sdc
DESCRIPTION
hjngghhhjTRANSCRIPT
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 1
Semiconductor Devices & Circuits
SE (E&TC) SEM-I
Laboratory Notebook
Department of Electronics & Telecommunication
R C Patel Institute of Technology, Shirpur
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 2
The Shirpur Education Societys
R. C. Patel Institute of Technology, Shirpur
CERTIFICATE
This is to certify that Mr / Miss ________________________________Of SecondSecondSecondSecond
YearYearYearYear Electronics & TelecommunicationElectronics & TelecommunicationElectronics & TelecommunicationElectronics & Telecommunication branch, Roll No. ______Has performed practical
work satisfactorily in the Subject Semiconductor Devices & CircuitSemiconductor Devices & CircuitSemiconductor Devices & CircuitSemiconductor Devices & Circuit, in the premises of the
Department of Electronics & Telecommunication Engineering during the academic year
20 -20 .
Date: / / 20 Signature of the Teacher
Place: Shirpur
Principal Head of Department
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 3
CONTENTS
Expt No Experiment Title Page No
1 For a half wave rectifier with capacitor filter find line and load regulation and ripple factor.
4
2 For full wave rectifier with capacitor filter find line and load regulation and ripple factor.
13
3 For Bridge wave rectifier with capacitor filter find line and load regulation and ripple factor.
23
4 Square wave testing of an amplifier used to find lower and higher cut off frequency.
31
5 For two cascaded CE-CE stages, find voltage gain and bandwidth.
36
6 For two stage cascode (CE-CB) amplifier determine voltage gain and bandwidth.
43
7 Determine I/P and O/P impedances and voltage gain of a CE stage followed by CC.
49
8 Study the effect of bypass capacitor on frequency response of single stage CE amplifier
55
9 Study frequency response of CSFET
61
10 Determine I/P and O/P impedances and voltage gain and current gain for CSFET.
67
11 Plot characteristics of CSFET. Determine amplification factor, transconductance and dynamic resistance
72
12 Determine H-parameters
78
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 4
Laboratory Report
Experiment No.1
Batch Code: __________________
Name of Student: ____________________________________________ Roll No. ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [2]
a) Pre lab work done (if any) [1] ___________
b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ___________
3) Oral [1] ___________
Overall Marks ___________
Sign of practical In-charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 5
Experiment No.1
Objective: To plot regulation characteristics of Half Wave Rectifier.
Pre-lab: What is a rectifier? Definition of Ripple factor, TUF, Rectification efficiency
Equipments needed:
Sr.No Name of Equipments Specifications Quantity 1 Experiment kit 1 2 Power Supply 0-30V DC 1 3 Auto transformer 1
4 CRO 20 MHz Dual channel
1
5 Digital Multimeter 1
Theory:
Rectifier is defined as an electronic device used for converting AC voltage to DC voltage.
Half Wave Rectifier: It converts an AC voltage to pulsating DC voltage, using only
one half cycle of the applied AC voltage. The rectifying diode conducts only during one half of the AC cycle only.
Let Vi be the voltage of the primary of the transformer and given by equation-
Vi = Vm sinwt Vm>>Vr
Where Vr is the cut-off voltage of the diode.
During positive half cycle of the input signal, the anode of the diode becomes more positive w.r.t. cathode and hence diode conducts. For the ideal diode the forward bias voltage drop is zero and hence the input half appears at the output (as diode acts as a closed switch.)
During negative half cycle of the input signal, the anode becomes negative and cathode is at positive, hence diode becomes reverse bias in which it acts as an open switch. During the negative half cycle no input appears at the o/p. When capacitor is used as filter, then it is connected across the load resistor. The Property of the capacitor is that
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 6
it allows to pass only AC components present in o/p and blocks the DC. As the o/p across the load resistor is not constant but it contains Positive half cycles only, during positive half cycle capacitor charges and when the Negative half cycle appears for which no o/p is obtained, due to charged capacitor Voltage across capacitor remains always constant.
Procedure: A) For with capacitor filter: (Short points A & C) 1. Trace and draw the circuit diagram. 2. For load regulation ammeter is connected between points A and B.Voltmeter is Connected between point B and Ground. Vary load resistor RL and note readings Of voltage VL and current IL. 3. For line regulation, Voltmeter is connected between point B and ground. Vary Supply voltage through auto-transformer and note readings of supply voltage Vi And o/p voltage Vo. At that time keep RL constant. 4. For ripple factor, short A and B, connect CRO between B to ground at constant load and measure Vm on CRO. 5. Draw the waveforms on the graph paper.
B) For without capacitor filter: (Open points A & C) 1. Trace and draw the circuit diagram. 2. For load regulation ammeter is connected between points A and B.Voltmeter is connected between point B and Ground. Vary load resistor RL and note readings of voltage VL and current IL. 3. For line regulation, Voltmeter is connected between point B and ground. Vary Supply voltage through auto-transformer and note readings of supply voltage Vi And o/p voltage Vo. At that time keep RL constant. 4. For ripple factor, short A and B, connect CRO between B to ground at
Constant load and measure Vm on CRO. 5. Draw the waveforms on the graph paper.
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 7
Observation Table: Line Regulation (Without Capacitor Filter):
Line Regulation (With Capacitor Filter):
Sr.NO. Vi(volts) Vo(volts) 1
2
3
4
5
6
7
8
9
10
Sr.NO. Vi(volts) Vo(volts) 1
2
3
4
5
6
7
8
9
10
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 8
Load Regulation (Without Capacitor Filter):
Sr.NO. IL(mA) VL(volts) 1 2 3 4 5 6 7 8 9
10
Load Regulation (With Capacitor Filter):
Sr.NO. IL(mA) VL(volts) 1 2 3 4 5 6 7 8 9
10
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 9
Calculations:
Load regulation=
No load voltage Full load Voltage *100 Full load voltage
Line regulation=
Vo/Vi *100
Load Regulation:
1) (Without Capacitor Filter):
2) (With Capacitor Filter):
Line Regulation:
1) (Without Capacitor Filter):
2) (With Capacitor Filter):
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 10
Result:
Type of Regulation Without capacitor filter With capacitor filter
% Load Regulation
% Line Regulation
Conclusion: _________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 11
Lab Assignment1: What is rectifier .Also give the types of rectifier?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
Lab Assignment2: What is line regulation and load regulation?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 12
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
Lab Assignment 3: What is ripple factor of HWR without capacitor filter?
Ans ----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
Conclusion: _________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 13
Laboratory Report
Experiment No. 2
Batch Code: __________________
Name of Student: _________________________________ Roll No. ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [2] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ----------------
3) Oral [1] --------------
Overall Marks ----------------
Sign of Practical In-charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 14
Experiment No. 2
Objective To plot regulation characteristics of Full Wave Rectifier.
Pre-lab: What is rectification efficiency? Expression for rectification efficiency.
Equipments needed:
Sr.No Name of Equipments Specification Quantity 1 Experiment kit 1 2 Power Supply 0-30V DC 1 3 Auto transformer 1 4 CRO 20 MHz Dual
channel 1
5 Digital Multimeter 1 6 Experiment kit 1
Theory:
Rectifier is defined as an electronic device used for converting AC voltage to DC voltage.
Full Wave Rectifier: It converts an AC voltage to pulsating DC voltage,using both half cycles of the applied AC voltage. The rectifying diode conducts during both half cycles of the AC cycle.
During positive half cycle of the input signal, the anode of the diode D1 becomes more positive w.r.t. cathode and at the same time anode of D2 becomes negative and hence diode D2 does not conduct and o/p current flows through only D1. During negative half cycle of the input signal, the anode of diode D1 becomes negative and anode of D2 becomes positive ,hence diode D1 becomes reverse bias in which it acts as an open switch and only D2 conducts and provides the load current. When capacitor is used as filter, then it is connected across the load resistor. The Property of the capacitor is that it allows to pass only AC components present in o/p
and blocks the DC. As the o/p across the load resistor is not constant but it contains Positive half cycles only which does not give constant DC o/p. During positive half Cycle capacitor charges and when the next positive half cycle appears in between this time, due to charge stored across capacitor o/p across load resistor appears almost
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 15
constant.
Procedure: A) For with filter: (Short points A & C) 1. Trace and draw the circuit diagram. 2. For load regulation ammeter is connected between points A and B. Voltmeter is Connected between point B and Ground. Vary load resistor RL and note readings of voltage VL and current IL. 3. For line regulation, Voltmeter is connected between point B and ground. Vary Supply voltage through auto-transformer and note readings of supply voltage Vi And o/p voltage Vo. At that time keep RL constant. 4. For ripple factor, short A and B, connect CRO between B to ground at constant load and measure Vm on CRO. 5. Draw the waveforms on the graph paper.
B) For without filter: (Open points A & C) 1. Trace and draw the circuit diagram. 2. For load regulation ammeter is connected between points A and B. Voltmeter is connected between point B and Ground. Vary load resistor RL and note readings of voltage VL and current IL. 3. For line regulation, Voltmeter is connected between point B and ground. Vary Supply voltage through auto-transformer and note readings of supply voltage Vi And o/p voltage Vo. At that time keep RL constant. 4. For ripple factor, short A and B , connect CRO between B to ground at Constant load and measure Vm on CRO. 5. Draw the waveforms on the graph paper.
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 16
Observation Table: Line Regulation: (Without capacitor Filter)-
Line Regulation : (With Capacitor Filter)- Sr.NO. Vi(volts) Vo(volts)
1
2
3
4
5
6
7
8
9
10
Sr.NO. Vi(volts) Vo(volts) 1
2
3
4
5
6
7
8
9
10
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 17
Load Regulation :( Without capacitor Filter)-
Sr.NO. IL(mA) VL(volts) 1
2
3
4
5
6
7
8
9
10
Load Regulation (With capacitor Filter)-
Sr.NO. IL(mA) VL(volts) 1
2
3
4
5
6
7
8
9
10
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 18
Calculations:
Load regulation=
No load voltage Full load Voltage *100 Full load voltage
Line regulation=
Vo/Vi *100
Load Regulation:
1) (Without Capacitor Filter):
2) (With Capacitor Filter):
Line Regulation:
1) (Without Capacitor Filter):
2) (With Capacitor Filter):
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 19
Result:
Type of Regulation Without capacitor filter With capacitor filter
% Load Regulation
% Line Regulation
Conclusion: ________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 20
Lab Assignment1: What is full wave rectifier? Why it is called so? Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
Lab Assignment2: Derive expression for ripple factor of a full wave rectifier with Capacitor filter?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 21
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------- ------
----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 22
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 23
Laboratory Report
Experiment No. 3
Batch Code: __________________
Name of Student: _______________________ Roll No. ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [2] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] -----------------
3) Oral [1] ---------------
Overall Marks ----------------
_
Sign of practical In-charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 24
Experiment No. 3
Objective: - To plot regulation characteristics of Bridge Wave Rectifier.
Pre-lab: What is PIV? What is PIV of BWR?
Equipments needed:-
Sr.No Name of Equipments Specification Quantity 1 Experiment kit 1 2 Power Supply 0-30V DC 1 3 Auto transformer 1 4 CRO 20 MHz Dual
channel 1
5 Digital Multimeter 1
Theory:
Rectifier is defined as an electronic circuit used for converting AC voltage to DC voltage.
Bridge Wave Rectifier: It converts an AC voltage to pulsating DC voltage, using
only one half cycle of the applied AC voltage. The rectifying diode conducts only during one half of the AC cycle only. During positive half cycle of the input signal, the point A is more positive w.r.t.
point B. The current path is point A through D1, load, D3 and backs to the point B.During this time diodes D2 and D4 are reverse bias. During negative half cycle of the input signal, the point B is More positive than
point A.The current path is point B through D2, load D4 and back to the point A.During this time D3 and D4 are reverse bias. It is interesting to note that, in both the half cycles the direction of current flow through the load is same. Thus we obtain full wave rectification, the waveform being same. When capacitor is used as filter, then it is connected across the load resistor. The Property of the capacitor is that it allows to pass only AC components
present in o/p and blocks the DC. As the o/p across the load resistor is not constant but it contains Positive half cycles only, during positive half cycle capacitor charges
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 25
and when the Negative half cycle appears for which no o/p is obtained, due to charged capacitor Voltage across capacitor remains always constant.
Procedure:
A) For with capacitor filter: (Short points A & C) 1. Trace and draw the circuit diagram. 2. For load regulation ammeter is connected between points A and B.Voltmeter is Connected between point B and Ground. Vary load resistor RL and note readings of voltage VL and current IL. 3. For line regulation, Voltmeter is connected between point B and ground. Vary Supply voltage through auto-transformer and note readings of supply voltage Vi And o/p voltage Vo. At that time keep RL constant. 4. For ripple factor, short A and B, connect CRO between B to ground at constant load and measure Vm on CRO. 5. Draw the waveforms on the graph paper.
B) For without capacitor filter: (Open points A & C) 1. Trace and draw the circuit diagram. 2. For load regulation ammeter is connected between points A and B.Voltmeter is connected between point B and Ground. Vary load resistor RL and note readings of voltage VL and current IL. 3. For line regulation, Voltmeter is connected between point B and ground. Vary Supply voltage through auto-transformer and note readings of supply voltage Vi And o/p voltage Vo. At that time keep RL constant. 4. For ripple factor, short A and B, connect CRO between B to ground at Constant load and measure Vm on CRO.
5. Draw the waveforms on the graph paper.
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 26
Observation Table: Line Regulation :( Without capacitor Filter)-
Line Regulation :(With capacitor Filter)- Sr.NO. Vi(volts) Vo(volts)
1
2
3
4
5
6
7
8
9
10
Sr.NO. Vi(volts) Vo(volts) 1
2
3
4
5
6
7
8
9
10
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 27
Load Regulation: (Without capacitor Filter)-
Sr.NO. IL(mA) VL(volts) 1 2 3 4 5 6 7 8 9
10 11
Load Regulation (With capacitor Filter)-
Sr.NO. IL(mA) VL(volts) 1 2 3 4 5 6 7 8 9
10 11
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 28
Calculations:
Load regulation=
No load voltage Full load Voltage *100 Full load voltage
Line regulation=
Vo/Vi *100
Load Regulation:
1) (Without Capacitor Filter):
2) (With Capacitor Filter):
Line Regulation:
1) (Without Capacitor Filter):
2) (With Capacitor Filter):
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 29
Result:
Types of Regulation Without capacitor filter With capacitor filter
% Load Regulation
% Line Regulation
Conclusion: _________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 30
Lab Assignment1: Differentiate between FWR and BWR.
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 31
Laboratory Report
Experiment No. 4
Batch Code: __________________
Name of Student: _______________________________________ Roll No. ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [2] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ----------------
3) Oral [1] ---------------
Overall Marks ----------------
Sign of Practical In-Charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 32
Experiment No. 4
Objective - Square wave testing of an amplifier to find lower and higher cut-off freq.
Pre-lab: Advantage of square wave testing of an amplifier. What is bandwidth?
Equipments needed:-
Sr.No Name of Equipments Specification Quantity 1 Experiment Kit
1 2 Power Supply 0-30 V DC
1 3 Function Generator Sine wave o/p
1 4 CRO 20 MHz Dual
Channel 1
5 Connecting wires
Theory:
It is the method to find out lower and higher cut off freq. of an amplifier without plotting the actual freq. curve is known as square wave testing. The reason for
choosing square wave signal can be cleared from the following. 1) If we examine the fourier series expansion of square wave , we get a series of
sinusoidal components of different magnitude and freq. .So by Square wave testing, we are checking the amplifier response for series of sinusoidal components of the different amplitudes and freq.
2) The use of square wave testing significantly less time consuming than applying a series of sinusoidal signals at diff. freqs. And magnitude to test the freq. response of the amplifier.
3) Square waveform is one which permits small distortions to stand out clearly. For upper 3db freq.:
Fh = 0.35/tr For lower 3 db freq.: FL = p* f / 100 pi
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 33
Procedure:
1) Set i/p freq. square wave to 20 mV at 1 KHz. Keep i/p freq. of square wave low
(100 Hz) for FL, observe the waveform on CRO .Calculate P and from P calculate
FL.
2) Keep i/p freq. high (10 KHz / 100 KHz)for FH ,observe waveform on CRO
Measure rise time (tr) .Calculate FH.
3) Set i/p freq. sine wave and observe the response.
Observation Table:
1) Lower cut-off freq:
Sr.NO. Freq. (Hz) V(volts) V (volts) P=V-V/V*100 FL =P*f/100pi 1
2
3
Mean FL = FL1+FL2+FL3 / 3
2) Higher cut-off freq:
Mean FH = FH1+FH2+FH3 / 3
Sr.NO. Freq. (Hz) T1 (s) T2 (s) Tr = T2-T1 FH =(0.35/tr) 1
2
3
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 34
Calculations:
Result:
Mean FL =
Mean FH =
Bandwidth = Mean FH - Mean FL
Conclusion:-----------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 35
Lab Assignment 1: What is bandwidth of an amplifier?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-------------------------------------------------------------------------
Lab Assignment 2: Explain the need of square wave testing of an amplifier?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 36
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
--------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 37
Laboratory Report
Experiment No. 5
Batch Code: __________________
Name of Student: ____________________________________________ Roll No.
Date of Lab: Date of Submission:
Evaluations
1) Lab Attendance [2] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] -----------------
3) Oral [1] ----------------
Overall Marks ----------------
Sign of Practical In-charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 38
Experiment No. 5
Objective: - Find voltage gain and bandwidth for CE-CE amplifier. Pre-lab: Compare CE, CC, and CB configuration.
Equipments needed:-
Sr.No Name of Equipments Specification Quantity 1 Experiment Kit 1 2 Power Supply 0-30 V DC 1 3 Function Generator Sine wave o/p 1 4 CRO 20 MHz Dual
Channel 1
Theory:-
If the voltage or power gain obtained from A single stage small signal amplifier is not sufficient for practical, we must have to use more than one stage of amplification to
Achieve necessary voltage and power gain. Such an amplifier is called as a multistage amplifier. A two stage amplifier is shown in fig .
In this amplifier o/p of first stage is fed as i/p to the second stage, such a connection is commonly referred to as cascading. In amplifiers, cascading is also done to achieve i/p and o/p impedances for specific applications.
A multistage amplifier having two or more stages of CE amplifier is called as cascaded amplifier. So overall voltage gain of the amplifier is the product of voltage gain of individual stage .Therefore we get much higher voltage in cascaded amplifier. V1 = i/p voltage of first stage V2 = o/p voltage of first stage
V3 = i/p voltage of second stage V4 = o/p voltage of second stage Therefore Av1 = V2/V1 Av2 = V4/V3
Overall voltage gain = Av = V4/V1 AVS = V4/V3 * V2/V1
Avs = Av2 * Av1
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 39
Observation Table: Vi = 20mV
Sr.No. Freq. Output(Vo) Voltage gain (Vo/Vi) 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 40
Calculations:
Bandwidth = FH - FL
Result: -----------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
____________________
________________
28
29
30
31
32
33
34
35
36
37
38
39
40
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 41
Conclusion: --------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
Lab assignment 1: What is the need of using multistage amplifier?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-------------------------------------------------------------------------
Lab assignment 2: Write down expressions for Av, Ri and Ro of CE amplifier
with and without emitter resistance.
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 42
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-------------------------------------------------------------------------
Lab assignment 3: Compare CE, CC, CB configuration on the basis of Av ,Ai ,Ri and Ro
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 43
Laboratory Report
Experiment No. 6
Batch Code: __________________
Name of Student: ____________________________________________ Roll No. ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [4] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ----------------
3) Oral [1] ---------------
Overall Marks ----------------
Sign of Practical In-charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 44
Experiment No. 6
Objective: - Find voltage gain and bandwidth for CE-CB Cascode amplifier. Pre-lab: What is difference between Cascade and cascode amplifier?
Equipments needed:-
Sr.No Name of Equipments Specification Quantity 1 Experiment Kit 1 2 Power Supply 0-30 V DC 1 3 Function Generator Sine wave o/p 1 4 CRO 20 MHz Dual
Channel 1
Theory:
Multistage Amplifier: If the voltage or power gain obtained from A single stage small signal amplifier is not sufficient for practical, we must have to use more than one
stage of amplification to achieve necessary voltage and power gain. Such an amplifier is called as a multistage amplifier. A two stage amplifier is shown in fig .
In this amplifier o/p of first stage is fed as i/p to the second stage, such a Connection is commonly referred to as cascading. In amplifiers, cascading is also done to achieve i/p and o/p impedances for specific applications. Depending upon the type of amplifier, used in individual stages, multistage amplifiers can be classified into several types. A multistage amplifier having two or more stages of CE amplifier is called as Cascaded amplifier. A multistage amplifier with CE as a first stage and CB as a second Stage is called cascade amplifier. It is one approach to solve the low impedance problem of CB circuit. The cascade amplifier gives high i/p impedance stage of a CE amplifier stage as well as good voltage gain and high freq. performance of CB circuit.
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 45
Observation Table: Vi = 20mV
Sr. No. Freq. Output(Vo) Voltage gain (Vo/Vi) 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 46
Calculations:
Bandwidth = FH - FL
Result: -----------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
____________________
________________
27
28
29
30
31
32
33
34
35
36
37
38
39
40
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 47
Conclusion: -------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------
Lab assignment 1: What is the need of using multistage amplifier? What is Cascode
amplifier?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
------------------------------------------------------------------------- ------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 48
Laboratory Report
Experiment No. 7
Batch Code: __________________
Name of Student: ____________________________________________ Roll No: ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [4] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ----------------
3) Oral [1] ---------------
Overall Marks ----------------
Sign of Practical In-Charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 49
Experiment No. 07
Objective: - Determine i/p , o/p impedance and voltage gain of CE stage followed by CC Stage. Pre-lab: Need of multistage amplifier.
Types of coupling in multistage amplifier
Equipments needed:-
Sr.No Name of Equipments Specification Quantity 1 Experimental Kit
1 2 Power Supply 0-30 V DC 1 3 Function Generator Sine wave o/p 1 4 CRO 20 MHz Dual
Channel 1
Theory:
If the voltage or power gain obtained from A single stage small signal amplifier is not sufficient for practical, we must have to use more than one stage of amplification to
achieve necessary voltage and power gain. Such an amplifier is called as a multistage amplifier. A two stage amplifier is shown in fig .
In this amplifier o/p of first stage is fed as i/p to the second stage, such a connection is commonly referred to as cascading. In amplifiers, cascading is also done to achieve i/p and o/p impedances for specific applications. A multistage amplifier having two or more stages of CE amplifier is called as cascaded amplifier.
Analysis of amplifier: For Second Stage:
Current gain: Current gain of the particular stage is given by-
AI = -hf 1 + ho ZL
And that for CE amplifier with unbypassed RE is given by, For the second stage ZL = RE2 and the current gain of the second stage is,
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 50
AI2 = -Ie2 - hfe =
Ib2 1 + hoc RE2
The i/p impedance Ri of the particular stage is given by,
Ri = hi + hr AI ZL
For the second stage,
Ri2 = hic + hrc AI ZL
Thus ,the CC stage has a high i/p impedance.
The voltage gain of a particular stage is
Av = AI ZL Zi
For Second stage
Av2 = Vo = Ai2 Re2 V2
The first stage
RL1 = RC1 II RB
Current gain,
AI1 = -Ic1 = - hfe Ib1 1+ hoe RL1
The i/p impedance of the first stage, which is also the i/p impedance of the cascaded
Amplifier is, Ri1 = hie + hre AI1 RL1
The voltage gain of the first stage is , AV1 = V2 = AI1 RL1 V1 Ri1
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 51
The o/p admittance of the first transistor Q1, Yo1 = hoe - hfe *hre hie + Rs
The o/p impedance of the first stage, Ro1 = 1/Yo1
The o/p impedance taking Rc1 into account is Rot1 = Ro1 II Rc1
The o/p admittance of the second stage, Yo2 = hoc hfc * hrc hic + Rot1
o/p impedance, Ro2 = 1/Yo2
The amplifier o/p impedance taking RE2 into account is Ro2II RE2
Hence, Ro2 = Ro2 * RE2 Ro2+Re2
The overall voltage gain taking the source impedance into account,
Avs = - Vo = Av Ri1 Vs Ri1 + Rs
Result:
1) Av =
2) Ri =
3) Ro =
Conclusion:________________________________________________________________________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 52
Lab Assignment: Differentiate CE, CC, CB amplifiers on the basis of Av, Ai, Ri and Ro.
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 53
Laboratory Report
Experiment No. 8
Batch Code: __________________
Name of Student: ____________________________________________ Roll No. ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [2] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ----------------
3) Oral [1] ---------------
Overall Marks ----------------
Sign Practical In-Charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 54
Experiment No. 08
Objective: Study the Effect of bypass Capacitor on Frequency Response of Single Stage
CE Amplifier. Pre-lab: What is frequency response? Need of coupling and bypass capacitors
Equipments needed:-
Sr.No Name of Equipments Specification Quantity 1 Experimental Kit
1 2 Power Supply 0-30 V DC 1 3 Function Generator Sine wave o/p 1 4 CRO 20 MHz Dual
Channel 1
Theory:
The bypass capacitor is connected across the emitter resistance RE in BJT amplifier as shown in figure.
1. At medium and high freq. the bypass capacitor CE offers a very low reactance. Therefore it can be replaced by a short circuit as shown fig. Therefore the Impedance ZE which is the parallel combination of RE and XCE will have a Zero .value. Thus RE is bypassed successfully and the bypass capacitor CE has no effect On the freq. response of the amplifier at medium and high freq.
2. But, at low freq. the reactance XCE is not equal to zero,butit has some finite Value. Thus the parallel combination of RE and CE will offer a finite Impedance.So RE is not properly bypassed.
3. Let the impedance of parallel combination be denoted by RE 4. We know that the gain of the CE amplifier with bypassed RE is given by AV= - hfe RL
hie
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 55
And that for CE amplifier with unbypassed RE is given by, Av = -hfe RL/hie+(1+hfe)RL So if RE is not properly bypassed then voltage gain will decrease.
Procedure: 1. Trace and draw circuit diagram as shown in Fig. 2. Set supply voltage of +10V. DC input, at input 20mV and 1000Hz. 3. See the output on CRO when XY open i.e. without bypass capacitor effect and
note down it, then find out voltage gain for the same. 4. See the output on CRO when XY shorted i.e. with bypass capacitor effect and
note down it, then find out voltage gain for the same. 5. Then select the position when XY open and vary the freq. from 10 Hz to 1MHz. 6. Repeat the step-5, when XY is shorted.
Observation Table:
When X-Y is Open - Without bypass capacitor When X-Y short - With bypass capacitor
S N Freq. Output voltage Voltage gain X-Y open
(Without bypass) X-Y short
(Withbypass) X-Y open
(Without bypass) X-Y short
(Withbypass) 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 56
Calculations:
Result:
__________________________________________________________________________________________
__________________________________________________________________________________________
_________________________________________________________________________________________
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 57
Conclusion __________________________________________________________________________________________
__________________________________________________________________________________________
_________________________________________________________________________________________
Lab Assignment 1: What is the effect of bypass capacitor on freq.?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------
Lab Assignment 2: What is a feedback amplifier?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 58
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 59
Laboratory Report
Experiment No. 9
Batch Code: __________________
Name of Student: ____________________________________________ Roll No: ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [4] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ----------------
3) Oral [1] ---------------
Overall Marks ----------------
Sign of Practical In-Charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 60
Experiment No. 9
Objective: - To plot frequency response of FET amplifier and find bandwidth.
Pre-lab: What is Frequency response and bandwidth of an amplifier?
Equipments needed:-
Sr.No Name of Equipments Specification Quantity 1 Experiment Kit 1 2 Power Supply 0-30 V DC 1 3 Function Generator Sine wave o/p 1 4 CRO 20 MHz Dual
Channel 1
Theory:
FET Amplifiers: FET amplifiers provide an excellent voltage gain with the added advantage of high input impedance. There are three basic FET circuit configurations as follows:
1. Common Source 2. Common Drain
3. Common Gate.
The common source amplifier which provides good voltage amplification is most frequently used. The common drain amplifier with high i/p impedance and nearly unity voltage gain is used as buffer amplifier and the common gate amplifier is used as high freq. amplifier. The small signal current source model for FET in CS configuration. In Common source amplifier source resistor is used to set the Q-point but bypassed by capacitor for mid-freq. operation.
Procedure: 1) Trace and draw the ckt.dia. 2) Apply 20 V DC using power supply. 3) Set the sinusoidal i/p 50mV at 1 KHz from function generator.
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 61
4) Observe output on CRO & measure amplitude of output. 5) Vary i/p freq. from 10Hz to 1 MHz and note down readings for each freq. 6) Draw graph of freq. vs gain & calculate BW.
Observation Table:
Sr.No
Freq. Output(Vo) Voltage gain(Vo/Vi)
Sr.No
Freq. Output(Vo) Voltage gain(Vo/Vi)
1 23
2 24
3 25
4 26
5 27
6 28
7 29
8 30
9 31
10 32
11 33
12 34
13 35
14 36
15 37
16 38
17 39
18 40
19 41
20 42
21 43
22 44
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 62
Calculations:
Result: ___________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Conclusion: _________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Lab Assignment 1. - In which region Q-point of FET is located? Why?
Ans:-----------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 63
----------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------
Lab Assignment 2. - Draw V-I characteristics of CSFET.
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 64
Laboratory Report
Experiment No. 10
Batch Code: __________________
Name of Student: ____________________________________________ Roll No. ____________
Date of Lab: ______________________ Date of Submission: ____________________
Evaluations
1) Lab Attendance [2] a) Pre lab work done (if any) [1] ___________ b) Records of Lab Notebook [1] ___________
2) Observations and Conclusion [2] ----------------
3) Oral [1] ---------------
Overall Marks ----------------
Sign Practical In-Charge
-
RCPIT, Shirpur Department of E&TC
Semiconductor Devices & Circuits 65
Experiment No. 10
Objective: Determine input, output impedances and voltage gain for common source FET amplifier.
Pre-lab: Compare BJT and FET. Construction of FET.
Equipments needed: Sr.No Name of Equipments Specification Quantity
1 Experiment kit 1 2 Power Supply 0-30V DC 1 3 Auto transformer 1 4 CRO 20 MHz Dual
channel 1
5 Digital Multimeter 1
Theory:
FET Amplifiers: FET amplifiers provide an excellent voltage gain with the added a