reworking bga high value test interface pcb’s + burn in pcb
TRANSCRIPT
Reworking BGA High Value Test interface PCB’S
+Burn in PCB
Overview
Test Interface (TIU PCB‘s) are extremely expensive.
BGA chipsets are developed on these thick PCB circuits, these designs test for speed and functionality of the Firmware
Time to market during development of BGA Chipset is critical to product Marketing needs.
Unusual components used in development and difficult to rework.
PCB up to 44 layers 6mm thick.
Low volume PCB made as cost is extremely high of PCB also
difficult to assemble.
Confidential and Proprietary to OK International. © OK International All rights reserved.
Examples of development BGA Pcbs
3
Cost of these TIU PCB can easily start at $30,000
Confidential and Proprietary to OK International. © OK International All rights reserved.
Challenges of TIU Rework
Massive size and thermal mass of PCB substrate Mountains
Thermal power required to rework 3-6mm thick PCB’S.
Surface mount relays need solder paste printed to replace.
Plastic inductors and part on underside will melt easily if heating from below is to high.
Heating to much from top will burn top of PCB so a important balance is required.
Dual heating zones from preheater make this rework possible not possible without this technology from OK/Metcal.
Confidential and Proprietary to OK International. © OK International All rights reserved.
Rework process
Probe Card Relay Rework process
Heat PCB up to approximately 100c from bottom Preheaters (with inner and outer heaters explained later),on simultaneously but at different temperatures this stops damage to underside components.
A custom metal conduction tip is used with Metcal technology to add additional heat to solder connections without heating adjacent components in 8-10 secs.
The relay is discarded when this conduction process is used.
If the component needs to be analyzed for any internal faults then convection technology is used as in next slide.
The component pcb pads are then printed with solder paste with mini custom stencils.
The New part replacement is done on APR-5000XLS with camera to align and place component. Reflow is done with convection profile in APR-5000XLS
5
Confidential and Proprietary to OK International. © OK International All rights reserved.
TIU Probe Card (conduction tool)
Confidential and Proprietary to OK International. © OK International All rights reserved.
Probe Card
7
Movie shows conduction removal with PCB at 100°c
Confidential and Proprietary to OK International. © OK International All rights reserved.
APR-5000 Description
8
Vacuum tube
Dual Preheater
zone
Main power switch Manual
heater head
controls
Board Holders
Inspection camera
Heater Head
Thermo-couples
Confidential and Proprietary to OK International. © OK International All rights reserved. 9
Relay removed with conduction
Confidential and Proprietary to OK International. © OK International All rights reserved.
Probe Card (Mini stencil)
Confidential and Proprietary to OK International. © OK International All rights reserved.
Examples of TIU PCB’s on Metcal APR 5000XLS hot air rework station
Confidential and Proprietary to OK International. © OK International All rights reserved.
Removing GRF303 Relays
12
Once you mount the TIU on the APR5000, you need to prepare the following equipment:
Metcal MX5000 with Customized conduction tip cartridge PN: SMTC-8RND86.
Confidential and Proprietary to OK International. © OK International All rights reserved.
Probe Card (For Close packaging a machined nozzle is used)
Confidential and Proprietary to OK International. © OK International All rights reserved.
Reflow profile for hot air replacement
Confidential and Proprietary to OK International. © OK International All rights reserved.
Conclusion
Removal done with hot air and custom conduction tools to remove parts fast while pcb is preheated to 100°c
PCB old solder is cleaned with solder tools and wick on preheated PCB so not to damage pads.
Solder paste is printed onto PCB cold with mini stencils made for each part.
Component is placed under vision on rework machine onto pasted PCB pad.
Rework machine can now reflow part back onto pcb without damage.
Removal time 400 secs preheat and 10 secs per device with conduction tool.
Placement is 400sec preheat and total time of 10-12 mins.
15
Confidential and Proprietary to OK International. © OK International All rights reserved.
Contact details
OK International Ltd.
Eagle Close, Chandlers Ford
SO53 4NF, Hampshire, U.K.
Tel: +44 (0)2380 489 100
European Contact
Andy Cotton – [email protected]
North America Contact
Paul Wood – [email protected]
www.okinternational.com www.metcal.com
16
Confidential and Proprietary to OK International. © OK International All rights reserved.
Thank you
17
global sales and service network
leading edge design and simulation tools
comprehensive assembly and post assembly test
the largest ATE PCB provider in the world
Integrated solutions
ATE boards featured here, courtesy of
Contact details for Multitest [email protected] http://www.multitest.com/eng/