaptor and flood your kitchen.

Step 6 - Install Connecting Tube

1. Cut two pieces of the 1/4” plastic tubing to fit between the plastic push fittings on:

a. the EZ adaptor and the filter head inlet.

b. the filter head outlet and the faucet.

NOTE: Allow an extra 1” inch on each piece as the tip of the tubing will travel about 1/2” into each fitting to seat properly.

2. Seat the tubing firmly into the push-fit plastic adaptors on the EZ adaptor, the filter head and the faucet.

Step 7 - Start-Up

1. Open the tap fully by lifting the lever to its vertical position to allow trapped air and water to flow out of the system.

2. Using the EZ adaptor, turn water on at the main inlet of the cold water sup-ply. Water should start flowing out of the faucet once the filter system has filled with water– within 30 seconds

3. Flush the system for one to two minutes before using the water, some residu-al particles may be expelled during this flush; this is normal.

Fully Installed DIY System

Customer Service: 800-544-3533 www.propurusa.com

For use with safe treated potable water sources.

Replacement Filters:

Rated Service Flow: 0.6 gallons per minute

Maximum Working Pressure: 125 psig

Maximum Operating Temperature: 100°F

Optional Steps for Use with dedicated drinking faucet

PP100-IC-RF

Pr purTM

LIMITED WARRANTY Propur warrants this product to be free from defects in material and manufacture for a period of 3 years from date of purchase to the end-user. This includes the head and bracket, cap, fi lter mount and housing. O-rings should be replaced if there are any signs of damage.

Filter is warranted for a period of 3 months from date of purchase against defects in workmanship only.

PROPUR MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOMER OR USAGE OF TRADE. If the product fails to sa sfy the limited warranty during the warranty period, PROPUR will repair or replace the product at its discre on.

THIS WARRANTY DOES NOT COVER ANY LABOR.

Limita on of Liability:PROPUR will not be liable for any loss or damage arising from this product, whether direct, indirect, special, incidental, or consequen al, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. Some states and countries do not allow the exclusion or limita on of incidental or consequen al damages, so the above limita on or exclusion may not apply to you.

Customer Service: 800-544-3533 www.propurusa.com Pr purTM

TM

TM

TM

TM