sand vik
TRANSCRIPT
Ro
ck
drillin
g to
ols
To
p h
am
me
r pro
du
cts
www.sandvik.com
Sandvik Mining and Construction Tools ABSE-811 81 Sandviken, Sweden. Tel +46 26 26 20 00 Fax +46 26 26 23 00
HR-12281-ENG AB Sandvikens Tryckeri
Top hammer drilling tools Product catalogue
Products from Sandvik Mining and Construction Tools
Small hole drilling 3
Drifting and tunneling 17
Bench drilling 33
Long hole drilling 49
Rock reinforcement 63
Shank adapters 73
Grinding 91
Auxiliary tools 113
Product code information 119
Safety information 121
Numerical index with weight table 122
Notes 131
CopyrightSandvik Mining and Construction Tools ABSandviken
Top hammer products
Concerning bit diameters
Note that all bits are bigger on diameter than the given measurements in the catalogue.
Cross bits: Can be max 1 mm larger due to manufacturing tolerances.
Button bits: Are max 3,0 mm larger for some designs in order to make up for fast initial
wear on the diameter. The minimum diameter is 1,5 mm above given measurement.
Keep in mind that a bit always gives a bigger hole than the stated bit diameter.
This product catalogue is a presentation of the global
stock standard range of top-hammer rock tools manufactured by
Sandvik Mining and Construction Tools AB
Bit classifi cation code
H Very hard to hard rock > 2500 bar (250 MPa)M Medium hard rock 1500-2500 bar (150-250 MPa)S Soft rock < 1500 bar (150 MPa)
C Homogeneous (competent) rockF Fissured rock
V Very abrasive rock > 40% silicaA Abrasive rock 20-40% silicaN Non-abrasive rock 0-20% silica
_
_
Small hole drilling
Small hole drilling
Page
H19 (3/4) Integral drill steels ..........................................................5
H22 (7/8") Integral drill steels ........................................................6
Reaming tools ...................................................................................7
H22 Tapered tools, 12° taper .........................................................8
H22 Tapered tools, 11° taper ..........................................................9
Stone working tools .......................................................................10
R22 (7/8") Extension drilling tools ...............................................11
R23 (29/32") Extension drilling tools ...........................................12
R25 (1") Extension drilling tools ...................................................13
Sandvik Alpha. α250 bit thread ....................................................15
R28 (1 1/8") Extension drilling tools ............................................16
TOP HAMMER DRILLING TOOLS • 5
Small hole drillingH19 (3/4) Integral drill steels
A B22
A B
D
L108
19
1-1_7
Shank 22 x 108 mm (7/8"x 4 1/4")
400 1' 4" 24 15/16" 728-0424 400 1' 4" 29 1 9/64" 728-0429 800 2' 7" 28 1 7/64" 728-08281600 5' 3" 27 1 1/16" 728-1627
Shank 19 x 108 mm (3/4"x 4 1/4")
Dimensions Part No.L Dmm ft in mm in
400 1' 4" 29 19/64" 724-0429 800 2' 7" 28 1 7/64" 724-0828 1600 5' 3" 27 1 1/16" 724-1627 2400 7' 10" 26 1 1/32" 724-2426
600 2' – 27 1 1/16" 724-0627 1200 3' 11" 26 1 1/32" 724-1226
400 1' 4" 24 15/16" 724-0424 800 2' 7" 23 29/32" 724-0823
BA
L
D
A B108
1-1_6
19 19
Series
21
24
Boulder steel
6 • TOP HAMMER DRILLING TOOLS
Small hole drillingH22 (7/8") Integral drill steels
Shank 22x108 mm (7/8" x 4 1/4")
Dimensions Part No.L Dmm ft in mm in
800 2' 7" 34 1 11/32" 714-0834-651600 5' 3" 33 1 19/64" 714-1633-652400 7' 10" 32 1 1/4" 714-2432-653200 10' 6" 31 1 7/32" 714-32314000 13' 1" 30 1 3/16" 714-40304800 15' 9" 29 1 9/64" 714-48295600 18' 4" 28 1 7/64" 714-5628-506400 21' – 27 1 1/16" 714-6427-507200 23' 8" 26 1 1/32" 714-7226-50
800 2' 7" 40 1 37/64" 714-0840-651600 5' 3" 39 1 17/32" 714-1639-652400 7' 10" 38 1 1/2" 714-2438-653200 10' 6" 37 1 29/64" 714-3237-654000 13' 1" 36 1 27/64" 714-4036-654800 15' 9" 35 1 3/8" 714-4835-655600 18' 4" 34 1 11/32" 714-5634-656400 21' – 33 1 19/64" 714-6433-657200 23' 8" 32 1 1/4" 714-7232-65
400 1' 4" 34 1 11/32" 714-0434-65 800 2' 7" 33 1 19/64" 714-0833-651200 3' 11" 32 1 1/4" 714-1232-651600 5' 3" 31 1 7/32" 714-16312000 6' 7" 30 1 3/16" 714-2030
600 2' – 35 1 3/8" 714-0635-651200 3' 11" 34 1 11/32" 714-1234-651800 5' 11" 33 1 19/64" 714-1833-652400 7' 10" 32 1 1/4" 714-2432-65
600 2' – 41 1 5/8" 714-0641-651200 3' 11" 40 1 37/64" 714-1240-651800 5' 11" 39 1 17/32" 714-1839-652400 7' 10" 38 1 1/2" 714-2438-65
Series
11
12
13
16
17
2000 6' 7" 33 1 19/64" 714-2033-658000 26' 3" 26 1 1/32" 714-8026-50 8800 28' 11" 25 1" 714-8825-5005 9600 31' 6" 25 1" 714-9625-5005
LA B
22 22
1-1_4
108
BA
D
Shank 22x108 mm (7/8"x 4 1/4")
800 2' 7" 29 1 9/64" 714-08291600 5' 3" 28 1 7/64" 714-1628-502400 7' 10" 27 1 1/16" 714-2427-50
L
D
A B22 22
108
1-1
5
BA
Shank 22x108 mm (7/8"x 4 1/4")
LA B
22 22
1-1_4
108
BA
D
TOP HAMMER DRILLING TOOLS • 7
Small hole drillingReaming tools
Pilot rodReaming bit
2-1_
114
795-1469
Knock-off tool for reaming bit
2-1_
110
D
4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45
Reaming bit, 6° taper
Buttons, mm Dimensions Part No.Front Gauge DNo Size No Size Angle mm in
800 2' 7 1/2" 26 1 1/32" 7922-6108-111200 3' 11 3/4" 26 1 1/32" 7922-6112-111600 5' 3" 26 1 1/32" 7922-6116-112000 6' 6 3/4" 26 1 1/32" 7922-6120-112500 8' 2 1/2" 26 1 1/32" 7922-6124-11
Pilot rod, Hex 22, 6° taper
L D Part No.mm ft in mm in
L22
108 2-1_
11222
D
8 • TOP HAMMER DRILLING TOOLS
Small hole drillingH22 Tapered tools, 12° taper
1-1_
27
Tapered rod
Cross bit
Button bit, short skirt
Button bit, long skirt
Flushinghole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo Size No Size No Size No Size Angle mm in
Cross bit
1x4 2x4 – – – 28 1 1/8" 7770-9028-421x4 2x4 – – – 30 1 3/16" 7770-9030-421x6 2x4.5 – – – 32 1 1/4" 7770-9032-42 1x6 2x4.5 – – – 35 1 3/8" 7770-9035-42
D
2-1_
466
Button bit
1x5 1x5 1x7 4x7 35° 28 1 1/8" 7795-6428-B481x5 1x5 1x7 4x7 35° 30 1 3/16" 7795-6430-B48
D
2-1_
465
Button bit
2x4 1x4 2x7 5x7 40° 32 1 1/4" 7795-5232-B482x4 1x3,5 2x7 5x8 40° 35 1 3/8" 7795-5235-B48 2x4 1x4 2x7 5x9 40° 38 1 1/2" 7795-5238-B48
D
2-1_
394
C
Button bit
2x4 1x3.5 2x7 5x7 40° 33 1 9/64" 7770-5233-B48 2x4 1x3.5 2x7 5x8 40° 35 1 3/8" 7770-5235-B48
L1081-1_21
Tapered rod, shank 22x108, HF-hardened - For surface drilling
2440 8' – 22 7/8" 7870-5124-11 3200 10' 6” 22 7/8" 7870-5132-114000 13' 1 1/2” 22 7/8" 7870-1140-114400 14' 5” 22 7/8" 7870-1144-11 4800 15' 9” 22 7/8" 7870-1148-115600 18' 4 1/2” 22 7/8" 7870-1156-116400 21' – 22 7/8" 7870-1164-117200 23' 7 1/2” 22 7/8" 7870-1172-118000 26' 3” 22 7/8" 7870-1180-11 8800 28' 10 1/2” 22 7/8" 7870-1188-11
L1081-1_21
Tapered rod, shank 22x108, carburized
610 2' – 22 7/8" 7870-6106-111220 4' – 22 7/8" 7870-6112-111830 6' – 22 7/8" 7870-6118-112000 6' 7” 22 7/8" 7870-6120-112440 8' – 22 7/8" 7870-6124-113050 10' – 22 7/8" 7870-6131-113660 12' – 22 7/8" 7870-6137-11
D
2-1_
393
Dimensions Part No.L Dmm ft in mm in
TOP HAMMER DRILLING TOOLS • 9
Small hole drillingH22 Tapered tools, 11° taper
1-1_
28 Tapered rod
Button bit
Flushinghole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo Size No Size No Size No Size Angle mm in
Button bit
D
2-1_
464
1x6 2x4 2x7 3x8 35° 32 1 1/4" 7776-1932-B48 1x6 1x6 1x8 3x9 40° 36 1 7/16" 7776-1936-B48 1x6 1x6 2x8 3x9 40° 38 1 1/2" 7776-1938-B48 1x6 1x6 2x8 3x9 40° 40 1 37/64" 7776-1940-B48
D
2-1_
466
Button bit
1x6 1x6 2x8 4x8 40° 38 1 1/2" 7776-6438-B48
D
2-1_
465
Button bit
1x4 1x6 2x7 5x7 40° 32 1 1/4" 7776-4432-B48 1x5 1x5 2x7 5x7 35° 35 1 3/8" 7776-4435-B48 1x6 1x5 2x7 5x8 35° 38 1 1/2" 7776-4438-B48 1x6 1x5 2x8 5x9 35° 40 1 37/64" 7776-4440-B48
L1081-1_21
610 2' – 22 7/8" 7876-6106-11 800 2’ 7 1/2” 22 7/8” 7876-6108-111220 4' – 22 7/8" 7876-6112-111830 6' – 22 7/8" 7876-6118-112000 6’ 7” 22 7/8” 7876-6120-112440 8' – 22 7/8" 7876-6124-113050 10' – 22 7/8" 7876-6131-113600 11' 9 1/2” 22 7/8" 7876-6136-11
Tapered rod, shank 22x108, carburized
Dimensions Part No.L Dmm ft in mm in
10 • TOP HAMMER DRILLING TOOLS
Small hole drillingStone working tools
9-1_
32
Plug hole integral steel
Shank rod
Cross bit
Dimensions Part No.L Dmm ft in mm in
D
1089-1_31
19
L
Plug hole integral steel
150 6" 17 21/32" 721-1517 160 6 1/4" 20 25/32" 721-1620 200 7 7/8" 20 25/32" 721-2020 240 9 29/64" 20 25/32" 721-2420 280 11 1/32" 20 25/32" 721-2820 310 11 1/4" 20 25/32" 721-3120 160 6 1/4" 22 7/8" 721-1622 190 7 1/2" 22 7/8" 721-1922
L108R 25
2-1_
207
DDShank rod, Hex22 - R25
255 10 3/64" 22 7/8" 7802-6103-13 800 2' 2 1/2" 22 7/8" 7802-6108-13 1000 3' 3" 22 7/8" 7802-6110-13
D9_13
Cross bit, R25
381 1/2" 7732-1438-42 411 5/8" 7732-1441-42 451 3/4" 7732-1045-42
TOP HAMMER DRILLING TOOLS • 11
Small hole drillingR22 (7/8") Extension drilling tools
2-1_
395
Extension rodCoupling sleeveShank adapter
Cross bit
Shank rod
L
D
2-1_
80
Coupling sleeve, R22
140 – 5 1/2" 31 1 7/32" 7991-2031
255 – 10 3/64" 22 7/8" 7801-6103-13 1000 3' 3" 22 7/8" 7801-6110-13
3-1_
150
22108
R22L
Shank adapter/Shank rod, Hex 22 - R22
LR 22 R 22 2-
1_20
5
D
Extension rod R22 - Hex 22 - R22
800 2' 7" 22 7/8" 7851-1308-201200 3' 11" 22 7/8" 7851-1312-201600 5' 3" 22 7/8" 7851-1316-20
Dimensions Part No.L Dmm ft in mm in
1 4.5 2 4.5 38 1 1/2" – 7731-1038-42
Cross bit
2-1_
77
D
Flushing hole, mm Bit Part No.Front Gauge D classi-No Size No Size mm in fi cation
12 • TOP HAMMER DRILLING TOOLS
Small hole drillingR23 (29/32") Extension drilling tools
2-1_
502A Shank adapter
MF-rod
Shank rod
Cross bit
Button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1 5.0 1 6 2x7 5x8 40° 35 1 3/8" HMCA 7737-5235-R481 6.0 1 6 2x7 5x8 35° 38 1 1/2" HMCA 7737-4438A-B481 5.0 1 6 2x8 5x9 35° 41 1 5/8" HMCA 7737-5241-R48
3 5.0 – 3x8 6x9 30° 45 1 3/4" HMCA 7737-5345-R48
Button bit
2-1_
384
D
2-1
_4
D
Cross bit, Extra Heavy Duty
1 4.5 2 4.5 – – – 33 1 5/16" – 7737-1633-11
2-1
_4
D
Cross bit, Heavy Duty
1 4.5 2 4.5 – – – 35 1 3/8" – 7737-1435-421 4.5 2 4.5 – – – 38 1 1/2" – 7737-1438-42
L
2-1_
334
22108
R23
Shank adapter / Shank rod, Hex 22 - R23
255 – 10 3/64" 22 7/8" 7807-6103-112400 8' – 22 7/8" 7807-6124-113200 10' – 22 7/8" 7807-6132-113600 11' 9 5/8” 22 7/8" 7807-6136-11
L
2-1
314
R23 R23D
MF-rod, R23 - Hex 22 - R23
Female end OD 31 mm.
2095 6' 10 1/2" 22 7/8" 7857-4821-203050 10' – 22 7/8" 7857-4831-20
L D mm ft in mm in Part No.
2-1_
316
D
Shank rod, Hex 25 - R23
255 – 10 3/64" 25 1" 7807-7103-113600 11' 9 " 25 1" 7807-7136-11
108
2-1_
188c
R23L
25 D
TOP HAMMER DRILLING TOOLS • 13
Small hole drillingR25 (1") Extension drilling tools
2-1_
397
Shank adapter Extension rodCoupling sleeve
Button bit
Cross bit
Shank rod
Shank adapter / rod, Hex 22 x R25
L
3-1_
149
22108
R25
255 – 10 3/64" 22 7/8" 7802-6103-13 800 2' 7" 22 7/8" 7802-6108-131000 3' 3" 22 7/8" 7802-6110-13
Dimensions Part No.L Dmm ft in mm in
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x5 1x6 2x7 5x8 35° 35 1 3/8" HMCA 7732-5235-S481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7732-5238-S481x5 1x6 2x7 5x9 35° 38 1 1/2" HMCA 7732-5238-R481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7732-5241-S48
3x4.5 – 3x8 6x9 40° 45 1 3/4" MSCFAN 7732-5345F-R48
Button bit
2-1_
384
D
1)1)
2-1
_4
D
Cross bit, Heavy Duty
1x5 2x5 – – – 35 1 3/8" – 7732-1435-421x5 2x5 – – – 38 1 1/2" – 7732-1438-421x5 2x5 – – – 41 1 5/8" – 7732-1441-42
1)1)
1) For one-rod drilling.
Cross bit
1x5 2x5 – – – 45 1 3/4" – 7732-1045-421x5 2x5 – – – 51 2" – 7732-1051-42
2-1_
3
D
2-1_
316
D
14 • TOP HAMMER DRILLING TOOLS
Small hole drillingR25 (1") Extension drilling tools
Extension rod, R25 - Hex 25 - R25
915 3' – 25 1" 7852-2309-201220 4' – 25 1" 7852-2312-201525 5' – 25 1" 7852-2315-201830 6' – 25 1" 7852-2318-20 2435 8' – 25 1" 7852-2324-203050 10' – 25 1" 7852-2331-20
Dimensions Part No.L Dmm ft in mm in
LR 25 R 25D
2-1_
5
2-1_
6
L
D
Coupling sleeve, R25
160 – 6 1/4" 35 1 3/8" 7992-2035
TOP HAMMER DRILLING TOOLS • 15
Small hole drillingSandvik Alpha. α250 bit thread
Button bit
2-1_
397b
Button bitShank rod
1x5 1x6 2x7 5x8 40° 35 1 3/8" HMCA 7764-5235-R481x5 1x6 2x7 5x9 35° 38 1 1/2" HMCA 7764-5238-R48
3x4.5 – 3x8 6x9 40° 45 1 3/4" MSCFAN 7764-5345F-R48
2-1_
384
D
2-1_
316_
1
D
108
2-1_
188b
250L
25 D
Shank rod, Hex 25 - α250
3600 11' 9 5/8 " 25 1" 7814-7136-11
Dimensions Part No.L Dmm ft in mm in
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
16 • TOP HAMMER DRILLING TOOLS
2-1_
398b
Small hole drillingR28 (1 1/8") Extension drilling tools
Extension rodShank adapter Coupling sleeve
Button bit
Cross bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x5 1x6 2x7 5x9 35° 38 1 1/2" MSCFAN 7739-5238-R481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7739-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7739-5241-S481x5 1x6 2x8 5x10 35° 43 1 11/16" HMCA 7739-5243-S48
Button bit, CAPP 52
2-1_
384
D
1)1)1)
2-1_
4
D
Cross bit, Heavy Duty
1x5 2x5 – – – 38 1 1/2" – 7739-1438-421x5 2x5 – – – 41 1 5/8" – 7739-1441-42
1)1)
2-1_
16
LR 28 R 28D
Extension rod, R28 - Hex 28 - R28
150 – 5 29/32" 40 1 37/64" 7999-3640
L
D
2-1_
214
Coupling sleeve, R28
1) For one-rod drilling.
3050 10' – 28 1 1/8" 7859-2931-20
Dimensions Part No.L Dmm ft in mm in
Drifting and tunneling
Drifting and tunneling
Page
R25 (1") bit thread .........................................................................19
Sandvik Alpha. α250 bit thread ..................................................21
R28 (1 1/8") bit thread ..................................................................22
Sandvik Alpha. α280 bit thread ....................................................23
R32 (1 1/4") bit thread .................................................................24
Sandvik Alpha. α330 bit thread ...................................................27
Sandvik Jumbo. R35 (1 3/8") bit thread ......................................29
Sandvik Extra. R35 (1 3/8") bit thread .........................................31
Sandvik RT300 bit types ................................................................32
TOP HAMMER DRILLING TOOLS • 19
2-1_
407
Drifting and tunnelingR25 (1") bit thread
RT300 button bit, type 52
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x5 1x6 2x7 5x8 35° 35 1 3/8" HMCA 7732-5235-S481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7732-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8” HMCA 7732-5241-S482-
1_38
4
D
Cross bit, Heavy Duty
1x5 2x5 – – – 35 1 3/8" – 7732-1435-421x5 2x5 – – – 38 1 1/2" – 7732-1438-421x5 2x5 41 1 5/8” – 7732-1441-422-
1_4
D
RT300 button bit, type 52 for bolt ERB 120/120+
1x5 1x6 2x7 5x9 30° 37 1 29/64" HMCA 7732-5237-S48
Shank adapter Drifter rodCross bit
Button bit
Reaming tools
Coupling sleeve
Dimensions Part No.L Dmm ft in mm in
L
2-1_
337
R25DR32
Drifter rod, R32 - Hex 25 - R25
2475 8' 1 21/32" 25 1" 7853-6224-202630 8' 7 9/16” 25 1” 7853-6226-20 3090 10' 1 21/32" 25 1" 7853-6231-20
Flushing hole Ø 8.8 mm.
2-1_
384
D
20 • TOP HAMMER DRILLING TOOLS
Drifting and tunneling R25 (1") bit thread
150 – 5 29/32" 44 1 47/64" 7993-3644
L
2-1
_17
D
R32 coupling sleeve
Dimensions Part No.L Dmm ft in mm in
Reaming tools for cut holes / Pilot adapter, 6° taper
– – 26 1 1/32" 7822-2526
2-1_116
D
ThreadR25
4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45
2-1_
110
D
Reaming tools for cut holes / Reaming bit, 6° taper
Dimensions Part No.Buttons, mm DFront Gauge Angle mm in
TOP HAMMER DRILLING TOOLS • 21
Drifting and tunnelingSandvik Alpha. α250 bit thread
2-1_
407b
RT300 button bit, type 52
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x4,5 1x6 2x7 5x7 45° 33 1 5/16" HMCA 7764-4433-S481x5 1x6 2x7 5x9 35° 35 1 3/8" HMCA 7764-4435-S481x5 1x6 2x7 5x9 30° 37 1 29/64" HMCA 7764-5237-S481x6 1x6 2x7 5x9 35° 38 1 1/2" HMCA 7764-5238-S481x6 1x6 2x8 5x9 35° 41 1 5/8” HMCA 7764-5241-S48
2-1_
384
D
Cross bit
1x5 2x5 – – – 33 1 5/16" – 7764-1633-421x5 2x5 – – – 35 1 3/8" – 7764-1435-421x5 2x5 – – – 38 1 1/2" – 7764-1438-421x5 2x5 41 1 5/8” – 7764-1441-42
2-1_
4
D
Shank adapter Drifter rod
Cross bit
Button bit
Reaming toolsCoupling sleeve
Dimensions Part No.L Dmm ft in mm in
L
2-1_
337b
DR32 250
Drifter rod, R32 - Hex 25 - α250
2475 8' 1 7/16" 25 1" 7853-1724-202630 8' 7 9/16" 25 1" 7853-1726-203190 10' 5 19/32" 25 1" 7853-1731-203700 12' 1 1/2" 25 1" 7853-1737-20
Flushing hole Ø 8.6 mm.
150 – 5 29/32" 44 1 47/64" 7993-3644
L
2-1
_17
D
R32 coupling sleeve
Reaming tools for cut holes / Pilot adapter, 6° taper
– – – 26 1 1/32" 7822-2726
2-1_116
DThread α250
4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45
2-1_
110
D
Reaming tools for cut holes / Reaming bit, 6° taper
Dimensions Part No.Buttons, mm DFront Gauge Angle mm in
L
2-1_
337b
DR32 250
Drifter rod, R32 - Hex 28 - α250
2475 8' 1 7/16" 28 1 1/8" 7853-1824-202630 8' 7 9/16" 28 1 1/8" 7853-1826-202935 9' 7 9/16" 28 1 1/8" 7853-1829-203190 10' 5 19/32" 25 1" 7853-1831-20
Flushing hole Ø 8.8 mm.
22 • TOP HAMMER DRILLING TOOLS
R32 Coupling sleeve
150 – 5 29/64" 44 1 47/64" 7993-3644
L
2-1
_17
D
2-1_116
D
Reaming tools for cut holes / Pilot adapter 6° taper
– – – 26 1 1/32" 7822-1526Thread
R28
Reaming tools for cut holes / Reaming bit 6° taper
2-1_
110
D
Drifting and tunnelingR28 (1 1/8") bit thread
RT300 button bit, type 52
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x5 1x6 2x7 5x9 35° 38 1 1/2" MCAN 7739-5238-R481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7739-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7739-5241-S482-
1_38
4
D
Button bit
Reaming tools
Coupling sleeve Drifter rodShank adapter
Dimensions Part No.L Dmm ft in mm in
Drifter rod, R32 - Hex 28 - R28
L
2-1_
339
R28R32 D
3090 10' 1 21/32" 28 1 1/8" 7853-7631-203700 12' 1 1/2" 28 1 1/8" 7853-7637-20
Flushing hole Ø 8.8 mm.
2-1_
407b
Cross bit
Cross bit , Heavy Duty
2-1_
4
D
1x5 2x5 – – – 38 1 1/2" – 7739-1438-42
4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45
TOP HAMMER DRILLING TOOLS • 23
Drifting and tunnelingSandvik Alpha. α280 bit thread
R32 Coupling sleeve
150 – 5 29/64" 44 1 47/64" 7993-3644
L
2-1
_17
D
RT300 button bit, type 52
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x5 1x6 2x7 5x9 35° 38 1 1/2" MCAN 7765-5238-R481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7765-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7765-5241-S481x5 1x6 2x8 5x10 35° 43 1 11/16" HMCA 7765-5243-S48
2-1_
384
D
Button bit
Reaming tools
Coupling sleeve Drifter rodShank adapter
Dimensions Part No.L Dmm ft in mm in
Drifter rod, R32 - Hex 28 - α280
L
2-1_
339
R28R32 D
3090 10' 1 21/32" 28 1 1/8" 7853-2631-203700 12' 1 1/2" 28 1 1/8" 7853-2637-20
Flushing hole Ø 8.8 mm.
2-1_
407b
Cross bit
α280
2-1_116
D
Reaming tools for cut holes / Pilot adapter 6° taper
– – – 26 1 1/32" 7822-2826Thread
R28
Reaming tools for cut holes / Reaming bit 6° taper
2-1_
110
D
Cross bit , Heavy Duty
2-1_
4
D
1x5 2x5 – – – 38 1 1/2" – 7765-1438-42
4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45
α280
24 • TOP HAMMER DRILLING TOOLS
Drifting and tunnelingR32 (1 1/4") bit thread
RT300 button bit, type 52
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x5 1x7.5 2x9 5x10 35° 43 1 11/16" HMCVA 7733-5243-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HMCVA 7733-5245-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HCV 7733-5245-S651x6 1x7.5 2x9 5x11 35° 48 1 7/8" HMCVA 7733-5248-S481x6 1x7.5 2x10 5x12 35° 51 2" HMCVA 7733-5251-S481x6 1x7.5 2x10 5x12 35° 51 2" HCV 7733-5251-S65
2-1_
386
D
RT300 button bit, type 53
3x4.5 – 3x8 6x10 25° 45 1 3/4" HMCAN 7733-5345-S483x4.5 – 3x8 6x10 30° 45 1 3/4" MSCAN 7733-5345-R483x5 – 3x9 6x10 30° 48 1 7/8" HMCAN 7733-5348-S483x6 – 3x9 6x10 35° 51 2" HMCAN 7733-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7733-5351-R48
2-1_
316
D
RT300 button bit, type 54
2x6 – 2x9 6x9 40° 43 1 11/16" MSCAN 7733-5443-R482x6 – 2x9 6x10 35° 45 1 3/4" MSCAN 7733-5445-R482x7 – 2x9 6x10 40° 48 1 7/8" MSCAN 7733-5448-R482x7 – 2x10 6x10 40° 51 2" MSCAN 7733-5451-R48
2-1_
294
D
Cross bit, Heavy Duty
1x5 4x6 – – – 45 1 3/4" – 7733-1345A-42
2-1_
24
D
MF-rod
Reaming tools
Shank adapter
Coupling sleeve Drifter rod
Button bit
Cross bit
TOP HAMMER DRILLING TOOLS • 25
Drifting and tunnelingR32 (1 1/4") bit thread
Drifter rod, R38 - Hex 35 - R32
Dimensions Part No.L Dmm ft in mm in
3090 10' 1 21/32" 35 1 3/8" 7854-9631-203700 12' 1 1/2" 35 1 3/8" 7854-9637-204305 14' 1 31/64" 35 1 3/8" 7854-9643-204915 16' 1 1/2" 35 1 3/8" 7854-9649-20L
R32R38
2-1_
342
D
Flushing hole Ø 9.5 mm.
Drifter rod, R38 - Hex 32 - R32
3700 12' 1 1/2" 32 1 1/4" 7854-8637-204305 14' 1 31/64" 32 1 1/4" 7854-8643-204915 16' 1 1/2" 32 1 1/4" 7854-8649-20
Flushing hole Ø 9.6 mm.
MF-rod, T38 - Hex 35 - R32
3700 12' 1 1/2" 35 1 3/8" 7324-6537-204305 14' 1 31/64" 35 1 3/8" 7324-6543-20
R 32LT 38
2-1_
301
D
Flushing hole Ø 9.5 mm.Female end OD 56 mm.
Drifter rod, T38 - Hex 35 - R323090 10' 1 21/32" 35 1 3/8" 7324-9631-203700 12' 1 1/2" 35 1 3/8" 7324-9637-204305 14' 1 31/64" 35 1 3/8" 7324-9643-204915 16' 1 1/2" 35 1 3/8" 7324-9649-205525 18' 1 33/64" 35 1 3/8" 7324-9655-206135 20' 1 1/2" 35 1 3/8" 7324-9661-20
2-1_
344
LR32T38 D
Flushing hole Ø 9.5 mm.
Coupling sleeve
L
2-1_
361
D
170 – 6 3/4" 55 2 5/32" 7994-3655191 – 7 1/2" 52 2" 7314-3652
R38T38
Drifter rod, T38 - Hex 32 - R32
3700 12' 1 1/2" 32 1 1/4" 7324-8637-204305 14' 1 31/64" 32 1 1/4" 7324-8643-20
Flushing hole Ø 9.6 mm.
2-1_
343
LT38 R32D
LR32R38
2-1_
342
D
26 • TOP HAMMER DRILLING TOOLS
Drifting and tunnelingR32 (1 1/4") bit thread
Reaming tools for cut holes / Reaming bit, 6° taper
2-1_
110
D
4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45
Reaming tools for cut holes / Reaming bit, 12° taper
2-1_
118
D
4x10 8x12 35° 89 3 1/2" 7721-4889-S454x12 8x12 35° 102 4" 7721-4802-S454x12 8x12 35° 127 5" 7721-4827-S45
Buttons, mm Dimensions Part No.Front Gauge DNo Size No Size Angle mm in
– – – 26 1 1/32" 7822-3526
2-1_116
D
Reaming tools for cut holes / Pilot adapter, 6° taper
ThreadR32
Reaming tools for cut holes / Pilot adapter, 12° taper
2-1_117
D– – – 40 1 37/64" 7821-3440
ThreadR32
Reaming tools for cut holes / Reaming bit, R32
Flushing hole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo size No Size No Size No Size Angle mm in
2x6 2x6 1x13 16x13 35° 102 4" 7733-5602-S45
D
2-1_
538
TOP HAMMER DRILLING TOOLS • 27
RT300 button bit, type 52
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
1x5 1x7.5 2x9 5x10 35° 43 1 11/16" HMCVA 7766-5243-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HMCVA 7766-5245-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HCV 7766-5245-S651x6 1x7.5 2x9 5x11 35° 48 1 7/8" HMCVA 7766-5248-S48
2-1_
386b
D
RT300 button bit, type 533x4.5 1x5 3x8 6x10 30° 45 1 3/4" MSCAN 7766-5345A-R483x4.5 1x5 3x8 6x10 25° 45 1 3/4" HMCAN 7766-5345A-S483x5 1x5 3x9 6x10 30° 48 1 7/8" MSCAN 7766-5348A-R483x5 1x5 3x9 6x10 30° 48 1 7/8" HMCAN 7766-5348A-S483x6 1x5 3x9 6x10 35° 51 2" MSCAN 7766-5351A-R483x6 1x5 3x9 6x10 35° 51 2" HMCAN 7766-5351A-S48
2-1_
316b
D
RT300 button bit, type 54
2x6 – 2x9 6x9 40° 43 1 11/16" MSCAN 7766-5443-R482x6 – 2x9 6x10 35° 45 1 3/4" MSCAN 7766-5445-R48
2-1_
294b
D
-1_409b
Reaming toolsShank adapter Coupling sleeve Drifter rod
Button bit
Drifter rod, T38 - Hex 35 - α330
2-1_
470
Lα 330T38 D
3090 10' 1 21/32" 35 1 3/8" 7324-4131-203700 12' 1 1/2" 35 1 3/8" 7324-4137-204305 14' 1 31/64" 35 1 3/8" 7324-4143-204915 16' 1 1/2" 35 1 3/8" 7324-4149-205525 18' 1 33/64" 35 1 3/8" 7324-4155-20
Flushing hole Ø 9.5 mm.
Cross bit
1x5 4x6 45 1 3/4" 7766-1345A-421x5 2x7.5 48 1 7/8" 7766-1448-42
2-1_
24
D
Dimensions Part No.L Dmm ft in mm in
Drifting and tunnelingSandvik Alpha. α330 bit thread
3090 10' 1 21/32" 39 1 1/2" 7324-4231-203700 12' 1 1/2" 39 1 1/2" 7324-4237-204305 14' 1 31/64" 39 1 1/2" 7324-4243-204915 16' 1 1/2" 39 1 1/2" 7324-4249-205525 18' 1 33/64" 39 1 1/2" 7324-4255-206135 20' 1 1/2" 39 1 1/2" 7324-4261-206400 21' – 39 1 1/2" 7324-4264-20
2-1_
469
LT38 D α 330
Drifter rod, T38 - Round 39 - α 330
Flushing hole Ø 10.3 mm.
28 • TOP HAMMER DRILLING TOOLS
Reaming tools for cut holes / Reaming bit, 12° taper
2-1_
118
D
4x10 8x12 35° 89 3 1/2" 7721-4889-S454x12 8x12 35° 102 4" 7721-4802-S454x12 8x12 35° 127 5" 7721-4827-S45
Reaming tools for cut holes / Pilot adapter, 12° taper
2-1_117b
D 40 1 37/64” 7821-3040
Thread α330
Reaming tools for cut holes / α330 reaming bit
2x6 2x6 1x13 16x13 35° 102 4" 7766-5602-S45
D
2-1_
538b
Drifting and tunnelingSandvik Alpha. α330 bit thread
Flushinghole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge D No Size No Size No Size No Size Angle mm in
T38 coupling sleeve
L
2-1_
361
D191 – 7 1/2" 52 2" 7314-3652
Dimensions Part No.L Dmm ft in mm in
TOP HAMMER DRILLING TOOLS • 29
Drifting and tunnelingSandvik Jumbo. R35 (1 3/8") bit thread
RT300 button bit, type 53
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
3x5 1x5 3x9 6x10 30° 48 1 7/8" HMCAN 7738-5348A-S483x5 1x5 3x9 6x10 30° 48 1 7/8" MSCAN 7738-5348A-R483x5 – 3x9 6x10 30° 48 1 7/8" HMCAN 7738-5348-S483x5 – 3x9 6x10 30° 48 1 7/8" MSCAN 7738-5348-R483x6 – 3x9 6x10 35° 51 2" HMCAN 7738-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7738-5351-R48
2-1_
316
D
RT300 button bit, type 52
1x5 1x7.5 2x9 5x11 35° 48 1 7/8" HMCVA 7738-5248-S481x5 1x7.5 2x10 5x12 35° 51 2" HMCVA 7738-5251-S48
2-1_
511
D
2-1_
506
Reaming tools
Shank adapterCoupling sleeve
Drifter rod, Hex.
Button bitDrifter rod, Round
T38 coupling sleeve
191 – 7 1/2" 52 2" 7314-3652
4305 14' 1 31/64" 39 1 1/2" 7324-7243-204915 16' 1 1/2" 39 1 1/2" 7324-7249-205525 18' 1 33/64" 39 1 1/2" 7324-7255-202-
1_46
9
LR35T38 D
Drifter rod, T38 - Round 39 - R35
Dimensions Part No.L Dmm ft in mm in
Flushing hole Ø 14.5 mm.
Drifter rod, T38 - Hex 35 - R35
2-1_
470
LR35T38 D
4305 14' 1 31/64" 35 1 3/8" 7324-8543-204915 16' 1 1/2" 35 1 3/8" 7324-8549-205525 18' 1 33/64" 35 1 3/8" 7324-8555-206135 20' 1 1/2" 35 1 3/8" 7324-8561-20
Flushing hole Ø 9.5 mm.
L
2-1_
227
D
T38 T38
Cross bit, Heavy Duty
1x5 2x7.5 – – – 48 1 7/8" – 7738-1448-42
2-1_
24
D
30 • TOP HAMMER DRILLING TOOLS
Drifting and tunnelingSandvik Jumbo. R35 (1 3/8") bit thread
2-1_117
D
ThreadR35
Reaming tools for cut holes / Pilot adapter, 12° taper
Buttons, mm Dimensions Part No.Front Gauge DNo Size No Size Angle mm in
– – – 40 1 37/64" 7821-5440
Reaming tools for cut holes / Reaming bit, 12° taper
2-1_
118
D
4x10 8x12 35° 89 3 1/2" 7721-4889-S454x12 8x12 35° 102 4" 7721-4802-S454x12 8x12 35° 127 5" 7721-4827-S45
Reaming tools for cut holes / Reaming bit, R35
Flushing hole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo size No Size No Size No Size Angle mm in
2x6 2x6 1x13 16x13 35° 102 4" 7738-5602-S45
D
2-1_
538
TOP HAMMER DRILLING TOOLS • 31
Drifting and tunneling Sandvik Extra. R35 (1 3/8") bit thread
Button bit, Retrac R35
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size Size Size Angle mm in fi cation
3x6 – – 3x9 3x11 25° 54 2 1/5" HMCFAN 7738-7854-S483x6 – – 3x9 3x11 30° 54 2 1/5" MSCFAN 7738-7854-R48
2-1_
508
D
2-1_
536
Drifter rod
Drifter extension rod
Shank adapterButton bitretrac
Button bit
Reaming tools
Drifter extension rod
Dimensions Part No.L Dmm ft in mm in
2-1_
308b
R 35L
DT 35
Drifter rod, T35 - Round 39 - R35
4305 14’ 1 31/64 39 1 1/2” 7327-5243-204915 16' 1 1/2" 39 1 1/2" 7327-5249-205525 18' 1 33/64” 39 1 1/2" 7327-5255-206135 20' 1 1/2" 39 1 1/2" 7327-5261-20
Flushing hole Ø 14.5 mm.Female end OD 48,2 mm.
Drifter Extension rod, T35 - Round 39 - T35
2-1_
308c
T 35L
DT 35
3050 10' – 39 1 1/2" 7327-4731-20
Flushing hole Ø 14.5 mm.Female end OD 48,2 mm.
32 • TOP HAMMER DRILLING TOOLS
Drifting and tunneling Sandvik RT300 bits
Sandvik RT300 bits for drifting and tunneling are available in three basic designs
Type 52
Designed for hard and abrasive rock
2-1_
542
Type 53
Allround design for most types of rock
2-1_
543
Type 54
Designed for soft and less abrasive rock
2-1_
544
Non standard bitsThe products shown in this catalogue are stock standard items. Within our standard range it is possible to fi nd products suitable for
the majority of drilling conditions. Outside of this range we however undertake to manufacture non standard products to suit very
special conditions.
OptionsFollowing options are available for non standard RT300 bits for drifting and tunneling. When ordering non-standard products, a
letter that describes the option must be included in the Part No.
Example: An R32, RT300 type 53, 45mm bit with an extra hole for side fl ushing, will get the Part No.: 7733-5345A-S48.
A = One extra hole for side fl ushing
B = Two extra holes for side fl ushing
C = Grooves for front fl ushing (53 type >48mm)
D = Grooves for front fl ushing and one extra hole for side fl ushing (53 type >48mm)
E = Grooves for front fl ushing and two extra holes for side fl ushing (53 type >48mm)
F = One size smaller gauge buttons (53/54 type)
Note: If a bit has one hole for side fl ushing as standard, an A in the Part No. will give the bit one extra hole for side fl ushing, e.g. the
bit will have two holes for side fl ushing.
Options - Cemented Carbide GradesCemented carbide grade is indicated with the last letter and two digits in the Part No.
Following cemented carbide grades are available as non-standard.
S65 = Spherical DP65 buttons on 52 and 53 type
R65 = Ballistic DP65 buttons on 53 type >43mm
R55 = Ballistic DP55 buttons on 53 and 54 type >43mm
Bench drilling
Bench drilling
Page
R32 (1 1/4")....................................................................................35
T35(1 3/8") ....................................................................................37
T38 (1 1/2") ...................................................................................38
T45 (1 3/4") ....................................................................................41
T51 (2") .......................................................................................... 44
Sandvik GT60 ...............................................................................46
TOP HAMMER DRILLING TOOLS • 35
Bench drillingR32 (1 1/4")
2-1_
508
D
3x6 – 3x10 6x11 30° 51 2" HMCFVA 7733-7851-S453x6 – 3x10 6x11 30° 51 2" MSCFAN 7733-7851-R552x9 – 4x10 8x10 30° 64 2 1/2" HMCFVA 7733-7864-S45
Button bit, Retrac
2-1_
23 D
1x5 2x7.5 – – – 51 2" MSCFAN 7733-1451-421x5 2x7.5 – – – 64 2 1/2" MSCFAN 7733-1064-42
Cross bit
D
2-1_
600
3x6 − 3x8 6x10 40º 51 2" – 7733-8251-R453x6 − 4x8 6x10 40º 57 2 1/4" – 7733-8257-R45
Guide bit
1) For very short holes only.
D2-1_
486
2x9 – 6x10 8x11 35° 76 3" HMCAN 7733-2676-S45
Button bit
1)
2-1_
22
D
2x9 – 4x10 8x10 30° 64 2 1/2" HMCAN 7733-2664-S45
Button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
3x6 – 3x9 6x10 35° 51 2" HMCAN 7733-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7733-5351-R483x6 – 3x10 6x11 35° 57 2 1/4" HMCAN 7733-5357C-S48
Button bit
2-1_
316_
1
D
2-1_
487
Shank adapter
Coupling sleeve
Button bit
Button bit retrac
Cross bit
MF-rod
Extension rod
Guide tube
Extension rod
Extension rod
MF-rod
Guide bit
Coupling sleeve
Coupling sleeve
36 • TOP HAMMER DRILLING TOOLS
Bench drillingR32 (1 1/4")
L
D
2-1_
220
Coupling sleeve R32
150 – 5 29/32" 44 1 47/64" 7993-3644
MF-rod, R32 - Round 32 - R32
3050 10' – 32 1 1/4" 7853-5131-20 3660 12' – 32 1 1/4" 7853-5137-20
2-1_
276
R 32R 32L
D
Flushing hole Ø 9.2 mm. Wrench fl at 25.4 mm.Female end OD 45 mm.
L
2-1_
29
R 32 R 32D
Extension rod, R32 - Round 32 - R32
2435 8' – 32 1 1/4" 7853-3324-30 3050 10' – 32 1 1/4" 7853-3331-30 3660 12' – 32 1 1/4" 7853-3337-30
Flushing hole Ø 11.7 mm. Wrench fl at 25.4 mm.
LD R 32R 32
2-1_
425
Guide Tube
51-64 1830 6' – 46 1 3/4" 7953-4618-2051-64 3050 10' – 46 1 3/4" 7953-4631-20
Dimensions Part No. L DBit dia, mm mm ft in mm in
Female end OD 46 mm.
TOP HAMMER DRILLING TOOLS • 37
Bench drillingT35(1 3/8")
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
Button bit, Retrac T35
3x6 – 3x9 6x11 35° 54 2 1/6" MSCFAN 7517-7854-R453x6 – 3x10 6x11 35° 57 2 1/4" MSCFAN 7517-7857-R45
2-1_
508
D
MF-rod, T35 - Round 39 - T35
3050 10' 39 1 1/2" 7327-4731-203660 12' 39 1 1/2" 7327-4737-204265 14' 39 1 1/2" 7327-4743-20
Dimensions Part No.L Dmm ft mm in
2-1_
308c
T 35L
DT 35
Female end OD 48,2 mm.
2-1_
545
Button bit retrac
MF-rodShank adapter
Flushing hole Ø 14,5 mm.
38 • TOP HAMMER DRILLING TOOLS
Bench drillingT38 (1 1/2")
Button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
2x11 – 4x10 8x10 35° 64 2 1/2" MSCAN 7514-2664-R552x11 – 4x10 8x10 30° 64 2 1/2" HMCAN 7514-2664-S452x11 – 6x10 8x10 35° 70 3 3/4" HMCAN 7514-2670-S453x11 – 6x10 8x11 40° 76 3" MSCAN 7514-2676-R552x11 _ 6x10 8x10 35° 76 3" HMCAN 7514-2676-S453x10 _ 6x10 9x11 35° 89 3 1/2" HMCAN 7514-2689-S45
2-1_
322
D
2-1_
323
D
Button bit
3x7 – 3x11 6x12 30° 64 2 1/2" HMCVA 7514-3864-S453x7 – 3x11 6x12 30° 64 2 1/2" HCV 7514-3864-S65
2-1_
324
D
Button bit
3x9 – 4x11 7x12 35° 76 3" HMCVA 7514-3876-S453x9 – 4x11 7x12 35° 76 3" HMCV 7514-3876-S65
2-1_
489
D
Button bit, Drop Center
3x8 – 4x9 6x10 35° 64 2 1/2" MCAN 7514-5964-S453x8 – 4x9 6x10 40° 64 2 1/2" SCAN 7514-5964-R554x7 – 6x10 8x11 30° 76 3" MCAN 7514-5976-S454x8 – 6x10 8x11 35° 76 3" SCAN 7514-5976-R55
2-1_
490
D
Button bit, Retrac
2x11 – 4x10 8x10 30° 64 2 1/2" HMCFAN 7514-7864-S452x11 – 4x10 8x10 35° 64 2 1/2" MSCFAN 7514-7864-R55
2-1_
488
Guide tube
X-bit
Button bit Retrac
Button bit
Guide bit
Shank adapter MF-rodMF-rod
MF-rod
Coupling sleeve Extension rod Extension rod
Coupling sleeve
TOP HAMMER DRILLING TOOLS • 39
Bench drillingT38 (1 1/2")
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
Button bit, Retrac
2x11 – 6x10 8x10 35° 70 2 3/4" HMCFAN 7514-7870-S452x11 – 6x10 8x11 35° 76 3" HMCFAN 7514-7876-S452x11 – 6x10 8x11 40° 76 3" MSCFAN 7514-7876-R55
2-1_
491
D
2-1_
492
D
Button bit, Retrac, Drop Center
3x8 – 4x9 6x10 35° 64 2 1/2" MCFAN 7514-7964-S453x8 – 4x9 6x10 40° 64 2 1/2" SCFAN 7514-7964-R554x7 – 6x10 8x11 30° 76 3" MCFAN 7514-7976-S454x8 – 6x10 8x11 35° 76 3" SCFAN 7514-7976-R55
2-1_
41 D
X-bit
1x7.5 2x7.5 – – – 64 2 1/2" – 7514-4064-111x7.5 2x7.5 – – – 76 3" – 7514-4076A-11
D
2-1_
601
Guide bit
3x8 – 4x9 6x11 35° 64 2 1/2" MSCFAN 7514-8264-R45
2-1_
308
T 38L
DT 38
Flushing hole Ø 14.5 mm.Female end OD 56 mm.
MF-rod, T38 - Round 39 - T38
3050 10' – 39 1 1/2" 7324-4731-703660 12' – 39 1 1/2" 7324-4737-704265 14' – 39 1 1/2" 7324-4743-70
LD
T 38T 38
2-1_
426
Guide tube
1830 6' – 56 2 13/64" 7955-5618-203660 12' – 56 2 13/64" 7955-5637-20
Dimensions Part No.L Dmm ft in mm in
Bit dia. mm64-7664-76
Female end OD 56 mm.
40 • TOP HAMMER DRILLING TOOLS
Bench drillingT38 (1 1/2")
L
2-1
47
T 38 T 38D
Flushing hole Ø 14.5 mm. Wrench fl at 32 mm.
Extension rod, T38 - Round 39 - T38
3050 10' – 39 1 1/2" 7324-4331C-303660 12' – 39 1 1/2" 7324-4337C-30
Dimensions Part No.L Dmm ft in mm in
T38 coupling sleeve
191 – 7 1/2" 55 2 5/32" 7314-3355
L
D
2-1_
220
Flushing hole Ø 9.6 mm.
Light extension rod, T38 - Hex 32 - T38
3050 10' – 32 1 1/4" 7324-6931-20
L
2-1_
67b
T38 T 38D
TOP HAMMER DRILLING TOOLS • 41
Bench drillingT45 (1 3/4")
2-1_
494
D
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
Button bit
2x12 – 6x10 8x11 35° 76 3" HMCAN 7515-2676-S452x12 – 6x10 8x11 40° 76 3" MSCAN 7515-2676-R55
2-1_
495
D
Button bit
3x10 – 6x10 9x11 40° 89 3 1/2" MSCAN 7515-2689-R553x10 – 6x10 9x11 35° 89 3 1/2" HMCAN 7515-2689-S453x10 – 6x12 9x12 35° 102 4" HMCAN 7515-2602-S45
2-1_
324
D
Button bit
3x9 – 4x11 7x12 35° 76 3" HMCVA 7515-3876-S453x9 – 4x11 7x12 35° 76 3" HCV 7515-3876-S65
D
2-1_
496
Button bit
2x13 – 6x13 8x13 35° 89 3 1/2" HMCVA 7515-3889-S452x13 – 6x13 8x13 35° 89 3 1/2" HCV 7515-3889-S65
2-1_
497
D
Button bit, Drop Center
4x7 – 6x10 8x11 30° 76 3" MCAN 7515-5976-S454x8 – 6x10 8x11 35° 76 3" SCAN 7515-5976-R554x8 – 6x11 8x12 35° 89 3 1/2" MCAN 7515-5989-S454x8 – 6x11 8x12 40° 89 3 1/2" SCAN 7515-5989-R554x9 – 7x12 8x13 35° 102 4" MCAN 7515-5902-S454x9 – 7x12 8x13 40° 102 4" SCAN 7515-5902-R55
2-1_
491
D
Button bit, Retrac
2x12 – 6x10 8x11 35° 76 3" HMCFAN 7515-7876-S452x12 – 6x10 8x11 40° 76 3" MSCFAN 7515-7876-R55
2-1_
493b
Shank adapter
Guide bit
Button bit retrac
Button bit
MF-rod
Guide tubeCoupling sleeve
MF-rod
Extension rod
42 • TOP HAMMER DRILLING TOOLS
Bench drillingT45 (1 3/4")
Guide bit
4x8 – 5x10 8x10 35º 70 2 3/4” MSCFAN 7515-8270-R454x8 – 6x10 8x11 35º 76 3" MSCFAN 7515-8276-R454x10 – 6x11 8x12 40º 89 3 1/2" MSCFAN 7515-8289-R45D
2-1_
602
Button bit, Retrac
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
3x10 – 6x10 9x11 35° 89 3 1/2" HMCFAN 7515-7889-S453x10 – 6x10 9x11 40° 89 3 1/2" MSCFAN 7515-7889-R553x10 – 6x12 9x12 35° 102 4" HMCFAN 7515-7802-S45
2-1_
498
D
Button bit, Retrac, Drop Center
4x7 – 5x10 8x10 35° 70 2 3/4” SCFAN 7515-7970-R554x7 – 6x10 8x11 30° 76 3" MCFAN 7515-7976-S454x7 – 6x10 8x11 35° 76 3" SCFAN 7515-7976-R554x8 – 6x11 8x12 35° 89 3 1/2" MCFAN 7515-7989-S454x8 – 6x11 8x12 40° 89 3 1/2" SCFAN 7515-7989-R554x9 – 7x12 8x13 40° 102 4" SCFAN 7515-7902-R554x9 – 7x12 8x13 35° 102 4" MCFAN 7515-7902-S45
2-1_
499
D
MF-rod T45 - Round 46 - T45
3050 10' – 46 1 3/4" 7325-7731-703660 12' – 46 1 3/4" 7325-7737-704265 14' – 46 1 3/4" 7325-7743-706095 20' – 46 1 3/4" 7325-7761-70
LD
2-1
_235
T 45T 45
Flushing hole Ø 17 mm. Female end OD 63 mm.
Guide tube
Dimensions Part No.L Dmm ft in mm in
1830 6' – 63 2 1/2" 7956-6318-213660 12' – 63 2 1/2" 7956-6337-703660 12' – 76 3" 7956-7637-70
LD
T 45T 45
2-1_
427
Bit dia. mm76-8976-89
89-102
Female end OD 63 mm / 76 mm.
TOP HAMMER DRILLING TOOLS • 43
Bench drillingT45 (1 3/4")
Dimensions Part No.L Dmm ft in mm in
T45 coupling sleeve
210 – 8 1/8" 63 2 31/64" 7315-3663
L
D
T 45 T 45
2-1_
236
Extension rod T45 - Round 46 - T45
3050 10' – 46 1 3/4" 7325-7331C-303660 12' – 46 1 3/4" 7325-7337C-304265 14' – 46 1 3/4" 7325-7343C-306095 20' – 46 1 3/4" 7325-7361C-30
LT 45 T 45
2-1_
66
D
Flushing hole Ø 17 mm. Wrench fl at 38 mm.
44 • TOP HAMMER DRILLING TOOLS
2-1_
503a
Bench drillingT51 (2")
Button bit
Button bit, Retrac
Guide tube
MF- rodShank adapter
Coupling sleeve Extension rod
Coupling sleeve
Coupling sleeve
MF- rod
Extension rod
Extension rod2-
1_49
5
D
Button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
3x12 – 6x10 9x11 35° 89 3 1/2" HMCAN 7516-2689-S453x12 – 6x12 9x12 35° 102 4" HMCAN 7516-2602-S453x12 – 9x12 9x13 35° 115 4 1/2" HMCAN 7516-2615-S453x13 – 9x13 9x14 35° 127 5" HMCAN 7516-2627-S45
2-1_
497
D
Button bit, Drop Center
4x10 – 6x11 8x12 35° 89 3 1/2" MCAN 7516-5989-S454x10 – 7x11 8x12 40° 89 3 1/2" SCAN 7516-5989-R554x11 – 7x12 8x13 35° 102 4" MCAN 7516-5902-S454x11 – 7x12 8x13 40° 102 4" SCAN 7516-5902-R554x10 – 7x13 8x14 35° 115 4 1/2" MCAN 7516-5915-S454x10 – 7x14 8x14 35° 127 5” MCAN 7516-5927-S45
2-1_
498
D
Button bit, Retrac
3x12 – 6x10 9x11 35° 89 3 1/2" HMCFAN 7516-7889-S453x12 – 6x10 9x11 40° 89 3 1/2" MSCFAN 7516-7889-R553x12 – 6x12 9x12 35° 102 4" HMCFAN 7516-7802-S453x12 – 9x12 9x13 35° 115 4 1/2" HMCFVA 7516-7815-S45
2-1_
499
D
Button bit, Retrac, Drop Center
4x10 – 6x11 8x12 35° 89 3 1/2" MCFAN 7516-7989-S454x10 – 7x11 8x12 40° 89 3 1/2" SCFAN 7516-7989-R554x11 – 7x12 8x13 35° 102 4" MCFAN 7516-7902-S454x11 – 7x12 8x13 40° 102 4" SCFAN 7516-7902-R554x10 – 7x13 8x14 35° 115 4 1/2" MCFAN 7516-7915-S454x11 – 7x13 8x14 40° 115 4 1/2" SCFAN 7516-7915-R554x10 – 7x14 8x14 35° 127 5" MCFAN 7516-7927-S45
Button bit, Retrac, Flat face
3x14 – 9x11 9x11 35° 102 4" HMSCFVA 7516-4902-S453x15 – 10x12 9x14 35° 115 4 1/2" HMSCFVA 7516-4915-S453x14 – 10x13 9x14 35° 127 5" HMSCFVA 7516-4927-S45
2-1_
556a
D
TOP HAMMER DRILLING TOOLS • 45
Bench drillingT51 (2")
Coupling sleeve, T51
225 – 8 7/8" 71 2 51/64" 7316-3671225 – 8 7/8" 76 3" 7316-3676
L
D
2-1_
291a
Flushing hole Ø 21.5 mm.Female end OD 71 mm.
MF-rod, T51 - Round 52 - T51
3660 12' – 52 2" 7326-5537-704265 14' – 52 2" 7326-5543-706095 20' – 52 2" 7326-5561-70
L
2-1_
289
T 51T 51D
Extension rod, T51 - Round 52 - T51
3660 12' – 52 2" 7326-5337C-304265 14' – 52 2" 7326-5343C-306095 20' – 52 2" 7326-5361C-30
LT 51 T 51
2-1_
290
D
Flushing hole Ø 21.5 mm. Wrench fl at 45 mm.
Guide tube
Dimensions Part No.L Dmm ft in mm in
1830 6' – 76 3" 7957-7618-203660 12' – 76 3" 7957-7637-703660 12' – 87 3 1/2" 7957-8737-70
ThreadBit dia. mm
89-10289-102
102-127
LD
T 51T 51
2-1_
429
Female end OD 76 / 87 mm.
46 • TOP HAMMER DRILLING TOOLS
2-1_
548
Shank adapter Pilot tube
Button bit
Button bit, Retrac
MF- rod
Button bit, Drop Center
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
4x11 – 7x12 8x13 35° 102 4" MCAN 7620-5902-S454x11 – 7x13 8x14 35° 115 4 1/2" MCAN 7620-5915-S454x11 – 7x13 8x14 40° 115 4 1/2" SCAN 7620-5915-R554x11 – 7x14 8x14 35° 127 5" MCAN 7620-5927-S554x12 – 4x16+4x13 8x16 35° 140 5 1/2” MCAN 7620-5940-S554x12 – 4x16+4x14 8x16 35° 152 6” MCAN 7620-5952-S55
MF- rod
MF- rod
Button bit, Retrac, Drop Center
4x10 – 6x12 8x13 35° 96 3 3/4" MCFAN 7620-7996-S454x11 – 7x12 8x13 35° 102 4" MCFAN 7620-7902-S454x11 – 7x13 8x14 35° 115 4 1/2" MCFAN 7620-7915-S454x11 – 7x14 8x14 35° 127 5" MCFAN 7620-7927-S554x12 – 4x16+4x13 8x16 35° 140 5 1/2” MCFAN 7620-7940-S55
3x12 – 4x13 6x14 40° 92 3 5/8" SCFAN 7620-4792-R55
Button bit, Retrac, Drop Center
4x11 – 7x12 8x13 40° 102 4" SCFAN 7620-7902-R554x11 – 7x13 8x14 40° 115 4 1/2" SCFAN 7620-7915-R55
2-1_
500
D
D
2-1_
549b
Button bit, Flat Face, Heavy Duty
D
2-1_
496
2x14 – 6x12 8x14 35° 92 3 5/8" MCAN 7620-3892-S452x14 – 6x12 8x14 35° 96 3 3/4" MCAN 7620-3896-S453x12 – 6x12 9x14 35° 102 4" MCAN 7620-3802-S453x13 – 6x13 9x14 35° 115 4 1/2" MCAN 7620-3815-S453x13 – 6x14 9x16 35° 127 5" MCAN 7620-3827-S553x14 – 6x12 9x16 35° 140 5 1/2" MCAN 7620-3840-S55
D
2-1_
549b
Button bit, Retrac
D
2-1_
549c
2x14 – 9x12 9x12 40° 92 3 5/8" MSCFAN 7620-8792-R452x14 – 10x12 9x13 40° 102 4" MSCFAN 7620-8702-R45
Bench drillingSandvik GT60
2-1_
549d
D
TOP HAMMER DRILLING TOOLS • 47
Dimensions Part No.L Dmm ft in mm in
Pilot Tube
1600 5' 3" 87 3 1/2" 7640-8716-704265 14' – 87 3 1/2" 7640-8743-705335 17' 6" 76 3" 7640-7653-70
Female end OD 85 mm (82 mm on 76 mm tubes)
2-1_
547
GT60 GT60
LD
MF-rod, GT60 - Round 60 (64) - GT60. For bits from 96 mm.
3660 12' - 60 2 3/8" 7610-1137-704265 14' - 60 2 3/8" 7610-1143-706095 20' - 60 2 3/8" 7610-1161-704265 14' - 64 2 1/2" 7610-1243-70
Flushing hole Ø 22.5 mm. Female end OD 85 mm.
L
2-1_
546
GT60 GT60D
MF-rod, GT60 - Round 60 - GT60. For 92-115 mm bits.
4265 14' - 60 2 3/8" 7610-1443-70
Flushing hole Ø 22.6 mm. Female end OD 82 mm.
L
2-1_
546
GT60 GT60D
Button bit, Retrac, Flat Face
3x12 – 9x11 9x13 35° 102 4" HMSCFVA 7620-4902-S453x12 – 10x12 9x14 35° 115 4 1/2" HMSCFVA 7620-4915-S453x13 – 10x13 9x14 35° 127 5" HMSCFVA 7620-4927-S553x14 – 10x14 9x16 35° 140 5 1/2” HMSCFVA 7620-4940-S553x14 – 12x14 9x16 35° 152 6” HMSCFVA 7620-4952-S55
2-1_
556
D
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
D
2-1_
549d
3x13 – 6x13 9x16 35° 118 4 5/8" HMCFVA 7620-8118-S55
Bench drillingSandvik GT60
Long hole drilling
Long hole drilling underground
Page
R32 (1 1/4").....................................................................................................51
T35 (1 3/8") ....................................................................................................53
T38 (1 1/2") ....................................................................................................54
T45 (1 3/4") .....................................................................................................56
T51 (2") ............................................................................................................58
T45 (1 3/4") tube drilling tools ......................................................................60
ST58 (2 1/4") tube drilling tools ....................................................................61
ST68 (2 3/4") tube drilling tools.....................................................................62
TOP HAMMER DRILLING TOOLS • 51
Long hole drilling undergroundR32 (1 1/4")
2-1_
487
Shank adapter
Coupling sleeve
Button bit
Button bit retrac
Cross bit
MF-rod
Extension rod
Guide tube
Extension rod
Extension rod
MF-rod
Guide bit
Reaming bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
Coupling sleeve
Coupling sleeve
2-1_
508
D
3x6 – 3x10 6x11 30° 51 2" HMCFVA 7733-7851-S45
Button bit, Retrac
2-1_
23 D
1x5 2x7.5 – – – 51 2" – 7733-1451-42
Cross bit
D
2-1_
600
3x6 − 3x8 6x10 40º 51 2" MSCFAN 7733-8251-R453x6 − 4x8 6x10 40º 57 2 1/4" MSCFAN 7733-8257-R45
Guide bit
3x6 – 3x9 6x10 35° 51 2" HMCVA 7733-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7733-5351-R483x6 – 3x10 6x11 35° 57 2 1/4" HMCVA 7733-5357C-S48
Button bit
2-1_
316_
1
D
Pilot adapter
52 • TOP HAMMER DRILLING TOOLS
Long hole drilling undergroundR32 (1 1/4")
L
D
2-1_
220a
R32 coupling sleeve
150 – 5 29/32" 44 1 47/64" 7993-3644
L
2-1_
29
R 32 R 32D
Extension rod, R32 - Round 32 - R32
915 3' – 32 1 1/4" 7853-3309-20 1220 4' – 32 1 1/4" 7853-3312-20 1525 5' – 32 1 1/4" 7853-3315-20 1830 6' – 32 1 1/4" 7853-3318-20
Flushing hole Ø 11.7 mm. Wrench fl at 25.4 mm.
Dimensions Part No. L D mm ft in mm in
2-1_
127
D
4x12 8x12 35° 102 4" – 7723-4802-S45
Reaming bit
Buttons, mm Dimensions Bit Part No.Front Gauge D classi-No Size No Size Angle mm in fi cation
DT
2-1_
126
Pilot adapter for reaming of 51 mm (2") pilot holes
ThreadR32 – – – 47 1 7/8" 7823-3647
MF-rod, R32 - Round 32 - R32
915 3' – 32 1 1/4" 7853-5109-20 1220 4' – 32 1 1/4" 7853-5112-20 1525 5' – 32 1 1/4" 7853-5115-20 1830 6' – 32 1 1/4" 7853-5118-20
2-1_
276
R 32R 32L
D
Flushing hole Ø 9.2 mm. Wrench fl at 25.4 mm.Female end OD 45 mm.
Female end OD 46 mm.L
D R 32R 32
2-1_
425
Guide Tube
1830 6' – 46 1 3/4" 7953-4618-20
Dimensions Part No.L Dmm ft in mm in
TOP HAMMER DRILLING TOOLS • 53
Long hole drilling undergroundT35 (1 3/8")
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
Button bit, Retrac
3x6 – 3x9 6x11 35° 54 2 1/6" MSCFAN 7517-7854-R453x6 – 3x10 6x11 35° 57 2 1/4" MSCFAN 7517-7857-R45
2-1_
508
D
MF-rod, T35 - Round 39 - T35
1830 6' 39 1 1/2" 7327-4718-20
Dimensions Part No.L Dmm ft mm in
2-1
308c
T 35L
DT 35
Female end OD 48,2 mm.
2-1_
545
Button bit retrac
MF-rodShank adapter
54 • TOP HAMMER DRILLING TOOLS
Long hole drilling undergroundT38 (1 1/2")
2-1_
488
Guide tube
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
X-bit
Reaming bit
Button bit Retrac
Button bit
Guide bitPilotadapter
Shank adapterMF-rodMF-rod
MF-rod
Button bit
2x11 – 4x10 8x10 30° 64 2 1/2" HMCVA 7514-2664-S452x11 – 6x10 8x10 35° 70 3 3/4" HMCVA 7514-2670-S452x11 _ 6x10 8x10 35° 76 3" HMCVA 7514-2676-S45
2-1_
322
D
2-1_
323
D
Button bit
3x7 – 3x11 6x12 30° 64 2 1/2" HMCVA 7514-3864-S453x7 – 3x11 6x12 30° 64 2 1/2" HMCVA 7514-3864-S65
2-1_
324
D
Button bit
3x9 – 4x11 7x12 35° 76 3" HMCVA 7514-3876-S453x9 – 4x11 7x12 35° 76 3" HCV 7514-3876-S65
2-1_
489
D
Button bit, Drop Center
3x8 – 4x9 6x10 35° 64 2 1/2" HMCVA 7514-5964-S454x7 – 6x10 8x11 30° 76 3" HMCVA 7514-5976-S45
2-1_
490
D
Button bit, Retrac
2x11 – 4x10 8x10 30° 64 2 1/2" HMCFVA 7514-7864-S45
Button bit, Retrac
2x11 – 6x10 8x10 35° 70 2 3/4" HMCFVA 7514-7870-S452x11 – 6x10 8x11 35° 76 3" HMCFVA 7514-7876-S452x11 – 6x10 8x11 40° 76 3" MSCFAN 7514-7876-R55
2-1_
491
D
TOP HAMMER DRILLING TOOLS • 55
Long hole drilling undergroundT38 (1 1/2")
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
2-1_
41 D
X-bit
2-1_
308
T 38L
DT 38
Flushing hole Ø 14.5 mm. Female end OD 56 mm.
MF-rod, T38 - Round 39 - T38
1220 4' – 39 1 1/2" 7324-4712C-201525 5' – 39 1 1/2" 7324-4715C-201830 6' – 39 1 1/2" 7324-4718C-20
LD
T 38T 38
2-1_
426
Guide tube
1830 6' – 56 2 13/64" 7955-5618-20
Dimensions Part No.L Dmm ft in mm in
Female end OD 56 mm.
1x7.5 2x7.5 – – – 64 2 1/2" – 7514-4064-11
DT
2-1_
126
Pilot adapter for reaming of 51 mm (2") pilot holes
ThreadT38 – – 47 1 7/8" 7823-2647
2-1_
127
D
4x12 8x12 35° 102 4" – 7723-4802-S454x12 8x12 35° 127 5" – 7723-4827-S45
Reaming bit
Buttons, mm Dimensions Bit Part No.Front Gauge D classi-No Size No Size Angle mm in fi cation
2-1_
492
D
Button bit, Retrac, Drop Center
3x8 – 4x9 6x10 35° 64 2 1/2" HMCFVA 7514-7964-S453x8 – 4x9 6x10 40° 64 2 1/2" MSCFAN 7514-7964-R554x7 – 6x10 8x11 30° 76 3" HMCFVA 7514-7976-S454x8 – 6x10 8x11 35° 76 3" MSCFAN 7514-7976-R55
D
2-1_
601
Guide bit
3x8 – 4x9 6x11 35° 64 2 1/2" MSCFAN 7514-8264-R45
56 • TOP HAMMER DRILLING TOOLS
Long hole drilling undergroundT45 (1 3/4")
2-1_
493a
Shank adapter
Guide bit
Button bit retrac
Button bit
MF-rod
Guide tube
MF-rod
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
2-1_
324
D
Button bit
3x9 – 4x11 7x12 35° 76 3" HMCVA 7515-3876-S453x9 – 4x11 7x12 35° 76 3" HMCV 7515-3876-S65
2-1_
497
D
Button bit, Drop Center
4x7 – 6x10 8x11 30° 76 3" HMCVA 7515-5976-S454x8 – 6x11 8x12 35° 89 3 1/2" HMCVA 7515-5989-S45
2-1_
491
D
Button bit, Retrac
2x12 – 6x10 8x11 35° 76 3" HMCFVA 7515-7876-S45
Button bit, Retrac, Drop Center
4x7 – 6x10 8x11 30° 76 3" HMCFVA 7515-7976-S454x8 – 6x11 8x12 35° 89 3 1/2" HMCFVA 7515-7989-S45
2-1_
499
D
2-1_
494
D
Button bit
2x12 – 6x10 8x11 35° 76 3" HMCVA 7515-2676-S452x13 – 6x13 8x13 35° 89 3 1/2" HMCVA 7515-3889-S452x13 – 6x13 8x13 35° 89 3 1/2" HMCV 7515-3889-S65
Guide bit
4x8 – 5x10 8x10 35º 70 2 3/4” MSCFAN 7515-8270-R454x8 – 6x10 8x11 35º 76 3" MSCFAN 7515-8276-R454x10 – 6x11 8x12 40º 89 3 1/2" MSCFAN 7515-8289-R45D
2-1_
602
TOP HAMMER DRILLING TOOLS • 57
MF-rod T45 - Round 46 - T45
1525 5' – 46 1 3/4" 7325-7715C-201830 6' – 46 1 3/4" 7325-7718C-20
LD
2-1
_235
T 45T 45
Flushing hole Ø 17 mm. Female end OD 63 mm.
Guide tube
Dimensions Part No.L Dmm ft in mm in
1830 6' – 63 2 31/64" 7956-6318-21
LD
T 45T 45
2-1_
427
Female end OD 63 mm / 76 mm.
Long hole drilling undergroundT45 (1 3/4")
58 • TOP HAMMER DRILLING TOOLS
2-1_
503a
Long hole drilling undergroundT51 (2")
Button bit
Button bit, Retrac
Guide tube
MF- rodShank adapter
Coupling sleeve Extension rod
Coupling sleeve
Coupling sleeve
MF- rod
Extension rod
Extension rod
2-1_
495
D
Button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
3x12 – 6x10 9x11 35° 89 3 1/2" HMCVA 7516-2689-S453x12 – 6x12 9x12 35° 102 4" HMCVA 7516-2602-S45
2-1_
497
D
Button bit, Drop Center
4x10 – 6x11 8x12 35° 89 3 1/2" HMCVA 7516-5989-S454x11 – 7x12 8x13 35° 102 4" HMCVA 7516-5902-S45
2-1_
498
D
Button bit, Retrac
3x12 – 6x10 9x11 35° 89 3 1/2" HMCFVA 7516-7889-S453x12 – 6x12 9x12 35° 102 4" HMCFVA 7516-7802-S45
2-1_
499
D
Button bit, Retrac, Drop Center
4x10 – 6x11 8x12 35° 89 3 1/2" HMCFVA 7516-7989-S454x11 – 7x12 8x13 35° 102 4” HMCFVA 7516-7902-S45
Bit adapter coupling
Button bit, Retrac, Flat face
3x14 – 9x11 9x11 35° 102 4" MSCFVA 7516-4902-S45
2-1_
556a
D
TOP HAMMER DRILLING TOOLS • 59
Long hole drilling undergroundT51 (2")
Flushing hole Ø 21.5 mm.Female end OD 71 mm.
MF-rod, T51 - Round 52 - T51
1525 5’ – 52 2” 7326-5515C-201830 6' – 52 2" 7326-5518C-20
L
2-1_
289
T 51T 51D
Guide tube
Dimensions Part No.L Dmm ft in mm in
1830 6' – 76 3" 7957-7618-20
LD
T 51T 51
2-1_
429
Female end OD 76 / 87 mm.
60 • TOP HAMMER DRILLING TOOLS
Long hole drilling undergroundT45 (1 3/4") tube drilling tools
2-1_
478
Drill tube
Button bit
Shank adapter
XDC, button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
4x7.5 – 6x10 8x11 35° 76 3" HMCVA 7525-8476-R65
2-1_
477
D
L
2-1_
348
T 45 T 45
D
Drill tube, T45 - Round 65 - T45
Dimensions Part No.L Dmm ft in mm in
1525 5' – 65 2 1/2" 7985-6315-261830 6' – 65 2 1/2" 7985-6318-26
Flushing hole Ø 18 mm.
TOP HAMMER DRILLING TOOLS • 61
Long hole drilling undergroundST58 (2 1/4") tube drilling tools
2-1_
479
Shank adapter Drill tube
Button bit
Reaming bit
Button bit, Guide
XDC, button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
4x10 – 6x12 8x12 35° 89 3 1/2" HMCVA 7528-8489-R65
2-1_
477
D
Reaming bit
6X16 9X16 35° 152 6” – 7528-5652C-S65
Drill tube, ST58 - Round 76 - ST58
Dimensions Part No.L Dmm ft in mm in
1525 5' – 76 3" 7378-7615-26 1830 6' – 76 3" 7378-7618-26
Flushing hole Ø 26 mm.L
2-1_
351
ST 58 ST 58D
D
2-1_
445b
Pilot diameter 76 mm.
62 • TOP HAMMER DRILLING TOOLS
Long hole drilling undergroundST68 (2 3/4") tube drilling tools
2-1_
484a
Shank adapter Drill tube
Button bit
Reaming bit
Button bit, Guide
XDC, button bit
Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation
4x10 – 8x12 10x12 35° 102 4" HMCVA 7529-8402-R654x10 – 8x14 10x14 35° 115 4 1/2" HMCVA 7529-8415-R65
2-1_
483
D
2-1_
451
D
Button bit, Heavy Duty2x15 – 6x14 8x14 35° 102 4" HCV 7529-6902-S65
2-1_
482
D
XDC, button bit, Guide4x10 – 8x12 10x12 35° 102 4" HMCVA 7529-7302-R654x10 – 8x14 10x14 35° 115 4 1/2" HMCVA 7529-7315-R65
Collaring bit
2-1_
357C
D
3x18 – 8x16 9x16 35° 152 6" – 7529-6652-S45
Drill tube, ST68 - Round 87 - ST68
1525 5' – 87 3 1/2" 7379-8715-261525 5' – 87 3 1/2" 7379-8715-46 1)
1830 6' – 87 3 1/2" 7379-8718-26
L
2-1_
352
ST 68 ST 68D
Dimensions Part No.L Dmm ft in mm in
FLushing hole Ø 30 mm.1) Permanent back fl ow valve.
D
2-1_
445a
Reaming bit
6x16 9x16 35° 152 6” – 7529-5652C-S65
Pilot diameter 95 mm.
Rock reinforcement
Rock reinforcement
Page
Sandvik RX300 expandable rock bolts ..........................................................66
High pressure water pumps ...........................................................................69
Installation arm for RX300 bolts .................................................................70
Cleaning lance & Pull tester ............................................................................71
TOP HAMMER DRILLING TOOLS • 65
Rock reinforcement
Sandvik RX 300 product range
The Sandvik RX300 Expandable Rock Bolts are available in two basic qualities, simply called the ERB-line and the ERB
Plus-line. Each of them including products with three load capacity variants – 120 kN, 160 kN and 240 kN.
The main difference between the two qualities is elongation characteristics. The ERB Plus-line is made of a “softer”
steel quality and has gone through an annealing process. Due to this it can be stretched longer and more even
before breaking compared to the standard ERB-line quality. This gives the ERB Plus-line better capacity to follow rock
deformation and is for that reason better suited for rock conditions with squeezing ground or high strain concentrations
areas. The standard ERB-line quality is suitable for most other applications.
Corrosion protection and coating
The steel grades used for manufacturing of RX 300 bolts are not corrosion protected, meaning that during overseas
transportation and long storage time the bolts may be corroded. Normally this does not affect the product quality.
For overseas transportation and long storage time the bolts can be coated with an anti-corrosive agent. This will prevent
corrosion during transport and storage but not after bolt installation.
In very corrosive conditions or for increased service life, the bolts can be covered with Corrolastic Expander Paint. This
will prevent corrosion also after bolt installation.
Part No Key
7970-xxxx-xx
0 No corrosion protection
1 With anti-corrosive agent
2 With Corrolastic Expander Paint
1 ERB Standard
2 ERB Plus (+)
Length of the bolt in mm
66 • TOP HAMMER DRILLING TOOLS
Rock reinforcementSandvik RX300 expandable rock bolts
Face plate for ERB 120
ERB 120 / 120+
Length Weight Part No.Lmm kg
600 1,20 7970-600-xx
900 1,80 7970-900-xx
1.200 2,40 7970-1200-xx
1.500 3,00 7970-1500-xx
1.600 3,20 7970-1600-xx
1.800 3,60 7970-1800-xx
2.000 4,00 7970-2000-xx
2.100 4,20 7970-2100-xx
2.400 4,80 7970-2400-xx
2.700 5,40 7970-2700-xx
3.000 6,00 7970-3000-xx
3.300 6,60 7970-3300-xx
3.600 7,20 7970-3600-xx
4.000 8,00 7970-4000-xx
4.500 9,00 7970-4500-xx
5.000 10,00 7970-5000-xx
5.500 11,00 7970-5500-xx
6.000 12,00 7970-6000-xx
L
8-1_
107
Dimensions Weight Part No.
mm kg
Flat 150 x 150 x 6 1,08 7970-P156 Flat 150 x 150 x 8 1,44 7970-P158
Steel grade ST37
Flat
Domed 150 x 150 x 4 0,66 7970-P154D
Steel grade ST37
Domed
8-1_
107b
ERB 120 ERB 120+
Tube thickness 2 mm 2 mm
Bolt diameter 28 mm 28 mm
Original tube diameter 41 mm 41 mm
Profi le diameter 27.5 mm 27.5 mm
Bushing head diameter 30/36 mm 30/36 mm
Upper bushing diameter 28 mm 28 mm
Hole diameter 32 - 39 mm 32 - 39 mm
Optimal hole diameter 35 - 38 mm 35 - 38 mm
Breaking load 120 kN 120 kN
Minimum elongation 10 % 20 %
Typical elongation up to 30 %
TOP HAMMER DRILLING TOOLS • 67
8-1_
107
Rock reinforcementSandvik RX300 expandable rock bolts
Face plate for ERB 160
ERB 160 / 160+
Length Weight Part No. L mm kg
1.800 5,22 7972-1800-xx
2.100 6,09 7972-2100-xx
2.400 6,96 7972-2400-xx
2.700 7,83 7972-2700-xx
3.000 8,70 7972-3000-xx
3.300 9,57 7972-3300-xx
3.600 10,44 7972-3600-xx
4.000 11,60 7972-4000-xx
4.500 13,05 7972-4500-xx
5.000 14,50 7972-5000-xx
5.500 15,95 7972-5500-xx
6.000 17,40 7972-6000-xx
L
8-1_
106
ERB 160 ERB 160+
Tube thickness 2 mm 2 mm
Bolt diameter 38 mm 38 mm
Original tube diameter 54 mm 54 mm
Profi le diameter 36 mm 36 mm
Bushing head diameter 41/48 mm 41/48 mm
Upper bushing diameter 38 mm 38 mm
Hole diameter 43 - 52 mm 43 - 52 mm
Optimal hole diameter 45 - 51 mm 45 - 51 mm
Breaking load 160 kN 160 kN
Minimum elongation 10 % 20 %
Typical elongation up to 30 %
Steel grade ST37
Dimensions Weight Part No.
mm kg
Flat 150 x 150 x 6 1,08 7971-P156 Flat 150 x 150 x 8 1,44 7971-P158
Domed 150 x 150 x 4 0,66 7971-P154D
Steel grade ST37
Domed
8-1_
107b
Flat
68 • TOP HAMMER DRILLING TOOLS
Rock reinforcementSandvik RX300 expandable rock bolts
ERB 240 / 240+
Length Weight Part No.L mm kg
1.800 7,20 7971-1800-xx
2.100 8,40 7971-2100-xx
2.400 9,60 7971-2400-xx
2.700 10,80 7971-2700-xx
3.000 12,00 7971-3000-xx
3.300 13,20 7971-3300-xx
3.600 14,40 7971-3600-xx
4.000 16,00 7971-4000-xx
4.500 18,00 7971-4500-xx
5.000 20,00 7971-5000-xx
5.500 22,00 7971-5500-xx
6.000 24,00 7971-6000-xx
L
8-1_
106
8-1_
107
Face plate for ERB 240
Steel grade ST37
Dimensions Weight Part No.
mm kg
Flat 150 x 150 x 6 1,08 7971-P156 Flat 150 x 150 x 8 1,44 7971-P158
Domed 150 x 150 x 4 0,66 7971-P154D
Steel grade ST37
Domed
8-1_
107b
Flat
ERB 240 ERB 240+
Tube thickness 3 mm 3 mm
Bolt diameter 38 mm 38 mm
Original tube diameter 54 mm 54 mm
Profi le diameter 36 mm 36 mm
Bushing head diameter 41/48 mm 41/48 mm
Upper bushing diameter 38 mm 38 mm
Hole diameter 43 - 52 mm 43 - 52 mm
Optimal hole diameter 45 - 51 mm 45 - 51 mm
Breaking load 240 kN 240 kN
Minimum elongation 10 % 20 %
Typical elongation up to 30 %
TOP HAMMER DRILLING TOOLS • 69
Rock reinforcementHigh pressure water pumps
RX520E high pressure water pump for RX300 bolts
Electric high-pressure water pump for installation of RX300
expandable rock bolts
Complete pump unit 790-4200
Spare Parts and Accessories
Water fi lter 60μ 791-4101Repair Kit 3 Sealings 791-4102Repair Kit 10 Valves 791-4103High-pressure hose DN 10, 300 bar, 10 meter 791-4105
Part No.
Technical data
Maximum output ................. 21 l/min.
Maximum output ............... 1.260 l/h
Operating pressure, up to . 320 bar
Maximum working pressure 300 bar
Electricity supply ................. 32A / 400V
Rpm of the pump ............... 400 rpm
Current consumption ......... 25 A
Dimensions (LxWxH) ........ 700mm x 550mm x 620mm
Weight ............................... 76 kg
Dimension of nozzle .......... 055
Protection of splash proof . IP 55
8-1_109
RX510H - 510E high pressure water pump for RX300 bolts
Hydraulic/Electric water pump for installation of RX300 expandable
rock bolts
Complete pump unit
RX510H 790-3100
RX510E 790-4100
Spare Parts and Accessories
Water fi lter 60μ 791-4101
Repair Kit 3 Sealings 791-4102
Repair Kit 10 Valves 791-4103
High-pressure hose DN 10, 300 bar,
10 meter 791-4105
Technical data RX510H RX510E
Maximum output ................. 14 l/min 14 l/min
Maximum output ................. 840 l/h bar 840 l/h bar
Operating pressure ............ 320 bar 320 bar
Maximum working pressure 300 bar 300 bar
Normal Voltage .................. 2 • 12 V (24V) 400V
Driving effi ciency .............. 7,5 kW 7,5 kW
Rpm of the pump ............... 1400 1400
Oil pressure ....................... 170 - 200 bar
Oil quantity ........................ max 40 l/min
Amperage .......................... 16A
Dimensions in mm (L•W•H) 670•350•515 670•350•515
Approx. weight .................. 52 kg 42 kg
Nozzle dimension .............. 040 040
Recoil ................................ 66 N 66 N
Protection of splash proof . IP 55 IP 55
8-1_115
70 • TOP HAMMER DRILLING TOOLS
Rock reinforcementHigh pressure water pumps & Installation arm
RX500P high pressure water pump for RX300 bolts
Pneumatic high-pressure water pump for installation of RX300
expandable rock bolts
Complete pump unit 790-1100
Spare Parts and Accessories
Water fi lter 60μ 791-4101
Repair Kit 3 Sealings 791-4102
Repair Kit 10 Valves 791-4103
High-pressure hose DN 10, 300 bar,
10 meter 791-4105
Technical data
Pump type ............................ Pneumatic
Working pressure, water ... 320 bar
Max output fl ow, water ...... 9 l/min, 540 l/h
Press. amplifi cation (air-water) 64 times
Input air pressure................ 5-8 bar
Air consumption (5 bar) ..... 50-60 l/s
Input water pressure ......... 3-10 bar
Stroke volume, water ........ 50 cm3
Dimensions (LxWxH) ........ 720mm x 375mm x 360mm
Weight ............................... 34 kg
8-1_117
Part No.
Installation arm for RX300 bolts
High-pressure installation arm for RX300 expandable rock bolts.
All vital components are specially selected to withstand peak
pressures up to 500 bar.
Installation Arm with nozzle head,
ERB 120/120+ incl. 10 m high pressure hose
790-2100
Installation Arm with nozzle head,
ERB 160/160+ and 240/240+
incl. 10 m high-pressure hose 790-2200
High–pressure hose DN, 300 bar,
10 meters 791-4105
8-1_116
TOP HAMMER DRILLING TOOLS • 71
Cleaning lance for Sandvik high pressure water pumps
The high-pressure water pumps RX510E, RX510H and RX520E
for installation of Sandvik RX300 expandable rock bolts are also
suitable for cleaning of vehicles such as loaders and drilling
jumbos, if this cleaning lance is used.
High-pressure cleaning lance 790-2300High-pressure hose DN, 300 bar,10 meters 791-4105
8-1_118
Pull tester equipment for RX300 bolts
Hydralic pull tester for RX300 bolts, with digital pressure gauge.
Complete pull tester 790-6100
8-1_119
Rock reinforcementCleaning lance & Pull tester
Part No.
Shank adapters
Shank adapters
ROCK DRILL CATEGORIES
BE = bench drillingBO = boltingDS = dimensional stone drillingPD = production drilling underground (long hole drilling)TU = drifting and tunneling
Page
Shank rods ..................................................................................... 75
Atlas Copco ................................................................................... 76
Boart .............................................................................................. 79
Furukawa ....................................................................................... 80
Gardner-Denver, Ingersoll-Rand and Klemm ............................. 81
Montabert ..................................................................................... 82
SIG .................................................................................................. 83
Sandvik ........................................................................................... 84
Secoma and Toyo .......................................................................... 89
TOP HAMMER DRILLING TOOLS • 75
Shank rods
L
3-1_
15
22
108
4.5-5.0 R22 255 7801-6103-134.5-5.0 R23 255 7807-6103-11*4.5-5.0 R25 255 7802-6103-13
For hexagonal bushing 22 x 108 mm
Dimensions, mm Part No.
Flushing tube Thread L
Flushing hole Ø 6.7 mm.
L
3-1_
17
108
25
For hexagonal bushing 25 x 108 mm
4.5-5.0 R23 255 7807-7103-11*4.5-5.0 R25 255 7802-7103-14
Flushing hole Ø 8.6 mm.
L
3-1
22
159
25
For hexagonal bushing 25 x 159
8 R25 255 7802-7503-20
* No packing. Not suitable for hydraulic machines with water fl ushing.
Flushing hole Ø 8.6 mm.
76 • TOP HAMMER DRILLING TOOLS
Shank adaptersAtlas Copco
L
3-1_
29
32 25.4
57.238.1
Atlas Copco BBC 51, 52, 54 and 120
TU 10 R32 380 7803-4200-30TU 10 T38 390 7304-4200-30
3-1_
31
L
64.4
13.480
44.644.4
Atlas Copco BBE 57
BE 14 T38 537 7304-7502-60
20.5
4831.7
19 L3-
1_26
32
Atlas Copco BBC 43, 44, 45 and 100
TU 10 R32 380 7803-3100-30
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
Atlas Copco COP 125, 130 and 131
TU,BE,PD 14 T38 380 7304-4500-60
L
52
32
3-1_
12
38.1 38.7
Atlas Copco COP 1032 HD
TU,BO – R32 340 7803-3588-01
L58
9
54
3-1_
120
34 45
L58
9
54
3-1_
120b
34 55 TU,BO – R38 340 7804-3575-01
Atlas Copco COP 1032
BE – T35 550 7307-3576-01
L58.5
44.9
53.9
8.8
3-1_
242
33.9
TOP HAMMER DRILLING TOOLS • 77
Dimensions, mm Part No.Hammercategory Flushing hole Thread L
74L 9
54
3-1_
12334 38
Atlas Copco COP 1036/1038 HB
BE – R32 500 7803-3591-01BE – T38 500 7304-3591-01
74L 9
54
3-1_
123b34 45 BE – T45 500 7305-3591-01
3-1_
124
L74 9
54
34 38
Atlas Copco COP 1038 HD/1238
TU – R32 485 7803-3590-03TU – R38 485 7804-3590-03TU – T38 485 7304-3590-03
Shank adaptersAtlas Copco
58 9
54
3-1_
122
L
34 45
Atlas Copco COP 1032 LE
BE,DS – R32 550 7803-3576-01
74 9
54
L
3-1_
125
34 38
Atlas Copco COP 1038 HL
BE,PD – R32 575 7803-3593-01BE,PD – T38 575 7304-3593-01
74 9
54
L
3-1_
125b
34 45 BE,PD – T45 575 7305-3593-01
78 • TOP HAMMER DRILLING TOOLS
Shank adaptersAtlas Copco
Atlas Copco COP 1238
74L 9
54
3-1_
12334 38 BE – R32 500 7803-3591-01
BE – T38 500 7304-3591-01TU – R38 485 7804-3590-03TU – T38 485 7304-3590-03
Dimensions, mm Part No.Hammercategoty Flushing tube Thread L
74L 9
54
3-1_
123b34 45 BE – T45 500 7305-3591-01
L9
54
3-1_
173b
38
74
34BE,PD – R32 575 7803-3593-01BE,PD – T35 575 7307-3593-01BE,PD – T38 575 7304-3593-01
3-1_
174b
34
74L
54
9
45BE,PD – T38 575 7304-3550-01BE,PD – T45 575 7305-3593-01
9
54
3-1_
204A
84.5
55
L
Atlas Copco COP 1432 Female
TU – R38 341 7804-3670-02TU – R32 341 7803-3670-02
9
54
3-1_
127A
L84.5
38 BO – R32 525 7803-3656-01BE T35 525 7307-3656-01BO – T38 525 7304-3656-01
9
54
3-1_
127
L84.5
38
Atlas Copco COP 1432, COP 1532, COP1440, COP1838 HD/ME
TU – R38 435 7804-3652-01TU – T35 435 7307-3652-01TU – T38 435 7304-3652-01 TU – R32 435 7803-3652-01
TOP HAMMER DRILLING TOOLS • 79
Shank adaptersAtlas Copco and Boart
54
52
125L
3-1_
205
10
Atlas Copco COP 1840 HE, COP 1850
BE,PD – T45 565 7305-3690-02BE,PD – T51 565 7306-3690-03
Atlas Copco COP 4050 EX
PD – ST68 805 7329-3716-01
136
68
70
L
3-1_
203
11.2
3-1_
171
L
52
84.5 9
54
Atlas Copco COP 1550, COP 1838 ME/ HE
BE,PD – T38 525 7304-3655-01BE,PD – T45 525 7305-3655-01BE,PD – T51 525 7306-3655-02
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
L
66.1
15.0
3-1_
67
64
38.1 45
Boart HD 125, HD 150, HD 160
TU – R38 495 7804-4993-01TU – T38 495 7304-4993-01
Atlas Copco COP 1550 EX, COP 1838 EX
BE – T38 730 7304-3825-02BE – T45 730 7305-3826-02
Atlas Copco COP 2150 PG
BE – T51 770 7306-3692-01
L
59.8
94
53.9
8.8
3-1_
240
53.4
8.8L124.5
51.9
3-1_
241
67.95
11.3L
112
3-1_
249
90
Atlas Copco COP 4050 MUX
PD – ST68 835 7329-3720-01
80 • TOP HAMMER DRILLING TOOLS
Shank adaptersFurukawa
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
L
71
21
3-1_
139
69
44.2 44
Furukawa PD 200R
BE 14 T38 484 7304-7581-60
64.4
13.6
3-1_
104
L79
44.3 45
Furukawa HD 260, HD 300
BE 16 T38 655 7304-7526-80BE 16 T45 655 7305-7526-80
75
35.7 44.8
3-1_
182
56.9
9.9L
Furukawa HD 609
BE – T38 620 7304-4791-01BE – T38 690 7304-4780-01BE – T45 620 7305-4791-01
L64
3-1_
43
55.5
18.2
44.5 44.3
Furukawa M 120 and PD 200
BE 14 R32 330 7803-7500-61BE 14 R38 350 7804-7500-60BE 14 T38 380 7304-7543-60BE 14 T38 446 7304-7500-60
Furukawa HD 612
BE – T45 710 7305-7414-01
89
41.7 50.8
3-1_
182b
64.9
11.75L
Furukawa HD 709
BE – T38 620 7304-7426-01
BE – T45 788 7305-7417-01
3-1_
244
L93
44.9
83
10
3-1_
243
71.8
12.3L99.5
50.8
Furukawa HD 712
TOP HAMMER DRILLING TOOLS • 81
Shank adaptersGardner-Denver, Ingersoll-Rand and Klemm
Gardner-Denver PR 123
TU,BE 14 R32 330 7803-7500-61TU,BE 14 R38 350 7804-7500-60TU,BE 14 T38 446 7304-7500-60TU,BE 14 T38 380 7304-7543-60
L64
3-1_
43
55.5
18.2
44.5 44.3
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
Ingersoll-Rand URD 475, URD 550, VL120, EVL 130, VL140 and F16
BE 14 R32 330 7803-7500-61BE 14 R38 350 7804-7500-60BE 14 T38 380 7304-7543-60BE 14 T38 446 7304-7500-60
L
64
3-1_
43
55.5
18.2
44.5 44.3
Klemm 4053
8.5
3-1_
214
56.5
74
L154
56.3 BE – R55 500 7805-6015 1)
BE – R55 500 7805-7015 2)
1) LH-Rotation 2) RH-Rotation
Ingersoll-Rand YH 65, YH 80
45
L85
3-1_
135
64.3
13.546
BE 19 T38 495 7304-7525-19BE 19 T45 500 7305-7525-19
Ingersoll-Rand YH 65 RP, YH 70 RP, YH 75 RP, YH 80 RP
BE 19 T45 700 7305-7546-19
119
L
46 45
3-1_
138b
64.8
13.5
82 • TOP HAMMER DRILLING TOOLS
Shank adaptersMontabert
Montabert HC40 (female)
TU, BO – R32 270 7803-4726-01
Montabert HC40
BE – R32 447 7803-4725-01 BE – R38 447 7804-4725-01
L58
3-1_
82 52.7
8.4
38.1
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
Montabert HC 80, HC 90, HC 105
L
52.73-1_
71
978.4
38.1TU – T38 440 7304-4720-01TU – T38 500 7304-4723-01
Montabert H 100
3-1_
31
L
64.4
13.480
44.644.4 BE 14 T38 537 7304-7502-60
3-1_
245
L58
52.6
52.6
8.4
TOP HAMMER DRILLING TOOLS • 83
Shank adaptersMontabert and SIG
Montabert HC 80R, HC 120R, HC 150R
BE – T51 670 7306-7528-02
9.4102
L
513-
1_10
859.7
Montabert HC 120, HC 150
BE – T45 490 7305-7520-01
9.4
59.7
3-1_
140
95L
45
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
SIG HBM 50, 100 and 120
L58
9
54
3-1_
120
34 45 BO – R32 340 7803-3588-01
SIG HBM 100 and 120
L58
9
54
3-1_
120b
34 55 TU, BO – R38 340 7804-3575-01
SIG HBM 50, 100 and 120
58 9
54
3-1_
122
L
34 45 BE, DS – R32 550 7803-3576-01
SIG 101
74L 9
54
3-1_
12334 38 BE – R32 500 7803-3591-01
Montabert HC 200A
BE – T51 840 7306-7530-02BE – GT60 840 7600-7530-02
11.4138
L
60
3-1_
232
73
84 • TOP HAMMER DRILLING TOOLS
Shank adaptersSandvik
HL 300S
BO,TU – R28 245 7809-7547-01BO,TU – R32 245 7803-7547-01
10
58.8
L39
3-1_
142
45
HL 300
BE – R32 400 7803-7549-01
10
58.8
39L
3-1_
141
32
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
L400, L410, L500, L510, L550
L
3-1_
58
20 20.5
4831.7 32
BO, PD, TU 10 R32 380 7803-3602-30
HLR 438L and HLR 438T
L
3-1_
55
37
57
25.7
38 38 BE, TU 12.7 R32 380 7803-4700-50BE, TU 12.7 T38 400 7304-4700-50
HLR 438LS, 438TS, HL 538, HL538L, L550S
L
3-1_
57
37
57
25.7
38 38BE, PD, TU – R32 450 7803-4700-01 BE, PD, TU – R38 450 7804-4700-01BE, PD, TU – T38 455 7304-4700-01BE – T38 545 7304-4706-01
-38 = For 38 mm front head, S=For underground drilling
HLX 3
BO,TU – R32 324 7803-7662-01
HLX 3 F
BO,TU – R32 205 7803-7663-01
58.75
7.9
3-1_
246
L53
44.85
L53
44.85
58.75
7.9
3-1_
247
TOP HAMMER DRILLING TOOLS • 85
HL 500-38 / 510-38
BE – R32 550 7803-7535-02BE – T35 550 7307-7535-02BE – T38 550 7304-7535-02
10
58.8
49L
3-1_
131
38
HL 500-45 / 510-45
10
58.8
45L
3-1_
168
49
BE – R32 550 7803-7557-01BE – T35 550 7307-7557-01BE – T38 550 7304-7557-01BE – T45 550 7305-7557-01
Shank adaptersSandvik
HL 500 F / 510 F
BO – R32 350 7803-7553-01
10
58.8
3-1_
183
58
45
L
HL 500 S-38 / 510 S-38 / 510 B / 510 LH
PD,TU – R32 460 7803-7531-01PD,TU – R38 460 7804-7531-01PD,TU – T38 460 7304-7531-01PD,TU – R38 500 7804-7536-01PD,TU – T38 500 7304-7536-01
10
58.8
49L
3-1_
144
38
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
HL 550 SUPER / 560 SUPER / 510 S-45
49
45
L
3-1_
184
10
58.8
PD,TU – T35 550 7307-7557-01TU – R38 500 7804-7554-01TU – T38 500 7304-7554-01
HLX 5 / HLX 5T
49
45
L
3-1_
212
7.9
58.7
TU – R32 500 7803-7585-01TU – T35 500 7307-7585-01TU – T38 500 7304-7585-01TU – R38 500 7804-7585-01BE – R32 575 7803-7586-01BE – T35 575 7307-7586-01BE – T38 575 7304-7586-01BE – T45 575 7305-7586-01
-38, -45 = For 38 or 45 mm front head, S=For underground drilling
HLX5 PE-45
3-1_
248
58.7
9.9L126
45
TU – R32 575 7803-7664-01TU – T38 575 7304-7664-01
86 • TOP HAMMER DRILLING TOOLS
Shank adaptersSandvik
HL 645
BE – T38 600 7304-7541-02BE – T45 600 7305-7541-02
L
59
68
3-1_
109
4543.8
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
HL 650-45 / 700-45 / 700T-45 / 710-45 / 800T-45
69
12.9
3-1_196
45
L95
BE – T38 600 7304-7576-01BE – T45 600 7305-7576-01
HL 650-52, 700-52 / PE-52 / S-52, 710-52 / S-52 / PE-52 / SPE-52, 800T-52 / PE-52
69
12.9
3-1_196B
52
L95
BE,PD – T38 600 7304-7577-02BE – T45 600 7305-7577-02BE – T51 600 7306-7577-03
HL 600-45 / 600 S-45
L75
3-1_
132
60
39.8 45
10
BE – R32 600 7803-7532-01BE – T38 600 7304-7532-01Tubes, BE – T45 600 7305-7532-01TU,PD – T38 525 7304-7537-01TU,PD – T45 525 7305-7537-01
HL 600-523-
1_17
2
L5275
10
60
39.8 BE – T45 650 7305-7551-01BE – T51 650 7306-7551-02
-45, -52 = For 45 or 52 mm front head, PE= For Power Extractor rock drill (reverse hammering), S=For underground drilling
HL 850S
BE, PD – T45 670 7305-7400-01
80
3-1_
111
69
L 14
47.4 52
TOP HAMMER DRILLING TOOLS • 87
Shank adaptersSandvik
HL 1000-52 / 1000 S-52
L
79
14
3-1_
133
75
52 BE – T45 670 7305-6010-01BE – T51 670 7306-6010-02PD T45 590 7305-6008-01PD T51 590 7306-6008-01
HL 1000-60
L
79
14
3-1_
133B
75
60BE – T51 670 7306-6014-02BE – GT60 670 7600-6014-02
HL 1000 S-80 Tube drilling
80L
79
14
3-1_
166
75
PD – ST58 635 7328-6009-02PD – ST68 640 7329-6009-02
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
HL 1000 PE-52
52
L136
3-1_
186
79
14
BE – T51 840 7306-6019-02*
* suited only for early drills with the long type of Power Extractor with 52 mm bearing diameter
-52, -60, -65, -80 = For 52, 60, 65 or 80 mm front head, PE= For Power Extractor rock drill (reverse hammering), S=For underground drilling
HL 1000-80, Shoulder drive
80L
79
14
3-1_
166
75
BE – GT60 670 7600-6031-01
BE – T51 760 7306-6025-02BE – GT60 760 7600-6025-02
HL 1000 PE-65 / HL 1500 PE-65 / HL 1560 T-65
65
L111
3-1_215
79
14
88 • TOP HAMMER DRILLING TOOLS
Shank adaptersSandvik
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
HL 1500 S-80 Tube drilling
PD – ST58 635 7328-6020-01PD – ST68 635 7329-6020-01
79
14
80
L111.5
3-1_
199
HL 1500 T-80, Shoulder drive
HL 1500-52 / 1500 T-52
BE – T51 710 7306-6021-0252
L111.5
3-1_
194
79
14
HL 1500-60 / 1500 T-60
BE – T51 760 7306-6022-02BE – GT60 760 7600-6022-0360
L111.5
3-1_
194B
79
14
BE – GT60 760 7600-6030-01
HL 1500 SPE-90 Tube drilling
PD – ST58 635 7328-6035-01PD – ST68 635 7329-6035-01
L111
3-1_215b
79
14
90
-52, -60, -65, -80, -90 = For 52, 60, 65, 80 and 90 mm front head, PE= For Power Extractor rock drill, S=For underground drilling, T= Drill with stabilizer
79
14
80
L111.5
3-1_
199
TOP HAMMER DRILLING TOOLS • 89
Secoma Hydrastar 200, 300 and X2
TU – R32 485 7803-3590-03TU – R38 485 7804-3590-03TU – T38 485 7304-3590-03
L
3-1_
40
74
54
9
34 38
Shank adaptersSecoma and Toyo
Secoma Hydrastar 200
TU,BO – R32 351 7803-4703-01
3-1_
130
90L
34 45
54
9
Dimensions, mm Part No.Hammercategory Flushing tube Thread L
Secoma Hydrastar 350
74L 9
54
3-1_
123
34 38 BE – R32 500 7803-3591-01TU – R38 485 7804-3590-03BE – T38 500 7304-3591-01
Toyo PR 220
L64
3-1_
43
55.5
18.2
44.5 44.3 BE 14 R32 330 7803-7500-61BE 14 R38 350 7804-7500-60BE 14 T38 446 7304-7500-60
Toyo TH 501
BE 11 T38 565 7304-7583-40
3-1_
31b
L
64.2
1368
44.944.2
Grinding
Grinding
Page
Button bit grinder RG400 and RG410 ........................................93
Button bit grinder RG420P ..........................................................94
Button bit grinder RG420H .........................................................95
Button bit grinder RG420E ..........................................................96
Button bit grinder RG420P/H/E Manual ....................................97
Button bit grinder RG440 ............................................................98
Button bit grinder RG460 ............................................................99
Bit blaster RG500 .......................................................................100
Cross bit grinder RG300 ............................................................101
Cross bit grinder RG320 ............................................................102
Cross bit grinder RG340 ............................................................103
Cross bit grinder RG360 ............................................................104
Integral steel grinder RG100P ....................................................105
Integral steel grinder RG100H ...................................................106
Integral steel grinder RG120E ...................................................107
Integral steel grinder RG140P/H ...............................................108
Grinding cups ..............................................................................109
Grinding wheels ..........................................................................110
Grinding accessories .................................................................. 112
TOP HAMMER DRILLING TOOLS • 93
Grinding Button bit grinder RG400 and RG410
RG410
Intended for grinding all kinds of button bits
Complete grinder 796-5100
Accessories optionalIn line oiler 797-5747-50Tools for O-ring replacement 797-5452Cooling/tank unit, complete 797-5488-85Grinding gauge for button up to Ø 16 mm 795-1396Grinding cups See page 109
Recommended lubricantsAir tool oil, 1 litre 797-5870-90
8-1_53b
Part No.
Technical data
Air pressure .................................. 6-8 barAir consumption ........................... 40-55 l/sSpindle speed ............................... 19000 r.p.m.Flushing air pressure ................... Max. 6 barFlushing water pressure .............. Max. 6 barWater consumption ...................... 5-6 l/minHose connections:Air, air hose ................................... 12.5 mm (1/2") ID Water, water hose ........................ 6.3 mm (1/4") IDDimensions: HxWxD mm .............. 150x450x130 Weight, without package and hose 2.9 kgWeight, with package and hose ... 3.5 kg
RG400
Technical data
Air pressure .................................. 6-8 barAir consumption ........................... 16-17 l/sSpindle speed ............................... 14000 r.p.m.Flushing air pressure ................... Max. 6 barFlushing water pressure .............. Max. 6 barWater consumption ...................... 5-6 l/minHose connections:Air, air hose ................................... 12.5 mm (1/2") ID Water, water hose ........................ 6.3 mm (1/4") IDDimensions: HxWxD mm .............. 150x450x130 Weight, without package and hose 2.9 kgWeight, with package and hose ... 3.5 kg
8-1_53b
Intended for grinding all kinds of button bits(Max. button size 10 mm)
Complete grinder 796-5116
Accessories optionalIn line oiler 797-5747-50Tools for O-ring replacement 797-5452Cooling/tank unit, complete 797-5488-85Grinding gauge for button up to Ø 16 mm 795-1396Grinding cups See page 109
Recommended lubricantsAir tool oil, 1 litre 797-5870-90
94 • TOP HAMMER DRILLING TOOLS
GrindingButton bit grinder RG420P
RG420P
Technical data
Air pressure ................................. Max. 13 bar/ Min. 6.5 barAir consumption ........................... 40-60 l/secWater pressure ............................ Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Rated power (motor) ..................... 1.7 kWElectricity supply .......................... 24V DC, 5ACoolant/fl ushing medium ............. WaterAir connection, air hose ............... 20 mm (3/4") IDWater connection, water hose ..... 9.5 mm (3/8") ID Dimensions: HxWxD mm .............. 730x350x300Weight .......................................... 43.5 kg
* With cooling tank unit 0,2-0,3 l/min.
Part No.
Intended for grinding all kinds of button bit.It is capable of handling threaded and taperedbutton bits upp to Ø 127 mm and DTH button bits up to Ø 250 mm (max. shank Ø 130 mm).
Pneumatic grinder without cooling unit 796-6205
Pneumatic grinder with cooling unit 796-6206
Accessories optionalBit holder insert for retrac-bits compl. 797-5502-50Guard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-locking system, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete, 10 l 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109
Complete grinding head 797-5130-10
Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10Air tool oil, 1 liter 797-5870-90
8-1_
900
TOP HAMMER DRILLING TOOLS • 95
GrindingButton bit grinder RG420H
RG420H
Technical data
Hydraulic pressure ...................... Max. 200 bar/ Min. 140 bar
Hydraulic-oil fl ow consumption ... 12 l/minAir pressure ................................. Max. 13 bar/ Min. 4 barAir consumption ........................... 5-6 l/secWater pressure ............................ Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Rated power (motor) ..................... 3.0 kWElectricity supply .......................... 24V DC, 5ACoolant/fl ushing medium ............. WaterHydraulic connection, hydr. hose . R 3/8" female threadAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm .............. 730x350x300Weight .......................................... 40 kg
* With cooling tank unit 0,2-0,7 l/min.
Part No.
Intended for grinding all kinds of button bit.It is capable of handling threaded and cone-typebutton bits upp to Ø 127 mm and DTH button bits up to Ø 250 mm (max. shank Ø 130 mm).
Hydraulic grinder without cooling unit 796-6235
Hydraulic grinder with cooling unit 796-6236
Accessories optionalBit holder insert for retrac-bits compl. 797-5502-50Guard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-clamping device, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete, 10 l 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Priority fl ow divider for fi xed pumps 797-5414-01Grease gun 797-5870-20Grinding cups See page 121
Complete grinding head 797-5130-10
Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10Air tool oil, 1 liter 797-5870-90
8-1_
900
96 • TOP HAMMER DRILLING TOOLS
GrindingButton bit grinder RG420E
RG420E
Technical data
Air pressure ................................. Max. 13 bar/ Min. 4 barAir consumption ........................... 2-3 l/secWater pressure ............................ Max. 8 bar/Min. 4 barWater consumption ...................... 2-4 l/min *Rated power (motor) ..................... 1.5 kWCoolant/fl ushing medium ............. WaterAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm .............. 730x350x300Weight .......................................... 43 kg
* With cooling tank unit 0,2-0,3 l/min.
Part No.
Intended for grinding all kinds of button bit.It is capable of handling threaded and cone-typebutton bits upp to Ø 127 mm and DTH button bits up to Ø 250 mm (max. shank Ø 130 mm).
Electric powered grinder without cooling unit 796-6215-XX Electric powered grinder with cooling unit 796-6216-XX
Electric powered grinder
220-240 V 1 phase 50 Hz 796-62XX-50260 V 3 phases 50 Hz 796-62XX-51380-420 V 3 phases 50 Hz 796-62XX-52440 V 3 phases 50 Hz 796-62XX-55550 V 3 phases 50 Hz 796-62XX-56660 V 3 phases 50 Hz 796-62XX-57500 V 3 phases 50 Hz 796-62XX-58220-240 V 3 phases 50 Hz 796-62XX-59
220-290 V 3 phases 60 Hz 796-62XX-60380-480 V 3 phases 60 Hz 796-62XX-61 550 V 3 phases 60 Hz 796-62XX-65600 V 3 phases 60Hz 796-62XX-66
Accessories optionalBit holder insert for retrac-bits compl. 797-5502-50Guard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-clamping device, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete, 10 l 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28 Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109
Complete grinding head 797-5130-10
Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10
8-1_
900
TOP HAMMER DRILLING TOOLS • 97
GrindingButton bit grinder RG420P/H/E Manual
RG420P/H/E Manual
Part No.
Intended for grinding all kinds of button bit.It is capable of handling threaded and cone-typebutton bits upp to Ø 127 mm and DTH button bits up to Ø 250 mm (max. shank Ø 130 mm).
Air powered grinder without cooling unit 796-6300
Air powered grinder with cooling unit 796-6301
Hydraulic powered grinder without cooling unit 796-6330
Hydraulic powered grinder with cooling unit 796-6331
Electric powered grinder without cooling unit 796-6310-XX
Electric powered grinder with cooling unit 796-6311-XX
Electric powered grinder220-240 V 1 phase 50 Hz 796-63XX-50260 V 3 phases 50 Hz 796-63XX-51380-420 V 3 phases 50 Hz 796-63XX-52440 V 3 phases 50 Hz 796-63XX-55550 V 3 phases 50 Hz 796-63XX-56660 V 3 phases 50 Hz 796-63XX-57500 V 3 phases 50 Hz 796-63XX-58220-240 V 3 phases 50 Hz 796-63XX-59
220-290 V 3 phases 60 Hz 796-63XX-60380-480 V 3 phases 60 Hz 796-63XX-61 550 V 3 phases 60 Hz 796-63XX-65600 V 3 phases 60Hz 796-63XX-66
Accessories optionalGuard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-clamping device, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28 Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109
Complete grinding head 797-5130-10
Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10Air tool oil, 1 liter 797-5870-90
8-1_105
Technical data Manual P Manual H
Manual E
Air pressure ................... Max. 13 bar Max. 13 bar Max. 13 bar Min. 6.5 bar Min. 4 bar
Min. 4 barAir consumption ............. 40-60 l/sec 2-3 l/sec 2-3 l/secHydraulic pressure ......... Max. 200 bar Min. 140 barOil consumption .............. 12 l/minWater pressure .............. Max. 8 bar Max. 8 bar Max. 8 bar Min. 4 bar Min. 4 bar
Min. 4 barWater consumption ........ 2-4 l/min * 2-4 l/min * 2-4 l/min *Rated power (motor) ....... 1.7 kW 3 kW 1.5 kWAir connection, hose ....... 3/4" 3/8" 3/8"Water connection, hose .. 3/8" 3/8" 3/8"Dimensions: HxWxD mm 730x350x300 730x350x300 730x350x300
Weight ............................... 41 kg 38 kg 41 kg
* With cooling tank unit 0,2-0,3 l/min.
98 • TOP HAMMER DRILLING TOOLS
GrindingButton bit grinder RG440
RG440
Technical data
Air pressure ................................. Max. 13 bar/ Min. 6.5 barAir consumption ........................... 5-6 l/secRated power (motor) ..................... 1.5 kWWater pressure ............................. Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Coolant/fl ushing medium ............. WaterAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm ............. 990x670x795Weight .......................................... 95 kg
* With cooling tank unit 0,2-0,3 l/min.
Part No.
Intended for grinding all kinds of button bit.It is capable of handling threaded and cone-typebutton bits upp to Ø 152 mm.
Grinder without cooling unit 796-6005-XX
Grinder with cooling unit 796-6006-XX
Electric powered grinder220-240 V 1 phase 50 Hz 796-6005-50260 V 3 phases 50 Hz 796-6005-51380-420 V 3 phases 50 Hz 796-6005-52440 V 3 phases 50 Hz 796-6005-55550 V 3 phases 50 Hz 796-6005-56660 V 3 phases 50 Hz 796-6005-57500 V 3 phases 50 Hz 796-6005-58220-240 V 3 phases 50 Hz 796-6005-59
220-290 V 3 phases 60 Hz 796-6005-60380-480 V 3 phases 60 Hz 796-6005-61 550 V 3 phases 60 Hz 796-6005-65600 V 3 phases 60Hz 796-6005-66
Accessories optionalBit mandrels. See manual. 797-5348-XX*Cooling/Flushing tank unit, complete, 10 l 797-5488-75Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109
Complete grinding head 797-5130-10
Recommen ded lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10
* Bit mandrel for T38 bits, 797-5348-38 is included in delivery.
8-1_
97d
TOP HAMMER DRILLING TOOLS • 99
8-1_
97e
GrindingButton bit grinder RG460
RG460
Technical data
Air pressure ................................. Max. 13 bar/ Min. 6.5 barAir consumption ........................... 5-6 l/secRated power (motor) ..................... 1.5 kWWater pressure ............................. Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Coolant/fl ushing medium ............. WaterAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm ............. 990x670x795Weight .......................................... 95 kg
* With cooling tank unit 0,2-0,3 l/min.
Part No.
Intended for grinding DTH bits up to Ø 280 mm.(max shank diameter 110 mm)
Grinder without cooling unit 796-6105-XX
Grinder with cooling unit 796-6106-XX
Electric powered grinder220-240 V 1 phase 50 Hz 796-6105-50260 V 3 phases 50 Hz 796-6105-51380-420 V 3 phases 50 Hz 796-6105-52440 V 3 phases 50 Hz 796-6105-55550 V 3 phases 50 Hz 796-6105-56660 V 3 phases 50 Hz 796-6105-57500 V 3 phases 50 Hz 796-6105-58220-240 V 3 phases 50 Hz 796-6105-59
220-290 V 3 phases 60 Hz 796-6105-60380-480 V 3 phases 60 Hz 796-6105-61 550 V 3 phases 60 Hz 796-6105-65600 V 3 phases 60Hz 796-6105-66
Accessories optionalComplete bit holder for threaded bits 797-5503-60Cooling/Flushing tank unit, complete, 10 l 797-5488-75Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109
Complete grinding head 797-5130-10
Recommen ded lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10
100 • TOP HAMMER DRILLING TOOLS
GrindingBit blaster RG500
RG500
Part No.
Fully automatic bit blaster for removing of excessive
steel from the bit face on all types of bits
from 33 mm to 195 mm in diameter.
Bit Blaster 796-9200-XX
Electric power 220-240 V 1 phase 50 Hz 796-9200-50260 V 3 phases 50 Hz 796-9200-51380-420 V 3 phases 50 Hz 796-9200-52440 V 3 phases 50 Hz 796-9200-55550 V 3 phases 50 Hz 796-9200-56660 V 3 phases 50 Hz 796-9200-57500 V 3 phases 50 Hz 796-9200-58220-240 V 3 phases 50 Hz 796-9200-59
220-290 V 3 phases 60 Hz 796-9200-60380-415 V 3 phases 60 Hz 796-9200-61 550 V 3 phases 60 Hz 796-9200-65600 V 3 phases 60Hz 796-9200-66
Accessories optionalBit holders for threaded bits 797-5615-xx*Cyclone fi lter unit 796-9250-xx
*Note! No bit mandrels are included
8-1_113
Technical data
Air pressure ................................. 5-7 barAir consumption ........................... 5 bar 6 bar 7 bar 8 mm nozzle ................................. 47 l/s 57 l/s 63 l/s
9,5 mm nozzle ............................... 67 l/s 80 l/s 93 l/sRated power (motor) ..................... 0,3 kWBlast tank volume ......................... 30 l /100 kg Dimensions: HxWxD mm ............. 1650(1700)x800x1010 Weight .......................................... 350 kg
Technical data for cyclone fi lter unit
Air pressure ................................. 5-7 bar
Air consumption ........................... 5-6 l/sRated power (motor) ..................... 0,4 kWDimensions: HxWxD mm ............. 1700x500x750 Weight .......................................... 60 kg
TOP HAMMER DRILLING TOOLS • 101
GrindingCross bit grinder RG300
RG300
RG300 is intended for frontal grinding of cross bits up to Ø 64 mm.
Grinder RG300, with pneumatic 796-3201-XX 1)
bit holder.
1) The last two digits (XX) in the ordering code are used to specify the electrical equipment, see table.
260 V 3 phases 50 Hz 796-32XX-51380/420 V 3 phases 50 Hz 796-32XX-52440 V 3 phases 50 Hz 796-32XX-55550 V 3 phases 50 Hz 796-32XX-56660 V 3 phases 50 Hz 796-32XX-57500 V 3 phases 50 Hz 796-32XX-58220-240 V 3 phases 50 Hz 796-32XX-59
220-290 V 3 phases 60 Hz 796-32XX-60380-415 V 3 phases 60 Hz 796-32XX-61550 V 3 phases 60 Hz 796-32XX-65600 V 3 phases 60 Hz 796-32XX-66
Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, cross bits 126° 797-6035-06
Accessories optionalManual gauge-grinding unit 796-6050-50Semi-automatic gauge-grinding unit, (standard Cross D) 796-2960-XXTimer for gauge-grinder, 60 sec. 797-6015-56Pneumatic bit-holder without mandrel 797-6020Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Dressing template, straight (Cross D) 797-6035-45Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112
Recommended lubricantsAir tool oil, 1 litre 797-5870-90Grease, 0.4 kg cartridge 797-5773-20
8-1_112
Part No.
Technical data
Rated power .......................... 1.7 KWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m. Water pressure ...................... Max. 8 bar, Min. 4 bar
Dimensions: (HxWxD mm) ..... 1250x1120x1350 Weight .................................... 190 kg
Grinding units:Rated power .......................... 0,37 kW Stroke frequency 50Hz .......... 140 strokes/min Stroke frequency 60Hz .......... 168 strokes/min
NOTE! Grinding wheels and
mandrels are not included.
102 • TOP HAMMER DRILLING TOOLS
GrindingCross bit grinder RG320
RG320
RG320 is intended for frontal andgauge grinding of cross bits up to Ø 64 mm.
RG320 with right mounted 796-3231-XX 1)
frontal and left mounted semi-automaticgauge grinding equipment with pneumatic bit holders
1) The last two digits (XX) in the ordering code are used to specify the electrical equipment, see table.
260 V 3 phases 50 Hz 796-32XX-51380/420 V 3 phases 50 Hz 796-32XX-52440 V 3 phases 50 Hz 796-32XX-55550 V 3 phases 50 Hz 796-32XX-56660 V 3 phases 50 Hz 796-32XX-57500 V 3 phases 50 Hz 796-32XX-58220-240 V 3 phases 50 Hz 796-32XX-59
220-290 V 3 phases 60 Hz 796-32XX-60380-415 V 3 phases 60 Hz 796-32XX-61550 V 3 phases 60 Hz 796-32XX-65600 V 3 phases 60 Hz 796-32XX-66
Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, cross bits 126° 797-6035-06Dressing template, straight 797-6035-45
Accessories optionalTimer for gauge-grinder, 60 sec. 797-6015-56Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112
Recommended lubricantsAir tool oil, 1 litre 797-5870-90Grease, 0.4 kg cartridge 797-5773-20
8-1_114
Part No.
Technical data
Rated power .......................... 1.7 KWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m.Water pressure ...................... Max. 8 bar, Min. 4 bar
Dimensions: (HxWxD mm) 1250x1350x1350Weight .................................... 245 kg
Grinding units:Rated power .......................... 0,37 kWStroke frequency 50Hz .......... 140 strokes/minStroke frequency 60Hz .......... 168 strokes/min
Semiautomatic gauge grinding unit (796-2960-XX):Rated power .......................... 0,45 kWStroke frequency 50Hz .......... 93 strokes/minStroke frequency 60Hz .......... 112 strokes/minSpeed 50Hz............................ 120 r.p.m.Speed 60Hz ........................... 144 r.p.m. Weight .................................... 75 kg
NOTE! Grinding wheels and
mandrels are not included.
TOP HAMMER DRILLING TOOLS • 103
GrindingCross bit grinder RG340
RG340
RG340 is a frontal grinding machine. Intended for frontal grinding of cross bits up to Ø 64 mm.
RG340, with pneumatic 796-3301-XX 1)
bit holder
1) The last two digits (XX) in the ordering code are used to specify the electrical equipment, see table.
260 V 3 phases 50 Hz 796-330X-51380/420 V 3 phases 50 Hz 796-330X-52440 V 3 phases 50 Hz 796-330X-55550 V 3 phases 50 Hz 796-330X-56660 V 3 phases 50 Hz 796-330X-57500 V 3 phases 50 Hz 796-330X-58220-240 V 3 phases 50 Hz 796-330X-59
220-290 V 3 phases 60 Hz 796-330X-60380-415 V 3 phases 60 Hz 796-330X-61 550 V 3 phases 60 Hz 796-330X-65600 V 3 phases 60 Hz 796-330X-66
Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, cross bits 126° 797-6035-06
Accessories optionalPneumatic bit-holder without mandrel 797-6020Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112
Recommended lubricantsAir tool oil, 1 litre 797-5870-90Grease, 0.4 kg cartridge 797-5773-20
8-1_100b
Technical data
Rated power .......................... 1.7 KWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m.Water pressure ...................... Max. 8 bar/ Min. 4 barDimensions: (HxWxD mm) ..... 1250x1350x1350Weight .................................... 210 kg
Grinding units:Rated power .......................... 2 x 0,37 kWStroke frequency 50Hz .......... 140 strokes/minStroke frequency 60Hz .......... 168 strokes/min
NOTE! Grinding wheels and
mandrels are not included.
Part No.
104 • TOP HAMMER DRILLING TOOLS
GrindingCross bit grinder RG360
RG360
RG360 is a frontal grinding machine. Intended for frontal grinding of X-bits up to Ø 76 mm.
RG360 with pneumatic bit holder 796-3601-XX 1)
1) The last two digits (XX) in the ordering code are used to specify the electrical equipment, see table.
260 V 3 phases 50 Hz 796-360X-51380/420 V 3 phases 50 Hz 796-360X-52440 V 3 phases 50 Hz 796-360X-55550 V 3 phases 50 Hz 796-360X-56660 V 3 phases 50 Hz 796-360X-57500 V 3 phases 50 Hz 796-360X-58220-240 V 3 phases 50 Hz 796-360X-59
220-290 V 3 phases 60 Hz 796-360X-60380-415 V 3 phases 60 Hz 796-360X-61550 V 3 phases 60 Hz 796-360X-65600 V 3 phases 60 Hz 796-360X-66
Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, X-bits 75° 797-6035-07Dressing template, X-bits 105° 797-6035-08
Accessories optionalPneumatic bit-holder without mandrel 797-6020Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112
Recommended lubricantsAir tool oil, 1 litre 797-5870-90Grease, 0.4 kg cartridge 797-5773-20
Part No.
Technical data
Rated power .......................... 1.7 kWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m.Water pressure ...................... max. 8 bar/ Min. 4 barDimensions (HxWxD mm) ...... 1250x1350x1350Weight .................................... 245 kg
Grinding units:Rated power .......................... 2 x 0,37 kWStroke frequency 50Hz .......... 140 strokes/minStroke frequency 60Hz ................168 strokes/min
NOTE! Grinding wheels and
mandrels are not included.
8-1_100b
TOP HAMMER DRILLING TOOLS • 105
GrindingIntegral steel grinder RG100P
RG100P
Mobile, lightweight, pneumatic grinder.Intended for frontal and gauge grinding of chisel integral steels.
Complete grinder, air powered 796-5300
Accessories included in deliveryGrinding wheel for dry grinding 797-1227-15Protective goggles 797-5771T - hexagon wrench 797-5766-06
Accessories optionalGrinding wheels:For dry grinding 797-1227-15For wet grinding 797-1227-10In line oiler 797-5747-50Kit for grinding plug-hole drill steel steels 797-5489-50Mounting bracket (for drill rig) 797-5330-91Support for integral steels 797-5330-92Grinding template for chisel bit 795-1343Grinding template for plug-hole steels 795-1336
Recommended lubricantsAir tool oil, 1 litre 797-5870-90Grease, 0,4 kg cartridge 797-5773-20
8-1_73
W
dD
D 1
8-1_80
w
Part No.
Technical data
Air pressure ........................... Max 8 bar/ Min. 6 barAir consumption .................... 40-60 l/secRated power (motor) .............. 1.7 kWIdling speed ........................... 4900 r.p.m.Hose connections:Air, air hose ............................ 12.5 mm (1/2") IDAir or water hose for cooling . 9.5 mm (3/8") IDDimensions: HxWxD mm ....... 660x550x350Grinding wheel dimesions ..... 127x63x32 mm Weight inclusive of grinding wheel 16.5 kg
Cutting-edge radius .............. 80 mmCutting-edge angle ................ 110°
D = 127 mmW =
63 mmd = 32 mmD1 =
Grinding wheel
106 • TOP HAMMER DRILLING TOOLS
GrindingIntegral steel grinder RG100H
RG100H
Mobile, lightweight, hydraulic grinder.Intended for frontal and gauge grinding of chisel
integral steel.
Complete grinder, hydraulic powered 796-5330
Accessories included in deliveryGrinding wheel for dry grinding 797-1227-15Protective goggles 797-5771T - hexagon wrench 797-5766-06
Accessories optionalGrinding wheels:For dry grinding 797-1227-15For wet grinding 797-1227-10Kit for grinding plug hole drill steels 797-5489-50Mounting bracket (for drill rig) 797-5330-91Support for integral steels 797-5330-92Grinding template for chisel bit 795-1343Grinding template for plug hole steels 795-1336
Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20
W
dD
D 1
8-1_80
w
D = 127 mmW = 63 mmd = 32 mmD1 = 80 mmw = 50 mm
Part No.
Technical data
Hydraulic pressure ................ Max 200 bar/ Min. 140 barOil fl ow consumption ............. 12 l/minAir pressure ........................... Max 8 barAir consumption .................... 5-10 l/secRated power (motor) .............. 4 kWIdling speed ........................... 3700 r.p.m.Hose connections:Hydraulic, hydraulic hose ...... R 3/8" female threadAir, air hose ............................ 9.5 mm (3/8") IDWater, water hose ................. 9.5 mm (3/8") IDDimensions: HxWxD mm ....... 600x550x350Grinding wheel dimensions ... 127x63x32 mm
Cutting-edge radius .............. 80 mmCutting-edge angle ................ 110°
8-1_73C
Grinding wheel
TOP HAMMER DRILLING TOOLS • 107
GrindingIntegral steel grinder RG120E
RG120E
W
dD
D 1
8-1_80
w
8-1_61
Part No.
D = 152 mmW =
83 mmd = 63.5 mmD1 =
Electric grinder intended for frontal and gauge grinding of chisel integral steels.
Complete grinder (without water tray) 796-5012-XX1)
1) The last two digits (XX) in the ordering code are used to specify the electrical equipment, see table.
220-240 V 1 phase 50 Hz 796-5012-50260 V 3 phases 50 Hz 796-5012-51380/420 V 3 phases 50 Hz 796-5012-52440 V 3 phases 50 Hz 796-5012-55550 V 3 phases 50 Hz 796-5012-56660 V 3 phases 50 Hz 796-5012-57500 V 3 phases 50 Hz 796-5012-58220-240 V 3 phases 50 Hz 796-5012-59
220-290 V 3 phases 60 Hz 796-5012-60380-415 V 3 phases 60 Hz 796-5012-61550 V 3 phases 60 Hz 796-5012-65600 V 3 phases 60 Hz 796-5012-66
Accessories included in deliveryGrinding wheel for dry grinding 797-1252-15T - hexagon wrench 6 mm 797-5766-06Protective goggles 797-5771
Accessories optionalGrinding wheels:For dry grinding 797-1252-15For wet grinding 797-1252-10Water tray (plastic) 797-5346Support legs (set 2 pcs) 797-5347Grinding template for chisel bit 795-1343
Technical data
Air pressure ................................ Max 8 bar/ Min. 6 barAir consumption ......................... 20-45 l/secIdling speed ................................ 4200 r.p.m.Air motor ..................................... 1.5 kWHose connections:Air, air hose ................................. 12.5 mm (1/2") IDWater, water hose ...................... 9.5 mm (3/8") IDWeight inclusive of grinding wheel 38 kg
Cutting-edge radius ................... 80 mmCutting-edge angle ..................... 110°
Grinding wheel
108 • TOP HAMMER DRILLING TOOLS
GrindingIntegral steel grinder RG140P/H
8-1_104
RG140P/H
RG140P and 140H are intended for frontal and gauge grinding of integral steels vith 3 or 4 inserts and threaded or tapered bits.
Grinder RG140P, pneumatic powered 796-3800
Grinder RG140H, hydraulic powered 796-3830
Accessories included in deliveryGrinding wheel dresser 796-1858T - hexagon wrench 797-5766-06
Protective goggles 797-5771Pressing template for crossbit 797-6035-08
Accessories optionalGrinding wheel, dry, 132° 797-1185-28Grinding wheel, dry, straight for gauge grinding 797-1101-25Dressing template 4-inserts (cross bit) 797-6035-08Dressing template 3-inserts 797-6035-23Grinding template, cross bit 795-1343Spare rollers for wheel dresser 796-1867Mounting bracket (for drill rig) 797-5330-91
For Sandvik DC120 (Commando 120):Hydraulic mounting kit 797-5775-20
Recommended lubricantsAir tool oil (IXP), 1 litre 797-5870-90Grease (IXH), 0,4 kg cartridge 797-5773-20
Technical data Sanroc IXP Sanroc IXH
Hydraulic pressure ....................... – Max.200 bar
Min. 140 barOil fl ow consumption .................... – 12 l/minAir pressure .................................. Max 8 bar – Min. 6 barAir consumption ........................... 40-60 l/sec –Rated power ................................. 1.7 KW 4.0 KWIdling speed .................................. 3000 r.p.m. 3000 r.p.m.Dimensions: Grinder (HxWxD mm) .................... 250x285x395 250x240x395Grinding wheel 132°, DxWxd mm . 200x28x32 200x28x32Grinding wheel straight, DxWxd mm200x32x32 200x32x32Weight ........................................... 20 kg 18 kg
Air hose ......................................... 12.5 mm (1/2") ID –
Hydraulic hose .............................. – R 3/8"
NOTE! Grinding wheels and
mandrels are not included.
Part No.
TOP HAMMER DRILLING TOOLS • 109
GrindingGrinding cups
Grinding cups for RG410-RG460 grinders
7 mm 797-5400-078 mm 797-5400-089 mm 797-5400-0910 mm 797-5400-1011 mm 797-5400-1112 mm 797-5400-1213 mm 797-5400-1314 mm 797-5400-1416 mm 797-5400-1618 mm 797-5400-18
7 mm 797-5295-078 mm 797-5295-089 mm 797-5295-0910 mm 797-5295-1011 mm 797-5295-1112 mm 797-5295-1213 mm 797-5295-1314 mm 797-5295-1416 mm 797-5295-1618 mm 797-5295-18
8-1_57
8-1_56
For button size Part No.
Sancup Super, (white)For redressing super-spherical buttons
Sancup Super, (red)For redressing R-ballistic buttons
Shank Ø 9 mm.
Shank Ø 9 mm.
Grinding cups for AC: LSD, CME: VS 200/ 220GTA, Jasco and others
7-8-9 mm 797-5356-0810 mm 797-5356-10
11 mm 797-5356-1112-13 mm 797-5356-1214 mm 797-5356-1416 mm 797-5356-16
8-9 mm 797-5366-0910 mm 797-5366-10
11 mm 797-5366-1112-13 mm 797-5366-1214 mm 797-5366-1416 mm 797-5366-16
Sancup (black)For redressing spherical buttons
Shank Ø 8 mm.* For older grinder remove O-ring before use (VS 200)
Sancup (black)For redressing ballistic buttons
Shank Ø 8 mm.* For older grinder remove O-ring before use (VS 200)
110 • TOP HAMMER DRILLING TOOLS
GrindingGrinding wheels
Grinding wheel for RG140P, RG140H (132°)
200 28 32 797-1185-28200 32 32 797-1101-32200 25 32 797-1101-25
dD
8-1_81
W
D W d Part No.
For cross bits 33-43 mm DryStraight wheel for gauge grinding
Dry
Grinding wheel, wet grinding
90° Cross bits 33-35 132° 300 23 32 797-1190-23 90° 38-41 132° 300 26 32 797-1190-2690° 43-45 132° 300 29 32 797-1190-2990° 48-51 132° 300 32 32 797-1190-32
75° X-bits 64 126° 300 35 32 797-1175-3575° 76 126° 300 44 32 797-1175-44105° 64 139° 300 48 32 797-1105-48105° 76 139° 300 58 32 797-1105-58D d
W
8-1_23
Bit insert Wheelangle mm angle D W d Part No.
Straight wheel for gauge grinding 35-76 300 32 32 797-1100-32
TOP HAMMER DRILLING TOOLS • 111
GrindingGrinding wheels
W
d
DD 1
8-1_24
w
Grinding wheel for RG100P, RG100H and RG120P, RG120E
125 63 32 80 50 797-1227-15125 63 32 80 50 797-1227-10
150 83 63.5 100 64 797-1252-15150 83 63.5 100 64 797-1252-10
D W d D1 w Part No.
For RG100For RG100
For RG120For RG120
Secoroc: Junior and Senior, AC: Teroc 1500/1501
200 102 32 150 80 797-1250-10Wet
D W d D1 w Part No.
W
d
DD 1
8-1_24
w
112 • TOP HAMMER DRILLING TOOLS
GrindingGrinding accessories
Part No.
Mandrel, complete for pneumatic bit holder, also for semi-automatic gauge-grinding unit
8-1_103
For R23 (29/32") thread 797-6020-23For R25 (1") thread 797-6020-25For R28 (1 1/8") thread 797-6020-28For R32 (1 1/4") thread 797-6020-32
For α330 thread 797-6020-33For R35 (1 3/8") thread 797-6020-35For R38/T38 (1 1/2") thread 797-6020-38For T45 (1 3/4") thread 797-6020-45Wheel dresser, complete 796-1858
Wheel dresser
8-1_37
- Shaft (1 pcs) 1) 796-1862- Bearing bushing (2 pcs) 1) 796-1863- Screw (6 pcs) 1) 796-1865- Cover (2 pcs) 1) 796-1866- 1 set of dresser rollers 1) 796-1867
1) Included in a complete unit.
For plug hole drill steels type 721-XXXX and 722-XXXX
795-1336
For buttons up to 16 mm
795-1396
For OD-bits
795-1340
795-1343
2 mm3 mmRadius 80 mm
Max height of antitaper
Carbideinsert
Whe
el
Whe
el
Whe
el
Inte
gral
sBi
ts0
0
10
10110
20304050607080
8-1_89
For integrals with cross bit / For cross and X-bits with diameter up to 115 mm / For integrals with chisel bit and motor drill steels
Pneumatic bit-holder, complete without mandrel for Sandvik RG300/320/340/360 grinders
8-1 99
797-6020
Auxiliary tools
Auxiliary tools
Page
Bit adapters ................................................................................. 115
Reduction couplings ................................................................... 115
Wrenches and knock-off-tools .................................................. 116
Fishing tools, thread grease and gauges .................................... 117
Drill steel straightener................................................................118
TOP HAMMER DRILLING TOOLS • 115
Auxiliary toolsBit adapters
LDF M
2-1_
158b
R23 R32 200 - 7 7/8” 35 1 3/8” 7837-3301
R25 R32 173 - 6 13/16” 45 1 3/4” 7832-3301
R28 R32 230 - 9 1/16” 40 1 37/64” 7839-3301
R32 T38 225 - 8 55/64” 45 1 49/64” 7833-4401R32 R38 225 - 8 55/64” 45 1 49/64” 7833-4301
T35 T38 250 - 9 27/32” 48 1 7/8” 7337-4401
R38 R32 270 - 10 41/64” 55 2 5/32” 7834-3303R38 T38 245 - 9 21/32” 55 2 5/32” 7834-4401
T38 R32 270 - 10 41/64” 57 2 1/4" 7334-3301T38 T45 285 - 11 7/32" 57 2 1/4" 7334-5401T38 R38 280 - 11 1/32” 57 2 1/4” 7334-4301
T45 T38 265 - 10 7/16" 63 2 31/64" 7335-4401T45 T51 285 - 11 7/32" 63 2 31/64" 7335-6401
T51 T45 285 - 11 7/32" 71 2 51/64" 7336-5401
Wrench fl at
mm
28.5
38
38
3838
38
44.544.5
44.544.544.5
3844.5
44.5
Reduction couplings
L
D
F2
2-1_
293b
F1
R32 R28 165 - 6 1/2” 44 1 47/64” 7993-0444R32 R25 160 - 6 1/4” 43 1 11/16” 7993-2443
R38 R32 170 - 6 3/4” 55 2 5/32” 7994-3455
T38 R32 195 - 7 11/16” 55 2 5/32” 7314-3555T38 R38 185 - 7 9/32” 55 2 5/32” 7314-4455T38 T45 220 - 8 43/64” 61 2 13/32” 7314-6261
T51 T45 218 - 8 19/32” 71 2 51/64” 7316-6271
Threads Dimensions Part No. L DF M mm ft in mm in
Threads Dimensions Part No. L DF1 F2 mm ft in mm in
116 • TOP HAMMER DRILLING TOOLS
Auxiliary toolsWrenches and knock-off-tools
Knock-off-tools for Hex 22 and Hex 25 pilot rods, type 7922-XXXX-XX
2-1_
114
795-1469
For integral drill steels and shank rods
600 1' 11 5/8" 19 3/4" 795-1407600 1' 11 5/8" 22 7/8" 795-1408600 1' 11 5/8" 28 1 1/8" 795-2423
8-1_1
5
D L
Dimensions Part No.L Dmm ft in mm in
Hex 19Hex 22Hex 28
For extension rods
300 – 11 13/16" 25 1" 795-1431300 – 11 13/16" 28 1 1/8" 795-1492370 1' 2 9/16" 32 1 1/4" 795-1432370 1' 2 9/16" 38 1 1/2" 795-1494
380 1' 2 31/32” 65 2 7/12” 795-1495
620 2' 13/32" 35 1 25/64" 795-2476850 2' 9 15/32" 45 1 3/4" 795-1420
D
4-1_
33
L
D
4-1_
34
L
Hex 25, Round 32Hex 28
Hex 32, Round 39Round 46
DTH
Hex 35Round 52
Knock-off-tools for tapered bits
2-1_
485
795-1467 795-1468
Hex 22Hex 25
Pneumatic knock-off-tool for tapered bits
Complete unit 796-1400
Chisel (wear part) 797-5712-01Guide sleeve 797-5114-03
Technical data
Air pressure ............................... 6-8 barAir consumption ........................ 7-9 l/sAir hose ..................................... 12.5 mm (1/2") IDDimensions: (HxWxD mm) ......... 500x300x120Weight ....................................... 18 kg
8-1_111
TOP HAMMER DRILLING TOOLS • 117
Auxiliary toolsFishing tools, thread grease and gauges
Fishing sleeve
33 – 185 R22 795-1629 35 – 225 R22 795-1630 39 – 215 R25 795-1631 38 – 275 R25 795-1632 48 42.5 335 R28 795-1687 48 46 300 R32 795-1604 60 – 353 R38 795-1605 52 50 284 T35 795-1613 60 57.2 353 T38 795-1607 71 68 393 T45 795-1608 80 75.5 440 T51 795-1609 92 87.5 450 GT60 795-2601 89 84.5 450 GT60 795-2603102 92 410 ST68 795-1696
Dimensions Part No. D D1 L Thread
For catchingR22 Hex. rods
R22 coupling sleevesR25 Hex. rods
R25 coupling sleevesR28 Hex. rods/coupling sleeves
R32 round/Hex. rods/coupling sleevesR38 round rods/coupling sleevesT35 round rods/coupling sleeves
T38 round rods/coupling sleeves/MF-rodsT45 round rods/coupling sleeves/MF-rodsT51 round rods/coupling sleeves/MF-rods
GT60 rodsGT60 rods
ST68 tubes Ø87
Thread grease
8-1_19
215 – 170 – 795-1960300 – 380 – 795-196153/57 – 235 – 795-1962300 – 380 – 795-1963370 – 690 – 795-1967610 – 870 – 795-1964
Can 4.5 kgCan 18.0 kg
Tube 0.40 kgLow temperature grease, can 18.0 kg
Barrel 50 kgBarrel 240 kg
Fishing pike
10 4 160 R22 795-1600 12 4 200 R25 795-1601 14.8 4 220 R28 795-1686 19.4 4 280 R32 795-1606 18 8 237 R38 795-1611 19.4 8 237 T38 795-1676 25 8 275 T45 795-1681 27 15 285 T51 795-1690 57 24 500 ST58 795-1699 71 32 541 ST68 795-2600
For catchingR22 rods 1)
R25 rods 1)
R28 rods 1)
R32 rods 1)
R38 rods 2)
T38 rods 2)
T45 rods 2)
T51 rods 2)
ST58 tubes Ø76 2)
ST68 tubes Ø87 2)
1) Without fl ushing hole.2) With fl ushing hole.
D D18-1_18
L
D
8-1_
17
L
Gauges / Wear gauge for male and female threads
8-1_7 795-1336
Gauges / Chuck wear gauge
8-1_44
795-1343
118 • TOP HAMMER DRILLING TOOLS
Drill steel straightener for Hex19 to Round 52
8-1_ 90
796-2930
796-2930-52 796-2931
Manual/Hydraulic
Electric/Hydraulic, 380V/50Hz
Support leg, 1 piece
Part No.
Auxiliary toolsDrill steel straightener
TOP HAMMER DRILLING TOOLS • 119
Code information
Third fi gure group
Integral steels with reduced width of bit (small gauge steel) ................................................................................................... xxx-xxxx-50Integral steels with reduced width of bit, + tolerance (small gauge steel) ................................................................................ xxx-xxxx-5005Integral steels, Premium plus, H22, insert height 19 mm ....................................................................................................... xxx-xxxx-65
Shank rod, drilled for fl ushing tube 4.5-5 mm, packing .......................................................................................................... xxxx-xxxx-13Shank rod, drilled for fl ushing tube < 7 mm, no packing ......................................................................................................... xxxx-xxxx-11
Tapered rod, drilled for fl ushing tube < 7 mm, carburized ...................................................................................................... xxxx-6xxx-11Tapered rod, drilled for fl ushing tube < 7 mm, HF- hardened ................................................................................................. xxxx-11xx-11
Cross bit, cemented carbide grade 42 .................................................................................................................................. xxxx-xxxx-42
Tapered button bits, cemented carbide grade XT48 with ballistic buttons ............................................................................... xxxx-xxxx-B48
Small hole drilling tools
Bench drilling tools Third fi gure group
Insert bits, cemented carbide grade 11 .................................................................................................................................. xxxx-xxxx-11 Insert bits, cemented carbide grade 42 .................................................................................................................................. xxxx-xxxx-42
Button bits, cemented carbide grade MP 45, with spherical buttons ....................................................................................... xxxx-xxxx-S45Button bits, cemented carbide grade MP 45, with ballistic buttons .......................................................................................... xxxx-xxxx-R45Button bits, cemented carbide grade DP 65, with spherical buttons ....................................................................................... xxxx-xxxx-S65Button bits, cemented carbide grade DP 55, with ballistic buttons ......................................................................................... xxxx-xxxx-R55Button bits, cemented carbide grade MP 45, with ballistic buttons ......................................................................................... xxxx-xxxx-R45
Extension rod, Guide tube, carburized ................................................................................................................................... xxxx-xxxx-20Extension rod, HF- hardened ................................................................................................................................................ xxxx-xxxx-30MF-rod, for surface drilling .................................................................................................................................................... xxxx-xxxx-70
Third fi gure group
Cross bits, cemented carbide grade 42 ................................................................................................................................ xxxx-xxxx-42
Button bits, cemented carbide grade XT48 with spherical buttons .......................................................................................... xxxx-xxxx-S48Button bits, cemented carbide grade XT48 with ballistic buttons ............................................................................................. xxxx-xxxx-R48Button bits, cemented carbide grade DP 65 with spherical buttons ......................................................................................... xxxx-xxxx-S65Button bits, one extra hole for side fl ushing ............................................................................................................................ xxxx-xxxxA-xxx
Rods, carburized................................................................................................................................................................... xxxx-xxxx-20
Drifting and tunneling tools
120 • TOP HAMMER DRILLING TOOLS
Bit classifi cation code
H Very hard to hard rock > 2500 bar (250 MPa)M Medium hard rock 1500-2500 bar (150-250 MPa)S Soft rock < 1500 bar (150 MPa)
C Homogeneous (competent) rockF Fissured rock
V Very abrasive rock > 40% silicaA Abrasive rock 20-40% silicaN Non-abrasive rock 0-20% silica
_
_
Tools for long hole drilling underground Third fi gure group
Insert bits, cemented carbide grade 11 .................................................................................................................................. xxxx-xxxx-11 Insert bits, cemented carbide grade 42 .................................................................................................................................. xxxx-xxxx-42
Button bits, cemented carbide grade MP 45, with spherical buttons ....................................................................................... xxxx-xxxx-S45Button bits, cemented carbide grade MP 45, with ballistic buttons .......................................................................................... xxxx-xxxx-B45Button bits, cemented carbide grade DP 65, with spherical buttons ....................................................................................... xxxx-xxxx-S65Button bits, cemented carbide grade DP 65, with semi-ballistic buttons ................................................................................. xxxx-xxxx-R65Button bits, cemented carbide grade MP 45, with semi-ballistic buttons ................................................................................ xxxx-xxxx-R45
Extension rod, carburized ..................................................................................................................................................... xxxx-xxxx-20
Drill tube, carburized ............................................................................................................................................................ xxxx-xxxx-26Drill tube, carburized, with permanent back fl ow valve ........................................................................................................... xxxx-xxxx-46
MF-rod, carburized .............................................................................................................................................................. xxxx-xxxx-20
Code information
TOP HAMMER DRILLING TOOLS • 121
Safety information
Grinding of Cemented Carbide
Grinding or heating a cemented carbide product will produce dust or fumes of hazardous ingredients which can be inhaled, swal-lowed or come in contact with the skin or eyes.
The limiting ingredient in cemented carbide is, from a health and safety point of view, Cobalt. Another hazardous ingredient is Tungsten Carbide.
Cobalt is classifi ed as harmful - may cause sensitization by inhalation or skin contact. Inhalation or skin contact may also cause irritation.
Sensitive persons may experience an allergic reaction. Repeated inhalation of aerosols containing Cobalt may cause obstruction in the respiratory organs. Long term inhalation of increased concentrations may cause permanent disease.
Precautions
- Avoid formation and inhalation of dust.- Wet grinding is recommended instead of dry grinding.- Always use Exhaust Ventilation which is adequate to limit personal exposure well below the Occupational Exposure Limits.- Use Respiratory Protection if ventilation is not available or adequate.- Use Safety Goggles when necessary- Wear suitable Gloves and Protective Clothing.
TOP HAMMER DRILLING TOOLS • 121
Numerical index with weight table
122 • TOP HAMMER DRILLING TOOLS
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
714-0434-65 1,80 20 6714-0635-65 2,40 20 6714-0641-65 2,50 20 6714-0829 3,00 20 6714-0833-65 3,00 20 6714-0834-65 3,00 20 6714-0840-65 3,00 20 6714-1232-65 4,20 20 6714-1234-65 4,20 20 6714-1240-65 4,20 20 6714-1628-50 5,40 20 6714-1631 5,40 20 6714-1633-65 5,40 20 6714-1639-65 5,40 20 6714-1833-65 6,00 20 6714-1839-65 6,00 20 6714-2030 6,60 20 6714-2033-65 6,60 20 6714-2427-50 7,90 20 6714-2432-65 7,90 20 6714-2438-65 7,90 20 6714-3231 10,30 20 6714-3237-65 10,20 20 6714-4030 12,70 20 6714-4036-65 12,70 20 6714-4829 15,20 15 6714-4835-65 15,10 15 6714-5628-50 17,60 15 6714-5634-65 17,60 15 6714-6427-50 20,10 15 6714-6433-65 20,10 15 6714-7226-50 22,50 30 6714-7232-65 22,50 6714-8026-50 24,70 6714-8825-5005 27,00 6714-9625-5005 29,50 30 6
721-1517 0,60 5 10721-1620 0,70 5 10721-1622 0,70 5 10721-1922 0,80 5 10721-2020 0,78 5 10721-2420 0,80 5 10721-2820 0,90 5 10721-3120 1,00 10
724-0424 1,30 20 5724-0429 1,30 20 5724-0627 1,70 20 5724-0823 2,10 20 5724-0828 2,20 5724-0834 2,20 20 5724-1226 3,00 20 5724-1627 3,90 5724-2426 5,65 20 5
728-0424 1,40 20 5728-0429 1,40 20 5728-0828 2,30 20 5
7304-3550-01 5,40 1 787304-3590-03 4,10 1 77-78, 897304-3591-01 4,20 1 77-78, 897304-3593-01 4,70 1 77-787304-3652-01 3,80 2 787304-3655-01 6,35 1 797304-3656-01 4,45 2 78
7304-3825-02 9,90 797304-4200-30 3,00 2 767304-4500-60 2,75 2 767304-4700-01 4,00 2 847304-4700-50 3,30 2 847304-4706-01 4,70 1 847304-4720-01 3,80 2 827304-4723-01 4,10 2 827304-4780-01 6,35 807304-4791-01 6,00 807304-4993-01 5,50 2 797304-7426-01 6,25 807304-7500-60 3,90 2 80-81, 897304-7502-60 5,40 1 76, 827304-7525-19 5,40 817304-7526-80 6,30 1 807304-7531-01 3,90 1 857304-7532-01 5,90 2 867304-7535-02 4,60 1 857304-7536-01 4,30 1 857304-7537-01 5,50 1 867304-7541-02 6,55 867304-7543-60 3,60 2 80-817304-7554-01 5,30 1 857304-7557-01 5,60 1 857304-7576-01 6,90 1 867304-7577-02 8,40 1 867304-7581-60 5,20 807304-7583-40 5,80 897304-7585-01 5,45 1 857304-7586-01 5,90 85
7305-3591-01 5,10 1 77-787305-3593-01 5,80 1 77-787305-3655-01 6,10 1 797305-3690-02 6,90 797305-3826-02 10,25 797305-4791-01 6,25 807305-6008-01 8,90 1 877305-6010-01 9,70 877305-7400-01 9,10 1 867305-7414-01 8,85 807305-7417-01 9,50 807305-7520-01 5,60 1 837305-7525-19 5,50 1 817305-7526-80 6,60 1 807305-7532-01 6,30 1 867305-7537-01 5,80 1 867305-7541-02 6,90 867305-7546-19 7,80 817305-7551-01 7,60 1 867305-7557-01 5,90 1 857305-7576-01 7,20 1 867305-7577-02 8,60 1 867305-7586-01 6,20 85
7306-3655-02 6,80 797306-3690-03 7,20 797306-3692-01 9,50 797306-6008-01 9,30 1 877306-6010-02 10,10 877306-6014-02 11,90 877306-6019-02 13,90 877306-6021-02 11,20 887306-6022-02 13,30 887306-6025-02 15,90 877306-7528-02 8,60 83
Numerical index with weight table
TOP HAMMER DRILLING TOOLS • 123
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
7306-7530-02 16,10 837306-7551-02 8,10 86
7307-3576-01 767307-3593-01 4,50 787307-3652-01 3,70 2 787307-3656-01 4,15 787307-7535-02 4,45 857307-7557-01 5,55 857307-7585-01 5,25 857307-7586-01 5,60 85
7314-3555 2,30 5 1157314-3652 1,50 25, 297314-4455 1,90 5 1157314-6261 2,85 1 115
7316-3671 3,65 1 457316-6271 4,00 1 115
7324-4131-20 25,00 277324-4137-20 29,40 277324-4143-20 33,80 277324-4149-20 39,20 277324-4155-20 44,00 277324-4231-20 27,80 277324-4237-20 33,20 277324-4243-20 38,60 277324-4249-20 44,00 277324-4255-20 48,00 277324-4261-20 57,00 277324-4331C-30 24,10 15 407324-4712C-20 10,60 15 557324-4715C-20 13,30 15 557324-4718C-20 16,10 15 557324-4731-70 25,50 5 397324-4737-70 30,00 397324-4743-70 36,40 397324-6537-20 29,25 15 257324-6543-20 34,00 10 257324-6931-20 18,30 407324-7243-20 35,00 10 297324-7249-20 39,90 10 297324-7255-20 44,80 10 297324-8543-20 33,70 10 297324-8549-20 37,10 10 297324-8555-20 42,00 10 297324-8561-20 46,10 5 297324-8637-20 25,50 5 257324-8643-20 27,50 10 257324-9631-20 24,00 257324-9637-20 27,50 15 257324-9643-20 32,00 10 257324-9649-20 37,00 10 257324-9655-20 42,20 10 257324-9661-20 44,00 5 25
7325-7331C-30 32,90 10 437325-7337C-30 40,00 10 437325-7343C-30 47,00 5 437325-7361C-30 66,50 5 437325-7715C-20 17,60 10 577325-7718C-20 21,00 10 577325-7731-70 35,00 427325-7737-70 41,20 427325-7743-70 47,50 42
7326-5337C-30 50,00 10 457326-5343C-30 56,00 5 457326-5361C-30 85,00 7 457326-5515C-20 23,00 10 597326-5518C-20 27,00 10 597326-5537-70 50,50 10 457326-5543-70 56,50 10 457326-5561-70 87,00 10 45
7327-4718-20 16,10 537327-4731-20 25,40 5 31, 377327-4737-20 32,00 377327-4743-20 35,00 377327-5243-20 35,00 317327-5249-20 40,10 5 317327-5255-20 45,00 5 317327-5261-20 50,00 5 31
7328-6009-02 17,40 1 877328-6020-01 17,30 1 887328-6035-01 22,00 1 88
7329-3716-01 21,70 1 797329-3720-01 26,60 1 797329-6009-02 16,90 1 877329-6020-01 16,80 1 887329-6035-01 22,35 88
7334-3301 2,60 1 1157334-4301 3,35 1 1157334-5401 3,30 1 115
7335-4401 2,90 1 1157335-6401 3,70 1 115
7336-5401 3,80 1 115
7337-4401 1,90 1 115
7378-7615-26 33,20 10 617378-7618-26 41,00 61
7379-8715-26 40,00 10 627379-8715-46 40,00 10 627379-8718-26 47,00 10 62
7514-2664-R55 1,70 5 387514-2664-S45 1,70 5 387514-2670-S45 1,85 5 387514-2676-R55 2,30 5 387514-2676-S45 2,30 5 387514-2689-S45 3,00 3 387514-3864-S45 1,70 5 38, 547514-3864-S65 1,70 5 38, 547514-3876-S45 2,20 5 387514-3876-S65 2,20 5 387514-4064-11 2,05 5 397514-4076A-11 2,60 5 397514-5964-R55 1,65 5 38, 547514-5964-S45 1,65 5 38, 547514-5976-R55 2,30 3 387514-5976-S45 2,30 3 387514-7864-R55 2,00 5 38, 547514-7864-S45 1,95 5 38, 547514-7870-S45 2,40 5 39, 547514-7876-R55 2,90 3 397514-7876-S45 3,00 3 39
Numerical index with weight table
124 • TOP HAMMER DRILLING TOOLS
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
7514-7964-R55 1,85 5 39, 547514-7964-S45 2,00 5 39, 547514-7964-S45 2,00 5 547514-7976-R55 3,20 397514-7976-S45 3,10 3 39
7515-2602-S45 4,00 1 417515-2676-R55 2,50 5 417515-2676-S45 2,35 5 41, 567515-2689-R55 3,10 3 417515-2689-S45 3,00 3 417515-3876-S45 2,30 5 41, 567515-3876-S65 2,30 5 41, 567515-3889-S45 3,40 3 41, 567515-3889-S65 3,60 3 41, 567515-5902-R55 4,00 1 417515-5902-S45 4,00 1 417515-5976-R55 2,40 3 417515-5976-S45 2,45 3 41, 567515-5989-R55 3,20 3 417515-5989-S45 3,20 3 41, 567515-7802-S45 5,90 1 427515-7876-R55 3,20 3 417515-7876-S45 3,25 3 41, 567515-7876-S65 3,05 3 567515-7889-R55 4,30 3 427515-7889-S45 4,40 3 427515-7902-R55 6,00 1 427515-7902-S45 6,20 1 427515-7970-R55 2,85 427515-7976-R55 3,10 3 42, 567515-7976-S45 3,05 3 42, 567515-7989-R55 4,50 3 427515-7989-S45 4,50 3 42, 567515-8270-R45 4,10 3 427515-8270-R45 4,10 3 567515-8276-R45 3,15 3 42, 567515-8289-R45 4,75 3 427516-2602-S45 4,30 1 447516-2615-S45 5,50 1 447516-2627-S45 6,60 1 44
7516-2689-S45 3,60 3 44, 587516-4902-S45 6,10 1 447516-4915-S45 7,85 1 447516-4927-S45 10,20 1 447516-5902-R55 4,35 1 447516-5902-S45 4,45 1 447516-5915-S45 5,60 1 447516-5927-S45 6,00 1 447516-5989-R55 3,20 3 447516-5989-S45 3,60 3 44, 587516-7802-S45 5,80 1 447516-7815-S45 8,10 1 447516-7889-R55 4,15 3 447516-7889-S45 4,15 3 44, 587516-7902-R55 5,75 1 447516-7902-S45 5,75 1 447516-7915-R55 8,35 1 447516-7915-S45 8,15 1 447516-7927-S45 10,50 1 447516-7989-R55 4,35 3 44, 587516-7989-S45 4,25 3 44, 58
7517-7854-R45 1,30 37, 537517-7857-R45 1,50 37, 53
7525-8476-R65 3,40 1 60
7528-5652C-S65 1 617528-8489-R65 4,00 1 61
7529-5652C-S65 14,80 1 627529-6652-S45 8,90 1 627529-6902-S65 5,20 1 627529-7302-R65 5,65 1 627529-7315-R65 7,50 1 627529-8402-R65 5,20 1 627529-8415-R65 5,90 1 62
7600-6014-02 12,95 1 877600-6022-03 14,55 1 887600-6025-02 16,70 1 877600-6030-01 21,00 1 887600-6031-01 20,80 1 877600-7530-02 16,90 1 83
7610-1137-70 73,00 10 477610-1143-70 82,00 10 477610-1161-70 110,00 10 477610-1443-70 85,00 1 47
7620-3802-S45 6,00 1 467620-3815-S45 7,25 1 467620-3827-S55 8,85 1 467620-3892-S45 5,15 1 467620-3896-S45 5,30 1 467620-4792-R55 5,60 1 467620-4902-S45 7,25 1 477620-4915-S45 9,50 1 477620-4927-S55 12,60 1 477620-4940-S55 16,70 1 477620-4952-S55 20,00 1 477620-5902-S45 5,95 1 467620-5915-R55 7,30 1 467620-5915-S45 7,50 1 467620-5927-S55 9,45 1 467620-5940-S55 12,10 1 467620-5952-S55 13,75 1 467620-7902-R55 7,00 1 467620-7902-S45 7,10 1 467620-7915-R55 9,40 1 467620-7915-S45 9,40 1 467620-7927-S55 12,70 1 467620-7940-S55 16,15 4 467620-7996-S45 6,20 5 467620-8118-S55 10,05 5 477620-8702-R45 7,50 1 467620-8792-R45 6,05 1 46
7640-7653-70 111,50 1 477640-8716-70 39,30 1 477640-8743-70 106,00 1 47
7721-4802-S45 2,05 4 26, 307721-4802-S48 2,05 4 287721-4827-S45 3,50 3 26, 307721-4827-S48 3,50 3 287721-4889-S45 1,45 4 26, 307721-4889-S48 1,45 4 287722-4864-S45 0,85 5 7, 20-23, 267722-4876-S45 1,25 5 7, 20-23, 267722-4889-S45 1,70 4 7, 22-23, 26
Numerical index with weight table
TOP HAMMER DRILLING TOOLS • 125
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
7723-4802-S45 3,60 2 52, 557723-4827-S45 5,20 2 55
7732-1045-42 0,65 10 10, 137732-1051-42 0,80 10 137732-1435-42 0,45 10 13, 197732-1438-42 0,55 10 10, 13, 197732-1441-42 0,69 10 10, 13, 197732-5235-S48 0,40 10 13, 197732-5237-S48 0,45 10 197732-5238-R48 0,49 10 137732-5238-S48 0,49 10 13, 197732-5241-S48 0,52 10 13, 197732-5345F-R48 0,77 10 13
7733-1064-42 1,50 10 357733-1345A-42 0,80 10 247733-1451-42 1,05 10 35, 517733-2664-S45 1,65 5 357733-2676-S45 2,00 5 357733-5243-S48 0,70 10 247733-5245-S48 0,75 10 247733-5245-S65 0,75 10 247733-5248-S48 0,92 10 247733-5251-S48 0,97 10 247733-5251-S65 0,97 10 247733-5345-R48 0,77 10 247733-5345-S48 0,78 10 247733-5348-S48 0,95 10 247733-5351-R48 0,95 10 24, 35, 517733-5351-S48 0,96 10 24, 35, 517733-5357C-S48 1,15 10 35, 517733-5443-R48 0,69 10 247733-5445-R48 0,78 10 247733-5448-R48 0,92 10 247733-5451-R48 0,97 10 247733-5602-S45 3,20 1 267733-7851-R55 1,15 5 357733-7851-S45 1,15 10 357733-7851-S45 1,15 10 517733-7864-S45 2,10 5 357733-8251-R45 1,25 5 35, 517733-8257-R45 1,65 5 35, 51
7737-1435-42 0,45 10 127737-1438-42 0,50 10 127737-1633-11 0,40 10 127737-4438A-B48 0,45 10 127737-5235-R48 0,35 10 127737-5241-R48 0,45 10 127737-5345-R48 0,53 10 12
7738-1448-42 1,00 10 297738-5248-S48 0,90 10 297738-5251-S48 0,99 10 297738-5348A-R48 0,96 10 297738-5348A-S48 0,97 10 297738-5348-R48 0,99 10 297738-5348-S48 0,97 10 297738-5351-R48 0,99 10 297738-5351-S48 0,97 10 297738-5602-S45 3,15 1 307738-7854-R48 1,25 5 317738-7854-S48 1,20 5 317739-1438-42 0,55 10 16, 227739-1441-42 0,65 10 16, 22
7739-5238-R48 0,61 10 16, 227739-5238-S48 0,61 10 16, 227739-5241-S48 0,63 10 16, 227739-5243-S48 0,65 10 16
7764-1435-42 0,45 10 217764-1438-42 0,55 10 217764-1441-42 0,65 10 217764-1633-42 0,40 10 217764-4433-S48 0,30 10 217764-4435-S48 0,30 10 217764-5235-R48 0,45 10 157764-5237-S48 0,55 10 217764-5238-R48 0,45 10 157764-5238-S48 0,45 10 217764-5241-S48 0,50 10 21
7765-1438-42 0,55 10 237765-1441-42 0,65 10 237765-5238-R48 0,61 10 237765-5238-S48 0,61 10 237765-5241-S48 0,63 10 237765-5243-S48 0,65 10 23
7766-1345A-42 0,75 10 277766-1448-42 0,95 10 277766-5243-S48 0,65 10 277766-5245-S48 0,75 10 277766-5245-S65 0,75 10 277766-5248-S48 0,82 20 277766-5345A-R48 0,80 20 277766-5345A-S48 0,80 20 277766-5348A-R48 0,85 20 277766-5348A-S48 0,85 20 277766-5351A-R48 0,95 20 277766-5351A-S48 0,95 20 277766-5443-R48 0,65 20 277766-5445-R48 0,75 20 277766-5602-S45 3,15 20 28
7770-5233-B48 0,30 20 87770-5235-B48 0,30 20 87770-9028-42 0,25 20 87770-9030-42 0,30 20 87770-9032-42 0,30 20 87770-9035-42 0,30 20 8
7776-1932-B48 0,20 20 97776-1936-B48 0,20 20 97776-1938-B48 0,24 20 97776-1940-B48 0,30 20 97776-4432-B48 0,21 20 97776-4435-B48 0,25 20 97776-4438-B48 0,30 20 97776-4440-B48 0,30 20 97776-6438-B48 0,30 20 9
7795-5232-B48 0,20 20 87795-5235-B48 0,25 20 87795-5238-B48 0,30 20 87795-6428-B48 0,15 20 87795-6430-B48 0,15 20 8
7801-6103-13 1,10 1 11, 757801-6110-13 3,40 10 11
Numerical index with weight table
126 • TOP HAMMER DRILLING TOOLS
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
7802-6103-13 1,10 1 10, 13, 757802-6108-13 3,00 10 10, 137802-6110-13 3,50 10 10, 137802-7103-14 1,40 1 757802-7503-20 1,60 1 75
7803-3100-30 2,00 2 767803-3576-01 4,75 1 77, 837803-3588-01 3,35 2 76, 837803-3590-03 3,90 1 77, 897803-3591-01 4,10 1 77-78, 83, 897803-3593-01 4,60 1 77-787803-3602-30 2,10 2 847803-3652-01 3,70 2 787803-3656-01 4,10 2 787803-3670-02 4,70 1 787803-4200-30 2,60 2 767803-4700-01 3,70 2 847803-4700-50 2,70 2 847803-4703-01 3,60 2 897803-4725-01 3,30 1 827803-4726-01 2,75 2 827803-7500-61 3,00 2 80-81, 897803-7531-01 3,85 2 857803-7532-01 5,70 1 867803-7535-02 4,20 1 857803-7547-01 2,55 2 847803-7549-01 2,55 2 847803-7553-01 3,90 2 857803-7557-01 5,60 1 857803-7585-01 5,10 1 857803-7586-01 5,40 1 857803-7662-01 5,70 1 847803-7663-01 5,70 1 84
7804-3575-01 4,05 2 767804-3575-01 4,05 2 837804-3590-03 4,20 1 777804-3590-03 4,20 1 787804-3590-03 4,20 1 897804-3590-03 4,20 1 897804-3652-01 3,80 2 787804-3670-02 4,25 0 787804-4700-01 3,90 2 847804-4725-01 3,80 0 827804-4993-01 5,50 1 797804-7500-60 3,50 2 807804-7500-60 3,50 2 817804-7500-60 3,50 2 817804-7500-60 3,50 2 897804-7531-01 4,15 1 857804-7536-01 4,40 1 857804-7554-01 5,20 1 857804-7585-01 5,30 1 85
7805-6015 10,45 2 817805-7015 10,40 4 817807-6103-11 1,20 1 12, 757807-6124-11 7,70 1 127807-6132-11 11,50 4 127807-6136-11 12,50 1 127807-7103-11 1,30 1 12, 757807-7136-11 18,10 1 12
7809-7547-01 2,70 2 84
7814-7136-11 18,10 1 15
7821-1435 2,30 4 22-237821-2935 237821-3040 2,70 1 287821-3440 2,75 4 267821-5440 2,65 1 30
7822-1526 1,85 4 227822-2526 1,30 4 207822-2726 1,30 217822-2826 237822-3526 1,45 4 26
7823-2647 4,60 1 557823-3647 4,40 1 52
7832-3301 1,20 1 115
7833-4301 1,80 1 1157833-4401 1,85 1 115
7834-3303 2,50 1 1157834-4401 2,30 1 115
7837-3301 1,00 1 115
7839-3301 1,40 1 115
7851-1308-20 2,50 20 117851-1312-20 3,60 20 117851-1316-20 4,80 20 11
7852-2309-20 3,60 20 147852-2312-20 4,60 20 147852-2315-20 5,70 20 147852-2318-20 6,90 20 147852-2324-20 9,00 20 147852-2331-20 11,50 20 14
7853-1724-20 9,50 217853-1726-20 9,99 217853-1731-20 11,74 217853-1737-20 14,06 217853-1824-20 11,60 217853-1826-20 12,50 217853-1829-20 13,76 217853-1831-20 15,00 217853-2631-20 237853-2637-20 237853-3309-20 5,80 15 527853-3312-20 6,30 15 527853-3315-20 8,00 10 527853-3318-20 9,80 10 527853-3324-30 13,20 10 367853-3331-30 16,40 10 367853-3337-30 19,70 10 367853-5109-20 6,00 15 527853-5112-20 7,50 15 527853-5115-20 9,00 15 527853-5118-20 11,00 15 527853-5131-20 17,70 15 367853-5137-20 21,70 15 367853-6224-20 9,50 15 197853-6226-20 12,50 10 197853-7631-20 15,00 15 227853-7637-20 20,00 15 22
Numerical index with weight table
TOP HAMMER DRILLING TOOLS • 127
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
7854-8637-20 23,50 15 257854-8643-20 27,00 10 257854-8649-20 30,50 10 257854-9631-20 23,10 15 257854-9637-20 27,80 15 257854-9643-20 32,80 10 257854-9649-20 37,00 10 25
7857-4821-20 6,40 20 127857-4831-20 10,00 20 12
7859-2931-20 14,50 15 16
7870-1140-11 17,10 15 87870-1144-11 13,90 15 87870-1148-11 14,80 15 87870-1156-11 17,50 15 87870-1164-11 19,80 15 87870-1172-11 22,50 50 87870-1180-11 87870-5124-11 7,92 20 87870-5132-11 10,24 20 87870-6106-11 2,28 20 87870-6112-11 4,16 20 87870-6118-11 6,04 20 87870-6120-11 6,54 20 87870-6124-11 7,92 20 87870-6131-11 9,79 20 87870-6137-11 11,40 20 8
7876-6106-11 2,20 20 97876-6108-11 2,70 20 97876-6112-11 4,10 20 97876-6118-11 5,90 20 97876-6120-11 7,80 20 97876-6124-11 7,80 20 97876-6131-11 9,60 20 97876-6136-11 11,00 20 9
790-1100 34,00 1 70790-2100 4,50 1 70790-2200 4,50 1 70790-2300 2,00 1 71790-3100 42,00 1 69790-4100 52,00 1 69790-4200 76,00 1 69790-6100 45,00 1 71
791-4101 0,03 1 69791-4102 0,05 1 69791-4103 0,05 1 69791-4105 5,00 1 69, 71
7922-6108-11 3,30 20 77922-6112-11 4,70 20 77922-6116-11 5,60 20 77922-6120-11 7,00 20 77922-6124-11 7,90 20 7
795-1336 0,01 1 105795-1336 0,01 1 112, 117795-1340 0,01 1 112795-1343 0,02 1 105, 112795-1396 0,01 1 93-94, 96, 98, 112795-1407 4,20 1 116795-1408 3,10 1 116
795-1420 5,50 1 116795-1431 3,50 1 116795-1432 3,50 1 116795-1467 1,00 1 116795-1468 0,80 1 116795-1469 4,40 1 7, 116795-1492 3,10 1 116795-1494 3,45 1 116795-1495 5,20 1 116795-1600 0,21 1 117795-1601 0,30 1 117795-1604 1,65 1 117795-1605 3,90 1 117795-1606 0,60 1 117795-1607 3,90 1 117795-1608 6,00 1 117795-1609 8,40 1 117795-1611 0,93 1 117795-1613 1,70 1 117795-1629 0,51 1 117795-1630 0,73 1 117795-1631 0,70 1 117795-1632 0,84 1 117795-1676 0,93 1 117795-1681 1,50 1 117795-1686 0,50 1 117795-1687 3,00 1 117795-1690 2,00 1 117795-1696 10,90 1 117795-1699 4,90 1 117795-1960 4,90 1 117795-1961 18,00 1 117795-1962 0,55 1 117795-1964 240,00 1 117795-2423 4,30 1 116795-2476 5,70 1 116795-2600 10,00 1 117795-2601 10,20 1 117795-2603 1 117
7953-4618-20 16,00 15 36, 527953-4631-20 24,00 15 36
7955-5618-20 24,00 10 39, 557955-5637-20 48,00 10 39
7956-6318-21 28,00 10 42, 577956-6337-70 46,00 10 427956-7637-70 77,50 1 42
7957-7618-20 40,00 10 457957-7618-20 40,00 10 597957-7637-70 76,00 1 457957-8737-70 89,00 1 45
796-1400 0,00 1 116796-1858 2,00 1 101796-1858 2,00 1 112796-1862 0,05 1 112796-1863 0,02 1 112796-1865 0,20 1 112796-1866 0,01 1 112796-1867 0,25 1 101796-2930 50,00 1 118796-2930-52 60,00 1 118796-2931 5,00 1 118796-2960-XX 120,00 1 101
Numerical index with weight table
128 • TOP HAMMER DRILLING TOOLS
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
796-3201-XX 260,00 1 101796-3231-XX 380,00 1 102796-32XX-51 380,00 1 101796-32XX-51 380,00 1 102796-32XX-52 380,00 1 101796-32XX-52 380,00 1 102796-32XX-55 380,00 1 101796-32XX-55 380,00 1 102796-32XX-56 380,00 1 101796-32XX-56 380,00 1 102796-32XX-57 380,00 1 101796-32XX-57 380,00 1 102796-32XX-58 380,00 1 101796-32XX-58 380,00 1 102796-32XX-59 380,00 1 101796-32XX-59 380,00 1 102796-32XX-60 380,00 1 101796-32XX-60 380,00 1 102796-32XX-61 380,00 1 101796-32XX-61 380,00 1 102796-32XX-65 380,00 1 101796-32XX-65 380,00 1 102796-32XX-66 380,00 1 101796-32XX-66 380,00 1 102796-3301-XX 355,00 1 103796-330X-51 355,00 1 103796-330X-52 355,00 1 103796-330X-55 355,00 1 103796-330X-56 355,00 1 103796-330X-57 355,00 1 103796-330X-58 355,00 1 103796-330X-59 355,00 1 103796-330X-60 355,00 1 103796-330X-61 355,00 1 103796-330X-65 355,00 1 103796-330X-66 355,00 1 103796-3601-XX 335,00 1 104796-360X-51 335,00 1 104796-360X-52 335,00 1 104796-360X-55 335,00 1 104796-360X-56 335,00 1 104796-360X-57 335,00 1 104796-360X-58 335,00 1 104796-360X-59 335,00 1 104796-360X-60 335,00 1 104796-360X-61 335,00 1 104796-360X-65 335,00 1 104796-360X-66 335,00 1 104796-3800 22,00 1 108796-3830 18,00 1 108796-5012-50 46,00 1 107796-5012-51 38,00 1 107796-5012-52 43,00 1 107796-5012-55 38,00 1 107796-5012-56 46,00 1 107796-5012-57 38,00 1 107796-5012-58 38,00 1 107796-5012-59 38,00 1 107796-5012-60 38,00 1 107796-5012-61 43,00 1 107796-5012-65 38,00 1 107796-5012-66 38,00 1 107796-5012-XX 38,00 1 107796-5100 2,70 1 93796-5116 2,90 1 93796-5300 18,00 1 105796-5330 16,50 1 106
796-6005-50 95,00 1 98796-6005-51 95,00 1 98796-6005-52 95,00 1 98796-6005-55 95,00 1 98796-6005-56 95,00 1 98796-6005-57 95,00 1 98796-6005-58 95,00 1 98796-6005-59 95,00 1 98796-6005-60 95,00 1 98796-6005-61 95,00 1 98796-6005-65 95,00 1 98796-6005-66 95,00 1 98796-6005-XX 95,00 1 98796-6006-XX 95,00 1 98796-6050-50 50,00 1 101796-6105-50 96,00 1 99796-6105-51 96,00 1 99796-6105-52 96,00 1 99796-6105-55 96,00 1 99796-6105-56 96,00 1 99796-6105-57 96,00 1 99796-6105-58 96,00 1 99796-6105-59 96,00 1 99796-6105-60 96,00 1 99796-6105-61 96,00 1 99796-6105-65 96,00 1 99796-6105-66 96,00 1 99796-6105-XX 96,00 1 99796-6106-XX 96,00 1 99796-6205 48,00 1 94796-6206 56,00 1 94796-6215-XX 70,00 1 96796-6216-XX 74,00 1 96796-6235 43,00 1 95796-6236 55,00 1 95796-62XX-50 1 96796-62XX-51 1 96796-62XX-52 1 96796-62XX-55 1 96796-62XX-56 1 96796-62XX-57 1 96796-62XX-58 1 96796-62XX-59 1 96796-62XX-60 1 96796-62XX-61 1 96796-62XX-65 1 96796-62XX-66 1 96796-6300 43,00 1 97796-6301 46,00 1 97796-6310-XX 65,00 1 97796-6311-XX 70,00 1 97796-6330 38,00 1 97796-6331 43,00 1 97796-63XX-50 1 97796-63XX-51 1 97796-63XX-52 1 97796-63XX-55 1 97796-63XX-56 1 97796-63XX-57 1 97796-63XX-58 1 97796-63XX-59 1 97796-63XX-60 1 97796-63XX-61 1 97796-63XX-65 1 97796-63XX-66 1 97796-9200-50 350,00 1 100796-9200-51 350,00 1 100
Numerical index with weight table
TOP HAMMER DRILLING TOOLS • 129
Part No. Weight Package Page (kg) size (pcs)
Part No. Weight Package Page (kg) size (pcs)
796-9200-52 275,00 1 100796-9200-55 350,00 1 100796-9200-56 350,00 1 100796-9200-57 350,00 1 100796-9200-58 350,00 1 100796-9200-59 350,00 1 100796-9200-60 350,00 1 100796-9200-61 350,00 1 100796-9200-65 350,00 1 100796-9200-66 350,00 1 100796-9200-XX 350,00 1 100796-9250-xx 60,00 1 100
7970-1200-xx 2,40 1 667970-1500-xx 3,00 1 667970-1600-xx 3,20 1 667970-1800-xx 3,60 1 667970-2000-xx 4,00 1 667970-2100-xx 4,20 1 667970-2400-xx 4,80 1 667970-2700-xx 5,40 1 667970-3000-xx 6,00 1 667970-3300-xx 6,60 1 667970-3600-xx 7,20 1 667970-4000-xx 8,00 1 667970-4500-xx 9,00 1 667970-5000-xx 10,00 1 667970-5500-xx 11,00 1 667970-6000-xx 12,00 1 667970-600-xx 1,20 1 667970-900-xx 1,80 1 667970-P154D 0,66 1 667970-P156 1,05 1 667970-P158 1,35 1 66
797-1100-32 4,50 1 110797-1101-25 1,85 1 110797-1101-32 2,05 1 110797-1105-48 6,80 1 110797-1105-58 8,20 1 110797-1175-35 6,70 1 110797-1175-44 6,10 1 1107971-1800-xx 6,75 1 68797-1185-28 1,60 1 110797-1190-23 3,30 1 110797-1190-26 3,70 1 110797-1190-29 4,10 1 110797-1190-32 4,50 1 110
7971-2100-xx 7,90 1 68797-1227-10 1,05 1 105797-1227-10 1,05 1 111797-1227-15 1,00 1 105, 111
7971-2400-xx 9,00 1 68797-1250-10 3,35 1 111797-1252-15 1,85 1 1117971-2700-xx 10,20 1 687971-3000-xx 11,70 1 687971-3300-xx 12,40 1 687971-3600-xx 13,50 1 687971-4000-xx 15,00 1 687971-4500-xx 17,30 1 687971-5000-xx 19,20 1 687971-5500-xx 21,10 1 687971-6000-xx 22,90 1 687971-P154D 0,66 1 67
7971-P154D 0,66 1 687971-P156 1,10 1 677971-P156 1,10 1 687971-P158 1,39 1 677971-P158 1,39 1 68
7972-1800-xx 4,86 1 677972-2100-xx 5,67 1 677972-2400-xx 6,72 1 677972-2700-xx 7,29 1 677972-3000-xx 8,10 1 677972-3300-xx 8,91 1 677972-3600-xx 9,72 1 677972-4000-xx 10,80 1 677972-4500-xx 12,15 1 677972-5000-xx 13,50 1 677972-5500-xx 14,85 1 677972-6000-xx 16,20 1 67
797-5114-03 0,10 1 116797-5130-10 14,80 1 94797-5130-10 14,80 1 96797-5130-10 14,80 1 98797-5295-07 0,04 1 109797-5295-08 0,04 1 109797-5295-09 0,05 1 109797-5295-10 0,05 1 109797-5295-11 0,05 1 109797-5295-12 0,06 1 109797-5295-13 0,06 1 109797-5295-14 0,07 1 109797-5295-16 0,08 1 109797-5330-91 2,80 1 105797-5330-92 4,20 1 105797-5348-XX 1,00 1 98797-5356-08 0,05 1 109797-5356-10 0,05 1 109797-5356-11 0,05 1 109797-5356-12 0,05 1 109797-5356-14 0,05 1 109797-5356-16 0,05 1 109797-5366-09 0,05 10 109797-5366-10 0,05 10 109797-5366-11 0,05 10 109797-5366-12 0,05 10 109797-5366-14 0,05 10 109797-5366-16 0,00 10 109797-5400-07 0,04 1 109797-5400-08 0,04 1 109797-5400-09 0,05 1 109797-5400-10 0,05 1 109797-5400-11 0,05 1 109797-5400-12 0,06 1 109797-5400-13 0,06 1 109797-5400-14 0,07 1 109797-5400-16 0,08 1 109797-5400-18 0,10 1 109797-5452 0,06 1 93-94797-5452 0,06 1 96, 98797-5488-75 4,85 1 94797-5488-75 4,85 1 96, 98797-5488-85 5,95 1 93797-5489-50 1,50 1 105797-5502-50 1,05 1 94, 96797-5503-60 1 99797-5510-05 1,00 1 94, 96797-5510-06 7,20 1 94, 96
Numerical index with weight table
130 • TOP HAMMER DRILLING TOOLS
Part No. Weight Package Page (kg) size (pcs)
797-5510-20 4,00 1 94, 96797-5510-30 2,00 1 94, 96797-5510-40 3,00 1 94, 96797-5615-xx 1 100797-5712-01 1 116797-5730-13 1 101797-5747-50 1,50 1 93, 105797-5766-06 0,07 1 105797-5771 0,04 1 101, 105797-5773-20 1,00 1 94, 96, 98, 101797-5775-20 1 108797-5870-10 1,00 1 94, 96, 98797-5870-20 0,42 1 94, 96, 98797-5870-90 1,20 1 93-94, 101797-5910-28 1,23 1 94, 96797-6015-56 1 101797-6015-60 1 101797-6020 7,00 1 101, 103, 112797-6020-23 1 112797-6020-25 0,81 1 112797-6020-28 1 112797-6020-32 1,00 1 112797-6020-33 1 112797-6020-35 1,10 1 112797-6020-38 0,00 1 112797-6020-45 1,26 1 112797-6035-06 0,24 1 101797-6035-07 0,26 1 104797-6035-08 0,23 1 104797-6035-45 0,36 1 101, 102
7985-6315-26 28,00 10 607985-6318-26 32,00 10 60
7991-2031 0,45 10 11
7993-0444 1,20 5 1157993-2443 1,05 5 1157993-3644 0,90 5 20-23, 52
7994-3455 1,90 5 1157994-3655 1,70 5 25
7999-3640 0,77 5 16, 20
Notes
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
TOP HAMMER DRILLING TOOLS • 131
Notes
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
132 • TOP HAMMER DRILLING TOOLS
Notes
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
TOP HAMMER DRILLING TOOLS • 133
Notes
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
134 • TOP HAMMER DRILLING TOOLS
Notes
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
TOP HAMMER DRILLING TOOLS • 135
Notes
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
......................................................................................................................................................................
136 • TOP HAMMER DRILLING TOOLS
Ro
ck
drillin
g to
ols
To
p h
am
me
r pro
du
cts
www.sandvik.com
Sandvik Mining and Construction Tools ABSE-811 81 Sandviken, Sweden. Tel +46 26 26 20 00 Fax +46 26 26 23 00
HR-12281-ENG AB Sandvikens Tryckeri
Top hammer drilling tools Product catalogue
Products from Sandvik Mining and Construction Tools