
2

Revision History

Date Rev. Originator Summary of Change

31-01-2011 01 SHUBHAM PRASAD Initial development 22-06-2011 02 SHUBHAM PRASAD Removed un-necessary pages

Document Approval

Rev. Role Name Signature Date

01 TI Manager, KENYA Kapadopoulos Vasileios 22-06-2011 TI Manager, KENYA Kenneth Owuor 26-Nov-2014

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This document is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified, or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The document has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this document concerning the suitability, capacity, or performance of the mentioned hardware or software products are given as is and all liability arising in connection with such hardware or software products shall be defined conclusively in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in the document as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENT OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY MONETARY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT

This document and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

Wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright Nokia Siemens Networks 2011. All rights reserved.


3

1. Site Acceptance Certificate

Customer Name: ______________________________________ Date: _______________________

Site Location/Number: __________________________________________________________________

Project Description: ____________________________________________________________________

Nokia Siemens PO #s: __________________________________________________________________

Customer PO #s: _______________________________________________________________________

The above referenced site project (i) has passed all applicable Acceptance Tests, (ii) has been installed properly, subject to resolution of outstanding SDR items, and (iii) is ready to be placed in service.

Any discrepancies are specified on the following SDR or attachment (s).

Installation SDR Dated

No Discrepancies

Quantity of SDR Items

Not Applicable

Site Test Data Forms Dated

No Discrepancies

Quantity of SDR Items

Not Applicable

Customer Representative Nokia Siemens Networks Representative

Signature: ________________________________ Signature: _________________________________

Printed Name: _____________________________ Printed Name: ______________________________

Title: _____________________________________ Title: _____________________________________

Date: ____________________________________ Date: _____________________________________

Distribution: Customer Accounting Project Manager


4

Outstanding Tasks

Item Description of Outstanding Work Raised by: Completed by:

Sig. Sig. 1 Name Name

Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


Date Date


5

1. FLEXI WCDMA BTS INSTALLATION CHECKLIST

The Installation Team is to carry out the Flexi WCDMA BTS Installation in accordance with the Flexi WCDMA BTS User Manual. The Installation Team Supervisor is responsible for:

Ensuring that each team member has the correct tools, installation materials, and User Manual. Checking the delivery against the packing list and placing it in Section 5 of the Site Folder. Completing this checklist, including the signature and date. Completing the necessary Site Deficiency Reports. Completing the necessary Fault Reports. Informing the Installation Manager/Site Manager of work progress, including any problems as they arise. Completing the Certificate of Completion and placing it in Section 1.9 of the Site Folder.


6

1.1 Site Ready Checklist

INSTALLATION PHASE & RELATED DOCUMENTS SDR # COMPLETED

Access/usage permission to building or area is arranged (e.g., keys, security clearance). OK

Lightning protection for antenna system checked. OK Cable ladder/support structure from antenna to entry point to cabinets checked. OK

BTS cabinet position and layout in accordance with Nokia Siemens site-specific documents. OK

Cable ladder position and cable access to top proper side of cabinets for antenna feeder cables, power, and PCM cables checked. OK

Flexi WCDMA BTS equipment grounding busbar or ground cables installed and connected to the main site grounding system. OK

AC power distribution board with clearly labeled fuses/circuit breakers for each cabinet AC checked. OK

Availability of AC mains supply checked. OK Alarm systems installed with cables labeled and run to the Alarm Terminal Block location. OK

1.2 Antenna & Feeder System Installation


Deliveries are complete & checked, shortcomings recorded. OK Equipment is not damaged. OK Antenna layout checked for differences to the drawings and recorded. OK Antenna steelworks grounding checked. OK

Feeder cable routes checked. OK

Feeder wall-throughs checked. NA Feeder cable trays checked. OK Antenna mounting height checked according to the final site configuration. OK Antennas mounted according to site-specific documents. OK Lobe direction checked according to the final site configuration. OK Mechanical tilt angle checked according to the final site configuration. OK Electrical tilt angle checked according to the final site configuration. OK Antenna mounting clamps checked, all screws tightened. OK Connectors mounted according to the mounting instruction of the connector manufacturer. OK


7


Feeder cables mounted according to site-specific documents. NA Feeders grounded and groundings weatherproofed according to grounding instructions. NA

Feeder cables secured on their base. NA Feeder cables marked correctly. NA Jumper connections checked and tightened in the both end of the jumper. OK All external connections checked and sealed. OK BTS jumper connections checked and tightened in the both end of the jumper. OK Jumper cables marked correctly. OK

1.2.1 Antenna / Feeder System Information

SECTOR 1 SECTOR 2 SECTOR 3

Antenna TX/RX RXD TX/RX RXD TX/RX RXD

Line Marked

Tilt Angle

Lobe Direction

Feeder Length

Grounding Kits Used (pcs)


8

1.3 Antenna & Feeder System Test

1.3.1 Antenna VSWR Measurement

Measured VSWR

Sector 1/A Sector 1/B Sector 2/A Sector 2/B Sector 3/A Sector 3/B

NA NA NA NA NA NA

1.3.2 Cable Loss Measurement

Cable loss measurement

Sector 1/A Sector 1/B Sector 2/A Sector 2/B Sector 3/A Sector 3/B

NA NA NA NA NA NA

1.4 Module & Flexi WCDMA BTS Plug-In Unit Inventory

INSTALLATION PHASE Initials & SDR #

Flexi WCDMA BTS plug-in units scanned to file, soft and hard copy attached.

1.5 Site Install Preparation Refer to Nokia Siemens Networks Flexi WCDMA Base Station User Manual.


Site safety is acceptable for work to commence. Site survey is available and complete. Site layout according to drawing. Access permit from owner or authorities available. Grounding busbar for Flexi WCDMA BTS is available. Emplacement for BTS is ready and conforms to Nokia Siemens standards. AC power distribution panel correctly installed and connected to AC mains. Power supply and interface cables ready and conforms to Nokia Siemens standards. Transmission equipment and cables ready and conform to Nokia Siemens standards

Feeders and antenna ready and conform to Nokia Siemens standards BTS delivery is complete and conform to Nokia Siemens standards


9

1.5.1 Delivery


Delivery complete and undamaged. Delivery conforms to site-specific requirements. Delivery conforms to the packing list. Details of any damages/shortages entered into SSD. Packing list placed in SSD.

1.6 Cabinet Installation (if applicable) INSTALLATION PHASE Initials & SDR #

I-Beams / Raised platform installed. Back panel and rear cover installed. NA Cover plate removed. Fixing hole positions on floor marked and drilled. Shims or washers attached to the anchor bolts. BTS installed and tightened to recommended torque settings. BTS level after installation. Door panel installed.

1.7 Cabling Modules in Cabinet Installation

INSTALLATION PHASE Initials & SDR # Grounding cables connected from the BTS to the equipment ground bar. BTS Grounding measured (


10

INSTALLATION PHASE Initials & SDR # Cables are routed correctly. Empty slots are covered with dummy panels (in FCOA installations only). All boots and caps are properly connected and IP-sealed. Only Nokia provided cables are used. Cabinet roof is installed if applicable (in FCOA installations only

1.7.1 Internal Cabling

Flexi WCDMA System Module Front Panel Connector & Labels


11

Flexi WCDMA RF Module Front Panel Connectors

1.8 Finish Installation


Doors installed.

All cables related to BTS are properly labeled.

Main Power supply is switched off.

Power supply units are switched off.

All connectors are tightened with the correct torque recommendation.

Unit install completed.

All spare dummy panels and unused pieces packaged for return to Nokia Siemens.

Packing materials removed from the site.

Rubbish removed and site cleaned and tidy.


12

1.9 Flexi WCDMA Installation Certificate of Completion PO NO:

Customer Name:

Site Name:

Site NO:

Site Address:

Equipment Type:

Configuration ./ Site Type:

Equipment SW Version :

Shipment ID:

The equipment on this site has been installed in accordance with:

DOCUMENT TITLE Nokia Flexi WCDMA Base Station Rel. Flexi WBTS 4.0, (471449A) Document # Issue

STAGE: (Where Applicable) Complete/OK Comments / Deficiency / Outstanding Tasks Equipment / Area/ Customer-specific Instructions followed

Site Installation type & specific instructions followed

Site Prep Complete (T1, Power, Ground, Antenna System)

Transmission check complete & confirmed by RIC

Outstanding Task or Deficiencies:


13

INSTALLATION STAGE COMPLETE / CHECKED (INITIALS) Site Ready Checklist

Delivery is complete and undamaged. Correct P/O and Packing List

Minimum Clearances are met.

Adaptor mechanics are installed. (For Cabinets, walls, H-Frame & pole mounts) Plinth is installed according to the instructions.

Plinth is grounded.

Anti-static wrist strap is connected and used when handling the modules

Modules are installed according to the instructions.

Modules are grounded to the plinth.

Module front and back covers are installed.

Power supply cables are installed per specifications.

Cable entries are installed.

Internal power cables are connected.

Transmission cables are connected.

Optical fiber cables are connected.

Cables between modules on the same plinth are routed via internal cable entries.

BTS external cables or cables b/t modules on different plinths are routed via external cable entries.

IP Connector seals are firmly in place.

Unused connectors are covered with IP seals.

BTS can be started and all LEDs are lit - part of Commissioning activity!

Antenna cables are connected according to the configuration.

Antenna cables are tightened to the correct torque - 25Nm - as per specifications.

Antenna & Feeder System Installation Complete

Antenna & Feeder System Test

Module & Flexi WCDMA BTS Plug-In Unit Inventory

Site Install Preparation

Cabinet Installation (if applicable) Cabling Modules in Cabinet Installation per user Manual

Finish Installation: site is clean and Installation is complete.


14

Nokia Siemens Networks hereby states that the whole of supplies detailed above have been inspected, tested and unless otherwise stated conform to the specified requirements in the contract or order identified above.

Nokia Siemens Site Representative (print name): Date:

PTID No:

Company:

Nokia Siemens Site Representative (signature): Date:

PTID No:

Company

Customer Representative (print name): Date:

Customer Site Representative (signature):


15

2. COMMISSIONING CHECKLIST

The Commissioning Engineer is to carry out all commissioning tests in accordance with the Flexi WCDMA BTS Commissioning Procedure, using the Flexi WCDMA BTS User Manual and other approved reference material. Customer-specific parameters are to be used where applicable. A signed Certificate of Completion for the installation work must be included in Section 1.9 of the Site Folder, certifying that the installation work has been completed to the required standard. The Commissioning Engineer is responsible for:

Checking the quality of the installation. Correcting any installation problems/faults or deficiencies. Familiarization with current Technical Notes.

Commissioning the Flexi WCDMA BTS system in preparation for integration. Completing this checklist, including signature and date. Completing the necessary Site Deficiency Reports. Completing the necessary Fault Reports. Informing the Site Manager of work progress, including any problems as they arise. Completing the Certificate of Completion and placing it in Section 0 of the Site Folder.


16

2.1 Commissioning Overview Site Information

2.1.1 General Information

ITEM VALUE

BTS Name BTS ID BTS IP Address BTS Port # BTS Q1 Address BTS Polling Timeout Recommended Laptop settings (customer) IP Subnet Mask Default Gateway

2.1.2 Software Versions

ITEM VALUE

Module AXC SW Version BTS SW Version

2.1.3 AXC Settings

ITEM VALUE

AXC Configuration soft copy file used and filename recorded

AXC FILENAME AXC Configuration parameters checked and verified

2.1.4 WCDMA Commissioning

ITEM VALUE

WCDMA Commissioning file is available WCDMA Commissioning filename WCDMA Commissioning Events report filed


17

2.1.5 FSMB System Module Settings

ITEM VALUE

Module SW File Module Configuration Module Cross-Connect

2.2 FSMD Module Configuration Views

ITEM VALUE

RF Connection Configuration FSMB Configuration E1/T1 Unit Configuration

2.3 Flexi WCDMA BTS Commissioning Test

ITEM VALUE

Flexi WCDMA BTS Comm. SCF file Flexi WCDMA BTS Comm. Report Flexi WCDMA BTS Hardware report Flexi WCDMA BTS Software report Flexi WCDMA BTS Alarm Log Flexi WCDMA BTS Loop Test report

2.4 Transmitter Measurement

2.4.1 Transmitter Output Power Level

Enter Power Level in W (measured from WAFx Main antenna connector).

Power Level (db)(W)

WTR 1 WTR 2 WTR 3 WTR 4 WTR 5 WTR 6

2.5 Equipment Measurement

MANUFACTURER MODEL SERIAL # LAST CALIBRATION DATE


18

2.6 Finishing

COMMISSIONING PHASE SDR # CHECKED BY

Fill in the Commissioning Certificate of Completion.

Notes on Commissioning


19

Commissioning Certificate of Completion PO NO:

Customer Name:

Site Name:

Site NO:

Site Address:

Equipment Type:



Shipment ID:

The equipment on this site has been commissioned in accordance with:






Site left clean & tidy



20

COMMISSIONING STAGE Basic Checks Pass/Fail

Transmission Check Complete

BTS Grounded Correctly

AC/DC Input Cabled Correctly

Modules cabled correctly

Visual inspection of Modules, Cables, Connectors

Correct Torque Values set on all RF Connectors Proper Installation material used (outdoor rated cabling, power & Ground) Per SE specifications

NSN approved RF Jumper per PL specifications

SW Levels Version BTS SW Release

RNC Adapter SW Release

Java Engine

Site Manager

Site Configuration File

Software update Needed?

External Alarms if applicable (see alarms tab) Pass / Fail External Alarms Configured

External Alarms Tested

File Management Complete Commissioning report reviewed and Uploaded

Bar coding files Uploaded

Site photographs taken and Uploaded

Planned Commissioning Default method Complete View Parameters

Save Parameters

Parameters sent to BTS


21

COMMISSIONING STAGE Manual Commissioning Under direction of RIC Complete

IP Settings

Interface Settings

Transmission Module Settings

Local Call Resources

WCDMA Carrier & Scrambling code settings

Feeder Loss

Parameters saved

BTS Testing Complete BTS Test State Site Tests

BTS Loop Test Performed

BTS BER Test Performed

BTS Restart Parameters consistent!

Mains Fail! 20W / 40W

Finishing Checked (Initials) Comments Site Information

System Module Configuration Views

Flexi WCDMA BTS Commissioning Test

Transmitter Measurement

Equipment Measurement

Finish Commissioning



PTID No:

Company:


PTID No:

Company

RIC Engineer Date:



22

3. INTEGRATION CHECKLIST

The Flexi WCDMA BTS Integration Engineer is to carry out all integration tests in accordance with the Flexi WCDMA BTS User Manual and other approved Integration Procedure. The Integration Engineer is to ensure that a signed Certificate of Completion is produced, certifying that the Flexi WCDMA BTS system has been commissioned and is ready for Integration. The Integration Engineer is responsible for:

Clearing any Installation/Commissioning problems, faults, or deficiencies. Familiarization with current Technical Notes.

Checking that Site Folder documentation is complete. Completing this checklist including signature and date. Completing the necessary Site Deficiency Reports. Completing the necessary Fault Reports. Informing the Site Manager of work progress, including any problems as they arise. Completing the Certificate of Completion and placing it in Section 0 of the Site Folder Completing the Site Acceptance Certificate and placing it in Section 1 of the Site Folder.


23

3.1 Site Integration Test

3.1.1 Integration Tests

ITEM VALUE

Parameters set up SW download done remotely All Alarms tested and cleared Test calls done and recorded to table 1 below Verification of remote access for each Flexi WCDMA Module at the site

All Individual Modules SW and HW version recorded in table 2 below

SECTORS CALL TYPES

MOC/MTC Speech CALL SETUP

HANDOVER TO S1

HANDOVER TO S2

HANDOVER TO S3

Sector 1

Sector 2

Sector 3

Speech Test calls

WCDMA FLEXI TYPE (FIU, LMU, ETC.) SW VERSION HW VERSION

SW and HW version check


24

3.2 Finish Integration Was the Customer present for Integration Activities? Yes No

If yes, Customer Representative Name:

Notes on Integration, Outstanding SDRs:

Completed By: Signature: Date:


25

Integration Certificate of Completion PO NO:

Customer Name:

Site Name:

Site NO:

Site Address:

Equipment Type:



Shipment ID:

The equipment on this site has been Call Tested & Integrated in accordance with:






Site left clean & tidy



26

INTEGRATION STAGE Basic Checks Pass/Fail

Transmission Check Complete

BTS Grounded Correctly

AC/DC Input Cabled Correctly

Modules cabled correctly

Visual inspection of Modules, Cables, Connectors

Correct Torque Values set on all RF Connectors Proper Installation material used (outdoor rated cabling, power & Ground) Per SE specifications

NSN approved RF Jumper per PL specifications

SW Levels Version BTS SW Release

RNC Adapter SW Release

Java Engine

Site Manager

Site Configuration File

Software update needed?

External Alarms if applicable (see alarms tab) Pass/Fail External Alarms Configured

External Alarms Tested

File Management Complete Commissioning report reviewed and Uploaded

Bar coding files Checked

Site photographs Checked

BTS Testing Complete BTS Test State Site Tests

BTS Loop Test Performed

BTS BER Test Performed

BTS Restart Parameters consistent!

Mains Fail! 20W / 40W

Integration Complete BTS Integrated to the Packet Core Network

BTS Integrated to the OSS

Site Integrated with no alarms


27

CALL TESTING STAGE LCR ID Scrambling Code ARFCN

MNC MCC RAC

Voice Call LCR ID Success out of 5 RAC Scrambling Code

Mobile to Land Call Land to Mobile Call Calling Number Called Number Called Number Calling Number

FTP File Data Transfer (time) LCR ID Time to Download (50Mb) Time to Upload (2Mb)

INTRA-BTS Handovers From / To LCR ID Correct Handover A _ B

B _ C

C _ A

A C

C B

B _ A

Emergency Call (A-gps, CI+RTT when available) LCR ID


28

INTEGRATION STAGE CHECKED (INITIALS) COMMENTS

Site Information

System Module Configuration Views

Flexi WCDMA BTS Commissioning Test

Flexi WCDMA BTS Integration Test

Transmitter Measurement

Equipment Measurement

Finish Integration



PTID No:

Company:


PTID No:

Company

RIC Engineer Date:


site folder flexi wcdma bts v02

Documents

site locationnumber

signature date

revision history date

customer comments

mentioned hardware

commissioning checks

installation checks

ti manager