procash 2150xe short installation manual -...
TRANSCRIPT
Short installation manual
SPECIFIKATIONS SPECIFIKATIONS
GENERAL SPECIFIKATIONS
Physical Security
Alarm Protection
Power Requirements
Network structure
Power Usage for ATM without UPS
Dimensions and Weight of Unit with installation frame
with Safe
Single Cable Run Constrains
Single Cable Installation Constrains
This ATM meets the following Security standards EN 60950, UL60950 and meets the attack test per UL 291-15, CSA C22.2-60950, IEC 60950. The safe door has a relocking feature. The controlling of safe door is by keys, combination lock with keys or optional electronic lock.
Height
Recommended Installation Height
Width
Depth
Depth with fascia frame (Wodden Support Table)
Weight
Surface Load
Foot print
Operation and Maintenance Area (Front Load)
Operation and Maintenance Area (Rear Load)
Fan capacity
Fore more Details regarding Installation not covered in this document we refer to Reference Installation Guide with order no.: 01750058423
The following chart sitemizes the physical spacing requirements of the signal cable run with respect to order power and electrical equipment cable run.
Type of electrical run
Fluorescent, neon incandescent lighting fixture
Unshielded power line or electrical equipment
Unshielded power line or electrical equipment with signal cables enclosed in grounded conduit
Power line in grounded conduit with signal cables in grounded conduit
1/2”
3/4”
1”
1 1/4”
1 1/2”
2”
Conduit size (inches)
0,622
0,824
1,049
1,38
1,61
2,067
Internal diameter (inches)
100%
0,3
0,53
0,86
1,5
2,04
3,36
33%
0,099
0,175
0,283
0,495
0,679
1,109
40%
0,12
0,21
0,34
0,6
0,81
1,34
25%
0,075
0,132
0,215
0,375
0,51
0,84
Area square inches
Relative care is required when installing signal cables in conduits. Unlike power and lightening cables, signal cables have small conductors and light isolations and will not withstand as much strain in installation. The following chart summarizessome common conduit parameters. The sum of crosssectional areas of cables being installed in conduit should not exceed 40% of the area of the conduit.
Below 2 kVA
127 mm (5”)
127 mm (5”)
64 mm (2 1/2”)
30 mm (1 3/16”)
Power of electrical run
Between 2-5 kVA
127 mm (5”)
305 mm (12”)
152 mm (6”)
76 mm (3”)
Above 5 kVA
127 mm (5”)
610 mm (2”- 0”)
305 mm (12”)
152 mm (6”)
1391 mm (54.76 “)
NA
790 mm (31.1”)
1213 mm (47.76”)
NA
907 kg (1999.94 lb)
15.8kN/m²(2.3lb/in²)
0,6 m² (6.46 ft²)
NA
2.3 m² (24.75 ft²)
60m³/h(2118.6 ft³/h)
1087 kg (2396.84 lb)
20.1kN/m²(3.0lb/in²)
0,6 m² (6.46 ft²)
NA
2.3 m² (24.75 ft²)
60m³/h(2118.6 ft³/h)
1057 kg (2330.69 lb)
19.6kN/m²(2.9lb/in²)
0,6 m² (6.46 ft²)
NA
2.3 m² (24.75 ft²)
60m³/h(2118.6 ft³/h)
IP 54 / IP 20
4.2 / 2.6 A455 / 435 VA400 / 385 W
NAI
6.4 / 6.4 mANA
NA
TN
UL 291 Business UL 291 CEN III CEN IVThis ATM meets the following EMC standards EN 55 022 class B, EN55024, EN 50082-1, EN 50082-2, EN61000-3-2, EN61000-3-3, FCC CFR 47, part 15 subpart B class A, ICES-003 (CSA 108.8) and BSMI-Standard CNS 13438 class B.The CE symbol indicates that the product complies with the following EU directives. EMC 89/336/ECC, 91/263/ECC, 92/31/ECC and 93/68/ECC and on Low voltage directive / security 73/23/ECC and 93/68/ECC.The ATM requires a single-phase three-wire unswitched power outlet. Wiring to the ATM must use a third-wired earth ground (conduit ground is not acceptable). The power supplied must be as specified below:110 - 120 / 220 - 240 VAC (- 10 to + 6 %) at 50/60 Hz (+/- 1%), single phase
The UL - listed safe is equipped with a basic alarm sensor package. The package includes a safe cabinet door open switch. Optional seismic sensor.
Each ATM must have a dedicated outlet/circuit.Power to the ATM may be a branch or dedicated service and must be protected by a safety quick-disconnect device the break line voltage (such a circuit breaker at the electrical service panel). The quick disconnect device (or circuit breaker) must turn off the line voltage at the amperage specified below.Fuse for the Device 110-120 VAC service, disconnect at 10 ampsor Fuse 220-240- VAC service, disconnect at 10 ampsDegree of Protection (EN 60529) Outdoors / IndoorsOther electronic devices sharing power on a common branch circuit must conform to the same conducted interference standards as the ATM.
Rated Current Consumption (Maximum Operation) 110-120 VAC / 220-240 VACApparent Power Consumption (Maximum Operation) 110-120 VAC / 220-240 VACReal Output 110-120 VAC / 220-240 VACPower factor 110-120 VAC / 220-240 VACProtection ClassLeakage Current (Maximum) 110-120 VAC / 220-240 VACApparent Power Consumption open circuit
Rated Current Consumption (Maximum Operation) 110-120 / 220-240 VACApparent Power Consumption (Maximum Operation) 110-120 / 220/240 VACReal Output 110-120 VAC / 220-240 VACPower factorProtection ClassLeakage Current (Maximum) 110-120 VAC / 220-240 VACStandby Power Consumption (no transaction)
ProCash 2150xe ProCash 2150xe
Finish
Operating Environment (DIN EN 60721(IEC 721))
Mechanical Environment (DIN EN 60721(DIN IEC 721))
Environmental Protection (SN3230 / 1/ )
Noise emission in accordance with DIN EN 27779 / Noise rating according to ISO 92966.1 B / 6.9 B
44 dB / 51 dB
Fascia painted standard WN Grey (option any NCS or RAL color or stainless steel)Housing (Top Cover) painted standard WN Grey (option any NCS or RAL color) Safe painted standard Grey (option any NCS or RAL color)
Temperature, Safe location Class 3K3 (Inside) + 5 to + 35 °C (41 to 95 F)Relative Humidity (Non Condensing) (Inside) 10 to 75 %Temperature, Fascia location (Outside with heating) -40 to + 50 °C ( -40 to 122 F)Relative Humidity (Non Condensing) (Outside) 10 to 75 %Temperature, Limited range of Operation (inside, only a short time of Operation Class 3K3) +5 to +40 °C (41 to 104 F)Relative Humidity, Limited range of Operation (inside, only a short time of Operation Class 3K3) 5 to 85 %Transport Class 2K2, Temperature -25 to + 60 C (-13 to 140 F)Transport Class 2K2, Relative Humidity 15 to 98 %Storage Class 1K2, Temperature + 5 to + 40 °C (41 to 104 F)Storage Class 1K2, Relative Humidity 5 to 85 %
Operation Standalone Unit Class 3M2Operation Desktop Unit Class 3M3Transport (In Original packing, on Vehicle, trailer, boat, train, and Air) Class 2M2Storage (In Original Packing) Class 1M3
Environmental Protect ion (Recycl ing)
Sound power level LWAd Standby / OperationWork place specific Sound pressure level LpAm Standby / Operation
Power Usage for ATM with UPS
For conduit runs 15.25 meters to 30.5 meters ( 50 to 100 feet), not External cablingmore than 33 % of conduit area should be used. Each 90 degree Please refer to the appropriate ATM Installation Guide for details conduit bend may be estimated as equal to the friction of a 9.15 for terminal cable access. Junction boxes, conduit, etc, are the meters (30 foot) length straight level conduit. If more than two 90 responsibility of the customer. Local codes will dictate location and degree bends are used in conduit run, insert a pull box. material to be used in electrical connections.Electro static discharge Negativ pressure constraintsStatic electricity charges are built up as a result of contact with To prevent cold weather operating problems due to induction of certain floor covering and furniture. A discharge of this build up can outside air and accompanying incursion of dirt, ATM should be discomfort housed in a positive pressure environment, however negative to people and possible interference with electronic devices. The (vacuum) not exceeding (.05") H2O is acceptable. Tall buildings following precautions should be taken whenever possible to are especially prone to having negative pressure values greater reduce the chance of static discharge problems. Avoid relative than (.05") special engineering will be required if this specified humidity values less than 40 %. Treat floor covering around pressure is exceededelectronic equipment with static reducing agents commercially available.
ProCash 2150xe
NA
NA
NA
NA
NA
NA
4.2 / 2.6 A455 / 435 VA
1365 / 1314 BTU/hNAI
6.4 / 6.4 mANA
Heating (without device)
Rated current consumption 110-120 VAC / 220-240 VACApparent power consumption 110-120 VAC / 220-240 VACActive power 110-120 VAC / 220-240 VAC
4.5 / 2.2 A545 / 500 VA545 / 500 W
4.5 / 2.2 A545 / 500 VA
1860 / 1707 BTU/h
3.2 / 1.65 A340 / 320 VA
1010 / 970 BTU/h0.93 / 0.88
I1.2 / 1.2 mA
NA
3.2 / 1.65 A340 / 320 VA296 / 284 W0.93 / 0.88
I1.2 / 1.2 mA
NA
Pro
Ca
sh
21
50
xe V
ers
ion
0.8
/
ProCash 2150xe
Short installation manual
Drawings is not drawn to scale.
All Demissions in Milimeter and (Inches).
Weight in Kilo and (Pound).
All Dimensions, Weight and Design, is
subject to change without notice.
Fore optional installation the inside floor level
and the outside floor level has to be the
same, if not adjustment has to be done
according to the height difference.
View of Device without illuminated signage
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Pro
Ca
sh
21
50
xe V
ers
ion
0.8
770
(30.
31")
98)
3(
"
7
8.
6 2
5 7
(9
)5"
2.
75
95"
(.
)
2
35 (8"
31
).
1
2
x. 0
ma
63m
. 17
(x
.1")
a
4
5 6
0
(.5
)
259"
70
0 (
27
.56
")
15
80
(6
2.2
")
88
0 (
34
.65
")
Wall holeMinimum Service Area
Ve
ntil
atio
n s
pa
ce
Op
era
tion
an
d m
ain
ten
an
ce s
pa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
sp
ace
, rig
ht o
r le
ft
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce if
a
CC
DM
is u
sed
or
ad
diti
on
al
inst
alla
tion
spa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce w
he
n a
1
350
(13.78")
800 (31.5")
85
0 (
33
.46
")
84
8 (
33
.39
")
83
0 (
32
.68
")
75
0 (
29
.53
")
790* (31.1")
15
95 (3.74")
1190 (46.85")
(700 - 27.56" **)
5050
95
0 (
37
.4")
395
(15.55")
(1.97")(0.59")
(1.97")
350
(13.78")
1 W
all
*
Wid
th o
f d
evi
ce h
ea
d **
Wid
th o
f sa
fe
A
C
B
D
630 (24.8")
584 (22.99")
539 (21.22")
471 (18.54")
179
72
(2
.83
")
97
(3
.82
")
14
9 (
5.8
7")
22
9 (
9.0
2")
64
4 (
25
.35
")
68
7 (
27
.05
")
72
4 (
28
.5")
84
2 (
33
.15
")
694 (27.32")
237 (9.33")
481 (18.94")
(7.05")
46(1.81")
ma
x.3
60
(1
4.1
7")
650 (25.59")
329 (12.95")359 (14.13")
36
8 (
14
.49
")
8
1
2
42
1
3
3
7
6 6 6
5
5
9
11 1110
DC
BA
50(1.97")
ma
x.3
60
(1
4.1
7")
650 (25.59")
329 (12.95")359 (14.13")
36
8 (
14
.49
")
630 (24.8")
584 (22.99")
539 (21.22")
469 (18.46")
179
72
(2
.83
")
97
(3
.82
")
12
2 (
4.8
")
19
2 (
7.5
6")
63
7 (
25
.08
")
68
7 (
27
.05
")
73
7 (
29
.02
")
84
2 (
33
.15
")
694 (27.32")
(7.05") 8
6 6 6
51
2
42
1
3
3
5
7
9
11 1110
700 (27.56")
88
5 (
34
.84
")
230
848 (33.39")
13
91
(5
4.7
6")
17
50
(6
8.9
")
62
8 (
24
.72
")
68
3 (2
6.8
9") 13
33
(5
2.4
8")
13
98
(5
5.0
4")
72/43*
1213 (47.76")
1248 (49.13")
(9.06")
(2.83"/1.69"*)
73
6 (
28
.98
")
79
0 (
31
.1")
60
0 (
23
.62
")
15
(0
.59
")
* S
tan
da
rd lo
ck: 4
3 m
m (
1.6
9")
C
usto
me
r-sp
ecifi
c lo
ck: 7
2 m
m (
2.8
3")
8
9
11 11
6
2
A
C
B
D
2
10
3
3
4
ma
x.3
60 (
14
.17")
650 (25.59")
329 (12.95")359 (14.13")
37
1 (
14
.61
")
158
(6.2
2")
550 (21.65")
466 (18.35")
138
(5.43")
9
4
588
(2
3.1
5")
63
8 (
25
.12
")
83
6 (
32
.91
")
688 (27.09")
188 (7.4")
500 (19.69")
20
8 (
8.1
9")
(3.7
")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)X
2
X1
X3
(min
. 1
.57
")
(min
. 4.9
2")
3 2
4 5 6
1
7
8
I:
(m
in. 1
,57
")
(0.9
8")
(min
. 4.9
2")
min
. 40
25
min
. 125
x 5
x 2
2 9 5 61
3
7
II:
1 Safe
2 Mounting set for safe
3 Tear-off sensor
4 Screed
5 Concrete
6 Mounting set for
installation frame
7 Top surface of finished floor 10 Installation frame 222mm (8.74")
8 Installation rack
9 Installation frame 25mm (0.98")
* This distance depends on the screed height. The threaded rod included
22
2 (
8.7
4")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)
(min
. 1
.57
")
(min
. 4
.92
")
3
4 5 6
2
1
10
7
III :
1 O
uts
ide
wa
ll
2 In
sid
e w
all
(de
vice
sid
e)
I: II: III:
Vertical view of wall installation
Installation rackMounting structure with UL safe
tunnel width 35 mm - 1.38"
1 Device
2 Wall
3 Floor inside
4 Floor outside
5 Possible variants see down here
x1
x2
5
06
(19
.92
")
65
8 (
25
.91
")
70
0 (
27
.56
")8
80
(3
4.6
5")
95
0*
(37
.4"*
)
17
50
(6
8.9
")
max. 360(max. 14.17")
1
2
2
3
4
5
Installation Frame 25mm (0.98") Installation Frame 222mm (8.74")
Short installation manual
Drawings is not drawn to scale.
All Demissions in Milimeter and (Inches).
Weight in Kilo and (Pound).
All Dimensions, Weight and Design, is
subject to change without notice.
Fore optional installation the inside floor level
and the outside floor level has to be the
same, if not adjustment has to be done
according to the height difference.
Ve
ntil
atio
n s
pa
ce
Op
era
tion
an
d m
ain
ten
an
ce s
pa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
sp
ace
, rig
ht o
r le
ft
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce if
a
CC
DM
is u
sed
or
ad
diti
on
al
inst
alla
tion
spa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce w
he
n a
1
350
(13.78")
800 (31.5")
85
0 (
33
.46
")
84
8 (
33
.39
")
83
0 (
32
.68
")
75
0 (
29
.53
")
790* (31.1")
15
95 (3.74")
1190 (46.85")
(700 - 27.56" **)
5050
95
0 (
37
.4")
395
(15.55")
(1.97")(0.59")
(1.97")
350
(13.78")
1 W
all
*
Wid
th o
f d
evi
ce h
ea
d **
Wid
th o
f sa
fe
5 7
(.2 95")
75
2")
.95(
5 3
(8")
.31
987
(38.
86")
40 (1.
57")
")
3 2
.
7
8
68 9
(
848 (33.39")
13
91
(5
4.7
6")
17
50
(6
8.9
")
88
5 (
34
.84
")
62
8 (
24
.72
")
68
3 (2
6.8
9")
13
33
(5
2.4
8")
16
15
(6
3.5
8")
72/43*
1213 (47.76")
1248 (49.13")
230
(9.06")
(2.83"/1.69"*)
586 (23.07")
700 (27.56")
40
(1.5
7")
73
6 (
28
.98
")
79
0 (
31
.1")
60
0 (
23
.62
")
15
(0
.59
")
* S
tan
da
rd lo
ck:
43
mm
(1
.69
")
Cu
sto
me
r-sp
ecifi
c lo
ck:
72
mm
(2
.83
")
ProCash 2150xetunnel width 35 mm - 1.38"
1
2
x. 0
ma
63m
. 17
(x
.1")
a
4
5 6
0
(.5
)
259"
70
0 (
27
.56
")
15
80
(6
2.2
")
88
0 (
34
.65
")
Wall holeMinimum Service Area
1 O
uts
ide
wa
ll
2 In
sid
e w
all
(de
vice
sid
e)
Vertical view of wall installation
1 Device
2 Wall
3 Floor inside
4 Floor outside
5 Possible variants see down here
x1
x2
5
06
(19
.92
")
65
8 (
25
.91
")
70
0 (
27
.56
")8
80
(3
4.6
5")
95
0*
(37
.4"*
)
17
50
(6
8.9
")
max. 360(max. 14.17")
1
2
2
3
4
5
View of Device with illuminated signage
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Pro
Ca
sh
21
50
xe V
ers
ion
0.8
A
C
B
D
630 (24.8")
584 (22.99")
539 (21.22")
471 (18.54")
179
72
(2
.83
")
97
(3
.82
")
14
9 (
5.8
7")
22
9 (
9.0
2")
64
4 (
25
.35
")
68
7 (
27
.05
")
72
4 (
28
.5")
84
2 (
33
.15
")
694 (27.32")
237 (9.33")
481 (18.94")
(7.05")
46(1.81")
ma
x.3
60
(1
4.1
7")
650 (25.59")
329 (12.95")359 (14.13")
36
8 (
14
.49
")
8
1
2
42
1
3
3
7
6 6 6
5
5
9
11 1110
DC
BA
50(1.97")
ma
x.3
60
(1
4.1
7")
650 (25.59")
329 (12.95")359 (14.13")
36
8 (
14
.49
")
630 (24.8")
584 (22.99")
539 (21.22")
469 (18.46")
179
72
(2
.83
")
97
(3
.82
")
12
2 (
4.8
")
19
2 (
7.5
6")
63
7 (
25
.08
")
68
7 (
27
.05
")
73
7 (
29
.02
")
84
2 (
33
.15
")
694 (27.32")
(7.05") 8
6 6 6
51
2
42
1
3
3
5
7
9
11 1110
8
9
11 11
6
2
A
C
B
D
2
10
3
3
4
ma
x.3
60 (
14
.17")
650 (25.59")
329 (12.95")359 (14.13")
37
1 (
14
.61
")
158
(6.2
2")
550 (21.65")
466 (18.35")
138
(5.43")
9
4
588
(2
3.1
5")
63
8 (
25
.12
")
83
6 (
32
.91
")
688 (27.09")
188 (7.4")
500 (19.69")
20
8 (
8.1
9")
(3.7
")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)X
2
X1
X3
(min
. 1
.57
")
(min
. 4.9
2")
3 2
4 5 6
1
7
8
I:
(m
in. 1
,57
")
(0.9
8")
(min
. 4.9
2")
min
. 40
25
min
. 125
x 5
x 2
2 9 5 61
3
7
II:
1 Safe
2 Mounting set for safe
3 Tear-off sensor
4 Screed
5 Concrete
6 Mounting set for
installation frame
7 Top surface of finished floor 10 Installation frame 222mm (8.74")
8 Installation rack
9 Installation frame 25mm (0.98")
* This distance depends on the screed height. The threaded rod included
22
2 (
8.7
4")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)
(min
. 1
.57
")
(min
. 4
.92
")
3
4 5 6
2
1
10
7
III :
I: II: III:
Installation rackMounting structure with UL safe Installation Frame 25mm (0.98") Installation Frame 222mm (8.74")
Short installation manual
Drawings is not drawn to scale.
All Demissions in Milimeter and (Inches).
Weight in Kilo and (Pound).
All Dimensions, Weight and Design, is
subject to change without notice.
Fore optional installation the inside floor level
and the outside floor level has to be the
same, if not adjustment has to be done
according to the height difference.
Ve
ntil
atio
n s
pa
ce
Op
era
tion
an
d m
ain
ten
an
ce s
pa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
sp
ace
, rig
ht o
r le
ft
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce if
a
CC
DM
is u
sed
or
ad
diti
on
al
inst
alla
tion
spa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce w
he
n a
1 W
all
*
Wid
th o
f d
evi
ce h
ea
d **
Wid
th o
f sa
fe
* S
tan
da
rd lo
ck:
43
mm
(1
.69
")
Cu
sto
me
r-sp
ecifi
c lo
ck:
72
mm
(2
.83
")
700 (27.56") 848 (33.39")
13
91
(5
4.7
6")
17
50
(6
8.9
")
88
5 (
34
.84
")
62
8 (
24
.72
")
68
3 (2
6.8
9")
13
33
(5
2.4
8")
14
09
(5
5.4
7")
72/43*
1188 (46.77")
1248 (49.13")
(9.06")
230
(2.83"/1.69"*)
73
2 (
28
.82
")
79
0 (
31
.1")
60
0 (
23
.62
")
15
(0
.59
")
1
350
(13.78")
800 (31.5")
87
5 (
34
.45
")
350
(13.78")
84
8 (
33
.39
")
83
0 (
32
.68
")
75
0 (
29
.53
")
790* (31.1")
15
95 (3.74")
1190 (46.85")
(700 - 27.56" **)
5050
95
0 (
37
.4")
395
(15.55")
(1.97")(0.59")
(1.97")
603
(2. 6")
2"
(8 8
)
2 2
73
.
78
1 (
30
.75
")
3 (8
72.
)7"
ProCash 2150xetunnel width 60 mm - 2.36"
View of Device without illuminated signage Wall holeMinimum Service Area Vertical view of wall installation
1
2
x. 5
ma
33m
. 19
(x
.1")
a
3
5 6
0
(.5
)
259"
70
0 (
27
.56
")
15
80
(6
2.2
")
88
0 (
34
.65
")
1 O
uts
ide
wa
ll
2 In
sid
e w
all
(de
vice
sid
e)
1 Device
2 Wall
3 Floor inside
4 Floor outside
5 Possible variants see down here
x1
x2
5
06
(19
.92
")
65
8 (
25
.91
")
70
0 (
27
.56
")8
80
(3
4.6
5")
95
0*
(37
.4"*
)
17
50
(6
8.9
")
max. 335(max. 13.19")
1
2
2
3
4
5
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Pro
Ca
sh
21
50
xe V
ers
ion
0.8
A
C
B
D
630 (24.8")
584 (22.99")
539 (21.22")
471 (18.54")
179
72
(2
.83
")
97
(3
.82
")
14
9 (
5.8
7")
22
9 (
9.0
2")
64
4 (
25
.35
")
68
7 (
27
.05
")
72
4 (
28
.5")
84
2 (
33
.15
")
694 (27.32")
237 (9.33")
481 (18.94")
(7.05")
46(1.81")
ma
x.3
35
(1
3.1
9")
650 (25.59")
329 (12.95")359 (14.13")
34
3 (
13
.5")
8
1
2
42
1
3
3
7
6 6 6
5
5
9
11 1110
DC
BA
50(1.97")
ma
x.3
35
(1
3.1
9")
650 (25.59")
329 (12.95")359 (14.13")
34
3 (
13
.5")
630 (24.8")
584 (22.99")
539 (21.22")
469 (18.46")
179
72
(2
.83
")
97
(3
.82
")
12
2 (
4.8
")
19
2 (
7.5
6")
63
7 (
25
.08
")
68
7 (
27
.05
")
73
7 (
29
.02
")
84
2 (
33
.15
")
694 (27.32")
(7.05") 8
6 6 6
51
2
42
1
3
3
5
7
9
11 1110
8
9
11 11
6
2
A
C
B
D
2
10
3
3
4
ma
x.3
35 (
13
.19")
650 (25.59")
329 (12.95")359 (14.13")
34
6 (
13
.62
")
158
(6.2
2")
550 (21.65")
466 (18.35")
138
(5.43")
9
4
588
(2
3.1
5")
63
8 (
25
.12
")
83
6 (
32
.91
")
688 (27.09")
188 (7.4")
500 (19.69")
20
8 (
8.1
9")
(3.7
")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)X
2
X1
X3
(min
. 1
.57
")
(min
. 4.9
2")
3 2
4 5 6
1
7
8
I:
(m
in. 1
,57
")
(0.9
8")
(min
. 4.9
2")
min
. 40
25
min
. 125
x 5
x 2
2 9 5 61
3
7
II:
1 Safe
2 Mounting set for safe
3 Tear-off sensor
4 Screed
5 Concrete
6 Mounting set for
installation frame
7 Top surface of finished floor 10 Installation frame 222mm (8.74")
8 Installation rack
9 Installation frame 25mm (0.98")
* This distance depends on the screed height. The threaded rod included
22
2 (
8.7
4")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)
(min
. 1
.57
")
(min
. 4
.92
")
3
4 5 6
2
1
10
7
III :
I: II: III:
Installation rackMounting structure with UL safe Installation Frame 25mm (0.98") Installation Frame 222mm (8.74")
Drawings is not drawn to scale.
All Demissions in Milimeter and (Inches).
Weight in Kilo and (Pound).
All Dimensions, Weight and Design, is
subject to change without notice.
Fore optional installation the inside floor level
and the outside floor level has to be the
same, if not adjustment has to be done
according to the height difference.
Ve
ntil
atio
n s
pa
ce
Op
era
tion
an
d m
ain
ten
an
ce s
pa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
sp
ace
, rig
ht o
r le
ft
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce if
a
CC
DM
is u
sed
or
ad
diti
on
al
inst
alla
tion
spa
ce
Ad
diti
on
al o
pe
ratio
n a
nd
ma
inte
na
nce
spa
ce w
he
n a
1 W
all
*
Wid
th o
f d
evi
ce h
ea
d **
Wid
th o
f sa
fe
* S
tan
da
rd lo
ck:
43
mm
(1
.69
")
Cu
sto
me
r-sp
ecifi
c lo
ck:
72
mm
(2
.83
")
1
350
(13.78")
800 (31.5")
87
5 (
34
.45
")
350
(13.78")
84
8 (
33
.39
")
83
0 (
32
.68
")
75
0 (
29
.53
")
790* (31.1")
15
95 (3.74")
1190 (46.85")
(700 - 27.56" **)
5050
95
0 (
37
.4")
395
(15.55")
(1.97")(0.59")
(1.97")
View of Device with illuminated signage Wall holeMinimum Service Area Vertical view of wall installation
1
2
x. 5
ma
33m
. 19
(x
.1")
a
3
5 6
0
(.5
)
259"
70
0 (
27
.56
")
15
80
(6
2.2
")
88
0 (
34
.65
")
1 O
uts
ide
wa
ll
2 In
sid
e w
all
(de
vice
sid
e)
1 Device
2 Wall
3 Floor inside
4 Floor outside
5 Possible variants see down here
x1
x2
5
06
(19
.92
")
65
8 (
25
.91
")
70
0 (
27
.56
")8
80
(3
4.6
5")
95
0*
(37
.4"*
)
17
50
(6
8.9
")
max. 335(max. 13.19")
1
2
2
3
4
5
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Puplished by
Wincor Nixdorf International GmbH
Banking Division Marketing
Heinz-Nixdorf-Ring 1
D-33106 Paderborn
Germany
Phone +49(0)5251/693 33 01
Fax +49(0)5251/693 59 18
http://www.wincor-nixdorf.com
c Wincor Nixdorf International GmbH
All Rights, including rights created by patent
grant or registration of a utility model or design,
are reserved.
Delivery subject to availability, subject to
change for technical reasons.
Pro
Ca
sh
21
50
xe V
ers
ion
0.8
A
C
B
D
630 (24.8")
584 (22.99")
539 (21.22")
471 (18.54")
179
72
(2
.83
")
97
(3
.82
")
14
9 (
5.8
7")
22
9 (
9.0
2")
64
4 (
25
.35
")
68
7 (
27
.05
")
72
4 (
28
.5")
84
2 (
33
.15
")
694 (27.32")
237 (9.33")
481 (18.94")
(7.05")
46(1.81")
ma
x.3
35
(1
3.1
9")
650 (25.59")
329 (12.95")359 (14.13")
34
3 (
13
.5")
8
1
2
42
1
3
3
7
6 6 6
5
5
9
11 1110
DC
BA
50(1.97")
ma
x.3
35
(1
3.1
9")
650 (25.59")
329 (12.95")359 (14.13")
34
3 (
13
.5")
630 (24.8")
584 (22.99")
539 (21.22")
469 (18.46")
179
72
(2
.83
")
97
(3
.82
")
12
2 (
4.8
")
19
2 (
7.5
6")
63
7 (
25
.08
")
68
7 (
27
.05
")
73
7 (
29
.02
")
84
2 (
33
.15
")
694 (27.32")
(7.05") 8
6 6 6
51
2
42
1
3
3
5
7
9
11 1110
8
9
11 11
6
2
A
C
B
D
2
10
3
3
4
ma
x.3
35 (
13
.19")
650 (25.59")
329 (12.95")359 (14.13")
34
6 (
13
.62
")
158
(6.2
2")
550 (21.65")
466 (18.35")
138
(5.43")
9
4
588
(2
3.1
5")
63
8 (
25
.12
")
83
6 (
32
.91
")
688 (27.09")
188 (7.4")
500 (19.69")
20
8 (
8.1
9")
(3.7
")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)X
2
X1
X3
(min
. 1
.57
")
(min
. 4.9
2")
3 2
4 5 6
1
7
8
I:
(m
in. 1
,57
")
(0.9
8")
(min
. 4.9
2")
min
. 40
25
min
. 125
x 5
x 2
2 9 5 61
3
7
II:
1 Safe
2 Mounting set for safe
3 Tear-off sensor
4 Screed
5 Concrete
6 Mounting set for
installation frame
7 Top surface of finished floor 10 Installation frame 222mm (8.74")
8 Installation rack
9 Installation frame 25mm (0.98")
* This distance depends on the screed height. The threaded rod included
22
2 (
8.7
4")
min
. 4
0
min
. 1
25
18
0*
(7.0
9"*
)
(min
. 1
.57
")
(min
. 4
.92
")
3
4 5 6
2
1
10
7
III :
I: II: III:
Installation rackMounting structure with UL safe Installation Frame 25mm (0.98") Installation Frame 222mm (8.74")
848 (33.39")
13
91
(5
4.7
6")
17
50
(6
8.9
")
88
5 (
34
.84
")
62
8 (
24
.72
")
68
3 (2
6.8
9")
13
33
(5
2.4
8")
16
30
(6
4.1
7")
72/43*
1188 (46.77")
1248 (49.13")
230 75 (2.95")
(9.06")
(2.83"/1.69")*
586 (23.07")
700 (27.56")
40
(1.5
7")
73
2 (
28
.82
")
79
0 (
31
.1")
60
0 (
23
.62
")
15
(0
.59
")
40 (1.
57") 2 9
").
7(
5
5
6 0
326
(.
")
8
3 2
."
72
82
(
)
7
7
)
32.8
"
(
96
2 (
37.8
7")
ProCash 2150xe
Short installation manual
tunnel width 60 mm - 2.36"