roboworld kuka kr180-pa robosuit installation instructions
DESCRIPTION
Roboworld KUKA KR180-PA Robosuit Installation Instructions. Version 10/10. - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/1.jpg)
Roboworld KUKA KR180-PA Robosuit Installation Instructions
Version 10/10
![Page 2: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/2.jpg)
Be sure to remove any valve packs, j-box, brackets, etc from the robot before beginning this process. The suit is designed to fit the casting of the robot only. If the
robot is dirty, it is suggested that it be cleaned as well before suit installation.
• NOTE:• It is recommended that the suit be
installed with the adhesive backed Velcro attached to the suit. Once the individual suit pieces are properly installed on the robot, the adhesive sided Velcro must be attached to the robot to stabilize the suit for high speed operation.
![Page 3: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/3.jpg)
If you have received a stationary base cover, install this first. Be careful to cut hole in gum-rubber panel for hard stop.
![Page 4: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/4.jpg)
Install joint 3 Servo Motor Cap
![Page 5: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/5.jpg)
Install the upper arm section. Picture sequence 1,2,3 and 4 (over next few pages) show the proper method. The flexible conduit remains inside the suit and can be accessed using the two "gooseneck" panels. If the conduit is not used, attach the supplied flat
Velcro panels. Note how the joint 3 servo motor cap attaches to this piece.
1
![Page 6: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/6.jpg)
Picture 2
2
![Page 7: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/7.jpg)
Picture 3
3
![Page 8: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/8.jpg)
Picture 4
4
![Page 9: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/9.jpg)
Install the lower arm section. The flexible conduit clamps must first be removed from the robot and re-attached through the Velcro panels in the suit piece. A "gooseneck"
opening near joint 2 allows the conduit to exit the suit piece. A Teflon protective sleeve must also be attached over a wear surface as shown in pictures A and B. Begin the installation by placing the balance unit end between and through the arm and rear
linkage and extend it over the balance unit. Picture sequence 5,6,7 and 8 shows the completed procedure.
A B
![Page 10: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/10.jpg)
Picture 5
![Page 11: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/11.jpg)
Picture 6 – Note…Cut the gum rubber to allow for sync mark to extend out
![Page 12: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/12.jpg)
Picture 7
![Page 13: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/13.jpg)
Picture 8
![Page 14: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/14.jpg)
The remaining piece is the front and rear linkage piece with a hole for the joint 3 cap. The convolutions at each end attach to the two arm pieces with Velcro and snaps.
See pictures 9, 10 and 11.
9
![Page 15: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/15.jpg)
Picture 10
10
![Page 16: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/16.jpg)
Picture 11
11
![Page 17: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/17.jpg)
Fully Assembled Suit on KR180-PA Robot
11
![Page 18: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/18.jpg)
At this point, SLOWLY move robot to watch for interference. The robot will need to move (slowly) with suit installed in order to settle into place.
![Page 19: Roboworld KUKA KR180-PA Robosuit Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022062314/56813291550346895d99262a/html5/thumbnails/19.jpg)
Any questions or concerns on installation, please call Roboworld at 262.339.0584 or 216.798.5839