591153B 08.17

INSTALLATION GUIDE

US CA

DD24SA & DD24SCT

models

SINGLE DISHDRAWERTM DISHWASHER

1

IMPORTANT! SAVE THESE INSTRUCTIONSThe models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

IMPORTANT SAFETY INSTRUCTIONS ● Installation of this dishwasher requires basic mechanical and electrical skills. ● Be sure to leave these Instructions with the Customer. ● Installation must comply with your local building, electricity, and plumbing regulations. ● At the completion of the dishwasher installation, the Installer must perform the Final

Checklist. ● Remove all packaging materials supplied with the dishwasher. ● This dishwasher is manufactured for indoor use only. ● Ensure all water connections are turned OFF. It is the responsibility of the plumber and

electrician to ensure that each installation complies with all Codes and Regulations. ● The dishwasher MUST be installed to allow for future removal from the enclosure if

service is required. ● The switched power outlet must be outside the dishwasher cavity, so that it is accessible

after installation. ● Care should be taken when the appliance is installed or removed to reduce the likelihood

of damage to the power supply cord and hoses. ● If the dishwasher is to be relocated from one installation to another it must be kept

upright to avoid damage from water spillage. ● Make sure only new hoses are used for connection (supplied with the dishwasher). Old

hoses should not be reused. ● Failure to install the dishwasher correctly could invalidate any warranty or liability claims. ● If the product is installed in a motor vehicle, boat or similar mobile facility, you must

bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product.

● This dishdrawer is intended for connection to the hot-water supply.

WARNING!Electrical Shock HazardBefore installing the dishwasher, remove the house fuse or open the circuitbreaker. If permanently connecting the dishwasher, be sure the power is isolated and the dishwasher unplugged.

GROUNDING INSTRUCTIONSThis appliance must be grounded. In the event of a malfunction or breakdown,grounding will reduce the risk of electric shock by providing a path of leastresistance for electric current. This appliance is equipped with a cord havingan equipment-grounding conductor and a grounding plug. The plug must beplugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded.

If the dishwasher is installed as a permanently connected appliance:GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.Do not modify the power supply plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or multiple outlet box.Failure to follow this advice may result in electrical shock or death.

WARNING!Cut HazardTake care - panel edges are sharp.Failure to use caution could result in injury or cuts.

!

!

1 SAFETY AND WARNINGS

2

2 PARTS SUPPLIED

If the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 3.6 m. The kit is available from the nearest Fisher & Paykel Authorized Service Center or our local website listed at the end of this document.

Clamp (1)(for securing Drain hose joiner)

Wire clip (1) (for securing Drain hose joiner)

Phillips 5/8” (16mm) screws (7)

1 1/2” (38mm)bottom fixing screws & metal washers (2)

Drain hose support (1)

Moisture protection tape (1)(to prevent moisture damage to cabinetry)

Drain hose joiner (1)

Top mountingbrackets (2)OPTIONAL

Rubber washer for inlet hose (1)(comes already fitted)

Side mountingbracket kit(A and B) (2)OPTIONAL

3

2

1

3

3 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

3-A REMOVE THE DRAWER 3-B REMOVE THE ACCESS COVER & REMOVE POWER

Access cover

Clip

Clip

Electronics module

Terminal Block cover

Remove existing power cord

1 With a flat-bladed screwdriver, push in the clips and slide out the access cover.

2 Unscrew the electronics module cover.

3 Carefully pull out the electronics module and rest on the chassis base out of the way.

4 With a screwdriver, unclip the plastic harness cover and hinge open.

5 Slide the terminal block cover sideways to unlock and hinge open to access the terminal block.

6 Unscrew the Live, Neutral and Earth wires as shown.

7 Unscrew the three screws on the base as shown and remove the cord from the product.

1

1

2

3

4

5

6

7

7

4

4

3

3

4” (100 mm)

To prevent kinked hosesEither sit the drawer down on the left hand side (recommended) or rotate the drawer clockwise, resting it on its side after removal.

Press the release tabs in on either side and push back to release drawer from runners.Lift drawer off runners.

Push drawer runners back in on either side.

Push drawer runners back in on either side.

Sit the drawer down

Rotate the drawer clockwise (max. 90o)and rest on side.

4

3 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

IMPORTANT!Ensure the mains wires are routed UNDERNEATH all other harness wiring from the electronics module.

3-D REFIT THE DRAWER ONTO THE RUNNERS & CLOSE

3-C TERMINATE MAINS WIRING AS SHOWN AND REPLACE MODULE AND COVERS

4” (100 mm)

Pull the release tabs forward on both sides 4” (100 mm). Ensure the tabs are fully pulled forward and click into place.

8

9

10

11

12

13 14

8 Fit a suitable cable clamp for the conduit through the metal knockout.

Ensure wiring is routed through or under under housing ribs.

9 Screw down the Live, Neutral and Earth wires correctly.

10 Push the plastic harness cover back over. It should clip back into place

11 Fold down and slide back the terminal block cover.

12 Refit the electronics module back into position, being careful of wiring.

13 Replace the screw securing the electronics module.

14 Slide the access cover back, ensuring the 2 clips shown are fully locked in place.

NOTE: Use copper conductors only.

1

2

3

4

Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward.

Lift or rotate anti-clockwise the drawer back onto the drawer runners on either side.

Release tab

5

4 PRODUCT DIMENSIONS

DD24SA DD24SCT

PRODUCT DIMENSIONS INCHES (MM) INCHES (MM)

A Overall height of product1 16 1/8” (410) 17 7/8” (454)

B Overall width of product 23 9/16” (599) 23 9/16” (599)

C Overall depth of product 22 9/16” (573) 22 9/16” (573)

D Depth of chassis (to back of front drawer panel) 21 3/4” (553) 21 3/4” (553)

E Depth of drawer front panel 13/16” (20) 13/16” (20)

F Height of drawer front panel 15 1/2” (393) 17 3/16” (437)

G Height of chassis1 16 1/8” (410) 17 7/8” (454)

H Height from top of drawer front panel to top of chassis 5/16” (8) 5/16” (8)

I Ventilation gap below drawer front panel 1/4” (7) 1/4” (7)

J Maximum extension of drawer 21 9/16” (547) 21 9/16” (547)

1 includes 1/16” (2mm) high bracket slots

D

J

G

H

I

E

B

F

C

A

PLAN

PROFILEFRONT

6

5 CABINETRY DIMENSIONS

DD24SA DD24SCT

CABINETRY DIMENSIONS INCHES (MM) INCHES (MM)

K Inside height of cavity min. 16 1/4” (412) min. 18” (456)

L Inside width of cavity 23 5/8” (600) 23 5/8” (600)

M Inside depth of cavity min. 22 1/16” (560) min. 22 1/16” (560)

( )

min. 16 1/4”

(412mm)

min. 18”

(456mm)

K K

Dishwasher Dishwasher

DD24SA (Standard height models)

DD24SCT (Tall height models)

Oven

Cavity height options allow you to match dishwasher with your cabinetry or companion products

M

L

K

PROFILE

PLAN

Minimum clearances from adjacent cabinetry

min. 1/2” (13 mm)clearance from a corner cupboard

min. 1/16” (2 mm)clearance to adjacent cupboard door

Bracket slots

7

6 CAVITY PREPARATION

Water Connection

Recommended HOT (Maximum 140°F/60°C).

Supplied hose to suit 3/8” (9 mm) male

Water Pressure Water softener modelsMax. 1 MPa (145 psi)Min. 0.1 MPa (14.5 psi) Models without water softenerMax. 1 MPa (145 psi)Min. 0.03 MPa (4.3 psi)

IMPORTANT!The power outlet must be located in a cabinet adjacent to the dishwasher cavity. 110-120 VAC max. 15 A

min

. 7 7

/8”

(20

0 m

m)

Moisture protection tape must be applied.

Services can be located either side of dishwasher.

COUNTERTOP

IMPORTANT!Adjacent cabinetry must not extend above cavity base.

These marks indicate formed bracket screw locations, if securing by drawer removal.

If there is no side partition, you can construct timber bracing as something to secure into.

3/8” (10mm)

max. 17 11/16” (450mm)

ø max. 1 1/2” (38mm)

Services hole Can be located either side of dishwasher, preferably at the bottom of the cavity, as shown. If adequate clearance, services hole can be made higher to clear toekick space. If hole is higher, ensure drain hose(s) are routed straight into the waste connection.

● If the hole is through wood, make sure its edges are smooth and rounded.

● If the hole is through metal, ensure you fit the supplied Edge Protector to prevent damage to the power cord.

8

7 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE

LEFT HAND SIDE RIGHT HAND SIDE

Drain hose - 78 1/2” (2000 mm) Drain hose - 70 1/2” (1800 mm)

Inlet hose - 64 3/4” (1650 mm) Inlet hose - 49” (1250 mm)

Power cord (excl.plug) - 78 1/2” (2000 mm) Power cord (excl.plug) - 78 1/2” (2000 mm)

9

8 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)

NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE FOR YOUR CABINETRY...

As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted.

IMPORTANT!If product cannot be pushed in far enough, pull out again and rearrange hoses and cord. Do not use excessive force, as doing so may squash the hoses and lead to incorrect operation.

A

A

A

B

B

Clip all four side mounting brackets into their slots using a flat-bladed screwdriver. Ensure they’re securely fitted before sliding product into cavity.

The mounting slots are in pairs, one on each side diagonally across the product. A bracket must match A slot and B bracket must match B slot.

When fitting brackets, ensure the ends are not pushed down into the chassis.

B

AB

9-A ATTACH SIDE MOUNTING BRACKETS !0-A PULL THROUGH HOSES & PUSH INTO THE CAVITY

10

2

1

3

!1-A SECURE TO THE CABINETRY ON THE SIDES

Open the drawer halfway.

Using a flat bladed

screwdriver, prise the grey

rubber plug out of the trim moulding.

Replace the grey rubber plug back intothe trim moulding and ensure the trimseal is facing forward.

Repeat for all four brackets.

Using a small Philips screwdriver,screw through the

trim moulding, securing the side

mounting bracket to the cabinetry. Do not damage

the rubber trimseal.

11

8 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL

9-B PULL THROUGH HOSES & PUSH INTO THE CAVITY !0-B REMOVE THE LOWER DRAWER

As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted.

IMPORTANT!If product cannot be pushed in far enough, pull out again and rearrange hoses and cord. Do not use excessive force, as doing so may squash the hoses and lead to incorrect operation.

2

1

3

4

4

3

3

4” (100 mm)

To prevent kinked hosesEither sit the drawer down on the left hand side (recommended) or rotate the drawer clockwise, resting it on its side after removal.

Press the release tabs in on either side and push back to release drawer from runners.Lift drawer off runners.

Push drawer runners back in on either side.

Push drawer runners back in on either side.

Sit the drawer down

Rotate the drawer clockwise (max. 90o)and rest on side.

12

1

2

1

2

3

4

!2-B REFIT THE DRAWER ONTO THE RUNNERS

!1-B SECURE TO THE CABINETRY ON THE SIDES

Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward.

Lift or rotate anti-clockwise the drawer back onto the drawer runners on either side.

Pull the release tabs forward on both sides 4” (100mm). Ensure the tabs are fully pulled forward and click into place.

Release tab

The product has three pairs of fixing points:

Ensure the sound insulation is repositioned correctly.

a pair of fixing holes either side on the bottom(use 1 1/2” (38mm) fixing screws & washers)

two pairs of formed brackets on either side

of the chassis (use 5/8” (16mm) screws)

4” (100 mm)

13

1

2

!3 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.

DRAINAGE OPTION 1Dishwasher and Ø 1 1/2” (38 mm) Standpipe

IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.

min. R 8” (200mm)

29 1

/2”

- 34

3/4

” (7

50 -

88

2.5

mm

)

1 1/2” (38 mm)

29 1

/2 -

34

3/4

” (7

50 -

88

3mm

)

Screw Drain hose support to back wall

at correct height

If space is limited for fixing, push

hose through drain hose support

to required heightmax.

4 3/4“(120mm)

step 14

min

. 19

11/

16”

(50

0m

m)

14

1

2

min. R 8” (200mm)

IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.

DRAINAGE OPTION 2Dishwasher using Air Break with Drain Hose Joiner

37 3/8” (950mm)Max. height to top of Air Break (countertop or wall mounted)

step 14

Secure drain hose to drain hose joiner and

secure to Air Break

15

3

1

2

min. R 8” (200mm)

IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.

DRAINAGE OPTION 3Dishwasher using drain hose joiner onto sink trap/waste tee

29 1

/2 -

34

3/4

” (7

50 -

88

3mm

)

step 14

Supplied drain hose joiner to suitØ 3/4” (19 mm) waste tee

Ensure drain hose is routed straight to joiner. Remove excess drain hose material if necessary. Do not shorten the inlet hose.

29 1

/2”-

34

3/4

” (7

50 -

88

2.5m

m)

Screw Drain hose support to back wall

at correct height

If space is limited for fixing, push

hose through drain hose support

to required height max. 4 3/4”

(120mm)

min

. 19

11/

16”

(50

0m

m)

16

Ensure the supplied rubber washer is fitted inside the coupling.

Tighten coupling with spanner.

180o

No leaks!

1 2

!4 CONNECT INLET HOSE TO HOT WATER !5 SWITCH PRODUCT ON

17

!6 TROUBLESHOOTING

● Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault)Check for a kinked drain hose, blocked waste connection, highloop not properly installed, drain hose not routed correctly or spray arms not in place.

● No water supply (This is displayed as an A1 fault)Check water is connected and turned on.

● The dishwasher is beeping continuouslyThere is a fault. See section ‘If there is a fault’ in the User guide for further information and instructions.

● No program indicator lights up when the drawer is openedEnsure power is connected and is switched on. If it is and still no indicator lights up, see the ‘Preference options’ section of the ‘Quick start guide’. An option called ‘Open drawer auto power-on’ may need to be turned on.

● Water around water supply and drainage connections Check connections, existing plumbing and hoses for leaks. Check rubber washer and hose clamp are correctly fitted.

● If product is tippingEnsure the product is secured to the cabinetry.

● Drawer doesn’t close properlyEnsure nothing is obstructing the drawer from closing properly eg hoses or drawer latches.

● If a problem occurs, consult the ‘Troubleshooting’ section of the User guide.

● If after checking these points you still need assistance, please refer to the Service & Warranty book for warranty details and your nearest Authorized Service Center, or contact us through our website, listed below.

18

!7 FINAL CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Complete and keep for safe reference:

Model

Serial No.

Purchase Date

Purchaser

Dealer Address

Installer’s Name

Installer’s Signature

Installation Company

Installation Date

Check all parts are installed.

Ensure that all panels and parts thereof are secure and final electrical tests have been conducted in accordance with local electrical regulations.

Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The drawers must be free to fully close with no resistance from the cabinetry.

Ensure inlet hose to water supply has supplied rubber washer fitted, and that it’s tightened a further half turn after seal contact.

Ensure any knockouts or plugs in drain connection have been drilled out and drain connection has been made.

The drain hose joiner must not support the weight of excess hose material. Keep drain hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the highloop.

If connecting the drain hose to the sink trap, ensure the Highloop is a minimum 150 mm higher than the drain hose joiner.

Ensure any packaging or tape securing the racks is removed from the drawers.

Water softener models only: adjust the water softener setting from the default setting to suit the water hardness of the area. See the Quick start guide and section ‘Water softener’ in the User guide.

Turn on the power and water supplies, then open the drawer. You should hear a beep and see a program indicator light up on the control panel.

Check the spray arm is in place, mounted correctly and free to rotate, by physically rotating by hand.

Add three cups of water into the drawer. Press until the indicator of the ‘Rinse’ program lights up. Close the drawer and press to start the program.

After the Rinse program has finished, ensure the dishwasher has run and drained correctly.

Check the water supply has correctly shut off and drainage connection for leakage.

Spray arm

Copyright © Fisher & Paykel Appliances 2017. All rights reserved.The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly

describes the product currently available.

FISHERPAYKEL.COM