siempre comprometidos con la calidad!
TRANSCRIPT
Dos generaciones fabricando Sistemas de Protección contra:Sobrecorriente (Fusibles) - Sobrevoltajes (DPS & SIPRAS)
Red compacta (Espaciadores)
Siempre comprometidos con la Calidad!
PBX: (57-1) 432 2950Celular: (57-1) 311 591 4043
[email protected] Calle 17 No. 42A - 69
Bogotá D.C. - Colombia
CONTÁCTENOS
Catalogo de Productos
T&D - TELECOMUNICACIONES - EDIFICACIONES
2020
I. LABORATORIO DE PRUEBAS ACREDITADO POR ONAC LABORATORIO
II. TRANSMISIÓN Y DISTRIBUCIÓNFusibles de Expulsión Primario cabeza �ja y removible para 15 y 38 kV marca LUHFSER (Media Tensión) Fusibles de Mono ElementoFusibles de Doble ElementoDescargadores por Sobretensión (DPS) marca STAVOL (Media Tensión) Porta DPS y Desconectador marca STAVOL con Herrajes en Acero Inoxidable Autenítico 304 (Media Tensión)Cortacircuitos 15kV marca STAVOL (Media Tensión)Seccionador marca STAVOL (Media Tensión)Fusibles para alumbrado Público marca LUHFSER (Baja Tensión) Bases Porta Fusibles Sencillos y Dobles para Luminaria marca LUHFSER (Baja Tensión)Caja Fusible marca LUHFSER (Baja Tensión)Sistemas de Puesta a Tierra para Transmisión y Distribución marca STAVOL en Acero Inoxidable Autenítico 304
III. TELECOMUNICACIONESSistemas de Puesta a Tierra para Telecomunicaciones marca STAVOL en Acero Inoxidable Autenítico 304
IV. CONECTORES PARA SPTConectores para SPT marca STAVOL en Acero Inoxidable Autenítico 304
V. DISPOSITIVOS MECÁNICOS PARA SISTEMAS INTEGRALES DE PROTECCIÓN CONTRA RAYOS (SIPRAS)Conductores marca STAVOL en Acero Inoxidable Autenítico 304Electrodos marca STAVOL en Acero Inoxidable Autenítico 304Puntas Captadoras marca STAVOL en Acero Inoxidable Autenítico 304Conectores para SIPRAS marca STAVOL en Acero Inoxidable Autenítico 304
VI. SISTEMAS DE SUJECIÓNInforme de Ensayo Laboratorio Interfacultades de Ensayos MecánicosFlejes, Hebillas y Abrazaderas marca STAVOL en Acero Inoxidable Autenítico 304
VII. RED COMPACTAEspaciador en Polietileno de alta densidad marca STAVOL (Media Tensión)Brazo Antibalanceo (Media Tensión)Ménsula (Media Tensión)
CALIDAD DE LA ENERGÍA ELÉCTRICACALIDAD DE LA POTENCIA
3
Pg.
7
8
10
11
12
14
15
17
1819
6
9
16
PROTECCIÓN CONTRA SOBRECORRIENTE PROTECCIÓN CONTRA SOBREVOLTAJE RED COMPACTA
CONTENIDO
Para tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
Política de CalidadEl laboratorio de ELÉCTRICOS INTERNACIONAL LTDA., presta servicios de ensayo a productos eléctricos basados en los requerimientos del cliente y en las normas técnicas nacionales e internacionales, de acuerdo con los métodos establecidos y los requisitos de los clientes. Cuenta con personal técnico, competente e imparcial, con formación y entrenamiento, familiarizados con la documentación de la calidad y comprometidos en la implementación de las políticas y los procedimientos en su trabajo.
Es compromiso de la alta dirección las buenas prácticas profesionales, la calidad de los ensayos durante el servicio a sus clientes y el cumplimiento de la norma NTC ISO/IEC 17025 y la mejora continua de sus procesos para alcanzar la e�cacia del sistema de gestión cuyo propósito es garantizar la prestación de un servicio con�able, imparcial, con�-dencial y oportuno, para lograr la satisfacción del cliente y reconocimiento en el mercado.
La vigencia de este certi�cado se puede veri�car en www.onac.org.coCerti�cado de Acreditación 12-LAB-055
ENSAYO
Ensayo Tiempo - Corriente Eléctrica
Fusibles eléctricos(fusibles de expulsión)
media tensión15 kV a 38 kV
1A a 1000A (ac),20ms a 630s
NTC 2132:2006 numerales 4.1.1, 4.2.1, 4.3.1, 4.5.3,4.6.1 y numeral 12. NTC 2133:2002 numeral 4.3 y
tabla 6 y 7. IEEE Std C37.41 - 2016 cor 2017 numeral7.5.1, 7.6.1, 7.7.1, 7.10.1, 7.10.3, y 12. IEEE Std
C37.42 - 2016 numeral 7.2 y tabla 13 y 14.
Ensayo de elevaciónde la temperatura Térmica
Fusibles eléctricos(fusibles de expulsión)
media tensión 15 kV a 38 kV
20 °C a 52 °C /1 A a 200 A (ac)
NTC 2132:2006 numerales 4.1, 4.2, 4.3, 4.5.3,4.6.1 y numeral 11 IEEE Std C37.41 - 2016 cor
2017 numeral 7, 11 y 12.
Fusibles eléctricos(fusibles de expulsión)
media tensión15 kV a 38 kV
“Procedimiento requisitos deintercambiabilidad mecánica
de los fusibles”,CFB P 044, Versión 5 de 2018-02-06
TÉCNICAMÉTODO ELEMENTO A ENSAYAR INTERVALO DE
MEDICION DOCUMENTO NORMATIVO
Veri�cación de los requisitos deintercambiabilidad mecánica de los
hilos fusibles (Medición del diámetrode la cabeza, longitud mínima total,espesor máximo de la sección por
doblar y ensayo de tracción)
Mecánica
Longitud: 1 mm a1000mm Esfuerzo de
tracción: 19,6 N a 177 N(4,4 lbf a 39,8 lbf)
Voltaje: 2 mV a 900 V Corriente eléctrica:
1 A a 1000 A
Fusibles eléctricos (fusiblesmisceláneos tipo casquete
clase CC) baja tensión hasta 600 V
UL 248-1:2011 numeral 8.2UL 248-4:2000 numeral 8.2
Veri�cación del incremento detemperatura y capacidad de conducción
de corriente en fusibles hasta 30 AEléctrica 20 °C a 91 °C /
1 A a 30 A (ac)
Fusibles eléctricos(fusibles NH tipo pala)
baja tensión hasta 500 V
IEC 60269-1:2014 numeral 8.3IEC 60269-2:2016 Figura 101 y 106
Veri�cación del incrementode temperatura y potencia
de disipaciónTérmica 20 °C a 90 °C /
1 A a 125 A (ac)
Fusibles eléctricos(fusibles NH tipo pala)
baja tensión hasta 500 V
IEC 60269-1:2014 numeral 8.4.3.1 y tabla 2IEC 60269-2:2016 Figura 101 y 106
Veri�cación de la corriente convencional de fusión
y no fusiónEléctrica 3 A a 200 A (ac)
1s a 7500s
Fusibles eléctricos (fusibles NHtipo pala) baja tensión hasta 500 V
IEC 60269-1:2014 numeral8.4.3.3.2 y tabla 3Veri�cación de "GATES" Eléctrica 3 A a 1100 A (ac)
20ms a 15s
Bases portafusibles clase CC UL 4248-1:2017 numeral 8.4UL 4248-4:2007 numeral 8.4
Veri�cación del incrementode temperatura Térmica 20 °C a 48 °C /
1 A a 30 A (ac)
Botas Industriales ASTM F2412-18a Numerales 9.1, 9.2, 9.3.2,9.4, 9.5 y 9.6
Ensayos de rigidez dieléctrica afrecuencia industrial Eléctrica Falla / No falla el ensayo
eléctrico
Mangas Aislantes tipo I y II,clase 00, 0, 1, 2, 3 y 4.
ASTM D1051-19 / 9.1, 18.1, 18.2, 18.3, 18.3.1.1, 18.4.1,18.4.2, 18.5.1, 18.5.2
ASTM F496 - 14a 6.4, 7.1.1, 7.1.2, 7.2, 7.6, 7.6.1.1, 7.7.1
Ensayos de rigidez dieléctrica afrecuencia industrial Eléctrica
Soporta / No soporta latensión eléctrica de
ensayo aplicada.
Guantes Dieléctricos tipo I y II,Clase 00, 0, 1, 2, 3 y 4
ASTM D120-14a /11.1, 18.1, 18.2, 18.3, 18.4.1, 18.4.2
ASTM F496-14a /6.4, 7.1.1, 7.1.2, 7.2, 7.5.1, 7.5.2, 7.7.1
Ensayos de rigidez dieléctrica afrecuencia industrial Eléctrica
Soporta / No soporta la tensión eléctrica de
ensayo aplicada.Supera / No supera la
corriente de fugamáxima permitida.
HECHO EN COLOMBIA3
I. LABORATORIO DE PRUEBAS ACREDITADO POR ONAC
ISO/IEC 17025:201712-LAB-055
LABORATORIO DE PRUEBASELÉCTRICAS ACREDITADO POR
ISO/IEC 17025:201712-LAB-055
Tipo VS (1 a 100 AMP) Tipo SR (0.2 a 46 AMP) Adaptador Universal
Normas Técnicas:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Fuse Element: Aleación NTCRelación de Velocidad: 18 a 24
Tubo en �bra vulcanizada
Normas Técnicas:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Hilo Fusible: Aleación NTCRelación de Velocidad: 13 a 21
Tubo en �bra vulcanizada
Normas Técnicas:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Para corta circuitos de doble cola
Fusi
bles
de
Dob
le E
lem
ento
Tipo T (1 a 200 AMP) Tipo H (1 a 100 AMP) Tipo K (1 a 200 AMP)
Normas Técnicas:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Hilo Fusible: Estaño o aleación de PlataRelación de Velocidad: 7 a10Tubo en �bra vulcanizada
Normas Técnicas:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Hilo Fusible: Aleación de PlataRelación de Velocidad: 7,1 / 8,8
Tubo en �bra vulcanizada
Normas Técnicas:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Hilo Fusible: Estaño o aleación de PlataRelación de Velocidad: 10 a 13
Tubo en �bra vulcanizada
Normas Técnicas:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Hilo Fusible: CobreRelación de Velocidad: 4 a 6Tubo en �bra vulcanizada
Tipo NS (1 a 100 AMP)
Fusi
bles
de
mon
o el
emen
to
Tubo Auxiliar
Fabricados en �bra vulcanizada de su�ciente espesor y con las especi�caciones técnicasapropiadas que garantizan el cumplimiento de la norma de �amabilidad ASTM D-635
Nuestros tubos:NO queman cañuelas, NO generan incendios, NO queman contactos eléctricos!
II. TRANSMISIÓN Y DISTRIBUCIÓN
Fusibles de Expulsión Primario cabeza �ja y removible para 15 y 38 kV marca LUHFSER (Media Tensión)
HECHO EN COLOMBIA 6
Para tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
DPS 36 kVDPS 9, 12 y 15 kV DPS 21 y 24 kV
PORTA DPS Max. 15 kV PORTA DPS Max. 36 kV DESCONECTADOR
HEAVY DUTY 100 kANivel de Protección en Tensión: 41.5 kVp
Altura: 143 mm12 kV10.2 kV10 kA
(U ):MCOV:(U ):c
20 kA50 - 60 Hz95 - 90 kV
(I ):(F ):BIL:
c
HEAVY DUTY 100 kANivel de Protección en Tensión: 66 kVp
Altura: 286 mm21 kV17 kV10 kA
(U ):MCOV:(U ):c
20 kA50 - 60 Hz180 kV
(I ):(F ):BIL:
c
HEAVY DUTY 100 kANivel de Protección en Tensión: 116 kVp
Altura: 426 mm36 kV29 kV10 kA
(U ):MCOV:(U ):c
20 kA50 - 60 Hz270 kV
(I ):(F ):BIL:
c
NORM
AS TÉ
CNIC
AS: I
EEE C
62.1
1: 20
12 / I
EC 60
099 -
4: 20
14NO
RMAS
TÉCN
ICAS
: IEE
E C62
.11:
2012
/ IEC
6009
9 - 4:
2014
Tensión Nominal de Operación: 15 kVPosición de Instalación: Vertical
Tipo: ReemplazablePeso: 5.66 KgBIL: 110 kV
Tensión Nominal de Operación: 36 kVPosición de Instalación: Vertical
Tipo: ReemplazablePeso: 8.66 KgBIL: 110 kV
Fuerza Mecánica
Carga de Rotura: 3000NResistencia de Flexión: 60NmResistencia de Torsión: 27Nm
Descargadores por Sobretensión (DPS) marca (Media Tensión)
Porta DPS y Desconectador marca con herrajes en Acero Inoxidable Austenítico 304 (Media Tensión)
Cortacircuitos 15kV marca (Media Tensión)
HECHO EN COLOMBIA7
ESPECIAL PARA ZONAS COSTERAS O DE ALTA CONTAMINACIÓN
Herrajes en Acero Inoxidable Austenítico 304
Normas técnicas: IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Tensión de operación: 15 kV
Corriente continua de operación: 100 A
Capacidad de interrupción: Simétrico: 7.1 kA - Asimétrico 10 kA
BIL: 110 kV
Distancia de fuga: 800 mm
Herrajes de sujeción: Diseñados bajo el cumplimiento de la norma IEEE C37.42
Ganchos para apertura bajo carga: Compatible con herramienta LoadBuster
Peso: Aproximado 5.5 Kg
Aisladores en siliconas HTV WACKER
PRODUCTO
PATENTADO
Seccionador para15 kV y 24 kV
Seccionador marca (Media Tensión)
Seccionador 15 kVEspeci�caciones Seccionador 24 kV
Normas técnicas:
Tensión de referencia:
Corriente Nominal (Ic):
BIL:
Corriente corta duración:
Distancia de fuga:
Frecuencia de operación:
Material de los aisladores:
Peso:
Forma de montaje:
Tipo de maniobra:
Material de herrajes:
15 kV
110 kV
24 kV
150 kV
IEC 62271-102, IEC 60694 (NTC 2157 Y 3274)
25 kA asimétrico por 1 segundo
840 mm
60 Hz
Silicona HTV WACKER
Aproximado 6.6 Kg
Horizontal / Vertical
Pértiga
Acero Inoxidable Autenítico 304
630 A
Tensión: 1000 V(I ): 70 &100 AMPS
(C ): 10 kAI
Normas Técnicas: UL 4248 - 1: 2007 / UL 4248 - 4: 2007BASE: Moldeada en PolicarbonatoBORNES: Con tornillos de acero galvanizado y clips de contácto en aleación de cobre niqueladoRANGO: 30 Amperios - 600 VoltiosPARA CONDUCTOR DE: 1.5 - 6 mm²
Tensión: 600 V(I ): 5 &10 AMPS
(C ): 10 kAI
Fusibles para Alumbrado Público marca LUHFSER (Baja tensión)
Bases Porta Fusibles Sencillos y Dobles para Luminaria marca LUHFSER (Baja tensión)
Tensión: 250 V(I ): 5 & 10 AMPS
(C ): 3 kAI
Normas Técnicas:UL 248 - 1: 2011 / UL 248 - 4: 2000
Normas Técnicas:UL 248 - 1: 2011 / UL 248 - 4: 2000
Normas Técnicas:UL 248 - 8: 2011
Fusibles CBO (250V)para Luminaria
Fusible Sumergible paraTransformador Tipo Pedestal
Fusibles QSQ (600V)para Luminaria
HECHO EN COLOMBIA 8
Caja Fusible hasta 200A marca LUHFSER (Baja Tensión)
HECHO EN COLOMBIA9
PATENTE EN
TR A MITE
11,4 kV 13,2 kV
15 0,75 0,65 0,4 40 Exs30 1,52 1,31 1,0 80 Exs45 2,28 1,97 1,4 125 Exs75 3,80 3,28 2,1 200 Exs
5 0,4 40 Exs10 0,6 80 Exs15 1,0 125 Exs
0,37 410,76 831,13 125
KVA
PRIMARIO SECUNDARIOCorriente Nominal ( A).
Tipo de Fusible DUAL Recomendado
Corriente Nominal ( A). Fusible de Expulsion Recomendado para usar con
el interruptor de desconexion
13,2 kV 120 V
4283
125208
TRANSFORMADORES MONOFASICOS
TRANSFORMADORES TRIFASICOS
KVA
PRIMARIO SECUNDARIOCorriente Nominal ( A).
Tipo de Fusible DUAL Recomendado
Corriente Nominal ( A). Fusible de Expulsion Recomendado para usar con
el interruptor de desconexion
208/120 V
Kit RGDAT con cubiertaextruida HDPE
Medidores y ArmariosAPLICACIONES
Kit SPT con cubiertaextruida PVC
Alumbrado Público Poste MetálicoAPLICACIONES
HECHO EN COLOMBIA 10
KIT SPT
OleoductosTransformador de Distribución
Neutro PrimarioNeutro Secundario
Cable Guarda BayonetaSeccionador Bajo Carga Telecontrolada (SBCT)
Contrapeso linealDescargador por Sobretensión (DPS)
APLICACIONES
Norm
as Té
cnica
s: AS
TM A4
80 / A
480M
- 16a
/ AST
M A6
66 - 1
5 - UL
467:
2013
/ IEE
E 80
Norm
as Té
cnica
s: AS
TM A4
80 / A
480M
- 16a
/ AST
M A6
66 - 1
5 - UL
467:
2013
/ IEE
E 80
Norm
as Té
cnica
s: AS
TM A4
80 / A
480M
- 16a
/ AST
M A6
66 - 1
5 - UL
467:
2013
/ IEE
E 80
II. TRANSMISIÓN Y DISTRIBUCIÓNPara tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
(Kits) Sistemas de Puesta a Tierra marca en Acero Inoxidable Austenítico 304Todos los SPT van en desnudo o con cubierta extruida en PVC y HDPE. PATENTE DE MODELO DE UTILIDAD No. 800
III. TELECOMUNICACIONESPara tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
8
(Kits) Sistemas de Puesta a Tierra marca en Acero Inoxidable Austenítico 304Todos los SPT van en desnudo o con cubierta extruida en PVC y HDPE. PATENTE DE MODELO DE UTILIDAD No. 800
Kit SPT con cubierta extruida HDPEHibrido de Fibra Coaxial (HFC)
HECHO EN COLOMBIA11
KIT SPT
APLICACIONES
APLICACIONES
Norm
as Té
cnica
s: AS
TM A4
80 / A
480M
- 16a
/ AST
M A6
66 - 1
5 - UL
467:
2013
/ IEE
E 80
Norm
as Té
cnica
s: AS
TM A4
80 / A
480M
- 16a
/ AST
M A6
66 - 1
5 - UL
467:
2013
/ IEE
E 80
Torres de TelecomunicacionesArmario Telefónico
CámaraEquipos Aéreos y Ampli�cadores
Caja Fibra Óptica
12
Conector Bypass Conector Tipo J
Conector Tipo U 10mmConector Tipo U 5/8
Conector Tipo C
Conector Tipo Cuña
Conectores para SPT marca en Acero Inoxidable Austenítico 304
IV. CONECTORES PARA SPTPara tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
Conector Tipo Pala(Sencilla – Doble) Conector Tipo TConector Múltiple
de Placas Paralelas
HECHO EN COLOMBIA 12
DISEÑO
INDUSTRIAL
DISEÑO
INDUSTRIAL
PRODUCTO
PATENTADO
PRODUCTO
PATENTADO
PRODUCTO
PATENTADO
Conector Tipo Cruz Conector Tipo Mpara Cable Mensajero
Conector CableElectrodo Tipo Varilla
Conector paraCables Cilíndricos
Conector PlacaParalela Tipo Bisagra
Conector paraElectrodo Tipo Placa
Sujetador Guía Sistema de Ensamblaje Base para PuntaCaptadora Plana
HECHO EN COLOMBIA13
Conectores para SPT marca en Acero Inoxidable Austenítico 304
DISEÑO
INDUSTRIAL
PRODUCTO
PATENTADO
PRODUCTO
PATENTADO
HECHO EN COLOMBIA 14
Electrodo Placa Acero Inoxidable200 mm x 100 mm x 6.35 mm
Electrodo Varilla Acero Inoxidable* 10 mm (1.50 m a 2.40 m)
* 1/2 (1.50 m a 2.40 m)* 5/8 (1.50 m a 2.40 m)
Electrodo Tubo Acero Inoxidable
Electrodos marca en Acero Inoxidable Austenítico 304
V. DISPOSITIVOS MECÁNICOS PARA SISTEMASINTEGRALES DE PROTECCIÓN CONTRA RAYOS (SIPRAS)
Para tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
Conductores marca en Acero Inoxidable Austenítico 304
Conductor 12.70 mm x 1.20 mm
Conductor 22 mm x 1.20 mm
Conductor 22 mm x 1.50 mm
Conductor 25 mm x 2 mm
Conductor 30 mm x 3 mm
HECHO EN COLOMBIA15
Puntas Captadoras marca en Acero Inoxidable Austenítico 304
Conectores para SIPRAS marca en Acero Inoxidable Austenítico 304
Punta Captadora Plana* 10 mm (60 cm a 1.20 m
* 5/8 (60 cm a 1.20 m)
Punta Captadora Acero Inoxidable* 10 mm (60 cm a 1.20 m
* 5/8 (60 cm a 1.20 m)
Punta Captadora FranklinAcero Inoxidable
Soporte para Cumbrera
Conector Múltiplepara Conductores
Barrajes x 100mm x 1/4de (200-400-500-600) Base para Punta Captadora
Soporte paraConductor BajanteAislador para Intemperie
PRODUCTO
PATENTADO
HECHO EN COLOMBIA 16
Flejes(3/8), (1/2), (5/8) y (3/4)
Normas Técnicas:ASTM A480 / A480M - 16a / ASTM A666 - 15
Acero Inoxidable Austenítico304 y 316
Hebillas(3/8), (1/2), (5/8) y (3/4)
Normas Técnicas:ASTM A480 / A480M - 16a / ASTM A666 - 15
Acero Inoxidable Austenítico 304
Normas Técnicas:ASTM A480 / A480M - 16a / ASTM A666 - 15
Acero Inoxidable Austenítico 304
Abrazaderas(3/8), (1/2), (5/8) y (3/4)
Flejes, Hebillas y Abrazaderas marca en Acero inoxidable Autenítico 304
VI. SISTEMAS DE SUJECIÓNPara tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
LABORATORIO INTERFACULTADES DE ENSAYOS MECÁNICOSINFORME DE ENSAYO
¿Está usted utilizando el Acero correcto en las instalaciones que realiza?Eléctricos Internacional Ltda. garantiza a sus clientes que nuestros productos son fabricados en
ACERO INOXIDABLE AUSTENÍTICO 304tal y como lo exigen y especi�can las normas.
En la norma NTC 3496:2009 se hace mención en la “Tabla 7”, sobre el mínimo valor de fuerza máxima que debe soportar el montaje, siendo para la conta de “5/8 de pulgada” (15,88 mm) de 450 kgf.
En las siguientes imágenes se ilustra la instalación y comportamiento final de una de las muestras ensayadas.
HECHO EN COLOMBIA17
SpacerNormas Técnicas: ASTM D2303 - 13 / ASTM D150 - 11 / ASTM G154 - 12aTensión de servicio: 8,7/15 kVResistencia al tracking e intemperieAltísima resistencia al impactoMaterial: Polietileno alta densidadColor: GrisDiámetro de cables: 9 a 32 mmLínea de fuga: 280 mmPeso: 450 grs.Diámetro de rosca: 25 - 35 mmBaja radiointerferencia.
(Media Tensión)Espaciador en Polietileno de alta densidad marca
Brazo Antibalanceo (Media Tensión)
Ménsula (Media Tensión)
VII. RED COMPACTAPara tablas comparativas ver boletines técnicos en nuestra página web www.electricosinter.com
25 ±2
A ±5
M 16 x 2
74 ±5
41 ±2
15 ±2
19,5 ±2 80
B
75 97
A 250
PERNO 16 mm
17.5 x 25.4
C
21 21
CaracterísticasTiene como principio disminuir el balanceo de la red eléctrica y mantener la distancia del espaciador y el cable en relación al poste cuando la red esté en ángulos pequeños.
Producido en polietileno gris de alta densidad. Utilizado en tensiones de 15 a 35 KV.
Resistencia a rayos UV y al impacto eléctrico.
CaracterísticasHerraje usado para la sustentación de cable mensajero de las líneas compactas de 15 KV.
Fabricado en acero estructural. Está compuesto por un cuerpo y un conjunto prensa cable. Todos los elementos son galvanizados en caliente.
NOTA: GALVANIZADO POR INMERSION EN CALIENTE NORMA NTC 2076 EL CONECTORHECHO EN FUNDICION NODULAR
La calidad del servicio signi�ca tener el servicioDÓNDE y CUÁNDO sea necesario.
CALIDAD DE LA ENERGÍA ELÉCTRICA
FUSIBLES DEEXPULSIÓN
DESCARGADOR POR SOBRETENSIÓN
SEGURIDADNO FUNDEN CUANDO
NO DEBEN FUNDIR
La seguridad es el aspecto de la con�abilidad que expresa el grado de
certeza de que el fusible no operará incorrectamente bajo condiciones normales.
Se mide como la probabilidad de que el sistema de protecciones no presente
actuaciones de falla o que actúen otras protecciones diferentes a las que debieron
actuar.
Innovamos el concepto de aterrizamientos en Colombia, mediante el desarrollode Kits de Puesta a Tierra en Acero Inoxidable Austenítico 304.
Propiedad Intelectual de Eléctricos Internacional LTDA.
El 80% de las fallas eléctricas sedeben a puestas a tierra inadecuadas.
CALIDAD DE LA POTENCIA
KIT SPT EN ACERO INOXIDABLE
FLEJES YHEBILLAS
FIABILIDADFUNDEN CUANDODEBEN FUNDIR
La �abilidad es el aspecto de la con�abilidad que expresa el grado de certeza de que el sistema de protección operará correctamente ante la presencia de una condición anormal o falla, tomando las acciones necesarias ante esta situación.
Se mide como la probabilidad de que el sistema actúe efectivamente en presencia de una falla.
Always committed to quality!
Two generations manufacturing Protection Systems against:Overcurrent (Fuses) - Overvoltage (SA & SLP)Ecological Network (Spacers)
Product Catalog
T&D - TELECOMMUNICATIONS - BUILDINGS
I. TESTING LABORATORY ACCREDITED BY ONAC LABORATORY
II. TRANSMISSION & DISTRIBUTIONLUHFSER Expulsion Fuses �xed and removable head for 15 and 38 kV (Medium Voltage) Mono Fuse ElementDouble Fuse ElementSTAVOL Surge Arresters Distribution Class (Medium Voltage) STAVOL Drop Out Surge Arrester (DOSA) and Disconnector (Medium Voltage)STAVOL Coastal Cutout 15kV (Medium Voltage)STAVOL Hookstick Switch 15 kV and 24 kV (Medium Voltage)LUHFSER Fuses for Street Lights (Low Voltage) LUHFSER Fuse Holders Single and Double for Street Lights (Low Voltage)LUHFSER Secondary Fuse Box up to 200 A (Low Voltage)STAVOL (Kits) Grounding Systems in Austenitic Stainless Steel type 304
III. TELECOMMUNICATIONSSTAVOL (Kits) Grounding Systems in Austenitic Stainless Steel type 304
IV. GROUNDING SYSTEMS CONNECTORSConnectors for GKS in Austenitic Stainless Steel type 304
V. STRUCTURAL LIGHTNING PROTECTIONConductors in Austenitic Stainless Steel type 304Electrodes in Austenitic Stainless Steel type 304Franklin Rods in austenitic stainless steel type 304Structural Lighning Protection Connectors in austenitic stainless steel type 304
VI. FASTENING SYSTEMSTest ReportStraps, Buckles and Premade Clamps in Austenitic Stainless Steel type 304
VII. OVERHEAD AERIAL COMPONENTSSTAVOL HDPE Spacer (Medium Voltage)Anti-Sway Bracket (Medium Voltage)Tangent Bracket (Medium Voltage)
34
Pg.
6
7
9
10
11
13
14
16
5
8
15
CONTENT
OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OVERHEAD AERIAL COMPONENTS
Quality PolicyELECTRICOS INTERNACIONAL LTDA., Laboratory provides testing services for electrical products based on customer requirements and national and international technical standards, according to established methods and customer requirements. It has technical personnel, competent and impartial, with education and training, familiar with the quality documentation and committed to policies and procedures related to their work ethics.
Senior management commitment is, for the good professional practices, the quality of tests during the service to its customers and our compliance with the standard NTC ISO / IEC 17025. The main purpose of the quality manage-ment system is to ensure reliable service, just in time delivery, con�dential, impartial and timely reports, seeking continuous improvement of their processes to achieve maximum customer satisfaction and market recognition.
TEST
Time - Current Test ELECTRIC
Electric fuses(expulsion fuses)medium voltage
15 kV to 38 kV
1A to 1000A (ac),20ms to 630s
NTC 2132: 2006 numerals 4.1.1, 4.2.1, 4.3.1, 4.5.3,4.6.1 and numeral 12. NTC 2133: 2002 numeral 4.3 andTable 6 and 7. IEEE Std C37.41 - 2016 cor 2017 numeral
7.5.1, 7.6.1, 7.7.1, 7.10.1, 7.10.3, and 12. IEEE StdC37.42 - 2016 numeral 7.2 and table 13 and 14.
Elevation testof temperature THERMAL
Electric fuses(expulsion fuses)
medium voltage 15 kV to 38 kV
20 °C to 52 °C /1 A to 200 A (ac)
NTC 2132: 2006 numerals 4.1, 4.2, 4.3, 4.5.3,4.6.1 and numeral 11 IEEE Std C37.41 - 2016 cor
2017 numeral 7, 11 and 12.
Electric fuses(expulsion fuses)medium voltage
15 kV to 38 kV
“Procedure requirements ofmechanical interchangeability
of the fuses ”,CFB P 044, Versión 5 de 2018-02-06
TECHNIQUEMETHOD ELEMENT TESTED INTERVAL OF
MEASUREMENT REGULATORY DOCUMENT
Veri�cation of the requirements ofmechanical interchangeability of
fuse wires (Diameter measurementof the head, minimum total length,
maximum section thickness pertensile test)
MECHANICAL
Length: 1mm to1000mm E�ort
Traction: 19.6 N to 177 N(4.4 lbf to 39.8 lbf)
Voltage: 2mV to 900VElectric current:
1 A to 1000 A
Electric fuses (fusescap type miscellaneous
class DC) low voltage up to 600 V
UL 248-1:2011 numeral 8.2UL 248-4:2000 numeral 8.2
Veri�cation of the increase in oftemperature and driving capacity
current in fuses up to 30 AELECTRIC 20 °C to 91 °C /
1 A to 30 A (ac)
Electric fuses(blade type NH fuses)
low voltage up to 500 V
IEC 60269-1:2014 numeral 8.3IEC 60269-2:2016 Figure 101 y 106
Veri�cation of the increaseof temperature and power
dissipationTHERMAL 20 °C to 90 °C /
1 A to 125 A (ac)
Electric fuses(blade type NH fuses)
low voltage up to 500 V
IEC 60269-1:2014 numeral 8.4.3.1 y tabla 2IEC 60269-2:2016 Figure 101 y 106
Check currentconventional fusion
and not fusionELECTRIC 3 A to 200 A (ac)
1s to 7500s
Electric fuses (NH fusesshovel type) low voltage up to 500 V
IEC 60269-1:2014 numeral8.4.3.3.2 and table 3Veri�cation of "GATES" ELECTRIC 3 A to 1100 A (ac)
20ms to 15s
Class CC fuse holders UL 4248-1:2017 numeral 8.4UL 4248-4:2007 numeral 8.4
Veri�cation of the increaseOf temperature ELECTRIC 20 °C to 48 °C /
1 A to 30 A (ac)
Industrial Boots ASTM F2412-18a Numerals 9.1, 9.2, 9.3.2,9.4, 9.5 y 9.6
Dielectric strength tests atindustrial frequency ELECTRIC Fail / Fail the test
electric
Insulating sleeves type I and II,class 00, 0, 1, 2, 3 and 4
ASTM D1051-19 / 9.1, 18.1, 18.2, 18.3, 18.3.1.1, 18.4.1,18.4.2, 18.5.1, 18.5.2
ASTM F496 - 14a 6.4, 7.1.1, 7.1.2, 7.2, 7.6, 7.6.1.1, 7.7.1
Dielectric strength tests atindustrial frequency ELECTRIC
Supports / Does not supportelectrical voltage of
applied test.
Type I and II Dielectric Gloves,Class 00, 0, 1, 2, 3 and 4
ASTM D120-14a /11.1, 18.1, 18.2, 18.3, 18.4.1, 18.4.2
ASTM F496-14a /6.4, 7.1.1, 7.1.2, 7.2, 7.5.1, 7.5.2, 7.7.1
Dielectric strength tests atindustrial frequency ELECTRIC
Supports / Does not supportelectrical voltage of
applied test.Exceeds / does not exceed
leakage currentmaximum allowed.
I. TESTING LABORATORY ACCREDITED BY ONAC
ISO/IEC 17025:201712-LAB-055
For comparative tables see technical bulletins on our website www.electricosinter.com
According to NTC International Standard ISO / IEC 17025The validity of this certi�cate can be veri�ed at www.onac.org.co
Accreditation Certi�cate 12-LAB-055
MADE IN COLOMBIA 3
TESTING LABORATORYACCREDITED BY ONAC
ISO/IEC 17025:201712-LAB-055
Type VS (1 to 100 AMP) Type SR (0.2 to 46 AMP) Universal Adapter
Type T (1 to 200 AMP) Type H (1 to 100 AMP) Type K (1 to 200 AMP)
Type NS (1 to 100 AMP)
Made of vulcanized �ber of su�cient thickness and with the technical speci�cationsappropriate that guarantee compliance with the �ammability standard ASTM D-635
Our tubes:DO NOT damage fuse holders, DO NOT generate fires, DO NOT burn electrical contacts!
II. TRANSMISSION & DISTRIBUTION
MADE IN COLOMBIA 5
For comparative tables see technical bulletins on our website www.electricosinter.com
LUHFSER Expulsion Fuses �xed and removable head for 15 and 38 kV (Medium Voltage)
Technical Standards:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Fuse Element Tin or Silver alloySpeed Ratio: 7 to 10
Vulcanized �ber tubes
Technical Standards:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Fuse Element : Tin or Silver alloySpeed Ratio: 10 to 13Vulcanized �ber tubes
Technical Standards:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Fuse Element : CopperSpeed Ratio: 4 to 6
Vulcanized �ber tubes
Mon
o Fu
se E
lem
ent
Technical Standards:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Fuse Element : Silver alloySpeed Ratio: 7,1 / 8,8
Vulcanized �ber tubes
Auxiliary Tube
Dou
ble
Fuse
Ele
men
t
Technical Standards:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Fuse Element: NTC AlloySpeed Ratio: 18 to 24Vulcanized �ber tubes
Technical Standards:IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Fuse Element: NTC AlloyTechnical Standards:
IEEE STD C37.41:2016 / IEEE STD C37.42:2016For double tail Cutouts
Arrester 36 kVArrester 9, 12 y 15 kV Arrester 21 y 24 kV
DOSA Max. 15 kV DOSA Max. 36 kV DISCONNECTOR
HEAVY DUTY 100 kAVoltage Protection Level: 41.5 kVp
Height: 143 mm12 kV10.2 kV10 kA
(U ):MCOV:(U ):c
20 kA50 - 60 Hz95 - 90 kV
(I ):(F ):BIL:
c
HEAVY DUTY 100 kAVoltage Protection Level: 66 kVp
Height: 286 mm21 kV17 kV10 kA
(U ):MCOV:(U ):c
20 kA50 - 60 Hz180 kV
(I ):(F ):BIL:
c
HEAVY DUTY 100 kAVoltage Protection Level: 116 kVp
Height: 426 mm36 kV29 kV10 kA
(U ):MCOV:(U ):c
20 kA50 - 60 Hz270 kV
(I ):(F ):BIL:
c
COASTAL AREAS OR HIGH POLLUTIONTechnical Standards: IEEE STD C37.41:2016 / IEEE STD C37.42:2016
Austenitic Stainless Steel Fittings type 304Operating voltage: 15 kVContinuos operation: 100 AInterrupting capability: Symmetrical: 7.1 kA - Asymmetric 10 kABIL: 110 kVCreepage distance: 800 mmFastening hardware: Designed under the compliance with the standard IEEE C37.42Hooks opening under load: Compatible with LoadBuster toolWeight: Approximate 5.5 KgInsulators made with silicone HTV WACKER
Nominal Operating Voltage: 15 kVInstallation Position: Vertical
Type: ReplaceableWeight: 5.66 Kg
BIL: 110 kV
Nominal Operating Voltage: 36 kVInstallation Position: Vertical
Type: ReplaceableWeight: 8.66 Kg
BIL: 110 kV
Mechanical Force
Breaking Load: 3000NFlexural Strength: 60Nm
Torsion Resistance: 27Nm
MADE IN COLOMBIA6
PATENTED
PRO DUCT
Surge Arresters Distribution Class (Medium Voltage)TE
CHNI
CAL S
TAND
ARDS
: IEE
E C62
.11:
2012
/ IEC
6009
9 - 4:
2014
Drop Out Surge Arresters (DOSA) and Disconnector (Medium Voltage)
TECH
NICA
L STA
NDAR
DS: I
EEE C
62.1
1: 20
12 / I
EC 60
099 -
4: 20
14
Coastal Cutout 15kV (Medium Voltage)
Switch 15 kVEspeci�cations Switch 24 kV
Hookstick Switch (Medium Voltage)
Hookstick Switch15 kV and 24 kV
Technical Standards:
Reference voltage:
Current Rating (Ic):
BIL:
Current short duration:
Creepage distance:
Operating Frequency:
Material insulators:
Weight:
Mounting form:
Installation Type:
Material �ttings:
15 kV
110 kV
24 kV
150 kV
25 kA Asymmetric for 1 second
840 mm
60 Hz
Silicone HTV WACKER
Approximate 6.6 Kg
Horizontal / Vertical
Pole
304 Austenitic Stainless Steel
630 A
IEC 62271 - 102: 2001 / IEC 62271 - 1: 2007
LUHFSER Fuses for Street Lights (Low Voltage)
CBO Fuses for Street Lights(250V)
Submersible Fuses forPad-mounted transformer
QSQ Fuses for Street Lights(600V)
Voltage: 250 V(I ): 5 & 10 AMPS
(C ): 3 kAI
Tecnical Standards:UL 248 - 1: 2011 / UL 248 - 4: 2000
Voltage: 600 V(I ): 5 &10 AMPS
(C ): 10 kAI
Tecnical Standards:UL 248 - 1: 2011 / UL 248 - 4: 2000
Voltage: 1000 V(I ): 70 &100 AMPS
(C ): 10 kAI
Tecnical Standards:UL 248 - 8: 2011
LUHFSER Fuse Holders Single and Double for Street Lights (Low Voltage)
TECHNICAL STANDARDS: HOLDER: MOLDED POLYCARBONATEHARDWARE: GALVANIZED AND COPPER NICKEL ALLOYRATING: FOR CONDUCTORS:
MADE IN COLOMBIA 7
LUHFSER Secondary Fuse Box up to 200 A (Low Voltage)
MADE IN COLOMBIA8
PATENT
PEN DIN G
,4 kV , kV
4 Exs Exs
4 Exs Exs
4 Exs Exs Exs
4, kV
THREE PHASE TRANSFORMERS
KVAPRIMARY SECONDARY
Nominal Cu ent ( A) Fuse Type DUAL Ref ce
Nominal Cu ent ( A) Recommended Expulsion Fuse To Be Used With V
SINGLE PHASE TRANSFORMERS
SECONDARYNominal Cu ent ( A) Recommended Expulsion
Fuse To Be Used With D opout Switch
V
Nominal Cu ent ( A)Fuse Type DUAL
Ref ceKVA
PRIMARY
4
Kit RGDAT with extrudedHDPE cover
Electric Meters Kit & CabinetsAPPLICATIONS
Kit With extruded PVC cover
Public Lighting Kit Metal PoleAPPLICATIONS
KIT
Oil PipelinesDistribution Transformer
Neutral PrimaryNeutral Secondary
Overhead Grounding CableUnder Load telecontrolled
Linear CounterweightSurge Arrester (DOSA)
APPLICATIONS
II. TRANSMISSION & DISTRIBUTIONFor comparative tables see technical bulletins on our website www.electricosinter.com
Tech
nica
l Sta
ndar
ds: A
STM
A480
/ A48
0M - 1
6a / A
STM
A666
- 15
UL 46
7: 20
13 / I
EEE 8
0Te
chni
cal S
tand
ards
: AST
M A4
80 / A
480M
- 16a
/ AST
M A6
66 - 1
5 UL
467:
2013
/ IEE
E 80
Tech
nica
l Sta
ndar
ds: A
STM
A480
/ A48
0M - 1
6a / A
STM
A666
- 15
UL 46
7: 20
13 / I
EEE 8
0
MADE IN COLOMBIA 9
(Kits) Grounding Systems in austenitic stainless steel type 304.All GKS go bare or covered with extruded PVC or HDPE. UTILITY MODEL PATENTS No. 800
III. TELECOMMUNICATIONS
8
Kit with extrude HDPE cover
APPLICATIONS
APPLICATIONS
Telephone Underground Split Box KitCell Phone Operator Tower
Overhead Equipment & Ampli�ers KitTelecommunications towers kit
Fiber Optic Box
(Kits) Grounding Systems in austenitic stainless steel type 304.All GKS go bare or covered with extruded PVC or HDPE. UTILITY MODEL PATENTS No. 800
For comparative tables see technical bulletins on our website www.electricosinter.com
Tech
nica
l Sta
ndar
ds: A
STM
A480
/ A48
0M - 1
6a / A
STM
A666
- 15
UL 46
7: 20
13 / I
EEE 8
0Te
chni
cal S
tand
ards
: AST
M A4
80 / A
480M
- 16a
/ AST
M A6
66 - 1
5 UL
467:
2013
/ IEE
E 80
KIT
MADE IN COLOMBIA10
12
Bypass Type Type J
Type U 10mmType U 5/8
Type C
Wedge Connector
IV. GROUNDING SYSTEMS CONNECTORS
Type T
INDUSTRIAL
DESIGN
For comparative tables see technical bulletins on our website www.electricosinter.com
Flat ConductorClamping
Cable and terminal(Single - Double)
Connectors for GKS in Austenitic Stainless Steel type 304
MADE IN COLOMBIA 11
INDUSTRIAL
DESIGN
PATENTED
PRO DUCT
PATENTED
PRO DUCT
PATENTED
PRO DUCT
Type Crossroad Connector Type M ConnectorMessenger Wire Type Rod / Cable Connector
Cylindrical CablesClamping Type Swivel Connector Connector
Type electrode plate
Guide Clamp Assembly Connector Lightning Flat FranklinBase
Connectors for GKS in Austenitic Stainless Steel type304
INDUSTRIAL
DESIGN
PATENTED
PRO DUCT
PATENTED
PRO DUCT
MADE IN COLOMBIA12
Electrode Stainless Steel Plate200 mm x 100 mm x 6.35 mm
Stainless steel electrode rod* 10 mm (1.50 m a 2.40 m)
* 1/2 (1.50 m a 2.40 m)* 5/8 (1.50 m a 2.40 m)
V. STRUCTURAL LIGHTNING PROTECTION
Conductor 12.70 mm x 1.20 mm
Conductor 22 mm x 1.20 mm
Conductor 22 mm x 1.50 mm
Conductor 25 mm x 2 mm
Conductor 30 mm x 3 mm
Conductors in Austenitic Stainless Steel type 304
For comparative tables see technical bulletins on our website www.electricosinter.com
Electrodes in Austenitic Stainless Steel type 304
Stainless Steel Electrode Tube
MADE IN COLOMBIA 13
Franklin Flat Base* 10 mm (60 cm a 1.20 m
* 5/8 (60 cm a 1.20 m)
Franklin Hybrid Base* 10 mm (60 cm a 1.20 m
* 5/8 (60 cm a 1.20 m)
Franklin RodStainless Steel
Franklin Rods in austenitic stainless steel type 304
Structural Lighning Protection Connectors in austenitic stainless steel type 304
Roof SupportFlat Downspout
Conductor Insulator Downspout Support
Multiple FlatConductors
Bus Bar100mm x 1/4
of (200 - 400 - 500 - 600)Lightning Rod Base
PATENTED
PRO DUCT
MADE IN COLOMBIA14
Straps(3/8), (1/2), (5/8) y (3/4)
Buckles(3/8), (1/2), (5/8) y (3/4)
Ready to use clamps(3/8), (1/2), (5/8) y (3/4)
For comparative tables see technical bulletins on our website www.electricosinter.comVI. FASTENING SYSTEMS
LABORATORY INTERFACULTIES OF MECHANICAL TESTSTEST REPORT
Are you using the correct Stainless Steel in your installations?Electricos Internacional Ltda. Guarantees its customers that our products are manufactured in
AUSTENITIC STAINLESS STEEL TYPE 304as required and speci�ed by the regulations.
At the NTC 3496: 2009 standard, mention is made in “Table 7” about the minimum value of maximum force that the assembly must withstand, being for the width of “5/8 inch” (15.88 mm) of 450 kgf.
The following images illustrate the installation and final behavior of one of the samples tested.
Straps, Buckles and Premade Clamps in Austenitic Stainless Steel type 304
Technical Standards:ASTM A480 / A480M - 16a / ASTM A666 - 15
Austenitic Stainless Steel304 y 316
Technical Standards:ASTM A480 / A480M - 16a / ASTM A666 - 15
Austenitic Stainless Steel304
Technical Standards:ASTM A480 / A480M - 16a / ASTM A666 - 15
Austenitic Stainless Steel304
MADE IN COLOMBIA 15
Spacer
Anti-Sway Bracket (Medium Voltage)
Tangent Bracket (Medium Voltage)
VII. OVERHEAD AERIAL COMPONENTS
25 ±2
A ±5
M 16 x 2
74 ±5
41 ±2
15 ±2
19,5 ±2 80
B
75 97
A 250
PERNO 16 mm
17.5 x 25.4
C
21 21
CharacteristicsIts principle is to decrease the swing of the electrical network and maintain the distance of the spacer and the cable in relation to the pole when the network is at small angles.
Made of high-density gray polyethylene. Used in voltages from 15 to 35 KV.
Resistance to UV rays and electrical tracking.
CharacteristicsHardware used to support the messenger cable for the aerial 15 KV lines.
Made of structural steel. It is made up of a body and a cable crimp assembly. All elements are hot dip galvanized.
NOTE: GALVANIZED BY HOT DIPPING STANDARD 2076 NODULAR CAST IRON CONNECTOR.
HDPE Spacer (Medium Voltage)
Technical Standards: ASTM D2303 - 13 / ASTM D150 - 11 / ASTM G154 - 12aOperating voltage: 8,7/15 kVTracking and weather resistanceVery high impact resistanceMaterial: High density polyethyleneColor: GrayWire diameter: 9 a 32 mmCreepage: 280 mmWeight: 450 grs.Thread diameter: 25 - 35 mmLow radio interference
For comparative tables see technical bulletins on our website www.electricosinter.com
MADE IN COLOMBIA16
www.electricosinter.com
CONTACT
CONTÁCTENOSPBX: (57-1) 432 2950
Celular: (57-1) 311 591 [email protected] Calle 17 No. 42A - 69
Bogotá D.C. - Colombia
Phone:Mobile:E-mail:
Headquarters:
(57)(1) 432 2950(57) 311 591 [email protected] 17 No. 42A - 69Bogotá D.C. - Colombia