snow blower om · 2019-05-20 · ultra snow blower owner’s manual 5 introduction owner...

10035September 2014

Proof 9-4-14

Proof 9-4-14

CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Owner Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Snow Blower Idenification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Features And Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Options And Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Owners Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Operating Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Decal Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Welding And Grinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Fire Extinguishers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Decal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Daily Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Snow Blower Mounting Frame 18Wear Shoe 18Cutting Edge 18

Entering And Exiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Snow Blower Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Hydraulic Couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Attachment Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Snow Blower Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Snow Blowing Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Cleaning The Discharge Cute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Snow Blower Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32Reversing The Cutting Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33Cutting Edge Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33Wear Shoe Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Wear Shoe Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Return To Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Ultra Snow Blower Owner’s Manual 1

Proof 9-4-14

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39Ultra Snow Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4338000-K Snowblower Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43Valve Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44Snow Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

HYDRAULIC SCHEMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

MANUFACTURER’S WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

2 Ultra Snow Blower Owner’s Manual

Proof 9-4-14

INTRODUCTION


Proof 9-4-14


Proof 9-4-14

INTRODUCTION

Owner Information

Thank you for your decision to purchase a snow blowerfrom SnowWolf. To ensure maximum performance ofyour snow blower, it is mandatory that you thoroughlystudy the owner’s manual and follow itsrecommendations. Proper operation and maintenanceare essential to prevent injury or damage and tomaximize the life of the snow blower.

Operate and maintain the snow blower in a safemanner and in accordance with all applicable local,state, and federal codes, regulations and/or laws.

Make sure that all personnel have read this owner’smanual and thoroughly understand safe and correctoperating, installation and maintenance procedures.

Continuous improvement and advancement ofSnowWolf products may result in changes to yourequipment that may not be reflected in this publication.SnowWolf reserves the right to make productimprovements to the snow blower at any time.Although great care has been taken to ensure theaccuracy of this publication, SnowWolf does notassume any liability for errors or omissions

Serial Number Location

Figure 1

The snow blower serial number plate (Item 1) [Figure1] is located on the frame.

Always use the serial number of the snow blower whenrequesting service information or when ordering parts.Early or later models (identification made by serialnumber) may use different parts, or may require adifferent procedure in doing a specific serviceoperation.

NOTE: This document and the informationprovided are the property of SnowWolf andmay only be used as authorized bySnowWolf.

1


Proof 9-4-14

INTRODUCTION (CONT’D)

Snow Blower Idenification

DEFLECTOR DEFLECTOR CYLINDER

DISCHARGE CHUTEMOTOR

ATTACHMENT MOUNTING FRAME

CUTTING EDGE

AUGER MOTOR

AUGER


Proof 9-4-14

INTRODUCTION (CONT’D)

Features And Accessories

Standard Items

The snow blower is equipped with the followingStandard Items:

• Rotating Discharge Chute

• Hydraulic Operated Deflector

• Replaceable Bolt-On Cutting Edge

• Universal Skid Steer Mounting Plate

• Drif Cutters

• Rubber Deflectors

Options And Accessories

Below is a list of Options and Accessories available forthe snow blower. See your SnowWolf dealer for otheravailable options and accessories.

• Mounting Plates

• Carbide Edge

• / Adapters

• Joystick Controller


Proof 9-4-14

Bruce

Rectangle

Bruce

Sticky Note

Is there any pictures or information for these?

Bruce

Rectangle


Proof 9-4-14

SAFETY


Proof 9-4-14


Proof 9-4-14

SAFETY

Safety Information

This section covers recommended safety instructions,along with other general recommendations and specificmachine safety precautions that must be readthoroughly before operating the machine.

NOTE: A reminder of other related information thatneeds to be considered.

Operator must have instructions before operating themachine. Untrained operators can cause injury ordeath.

Be certain all equipment operators are aware of thedangers indicated by safety decals applied to theequipment, and be certain they follow all safety decalinstructions. Contact your authorized Distributor,Dealer Parts Department or SnowWolf for safety decalreplacement.

Do not modify the snow blower in any way.Unauthorized modification may impair the function and/or safety of the components and systems and couldaffect the life of the equipment, possibly invalidating thewarranty coverage.

SnowWolf cannot anticipate every possiblecircumstance that may involve a potential hazard. Thewarnings in this owner’s manual are not all inclusive.

This symbol with a warning statement means:“Warning, be alert! Your safety is involved!”Carefully read the message that follows.

Safety Alert Symbol

This signal word DANGER on the equipment or in themanual indicates a potentially hazardous situationwhich, if not avoided, will result in severe personalinjury or death.

This signal word WARNING on the equipment or inthe manual indicates a potentially hazardous situationwhich, if not avoided, could result in severe personalinjury or death.

The signal word CAUTION on the machine and in themanual indicates a potentially hazardous situationwhich, if not avoided, MAY result in minor ormoderate injury. It may also be used to alert againstunsafe practices.

This notice identifies procedures which must befollowed to avoid damage to the machine.


Proof 9-4-14

SAFETY (CONT’D)

Owners Responsibility

Operate and maintain the snow blower in a safemanner and in accordance with all applicable local,state, and federal codes, regulations and/or laws.

Make sure that all personnel have read this owner’smanual, and thoroughly understand safe and correctinstallation, operation and maintenance procedures.

Give operating instructions to the operators beforeallowing them to operate the machine.

Fulfill all warranty obligations so as not to void thewarranties. The warranty policy outlines the warrantypolicy of SnowWolf.

• Do not allow anyone to operate the machine until heor she has read the owner’s manual and iscompletely familiar with all safety precautions.

• Do not allow inexperienced persons unfamiliar withthe machine, or unfamiliar with safe operating andmaintenance procedures for the equipment tooperate or maintain the machine.

• Do not allow persons under the influence of alcohol,medications, or other drugs that can impairjudgement to operate or maintain the machine.

• Wear safety glasses, gloves, hearing protectionand other protective clothing when required.

• Before you service the snow blower, remove thekey from the machine and place a Do Not Operatetag on the machine or remove the snow blower fromthe machine.

• Do not replace components or parts with other thanfactory-recommended service parts. To do so maydecrease the effectiveness and/or the safety of themachine.

• Do not modify the snow blower in any way. Un-authorized modification can result in serious injuryor death and may impair the function and life of thesnow blower.

• Never operate the machine in an enclosed area.Proper ventilation is required under allcircumstances.

• Have a first-aid kit available for use should the needarise and train personnel on proper use of the kit.

• Review safety related items annually with allpersonnel who will be operating, using ormaintaining the snow blower.

Operating Safety

Failure to comply with the following messages couldresult in death or serious injury.

• Use care when climbing on frame to preventslipping or falling.

• Install and secure all guards before operating.

• Be aware of all pinch points on the machine andkeep clear.

• Do not wear loose hanging clothing. Theseprecautions will help prevent you from becomingcaught in the moving parts or on levers and latcheson the machine.

• Keep all bystanders away from the machine whenloading or unloading is being done.

• Watch for adequate overhead clearance whenoperating the machine.

• Stay away from overhead power lines.Electrocution can occur without direct contact.

• Never attempt to clear obstructions or objects fromthe snow blower while the machine is running.

Warnings on the machine and in the manuals are foryour safety. Failure to obey warnings can causeserious injury or death.

These are general safety considerations.Additional precautions may be necessary tooperate your equipment in a safe manner. Becertain you are operating your equipment inaccordance with all safety codes, OSHA rules andregulations, insurance requirements; and local,state and federal laws.


Proof 9-4-14

SAFETY (CONT’D)

Operating Safety (Cont’d)

• Stop engine, remove ignition key and wait for allmoving parts to stop before servicing, repairing,adjusting or loading.

• Escaping hydraulic fluid under pressure can havesufficient force to penetrate skin, causing seriousinjury. NEVER check for leaks by using any part ofyour body to feel for escaping fluid.

• Periodically check all hose connections, pressuresand temperatures. Replace or repair anything thatcould cause a potential hazard.

• Before servicing, make sure the machine hascooled down. Machine components, hoses andfittings can get hot enough to cause serious injury.

• The snow blower should not be used to handlematerials other than which were specified as part ofits design.

Decal Replacement

• Keep all safety signs and reflectors clean andlegible at all times.

• Replace safety signs and reflectors that are missingor have become illegible.

• Replaced parts that displayed a safety sign, mustalso display the current sign.

• Contact your authorized Distributor, Dealer PartsDepartment or SnowWolf for safety decalreplacement.


Proof 9-4-14

FIRE PREVENTION

Maintenance

The equipment may have components that are at hightemperatures under normal operating conditions. Theprimary source of high temperatures is the engine andexhaust system. The electrical system, if damaged orincorrectly maintained, can be a source of arcs orsparks.

Flammable debris must be removed regularly. Ifflammable debris is allowed to accumulate, it cancause a fire hazard.

All fuels, most lubricants and some coolant mixturesare flammable. Flammable fluids that are leaking orspilled onto hot surfaces or onto electrical componentscan cause a fire.

Operation

Do not use the equipment where exhaust, arcs, sparksor hot components can contact flammable material,explosive dust or gases.

Electrical

Check all electrical wiring and connections for damage.Keep the battery terminals clean and tight. Repair orreplace any damaged part or wires that are loose orfrayed.

Battery gas can explode and cause serious injury. Usethe procedure in the Operation & Maintenance Manualfor connecting the battery and for jump starting. Do notjump start or charge a frozen or damaged battery.Keep any open flames or sparks away from batteries.Do not smoke in battery charging area.

Hydraulic System

Check hydraulic tubes, hoses and fittings for damageand leakage. Never use open flame or bare skin tocheck for leaks. Hydraulic tubes and hoses must beproperly routed and have adequate support and secureclamps. Tighten or replace any parts that showleakage.

Always clean fluid spills. Do not use gasoline or dieselfuel for cleaning parts. Use commercial nonflammablesolvents.

Fueling

Stop the engine and let it cool before adding fuel. Nosmoking! Do not refuel a machine near open flames orsparks. Fill the fuel tank outdoors.

Starting

Do not use ether or starting fluids on any engine thathas glow plugs. These starting aids can causeexplosion and injure you or bystanders.

Use the procedure in the Operation & MaintenanceManual for connecting the battery and for jump starting.

Welding And Grinding

Always clean the equipment, disconnect the battery,and disconnect the wiring before welding. Cover rubberhoses, battery and all other flammable parts. Keep afire extinguisher near the equipment when welding.

Have good ventilation when grinding or weldingpainted parts. Wear dust mask when grinding paintedparts. Toxic dust or gas can be produced.

Dust generated from repairing nonmetallic parts can beflammable or explosive. Repair such components in awell ventilated area away from open flames or sparks.


Proof 9-4-14

Fire Extinguishers

Know where fire extinguishers and first aid kits arelocated and how to use them. Inspect the fireextinguisher and service the fire extinguisher regularly.Obey the recommendations on the instructions plate.


Proof 9-4-14

SAFETY (CONT’D)

Decal Locations


Proof 9-4-14

Bruce

Sticky Note

Are there part numbers for decals?

OPERATION


Proof 9-4-14

OPERATION

Daily Inspection

Snow Blower Mounting Frame

Figure 2

Inspect the wedge mounts (Item 1), mounting flange(Item 2) [Figure 2] and all welds on the snow blowermount for wear and damage each time the snowblower is removed from the machine.

Frequently inspect the snow blower to ensure that allcomponents are secure and that all bolts and nuts arethoroughly tightened.

Wear Shoe

Figure 3

Inspect the wear shoes (Item 1) [Figure 3] for wear ordamage.

NOTE: If the wear shoe is worn or damaged,replace the wear shoe. (See Wear ShoeReplacement on page 34.)

NOTE: Make sure wear shoes are adjusted to thesame height, adust if necessary. (See WearShoe Adjustment on page 34.)

Cutting Edge

Figure 4

Inspect the cutting edge (Item 1) [Figure 3] for wear ordamage.

NOTE: If the cutting edge is worn or damaged,reverse or replace the cutting edge. (SeeReversing The Cutting Edge on page 33.) or(See Cutting Edge Replacement on page33.)

1 1

2

1

1


Proof 9-4-14

OPERATION (CONT’D)

Entering And Exiting

NOTE: Operators are injured and killed by movingparts when not entering or exiting themachine safely. (See the machine’sOperation Manual for the correctprocedure.)

Entering

Use the attachment steps, grab handles and safetytreads to get on and off the machine.

Figure 5

Enter the machine. Fasten the seat belt and adjust thebuckle so the buckle is centered between your hips[Figure 5].

Figure 6

Lower the seat bar (if equipped) and engage parkingbrake [Figure 6].

Place all controls in neutral position.

See the machine’s Operation Manual for detailedinformation on operating the machine.

Exiting

Lower the lift arms and put the attachment flat on theground.

Stop the engine and engage the parking brake.

Lift the seat bar (if equipped) and make sure the lift andtilt functions are deactivated.

Remove the key.

Exit the machine. (See the machine’s OperationManual of the correct procedure.)

AVOID INJURY OR DEATHWhile operating the machine:• Always keep seat belt fastened.• Safety seat bar lowered (if equipped).• Always keep your feet on the pedals or

footrests and hands on the controls.

AVOID INJURY OR DEATH

Before you exit the machine:• Lower the lift arms, put the attachment flat on

the ground.• Stop the engine and engage the parking

brake.• Move all controls until they are LOCKED or in

the NEUTRAL position• Lower the lift arms, put the attachment flat on

the ground.

SEE THE MACHINE’S OPERATION MANUAL FORMORE INFORMATION.


Proof 9-4-14


Snow Blower Installation

WARNING

Warnings on the machine and in the manuals arefor your safety. Failure to obey warnings can causeserious injury or death.

W-001

Always inspect the machine’s attachment mountingplate and the snow blower mounting frame beforeinstallation. See the machine’s Operation Manual. (SeeDaily Inspection on page 18.)

Fully raise the attachment locking levers.

Enter the machine. (See Entering And Exiting on page19.)

Start the engine and release the parking brake.

Lower the machine’s lift arms and tilt the attachmentmounting plate forward.

Figure 7

Drive the machine slowly forward until the top edge(Item 1) of the attachment mounting plate is completelyunder the top flange (Item 2) [Figure 7] of the snowblower mounting frame.

NOTE: Be sure the attachment locking levers donot hit the attachment during installation.

Tilt the attachment mounting plate backward, raisingthe snow blower slightly off the ground. This will causethe snow blower mounting frame to fit against theattachment mounting plate.

Stop the engine and exit the machine. (See EnteringAnd Exiting on page 19.)

Figure 8

Lower the attachment locking levers (Item 1)[Figure 8] into the locked position.

1

2






the ground.


1


Proof 9-4-14


Snow Blower Installation (Cont’d)

Figure 9

The machine’s attachment mounting wedges mustextend through the holes (Item 1) [Figure 9] in thesnow blower mounting frame, to securely fasten thesnow blower to the attachment mounting plate.

Hydraulic Couplers

Verify that the attachment hydraulic couplers match themachine’s auxillary hydraulic couplers. If the couplersdo not match, the attachment couplers will need to bechanged to match the machine’s auxillary hydrauliccouplers.

To Connect:

Remove any dirt or debris from the surface of both themale and female couplers, and from the outsidediameter of the male coupler. Visually check thecouplers for corroding, cracking, damage, or excessivewear. If any of these conditions exist, replace thecoupler(s).

Install the male coupler into the female coupler. Pull onthe coupler connection to verify that the male andfemale couplers securely fastened.

To Disconnect:

Relieve hydraulic pressure. (See the machine’sOperation Manual for correct procedure.)

Push the couplers together, retract the sleeve on thefemale coupler until the couplers disconnect.

The attachment mounting wedges must extendthrough the holes in the attachment mountingframe. Attachment locking levers must be fullylowered and locked. The attachment can come offif the wedges are not secured.

1 1

• Thoroughly clean the quick couplers beforemaking connections. Dirt can quickly damagethe system.

• Contain and dispose of any oil leakage in anenvironmentally safe manner.

AVOID BURNS

Hydraulic fluid, tubes, fittings and quick couplerscan get hot when running machine andattachments. Be careful when connecting anddisconnecting quick couplers.


Proof 9-4-14


Attachment Control Functions

NOTE: After installing the snow blower, test allsnow blower functions before operating thesnow blower in the work area.



Engage the machine’s auxilliary hydraulics. (See themachine’s Operation Manual for correct procedure.)

Move the engine speed control to high rpm.

Auger Rotation

Start auger rotation. Allow the snow blower auger torotate for a short time (approximately one minute).

Stop auger rotation.

Chute Rotation

Rotate the discharge chute in both directions. Thedischarge chute should rotate freely. Adjust chaintension if needed.

Raise / Lower The Deflector

Raise and lower the deflector multiple times. Thedeflector should move up and down freely.

Lower engine RPM.

Disengage the machine’s auxiliary hydraulics.

Slightly raise the snow blower.

Move the machine and snow blower to the work area.

AVOID INJURY OR DEATH• Never start the machine from outside the cab.• Never operate the machine if any safety

device is damged, disconnected or missing.• Never exit the machine with the engine

running.

It is the operator’s responsibility to know whichmachine control operates each function of theattachment prior to operating the attachment inthe work area.



When engaging or disengaging the snow blowerhydraulics the machine must be at idle. Hydrualicmotor damage will occur if this procedure is notfollowed, voiding warranty.


Proof 9-4-14


Snow Blower Operation





Rotate the discharge chute to the desired position.

NOTE: Do not position the discharge chute sosnow is thrown towards bystanders,vehicles, buildings livestock or roadways.

Adjust the deflector to control the distance the snow isthrown.

NOTE: The distance the snow is thrown isdetermined by the density of the snow.

Place the machine arms in the float position (ifdesired).

Figure 10

Using the tilt function of the machine, position the snowblower on the cutting edge.

Position the snow blower on the cutting edge whenremoving snow from paved / finished sufaces.

Position the snow blower on the wear shoe whenremoving snow from graveled / unfinished surfaces.

NOTE: The machine speed is determined by thedepth and density of the snow.

Warnings on the machine and in the manuals arefor your safety. Failure to obey warnings cancause serious injury or death.


• Check for overhead power lines and otheroverhead obstructions before operating thesnow blower in a raised position.

• Keep the snow blower a minimum of 10 ft.away from electrical power lines.




Never direct discharge toward bystanders,building or other property. Debris can be throwngreat distances.

When engaging or disengaging the snow blowerhydraulics the machine must be at idle. Hydrualicmotor damage will occur if this procedure is notfollowed, voiding warranty.


Proof 9-4-14


Snow Blowing Recommendations

Work and Travel Speed

Working ground speed will depend upon the depth anddensity of the snow. Adjust speed as needed to clearthe work area.

NOTE: A definite pattern of operation is required tothoroughly clean the work area. Thefollowing patterns will aid the operator andavoid throwing snow in unwanted areas ofthe work area.

Left or Right Discharge

Figure 11

Where it is possible to throw the snow to the left andright sides of the work area, move the machine andsnow blower to the center of the work area [Figure 11].

Move the machine and snow blower forward, from oneend to the other, blowing snow to either side withoutchanging the direction of the discharge chute[Figure 11].

Single Sided Discharge

Figure 12

Where snow can only be thrown to one side, move themachine and snow blower to opposite end of the workarea, away from the area the snow will be thrown[Figure 12].

Move the machine and snow blower forward. At theend of the first path, rotate the dischage chute 180° tomaintain direction the snow needs to be thrown. Rotatethe discharge chute 180° at each end of the work areauntil desired amount of snow has been cleared[Figure 12].

SNOW THROWN TO EITHER SIDE

SNOW THROWN TO EITHER SIDE

SNOW THROWN TO SIDE ONLY

NO SNOW THROWN TO THIS SIDE


Proof 9-4-14


Snow Blower Operation (Cont’d)

Clearing a Snow Bank

NOTE: Do not attempt to clear snow banks that aremore than (6 ft.) in height.

Figure 13

Raise the snowblower to the desired height. Using thetilt function of the machine, position the snowblowerparallel to the ground.

Slowly drive forward until the front wheels / tracks ofthe machine contact the snow bank.

Back the machine up and adjust the blower to desiredheight and repeat procedure until the snow bank hasbeen cleared or cut to desired height.


• Check for overhead power lines and otheroverhead obstructions before operating thesnow blower in a raised position.

• Keep the snow blower a minimum of 10 ft.away from electrical power lines.


Proof 9-4-14


Cleaning The Discharge Cute

If the discharge chute plugs, move the machine andsnow blower to a flat level surface of the work area.

Lower the lift arms and put the snow blower flat on theground.

Stop the engine and exit the machine. (See EnteringAnd Exiting on page 19.)

Remove the packed snow from the discharge chute.

Also remove all packed snow from the auger andimpeller areas of the snow blower.





Test the functions of the snow blower.

If all snow blower functions operate correctly, raise thesnow blower slightly off the ground and move themachine and snow blower to work area and continueclearing snow.


• Do not use hands or feet to unplug thedischarge chute.

• Do not attempt to unplug the discharge chutewhile the engine is running.






the ground.



Proof 9-4-14


Snow Blower Removal

Lower the lift arms and put the snow blower flat on theground.

NOTE: Put the snow blower on planks or blocksbefore removing the snow blower from themachine to prevent the snow blower fromsettling or sinking in soft / wet ground.

Stop the engine and release auxiliary hydraulicpressure.

Exit the machine. (See Entering And Exiting on page19.)

Disconnect auxiliary hydraulic hoses. (See HydraulicCouplers on page 21.)

Fully raise the attacment locking levers.



Figure 14

Tilt the attachment mounting plate forward and drivethe machine backward, away from the snow blower[Figure 14].






the ground.



Proof 9-4-14


Proof 9-4-14

MAINTENANCE


Proof 9-4-14


Proof 9-4-14

MAINTENANCE

Troubleshooting

Use the following troubleshooting chart to locate and correct problems which most often occur with the snow blower.

PROBLEM CAUSE CORRECTION

Snow Blower does not operate. Machine’s main relief valve set too low.

Adjust main relief valve to correct setting.

Machine’s fluid reservoir is too low. Add hydraulic fluid to the fluid reservoir on the machine.

Machine’s hydraulic pump faulty. Check flow of hydraulic pump. Repair or replace as needed.

Attachment control wire harness damaged or not connected properly to valve block.

Check connections, repair or replace wire harness.

Snow blowers hydraulic valve block faulty.

Repair or replace valve block.

Damaged quick couplers. Replace quick couplers.

Auxiliary hydraulics not engaged. Engage auxiliary hydraulics.

Chute does not rotate. Damaged hydraulic motor. Repair or replace.

Loose or broken chute rotation chain. Repair or replace.

Deflector does not adjust. Damaged cylinder. Repair or replace.

Snow Blower cuts too low. Wear shoes out of adjustment. Raise or lower wear shoes as needed.

Snow Blower leaving snow behind. Cutting edge worn or damaged. Replace or reverse the cutting edge.

Snow blower tilted to far forward. Adjust machines lift and tilt controls.


Proof 9-4-14

MAINTENANCE (CONT’D)

Lubrication

Use a quality lithium base grease when lubricating thesnow blower.

Figure 15

Grease the fitting (Item 1) [Figure 15] every 10 hoursof operation.

Use a quality chain lubricant when lubricating thedischarge chute chain.

Figure 16

Lubricate the chain (Item 1) [Figure 16] every 10 hoursof operation.

1

1


Proof 9-4-14


Reversing The Cutting Edge

Use a lifting device and/or chains to raise the snowblower slightly off the ground. Securely block up andsupport the snow blower.

NOTE: Use chains that are in good condition and ofadequate size to lift the attachment.

Figure 17

Remove the bolts (Item 1), nuts and cutting edge (Item2) [Figure 17].

Rotate the cutting edge 180° or until the worn side isfacing up.

Install bolts, nuts and tighten.

Cutting Edge Replacement

Use a lifting device and/or chains to raise the snowblower slightly off the ground. Securely block up andsupport the snow blower.

NOTE: Use chains that are in good condition and ofadequate size to lift the attachment.

Remove the bolts (Item 1), nuts and cutting edge (Item2) [Figure 17].

Install new cutting edge, install bolts, nuts and tighten.


Always wear safety glasses to prevent eye injurywhen any of the following conditions exist:• Engine is running.• Flying debris or loose material is present.• When tools are being used.• When fluids are under pressure.


Securely block up the snow blower beforeworking underneath.

1

2




Proof 9-4-14


Wear Shoe Replacement

Place blocks under the snow blower (both sides) tohold the wear shoes off the ground.

Figure 18

Remove retaining pin (Item 1), spacers (Item 2) andwear shoe (Item 3) [Figure 18].

Before installing the new wear shoe onto the snowblower, install spacers onto the shaft (if needed). (SeeWear Shoe Adjustment on page 34.)

Install the wear shoe onto the snow blower. Installremaining spacers and retaining pin.

Wear Shoe Adjustment

Place blocks under the snow blower (both sides) tohold the wear shoes off the ground.

Figure 19

Remove the retaining pin (Item 1), spacers (Item 2)and the wear shoe (Item 3) [Figure 19].

Lowering / Raising The Wear Shoe

Install or remove spacers onto the shaft of the wearshoe to obtain the desired height. Install the wear shoeonto the snow blower. Install remaining spacers ontothe shaft of the wear shoe and install the retaining pin.

NOTE: If the wear shoes are not installed properly,the weight of the snow blower will be putupon the retaining pin instead of thewashers and may cause breakage.

Repeat procedure on the other side, making sure bothwear shoes are adjusted to the same height.



1

3

2



1

3

2


Proof 9-4-14


Storage

After the seasons use or when the snow blower will notbe in use for a period of time, perform the followingsteps.

• Thoroughly wash the snow blower.

• Inspect the snow blower frame and all welds forcracks or damage.

• Inspect all components and hardware to ensureeverything is secure and thoroughly tightened.

• Lubricate the snow blower.

• Inspect optional equipment (if equipped).

• Check for missing or damaged decals. Replace ifnecessary.

• Place the snow blower in a dry protected shelter.

NOTE: Replace or repair any damaged parts.

Return To Service

After the snow blower has been in storage, it isnecessary to follow a list of items to return the snowblower to service.

• Be sure all shields and guards are in place.

• Inspect optional equipment (if equipped).

• Inspect decals for damage.

• Lubricate the attachment / implement.

• Install and operate the snow blower and check forcorrect function.

• Check for leaks. Repair as needed.


Proof 9-4-14


Proof 9-4-14

SPECIFICATIONS


Proof 9-4-14


Proof 9-4-14

SPECIFICATIONS

Ultra Snow Blower

DESCRIPTION SSB-51 SSB-60 SSB-84

Overall Height (A) (Deflector Raised) 83.76 in 83.76 in 83.76 in

Overall Height (B) (Deflector Lowered) 77.15 in 77.15 in 77.15 in

Overall Length (C) 52.61 in 52.61 in 52.61 in

Cutting Height (D) 40.33 in 40.33 in 40.33 in

Oveall Width (E) 55.61 60.61 88.61 in

Cutting Width (F) 51 in 60 in 84 in

Cutting Edge 1/2” x 6” 1/2” x 6” 1/2” x 6”

Weight XXXX lb. 1,420 lb. 1680.25 lb.

Wear Shoes Cast Iron Cast Iron Cast Iron

Hook Up Skid Steer Mount Skid Steer Mount Skid Steer Mount

Hydraulic Flow (required) 28 - 45 gpm 28 - 45 gpm 28 - 45 gpm

Hydraulic Pressure (required) 3000 - 4000 psi 3000 - 4000 psi 3000 - 4000 psi

B

C

D

A

E

F


Proof 9-4-14

Bruce

Sticky Note

Is there a weight for the SSB-51?

HARDWARE TORQUE VALUES (CONT’D)

Chart

Use the following chart to determine the correct torque when checking, adjusting or replacing hardware. Torquevalues are listed in newton-meters (inch* or foot pounds) for normal assembly applications.

Nominal Size

SAE GRADE 5 SAE GRADE 8 LOCK NUTS

Unplated or Plated

Silver

PlatedW / ZnCr

Gold

Unplated or Plated

Silver

PlatedW / ZnCr

Gold

Unplated or Plated

Silver

PlatedW / ZnCr

Gold

GradeW / Gr. 5

Bolt

GradeW / Gr. 8

Bolt

1/4 6.2 (55*) 8.1 (72*) 9.7 (86*) 12.6 (112*) 13.6 (121*) 17.7 (157*) 6.9 (61*) 9.8 (86*)

5/16 13 (115*) 17 (149*) 20 (178*) 26 (229*) 28 (250*) 37 (324*) 14 (125*) 20 (176*)

3/8 23 (17) 30 (22) 35 (26) 46 (34) 50 (37) 65 (48) 26 (19) 35 (26)

7/16 37 (27) 47 (35) 57 (42) 73 (54) 80 (59) 104 (77) 41 (30) 57 (42)

1/2 57 (42) 73 (54) 87 (64) 113 (83) 123 (91) 159 (117) 61 (45) 88 (64)

9/16 81 (60) 104 (77) 125 (92) 163 (120) 176 (130) 229 (169) 88 (65) 125 (92)

5/8 112 (83) 145 (107) 174 (128) 224 (165) 244 (180) 316 (233) 122 (90) 172 (127)

3/4 198 (146) 256 (189) 306 (226) 397 (293) 432 (319) 560 (413) 217 (160) 306 (226)

7/8 193 (142) 248 (183) 495 (365) 641 (473) 698 (515) 904 (667) 350 (258) 494 (364)

1 289 (213) 373 (275) 742 (547) 960 (708) 1048 (773) 1356 (1000) 523 (386) 739 (545)

NOTE: Torque values shown with * are inch pounds.

Identification of Hex Cap Screws and Carriage Bolts

Identification of Hex Nuts and Lock Nuts

SAE GRADE 2 BOLTS

SAE GRADE 5 BOLTS

SAE GRADE 8 BOLTS

SAE GRADE 2 NUTS

SAE GRADE 5 NUTS

SAE GRADE 8 NUTS

B

Grade A - No Notches

Grade B - One Circumferential Notch

Grade C - One Circumferential Notches

Grade A - No Mark

Grade B - Letter B

Grade C - Letter C

Grade A - No Marks

Grade B - Three Marks

Grade C - Six Marks

(Marks not always located at corners)


Proof 9-4-14

PARTS IDENTIFICATION


Proof 9-4-14


Proof 9-4-14

PARTS IDENTIFICATION

38000-K Snowblower Kit

Kit Includes Adapters and Hoses

PART NO. DESCRIPTION QTY.

P38110 ADAPTER, 12ORB / 12MJIC 5

P38120 ADAPTER, 16ORB / 12MJIC 2

P38130 90° ADAPTER, 4MORB / 4MJIC 1

P38125 90° ADAPTER, 6ORB / MJIC 5

P38126 45° ADAPTER, 12MJIC / 12FJIC 2

P38115 90° ADAPTER, 12ORB / 12MJIC 1

P38135 90° ADAPTER, 6MJIC / 10ORB 2

P38105 90° ADAPTER,160RB / 12MJIC 2

P38050 HOSE, 3/4” x 104” 2

P38015 HOSE, 3/4” x 22 1/2” 1

P38025 HOSE, 3/4” x 23” 1

P38010 HOSE, 3/4” x 19” 1

P38020 HOSE, 3/4” x 24” 1

P38035 HOSE, 1/4” x 84” 1

P38030 HOSE, 1/4” x 80” 1

P38036 HOSE, 1/4” x 53” 1

P38047 HOSE,1/4” x 52” 1

P38040 HOSE, 1/4” x 24” 1

P38210 HOSE PROTECTOR 72” 1





Proof 9-4-14

PARTS IDENTIFICATION (CONT’D)

Valve Block

1

2

3

5

6

3

78

9

9

10

11

12

12

13

14

15

4


Proof 9-4-14


Valve Block (Cont’d)

ITEM PART NO. DESCRIPTION QTY.

1 P30021 BLOCK, MANIFOLD 1

2 P30022 PLUG, EXPANDER 7 MM 8

3 P30027 PLUG, ZERO LEAK 4

4 P30024 SPRING, COMPRESSION 1

5 P30025 PLUG, ZERO LEAK 1

6 P30023 POPPET 1

7 P30029 VALVE, RELIEF, 2500 PSI 1

8 P30028 ELEMENT, LOGIC, PILOTED 1

9 P30030 VALVE, SOLENOID 2

10 P30034 SPACER, E-COIL 2

11 P30031 NUT, COIL 2

12 P30033 E-COIL, 12 VDC 4

13 P30035 O-RING SEAL 2

14 P30026 ORIFICE, 0.090, 3/8-16 1

15 P30032 VALVE, RELIEF, 1000 PSI 1


Proof 9-4-14


Snow Blower

14

23

5 6

7

8

9

1210

11


Proof 9-4-14


Snow Blower (Cont’d)

ITEM PART NO. DESCRIPTIONSSB-51

QTY.SSB-60

QTY.SSB-84

QTY.

1 P10042 51” PLOW WELDMENT 1 - -

P30037 60” PLOW, WELDMENT - 1 -

P30001 84” PLOW, WELDMENT - - 1

2 P30043 KEY, SQUARE, IMPELLER MOTOR 1 1 1

3 P30017 HYDRAULIC MOTOR, IMPELLER 11.9 cu. in. 1 1 1

XXXXX HYDRAULIC MOTOR, IMPELLER 15.0 cu. in. (OPTION)

1 1 1

4 P30003 IMPELLER, WELDMENT 1 1 1

5 P50011-51 CUTTING EDGE, ULTRA 51” 1 - -

P50011-60 CUTTING EDGE, ULTRA 60” - 1 -

P50011-C CUTTING EDGE, ULTRA 84” - - 2

6 P30016 SKID SHOE, WELDMENT 2 2 2

7 P30013 NUT, SLOTTED, 1-1/4” 1 1 1

8 P30041 BOLT, 1/2” x 2” 4 4 4

9 P30044 LOCK NUT, 1/2” GRADE C 4 4 4

10 P60010 CARRIAGE BOLT, 5/8-11 x 2” 5 7 7

11 P60009 HEX NUT, 5/8-11 5 7 7

12 P30045 WASHER, 1-1/8” AS REG. AS REG. AS REG.

Not Shown P30046 COTTER PIN, 3/16 x 3” 1 1 1

Not Shown P30047 RETAINING PIN, 5/32 x 3” 2 2 2


Proof 9-4-14

Bruce

Sticky Note

Is there a part number for optional motors?



1

4

5

67

2

3

810

8

9

8

10

8

8

9


Proof 9-4-14



ITEM PART NO. DESCRIPTIONSSB-51

QTY.SSB-60

QTY.SSB-84

QTY.

1 P30048 AUGER SUPPORT (RH), WELDMENT 51” 1 - -

P30040 AUGER SUPPORT (RH), WELDMENT 60” - 1 -

P30007 AUGER SUPPORT (RH), WELDMENT 84” - - 1

2 P30049 AUGER SUPPORT (LH), WELDMENT 51” 1 - -

P30038 AUGER SUPPORT (LH), WELDMENT 60” - 1 -

P30004 AUGER SUPPORT (LH), WELDMENT 84” - - 1

3 P30014 BEARING, AUGER 1 1 1

4 P30050 AUGER 51”, WELDMENT 1 - -

P30039 AUGER 60”, WELDMENT - 1 -

P30006 AUGER 84”, WELDMENT - - 1

5 P30005 DRIVE PLUG, WELDMENT 1 1 1

6 P30018 HYDRAULIC MOTOR, AUGER 1 1 1

7 P30010 COVER, HYDRAULIC MOTOR, WELDMENT 1 1 1

8 P30041 BOLT, 1/2 x 2” 28 28 28

9 P30044 LOCK NUT, 1/2”, GRADE C 26 26 26

10 P30035 CARRIAGE BOLT, 5/8 x 3” 6 6 6

Not Shown 38050 HOSE, 3/4” x 104” 2 2 2

Not Shown 38015 HOSE, 3/4” x 22-1/2” 1 1 1

Not Shown 38025 HOSE, 3/4” x 23” 1 1 1

Not Shown 38010 HOSE, 3/4” x 19” 1 1 1

Not Shown 38020 HOSE, 3/4” x 24” 1 1 1

Not Shown 38035 HOSE, 1/4” x 84” 1 1 1

Not Shown 38030 HOSE, 1/4” x 80” 1 1 1

Not Shown 38035 HOSE, 1/4” x 53” 1 1 1

Not Shown 38047 HOSE,1/4” x 52” 1 1 1

Not Shown 38040 HOSE, 1/4” x 24” 1 1 1


Proof 9-4-14



1

2

3

4

56

8

7

12

11

10

10

9

9

12

13

13

9


Proof 9-4-14




1 P30009 PIN, DEFLECTOR HINGE, WELDMENT 1

2 P30008 DEFLECTOR, CHUTE, WELDMENT 1

3 P30002 CHUTE, WELDMENT - SMALL RING 1

P30002-1 CHUTE, WELDMENT - LARGE RING 1

P30002-2 CHUTE, WELDMENT - LARGE RING, 3 PIECE 1

4 P30012 COVER, BEARING BLOCK 3

5 P30011 BEARING, PLASTIC, CHUTE 6

6 P30020 VALVE BLOCK (SEE PAGE 44) 1

7 P30015 COVER, CHAIN 1

8 P30019 HYDRAULIC MOTOR, CHUTE 1

9 P30041 BOLT, 1/2 x 2” 6

10 P30052 BOLT, 3/4 x 4” 2

11 P30051 WASHER, 3/4” 2

12 P30053 LOCK NUT, 3/4”, GRADE C 2

13 P30044 LOCK NUT, 1/2”, GRADE C 4


Proof 9-4-14



8

2

6

5

9

7

3

4

10

11

12

1


1 P30060 HINGE PIN, 3/8 x 15-1/2” 1

2 P30061 HINGE PIN, 3/8 x 16-1/4” 1

3 P30062 LOWER CHUTE, WELDMENT 1

4 P30063 CHUTE LINK, WELDMENT 2

5 P30064 CENTER CHUTE, WELDMENT 1

6 P30065 UPPER CHUTE, WELDMENT 1

7 P30066 CHUTE CYLINDER, 6 x 1-1/4” 1

8 P30067 COTTER PIN, 1/8 x 3/4” 4

9 P60032 HEX BOLT, 3/8 x 1-1/2” 2

10 P30068 HEX BOLT, 3/8 x 2” 2

11 P30069 3/8” NYLOCK 4

12 P60036 3/8” WASHER 16


Proof 9-4-14

HYDRAULIC SCHEMATIC


Proof 9-4-14

Bruce

Sticky Note

Is there a hydraulic schematic.


Proof 9-4-14

WARRANTY


Proof 9-4-14


Proof 9-4-14

MANUFACTURER’S WARRANTY

SnowWolf Ultra Series Snow Blower

Two Year Limited Warranty

WolfGroup International, hereinafter referred to as WOLFGROUP, warrants new SNOWWOLF SNOW BLOWERS atthe time of delivery too the original purchaser, to be free from defects in material and workmanship when properly setup and operated in accordance with the recommendations set forth by WOLFGROUP.

WOLFGROUP’S liability for any defect with respect to accepted goods shall be limited to repairing the goods at aWOLFGROUP designated location or at an authorized dealer location, or replacing them as WOLFGROUP shallselect. The above shall be in accordance with WOLFGROUP warranty adjustment policies. WOLFGROUP’Sobligation shall terminate twenty-four (24) months after the delivery of the goods to original purchaser includingcutting edge breakage or wear. This warranty shall not apply to any machine or attachment which shall have beenrepaired or altered outside the WOLFGROUP factory or authorized WOLFGROUP dealership or in any way so as inWOLFGROUP’S judgment, to affect its stability or reliability, nor which has been subject to misuse, negligence oraccident beyond the company recommended machine rated capacity.

Warranty Claim

To submit a warranty claim, a return authorization from WOLFGROUP must be obtained. The failed part may then bereturned. Tampering with the failed part may void warranty. This warranty does not include freight or delivery chargesincurred when returning machinery for servicing. Dealer mileage, service calls, and pickup/delivery charges are thecustomer’s responsibility.

Exclusions of Warranty

Except as otherwise expressly stated herein, WOLFGROUP makes no representation or warranty of any kind,expressed or implied, AND MAKES NO WARRANTY OF MERCHANTABILITY IN RESPECT TO ITS MACHINERYAND/OR ATTACHMENTS ARE FIT FOR ANY PARTICULAR PURPOSE. WOLFGROUP shall not be liable forincidental or consequential damages for any breach or warranty, including but not limited to inconvenience, rental orreplacement equipment, loss of profits or other commercial loss. Upon purchase, the buyer assumes all liability for allpersonal injury and property resulting from handling, possession, or use of the goods by the buyer.

No agent, employee, or representative of WOLFGROUP has any authority to bind WOLFGROUP to any affirmation,representation or warranty concerning its machinery and/or attachments except as specifically set forth herein.

This warranty does not cover abuse or modifications made by others.

This warranty policy supersedes any previous documents.

No claims for warranty shall be considered unless warranty registration is sent to WolfGroup within 30 days ofpurchase.


Proof 9-4-14


Proof 9-4-14

snow blower om · 2019-05-20 · ultra snow blower owner’s manual 5 introduction owner...

Documents