sabs commercial soc ltd co. reg. no: 2000/013581/07 · pdf filesans 1675 sans 449 the...

CERTIFICATE OF ACCREDITATION

In terms of section 22(2) (b) of the Accreditation for Conformity Assessment, Calibration and Good Laboratory

Practice Act, 2006 (Act 19 of 2006), read with sections 23(1), (2) and (3) of the said Act, I hereby certify that:-

SABS COMMERCIAL SOC LTD Co. Reg. No: 2000/013581/07

Facility Accreditation Number: C07a

is a South African National Accreditation System accredited Certification Body

provided that all SANAS conditions and requirements are complied with

This certificate is valid as per the scope on the accompanying schedule of accreditation,

Annexure “A” bearing the above accreditation number for

PRODUCT CERTIFICATION

The facility is accredited in accordance with the recognised International Standard

ISO GUIDE 65:1996

While this certificate remains valid, the Accredited Facility named above is authorised to use

the relevant SANAS accreditation symbol to issue facility reports and/or certificates

_________________________________________________________________________ Mr R Josias

Chief Executive Officer

Effective Date: 14 February 2012

Certificate Expires: 30 December 2015

ANNEXURE A

S C H E D U L E O F A C C R E D I T A T I O N

Certification Body Accreditation Number: C07a

Physical Address: Pretoria SABS Commercial SOC Ltd 1 Dr Lategan Road Groenkloof Cape Town SABS Commercial SOC Ltd 20 Liesbeeck Parkway Rosebank

Management Signatory

: Mr B Gray

Port Elizabeth

SABS Commercial SOC Ltd

The Acres Office Park

20 Nile Road

Perridgevale Durban SABS Commercial SOC Ltd 15 Garth Road Mayville Postal Address: Private Bag X191 Pretoria 0001

Nominated Representative

: Mr B Gray

Tel Fax Cell E-mail

: +27 (0) 12 428 6736 : +27 (0) 12 428 6703 : +27 (0) 72 865 9858 : [email protected]

Issue No. Date of Issue Expiry Date

: 06 : 15 March 2013 : 30 December 2015

DURBAN SCOPE

SABS Commercial (Pty) Ltd, complies with the accreditation criteria for certification bodies as laid down in ISO/IEC Guide 65 and is authorised to provide Product Certification for the following:

STANDARD PRODUCT

EAC – 3 NACE – DA FOOD PRODUCTS, BEVERAGES AND TOBACCOS

SANS 1675 SANS 449

The manufacture, production, processing and treatment of canned meat products The manufacture of soft drinks and soft drink concentrates

EAC – 4 NACE – DB TEXTILES AND TEXTILES PRODUCTS SANS 1228 SANS 1362 SANS 1387-4 SANS 1394-2 SANS 1401-5

Abrasion resistant polymeric gloves: Lined type Sewing threads Woven cotton and similar apparel fabrics Part 4: Cotton jean and drill fabrics Duvets and pillows Part 2: Synthetic-fibre filled Woven cotton and similar households fabric Part 5: Terry towelling, towels, and other terry weaves articles

SANS 1613 SANS 434

Warp-knitted terry towelling fabrics and articles General protective clothing

Original date of accreditation: 01 May 2002 Page 1 of 21

Field Manager

ANNEXURE A

Certification Body No: C07a Date of Issue: 15 March 2013 Expiry Date: 30 December 2015

DURBAN SCOPE

STANDARD PRODUCT

EAC – 5 NACE – DB TEXTILES AND TEXTILES PRODUCTS

SANS 1068 Coats and jackets (protective, unlined) EAC 12 NACE DG minus 24.4

CHEMICAL PRODUCTS AND FIBRES

SANS 1042 SANS 1218 SANS 1221 SANS 1224 SANS 1225 SANS 1251 SANS 1330 SANS 1344 SANS 1381-4 SANS 1522 SANS 1598 SANS 1755 SANS 1796 SANS 1827 SANS 1828 SANS 1842 SANS 1843 SANS 1853 SANS 235 SANS 237 SANS 307 SANS 308 SANS 309 SANS 317 SANS 342 SANS 548 SANS 555 SANS 731-1 SANS 825

Polymer floor dressings Hydraulic oil (anti-wear type) Detergent skin cleansers Polish stripper Ammoniated liquid detergent cleaner Engine cooling system protectors Waterless hand cleaners Medium duty solvent detergent Materials for thermal insulation of buildings Part 4: Reflective foil laminates (rolls, sheets and sections) Fire extinguishing powders Unleaded petrol Petroleum jelly (petrolatum) Application of durable organic powder coatings for architectural aluminium The safety of water treatment chemicals for use in the food industry Cleaning chemicals for use in the food industry High performance engine lubricating oil for petrol engines (for API Service Category SL) High performance engine lubricating oil for diesel engines (for API Service Category CI-4) Disinfectants and detergent-disinfectants for use in the food industry General purpose pure soap Toilet soap Penetration grade bitumens Cutback bitumen (Metric units) Anionic bitumen road emulsions Industrial bitumens Automotive diesel fuel Cationic bitumen road emulsions Unused and reclaimed mineral insulating oils for transformers and switchgear Road markings Part 1: Single-pack solvent-borne paints Hand dishwashing and light duty detergent (liquid)

EAC – 13 NACE DG 24.4

PHARMACEUTICALS

SANS 1196

SANS 47 SANS 639 SANS 643

Detergent-disinfectants based on organic halogen compounds (other than iodine compounds), such as fluorine, bromine or chlorine Coal-tar type disinfectant liquids (black and white) Detergent-disinfectants based on quaternary ammonium compounds Disinfectants based on stabilized inorganic chlorine compounds


Field Manager

ANNEXURE A

Certification Body No: C07a Date of Issue: 15 March 2013

Expiry Date: 30 December 2015

DURBAN SCOPE

STANDARD PRODUCT

EAC - 14 NACE – DH RUBBER AND PLASTIC PRODUCTS

SANS 11

SANS 11193-1 SANS 1173 SANS 1315 SANS 1366 SANS 1437 SANS 1601 SANS 20109 SANS 4074

Unplasticized poly(vinyl chloride) (PVC-U) components for external rainwater systems Single-use medical examination gloves Part 1: Specification for gloves made from rubber latex or rubber solution General purpose textile-reinforced conveyor belting Polypropylene pressure pipes Steel cord reinforced conveyor belting Footwear soling material and footwear sole and heel components of rubber and plastics Structured wall pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) for buried drainage and sewerage systems Uniform provisions concerning the approval for the production of retreaded pneumatic tyres for commercial vehicles and their trailers Natural latex rubber condoms - Requirements and test methods

SANS 416 SANS 4427 SANS 68 SANS 713 SANS 791 SANS 8773 SANS 952 SANS 952-1 SANS 966-1 SANS 966-2 SANS 967

Chemical resistant gloves Polyethylene (PE) pipes for water supply – Specifications Single-use sterile rubber surgical gloves – Specification Unsaturated polyester (UP) resin systems Unplasticized poly(vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) Polyolefin film for damp- and waterproofing in buildings Polymer film for damp-proofing and waterproofing in buildings Part 1: Monofilament and co-extruded products Components of pressure pipe systems Part 1: Unplasticized poly(vinyl chloride) (PVC-U) pressure pipe systems Components of pressure pipe systems Part 2: Modified poly(vinyl chloride)(PVC-M) pressure pipe systems Unplasticized poly(vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe fitting

SANS 971 SANS 974-1

Conveyor belting - Fire-retardant properties for all construction types Rubber joint rings (non-cellular) Part 1: Joint rings for use in water, sewer and drainage systems

EAC 15 NACE DI minus 26.5.6 NON METALLIC MINERAL PRODUCTS

SANS 141 Glass-reinforced polyester (GRP) laminates EAC 16 NACE Di 26.5,6 CONCRETE, CEMENT, LIME PLASTER etc.

SANS 1058 SANS 1215 SANS 1263-1 SANS 1294 SANS 1381-6 SANS 1491-1 SANS 227 SANS 50197-1 SANS 542 SANS 677 SANS 824 SANS 986

Concrete paving blocks Concrete masonry units Safety and security glazing materials for buildings Part 1: Safety performance of glazing materials under human impact Precast concrete manhole sections and components Materials for thermal insulation of buildings Part 6: Cellulose loose fill thermal insulation material Portland cement extenders Part 1: Ground granulated blast-furnace slag Burnt clay masonry units Cement Part 1: Composition, specifications and conformity criteria for common cements Concrete roofing tiles Concrete non-pressure pipes Lime for soil stabilization Precast reinforced concrete culverts


Field Manager

ANNEXURE A



DURBAN SCOPE

STANDARD PRODUCT

EAC - 17 NACE – DJ 28) FABRICATED METAL PRODUCTS

SANS 1005 SANS 1143 SANS 121 SANS 1219 SANS 1253 SANS 1284 SANS 1397 SANS 1397 SANS 1475-1 SANS 1475-2 SANS 1567 SANS 1700-7-1 SANS 1700-7-3 SANS 1910 SANS 193 SANS 29 SANS 4 SANS 407 SANS 455 SANS 50354 SANS 50355 SANS 50358 SANS 50361 SANS 50795 SANS 543 SANS 675 SANS 727 SANS 809 SANS 916 SANS 920 SANS 935 SANS 999

Innerspring mattresses Mushroom- and countersunk-head bolts and nuts Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods Hand hacksaw blades Fire-doors and fire-shutters Bow-saw frames and blades Industrial safety helmets Industrial safety helmets The production of reconditioned fire-fighting equipment Part 1: Portable and wheeled (mobile) rechargeable fire extinguishers The production of reconditioned fire-fighting equipment Part 2: Fire hose reels and above-ground hydrants Portable rechargeable fire extinguishers - CO2 type extinguishers Fasteners Part 7: External drive hexagon bolts and screws Section 1: Hexagon head bolts - Product grades A and B Fasteners Part 7: External drive hexagon bolts and screws Section 3: Hexagon head bolts - Product grade C Portable refillable fire extinguishers Fire-dampers Articles made of precious metals Locks, latches, and associated furniture for doors (Domestic Type) Austenitic manganese steel castings Covered electrodes for the manual arc welding of carbon and carbon manganese steels Personal protective equipment against falls from a height - Lanyards Personal protective equipment against falls from a height - Energy absorbers Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards Personal protective equipment against falls from a height - Full body harnesses Protection against falls from a height - Anchor devices - Requirements and testing Fire hose reels Zinc-coated fencing wire Windows and doors made from rolled mild steel sections Industrial body belts Fishbolts and nuts for light rails Steel bars for concrete reinforcement Hot-dip (galvanized) zinc coatings on steel wire Anodized coatings on aluminium (for architectural applications)

EAC – 19 NACE – DL minus 32.1 & DK 29.7)

ELECTRICAL AND OPTICAL EQUIPMENT & DOMESTIC APPLIANCES

SANS 1339 SANS 1376-3 SANS 1464-22 SANS 1507-2 SANS 1507-3 SANS 151 SANS 1524-1 SANS 1561-1 SANS 1973-1 SANS 1973-3 SANS 60065

Electric cables - Cross-linked polyethylene (XLPE) insulated cables for rated voltages 3,8/6,6 kV to 19/33 kV Lights for motor vehicles Part 3: Secondary lights Safety of luminaires Part 22: Luminaires for emergency lighting Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to 1 900/3 300 V) Part 2: Wiring cables Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to 1 900/3 300 V) Part 3: PVC Distribution cables Fixed electric storage water heaters Electricity payment systems Part 1: Prepayment meters Rewound and refurbished rotating electrical machines Part 1: Low-voltage three-phase induction motors Low-voltage switchgear and controlgear Assemblies Part1: Type tested Assemblies Low-voltage switchgear and controlgear Assemblies Part1: Safety of Assemblies Audio, video and similar electronic apparatus - Safety requirements


Field Manager

ANNEXURE A



DURBAN SCOPE

STANDARD PRODUCT

(EAC – 19 NACE – DL minus 32.1 & DK 29.7)

ELECTRICAL AND OPTICAL EQUIPMENT & DOMESTIC APPLIANCES

SANS 60079-0 SANS 60079-1 SANS 60079-11 SANS 60079-15 SANS 60335-1 SANS 60335-2-24 SANS 60335-2-84 SANS 60598-1 SANS 60598-2-1 SANS 60598-2-5 SANS 60614-1 SANS 61058-1 SANS 61241-0 SANS 61084-2-1 SANS 61241-1 SANS 868-1-1

Electrical apparatus for explosive gas atmospheres Part 0: General requirements Electrical apparatus for explosive gas atmospheres Part 1: Flameproof enclosures "d" Explosive atmospheres Part 11: Equipment protection by intrinsic safety "i" Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and marking of type of protection "n" electrical apparatus Household and similar electrical appliances - Safety Part 1: General requirements Household and similar electrical appliances - Safety Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice-makers Household and similar electrical appliances – Safety Part 2-84: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant unit or compressor Luminaires Part 1: General requirements and tests Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires Luminaires Part 2-5: Particular requirements - Floodlights Conduits for electrical installations - Specification Part 1: General requirements Switches for appliances Part 1: General requirements Electrical apparatus for use in the presence of combustible dust Part 0: General requirements Cable trunking and ducting systems for electrical installations Part 2: Particular requirements Section 1: Cable trunking and ducting systems intended for mounting on walls or ceilings Electrical apparatus for use in the presence of combustible dust Part 1: Protection by enclosures "tD" Compression-ignition engine systems and machines powered by such engine systems, for use in mines and plants with explosive gas atmospheres or explosive dust atmospheres or both Part 1-1:Hazardous locations in underground mines - Basic explosion protected

EAC - 22 NACE DM34,35.2,5

Other transport equipment

SANS 1116-2 SANS 1116-4 SANS 1186-1 SANS 1186-5 SANS 1193 SANS 1329-4

Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium) Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics) Symbolic safety signs Part 1: Standard signs and general requirements Symbolic safety signs Part 5: Photoluminescent signs Safety glass for vehicles - Toughened safety glass for vehicles Retro-reflective and fluorescent warning signs for road vehicles Part 4: Retro-reflective chevron signs Ball type couplings and towing brackets for towing caravans and light trailers Part 1: Towing brackets and integrated towing devices


Field Manager

ANNEXURE A



CAPE TOWN SCOPE

STANDARD PRODUCT

(EAC – 3 NACE – DA) FOOD PRODUCTS,BEVERAGES AND TOBACCO

SANS 1657

Bottled water of subterranean origin

SANS 449 The manufacture of soft drinks and soft drink concentrates SANS 587

Canned fish, canned marine molluscs and canned crustaceans and products derived therefrom

(EAC – 4 NACE DB) TEXTILES AND TEXTILE PRODUCTS

SANS 1118-3

School clothing Part 3: Trousers and shorts

SANS 1118-4 School clothing Part 4: Shirts SANS 1118-6 School clothing Part 6: Dresses, tunics and gyms SANS 1118-7 School clothing Part 7: Girls' slacks and skirts SANS 1362 Sewing threads SANS 1703 Shade netting SANS 434 Boiler suits and workwear suits SANS 985 Polyester-and-wool uniform fabrics (EAC – 5 NACE DC) LEATHER AND LEATHER PRODUCTS

SANS 421 The production of men's shoes (Goodyear welted with stitched or stuck-on outer soles)

(EAC – 12 NACE DG) CHEMICALS, CHEMICAL PRODUCTS AND FIBRES

SANS 1042 Polymer floor dressings SANS 1044 Industrial laundry detergents SANS 1216 Solvent-emulsion degreasers SANS 1224 Polish stripper SANS 1225 Ammoniated liquid detergent cleaner SANS 1330 Waterless hand cleaners SANS 1344 Medium duty solvent detergent SANS 1586 SANS 1598 SANS 1796 SANS 1827 SANS 1828 SANS 1853 SANS 309 SANS 342

Emulsion paints Unleaded petrol Application of durable organic powder coatings for architectural aluminium The safety of water treatment chemicals for use in the food industry Cleaning chemicals for use in the food industry Disinfectants and detergent-disinfectants for use in the food industry Anionic bitumen road emulsions Automotive diesel fuel

SANS 515 SANS 548 SANS 630 SANS 731-1 SANS 825

Decorative paint for interior use Cationic bitumen road emulsions Decorative high gloss enamel paints Road markings Part 1: Single-pack solvent-borne paints Hand dishwashing and light duty detergent (liquid)


Field Manager

ANNEXURE A



CAPE TOWN SCOPE

STANDARD PRODUCT

(EAC – 13 NACE – DG) PHARMACEUTICALS

SANS 116 SANS 1196 SANS 296 SANS 47 SANS 636 SANS 639

Liquid antiseptics containing substituted phenolics Detergent-disinfectants based on organic halogen compounds (other than iodine compounds), such as fluorine, bromine or chlorine Sodium hypochlorite solutions Coal-tar type disinfectant liquids (black and white) Disinfectants based on quaternary ammonium compounds Detergent-disinfectants based on quaternary ammonium compounds

(EAC 14 NACE DH) RUBBER AND PLASTIC PRODUCTS

SANS 11 SANS 1291-2 SANS 1494 SANS 1601 SANS 20109

Unplasticized poly(vinyl chloride) (PVC-U) components for external rainwater systems Flexible polyurethane foam sleeping mats and mattresses Part 2: Foam mattresses for domestic and hotel use

Mobile refuse bins Structured wall pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) for buried drainage and sewerage systems Uniform provisions concerning the approval for the production of retreaded pneumatic tyres for commercial vehicles and their trailers

SANS 4074 Natural latex rubber condoms - Requirements and test methods SANS 4427 Polyethylene (PE) pipes for water supply - Specifications SANS 791 Unplasticized poly(vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings

SANS 966-1 Components of pressure pipe systems Part 1: Unplasticized poly(vinyl chloride)

(PVC-U) pressure pipe systems

SANS 966-2 Components of pressure pipe systems Part 2: Modified poly(vinyl chloride) (PVC-

M) pressure pipe systems

SANS 967 Unplasticized poly(vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe

fittings

(EAC – 16 NACE DI) CONCRETE,CEMENT, LIME, PLASTER ETC

SANS 1058 SANS 1215 SANS 1263-1 SANS 1294 SANS 1381-6 SANS 1575

Concrete paving blocks Concrete masonry units Safety and security glazing materials for buildings Part 1: Safety performance of glazing materials under human impact Precast concrete manhole sections and components Materials for thermal insulation of buildings Part 6: Cellulose loose fill thermal insulation material Burnt clay paving units

SANS 1882 SANS 227 SANS 470 SANS 50197-1 SANS 523 SANS 542 SANS 676 SANS 677 SANS 824 SANS 986

Polymer concrete surface boxes, manhole and inspection covers, gully gratings and frames Burnt clay masonry units Concrete poles for telephone, power and lighting purposes Cement Part 1: Composition, specifications and conformity criteria for common cements Limes for use in building Concrete roofing tiles Reinforced concrete pressure pipes Concrete non-pressure pipes Lime for soil stabilization Precast reinforced concrete culverts


Field Manager

ANNEXURE A



CAPE TOWN SCOPE

STANDARD PRODUCT (EAC - 17 NACE DJ BASIC METAL AND FABRICATED METAL PRODUCTS

SANS 1005 SANS 1062 SANS 121 SANS 1219 SANS 1475-1 SANS 1475-2

Innerspring mattresses Pressure and vacuum gauges Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods Hand hacksaw blades The production of reconditioned fire-fighting equipment Part 1: Portable and wheeled (mobile) rechargeable fire extinguishers The production of reconditioned fire-fighting equipment Part 2: Fire hose reels and above-ground hydrants

SANS 193 SANS 4 SANS 543 SANS 751 SANS 920 SANS 949 SANS 953-1 SANS 999

Fire-dampers Locks, latches, and associated furniture for doors (Domestic Type) Fire hose reels Burglar-resistant safes Steel bars for concrete reinforcement Strongroom and vault doors Storage of firearms and ammunition Part 1: Safes Anodized coatings on aluminium (for architectural applications)

(EAC – 19 NACE DC) ELECTRICAL AND OPTICAL EQUIPMENT/ELECTRONIC COMPONENTS

SANS 1020 SANS 1507-3 SANS 151 SANS 1524-1 SANS 181 SANS 186 SANS 514 SANS 537

Power-operated dispensing devices for flammable liquid fuels Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to 1 900/3 300 V) Part 3: PVC Distribution cables Fixed electric storage water heaters Electricity payment systems Part 1: Prepayment meters Thermostats for electric storage water heaters Energy regulators for electric heating units Immersion heaters for electric storage water heaters Oven thermostats for electric stoves

SANS 60079-0 SANS 60079-1 SANS 60079-15 SANS 60335-2-30 SANS 60598-2-1 SANS 60598-2-2 SANS 60614-2-2

Explosive atmospheres Part 0: Equipment - General requirements Explosive atmospheres Part 1: Equipment protection by flameproof enclosures "d" Explosive atmospheres Part 15: Equipment protection by type of protection "n" Household and similar electrical appliances - Safety Part 2-30: Particular requirements for room heaters Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires Luminaires Part 2: Particular requirements Section 2: Recessed luminaires Specification for conduits for electrical installations Part 2: Particular specification for conduits Section 2: Rigid plain conduits of insulating materials

SANS 61643-1 SANS 62052-11 SANS 755 SANS 780

Low-voltage surge protective devices Part 1: Surge protective devices connected to low-voltage power distribution systems - Requirements and tests Electricity metering equipment (a.c.) - General requirements, tests and test conditions Part 11: Metering equipment Mineral-insulated metal-sheathed air-heating units for appliances Distribution transformers


Field Manager

ANNEXURE A



CAPE TOWN SCOPE

STANDARD PRODUCT

(EAC – 22 NACE DM) OTHER TRANSPORT EQUIPMENT

SANS 1080 Restraining devices (safety belts) for occupants of adult build in motor vehicles

(revised requirements) SANS 1116-2 Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium) SANS 1116-4 Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics) SANS 1186-1 Symbolic safety signs Part 1: Standard signs and general requirements SANS 1186-5 Symbolic safety signs Part 5: Photoluminescent signs SANS 1192 Laminated safety glass for vehicles

SANS 1193

Toughened safety glass for vehicles


Field Manager

ANNEXURE A


PRETORIA SCOPE

STANDARD PRODUCT

(EAC – 3 NACE DC) FOOD PRODUCTS, BEVERAGES AND TOBACCOS

SANS 1657 SANS 1657 SANS 1678 SANS 1679 SANS 1862 SANS 449 SANS 49

Bottled natural water Bottled natural water of subterranean origin Sterilized milk Pasteurized milk Packaged water other than natural mineral water The manufacture of soft drinks and soft drink concentrates Edible gelatin


SANS 1703 SANS 434 SANS 94-1 SANS 94-2

Shade netting Boiler suits and workwear suits Textile slings - Safety Part 1: Flat woven webbing slings, made of man-made fibres, for general purpose use Textile slings - Safety Part 2: Roundslings made of man-made fibres for general purpose use


SANS 20345 SANS 421 SANS 741 SANS 942

Personal protective equipment - Safety footwear The production of men's shoes (Goodyear welted with stitched or stuck-on outer soles) Industrial boots (including safety boots) with direct-vulcanized soles and heels Children's, youths', and maids' school shoes with direct injection-moulded soles and heels

(EAC – 6 NACE DD) WOOD AND WOOD PRODUCTS

SANS 1783-1 SANS 1783-2 SANS 1783-3 SANS 1783-4 SANS 1900 SANS 457-2 SANS 457-3 SANS 545 SANS 660 SANS 753 SANS 754 SANS 929

Sawn softwood timber Part 1: General requirements Sawn softwood timber Part 2: Stress-graded structural timber and timber for frame wall construction Sawn softwood timber Part 3: Industrial timber Sawn softwood timber Part 4: Brandering and battens Monoplanar prefabricated timber roof trusses (nail-plated) Wooden poles, droppers, guardrail posts and spacer blocks Part 2: Softwood species Wooden poles, droppers, guardrail posts and spacer blocks Part 3: Hardwood species Wooden doors Classroom furniture Pine poles, cross-arms and spacers for power distribution, telephone systems and street lighting Eucalyptus poles, cross-arms and spacers for power distribution and communications systems Plywood and composite board


Field Manager

ANNEXURE A


PRETORIA SCOPE

STANDARD PRODUCT

(EAC - 10 NACE – DF 23.1, 2) MANUFACTURER OF COKE AND REFINED PETROLEUM PRODUCTS

SANS 616

Wood-preserving creosote mixtures and coal-tar mixtures

(EAC – 12 NACE – DG minus 24.4) CHEMICAL PRODUCTS AND FIBRES

SANS 630 Decorative high gloss enamel paints SANS 650 Laundry detergent (for use in non-automatic domestic washing machines)

SANS 651 Low-foam laundry detergent (for use in automatic and non-automatic domestic

washing machines) SANS 680 Glazing putty for wooden and metal window frames SANS 681 Undercoats for paints SANS 731-1 Road markings Part 1: Single-pack solvent-borne paints SANS 825 Hand dishwashing and light duty detergent (liquid) SANS 892 General purpose detergent (beads, granules and powders) SANS 940 Emulsion roof paint (EAC - 13 NACE – DG 24.4 PHARMACEUTICALS

SANS 636 Disinfectants based on quaternary ammonium compounds SANS 639 Detergent-disinfectants based on quaternary ammonium compounds SANS 643 Disinfectants based on stabilized inorganic chlorine compounds

(EAC – 14 NACE – DH) RUBBER AND PLASTIC PRODUCTS

SANS 786 Flexible vinyl flooring SANS 791 Unplasticized poly(vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings SANS 808 Cable glands for use on flameproof enclosures (Ex d)

SANS 950 Unplasticized polyvinyl chloride rigid conduit and fittings for use in electrical

installations SANS 952 Polyolefin film for damp- and waterproofing in buildings

SANS 966-1 Components of pressure pipe systems Part 1: Unplasticized poly(vinyl chloride) (PVC-

U) pressure pipe systems

SANS 966-2 Components of pressure pipe systems Part 2: Modified poly(vinyl chloride) (PVC-M)

pressure pipe systems SANS 967 Unplasticized poly(vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe fittings SANS 971 Fire-retardant textile-reinforced conveyor belting (for use in fiery mines)


Field Manager

ANNEXURE A



PRETORIA SCOPE

STANDARD PRODUCT

(EAC – 15 NACE – Di minus 26.5,6) NON METALLIC MINERAL PRODUCTS

SANS 141 Glass-reinforced polyester (GRP) laminates

SANS 15875-5

Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) Part 5: Fitness for purpose of the system

SANS 1748-1

Glass-fibre-reinforced thermosetting plastics (GRP) pipes Part 1: Pipes for water supply, sewerage and drainage

SANS 1749

Glass-reinforced polyester (GRP) poles

(EAC – 16 NACE – Di 26.5 & 6) CONCRETE, CEMENT, LIME, PLASTER ETC.

SANS 1022 Metal roofing tiles SANS 1058 Concrete paving blocks SANS 1215 Concrete masonry units

SANS 1263-1 Safety and security glazing materials for buildings Part 1: Safety performance of glazing materials under human impact

SANS 1263-2 Safety and security glazing materials for buildings Part 2: Burglar-resistant and vandal-resistant glazing materials

SANS 1263-3 Safety and security glazing materials for buildings Part 3: Bullet-resistant glazing materials

SANS 1294 Precast concrete manhole sections and components SANS 1381-1 Materials for thermal insulation of buildings Part 1: Fibre thermal insulation mats SANS 1491-1 Portland cement extenders Part 1: Ground granulated blastfurnace slag SANS 1491-2 Portland cement extenders Part 2: Fly ash SANS 1575 Burnt clay paving units

SANS 15876-1 Plastics piping systems for hot and cold water installations - Polybutylene (PB) Part 1: General

SANS 1879 Precast concrete suspended slabs

SANS 1882 Polymer concrete surface boxes, manhole and inspection covers, gully gratings and frames

SANS 227 Burnt clay masonry units SANS 470 Concrete poles for telephone, power and lighting purposes

SANS 50197-1 Cement Part 1: Composition, specifications and conformity criteria for common cements

SANS 50413-1 Masonry cement Part 1: Composition, specifications and conformity criteria SANS 508 Concrete retaining blocks SANS 523 Limes for use in building SANS 540-1 Fibreboard products Part 1: Uncoated fibreboard SANS 540-2 Fibreboard products Part 2: Coated fibreboard SANS 542 Concrete roofing tiles SANS 676 Reinforced concrete pressure pipes SANS 677 Concrete non-pressure pipes SANS 685 Fibre-cement sheets (flat and profiled) SANS 803 Fibre-cement boards

SANS 819 Fibre-cement pipes, couplings and fittings for sewerage, drainage and low-pressure irrigation

SANS 824 Lime for soil stabilization SANS 927 Precast concrete kerbs, edgings and channels SANS 986 Precast reinforced concrete culverts

SANS 9933 Products in fibre-reinforced cement - Long corrugated or asymmetrical section sheets and fittings for roofing and cladding


Field Manager

ANNEXURE A



PRETORIA SCOPE

STANDARD PRODUCT

(EAC – 17 NACE – DJ27,28) BASIC METALS AND FABRICATED METAL PRODUCTS

SANS 1005 Innerspring mattresses SANS 101 White metal designated WM 6 SANS 10131 Above-ground storage tanks for petroleum products SANS 102 White metal designated WM 15 SANS 1024 Welded steel fabric for reinforcement of concrete

SANS 10244-2 Steel wire and wire products - Non-ferrous metallic coatings on steel wire Part 2: Zinc

and zinc alloy coatings SANS 1026 Bench vices for metal work (Metric units) SANS 103 White metal designated WM 30 SANS 1034 Grey iron castings SANS 104 White metal designated WM 40 SANS 1056-2 Ballvalves Part 2: Heavy duty valves (not fire-safe) SANS 1056-3 Ballvalves Part 3: Light duty valves (not fire-safe) SANS 106 White metal designated WM 66 SANS 1060 Wheelchairs (folding type) SANS 1062 Pressure and vacuum gauges SANS 1063 Earth rods, couplers and connections SANS 1067-1 Copper-based fittings for copper tubes Part 1: Compression fittings SANS 1067-2 Copper-based fittings for copper tubes Part 2: Capillary solder fittings SANS 107 White metal designated WM 72 SANS 108 White metal designated WM 80 SANS 109 White metal designated WM 84 SANS 1115 Cast iron gratings for gullies and stormwater drains SANS 1120 Pliers and nippers

SANS 1128-1 Firefighting equipment Part 1: Components of underground and above-ground hydrant

systems SANS 1151 Portable rechargeable fire extinguishers - Halogenated hydrocarbon type extinguishers SANS 11601 Wheeled fire extinguishers - Performance and construction SANS 1172 Files and rasps SANS 1182 Light gauge welded steel pipes

SANS 121 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and

test methods SANS 12277 Mountaineering equipment - Harnesses - Safety requirements and test methods SANS 124 White metal designated WM 90 SANS 1240 Automatic shut-off flush valves for water closets and urinals SANS 1253 Fire-doors and fire-shutters

SANS 1313-1 Conveyor belt idlers Part 1: Troughed belt conveyor idlers (metallic and non-metallic)

for belt speeds of up to 5,0 m/s SANS 1350 Guardrails for roads (W-section) SANS 137 Resin cored solders (non-corrosive) SANS 138 Resin cored solders (highly activated) SANS 1397 Industrial safety helmets SANS 14 Malleable cast iron fittings threaded to ISO 7-1 SANS 1407 Anodized coatings on aluminium (for general applications) SANS 1409 Outlet sockets and probes for medical (gas and vacuum) services used in hospitals SANS 1431 Weldable structural steels

SANS 14341 Welding consumables - Wire electrodes and deposits for gas shielded metal arc

welding of non alloy and fine grain steels - Classification SANS 1451-2 Hearing protectors Part 2: Ear-plugs

SANS 14520-1 Gaseous fire-extinguishing systems - Physical properties and system design Part 1:

General requirements


Field Manager

ANNEXURE A



PRETORIA SCOPE

STANDARD PRODUCT



IG-55 extinguishant


HFC 227ea extinguishant SANS 1453 Copper tubes for medical gas and vacuum services

SANS 1475-1 The production of reconditioned fire-fighting equipment Part 1: Portable and wheeled

(mobile) rechargeable fire extinguishers

SANS 1475-2 The production of reconditioned fire-fighting equipment Part 2: Fire hose reels and

above-ground hydrants SANS 1480 Single control mixer taps SANS 1509 Flush valves for WC flushing cisterns SANS 1532 Vent valves for drainage installations SANS 1533 Padlocks

SANS 1535 Glass-reinforced polyester-coated steel tanks for the underground storage of

hydrocarbons and oxygenated solvents and intended for burial horizontally SANS 1539 Appliances operating on liquefied petroleum gas - Safety aspects SANS 1551-1 Check valves (flanged and wafer types) Part 1: PN series SANS 1567 Portable rechargeable fire extinguishers - CO2 type extinguishers

SANS 15876-2 Plastics piping systems for hot and cold water installations - Polybutylene (PB) Part 2:

Pipes SANS 1592 Short-link steel chain (close-tolerance) for lifting appliances SANS 1594 Manually operated chain blocks

SANS 1595 Forged steel lifting hooks for use with steel chains of strength grade M(4), P(5), S(6),

T(8) and V(10) SANS 1636 Manually operated chain lever hoists SANS 1655 Welding of thermoplastics - Welding rods, fillers and solvents SANS 1808-16 Water supply and distribution system components Part 16: Drinking fountains

SANS 1808-2 Water supply and distribution system components Part 2: Metallic compression type

pipe couplings

SANS 1808-35 Water supply and distribution system components Part 35: Electronically operated

taps and valves SANS 1808-44 Water supply and distribution system components Part 44: Pipe saddles SANS 1808-5 Water supply and distribution system components Part 5: Flexible connectors

SANS 1808-53 Water supply and distribution system components Part 53: Drain cocks for hot-water

storage containers SANS 1808-66 Water supply and distribution system components Part 66: Demand type water taps

SANS 1808-9 Water supply and distribution system components Part 9: Metering taps and valves

(metallic bodies) SANS 1845 Prefinished sheet metal products for interior and exterior building applications SANS 1849 Butterfly valves for general purposes SANS 1849 Butterfly valves for general purposes SANS 189 Short-link steel chain (medium-tolerance) for lifting purposes SANS 1906 Non-pressure paraffin stoves and heaters SANS 191 Cast steel gate valves SANS 1910 Portable refillable fire extinguishers SANS 193 Fire-dampers

SANS 198 Functional-control valves and safety valves for domestic hot and cold water supply

systems SANS 199 Shut-off valves for refillable liquefied petroleum gas cylinders SANS 2081 Metallic coatings - Electroplated coatings of zinc on iron or steel SANS 226 Water taps (metallic bodies) SANS 24 Soft solders


Field Manager

ANNEXURE A



PRETORIA SCOPE

STANDARD PRODUCT


SANS 2503

Gas welding equipment - Pressure regulators for gas cylinders used in welding, cutting and allied processes up to 300 bar

SANS 251 Long-link and extra-long-link medium tolerance steel chains for general purposes

SANS 2560 Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and

fine grain steels - Classification SANS 284 Spades and shovels

SANS 29 Articles made of precious metals

SANS 32 Internal and/or external protective coatings for steel tubes - Specification for hot dip

galvanized coatings applied in automatic plants SANS 3310-1 Test sieves - Technical requirements and testing Part 1: Test sieves of metal wire cloth

SANS 3310-2 Test sieves - Technical requirements and testing Part 2: Test sieves of perforated metal

plate SANS 343 Steel bedside lockers

SANS 3581 Welding consumables - Covered electrodes for manual metal arc welding of stainless and

heat-resisting steels - Classification SANS 387 Hammer heads and hand hammers SANS 39 Small medical gas cylinders - Pin-index yoke-type valve connections SANS 390 Forks and rakes SANS 4 Locks, latches, and associated furniture for doors (Domestic Type) SANS 407 Austenitic manganese steel castings SANS 455 Covered electrodes for the manual arc welding of carbon and carbon manganese steels SANS 460 Plain-ended solid drawn copper tubes for potable water SANS 4706 Refillable welded steel gas cylinders SANS 4778 Chain slings of welded construction - Grades M(4), S(6) and T(8) SANS 497 Glazed ceramic sanitaryware

SANS 50124 Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements,

type testing, marking, quality control

SANS 50149 Respiratory protective devices - Filtering half masks to protect against particles -

Requirements, testing, marking

SANS 50353-1 Personal protective equipment against falls from a height - Guided type fall arresters

including a rigid anchor line SANS 50354 Personal protective equipment against falls from a height - Lanyards SANS 50355 Personal protective equipment against falls from a height - Energy absorbers

SANS 50358 Personal protective equipment for work positioning and prevention of falls from a height -

Belts for work positioning and restraint and work positioning lanyards SANS 50361 Personal protective equipment against falls from a height - Full body harnesses

SANS 50440 Welding consumables - Wire electrodes and deposits for gas shielded metal arc welding

of non alloy and fine grain steels - Classification SANS 50566 Mountaineering equipment - Slings - Safety requirements and test methods SANS 50730-1 Gas welding equipment - Safety devices Part 1: Incorporating a flame (flashback) arrestor SANS 50795 Protection against falls from a height - Anchor devices - Requirements and testing SANS 50813 Personal protective equipment for prevention of falls from a height - Sit harnesses SANS 51317-1 Road restraint systems Part 1: Terminology and general criteria for test methods

SANS 51317-2 Road restraint systems Part 2: Performance classes, impact test acceptance criteria and

test methods for safety barriers SANS 521 Hospital beds and cots SANS 52842 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods SANS 53811 Sherardizing - Zinc diffusion coatings on ferrous products – Specification


Field Manager

ANNEXURE A

Certification Body No: C07a

Date of Issue: 15 March 2013 Expiry Date: 30 December 2015

PRETORIA SCOPE

STANDARD PRODUCT

(EAC – 18 NACE –) MACHINERY AND EQUIPMENT

SANS 15876-3

Plastics piping systems for hot and cold water installations - Polybutylene (PB) Part 3: Fittings

(EAC – 19 NACE – DL MINUS

32.1 & DK 29.7) ELECTRICAL AND OPTICAL EQUIPMENT, DOMESTIC APPLIANCES

SANS 1213 Electric light dimmers (Metric units) SANS 1239 Power-operated dispensing devices for flammable liquid fuels SANS 1266 Mechanical cable glands SANS 1339 Plugs, socket-outlets and couplers for industrial purposes SANS 1376-2 Ballasts for discharge lamps (excluding tubular fluorescent lamps)

SANS 1376-3 Electric cables - Cross-linked polyethylene (XLPE) insulated cables for rated voltages 3,8/6,6 kV to

19/33 kV SANS 1418-1 Lights for motor vehicles Part 2: Headlights SANS 1418-2 Lights for motor vehicles Part 3: Secondary lights SANS 1438-3 Aerial bundled conductor systems Part 1: Cores SANS 1464-22 Aerial bundled conductor systems Part 2: Assembled insulated conductor bundles SANS 1489 Helmet light assemblies for miners Part 3: Cables

SANS 1507-1

Safety of luminaires Part 22: Luminaires for emergency lighting

SANS 1507-2 Flameproof restrained and bolted type plugs and sockets

SANS 1507-3 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to 1 900/3

300 V) Part 1: General


300 V) Part 2: Wiring cables


300 V) Part 3: PVC distribution cables


300 V) Part 4: XLPE distribution cables

SANS 151 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to 1 900/3

300 V) Part 5: Halogen-free distribution cables


300 V) Part 6: Service cables SANS 1520-2 Fixed electric storage water heaters

SANS 1524-1 Flexible electric trailing cables for use in mines Part 1: Low-voltage (640/1 100 V and 1 900/3 300

V) cables SANS 1561-1 Flexible electric trailing cables for use in mines Part 2: High-voltage (3,8/6,6 kV to 19/33 kV) cables SANS 1574-1 Electricity payment systems Part 1: Prepayment meters

SANS 1574-3 Rewound and refurbished rotating electrical machines Part 1: Low-voltage three-phase induction

motors SANS 1574-4 Electric flexible cores, cords and cables with solid extruded dielectric insulation Part 1: General

SANS 1574-5 Electric flexible cores, cords and cables with solid extruded dielectric insulation Part 3: PVC-

insulated cores and cables

SANS 1576 Electric flexible cables with solid extruded dielectric insulation Part 4: Rubber-insulated cores and

cords

SANS 15876-5 Electric flexible cables with solid extruded dielectric insulation Part 5: Rubber-insulated cores and

cables

SANS 164-0 Electric cables - Single core arc welding cable


Field Manager

ANNEXURE A Certification Body No: C07a


PRETORIA SCOPE

STANDARD PRODUCT

(EAC – 19 NACE – DL MINUS 32.1 & DK 29.7)

ELECTRICAL AND OPTICAL EQUIPMENT, DOMESTIC APPLIANCES

SANS 60335-2-7 Household and similar electrical appliances - Safety Part 2-7: Particular requirements for washing

machines

SANS 60335-2-75 Household and similar electrical appliances - Safety Part 2-75: Particular requirements for commercial

dispensing appliances and vending machines SANS 60335-2-80 Safety of household and similar electrical appliances Part 2-80: Particular requirements for fans SANS 60432-3 Incandescent lamps - Safety specifications Part 3: Tungsten-halogen lamps (non-vehicle) SANS 60529 Degrees of protection provided by enclosures (IP Code) SANS 60598-2-1 Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires SANS 60598-2-2 Luminaires Part 2: Particular requirements Section 2: Recessed luminaires SANS 60598-2-20 Luminaires Part 2-20: Particular requirements - Lighting chains SANS 60598-2-23 Luminaires Part 2-23: Particular requirements - Extra low voltage lighting systems for filament lamps

SANS 60598-2-25 Luminaires Part 2-25: Particular requirements - Luminaires for use in clinical areas of hospitals and

health care buildings SANS 60598-2-3 Luminaires Part 2-3: Particular requirements - Luminaires for road and street lighting SANS 60598-2-4 Luminaires Part 2: Particular requirements Section 4: Portable general purpose luminaires SANS 60598-2-5 Luminaires Part 2-5: Particular requirements - Floodlights

SANS 60598-2-6 Luminaires Part 2: Particular requirements Section 6: Luminaires with built-in transformers or convertors

for filament lamps SANS 60598-2-7 Luminaires Part 2: Particular requirements Section 7: Portable luminaires for garden use SANS 60598-2-8 Luminaires Part 2-8: Particular requirements - Handlamps SANS 60614-1 Conduits for electrical installations - Specification Part 1: General requirements

SANS 60614-2-2 Specification for conduits for electrical installations Part 2: Particular specification for conduits Section 2:

Rigid plain conduits of insulating materials SANS 60669-1 Switches for household and similar fixed-electrical installations Part 1: General requirements SANS 60669-2-1 Switches for household and similar fixed electrical installations Part 2-1: Particular requirements -

Electronic switches SANS 60670-1 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations

Part 1: General requirements SANS 60670-24 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations

Part 24: Particular requirements for enclosures for housing protective devices and similar power consuming devices

SANS 60730-2-9 Automatic electrical controls for household and similar use Part 2-9: Particular requirements for temperature sensing controls

SANS 60794-4 Optical fibre cables Part 4: Sectional specification - Aerial optical cables along electrical power lines SANS 60799 Electrical accessories - Cord sets and interconnection cord sets

SANS 60884-2-5 Plugs and socket-outlets for household and similar purposes Part 2-5: Particular requirements for

adaptors SANS 60901 Single-capped fluorescent lamps - Performance specifications

SANS 60947-3 Low-voltage switchgear and controlgear Part 3: Switches, disconnectors, switch-disconnectors and fuse-

combination units SANS 60968 Self-ballasted lamps for general lighting services - Safety requirements SANS 60969 Self-ballasted lamps for general lighting services - Performance requirements

SANS 61048 Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp circuits -

General and safety requirements SANS 61084-1 Cable trunking and ducting systems for electrical installations Part 1: General requirements

SANS 61084-2-1 Cable trunking and ducting systems for electrical installations Part 2: Particular requirements Section 1:

Cable trunking and ducting systems intended for mounting on walls or ceilings SANS 61199 Single-capped fluorescent lamps - Safety specifications SANS 61241-0 Electrical apparatus for use in the presence of combustible dust Part 0: General requirements SANS 61241-1 Electrical apparatus for use in the presence of combustible dust Part 1: Protection by enclosures "tD" SANS 61243-1 Live working - Voltage detectors Part 1: Capacitive type to be used for voltages exceeding 1 kV a.c. SANS 61347-2-1 Lamp controlgear Part 2-1: Particular requirements for starting devices (other than glow starters)

SANS 61347-2-2 Lamp controlgear Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down

convertors for filament lamps

SANS 61347-2-3 Lamp controlgear Part 2-3: Particular requirements for a.c supplied electronic ballasts for fluorescent

lamps SANS 61347-2-8 Lamp controlgear Part 2-8: Particular requirements for ballasts for fluorescent lamps

SANS 61347-2-9 Lamp controlgear Part 2-9: Particular requirements for ballasts for discharge lamps (excluding

fluorescent lamps) SANS 61481 Live working - Portable phase comparators for use on voltages from 1 kV to 36 kV a.c.

SANS 61558-2-5 Safety of power transformers, power supply units and similar Part 2-5: Particular requirements for shaver

transformers and shaver supply units

SANS 61558-2-6 Safety of power transformers, power supply units and similar Part 2-6: Particular requirements for safety

isolating transformers for general use

Original date of accreditation: 01 May 2002 of 21

Field Manager

ANNEXURE A

Certification Body No: C07a


PRETORIA SCOPE

STANDARD PRODUCT



SANS 61643-1

Low-voltage surge protective devices Part 1: Surge protective devices connected to low-voltage power distribution systems - Requirements and tests

SANS 767-1 Earth leakage protection units Part 1: Fixed earth leakage protection circuit-breakers SANS 780 Distribution transformers

SANS 868-1-1 Compression-ignition engine systems and machines powered by such engine systems, for use in mines

and plants with explosive gas atmospheres or explosive dust atmospheres or both Part 1-1:Hazardous locations in underground mines - Basic explosion protected

SANS 868-1-3 Compression-ignition engine systems and machines powered by such engine systems, for use in mines

and plants with explosive gas atmospheres or explosive dust atmospheres or both Part 1-3: Hazardous locations in underground mines - Machines

SANS 890-1 Ballasts for fluorescent lamps Part 1: Ballasts for lamps for operation with starters (class A lamps)

SANS 97 Electric cables - Impregnated paper-insulated metal-sheathed cables for rated voltages 3,3/3,3kV to 19/33

kV (excluding pressure assisted cables)

(EAC – 22 NACE – DM 34.3)

TRANSPORT EQUIPMENT

SABS 1329-4

Retro-reflective and fluorescent warning signs for road vehicles Part 4: Retro-reflective chevron signs SABS 1329-5 Retro-reflective and fluorescent warning signs for road vehicles Part 5: Retro-reflective chevron decals SANS 1017 Electric cables for motor vehicles - Low-voltage cables and flexible earthing straps for motor vehicles SANS 1080 Restraining devices (safety belts) for occupants of adult build in motor vehicles (revised requirements) SANS 1116-1 Retro-reflective registration plates for motor vehicles Part 1: Blanks (metal) SANS 1116-2 Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium) SANS 1116-4 Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics) SANS 1186-1 Symbolic safety signs Part 1: Standard signs and general requirements SANS 1186-4 Symbolic safety signs Part 4: Retro-reflective signs SANS 1186-5 Symbolic safety signs Part 5: Photoluminescent signs SANS 1191 High penetration-resistant laminated safety glass for vehicles SANS 1192 Laminated safety glass for vehicles SANS 1193 Toughened safety glass for vehicles SANS 1329-4 Retro-reflective and fluorescent warning signs for road vehicles Part 4: Retro-reflective chevron signs SANS 1329-5 Retro-reflective and fluorescent warning signs for road vehicles Part 5: Retro-reflective chevron decals

SANS 1505-1 Ball type couplings and towing brackets for towing caravans and light trailers Part 1: Towing brackets and

integrated towing devices SANS 1519-2 Road signs Part 2: Performance requirements for road signs SANS 1622 New replacement brake drums for motor vehicles

SANS 20003 Uniform provisions concerning the approval of retro-reflective devices for power-driven vehicles and their

trailers SANS 513 Retro-reflectors (reflex reflectors) (EAC – 23 NACE – DM

34.3)

SANS 785 Writing equipment - Ballpoint pens


Field Manager

ANNEXURE A



PORT ELIZABETH SCOPE

STANDARD PRODUCT

(EAC – 3 NACE – DA) FOOD PRODUCTS, BEVERAGES AND TOBACCOS

SANS 449

The manufacture of soft drinks and soft drink concentrates

(EAC – 4 NACE – DB) TEXTILES AND TEXTILE PRODUCTS

SANS 1387-4 Woven cotton and similar apparel fabrics Part 4: Cotton jean and drill fabrics SANS 1387-9 Woven cotton and similar apparel fabrics Part 9: Polyester-and-cotton shirt fabrics

SANS 1401-3 Woven cotton and similar household fabrics and articles Part 3: Cotton sheeting,

sheets, and pillowcases SANS 316 Industrial hand protectors (leather and fabric) and leather protective clothing SANS 434 Boiler suits and workwear suits

(EAC – 12 NACE – DG minus 24.4) CHEMICALS, CHEMICAL PRODUCTS AND FIBRES

SANS 1381-4 Materials for thermal insulation of buildings Part 4: Reflective foil laminates (rolls,

sheets and sections) SANS 1828 Cleaning chemicals for use in the food industry SANS 1853 Disinfectants and detergent-disinfectants for use in the food industry (EAC – 14 NACE – DH) RUBBER AND PLASTIC PRODUCTS

SANS 1173 General purpose textile-reinforced conveyor belting SANS 1366 Steel cord reinforced conveyor belting SANS 1374 Toothbrushes

SANS 20109 Uniform provisions concerning the approval for the production of retreaded

pneumatic tyres for commercial vehicles and their trailers SANS 4427 Polyethylene (PE) pipes for water supply - Specifications SANS 581 Semi-flexible vinyl floor tiles SANS 786 Flexible vinyl flooring SANS 791 Unplasticized poly(vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings SANS 952 Polyolefin film for damp- and waterproofing in buildings

SANS 966-1 Components of pressure pipe systems Part 1: Unplasticized poly(vinyl chloride)

(PVC-U) pressure pipe systems SANS 967 Unplasticized poly(vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe fittings SANS 971 Conveyor belting - Fire-retardant properties for all construction types

(EAC – 16 NACE – Di 26.5 & 6) CONCRETE, CEMENT, LIME, PLASTER ETC.

SANS 1058 Concrete paving blocks SANS 1215 Concrete masonry units

SANS 1263-1 Safety and security glazing materials for buildings Part 1: Safety performance of

glazing materials under human impact SANS 1294 Precast concrete manhole sections and components SANS 542 Concrete roofing tiles SANS 674 Steel-reinforced spirally wound PE drainage and sewer pipes SANS 676 Reinforced concrete pressure pipes SANS 677 Concrete non-pressure pipes SANS 927 Precast concrete kerbs, edgings and channels SANS 986 Precast reinforced concrete culverts SANS 1058 Concrete paving blocks


Field Manager

ANNEXURE A


PORT ELIZABETH SCOPE

STANDARD PRODUCT


SANS 121

Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods

SANS 1475-1 The production of reconditioned fire-fighting equipment Part 1: Portable and wheeled (mobile) rechargeable fire extinguishers

SANS 1475-2 The production of reconditioned fire-fighting equipment Part 2: Fire hose reels and above-ground hydrants

SANS 407 Austenitic manganese steel castings



SANS 1438-2 Helmet light assemblies for miners Part 2: Lead-acid batteries SANS 1438-4 Helmet light assemblies for miners Part 4: Helmet lights (headlights) SANS 1438-5 Helmet light assemblies for miners Part 5: Helmet light assemblies SANS 475 Luminaires for interior lighting, streetlighting and floodlighting - Performance requirements SANS 60598-2-1 Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires SANS 60598-2-5 Luminaires Part 2-5: Particular requirements - Floodlights SANS 60896-11 Stationary lead-acid batteries Part 11: Vented types - General requirements and methods of test SANS 60896-21 Stationary lead-acid batteries Part 21: Valve regulated types - Methods of test SANS 60898-22 Stationary lead-acid batteries Part 22: Valve regulated types - Requirements SANS 61084-1 Cable trunking and ducting systems for electrical installations Part 1: General requirements

(EAC – 22 NACE – DM 34.3) TRANSPORT EQUIPMENT

SANS 1116-2 Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium) SANS 1116-4 Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics) SANS 1191 High penetration-resistant laminated safety glass for vehicles SANS 1192 Laminated safety glass for vehicles SANS 1193 Toughened safety glass for vehicles SANS 2 Lead-acid starter batteries

SANS 50286-2 Simple unfired pressure vessels designed to contain air or nitrogen Part 2: Pressure vessels for air

braking and auxiliary systems for motor vehicles and their trailers SANS 60254-1 Lead-acid traction batteries Part 1: General requirements and methods of test


ISSUED BY THE SOUTH AFRICAN NATIONAL ACCREDITATION SYSTEM

Field Manager

sabs commercial soc ltd co. reg. no: 2000/013581/07 · pdf filesans 1675 sans 449 the...

Documents