s.d.m college of engineering and technologysdmcse2006.pbworks.com/f/2sd06cs085.pdf ·...
TRANSCRIPT
1
VISHVESHWARAIAH TECHNOLOGICAL UNIVERSITY
S.D.M COLLEGE OF ENGINEERING AND TECHNOLOGY
A seminar report on
Orthogonal Frequency Division Multiplexing
(OFDM)
Submitted by
Sandeep Katakol
2SD06CS085 8th semester
DEPARTMENT OF COMPUTER SCIENCE ENGINEERING 2009-10
2
VISHVESHWARAIAH TECHNOLOGICAL UNIVERSITY
S.D.M COLLEGE OF ENGINEERING AND TECHNOLOGY
DEPARTMENT OF COMPUTER SCIENCE ENGINEERING
CERTIFICATE
Certified that the seminar work entitled “Orthogonal Frequency Division Multiplexing (OFDM)” is a bonafide work presented by Sandeep Katakol bearing USN NO:2SD06CS085 in a partial fulfillment for the award of degree of Bachelor of Engineering in Computer Science Engineering of the Vishveshwaraiah Technological University, Belgaum during the year 2009-10. The seminar report has been approved as it satisfies the academic requirements with respect to seminar work presented for the Bachelor of Engineering Degree.
Staff in charge H.O.D
CSE
Name: Sandeep Katakol
3
USN: 2SD06CS085
INDEX
1. INTRODUCTION 4
2. MULTIPLEXING 4
2.1 TDMA 5
2.2 CDMA 5
2.3 FDMA 6
3. OFDM 6
4. DATA TRANSMISSION USING MULTIPLE CARRIERS 8
5. GUARD TIME AND CYCLIC EXTENTION 10
6. TRANSMISSION AND RECEPTION 10
7. CHOICE OF OFDM PARAMETERS 11
8. ADVANTAGES 12
9. DISADVANTAGES 14
10. CONCLUSION 14
4
Orthogonal Frequency Division Multiplexing
(OFDM)
ABSTRACT A number of new technologies are being combined by the telecommunications
industry as it prepares for the next generation of mobile services. One of the key changes
is the choice of OFDM for the air interface. This paper will describe OFDM and show
why it has the ability to improve the spectral efficiency of digital radio links Orthogonal
frequency division multiplexing (OFDM) is a special case of multicarrier transmission,
where a single datastream is transmitted over a number of lower rate subcarriers.
1. INTRODUCTION In today’s world cell phone have become the single greatest tool in day today life. It has become
a necessity that business associates should be able to communicate on the go. That’s why it has become
so important to make choices in choosing which handheld device one should go for. A handheld device
is selected according to its features and benefits, like does it provide access to internet and email or does
it look slick and more. An important question when designing and standardizing cellular systems is the
selection of the multiple access schemes. There are three basic principles in multiple access, FDMA
(Frequency Division Multiple Access), TDMA (Time Division Multiple Access), and CDMA (Code
Division Multiple Access). All three principles allow multiple users to share the same physical channel
Orthogonal frequency division multiplexing (OFDM) is a communications technique that divides
a communications channel into a number of equally spaced frequency bands. A subcarrier carrying a
portion of the user information is transmitted in each band. Each subcarrier is orthogonal (independent
of each other) with every other subcarrier, differentiating OFDM from the commonly used frequency
division multiplexing (FDM).
2. MULTIPLEXING Multiplexing is the set of techniques that allows the simultaneous transmission of multiple
signals across a single data link. As data and telecommunications use increases, so does traffic. We can
accommodate. This increase by continuing to add individual links each time a new channel is needed.
In a multiplexed system, n lines share the bandwidth of one link. Figure shows the basic format
of a multiplexed system. The lines on the left direct their transmission streams to a multiplexer (MUX),
which combines them into a single stream (many-to- one).
At the receiving end, that stream is fed into a demultiplexer (DEMUX), which separates the stream
back into its component transmissions (one-to-many) and directs them to their corresponding lines. In
the figure, the word link refers to the physical path. The word channel refers to the portion of a link that
carries a transmission between a given pair of lines. One link can have many (n) channels.[1]
5
2.1 TDMA: Time Division Multiplex Access is a type of multiplexing where two or more channels of
information are transmitted over the same link by allocating a different time interval for the transmission
of each channel.
One major disadvantage using TDMA technology is that the users has a predefined time slot.
When moving from one cell site to other, if all the time slots in this cell are full the user might be
disconnected. Another problem in TDMA is that it is subjected to multipath distortion.[1]
2.2 CDMA CDMA gives the user entire spectrum all of the time. CDMA spread spectrum technology in
which it uses unique spreading codes to spread the baseband data before transmission. The receiver then
dispreads the wanted signal, which is passed through a narrow band pass filter. The unwanted signals are
not dispread and will not be passed through the filter. The codes are a sequence of zeros and ones
produced at a much higher rate of that of the baseband data.
One major problem in CDMA technology is channel pollution, where signals from too many cell
sites are present in the subscriber’s phone but none of them is dominant. When this situation arises the
quality of the audio degrades[1]
6
2.3 FDMA
In frequency-division multiple access (FDMA), the available bandwidth is divided into
frequency bands. Each station is allocated a band to send its data. In other words, each band is reserved
for a specific station, and it belongs to the station all the time. FDMA specifies a predetermined
frequency band for the entire period of communication. This means that stream data (a continuous flow
of data that may not be packetized) can easily be used with FDMA. [1]
3. OFDM
OFDM represents a different system-design approach. It can be thought of as a combination of
modulation and multiple-access schemes that segments a communications channel in such a way that
many users can share it. Whereas TDMA segments are according to time and CDMA segments are
according to spreading codes, OFDM segments are according to frequency. It is a technique that divides
the spectrum into a number of equally spaced tones and carries a portion of a user's information on each
tone. A tone can be thought of as a frequency, much in the same way that each key on a piano represents
a unique frequency. OFDM can be viewed as a form of frequency division multiplexing (FDM),
however, OFDM has an important special property that each tone is orthogonal with every other tone.
FDM typically requires there to be frequency guard bands between the frequencies so that they do not
7
interfere with each other. OFDM allows the spectrum of each tone to overlap, and because they
areorthogonal, they do not interfere with each other. By allowing the tones to overlap, the overall
amount of spectrum required is reduced.
OFDM is a modulation technique in that it enables user data to be modulated onto the tones. The
information is modulated onto a tone by adjusting the tone's phase, amplitude, or both. In the most basic
form, a tone may be present or disabled to indicate a one or zero bit of information, however, either
phase shift keying (PSK) or quadrature amplitude modulation (QAM) is typically employed.
An OFDM system takes a data stream and splits it into N parallel data streams, each at a rate 1/N
of the original rate. Each stream is then mapped to a tone at a unique frequency and combined together
using the inverse fast fourier transform (IFFT) to yield the time-domain waveform to be transmitted.
For example, if a 100-tone system were used, a single data stream with a rate of 1 megabit per second
(Mbps) would be converted into 100 streams of 10 kilobits per second (kbps). By creating slower
parallel data streams, the bandwidth of the modulation symbol is effectively decreased by a factor of
100, or, equivalently, the duration of the modulation symbol is increased by a factor of 100. Proper
8
selection of system parameters, such as the number of tones and tone spacing, can greatly reduce, or
even eliminate, ISI, because typical multipath delay spread represents a much smaller proportion of the
lengthened symbol time. Viewed another way, the coherence bandwidth of the channel can be much
smaller, because the symbol bandwidth has been reduced. The need for complex multi-tap time-domain
equalizers can be eliminated as a result.
OFDM can also be considered a multiple-access technique, because an individual tone or groups
of tones can be assigned to different users. Multiple users share a given bandwidth in this manner,
yielding the system called OFDMA. Each user can be assigned a predetermined number of tones when
they have information to send, or alternatively, a user can be assigned a variable number of tones based
on the amount of information that they have to send. The assignments are controlled by the media access
control (MAC) layer, which schedules the resource assignments based on user demand. OFDM can be
combined with frequency hopping to create a spread spectrum system, realizing the benefits of
frequency diversity and interference averaging previously described for CDMA. In a frequency hopping
spread spectrum system, each user's set of tones is changed after each time period (usually
corresponding to a modulation symbol). By switching frequencies after each symbol time, the losses due
to frequency selective fading are minimized. Although frequency hopping and CDMA are different
forms of spread spectrum, they achieve comparable performance in a multipath fading environment and
provide similar interference averaging benefits.
OFDM therefore provides the best of the benefits of TDMA in that users are orthogonal to one
another, and CDMA, as previously mentioned, while avoiding the limitations of each, including the need
for TDMA frequency planning and equalization, and multiple access interference in the case of CDMA.
4. DATA TRANSMISSION USING MULTIPLE CARRIERS An OFDM signal consists of a sum of subcarriers that are modulated by using phase shift keying (PSK)
or qudrature amplitude modulation (QAM). In the following example, all subcarriers have the phase
and amplitude, but in practice the amplitudes and phases may be modulated differently for each
subcarrier. Note that each subcarrier has exactly an integer number of cycles in the interval T , and the
number of cycles between adjacent subcarries differs by exactly one. This properly accounts for the
orthogoality between subcarriers.
9
The orthogonality of different OFDM subcarriers can also be demonstrated in another way.If each
OFDM symbol contains subcarriers that are nonzero over a T -seconds interval.Then it has which has
zeros for all frequencies f that are an integer multiple of 1/T . This effect is shown in figure which
shows the overlapping sinc spectra of individual subcarriers. At the maximum of each subcarrier
spectrum, all other subcarrier spectra are zero. Because an OFDM receiver calculates the spectrum
values at those points that correspond to the maxima of individual subcarrier, it can demodulate each
subcarrier free from any interference from the other subcarriers. Basically, below Figure shows that the
OFDM spectrum fulfills Nyquist’s criterion for an inter symbol interference free pulse shape. Notice
that the pulse shape is present in frequency domain and note in the time domain, for which the Nyquist
criterion usually is applied. Therefore, instead of intersymbol interference (ISI), it is intercarrier
interference (ICI) that avoided by having the maximum of one subcarrier spectrum correspond to zero
crossing of all the others
10
5. GUARD TIME AND CYCLIC EXTENTION
One of the most important reasons to do OFDM is the efficient way it deals with multipath delay
spread. By dividing the input data stream in N subcarriers, the symbol duration is made N times smaller,
which also reduces the relative multipath delay spread, relative to symbol time, by the same factor. To
eliminate intersymbol interference almost completely, a guard time is introduced for each OFDM
symbol. The guard time is chosen larger than the expected delay spread, such that multipath components
from one symbol cannot interfere with the next symbol. The guard time could consist of no signal at all.
In that case, however, the problem of intercarrier (ICI) would arise. ICI is crosstalk between different
subcarriers,which means they are no longer orthogonal. This effect is illustrated in figure in this
example, a subcarrier 1 and a delayed subcarrier 2 are shown. When an OFDM receiver tries to
demodulate the first subcarrier, it will encounter some interference from the second subcarrier, because
within the FFT interval, there is no integer number of cycles difference between subcarrier 1and 2. At
the same time, there will be crosstalk from the first to the second subcarrier for the same reason. To
eliminate ICI, the OFDM symbol is cyclically extended in the guard time, as shown in figure. This
ensures that delayed replicas of the OFDM symbol always have an integer number of cycles within the
FFT interval, as long as the delay is smaller than the guard time. As result, multipath signals with delays
smaller than the guard time cannot cause ICI.
11
6. TRANSMISSION AND RECEPTION
OFDM modulation divides a broadband channel into many parallel subchannels. This makes it a
very efficient scheme for transmission in multipath wireless channels. The use of an FFT/IFFT pair for
modulation and demodulation make it computationally efficient as well.
12
The transmitted signals arrive at the receiver after being reflected from many objects. Sometimes
the reflected signals add up in phase and sometimes they add up out of phase causing a “fade”. This
causes the received signal strength to fluctuate constantly. Also, different subchannels are distorted
differently as shown in Figure . An OFDM receiver has to sense the channel and correct these distortions
on each of the subchannels before the transmitted data can be extracted. OFDM is effective in correcting
such frequency selective distortions. OFDM has many advantages over other transmission techniques.
One such advantage is high spectral efficiency (measured in bits/sec/Hz). The “Orthogonal” part of the
name refers to a precise mathematical relationship between the frequencies of the subchannels that make
up the OFDM system. Each of the frequencies is an integer multiple of a fundamental frequency. This
ensures that even though the subchannels overlap they do not interfere with each other. This results in
high spectral efficiency. The use of IFFT and FFT for modulation and demodulation results in
computationally efficient OFDM modems.[3]
13
7. CHOICE OF OFDM PARAMETERS The choice of various OFDM parameters is a tradeoff between various, often conflicting
requirements. Usually, there are three main requirements to start with: bandwidth, bit rate, and delay
spread. The delay spread directly dictates the guard time. As a rule, the guard time should be about two
to four times the root-mean-squared delay spread. This value depends on the type of coding and QAM
modulation. Higher order QAM (like 64-QAM) is more sensitive to ICI and ISI than QPSK; while
heavier coding obviously reduces the sensitivity to such interference. Now the guard time has been set,
the symbol duration can be fixed. To minimize the signal-to-noise ratio (SNR) loss caused by guard
time, it is desirable to have the symbol duration much larger than the guard time. It cannot be arbitrarily
large, however, because a larger symbol duration means more subcarriers with a smaller subcarrier
spacing, a larger implementation complexity, and more sensitivity to phase noise and frequency offset,
as well as an increased peak-to-average power ratio. Hence, a practical design choice to make the
symbol duration at least five times the guard time, which implies a 1dB SNR loss because the guard
time. After the symbol duration and guard time are fixed, the number of subcarriers follows directly as
the required –3 dB bandwidth divided by the subcarrier spacing,which is the inverse of the symbol
duration less the guard time. Alternatively, the number of subcarriers may be determined by the required
bit rate divided by the bit rate per subcarrier. The bit rate per subcarrier is defined by the modulation
type, coding rate, and symbol rate. An additional requirement that can affect the chosen parameters is
the demand for an integer number of samples both within the FFT/IFFT interval and in the symbol
interval.
8. ADVANTAGES Efficient use of spread spectrum in modulation.
It is conveniently implemented using simple FFT and IFFT.
Robust against multi-path propagation.
Robust again narrow-band interference
14
9. DISADVANTAGES Requires a more linear power amplifier.
Sensitive to frequency offset and phase noise
Accurate synchronization is required.
10. CONCLUSION This report describes the concept of OFDM with brief description of other multiplexing
technologies.It also describes data transmission in OFDM,Guard time,Cyclic prefix, Transmission and
reception techniques,and some advantages and disadvantages of OFDM.
Wireless LAN is a very important application for OFDM and the development of the standard promises
to have not only a big market but also application in many different environments.
REFERENCES [1] Data Communications and Networking - Behrouz A. Forouzan
[2] Concepts of Orthogonal Frequency Domain Modulation (OFDM)
By Dave Whipple, Agilent Technologies
[3] http://www.mimo.ucla.edu/ The Engineer’s introduction to mimo and
Mimo-ofdm
[4] The principles of OFDM By Louis Litwin and Michael Pugel