record assembled drawings.doc
TRANSCRIPT
-
8/10/2019 Record Assembled Drawings.doc
1/23
AIM:
To draw the given 2D Drawing of Knuckle Joint and also assemble the drawing usingAutoCAD 2000.
COMMANDS USED:
Limits oom
Line !otate
Circle "ol#lineArc $irror
Trim %ffset
Co '&lineDimlinear (illet
)*tend Dimradius
)rase 'ave!ectangle $ultiTe*t
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
2/23
RESULT:
Thus the given 2D Drawing of Knuckle Joint has been drawn and also assembled the
drawing using AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
3/23
AIM:
To draw the given 2D Drawing of "lummer ,lock and also assemble the drawing using
AutoCAD 2000.
COMMANDS USED:
Limits oomLine !otate
Circle "ol#line
Arc $irror Trim %ffset
Co '&line
Dimlinear (illet)*tend Dimradius
)rase 'ave
!ectangle $ultiTe*t
"ol#gon
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
4/23
RESULT:
-
8/10/2019 Record Assembled Drawings.doc
5/23
Thus the given 2D Drawing of "lummer ,lock has been drawn and also assembled thedrawing using AutoCAD 2000.
AIM:
To draw the given 2D Drawing of -niversel Cou&ling and also assemble the drawing usingAutoCAD 2000.
COMMANDS USED:
Limits oom
Line !otate
Circle "ol#lineArc $irror
Trim %ffset
Co '&lineDimlinear (illet
)*tend Dimradius
)rase 'ave!ectangle $ultiTe*t
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
6/23
-
8/10/2019 Record Assembled Drawings.doc
7/23
RESULT:
Thus the given 2D Drawing of -niversel Cou&ling has been drawn and also assembled
the drawing using AutoCAD 2000.
AIM:
To draw the given 2D Drawing of 'crew Jack and also assemble the drawing using
AutoCAD 2000.
COMMANDS USED:
Limits oom
Line !otateCircle "ol#line
Arc $irror
Trim %ffsetCo '&line
Dimlinear (illet
)*tend Dimradius)rase 'ave
!ectangle $ultiTe*t
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
8/23
-
8/10/2019 Record Assembled Drawings.doc
9/23
RESULT:
Thus the given 2D Drawing of 'crew Jack has been drawn and also assembled the drawing
using AutoCAD 2000.
AIM:
To draw the given 2D Drawing of (lange Cou&ling and also assemble the drawing using
AutoCAD 2000.
COMMANDS USED:
Limits oom
Line !otateCircle "ol#line
Arc $irror
Trim %ffsetCo '&line
Dimlinear (illet
)*tend Dimradius)rase 'ave
!ectangle $ultiTe*t
"ol#gon
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
10/23
RESULT:
-
8/10/2019 Record Assembled Drawings.doc
11/23
Thus the given 2D Drawing of (lange Cou&ling has been drawn and also assembled thedrawing using AutoCAD 2000.
AIM:
To draw the given 2D Drawing of Connecting !od and also assemble the drawing usingAutoCAD 2000.
COMMANDS USED:
Limits oom
Line !otateCircle "ol#line
Arc $irror
Trim %ffsetCo '&line
Dimlinear (illet
)*tend Dimradius
)rase 'ave!ectangle $ultiTe*t
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
After com&letion of assembled drawings save and &lot the drawing+
-
8/10/2019 Record Assembled Drawings.doc
12/23
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
13/23
RESULT:
Thus the given 2D Drawing of (lange Cou&ling has been and also assembled the drawing
using AutoCAD 2000.
AIM:
To draw the given 2D Drawing of Tail 'tock and also assemble the drawing using AutoCAD
2000.
COMMANDS USED:
Limits oomLine !otate
Circle "ol#line
Arc $irror Trim %ffset
Co '&line
Dimlinear (illet
)*tend Dimradius)rase 'ave
!ectangle $ultiTe*t
"ol#gon
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
-
8/10/2019 Record Assembled Drawings.doc
14/23
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
15/23
RESULT:
Thus the given 2D Drawing of Tail 'tock has been drawn and also assembled the drawing
using AutoCAD 2000.
AIM:
To draw the given 2D Drawing of 'team 'to& alve and also assemble the drawing using
AutoCAD 2000.
COMMANDS USED:
Limits oomLine !otate
Circle "ol#line
Arc $irror Trim %ffset
Co '&line
Dimlinear (illet
)*tend Dimradius)rase 'ave
!ectangle $ultiTe*t
"ol#gon
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
-
8/10/2019 Record Assembled Drawings.doc
16/23
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
17/23
RESULT:
Thus the given 2D Drawing of 'team 'to& alve has been drawn and also assembled thedrawing using AutoCAD 2000.
AIM:
To draw the given 2D Drawing of !amsbottom 'afet# alve and also assemble the drawingusing AutoCAD 2000.
COMMANDS USED:
Limits oom
Line !otate
Circle "ol#lineArc $irror
Trim %ffset
Co '&line
Dimlinear (illet)*tend Dimradius
)rase 'ave!ectangle $ultiTe*t
"ol#gon
PROCEDURE:
%&en the AutoCAD section from windows start u& menu +or deskto& shortcut+
'et the unit angle+ angle measurement+ angle direction and working area using
AutoCAD start u& menu+
'et the limit of screen using limit commands+
'et the 'na& on+ %sna& on+ %rtho off+
-
8/10/2019 Record Assembled Drawings.doc
18/23
'tart the &art drawing with the given drawing using ,asic commands and )diting
commands+
Assemble the &art drawing and mark the dimensions+
After com&letion of assembled drawings save and &lot the drawing+
Close the Drawing area and e*it from AutoCAD 2000
-
8/10/2019 Record Assembled Drawings.doc
19/23
RESULT:
Thus the given 2D Drawing of !amsbottom 'afet# alve has been drawn and also
assembled the drawing using AutoCAD 2000.
AIM:
To draw the front and cross section of the given !iveted La& Joint and also assemble using
AutoCAD 2000
COMMANDS USED:
Limits oom
Line $oveArc '&line
Trim (illetDimlinear Dimradius
PROCEDURE:
%&en the AutoCAD and set the re/uired limit+
(irst draw the igag !iveting b# using commands like Line+ Circle+ etc1
Cross section of the &late is done b# using hatch command+
e*t draw the chain riveting using commands+
"itch of rivet is measured b# using thickness of the &late of line calculation+
-
8/10/2019 Record Assembled Drawings.doc
20/23
Dimension of line is measured b# using dimension command.
-
8/10/2019 Record Assembled Drawings.doc
21/23
RESULT:
Thus the front and cross section of the given !iveted La& Joint has been drawn and also
assembled using AutoCAD 2000
AIM:
To draw the front and cross section of the given !iveted ,utt Joint and also assemble usingAutoCAD 2000
COMMANDS USED:
Limits oom
Line $ove
Arc '&line
Trim (illetDimlinear Dimradius
PROCEDURE:
%&en the AutoCAD and set the re/uired limit+
(irst draw the 'ingle !iveting b# using commands like Line+ Circle+ etc1
Cross section of the &late is done b# using hatch command+
e*t draw the chain riveting using commands+
"itch of rivet is measured b# using thickness of the &late of line calculation+
Dimension of line is measured b# using dimension command.
-
8/10/2019 Record Assembled Drawings.doc
22/23
-
8/10/2019 Record Assembled Drawings.doc
23/23
RESULT:
Thus the front and cross section of the given !iveted ,utt Joint has been drawn and alsoassembled using AutoCAD 2000