reg-183j reg-253j rads-151j rads-183j rads-253j rad-283j › media › documents › products ›...
TRANSCRIPT
REG-183JREG-253JRADS-151JRADS-183JRADS-253JRAD-283J
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
1
NOTE
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
2
To prevent injury to the user or other people and property damage, the following instructions
must be followed. Incorrect operation due to ignoring of instructions may cause harm or
damage. The seriousness is classified by the following indications.
Safety Precautions
This symbol indicates the possibility of death or serious injury.
Meanings of symbols used in this manual are as shown below.
!
!
WARNING
Always do this.
Never do this.
! CAUTION This symbol indicates the possibility of injury or damage to property.
Plug in power plugproperly.
Do not modify power cordlength or share the outletwith other appliances.
Always ensure effectiveearthing.
Unplug the unit if strangesounds, smell, or smokecomes from it.
Keep firearms away.
Ventilate room before operating airconditioner if there is a gas leakage fromanother appliance.
Otherwise, it may cause electricshock or fire due to heatgeneration.
excess
It may cause electric shock orfire due to heat generation.
Incorrect earthing may causeelectric shock.
It may cause fire and electricshock.
It may cause fire.
It may cause explosion, fire and, burns.
It may cause electric shock or firedue to heat generation.
It may cause electric shock.
It may cause failure of machineor electric shock.
It may cause fire and electricshock.
It may cause fire and electricshock.
It may cause electric shock or fire.If the power cord is damaged, itmust be replaced by the manufac-turer or an authorised servicecentre or a similarly qualified per-son in order to avoid a hazard.
This could damage your health.
Incorrect installation may causefire and electric shock.
It may cause electric shock.
It may cause an explosion or fire.
It may cause failure and electric shock.
Do not operate or stop theunit by inserting or pullingout the power plug.
Do not operate with wethands or in dampenvironment.
Do not allow water to runinto electric parts.
Do not use the socket if it isloose or damaged.
Do not use the power cordclose to heating appliances.
Do not damage or use anunspecified power cord.
Do not direct airflow atroom occupants only.
Always install circuitbreaker and a dedicatedpower circuit.
Do not open the unitduring operation.
Do not use the power cord nearflammable gas or combustibles, suchas gasoline, benzene, thinner, etc.
Do not disassemble or modify unit.
!
!
!
!
!
!
WARNING!
! !!
! Plug in power cord plug properly
! Do not modify power cord length or share the outlet with other appliances.
Always ensure effective grounding
!
Unplug the unit if strange sounds, odors or smoke comes from it.
!
Do not operate or stop the unit by inserting or pulling out the power plug
Do not operate with wet hands or in a damp environment
Do not allow water to run in to electric parts
Do not use the socket if it is loose or damaged! Always install circuit
breaker and a dedicated power circuit
Do not open the unit during operation
Unplug the unit if strange sounds, odors or smoke comes from it.
!
Do not use the power cord close to heating appliances
Do not use the power
or combustiblies, such as gasoline, benzene, thinner, etc.
Do not disassemble or modify unit.
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
3
! CAUTION
When the air filter is to beremoved, do not touch themetal parts of the unit.
It may cause an injury.
Do not clean unit whenpower is on as it may causefire and electric shock, it maycause an injury.
Operation with windowsopened may cause wettingof indoor and soaking ofhousehold furniture.
When the unit is to becleaned, switch off, and turnoff the circuit breaker.
Stop operation and closethe window in storm orhurricane.
Use caution when unpacking andinstalling. Sharp edges could cause injury.
Do not clean the airconditioner with water.
Water may enter the unit anddegrade the insulation. It maycause an electric shock.
This could injure the pet orplant.
It may cause electric shockand damage.
Do not put a pet or houseplant where it will beexposed to direct air flow.
Hold the plug by the headof the power plug whentaking it out.
Ventilate the room well whenused together with a stove,etc.
An oxygen shortage may occur.
Do not use this air conditioner topreserve precision devices, food,pets, plants, and art objects.It may cause deterioration ofquality, etc.
It may cause failure of productor fire.
Do not use for specialpurposes.
Turn off the main powerswitch when not sing theunit for a long time.
u
If water enters the unit, turn the unit off at the poweroutlet and switch off the circuit breaker. Isolatesupply by taking the power-plug out and contact aqualified service technician.
!
!
!
!
! !
!
It may cause failure ofappliance or accident.
Appearance may bedeteriorated due to changeof product color orscratching of its surface.
Do not place obstaclesaround air-inlets or insideof air-outlet.
Do not use strong deter-gent such as wax orthinner but use a soft cloth.
If bracket is damaged, thereis concern of damage due tofalling of unit.
There is danger of fire orelectric shock.
Ensure that the installation bracket ofthe outdoor appliance is not damageddue to prolonged exposure.
Do not place heavy object on thepower cord and ensure that the cordis not compressed.
Operation without filters maycause failure.
It contains contaminants andcould make you sick.
Always insert the filterssecurely. Clean filter onceevery two weeks.
Do not drink water drainedfrom air conditioner.
! !
removed, do not touch the metal parts of the unit
Do not allow water to enter inside the unit during cleaning
Ventilate the room well when used together with a gas stove or if there is a gas leak
When the unit is to be cleaned, switch off, and turn off the circuit breaker
Stop operation and close the window in storm or hurricane
Hold the plug by the head of the power plug when taking it out
Turn off the main power switch when not using the unit for a long time
Do not place obstacles around air-inlets or inside of air-outlet
Ensure that the instal-lation bracket of the outdoor appliance is not damaged
once every two weeks
Do not use strong deter-gents such as wax or thin-ner; use a damp, soft cloth
Do not place heavy ob-ject on the power cord and ensure that the cord is not compressed
Do not drink water drained from air condi-tioner
Use caution when un-packing and installing
If water enters the unit, turn the unit off at the power outlet and switch off the circuit breaker. Isolate supply by taking power-plug out and con-
technician
!
!
! !
!
!
!
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
4
IMPORTANT SAFETY INSTRUCTIONS
Be sure the electrical service is adequate for the model you have
chosen. This information can be found on the serial plate, which
is located on the side of the cabinet and behind the grille.
Be sure the air conditioner is properly grounded. To minimize
shock and fire hazards, proper grounding is important. The power
cord is equipped with a three-prong grounding plug for protection
against shock hazards.
Your air conditioner must be used in a properly grounded wall
receptacle. If the wall receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or circuit breaker,
have a qualified electrician install the proper receptacle.
Ensure the receptacle is accessible after the unit installation.
Do not run air conditioner without side protective cover in place.
This could result in mechanical damage within the air conditioner.
Do not use an extension cord or an adapter plug.
WARNING For your safety
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
Avoid fire hazard or electric shock. Do not use an extension cord or an
adaptor plug. Do not remove any prong from the power cord.
WARNING Electrical Information
NOTE For some models, the power
supply cord with this air conditioner
contains a current detection device
designed to reduce the risk of fire.
Please refer to the section Operation
of Current Device for details.
In the event that the power supply
cord is damaged, it cannot be
repaired-it must be replaced with a
cord from the Product Manufacturer.
,
,
Do not, under anycircumstances, cut,remove, or bypassthe grounding prong.
Power supply cordwith 3-prong grounding plugand current detection device
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
5
Cooling operationOutdoor Temp: 64.4-109.4°F (18-43°C) (T1 Environment) 69.8-125.6°F (21-52°C) (T3 Environment)Indoor Temp: 62.6-89.6°F (17-32°C) (T1 Environment) 62.6-89.6°F (17-32°C) (T3 Environment)
Heat operationOutdoor Temp: 23.0-75.2°F (-5-24°C) (T1 Environment) 19.4-75.2°F (-7-24°C) (T3 Environment)Indoor Temp: 32.0-80.6°F (0-27°C) (T1 Environment) 32.0-86.0°F (0-30°C) (T3 Environment)
Remotesignalreceptor
NOTE
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
6
TO CHANGE TEMPERATURE SETTING:
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
7
To operate in Auto feature:
To operate in Fan only:
To operate in Dry mode:
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
8
AIR CONDITIONER FEATURES (CONTINUED)
TIMER: AUTO START/STOP FEATURE
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
9
THE DISPLAYSAIR CONDITIONER FEATURES (CONTINUED)
3
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
10
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
11
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
12
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
13
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
14
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
15
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
16
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
17
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
18
CARE AND CLEANING
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit
before cleaning to prevent chock or fire hazards.
CAUTION
Air Filter Cleaning
The air filter should be checked at least once a
month to see if cleaning is necessary. Trapped
particles in the filter can build up and cause an
accumulation of frost on the cooling coils.
Push the vent handle to the Vent Closed position
(where applicable).
Open the front panel.
Grasp the filter, pull up and out.
Wash the filter using liquid dishwashing deter-
gent and warm water. Rinse filter thoroughly.
Gently shake excess water from the filter. Be
sure the filter is thoroughly dry before replacing.
Or, instead of washing you may vacuum the
filter clean.
Never use hot water over 40 C(104 F) to
clean the air filter. Never attempt to operate the
unit without the air filter.
Be sure to unplug the air conditioner to prevent
shock or fire hazard. The cabinet and front may
be dusted with an oil-free cloth or washed with
a cloth dampened in a solution of warm water
and mild liquid dishwashing detergent. Rinse
thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the
cabinet front.
Be sure to wring excess water from the cloth before
wiping around the controls. Excess water in or around
the controls may cause damage to the air conditioner.
Plug in air conditioner.
If you plan to store the air conditioner during the winter,
remove it carefully from the window according to the
installation instructions. Cover it with plastic or return it
to the original carton.
Note:
Cabinet Cleaning
Winter Storage
Owner’s Manual Room Air Conditioner with R-410A Heat Controller, Inc.
19
Before calling for service, review this list. It may save you time and expense. This list includes common
occurrences that are not the result of defective workman-ship or materials in this appliance.
Solution
Air conditioner
does not start
Wall plug disconnected. Push plug firmly into wall outlet.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or
reset circuit breaker.
Plug Current Device Tripped. Press the RESET button.
TROUBLESHOOTING TIPS
Problem
Air from unit does
not feel cold
enough
Reset to a Lower temperature.
Room temperature below 17 C(62 F). Cooling may not occur until room temperaturerises above 17 C(62 F).
Thermostat set too cold for night-time cooling. To defrost the coil, set to FAN ONLYmode. Then, set temperature to a Higher setting.
Temperature sensing element touching cold coil, located behind air filter. Straighten
tube away from coil.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost,
set to FAN ONLY mode.
Dirty air filter- air restricted. Clean air filter. Refer to Care and Cleaning section.
Unit recently turned on in hot room. Allow additional time to remove Stored heat from
walls, ceiling, floor and furniture.
Control is OFF. Turn Control ON and set to desired setting.
O O
OO
Air conditioner
cooling, but room
is too warm- ice
forming on cooling
coil behind
decorative front.
Outdoor temperature below 18 C(64 F). To defrost the coil, set FAN ONLY mode.O O
Air conditioner
cooling, but room
is too warm- NO
ice forming on
cooling coil behind
decorative front.
Temperature is set too High, set temperature to a Lower setting.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of units is blocked by drapes, blinds, furniture, etc. - restricts air distribution.
Clear blockage in front of unit.
Doors, windows, registers, etc. Open- cold air escapes. Close doors, windows, registers.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for
compressor to restart when set in the COOL mode.
Air conditioner turns on
and off rapidly
Noise when unit is
cooling
Water dripping
INSIDE when
unit is cooling.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage.
Refer to installation instructions - check with installer.
Dirty air filter- air restricted. Clean air filter.
Air movement sound. This is normal . If too loud, set to a slower FAN setting.
Outside temperature extremely hot. Set FAN speed to a Higher setting to bring air past
cooling coils more frequently.
Window vibration - poor installation. Refer to installation instructions or check with installer.
62°F (17°C).62°F (17°C).
64°F (18°C).
the rear/outside to allow water drainage.
Heat Controller, Inc. Room Air Conditioner with R-410A Owner’s Manual
20
SolutionProblem
Water dripping
OUTSIDE when
unit is cooling.
Unit removing large quantity of moisture from humid room. This is normal during
excessively humid days.
Remote Sensing
Deactivating
Prematurely
(some models)
Remote control not located within range. Place remote control within 20 feet & 180 ,
radius of the front of the unit.
Remote control signal obstructed. Remove obstruction.
Room too cold Set temperature too low. Increase set temperature.
11/2011