CABINET POWERED MIXING CONSOLE

USER'S MANUAL

1060SPMU-

SHS AUDIOR

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVERS (OR

BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER ALL SERVICING

TO A QUALIFIED SERVICE PERSONNEL.

This triangle on your component alerts you

to the presence of uninsulated dangerous

voltage inside the enclosure that may be

sufficient to constitute a risk of shock.

This triangle on your component alerts you

to important operating and maintenance in-

structions in this accompanying literature.

Material damage refers to damage or other adverse effects caused with respect to the home and all itsfurnishings, as well to domestic animals or pets.

Used for instructions intended to alert the user to the risk of injury or material damage should the unit beused improperly.

Do not attempt to service the product beyond that described in the user-maintenance instructions.All other servicing should be referred to quality service personnel.

The product should be serviced by qualified service personnel when:

Care should be taken so that objects do not fall and liquids are not spilled into the enclosure throughopenings.

The power supply cord of the products should be unplugged from the outlet when left unused for a long period of time.

The product should be connected to a power supply only of the type described in the operating instructionsor as marked on the rear panel of the product.

The product should be located away from heat sources such as radiators, heat resistors or other products that produce heat.

The products should be located so that its location or position does not interfere with its proper ventilation.--ment, or near a swimming pool, or the like.Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, in a wet base

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

1. The power supply cord or the plug has been damaged; or2. Objects have fallen, or liquid has been spilled into the product; or3. The product has been exposed to rain; or4. The product does not appear to operate normally or exhibits a marked change in performance; or5. The product has been dropped, or the enclosure damaged

CAUTION

1

SAFETY INSTRUCTIONS

InputImpedance

10Kohm

10Kohm

47Kohm

3Kohm

Input levelRated

-10dB

-10dB

-40dB

-60dB

Input modes

Unbalanced

Unbalanced

Balanced

Balanced

Connector

2 RCA

2 TRS

3-poles TRS

XLR

Inputs

Stereo PLAY IN

Stereo LINE IN

Mono LINE IN

MONO MIC

Input

STEREO LINE IN

MONO LINE IN

MONO MIC IN

MONO MIC IN

MONO MIC IN

MONO MIC IN

MONO MIC IN

Max gain

20dB

46dB

70dB

56dB

66dB

66dB

88dB

Output

L/R LINE OUT

L/R LINE OUT

EFFECT OUT

REC OUT

MONITOR OUT

L/R LINE OUT

L/R POWER OUT

8 kinds effects status, 24bit DSP, 48KHz sample rate

AC110V/220V; 120V; 220V; 230V Refer to the nameplate on the rear panel.

63Hz, 125Hz, 250Hz, 500Hz, 1KHz, 2KHz, 4KHz, 8KHz, 16KHz +/-12dB

HI 15KHz MID 2.5KHz LOW 80Hz max equalizing value +/-15dB

-120dB @ 150ohm , at max gain

+1dB, -2dB 20Hz ~ 20KHz

≤0.5% 20Hz ~ 20KHz

Dimension

Weight

Power consumption

DSP

Power supply

Graphic EQ

Channel EQ

Microphone preamp E.I.N

Frequency response

Total harmonic distortion

ImpedanceOutputs

600ohm

10Kohm

600ohm

600ohm

Level and Power

0dB

-10dB

0dB

0dB

2X200W2X300W

8ohm4ohm

Outputs

Stereo Effect OUT

Stereo REC OUT

Monitor OUT

L/R LINE OUT

L/R Power OUT

Connector

TRS

2 RCA

TRS

TRS

TRS

Outputs modes

Unbalanced

Unbalanced

Unbalanced

Unbalanced

Unbalanced

Rated Output

10

SPECIFICATIONS

8ohm 800WBRIDGE OUT TRS Unbalanced

480X308X290mm

21Kg

1000VA MAX

CASSETE PLAYER

POWER AMP

EFFECT PROCESSOR

REC OUT L/R

TAPE IN L/R

LINE IN L/RLINE IN L/RMIC IN

EFF SEND EFX RETLINE OUT

MIC IN

RIGHTLEFT

OUTPUT

CH BCH A

FT SW

9

CONNECTION EXAMPLE

2

BRIEF INSTRUCTION

Thank you for purchasing SPMU-1060 cabinet powered mixing console.

has seven mono input channels, two stereo line input channels and a stereo playback input channel. The output power of mixer is 2X300W@4ohms or 2X200W@8ohms, bridge mode.

For the variety level signal input and the convenience of usage, the MONO input channel has a MIC input socket, a LINE input socket and a input level attenuation switch, the stereo input channel also has a MIC input socket and a LINE input socket. Every channel has HI, MID, LOW equalization circuit, monitor output and effect output. The independent playback channel has HI, LOW equalization circuit and monitor output. There are 7-band graphic equalizer for the LEFT & RIGHT outputs and the monitor output to embellish the timbre. And the built-in digital effects processor provides 16 different kinds sound field effects.

Besides stereo PA output, this series mixer also has stereo LINE outputs, independent monitor outputs and record outputs. Furthermore, the effect signal send-return sockets have been used for the external effects processor.

The built-in power amplifier has manifold protectors and uses air cooling for heat emission. By using the working mode selector, you can choose to output stereo signals or mixing signals and monitor signals. Also the unit can working at BTL bridge mode.

This mixer has consummate functions and perfect shape. And two kinds of exterior you can choose, the wooden case with handles or the 19 inches cabinet with handles, so that you can install it everywhere you want.

SPMU-1060

Safety Instructions

Brief Instruction

Mono Input Section

Stereo Input Section

Playback Input Section

Master Control Section

Rear Panel Section

Connection Example

Specifications

1

2

3

4

5

6

8

9

10

1

2

3

4

5

6

7

8

9

10

11

MID: Controls the midrange content of the input signal, the

maximum adjustment region is 2.5KHz ±15dB.

HI: Controls the treble content of the input signal, the maximum

adjustment region is 15KHz ±15dB.

LOW: Controls the bass content of the input signal, the

maximum adjustment region is 80Hz ±15dB.

EFF: Controls the signals' level which are sent to the effect bus. The effect signals are sampled after the channel level controller and controlled by channel level controller. Adjust this knob to control the signal level when connecting a effects processor, otherwise rotate the knob to zero position.

MON: Controls the signals' level which are sent to the monitor bus. The monitor signals, which can be used as monitor output or AUX output, are sampled before the channel level controller and cannot be controlled by the channel level controller.

PAN: Controls the signal level ratio between left channel and right channel. Turn the knob to the middle position to make the signal level of left channel and right channel equal.

LEVEL: Controls the channel's output level. Please rotate the knob to zero position when the channel is not used.

PFL: Press this button to monitor the input signals of the channel by headphone. The monitor signals are sampled before the channel level controller, cannot be controlled by the channel level controller.

PAD: Pushbutton to reduce 25dB incoming signal level to avoid overload.

LINE: 1/4 inch balanced jack connector for balanced line level inputs, rated input level is -40dB ~ -15dB.

MIC: XLR electronically balanced input for microphones, rated input level is -60 ~ -35dB. +48V DC supply to all capacitor microphones when the phantom power switch is turned on.

1

2

3

4

5

6

7

8

9

10

11

MONO INPUT SECTION

3

AC~

FUSE

POWER

VO

LTA

GE

SE

LE

CTO

R

RIGHT/MON BTL LEFT/MAIN

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE WITH SAME TYPE AND VALUE FUSE INDICATED.

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF FIRE OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

TOTAL LOAD ≥ 4ohm TOTAL LOAD ≥ 4ohmTOTAL LOAD 8ohm≥

FOR PROTECTION AGAINST DAMAGE OF YOUR POWER AMPLIFIER, PLEASE DO NOT CONNECT THE RIGHT/MON OR THE LEFT/MAIN SOCKET AND THE BTL SOCKET WITH LOAD SIMULTANEOUSLY.

USE ONLY WITH 250V FUSE

220

1 2 3

4 5 6

POWER SWITCH: Turn on&off the AC mains power.

AC & FUSE: Connects the AC power and holds the fuse.

VOLTAGE SELECTOR: Selects the right voltage of your country. After you selected the right voltage, please fix the organic glass panel for preventing the damage caused by mis-operation.

BTL: Two parallel-connected sockets. When the power amplifier is working at bridge mode, these two sockets outputs PA signals, total load impedance should large than 8ohms.

LEFT/MAIN: Three parallel-connected sockets. Outputs the PA signals of left channel or the mixing PA signals of mixer's left&right channels, total load impedance should large than 4ohms.

RIGHT/MON: Three parallel-connected sockets. Outputs the PA signals of right channel or monitor channel, total load impedance should large than 4ohms.

CAUTION: FOR PROTECTION AGAINST DAMAGE OF YOUR POWER AMPLIFIER, PLEASE DO NOT CONNECT THE RIGHT/MON OR THE LEFT/MAIN SOCKET AND THE BTL SOCKET WITH LOAD SIMULTANEOUSLY.

1

2

3

4

5

6

8

REAR PANEL SECTION

8 9 10 11 12 13 14

MODE SWITCH: Power amplifier working mode selector. There are three mode for choosing.

LEFT: Left channel volume controller for controlling the mixer's left channel volume.

REC OUT: Two RCA pin jacks for stereo record signal output.

RIGHT: Right channel volume controller for controlling the mixer's right channel volume.

L/R mode: Two power amplifier's channels amplify mixer's left&right channel signals separately.

MAIN/MON mode: One of the power amplifier's channel amplify the mixing signals of mixer's left&right channels. Another power amplifier's channel amplify the mixer's monitor signals.

BTL mode: Two power amplifier's channels working at the bridge mode, amplify mixer's mixing signals of left&right channels.

MON LEVEL: Monitor output level controller for controlling the signal level of monitor output.

MAIN: Master output level controller for controlling the mixing signal level of left&right channels.

HEADPHONE: Headphone socket and volume controller for connecting the headphone and controlling its volume.

8

9

10

11

12

13

14

15 16 19 20 2117 18

FT SW: 1/4 inch jack for exclusive use pedal switch. It can control the connection of effect signal.

EFF RET: 1/4 inch jack for the LEFT & RIGHT effect signals of external effects processor input. If you connect the external effects processor, the signal of built-in effects processor will be cut off automatically.

MON OUT: 1/4 inch unbalanced jack for monitor signal output, rated output level is 0dB. This socket also can be used for other AUX output and connect external monitoring amplifier.

LINE OUT: Two 1/4 inch unbalanced jacks for LEFT and RIGHT line output, rated output level is 0dB.

POWER AMP IN: Two 1/4 inch unbalanced jacks for signal insert. When signals are inserted from these two sockets, the connection between mixing console and power amplifier will be cut off automatically, and the power amplifier will amplify the signals come from these two sockets directly.

EFF SEND: 1/4 inch jack for LEFT & RIGHT effect signals output. The signal can be use as input signal for external effects processor.

PHANTOM: Phantom power switch and indicator. Press the button to supply +48V DC to all microphone.Notice: Before turn on or turn off this switch, you must turn off the level controller of all channels. Do not unplug the MIC when this switch is turned on. Do not turn on this switch when you using an electrodynamic microphone.

15

16

19

20

21

17

18

7

MASTER CONTROL SECTION

1

2

3

4

5

6

7

8

10

9

MID: Controls the midrange content of the input signal, the

maximum adjustment region is 2.5KHz ±15dB.

HI: Controls the treble content of the input signal, the maximum

adjustment region is 15KHz ±15dB.

LOW: Controls the bass content of the input signal, the

maximum adjustment region is 80Hz ±15dB.

EFF: Controls the signals' level which are sent to the effect bus. The effect signals are sampled after the channel level controller and controlled by channel level controller. Adjust this knob to control the signal level when connecting a effects processor, otherwise rotate the knob to zero position.

MON: Controls the signals' level which are sent to the monitor bus. The monitor signals, which can be used as monitor output or AUX output, are sampled before the channel level controller and cannot be controlled by the channel level controller.

BAL: Controls the signal level ratio between left channel and right channel. Adjusting the balance of stereo sound image.

LEVEL: Controls the channel's output level. Please rotate the knob to zero position when the channel is not used.

PFL: Press this button to monitor the input signals of the channel by headphone. The monitor signals are sampled before the channel level controller, cannot be controlled by the channel level controller.

MIC: XLR electronically balanced input for microphones, rated input level is -60 ~ -35dB. +48V DC supply to all capacitor microphones when the phantom power switch is turned on.

1

2

3

4

5

6

7

8

9

10

L/MONO & R: Two 1/4 inch unbalanced jacks for stereo line input, rated input level is -10dB. If the incoming signal is MONO signal, please just use the L/MONO jack.

4

STEREO INPUT SECTION

1

2

3

4

5

6

TAPE IN: Two RCA pin jacks for stereo playback input, rated input level is -10dB.

HI: Controls the treble content of the input signal, the maximum

adjustment region is 15KHz ±15dB.

LOW: Controls the bass content of the input signal, the

maximum adjustment region is 80Hz ±15dB.

MON: Controls the signals' level which are sent to the monitor bus. The monitor signals, which can be used as monitor output or AUX output, are sampled before the channel level controller and cannot be controlled by the channel level controller.

BAL: Controls the signal level ratio between left channel and right channel. Adjusting the balance of stereo sound image.

LEVEL: Controls the channel's output level. Please rotate the knob to zero position when the channel is not used.

1

2

3

4

5

6

5

PLAYBACK INPUT SECTION

EFF SELECT: Effects selector for selecting the effect you want to play (refer to the effects table below the selector).

1

EFF SEND: Effect output level controller for controlling the effect signal level that is sent to the built-in effect processor or output from EFF SEND socket.

2

EFF TO MON: Monitor effect output level controller for controlling the effect signal level of monitor output.

3

EFF TO MAIN: Main effect output level controller for controlling the effect signal level of main output.

4

9

10

11

11

MAIN EQ: 7-band stereo graphic equalizer for equalizing the frequency of the main channel's left & right outputs.

MON EQ: 7-band stereo graphic equalizer for equalizing the frequency of the monitor output.

L/MAIN & R/MON: Two groups of indicators indicate the level of stereo line output and the output power of power amplifier. When the red indicator is lighten, the output power of power amplifier reach a maximum.

9

10

11

6

MASTER CONTROL SECTION

EFF SELECT

0 10 0 10 0 10

EFF SEND EFF TO MON EFF TO MAIN

VOL+ VOL-

USB/SD1 HALL 1

2 HALL 2

3 ROOM 1

4 ROOM 2

5 ROOM 3

6 PLATE 1

7 PLATE 2

8 PLATE 3

9 CHORUS

10 FLANGE

11 DELAY 1

12 DELAY 2

13 CHORUS/ROOM 1

14 CHORUS/ROOM 2

15 VOCAL CANCEL

16 ROTARY SPEAKER

456

1

237

8

9

10

1112 13 14

1516

1

2 3 4

5

2

8

6 7

USB PORT: quality line signal source via this port.

This unit built-in a music player, An U disk which loaded many songs easily can be a good 5

Controls for built-in MP3 player: These keys allows you operate the built-in music player. 6

Display for built-in MP3 player: built-in music playerThis LCD display shows all kinds of status of the .7

SD Card: A SD Card which loaded many songs easily can be a good quality line signal source via this port.

8