SAVCOR FUTURTEC OHM MOBILE

MONITORING SOLUTION

REAL-TIME, FULL STRUCTURAL HEALTH MONITORING AND COMPONENT EVALUATION

IN A MOBILE SOLUTION

Savcor OyGroup Headquarters

Insinöörinkatu 8FI-50150 Mikkeli

Finland

Tel: +358 20 774 774

www.savcor.com

FINLAND / CANADA / GERMANY / BRAZIL / RUSSIA

STARTING PAGE OF THE NEW MOBILE SOLUTION

This starting page shows the status of all components in Mobile monitoring system. User can be sure that sensors and other components are installed correctly and they are ready for measurements.

MOBILE USER INTERFACE

After the signal acquisition, signal transmission, data analyses and consolidation, Savcor Futurtec Mobile OHM provides the operator with easy to interpret and easy to use information for manual decision making or controlling directly the use or access to the asset.

KEY BENEFITS OF THE USER INTERFACE ARE:

All key information for rapid decision-making, even for a large asset is visible in an easy to understand and interpret format on one single page. Multi-level displays show real time, daily and historical data as required.

The UI100 provides fast access to detailed analyses of all important areas of the asset. All information is provided both in easy to use graphical format as well as in numerical format straightforward to export for further use in other systems.

The key benefits for operators, constructors and designers are

− Avoidance of hazardous situations and even life saving by controlling access to the monitored under construction.

− Elimination of major breakdowns through advance warning of harsh environmental conditions or propagating structural problems.

− Repair cost savings through elimination of unexpected failures.

− Maintenance cost savings through extended life of expensive components.

− Personnel cost savings and motivation improvements through reduction of unnecessary inspection and maintenance work.

Key Highlights − Complete Solution and ready to work immediately

− A wide range of sensors

− Up to 32 channels of data simultaneously

The Savcor Futurtec Mobile Monitoring Solution provides the same high quality, complete and real-time Structural Health Monitoring as the permanently installed turn-key solution on a smaller basis.

It is a unique Mobile Monitoring Solution that allows the collection of synchronized data from up to 32 channels, which can either be stored on the local server or forwarded to a remote location. In both cases it is possible to view the data real time on the Savcor Futurtec user-friendly interface. The Mobile Monitoring Solution is a complete solution with all sensors, bus cabling, mobile data handling server installed into a enclosure and is ready to be used immediately.

− The unit can be used indefinitely from mains supply through the Uninterruptible Power Supply.

− All data recorded is stored on the hard disk and can be transferred via LAN/WLAN or internet to the control room server or viewed real time.

APPLICATIONS

− Monitoring of the structures under construction.

− Calculation of residual fatigue life of existing structures

− Vibration signature collection from existing structures

− Determination of emergency maintenance requirements

− Routine structural assessment for early warning of developing maintenance requirements

Savcor Futurtec Mobile OHM consist of four main parts that are: The S100 Mobile Server (based on IP65 Laptop (Panasonic ToughBook with accessories) for data collection and analysis, the 24 bit SLS signal transmission bus that ensures that the signal quality as well as the installation and transmission costs are optimised by using a mixture of wired and wireless technologies where best suited, the measurement solution with several different types of sensors ranging from the tiniest strain gauges and tilt to weather sensor and web browser based User interface.

The S100 Mobile server collects and synchronizes all data and presents the data for display using the Savcor Futurtec OP100 and UI 100 software.

24 BIT SLS SIGNAL TRANSMISSION BUS The same high precision A/D converters and data transport solution that are used in the permanently installed Solutions. Signals are converted to digital format by the SLS Nodes and are accurately synchronized and conveyed through one bus cable (segment) allowing safer, cleaner data transmission as well as the simplest installation available in the industry.

Controller module handles one measurement segment with several SLS Nodes and sensors. It provides the operating voltage to the SLS Nodes and sensors as well as handles the data transmission and synchronization of the SLS Nodes.

NPort 5110 serial device server handles one measurement segment with several SLS Nodes and sensors.

AD1 SLS Nodes are used for converting the analogue data signals into digital format for transmission in the SLS Bus.

Bus cable is in compliance with EU LVD (Low Voltage Directive 73/23/EEC), as amended by directive 93/68/EEC.

S100 MOBILE SERVER

Input Channels 32 – channels, up to three segments

Sampling Rate Sensor calibrated, from 0.01Hz to 100Hz

Memory Size Gb with expansion available

Operating Temperature -50°C to +70 °C

Casing material IP 65 Tough Book + heavy duty Explorer case

Software OS 100 Operating System, UI 100 user friendly interface and AP100 application package

Cables Complete set of cables with connectors

SAVCOR FUTURTEC OHM MOBILE

MONITORING SOLUTION

REAL-TIME, FULL STRUCTURAL HEALTH MONITORING AND COMPONENT EVALUATION

IN A MOBILE SOLUTION