SIDE PANEL FOR 8mm FRAMELESS CONCEALED HINGE DOOR

VictoriaPlum.com0344 804 48 48

We’ve made our packaging more eco-friendly,replacing plastics with recyclable reinforced cardboard. It is just as effective at protecting your product, passing strict quality control tests

Refer to sheet 11 for relevant product codes

Decide which hand is required. Right hand opening illustrated.Change the hand by turning the side panel upside down.

1

BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION

1) General Information

2) Additional Notes

Please inspect this product upon delivery, any missing parts or manufacturing

defects must be reported immediately to the supplier. Damage or defects reported

later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID

HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.

Glass breakage claims will not be accepted after the product has been unpacked.

Please note: Aluminium is a soft metal, and undergoes a series of extrusion,

fabrication, polishing and anodising processes in order to create your finished

shower enclosure. Some light surface marks are normal, and is a result of the

manufacturing processes. Quality control has ensured that this item is of a good

standard, and is fit for purpose.

Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.

Note: this product is heavy and may require two people to install.

TOOLS REQUIRED

This product is heavy and may require two people to install.

Ø3mm Drill bit

Ø6mm Drill bit

Pencil

Spirit level

Tape measure

DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE

Drill

Flat-headScrewdriver

Cross headScrewdriver

Silicone Sealant

PZ1

Mallet

2

(1)

(2)

(3)

(4)

(7)

(5)

(8)

(6)

(9)

(1) 1x Glass clamp

(2) 1x Upright profile top cap

(3) 1x Wall profile

(4) 1x Wall profile cover strip

(7) 4x Wall plugs

(5) 1x Fixed panel

(8) 4x Screws 4*30

(6) 2x Magnet seals

(9) 3x Screws 4*12

PACK I.D

E

E

B

B

E

A

E

C

E

ASSEMBLY INSTRUCTIONS - DRAWING+SIDE PANELNB: ALL MEASUREMENTS + COMPONENT SIZES QUOTED ARE IN MM.

3

BOX CONTENTS

Component

(1) 1x Glass clamp

(2) 1x Upright profile top cap

(3) 1x Wall profile

(4) 1x Wall profile cover strip

(5) 1x Fixed panel

(6) 2x Magnet seals

(7) 4x Wall plugs

(8) 4x Screws 4*30

(9) 3x Screws 4*12

PACK I.D

E

E

B

B

A

C

E

E

E

Picture

THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.

ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber .

FITTED DOOR AND SIDE PANEL DRAWING

Installation Steps7

60/

80

0/9

0/

10

00

900/ 1000/ 1200/ 1400

20

02

0

4

STEP 1 CHECK BOX CONTENTS ARE CORRECT AND THEN MEASURE KEY COMPONENTS.

STEP 2 DRAWING TO SHOW CORRECT SHOWER TRAY INSTALLATION

WALL

TILE OR WETWALL PANEL

SHOWER TRAY

YES

WALL

TILE OR WETWALL PANEL

SHOWER TRAY

NO

STEP 3 TRAY TO BE LEVELMAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THISSHOWER PANEL / DOOR, AND THAT SILICONE IS APPLIED ON ALL SIDES WHERE THETRAY MEETS THE TILES / WET WALL PANELS.

1950x701x8

1950x39 1950x39 1950x39 1950x39 1950x39Wall post

1950x741x8 1950x841x8 1950x941x8 1950x741x8

LSP1002LSP7602 LSP802 LSP902 LSP802BLK

Measurement Matrix (before assembly) Dimension in mmUnits supplied loose for self assembly

Flat fixed panel glass (including fixed panel profiles if attached)

5

STEP 8 SLIDE WALL PROFILE ON TO THE SIDE PANEL

STEP 9 MARK THE CORRECT DRILL HOLE POSITIONS ON THE WALL

FIRST: COMPLETE STEPS 4-7 IN THE DOOR ASSEMBLY INSTRUCTIONS

6

STEP 10 DRILL AND SCREW THE WALL PROFILE TO THE WALL

STEP 11 PUSH THE MAGNET SEALS AND VERTICAL PANEL SEALS ON TO THE GLASS DOOR AND SIDE PANEL

1

6.0mm

x4

St4x303

x4

2x4

21 3

8

9

15mm4

5

12mm6

7

Movingpanel

Movingpanel

Fixedpanel

Fixedpanel

7

STEP 12 SECURING THE SIDE PANEL, FIXED PANEL AND PROFILE COVER STRIPS

STEP 13 FITTING THE TOP BAR, WALL BRACKET AND GLASS CLAMPS

Take care not to drill into the glass

L=0~20mmL≥5mm/R≥10mm

R

L≤5mm/R≥15mm

1

2

3

50~100mm

1 2

1

2

3

4

5

ST4X30

6.0mm

150mm

150mm

2

St4x12

1

3.0mm

x6

x6

3

x6

8

STEP 14 FITTING THE BOTTOM DRIP STRIP

STEP 15 FITTING THE TOP CAPS AND HANDLE

1

3

4

2

4

9

STEP 16 SILICONE THE OUTSIDE EDGES

24 hours

Allow 24 hours for silicone to dry before use. Silicone on the

outside edge only, NOT THE INSIDE

10

CARE AND MAINTENANCE

COMMITMENT TO QUALITY

1) AFTER CARE INSTRUCTIONS

2) MAINTENANCE

Regularly clean your shower product with warm soapy water

Clean the plastic parts with a cloth and mild detergent. Never

use any abrasive creams, dissolvents, acetone or detergents

and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained

in these instructions. The supplier reserves the right to introduce

technical changes without notice.

It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you

firstly contact a competent plumber. However we understand that

this may not always be the case, so should you experience

any problems please contact our customer services quoting

the following:

Customer help line number: 0344 804 48 48

to prevent lime scale build up. Do not use abrasive cleaning

fluids or materials, or strong chemical cleaners as this will

damage the product surface.

Product name:

Product code: LSP7602 / LSP802 / LSP902 / LSP1002 / LSP802BLK

Side Panel For 8mm Frameless Concealed Hinge door

11

12

INSTALLERS NOTES

13

INSTALLERS NOTES

14

INSTALLERS NOTES

The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.

We suggest you take it to the local landfill site and discard in the designated bins.

Victoria Plum Limited, Bridgehead Business Park Hessle, HU13 0DG

16

EN 14428:2004+A1:2008

DOP No.:J160415002

Shower enclosures with aluminiumprofiles and safety glass

Essentialcharacteristics

Performance Harmonisedtechnical

specificationCleanability

Impactresistance/shatter

properties

Pass

Pass

PassDurability

Clause 4.2 of EN14428:2004+A1:

2008Clause 4.3 of EN14428:2004+A1:

2008Clause 4.4 of EN14428:2004+A1:

2008

V08/07/2020