SLINGSHOT-2Polaris Slingshot

2 Speaker SystemSSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

!Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.

WARRANTY INFORMATION:All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

1. SS-FKP652 (1 pair)

2. SSV Works 6.5” Speakers (1 pair)

3. Amplifier

TOOLS NEEDED FOR INSTALLATION PARTS LIST

PARTS LIST IMAGES

4. Audio Input Kit

5. Amplifier Wiring Kit

6. Amplifier Mounting Board

2. SSV Works 6.5” Speakers (1 pair)

6. Amplifier Mounting Board

1. SS-FKP652 (1 pair)

5. Amplifier Wiring Kit

3. Amplifier 4. Audio Input Kit

- 13mm Socket Wrench

- T25, T40 Torx Wrenches

- Wire Crimpers

- Wire Strippers

- Drill with Drill bits

- 1.75” Hole saw (for MRB2 flush mounting)

- #2 and #3 Phillips Screwdriver

- Panel Removal Tool

INSTALLATION NOTESThe use of a thread locker is recommended on all screws to prevent loosening due to vibration. The detailed installation instructions for the SS-FKP652-U speaker pods can be found in the individual box they are packed in. If you are using the MRB2 Bluetooth Receiver as your source, the detailed wiring instructions can be found in that box. Reading all the instructions before beginning the installation is recommended.

D. Remove the two T25 screws and the two panel clips from the underside of each plastic panel on the sides of the dash, remove panel and set aside

C. Using a panel removal tool, unsnap the 2 painted trim panels on the top center of the dash

SLINGSHOT-2

C C

A. Remove the three T25 screws that secure the windscreen, lift and slide the windscreen out of the 2 slots on the bottom of the dash and set aside

B. Remove the mirrors using the 13mm socket

A B

D D D

E. Remove the factory pocket by pulling up and toward the back of the vehicle, lift the pocket slightly to release from the bottom of the panel

F. On either side of the starter switch are 2 panel clips inside the dash opening, remove these using the panel removal tool

G. Remove the two panel clips from the top of the center console side panels

I. Remove the eight T40 Torx screws from the front of the dash

H. Starting at the back of the console, lift the panel up and out. These panels are installed with double sided tape, using the panel removal tool will help break the tape loose

J. Carefully lift the sides of the dash over the mirror brackets and remove the dash from the vehicle and set aside

SLINGSHOT-2

E F

G

I

H

J

H

J

M. Route the amplifier power wire through the center console alongside the main vehicle harness and secure with zip ties, this will run up to the center dash to amplifier mounting location (NOTE: the fuse holder should remain within 12” of the battery

SLINGSHOT-2

M M

K. From the exterior of the vehicle, remove the battery cover by unscrewing the two T40 Torx screws from the lower panel, remove the 2 panel clips from the upper panel using the panel removal tool

O. Remove the two T40 Torx screws from inside the center dash and install the amplifier mounting board using the same two screws

P. Drill a ¼” hole on the bottom of the speaker enclosure for the speaker wire, after running the speaker wire into the enclosure seal the hole with silicone sealer

L. Remove the positive battery clamp from the battery, remove the battery from the compartment and set aside

N. Remove the T40 Torx screw from the factory ground located under the hood, near the center of the firewall. Attach the amplifier ground wire with the ring terminal on the bolt and tighten

K

O P

L

N

Q. Place a speaker into the enclosure and mark the 4 mounting holes, pre drill these holes using the 1/8” drill bit

U. Open the vehicles glove box and remove the rubber plug located next to the 12v socket, using a drill bit open this hole to 1” diameter

R. Connect and install the speaker into the enclosure (be sure to connect the “+” speaker wire to the “+” terminal on the speaker and the “-“ speaker wire to the “-“ terminal on the speaker) using the #2 Phillips screwdriver, attach the triangle block off plate using the M6 screws provided and the #3 screwdriver. Repeat for other side

T. Route the speaker wire to the amplifier mounting location, be sure to keep it away from any moving parts and any sharp metal

B. Loosen the screws on the 2 mounting brackets that are attached to the enclosure. Place enclosure in to the cage; secure the brackets to the cage using the M6 screws and the #3 screwdriver. Attach the curved metal bracket to the underside of the enclosure; be sure it hooks correctly around the cage. Once the enclosure is in place, tighten all the screws. Repeat for other side

V. Remove the nut from the AUX input provided with your Audio Source kit and run the wires through the hole; from the backside of the glove box, install the nut onto the AUX input

SLINGSHOT-2

Q

U

T

R

S

V

R

S

V

SLINGSHOT-2 © 2016 SSV Works, Oxnard, CA 93030 SLINGSHOT-2 Rev. A 2-10-16

WIRING INSTRUCTIONS

For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplifier. If using with an SSV Works complete system refer to the amplifier wiring instructions for more detailed wiring information.

“+”

“+”

“+”

“-”

“-”

“-”

W. Connect the RED wire from the AUX input AND the BLUE amplifier turn on wire to the RED with WHITE stripe wire on the factory 12v socket. Connect the BLACK wire from the AUX input to the BLACK wire on the 12v factory socket. (NOTE: If installing the MRB2 Bluetooth unit as the source connect the RED wire from the MRB2 to the same RED with WHITE stripe wire and the BLACK wire from the MRB2 to the BLACK wire on the 12v socket) .

Y. After all the wiring (Power, Ground, Speaker wires, Amplifier Turn On & Input cables) are ran to the Amplifier mounting location, wire the amplifier and mount to the amplifier mounting board. (NOTE: Refer to the instructions included in the amplifier for detailed wiring and tuning instructions

X. The location indicated above is an ideal location for either the Volume control for the AUX input source or the controller for the MRB2 Bluetooth source. To mount the volume control, drill a ¼” hole, remove the knob by pulling off the shaft, remove the nut from the shaft, insert the shaft into the hole, and replace the nut and the knob. If you are using the MRB2 Bluetooth source unit, refer to the instructions included in the box for detailed mounting options.

W

Y Z

X

Z. After fully testing the audio system, reinstall all panels and parts that have been removed in the reverse order of removal.

Battery+ -

Amplifier

Audio Input Kit