renovation of hostel 'e' block of national … · steel work 9.200 19 providing and...

Total Amount(

Rs.)

1 2 3 4 5= (3 x 4 ) 3 + 5

In figures In words In figures In words

1 CIVIL WORKS

As per DSR 2012/Market Rate

(a) EARTH WORK 1568.56

(b) CONCRETE &RCC Work 250373.68

(C) BRICK WORK 65779.94

(d) MARBLE AND GRANITE WORK 46723.64

(e) Joinery Work 1389573.80

(f) Steel Work 2618508.15

(g) Flooring Work 2167060.35

(h) Finishing Work 1163641.86

(i) Demolishing Work 204416.28

(j) Aluminium Work 419053.04

(k) Water proofing Work 1004985.44

(l) Market Rate Items(Flooring) 2156863.56

2 Electrical Work 5467804.84

3 SANITARY & PLUMBING WORKS 2535430.00

4 Fire Fighting Work 281864.0019773647.00 TENDER VALUE

TOTAL TENDER VALUE ( IN WORDS) : Rupees

Seal & Signature of Tenderer

Total

RENOVATION OF HOSTEL 'E' BLOCK OF NATIONAL INSTITUTE OF TECHNOLOGY, CAMPUS, RAIPUR

PRICE SCHEDULE

SI. No. DESCRIPTION

ESTIMATED

COST (Rs.)

TO BE QUOTED BY TENDERER

% ( - ) Below / At ParAmount ( - ) Below / At Par

Estimated Cost

DSR No. Sl.No. Description Unit Qty. Rate DSR Amount NDSR Amount

(1) (2) (3) (4) (5) (6) (7) (8)

EARTH WORK

1.1.1 1 Carriage of material by mechanical Transport

including loading ,unloading and stacking of Lime,

moorum, building rubbish up to 5 km Cum 5.60 122.46 686.12

2.800 2 Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in foundation

trenches or drains (not exceeding 1.5 m in width or

10 sqm on plan) including dressing of sides and

ramming of bottoms, lift upto 1.5 m, including getting

out the excavated soil and disposal of surplus

excavated soil as directed, within a lead of 50 m. cum 5.60 157.50 882.44

2.8.1 All kinds of soil

1568.56

CONCRETE WORK

4.170 3 Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement :3 coarse sand : 6graded

stone aggregate 20mm nominal size) over 75mm bed

by dry brick ballast 40mm nominal size well rammed

and consolidated and grouted with fine sand

including finishing the top smooth sqm 157.50 419.30 66039.75

REINFORCED CEMENT CONCRETE

FORM WORK

5.900 4 Centering and shuttering including strutting, propping

etc. and removal of form for :

5.9.3 b Suspended floors, roofs, landings, balconies and

access platform. sqm 11.34 40.65 460.97

BILL OF QUANTITY (BLOCK E) FOR NIT RAIPUR

CIVIL WORKS

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

5.9.5 c Lintels, beams, plinth beams, girders, bressumers and

cantilevers. sqm 303.80 332.15 100907.17

STEEL REINFORCEMENT

5.220 5 Reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

and binding all complete. kg 642.92 68.10 43782.51

5.22.6 Thermo-Mechanically Treated bars.

DESIGN MIX CONCRETE

5.330 6 Providing and laying in position machine batched and

machine mixed design mix M-25 grade cement

concrete for reinforced cement concrete work, using

cement content as per approved design mix, including

pumping of concrete to site of laying but excluding

the cost of centering, shuttering, finishing and

reinforcement, including admixtures in recommended

proportions as per IS: 9103 to accelerate, retard

setting of concrete, improve workability without

impairing strength and durability as per direction of

Engineer-in-charge.

(Note :- Cement content considered in this item is @

330 kg/cum Excess/less cement used as per design

mix is payable/recoverable separately).5.33.2 a All works above plinth level upto floor V level cum 5.59 7014.55 39183.28

250373.68HALF BRICK MASONRY

6.130 7 Half brick masonry with F.P.S. bricks of class

designation 7.5 in superstructure above plinth level

up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement : 4 coarse sand) sqm 89.46 665.80 59562.47

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

6.150 8 Extra for providing and placing in position 2 Nos.

6mm dia. M.S. bars at every third course of half brick

masonry (with F.P.S. bricks). sqm 89.46 69.50 6217.47

65779.94Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

MARBLE & GRANITE WORK

8.200 9 Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters,

window sills , facias and similar locations of required

size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4

coarse sand), joints treated with white cement, mixed

with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to

give high gloss finish etc. complete at all levels.8.2.2 Granite of any colour and shade

8.2.2.2 a Area of slab over 0.50 sqm sqm 11.34 3907.40 44309.92

8.600 10 Mirror polishing on marble work/Granite work/stone

work where ever required to give high gloss finish

complete. sqm 11.34 212.85 2413.72

46723.64ANODISED ALUMINIUM FITTINGS (ALL

FITTINGS SHALL BE ISI MARKED)9.830 11 Providing and fixing IS : 3564 marked Aluminium

die cast body tubular type universal hydraulic door

closer with necessary accessories and screws etc. Each 48.00 753.75 36180.00

9.960 12 Providing and fixing aluminium sliding door bolts ISI

marked anodised (anodic coating not less than grade

AC 10 as per IS : 1868) transparent or dyed to

required colour or shade with nuts and screws etc. Each 96.00 229.65 22046.00

9.96.1 300x16 mm

9.100 13 Providing and fixing aluminium handles ISI marked

anodised (anodic coating not less than grade AC 10

as per IS : 1868) transparent or dyed to required

colour or shade with necessary screws etc. complete :

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

9.100.1 a 125 mm each 120.00 69.80 8376.00

9.100.2 b 100 mm each 96.00 55.10 5289.60

9.101 14 Providing and fixing aluminium hanging floor door

stopper ISI marked anodised (anodic coating not less

than grade AC 10 as per IS : 1868) transparent or

dyed to required colour and shade with necessary

screws etc. complete.

9.101.2 Twin rubber stopper each 48.00 83.95 4029.60

9.103 15 Providing and fixing bright finished brass 100 mm

mortice latch and lock ISI marked with six levers and

a pair of anodised (anodic coating not less than grade

AC 10 as per IS : 1868) aluminium lever handles

with necessary screws etc. complete (Best make of

approved quality). each 48.00 815.45 39141.60

9.108 16 Providing and fixing PTMT Tower Bolts with 12 mm

one piece rod inside and necessary screws etc.,

complete.

9.108.1 a 152x42x18 mm weighing not less than 60 gms each 150.00 88.50 13275.00

9.108.2 b 202x42x18 mm weighing not less than 78 gms each 120.00 113.65 13638.00


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

9.119 17 Providing and fixing factory made P.V.C. door frame

of size 50x47 mm with a wall thickness of 5 mm,

made out of extruded 5mm rigid PVC

foam sheet, mitred at corners and joined with 2 Nos

of 150 mm long brackets of 15x15 mm M.S. square

tube, the vertical door frame profiles to be reinforced

with 19x19 mm M.S. square tube of 19 gauge, EPDM

rubber gasket weather seal to be provided through out

the frame. The door frame to be fixed to the wall

using M.S. screws of 65/100 mm size, complete as

per manufacturer’s specification and direction of

Engineerin-Charge. m 396.00 458.95 181744.20

9.124 18 Providing and fixing factory made 30 mm thick door

shutter made of solid PVC foam profile. The styles &

rails shall be of size 75 mm x 30 mm having wall

thickness 5 mm. The styles, top & bottom rails shall

have one side wall thickness of 15 mm integrally

extruded on the hinge side of the profile for better

screw holding power. The styles and rails shall be

reinforced with M.S. tubes of size 33 mm x 17 mmx

1 mm, painted with primer , all four corners of

reinforcement to be welded or sealed. Solid PVC

extruded bidding (push fit type) will be set inside the

styles and the rails with a cavity, to receive single

piece extruded 5 mm PVC sheet as panel. The styles

and rails will be mitred cut and joint with the help of

PVC solvent cement & self driven self tapping

screws. Single piece extruded solid PVC lock rail of

size 100 mm x 30 mm with wall thickness 5 mm &

15 mm integrally extruded in the middle of the lock

rail & fixed with styles with the help of PVC solvent

cement & self driven self tapping screws of size 100

mm x 8 mm complete as per manufacturer's


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

9.124.1 a Non decorative finish sqm 396.00 2691.55 1065853.80

#########STEEL WORK

9.200 19

Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) decorative type, core

of block board construction with frame of 1st class

hard wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face veneers

on both faces of shutters.

9.20.135 mm thick including ISI marked Stainless Steel butt

hinges with necessary screws sqm 159.12 2,606.45 414738.32

9.480 20

Providing and fixing M.S. grills of required pattern in

frames of windows etc. with M.S. flats, square or

round bars etc. including priming coat with approved

steel primer all complete.

9.48.2Fixed to openings /wooden frames with rawl plugs

screws etc. kg 5562.42 116.90 650246.41

10.140 21 Providing and fixing pressed steel door frames

conforming to IS: 4351, manufactured from

commercial mild steel sheet of 1.60 mm thickness,

including hinges, jamb, lock jamb, bead and if

required angle threshold of mild steel angle of

section 50x25 mm, or base ties of 1.60 mm, pressed

mild steel welded or rigidly fixed together by

mechanical means, including M.S. pressed butt

hinges 2.5 mm thick with mortar guards, lock strike

plate and shock absorbers as specified and applying

a coat of approved steel primer after pre-treatment

of the surface as directed by Engineerin-charge:10.14.2 Profile C10.14.2.1 Fixing with carbon steel galvanised dash fastener of

required dia and size (to be paid for separately) m 2361.60 400.95 946883.52

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

10.110 22 Providing and fixing factory made ISI marked steel

glazed doors, windows and ventilators, side /top

/centre hung, with beading and all members such as

F7D, F4B, K11 B and K12 B etc. complete of

standard rolled steel sections, joints mitred and flash

butt welded and sash bars tenoned and riveted,

including providing and fixing of hinges, pivots,

including priming coat of approved steel primer, but

excluding the cost of other fittings, complete all as

per approved design, (sectional weight of only

steel members shall be measured for payment).

10.11.1 Fixing with 15x3 mm lugs 10 cm long embedded in

cement

concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement

: 3 coarse sand : 6 graded stone aggregate 20 mm

nominal size) kg 5314.41 114.15 606639.90

######### FLOORING

11.260 22 Kota stone slab flooring over 20 mm (average) thick

base laid over and jointed with grey cement slurry

mixed with pigment to match the shade of the slab,

including rubbing and polishing complete with base

of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

11.26.1 25 mm thick sqm 1760.26 1141.40 2009159.62

11.310 23 Extra for pre finished nosing in treads of steps of

Kota stone/ sand stone slab. Rm 75.60 75.80 5730.48

11.320 24 Extra for Kota stone/ sand stone in treads of steps and

risers using single length up to 1.05 metre . sqm 35.05 16.90 592.28

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

8.02 11.2 Providing and fixing 10 mm thick acid and/or alkali

resistant tiles of approved make and colour using acid

and/or alkali resisting mortar bedding, and joints filled

with acid and/or alkali resisting cement as per

IS : 4457, complete as per the direction of Engineer-

in- Charge.11.21.2.1 Acid and alkali resistant tile R/o Sqm 1259.85


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

CERAMIC GLAZED TILES

11.360 25 Providing and fixing Ist quality ceramic glazed wall

tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in

all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge,

in skirting, risers of steps and dados, over 12 mm

thick bed of cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed

with pigment of matching shade complete. sqm 67.62 836.65 56574.27

12.100 26 Providing corrugated G.S. sheet roofing including

vertical / curved surface fixed with polymer coated J

or L hooks, bolts and nuts 8mm diameter with

bitumen and G.I. limpet washers or with G.I. limpet

washers filled with white lead, including a coat of

approved steel primer and two coats of approved

paint on overlapping of sheets complete (up to any

pitch in horizontal/ vertical or curved surfaces),

excluding the cost of purlins, rafters and trusses and

including cutting to size and shape wherever 12.1.3 0.63 mm thick with zinc coating not less than 275

gm/ m² sqm 84.55 743.45 62858.70

12.400 Providing ridges or hips of width 60 cm overall width

plain G.S. sheet fixed with polymer coated J. or L

hooks, bolts and nuts 8 mm dia G.I. limpet and

bitumen washers complete.

12.4.2 0.63 mm thick with zinc coating not less than 275

gm/m² M 30.00 502.75 15082.50


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

12.110 Extra for providing and fixing wind ties of 40x 6 mm

flat iron section. M 150.00 113.75 17062.50

#########FINISHING

CEMENT PLASTER (IN FINE SAND)

13.100 27 12 mm cement plaster of mix :

13.1.1 1:4 (1 cement : 4 fine sand) sqm 174.34 163.35 28478.77

13.200 28 15 mm cement plaster on the rough side of single or

half brick wall of mix :

13.2.2 1:6 (1 cement: 6 fine sand) sqm 174.34 172.80 30126.31

13.480 29

finishing with deluxe multi surface paint syestem for

imteriors and exterier using primer as manufacturur

specification;

13.48.2

painting wood work with deluxe multi surface paint

of required shade.two or more coat

[email protected]/10 sqm over an under coat of primer

[email protected]/10 ltr sqm of approved brand and sqm 454.37 88.2 40074.99

13.520 30

Finishing with Epoxy paint (two or more coats) at all

locations prepared and applied as per manufacturer's

specifications including appropriate priming coat,

preparation of surface, etc. complete.

13.52.1 On steel work sqm 454.37 116.55 52956.24

INTERIOR FINISHING

13.410 31 Distempering with oil bound washable distemper of

approved brand and manufacture to give an even

shade :

13.41.1 New work two coats over and including priming coat

with cement primer. sqm 3749.87 89.70 336363.68

EXTERIOR FINISHING

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

13.800 32 Providing and applying white cement based putty of

average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to

prepare the surface even and smooth complete. sqm 5359.84 89.65 480509.50

13.470 33 Finishing walls with Premium Acrylic Smooth

exterior paint with Silicone additives of required sqm 1609.96 94.95 152866.12

13.47.1 New work (Two or more coats applied @ 1.43 ltr/ 10

sqm over and including priming coat of exterior

primer

13.620 34 Painting with synthetic enamel paint of approved

brand and

manufacture of required colour to give an even shade

13.62.1 Two or more coats on new work over an under coat

of

suitable shade with ordinary paint of approved brand

and sqm 397.80 106.25 42266.25

#########DEMOLISHED ITEM

15.700 35 Demolishing brick work manually/ by mechanical

means including stacking of serviceable material and

disposal of unserviceable material within 50 metres

lead as per direction of Engineer-in-charge.

15.7.4 In cement mortar Cum 5.60 754.10 4225.07

15.120 36 Dismantling doors, windows and clerestory windows

(steel or wood) shutter including chowkhats,

architrave, holdfasts etc. complete and stacking

within 50 metres lead :

15.12.1 a Of area 3 sq. metres and below each 107.54 141.25 15189.32

15.12.2 b Of area beyond 3 sq. metres each 15.30 193.85 2965.91

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

15.230 37 Dismantling tile work in floors and roofs laid in

cement mortar including stacking material within 50

metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm sqm Sq.m 567.79 28.20 16011.55

15.260 38 Demolishing brick tile covering in terracing including

stacking of serviceable material and disposal of

unserviceable material within50 metres lead. Sq.m 464.06 40.80 18933.62

15.270 39 Demolishing mud phaska in terracing and disposal of

material within 50 metres lead. Cu.m 46.41 334.60 15527.42

15.420 40 Dismantling C.I. or asbestos rain water pipe with

fittings and clamps including stacking the material

within 50 metres lead :

15.42.2 a 100 mm dia pipe RM 240.00 28.60 6864.00

15.560 41 Dismantling old plaster or skirting raking out joints

and cleaning the surface for plaster including disposal

of rubbish to the dumpingground within 50 metres Sq.m 1463.60 20.05 29345.26

14.430 42 Removing white or colour wash by scrapping and

sand papering and preparing the surface smooth

including necessary repairs to scratches etc. complete Sq.m 3408.98 7.60 25908.22

16.680 43 Providing and laying 60mm thick factory made

cement concrete interlocking paver block of M -30

grade made by block making machine with strong

vibratory compaction, of approved size, design &

shape, laid in required colour and pattern over and

including 50mm thick compacted bed of coarse sand,

filling the joints with fine sand etc. all complete as

per the direction of Engineer-in-charge. sqm 115.32 602.20 69445.91

204416.28Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

ALUMINIUM WORK

21.300 44 Providing and fixing glazing in door, window,

ventilator shutters and partitions etc. with EPDM

rubber / neoprene gasket etc. complete as per the

architectural drawings and the directions of engineer- sqm 307.85 1054.20 324530.20

21.3.2 With float glass panes of 5.50 mm thickness

21.100 45 Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z

sections and other sections of approved make

conforming to IS: 733 and IS : 1285, fixed with rawl

plugs and screws or with fixing clips, or with

expansion hold fasteners including necessary filling

up of gaps at junctions, at top, bottom and sides with

required EPDM rubber/neoprene gasket etc.

Aluminium sections shall be smooth, rust free,

straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap

beading for glazing / paneling, C.P. brass / stainless

steel screws, all complete as per architectural

drawings and the directions of Engineer-in-charge. 21.1.1 a For fixed portion

21.1.1.3 Polyester powder coated aluminium (minimum

thickness of polyester powder coating 50 micron) kg 55.13 385.10 21228.64

21.1.2 b For Openable portion

21.1.2.3 Polyester powder coated aluminium (minimum

thickness of polyester powder coating 50 micron) kg 165.38 443.20 73294.20

419053.04WATER PROOFING

Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

22.500 45 Providing and laying water proofing treatment in

sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement

compound consisting of applying : a) First layer of

slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/sqm. This

layer will be allowed to air cure for 4 hours. b)

Second layer of slurry of cement @ 0.242 kg/sqm

mixed with water proofing cement compound @

0.126 kg/sqm. This layer will be allowed to air cure

for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment

and sealing of all joints, corners, junctions of pipes

and masonry with polymer mixed slurry. sqm 114.68 283.10 32465.91

MR 46 (a)Plastering and repairing the surface .After

removing the kota stone and bedding mortar the

surface is to be plastered with KEM PROOF/Sika

Top 77/POWERCRETE or equivalent (Acrylic

emulsion and water proof addictive with having a

density 1.03 kg/ltr at 27deg C and solid content 40%)

modified cement moratr.It will be applied with

aproportion of 1:4 by volume of additive to water.


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

(b)Waterproofing Treatment :

Surface preparation: Cleaning all loose particles like

cement, sand, and substrate making than even surface

free from dust, dirt, grease using the steel/nylon wire

brush for cleaning.

Surface to be treated should be sound, clean and free

from dirt oil and other loose material. Washing the

surface with adequate water ensuring complete

cleaning.

Treatment :

Providing and applying two coats of elastomeric,

single component Polyurethane based, liquid applied

waterproof coating membrane system with fiber glass

mesh after application of priming material as per

manufacturer’s specification on the prepared

substrate. There should be minimum interval of 4-6

Hrs after between priming the surface and

waterproof PU based membrane coating. Interval

between two coats of PU based coating membrane

should be minimum 12 Hrs.

Immediately after the 2nd and final coat on the

surface spray of fine washed sand to be done @6

CUDM/Sqm

Details of PU based coating :

Standard Compliance : ASTM D412, E96-05, ASTM

G154, ASTM836-05, ASTM 836-84M, BS 476: Part

III, ISO 1523,1983 /ASTM 836-89, / ASTM 836-84,

(c) After the above coating laying of average 50mm

thick PCC over the coating and finishing smooth and

mixing of rich polymer of 40% @1kg per bag of

cement (Polymer solid contents as per ASTM

C1059),ensuring that screed gently slopes towards the sqm 641.42 1250.00 801779.34


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

9.510 51 Providing and fixing fly proof galvanized M.S. wire

gauge to windows and clerestory windows using wire

gauge with average width of aperture 1.4 mm in both

directions with wire of dia 0.63 mm all complete.

9.51.2 With 12 mm mild steel U beading sqm 295.25 578.30 170740.18

32465.91 972519.53Total


(1) (2) (3) (4) (5) (6) (7) (8)


CIVIL WORKS

MARKET RATE ITEMS

M.R 52 Providing and laying light cinder filling under floors

of toilets and kitchen and other sunken roofs rammed

and compacted complete. cum 36.54 579.00 21156.66

M.R 53 Providing & laying, polished 18mm to 20mm thick

Granite flooring with water absoption,s less than

0.08% and conforming to IS : 15622 of approved

make in all colours and shade , laid on 20 mm thick

cement mortar 1:4 ( 1 cement : 4 coarse sand )

including grouting the joint with white cement and sqm 500.17 4270.00 2135706.90

#########TOTAL COST OF CIVIL

TOTAL

S.No SUB HEAD DISCRIPTIOND.S.R. ITEM N.S. ITEM

I POINT WIRING (Copper Wiring in Pvc

Conduits)

1117263.00 0.00

II ERECTION OF LIGHTING FIXTURES

AND FANS

116218.00 9690.00

III TELEPHONE, TELEVISION AND

DATA NETWORK16084.00 0.00

IV SUPPLY OF LIGHTING FIXTURES AND

FANS

0.00 1017357.91

V DISTRIBUTION BOARDS, MCB'S AND

POWER DISTRIBUTION SYSTEM

64972.00 955100.93

VI External Lighting 102336.00 644643.00VII CABLE AND ITS LAYING 233358.00 857650.00VIII EARTHING 151706.00 0.00IX LIGHTNING CONDUCTORS 81701.00 0.00X MISCELLANEOUS 266.00 99459.00

SUB TOTAL 1883904.00 3583900.84

TOTAL 5,467,804.84

PROJECT NAME : NIT Hostel AtRaipur

NAME OF WORK: Internal Wiring, Distribution Board/ MCB, Supply of Lighting SUMMARY OF COST

AMOUNT (Rs.)

S. No. CODE DESCRIPTION QTY. UNIT RATE

D.S.R. ITEM N.S. ITEM

SUB HEAD (I):- POINT WIRING (Copper Wiring in

PVC Conduits)1.1 1.10 Wiring for light point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed

medium class pvc conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc 1.1.a 1.10.3 Group C 287 Point 718.00 206066.00

1.2 1.10 Wiring for fan point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed

medium class pvc conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc 1.2.a 1.10.3 Group C 123 Point 718.00 88314.00

1.3 1.10 Wiring for exhaust fan point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class pvc conduit, with modular switch,

modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core 1.3.a 1.10.3 Group C 25 Point 718.00 17950.00

1.4 1.10 Wiring for call bell point with 1.5 sq.mm FRLS PVC


recessed medium class pvc conduit, with modular switch,

modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core 1,4,a 1.10.3 Group C 0 Point 718.00 0.00

1.5 1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC


recessed PVC conduit, 2 way modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm. FRLS

PVC insulated copper conductor single core cable etc as

24 Point 770.00 18480.00

1.6 1.14 Wiring for circuit/ submain wiring alongwith earth wire with

the following sizes of FRLS PVC insulated copper conductor,

single core cable in surface/ recessed medium class PVC

conduit as required1.6.a 1.14.1 2X1.5 Sqmm+1X1.5 sqmm earth wire 200 Meter 106.00 21200

1.6.b 1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2355 Metre 131.00 308505.00

1.6.c 1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 240 Metre 162.00 38880.00

1.6.d 1.14.10 4 X 10 sq. mm + 2 X 10 sq. mm earth wire 250 Metre 597.00 149250.00

1.6.e 1.14.11 4 X 16 sq. mm + 2 X 16 sq. mm earth wire 240 Metre 883.00 211920.00

1.6.f 1.14.4 2X6 6Sqmm+1X6 Sqmm earth Wire 240 Meter 221.00 53040.00

ESTIMATE FOR NIT HOSTEL Raipur(C.G)

AMOUNT (RS.)


PVC Conduits)1.6.g NA Additional payment Usind Recommended Company FRLS ISI

Single Core Multi Stranded wire in place of ISI wire in

CPWD Point & Circuit Wiring Items

As Per Site Meter 10% of Related

Items Rate

TOTAL SUB HEAD (I) 1,113,605.00

SUB HEAD (II):- ERECTION OF LIGHTING

FIXTURES AND FANS2.1 1.41 Installation, testing and commissioning of pre-wired,

fluorescent fitting / compact fluorescent fitting of all types,

complete with all accessories and tube etc. directly on ceiling/

wall, including connection with 1.5 sq. mm FRLS PVC

insulated, copper conductor, single core cable and earthing

149 Each 91.00 13559.00

2.2 1.45 Installation, testing and commissioning of ceiling fan,

including wiring the down rods of standard length (upto 30

cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor,

single core cable, including providing and fixing phenolic

laminated sheet cover on the fan box etc. as required.

123 Each 122.00 15006.00

2.3 1.46 Installation, testing and commissioning of resistance type

ceiling fan regulator, in existing switch box including

connection with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable, earthing the regulator etc. as

123 Each 52.00 6396.00

2.4 The fixing and testing of lighting fixture shall include

connection with 3 x 1.5 sqmm flexible fire retardant copper

connecting wire of required length complete with all

accessories, control gears, transformer, including screws, nuts,

wooden cleats, making hole in wall or ceiling and making 2.4.a NA Down lighter luminaire of all types with all accessories

directly on recess

126 Each 75.00 9450

2.4.b NA Mirror type light fittings of all types with all accessories

directly on recess

12 Each 20.00 240

NA Wall Bracket CFL 0 Each 20.00 0

2.5 1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing

junction box/ wooden block including connection etc as

required.

123 Each 43.00 5289.00

2.6 1.50 Installation of exhaust fan in the existing opening, including

making good the damage, connection, testing, commissioning

etc. as required.2.6.a 1.50.1 Upto 450 mm sweep 25 Each 204.00 5100.00

2.7 1.51 Extra for fixing the louvers/ shutters complete with frame for

a exhaust fan of all sizes.

25 Each 90.00 2250.00


PVC Conduits)2.8 1.31 Supplying and fixing suitable size GI box with modular plate

and cover in front on surface or in recess, including providing

and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps

modular switch, connection etc. as required. (For light plugs

to be used in non residential buildings).

181 Each 303.00 54843.00

2.9 1.32 Supplying and fixing suitable size GI box with modular plate

and cover in front on surface or in recess, including providing

and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and

15/16 amps modular switch, connection etc. as required.

12 Each 395.00 4740.00

2.1 2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type,

socket outlet, with 2 pole and earth, metal enclosed plug top

alongwith 20 amps "C" curve, SP, MCB, in sheet steel

enclosure, on surface or in recess, with chained metal cover

for the socket out let and complete with connections, testing

and commissioning etc. as required.

12 Each 954.00 11448.00

TOTAL SUB HEAD (II) 118631.00 9690.00

SUB HEAD (III):- TELEPHONE, TELEVISION AND

DATA NETWORK3.1 1.21 Supplying and fixing of following sizes of PVC conduit along

with the accessories in surface / recess including cutting the

wall and making good the same in case of recessed conduit as

required: (For Telephone / T.V. Cable/Data Network). 3.1.a 1.21.1 20mm 100 Meter 53 5300

3.1.b 1.21.2 25mm 100 Meter 65 6500

3.2 1.24 Supplying and fixing following modular switch/ socket on the

existing modular plate & switch box including connections

but excluding modular plate etc. as required.3.2.a 1.24.6 Telephone socket outlet 0 Each 95.00 0.00

3.2.b 1.24.7 TV antenna socket outlet 3 Each 94.00 282.00

3.3 1.27 Supplying and fixing following size/ modules, GI box

alongwith modular base & cover plate for modular switches in

recess etc as required.3.3.a 1.27.1 1 or 2 Module (75mmX75mm) 3 Each 166.00 498.00

3.4 1.18 Supplying & drawing telephone wire following pair, 0.5 sq

mm FRLS PVC insulated annealed copper conductor,

unarmoured telephone cable in the existing surface / recessed

PVC conduit as required.3.4.a 1.18.2 2 Pair 0 Meter 18 0.00

3.4.b N.A 10 Pair 0 Meter 68.00 0

3.5 1.19 Supplying & drawing co-axial TV cable RG-6 grade, 0.7 mm

solid copper conductor PE insulated, shielded with fine tinned

copper braid and protected with PVC sheath in the existing

surface / recessed conduit as required.

75 Meter 28 2100.00


PVC Conduits)3.6 Providing, fixing, connecting & testing of Krone box

(Telephone Tag Block) in a thermoplastic, IP 65 (weather

proof) enclosure, internally embedded gasket, anti corrosive,

insulated and shock proof with provision for cable through IP

65 glands complete in all respects. 3.6.a N.A 10 pairkrone 0 Each 844.00 0

3.7 N.A Supply & installation of Cat 6 information outlet complying

fully or exceeding with category 6 connecting hardware

specification for all pair combination upto 250 MHz. Outlets

shall use lead frame technology, non PCB pyramid type. (Blue

in colour for data).

0 Each 330.00 0.00

3.8 N.A Supply & Installation of single port face plates along with

clearly printed lables and holders.

0 Each 192.00 0.00

3.9 Providing, drawing, connecting and testing of enhanced

category 4 pair LAN (local area network) cable, UL and CUL

listed, in existing MS/PVC conduit or floor raceways

including connections etc as required complete in all respects. 3.9.a N.A CAT- 6 network cable 0 Meter 78.00 0.00

3.11 1.38 Supplying and fixing call bell/ buzzer suitable for single

phase,230 volts, complete as required.

0 Each 61.00 0.00

TOTAL SUB HEAD (III) 14,680.00 0.00

SUB HEAD (IV):- SUPPLY OF LIGHTING FIXTURES

AND FANS(The sample of all lighting fixtures & fans should be approved

by Engineer In charge or Architect before procurement)4.1 Supply of Recess mounted 600 X600 mm Module 2

X36 watt Compact CFL type Mirror optic Fitting with

required CFL lamps, control gear box etc. complete in all

respect as required as per the standard catalogue item.

Make: philps or equivalent4.1.a N.A. FBS 300 2XPL-L36 W P EBT 44 Nos 6954.00 305,976.00

4.2 Supply of Wall mounted Deco Battons T-5 type Fitting with

T-5 lamps, control gear box etc. complete in all respect as

required as per the standard catalogue item. Make: Phillips or

equivalent(TCS019 1xTL-D 36W EBT)4.2.a N.A. 1 x 36W T-5 surface mounted 105 Nos 749.00 78,645.00

4.3 Supply of recess mounted CFL type ceiling light fixtures

down lighter with required nos. lamps etc. complete in all

respect as required as per the standard catalogue item.4,3,b N.A. 18W 126 Nos 1605.00 202,230.00


PVC Conduits)N.A. Supply of 14 Watt Wall Bracket CFL 0 Nos 227.00

4.4 Supply of wall mounted Mirror type light fixtures with

required nos. lamps etc. complete in all respect as required as

per the standard catalogue item.4.4.a N.A. 2x13W 12 Nos 1109.66 13,315.91

4.5 Supply of AC 230/250 volts, 50Hz ceiling fan with standard

down rod, blades, 2 nos caps etc. complete. Make: Havells or

equivalent4.5.a N.A. 1200 mm sweep 123 Nos 2942.00 361,866.00

4.6 Supply of AC 230/250 volts, 50Hz exhaust fans including

providing nuts, bolts, mounting frame and other accessories

etc. complete (Havells make or equivalent)4,6,a N.A. 250 mm sweep 25 Nos 2213.00 55,325.00

TOTAL SUB HEAD (IV) 0.00 1,017,357.91

SUB HEAD (V):- DISTRIBUTION BOARDS, MCB'S

AND POWER DISTRIBUTION SYSTEM

5.1 N.A Design, manufacture, supply, installation, testing and

commissioning of main distribution board fabricated out of 14

SWG sheet steel, wall / floor mounting type, with seven tank

treatment process followed by powder coat painting having a

paint thickness of 60 microns., 415 V electrolitic Al. Bus bar

having short circuit current is 50kA and, removable gland

plates as per SLD . including connection with outgoing

feeders complete in all respect. panels will be provided with

suitable gasket to make it dust/vermin proof. IP 54 protectionThe above board shall be complete with 3 nos. phase

indicating lights, flush mounted Ammeter, Voltmeter, CT's,

PT's selector switches, protective fuses etc. at Incomer with all

inter connetions by min. 2.5 sq mm Copper wires.Main panel 1 SET 504791.90 504791.90

INCOMER:

400 Amp FP MCCB 36 KA

250 Amp FP MCCB 36 KA

BUS BAR: 600 AMP TPN AL.

Automatic Change Over : 600 A Manual Change Over

OUTGOINGS:

100A FP MCCB 36kA 4 nos

63A FP MCCB 36kA 1 nos

63A TP MCB 36kA 2 nos


PVC Conduits)40A TP MCB 36kA 4nos

5.3 N.A Supply, installation, testing and commissioning of weather

and vermin proof outdoor type External Lighting feeder pillar

(IP-65) fabricated from 14 SWG thick CRCA sheet steel

construction suitable for 3 phase, 4 wire, 415 volt, 50 Hz A.C.

distribution complete with Al. bus bars, switch fuse unit,

timer, contactor, fitting with fuse link, locking arrangement

complete as per specification required.INCOMER:-

1 No. 100 Amp. TPN MCCB with neutral link.

1 set of time switch contactor push button changeover switch

etc. complete as per drawing suitable for automatic operation

of external lighting.BUS BAR : 200AMP TPN Al.

OUTGOING :-

1 No. 63 Amp. TPN MCB with neutral link.

5 No. 32 Amp. TPN MCB with neutral link.

20 mm x 3mm GI earth busbar to be fixed inside the pillar and

for connection outside earth strip on both sides of pillar

1 Set 109080 109080

5.4 NA Supply Installation Testing & Commissioning of Out door

Type weather and insect proof pole mounted distribution

junction box Made out of 14 SWG CRCA Sheet steel

construction with approved Colour paintrd having following

incomer and out going

1 Nos Incomer MCB Isolator 32 Amp

1 Nos Outgoing Singal pole MCB 10 Amp

Internaly cnnected with 16 Sqmm Flexible PVC Insulatrd FR

Copper conductor.

30 SEt 8211 246340

5.4 2.5 Supplying and fixing of following ways surface/ recess

mounting, vertical type, 415 volts, TPN MCB distribution

board of sheet steel, dust protected, duly powder painted,

inclusive of 200 amps tinned copper bus bar, common neutral

link, earth bar, din bar for mounting MCB's (but without

MCB's and incomer ) as required . (Note : Vertical type MCB

TPDB is normally used where 3 phase outlets are required.)5,4,a 2.5.4 4 way (4 + 12), Double door 2 Each 4478 8956.00

2.5.5 8 Way(4+24) Double Door 1 5641 5641.00


PVC Conduits)5.5 2.4 Supplying and fixing following way, horizontal type three

pole and neutral, sheet steel, MCB distribution board, 415

volts, on surface/ recess, complete with tinned copper bus bar,

neutral busbar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But without

MCB/ RCCB/5,5,b 2.4.5 6 way (4 + 18), Double door 1 Each 2636 2636.00

5,5,c 2,4,4 4 way (4 + 12), Double door 2 Each 2175 4350.00

2.4.6 8 Way(4+24) Double Door 9 Each 3148 28332

5.6 N.A Supplying and fixing following rating, four pole, 415 volts,

MCCB in the existing MCB DB complete with connections,

testing and commissioning etc. as required.5,6,a N.A 100 amps FP MCCB 3 Each 11189.00 33567.00

5,6,c N.A 63 amp FP MCB 24 Each 2190.07 52561.77

5,6,d N.A 40 amp FP MCB 4 Each 2190.07 8760.30

5.7 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,

"C" curve, miniature circuit breaker suitable for inductive load

of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.5,7,a 2.10.1 Single pole 136 Each 169 22984.00

5.8 2.11 Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

25 Each 7 175.00

TOTAL SUB HEAD (V) 73074.00 955100.93

SUB HEAD (VI):- EXTERNAL LIGHTING

6.1 N.A Supply of pole mounted Street Light for external lighting

suitable for CDMT lamps complete with required nos. lamps

and control gear etc. complete as required as per the standard

catalogue item.6.1.a N.A BGWRL 150 SV FFG (MH T 150W) 7 Each 9528.00 66696

6.2 N.A Supply of pole mounted post top lantern for external lighting

suitable for CDMT lamps complete with required nos. lamps

and control gear etc. complete as required as per the standard

catalogue item.6,2,a N.A SPC101 1xSON70W E 19 Each 6161.00 117059

6.3 N.A Supply of bollard garden light suitable for CFL lamps

complete with required nos. lamps, control gear etc. complete

as required as per the standard catalogue item.6,3,a N.A HCS 360 1xPLC/2P18W GR 20 Each 7241.00 144820


PVC Conduits)6.4 N.A Installation, testing and commissioning of Street Light with

required lamps complete with control gear box, ballast,

capacitor etc. including connection with 3 x 1.5 sq.mm

flexible fire retardant copper connecting wire of required

7 Each 400 2800

6.5 N.A Installation, testing and commissioning of CDMT type post

top lantern with required lamps complete with control gear

box, ballast, capacitor etc. including connection with 3 x 1.5

sq.mm flexible fire retardant copper connecting wire of

required length complete as required.

19 Each 400 7600

6.6 N.A Installation, testing and commissioning of CFL type bollard

garden light fixtures with required lamps, control gear box,

including connection with 3 x 1.5 sq.mm flexible fire

retardant copper connecting wire of required length complete

20 Each 300 6000

6.7 N.A Supply and fixing of steel tubular pole 7.50 m long of

designation 410 SP-6 fixed in 1:3:6 cement concrete

foundation, including excavation, back filling etc. complete in

7 Each 6000.00 42000

6.8 NA Supply and fixing of GI Octagonal GI 11 Mtr hight Pole

Complete with all acessories like base plate foundation

acessories top canopy for high mast light mounting etc.fixed

in 1:3:6 cement concrete foundation, including excavation,

back filling etc. complete in all respects.

2 Each 21900.00 43800

6.9 N.A Supply and fixing of steel tubular pole 4.50 m long of

designation 410 SP-6 fixed in 1:3:6 cement concrete

foundation, including excavation, back filling etc. complete in

19 Each 5764.00 109516

7 11.4 Erection of steel tubular or rail pole strut in cement concrete

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40

mm nominal size ) foundation including excavation and

refilling and secured with holding clamps, bolts, nuts, etc. as

26 Each 4318 112268.00

7.10 Supply of Façade Lighting Luminaries integral flood light(

Fitting+Controll gear+Bulb) single piece pressure die cast

aluminiam housing toughned glass cover (IP65 ) ingress

protection and rectangular reflacter for planer symetic optical

distribution.

8 Each 10544.00 84352

SWF33I IXSONT250W S

7.11 Installation and commissioning of Flood Light Luminaries

with all acessories in suitale high angle frame stand Complete

in All Respect etc.

8 Each 1000 8000

7.12 Supply And Fixing of angle frame stand made 25 X 5 mm

angle for flood Light

4 Each 3000 12000

TOTAL SUB HEAD (VI) 112268.00 644643.00

SUB HEAD (VII):- Cable and its Laying


PVC Conduits)7.1 N.A. Supply of ISI marked XLPE insulated cable as per IS 7098,

armoured, served, sheathed 1100 volts grade,Make:- (Havells

or Equivalent)7.1.a N.A. 3.5CX400 Sqmm Al XLPE insulated Armoured Cable 150 Metre 2577.00 386,550.00

7.1.c N.A. 3.5CX150 Sqmm Al XLPE insulated Armoured Cable 150 Metre 1075.00 161,250.00

7.1.d N.A. 3.5CX70 Sqmm Al XLPE insulated Armoured Cable 300 Metre 585.00 175,500.00

7.1.e N.A. 3.5CX35 Sqmm Al XLPE insulated Armoured Cable 50 Metre 323.00 16,150.00

7,1,h N.A. 4CX16 Sqmm AL XLPE insulated Armoured Cable 500 Metre 218.00 109,000.00

7,1,g N.A. 3CX16 Sqmm AL XLPE insulated Armoured Cable 50 Metre 184.00 9,200.00

7.2 7.1 Laying of one number PVC insulated and PVC sheathed /

XLPE power cable of 1.1 KV grade of following size direct in

ground including excavation, sand cushioning, protective

covering and refilling the trench etc as required.7.2.a 7.1.1 Upto 35 sq. mm 600 Metre 195.00 117000.00

7.2.b 7.1.2 Above 35 sq. mm and upto 95 sq. mm 300 Metre 202.00 60600.00

7.2.c 7.1.3 Above 95 sq. mm and upto 185 sq. mm 150 Metre 210.00 31500.00

7.2.d 7.1.4 Above 185 sq. mm and upto 400 sq. mm 150 Metre 233.00 34950.00

7.3 9.1 Supplying and making indoor end termination with brass

compression gland and aluminium lugs for following size of

PVC insulated and PVC sheathed / XLPE aluminium

conductor cable of 1.1 KV grade as required.7.3.a 9.1.31 3½ X 400 sq. mm (82mm) 2 Each 1369.00 2738.00

7.3.c 9.1.26 3½ X 150 sq. mm (50mm) 2 Each 576.00 1152.00

7.3.d 9.1.23 3½ X 70 sq. mm (38mm) 4 Each 382.00 1528.00

7.3.e 9.1.21 3½ X 35 sq. mm (32mm) 2 Each 270.00 540.00

7,3,f 9.1.33 4 X 16 sq. mm (28mm) 8 Each 245.00 1960.00

TOTAL SUB HEAD (VII) 251,968.00 857,650.00

SUB HEAD (VIII):- EARTHING

8.1 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm

thick including accessories, and providing masonry enclosure

with cover plate having locking arrangement and watering

pipe of 2.7 metre long etc. with charcoal/ coke and salt as

2 Set 9292.00 18,584.00

8.2 5,4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm

thick including accessories, and providing masonry enclosure

with cover plate having locking arrangement and watering

pipe of 2.7 metre long etc. with charcoal/ coke and salt as

10 Set 4490.00 44,900.00

8.3 5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm

dia G.I. pipe from earth electrode including connection with

brass nut, bolt, spring, washer excavation and re-filling etc. as

20 Metre 1082.00 21,640.00


PVC Conduits)8.4 5,11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia

G.I. pipe from earth electrode including connection with G.I.

nut, bolt, spring, washer excavation and re-filling etc. as

100 Metre 421.00 42,100.00

8.5 5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including

accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. with

6 Nos 3926.00 23,556.00

8.6 5.12 Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode

including connection with G.I. thimble excavation and

60 Meter 151.00 9,060.00

TOTAL SUB HEAD (VIII) 159,840.00 0.00

SUB HEAD (IX) : LIGHTNING CONDUCTORS

9.1 6.1 Providing and fixing of lightning conductor finial, made of 25

mm dia 300 mm long, copper tube, having single prong at top,

with 85 mm dia 3 mm thick copper base plate including holes

etc. complete as required.

1 Each 764.00 764.00

9.2 6.4 Jointing copper / G.I. tape (with another copper/ G I tape, base

of the finial or any other metallic object) by riveting / nut

bolting/ sweating and soldering etc as required.

10 Each 72.00 720.00

9.3 6.5 Providing and fixing copper tape 20 mm X 3 mm thick on

parapet or surface of wall for lightning conductor complete as

required.(For horizontal run)

150 Metre 376.00 56,400.00

9.4 6.6 Providing and fixing copper tape 20 mm X 3 mm thick on

parapet or surface of wall for lightning conductor complete as

required.(For vertical run)

70 Metre 406.00 28,420.00

TOTAL SUB HEAD (IX) 86,304.00 0.00

SUB HEAD (X):- MISCELLANEOUS

10.1 2.21 Providing and fixing M.V. danger notice plate of 200 mm X

150mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single

red colour on front side as required.

2 Each 141 282

10.2 N.A Supply and fixing of shock treatment chart (prescribed under

I.E. rules) duly framed with glass and supported from back

with hard board with supply of all material labour T & P etc

for proper completion of work.

1 Each 1458.00 1458

10.3 N.A Supply, fixing, testing, commissioning of 1800mm x 900mm

x 20mm thick chequered rubber matting of tested quality to

with stand 11 KV dielectric strength complete in all respects.

1 Each 5787.00 5787

10.4 N.A Supply of 11 KV grade rubber hand gloves in pair as per IS 2 Each 1104.00 2208


PVC Conduits)10.5 N.A Supply and fixing of fan box with hexagonal side of approx.

80mm in length fabricated from 18 SWG MS sheet

incorporating with 10 mm dia MS round bar duly bent for

supportiong fan hanger painted with red oxide and screwing

arrangement with wiring conduit laid in the RCC roof before

concreting along with supply of all materials, labour, T&P etc.

123 Each 122.00 15006

10.6 NA Dismantling of Electrical Existing Lighting Equipment Like

Fitting, Conduit Pipe, Wire,SDB, Switch Board, Fan, Exhaust,

Panel etc And All material hand over to department in their

relative store

1 Job 75000.00 75000

Total Of Sub Head (X) 282 99459

11 NA Supplying of following KVA compact packaged silent type

D.G Set (With acoustic enclosure to reduce the noise level as

per requirements of central pollution control board) 415Volts,

3 phase, 50 Hz AC alternator coupled to diesel engine

complete with all accessories, standard specifications tool

kits, service manual, self starting device, fly wheel, coupling

with guard, V velt, radiator, instrument panel (starting switch

with key, Water Temperature indicator gauge, Lub OIl

Pressure gauge, Lube oil temperature gauge, Battery Charging

AmMetre, indicating lamp, hour counter etc.), residential type

silencer, common bed plate, anti vibration isolation pads,

grouting bolts, first charge of engine oil, gear oil, high speed

diesel oil, 24 volt / 12 volt chargeable battery set with Trickle

/ Boost Battery charger complete as required including

erecting, testing and commissioning of following type 415

Volts, 3 phase, 50 Hz. AC alternator coupled to Diesel Engine 125 KVA D.G. Set (with fuel tank for 6 hrs full load

operation outside the Canopy)

0 Nos 596000.00 0

TOTAL SUB HEAD (XI) 0 0

DSR 2014 NON-DSR

ISANITARY

INSTALLATIONS & C.P.

FITTINGS

185608.80 75800.00

IISOIL WASTE & VENT

PIPES AND FITTINGS554386.65 28800.00

IIIINTERNAL & EXTERNAL

WATER SUPPLY WORKS313065.20

IV SEWERAGE SYSTEM 98464.10

V EXTERNAL PLUMBING 1279305.00

TOTAL 2430829.75 104600.00

GRAND TOTAL

SAY

2535429.75

2535430.00

SCHEDULE OF QUANTITIES FOR PLUMBING WORKS

PROPOSED RENOVATION WORK OF HOSTEL BLOCK E

FOR N.I.T., RAIPUR (CHATTISGARH)

SUMMARY OF COST INTERNAL PLUMBING WORKS

S.NO NAME OF SUB-HEADAMOUNT

SL.

NO

DSR

2014DESCRIPTION UNIT QTY

RATE

(in Rs)

AMOUNT

(in Rs)

ISanitary Instatllations

1 17.1 Providing and fixing water closet squatting pan ( Indian type

W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low

level white P.V.C. flushing cistern with manually controlled

device (handle lever) conforming to IS:7231,

Parryware/Hindware/Seabird/Orient (Coral) with all fittings and

fixtures complete including cutting and making good the walls

and floors wherever required.17.1.

1

White Vitreous china Orissa pattern W.C. pan of size

580x440mm with integral type foot rests each 6.00 3392.80 20356.80

2 17.2 Providing and fixing white vitreous china pedestal type water

closet (European type W.C. pan) with seat and lid, 10 litre low

level white P.V.C. flushing cistern with manually controlled

device (handle lever), conforming to IS : 7231,

Parryware/Hindware/Seabrid /Orient (Coral) with all fittings

and fixtures complete including cutting and making good the

walls and floors wherever required : 17.2. W.C. pan with ISI marked black solid plastic seat and lid each 12.00 3293.05 39516.60

3 17.7.

4

Providing & fixing white vitreous china wash basin with C.I.

brackets painted white, 15 mm C.P. brass pillar taps, C.P.

brass chain with rubber plug, 32mm C.P. brass waste of

standerd pattern including cutting & making good the walls

wherever required. a)White Vitreous China Flat back wash Basin size 550x400 mm

with single 15 mm C.P. brass pillar tap. each 18.00 1807.10 32527.80

4 17.3 Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.17.28

.1

Semi rigid pipe

17.28

.1.1

32 mm dia each 18.00 76.75 1381.50

17.28

.1.2

40 mm dia each 1.00 82.60 82.60

SCHEDULE OF QUANTITIES FOR PLUMBING WORKS PROPOSED RENOVATION WORK OF HOSTEL BLOCK E FOR N.I.T., RAIPUR (CHATTISGARH)

INTERNAL PLUMBING WORKS

SANITARY INSTALLATIONS & C.P FITTINGS

5 17.3 Providing and fixing 600x450mm bevelled edge mirror of

superior glass (of approved quality) complete with 6mm thick

hard board ground fixed to wooden cleats with C.P. brass

screws and washers complete. each 18.00 793.95 14291.10

6 17.10 Providing and fixing Stainless Steel AISI 304 (18/8) kitchen

sink as per I.S. 13983 with C.I. brackets and stainless steel

plug 40 mm including painting of fittings and brackets, cutting

and making good the walls wherever required :17.10

.1

Kitchen sink with drain board

17.10

.1.1

510x1040mm bowl depth 250mm each 1.00 7052.15 7052.15

CP Brass fittings7 18.2 Providing and fixing unplasticised PVC connection pipe with

brass unions18.21

.2

45 cm length

18.21

.2.1

15 mm nominal bore each 55.00 68.60 3773.00

8 18.5 Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:893118.49

.1

a) 15 mm nominal boreeach 18.00 459.50 8271.00

9 18.5 Providing and fixing C.P. brass long body bib cock of approved

quality conforming to IS standards and weighing not less than

690 gms.18.51

.1


10 18.5 Providing and fixing C.P. brass angle valve for basin mixer and

gyser points of approved quality conforming to IS:893118.53

.1


11 18.2 Providing and fixing C.P. brass shower rose with 15 or 20mm 18.22

.2

150 mm diameter each 18.00 86.35 1554.30

12 Providing and fixing C.P. brass stop cock (concealed) of

standard design and of approved make conforming to IS:8931:18.52.115mm nominal bore each 18.00 619.75 11155.50

TOTAL [I] 185608.80

II

1 Providing & fixing soil, waste and vent pipes.17.35.1.2a) 100mm dia centrifugally cast iron S & S pipe. Rm. 100.00 917.75 91775.00

17.35.2.2b) 75mm dia centrifugally cast iron S & S pipe. Rm. 200.00 791.30 158260.00

2 Providing lead caulked joints to sand cast iron/centrifugally cast

(spun) iron pipes & fitting of diameters.17.58.1a) 100mm No. 71.00 243.75 17306.25

17.58.2b) 75mm No. 142.00 205.30 29152.60

3 Providing & fixing M.S. holder bat clamps of approved design to

sand cast iron/centrifugally cast (Spun) iron S & S pipe

embeded in & including cement concrete blocks 10x10x10cm.

of 1:2:4 mix (1 cement : 2 coarse : 4 graded stone aggregate size). Including cost of cutting holes & making good the walls

etc.17.37.1a) for 100mm dia pipe. No. 28 152.90 4281.20

17.37.2b) for 75mm dia pipe. No. 56 150.60 8433.60

4 Providing & fixing cast iron trap of self cleansing design with or

without ventarm complete, including cost of cutting & making

good the walls & floors.17.60.2.1a) 100mm inlet & 75mm outlet. No. 50.00 1020.90 51045.00

5 Providing & fixing cast iron coller.17.57.1.2a) 100mm dia. No. 50.00 318.35 15917.50

17.57.2.2b) 75mm dia. No. 100.00 219.75 21975.00

6 Providing and fixing plain cast iron S & S sanitary bend.17.39.1.2a) 100mm Nos. 22.00 335.75 7386.50

17.39.2.2b) 75mm Nos. 9.00 248.80 2239.20

7 Providing and fixing bend of required degree with access door,

insertion rubber washer 3mm thick, bolts and nuts complete.17.38.1.2a) 100mm Each 0.00 385.70 0.0017.38.2.2b) 75mm Nos. 1.00 318.50 318.50

8 Providing and fixing centrifugaly cast iron single equal plain

junction of required degree. 17.44

.1.2

100x100x100mm Nos. 18 576.20 10371.60

SOIL WASTE & VENT PIPES AND FITTINGS

17.44

.2.2

75x75x75mm Nos. 24 405.60 9734.40

9 Providing and fixing cast iron terminal guard. 17.56

.1.2

100 mm Nos. 4 434.50 1738.00

17.56

.2.2

75 mm Nos. 8 370.75 2966.00

10 DSR

no.19

.2.1

Providing and laying cement concrete 1:5:10(1 cement : 5

coarse sand : 10 graded stone aggregate 20mm nominal size)

around P.V.C Soil and waste pipe including bed concrete as per

standard design(embedded in the flooring / ground)100 mm dia metre 50.00 592.60 29630.00

75 mm dia metre 100.00 340.00 34000.00

11 12.41 Providing and fixing on wall face unplasticised-Rigid PVC rain

water pipes conforming to IS: 13592 Type A including jointing

with seal ring conforming to IS: 5382 leaving 10mm gap for

thermal expansion. 12.41

.2

110 mm Metre150.00

231.6534747.50

12 12.42 Providing and fixing on wall face unplasticised PVC moulded

fittings/accessories for unplasticised Rigid PVC rain water pipes

conforming to IS:13592 Type A including jointing with seal

ring conforming to IS:5382 leaving 10mm gap for thermal 12.42

.5.2

Bend 87.5 degree

12.42

.5.2

110 mm Bend Each13.00

161.552100.15

12.42

.6

Shoe (Plain)

12.42

.6.2

110 mm Shoe Each13.00

295.103836.30

13 12.43 Providing and fixing unplasticised-PVC pipe clips of approved

design to unplasticised-PVC rain water pipes by means of

50x50x50 mm hard wood plugs, screwed with MS screws of

required length including cutting brick work and fixing in

cement mortar 1:4 (1 cement : 4 coarse sand) and making

good the wall etc. complete. 12.43

.2

110 mm Each78.00

189.0514745.90

14 12.22 Making khurras 45x45 cm with average minimum thickness of

5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over PVC

sheet 1m x 1 m x 400 micron, finished with 12 mm cement

plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement,punning,rounding the edges and making and finishing Each 13.00 186.65 2426.45

TOTAL [II] 554386.65

III

1 Providing and fixing GI pipes complete with GI fittings

and clamps, including cutting and making good walls etc.

(internal work).Internal work-Exposed on wall

18.10.115mm dia nominal bore Metre 135 215.10 29038.50







2 Painting GI pipes and fittings with SYNTHETIC enamel paint

over a ready mixed priming coat, both of approved quality for

new work.18.38.115mm dia nominal bore Metre 135 9.60 1296.00







3 Providing and fixing GI Union in GI pipes including cutting and

threading the pipe and making long screws etc. complete (new

work).18.46.115mm dia nominal bore Metre 45 165.25 7436.25







INTERNAL & EXTERNAL WATER SUPPLY WORKS

418.17

Providing and fixing gun metal gate valve with wheel of

approved quality.18.17.1a) 25mm dia nominal bore Each 7.00 428.85 3001.9518.17.2b) 32mm dia nominal bore Each 6.00 501.50 3009.0017.17.3c) 40mm dia nominal bore Each 2.00 585.50 1171.0018.17.4d) 50mm dia nominal bore Each 6.00 750.75 4504.5018.17.5e) 65mm dia nominal bore Each 0.00 1286.25 0.00

5 18.48 Providing and placing on terrace (at all floor levels)polyethylene

water storage tank ISI : 12701 marked indicating the BIS

License No. with cover and suitable locking arrangement and

making necessary holes for inlet, outlet and over flow pipes but

without fitting and base support for tank.[Sintex, Electroplast,

Star, Lotus or equivalent having valid ISI license].Capcity in Liters Per Ltrs 20000.00 7.25 145000.00

6 18.16 Providing and fixing brass stop cock of approved quality.18.16.2a) 20 mm nominal bore Nos. 0.00 344.85 0.00

TOTAL[III] 313065.20

IV

1 2.10 Excavating trenches of required width for pipes, cables etc.

including excavation for sockets and dressing of sides,

ramming of bottoms, depth upto 1.5m including getting out the

excavated soil, and then returning the soil as required, in

layers not exceeding 20cm in depth including consolidating

each deposited layer by ramming, watering etc. and disposing

of surplus excavated soil as directed, within a lead of 50m.2.10.1 All kinds of soil2.10.1.2Pipes, cables etc. exceeding 80mm dia but not exceeding metre 50.00 208.30 10415.00

2 19.1 Providing, laying and jointing glazed stoneware pipes grade 'A'

with stiff mixture of cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of joints etc. complete.19.1.1 100mm diameter metre 5.00 206.55 1032.75

19.1.2 150mm diameter metre 45.00 314.35 14145.75

3 19.2 Providing and laying cement concrete 1:5:10 (1 cement: 5

coarse sand : 10 graded stone aggregate 40mm nominal size)

all round S.W. pipes including bed concrete as per standard 19.2.1 100mm dia SW pipe metre 5.00 592.60 2963.00

19.2.2 150mm dia SW pipe metre 45.00 724.70 32611.50

SEWERAGE SYSTEM

4 19.4 Providing and fixing square-mouth S.W. gully trap grade‘A’

complete with C.I. grating, brick masonry chamber with water

tight C.I. cover with frame of 300 x300 mm size (inside) the

weight of cover to be not less than 4.50 kg and frame to be not

less than 2.70 kg as per standard design19.4. 150 x 100 mm size P type19.4.

2.2

With Sewer bricks conforming to IS : 4885each 1.00 1664.80 1664.80

7 19.7 Constructing brick masonry manhole in cement mortar 1:4 (1

cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement

:2 coarse sand :4 graded stone aggregate 20mm nominal

size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand

:8 graded stone aggregate 40mm nominal size) inside

plastering 12mm thick with cement mortar 1:3 (1 cement :3

coarse sand) finished with floating coat fo neat cement and

making channels in cement concrete 1:2:4 (1 cement :2 coarse

sand :4 graded stone aggregate 20mm nminal size) finished

8 19.7.1 Inside size 90x80cms and 45cms deep including CI cover with

frame (light duty) 455x610mm internal diamensions total

weight of cover and frame to be not less than 38 kg (weight of

cover 23 kg and weight of frame 15kg).19.7.1.1With FPS bricks of class designation 75

(i) For Sewer Line each 3.00 8507.00 25521.00

9 Extra for depth for manholes: 19.8.1.1Size 90x80cm with FPS bricks (class I ). metre 1.50 5638.20 8457.30

10 19.2 Providing M.S. foot rests including fixing in manholes with

20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3

coarse sand :6graded stone aggregate 20 mm nominal size) as

per standard design19.15.1With 20x20 mm square bar each 6.00 275.50 1653.00

TOTAL[IV] 98464.10

V

1 NSR Extra for providing & fixing 125 mm dia C.P. grating in place

of C.I. grating over floor traps. Each 50.00 80.00 4,000.00

NON SCHEDULED ITEMS

SANITARY INSTALLATIONS & C.P FITTINGS

2 NSR Providing & fixing 60x2cm. C.P. brass towelrail complete with

C.P. brass brackets fixed to wooden cleats with C.P. brass

screw.PARRYWARE C9948 Each 18.00 1200.00 21600.00

3 NSR Supplying & Fixing of CP soap tray fixed to the wall with PVC

rubber plug with CP brass screws Each 18.00 800.00 14400.00

4 NSR Providing and Fixing C.P. brass Ablution health faucet assembly

with 1.2 m long braided PVC hose with mounting bracket fixed

on wall complete.[FOR EWC] Each 12.00 500.00 6000.00

5 NSR Providing and fixing C.P. brass Two-way angle valve for EWC

points & for fixing Ablution Health Fauct of approved quality

conforming to IS:8931. 15 mm nominal bore Each 12.00 1400.00 16800.00

6 NSR Constructing brick masonary INSPECTION chamber 60x60x60

cm with bricks of class designation 50 in cement mortar 1:4 (1

cement : 4 coarse sand) including CI cover with frame LIGHT

WEIGHT complete as per design. With FPS bricksEach 2.00 6500.00 13000.00

TOTAL [V] 75800.00

VI

1 NSR Providing and fixing G.I Inlet fitting with 2 inlets 75 mm size

fabricated from 100 mm dia G.I pipes(approx. length=150mm

to 300mm) and welded G.I sockets, fixed to CI trap with lead

caulked joint and set in cement concrete as per standard

drawing including cost of Bitumastic paint complete. Each 24.00 1200.00 28800.00

TOTAL [VI] 28800.00

CI PIPES & FITTINGS

S.N. Description D.S.R. - Qty. Unit Rate (Rs.) Amount (Rs.)SEPTIC TANKSize :- Length = 7.50 M. Width = 2.65 M

Total Depth =2.50M

1 Earth work in excavation over areas including

disposal of excavated earth, lead upto 50m,

disposed earth to be levelled and neatly dressed.In all kind of soil upto 1.5m depth 2.6.1 39.520 Cum 155.60 6149.31

In all kind of soil upto 1.5m to 3.0m. depth 2.6.1&2.26 29.290 Cum 201.85 5912.19

2 Providing and laying of cement concrete in base

excluding the cost of centring and shuttering by

1:2:4 (1 cement : 2 coarse sand : 4 gradded

stone aggregae 40mm nominal size)4.1.3 4.635 Cum 5466.30 25336.30

3 Brick work with brick of class designation 150 in

foundation and plinth in cement mortar (1

cement : 4 coarse sand) 6.1.1 24.897 Cum 4918.65 122459.63

4 Reinforced cement concrete work in slab with

1:2:4 (1 cement : 2 course sand : 4 graded

stone aggregate 20mm normal size). 5.3 4.242 Cum 6778.2 28753.12

5 Reinforcement for R.C.C. work including,

straightening, cutting bending binding and

placing in position complete. 5.22.1 320.000 Kg 64.95 20784.00

6 Centring and shuttering including struting ,

proping etc and removal of form for slab. 5.9.3 20.000 Sqm 401.65 8033.00

7 15mm cement plaster on rough side of mix 1:4

(1 cement : 4 coarse sand) 13.2.1 65.550 Sqm 189.40 12415.17

8 Providing M.S. foot rest including fixing with

20x20x10 cm. cement concrete block 1:3:6 (1

cement : 3 coarse sand : 6 gradded aggregate

of nominal size 20mm ) as per standard design

with 20x20mm sq bars.19.15.1 12.000 Nos. 275.50 3306.00

ESTIMATE FOR EXTERNAL PLUMBING WORKSPROPOSED RENOVATION WORK OF HOSTEL BLOCK E FOR N.I.T., RAIPUR (CHATTISGARH)

PART - A (SCHEDULED ITEMS AS PER D.S.R 2014)

9 Providing and fixing C.I. tee at the inlet and

outlet of septic tank. 7087 2.000 Nos. 600.00 1200.00

10 Providing & fixing 75mm dia vent pipes. 17.35.2.1 1.000 Rm. 709.10 709.10

11 Providing & fixing of 75mm dia cast iron terminal

guard. 17.56.2.1 1.000 No. 197.7 197.70

12 Providing and fixing in position precast RCC

manhole cover and frame of required shape and

approved quality.M.D. -10- Circular shape 500mm internal 19.19.2.2 2.000 No. 909.25 1818.50

M.D. -2.5- Circular shape 450mm internal 19.19.1.3 4.000 No. 902.80 3611.20

13 Making soak pit 2.5 m diameter 3.0 metre deep

with 45 x 45 cm dry brick honey comb shaft with

bricks of class designation 75 and S.W. drain

pipe 100 mm diameter, 1.8m long complete as

per standard design.With F.P.S. bricks 19.32.1 2.000 No. 18309.50 36619.00

TOTAL 277304.22

1 Excavating trenches in all kind of soil of required

width for pipes, cables etc. including excavation

for sockets and dressing of sides, ramming of

bottoms, depth upto 1.5 m. including getting

out the excavated soil & then returning the soil

as required,in layers not exceeding 20cm in depth including

consolidating each deposited layer by ramming,

watering, etc & disposig of surplus excavated soil

as directed within a lead of 50m.a) Pipes 80mm to 300mm diameter. 2.10.1.2 125 RM 208.30 26037.50

2 Providing, laying and joining glazed stone ware

pipes grade 'A' with stiff mixture of cement

mortar in the proportion of 1:1 (1 cement : 1

fine sand) including testing of joints etc. a) 150mm diameter 19.1.2 125 M 314.35 39293.75

SCHEDULE OF QUANTITIES FOR EXTERNAL

3 Providing & laying cement concrete 1:5:10 (1

cement :5 coarse sand :10 graded stone

aggregate 40mm nominal size) alround S.W.

Pipes including bed concrete as per standard a) 150mm diameter S.W. Pipe 19.2.2 125 M 724.70 90587.50

4 Constructing brick masonry manhole in cement

mortar 1:4 (1 cement :4 coarse sand) RCC top

slab with 1:2:4 mix (1 cement :2 coarse sand :4

graded stone aggregate 20mm nominal size),

foundation concrete 1:4:8 mix (1 cement :4

coarse sand :8 graded stone aggregate 40mm

nominal size) inside plastering 12mm thick with

cement mortar 1:3 (1 cement :3 coarse sand)

finished with floating coat fo neat cement and

making channels in cement concrete 1:2:4 (1

cement :2 coarse sand :4 graded stone

aggregate 20mm nminal size) finished with a

19.7

Inside size 90x80cms and 45cms deep including

CI cover with frame (light duty) 455x610mm

internal diamensions total weight of cover and

frame to be not less than 38 kg (weight of cover

23 kg and weight of frame 15kg).With common burnt clay FPS (non modular)

bricks of class designation 75

19.7.1

(i) For Sewer Line 19.7.1 4.00 each 8507.00 34028.00

Inside size 90x120cms and 90cms deep

including CI cover with frame (MEDIUM duty)

455x610mm internal diamensions total weight of

cover and frame to be not less than 116 kg

(weight of cover 58 kg and weight of frame With common burnt clay FPS (non modular)

bricks of class designation 7519.7.2

(i) For Sewer Line 19.7.2.1 2.00 each 18304.45 36608.90

Extra for depth for manholes: Size 90x80cm with With common burnt clay FPS

(non modular) bricks of class designation 7.5 19.8.1.1 2.00 metre 5638.20 11276.40

Size 90x120cm with With common burnt clay

FPS (non modular) bricks of class designation 19.8.2.1 1.00 metre 6753.65 6753.65

5 Providing orange colour safety foot rests of

minimum 6 mm thick plastic encapsulated as per

IS:10910 on 12 mm dia steel bar conforming to

IS:1786 having minimum cross section as 23

mm x 25 mm and over all minimum length 263

mm and width as 165 mm with minimum 112

mm space between protruded legs having 2 mm

thread on top surface by ribbing or chequering

besides necessary and adequate anchoring

projections on tail length on 138 mm as per

standard drawing and suitable to with stand the

bend test and chemical resistance test as per

specifications and having manufacture's

permanent identification mark to be visible even

after fixing, including fixing in manholes with

30x20x15 cm cement concrete block 1:3:6 (1

cement : 3 coarse sand : 6 graded stone

aggregate 20 mm nominal size) complete as per

19.16 12.00 each 311.60 3739.20

TOTAL 248324.90

EXTERNAL WATER SUPPLY SYSTEM

1 Providing & fixing G.I. pipes complete with G.I.

fittings including trenching and refilling etc.

(external work)65mm nominal bore. 18.12.7 100 Rm. 524.25 52425.00

50mm nominal bore. 18.12.6 100 Rm. 399.50 39950.00

40mm nominal bore. 18.12.5 30 Rm. 334.15 10024.50

2 Supplying and fixing of specials for pressure 10% of item no.7 10239.95

3 Providing and fixing gate valve (with cap

complete with bolts, nuts, rubber insertion etc.65mm nominal bore. 18.17.5 1 Nos. 1287.75 1287.75

50mm nominal bore. 18.17.4 2 Nos. 750.75 1501.50

40mm nominal bore. 18.17.3 30 Nos. 585.50 17565.00

4 Constructing brick masonry chamber 600 x

600 x 750 mm inside with F.P.S. brick work

in cement mortar 1:4 (1 cement : 4 coarse

sand) for Sluice Valve / Air Valve, with C. I.

surface box 100 mm top diameter, 160 mm

bottom diameter and 180mm deep (inside) with

chained lid and RCC top slab with 1 : 2 : 4 mix

(1 cement : 2 coarse sand : 4 grade stone

aggregate 20 mm nominal size); necessary

excavation, foundation concrete 1:5:10 (1

cement : 5 fine sand: 10 graded stone

aggregate 40 mm nominal size) and inside

plastering with cement mortar 1 : 3 (1 cement

: 3 coarse sand ) 12 mm thick finished with a

floating coat of neat cement complete as per 18.33.1 2.00 Each 6754.30 13508.60

5 Constructing brick masonry chamber 900 x

900 x 1000 mm inside with F.P.S. brick work in

cement mortar 1:4 (1 cement: 4 coarse sand)

for Sluice Valve, with C.I.surface box 100 mm

top diameter, 160 mm bottom diameter and 180

mm deep (inside) with chained lid and RCC top

slab with 1:2:4 mix (1 cement: 2 coarse sand:4

grade stone aggregate 20mm nominal size);

necessary excavation, foundation concrete

1:5:10 (1 cement :5 fine sand: 10 graded stone

aggregate 40mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement:3

coarse sand ) 12 mm thick finished with a

floating coat of neat cement complete as per 18.34.1 1.00 Each 11673.35 11673.35

TOTAL 158175.65

DRAINAGE SYSTEM

1 Constructing brick masonry open surface drain

with bricks of class designation 75 in cement

mortar 1:4 (1 cement : 4 fine sand) including

earth excavation, 10cm thick bed concrete

1:5:10 (1 cement : 5 fine sand : 10 graded

stone aggregate 40mm nominal size) and 25mm

thick cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 12.5mm

nominal size) for filling haunches including

12mm cement plaster 1:4 (1 cement : 4 coarse

sand ) with a floating coat of neat cement inside

the drain, its top and exposed side including

30cm drain 45cm average depth A.R. 150.00 Metre 1970.00 295500.00

45cm drain 60cm average depth A.R. 50.00 Metre 3000.00 150000.00

2 OVER HEAD WATER TANK AT PLINTH AREA

RATE OF 10KL 150000.00

TOTAL 595500.00

GRAND TOTAL 1279304.77

SAY 1279305.00

Sub Head Description As per NS

I Fire Suppression System Rs.281,864.00

Total C/F To Summary Rs.281,864.00

Total Rs.281,864.00

Name of Project : NIT RAIPUR HOSTEL BLOCK E

Name of Work : Estimate of Fire Fighting System

Project Summary

Sl.No. Description Unit Qty. Rate

Non DSR

Amount

Sub Head (I) - Fire Suppression

15 Supply and fixing CO2 type fire

extinguishers 4.5 kg. capacity(ISI Marked

IS: 2878 & TAC approved) complete with

initial charge and wall bracket, along with

supply of all materials and labour for

proper completion of work. Each 15 9874.00 148110.00

16Supply and fixing of fire extinguishers dry

chemical type 6 kg. capacity (ISI Marked

IS: 15683 & TAC approved) complete

with initial charge and wall bracket, along

with supply of all materials and labour for

proper completion of work. Each 15 8842.00 132630.00

17Supply and fixing of fire bucket, round

bottom made of G.I. sheet 9-11 litres

capacity duly painted as per fire brigade

design, supported on hanging bracket

chained and locked, initially filled with fine

river sand, water as per directions of

Engineer-in-Charge. Each 4 281.00 1124.00

Total Sub Head (I) 281864.00

NIT RAIPUR HOSTEL BLOCK E

Estimate of Fire Fighting System

renovation of hostel 'e' block of national … · steel work 9.200 19 providing and...

Documents