solid works - tips&good practices - part 1
TRANSCRIPT
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 1/16
SOLIDWORKS TIPS / GOOD PRACTICE
Part - 1I.Karthik (30-04-2010)
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 2/16
3 D : Optimised part creation
- reduces the file size
Part-1 : Extrude (117Kb)
Part-1 : Revolve (109Kb)
2
Use features judiciously. Italways helps you to save thefile size.
Comes handy when dealingwith large assemblies
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 3/16
3 D : Grouping
S egregate the primary (revolve, extrude, cut-extrude etc..) and secondary
features (Fillet, chamfer) unless they have parent child dependency. This keepsyour feature tree clean and easy.
(211Kb)
(210Kb)
3
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 4/16
3 D : Part Creation - Orientation
Sketch plane = Front
Sketch plane = Top
The isometricorientation of thepart is realistic or close to reality
The isometricorientation of thepart looks odd
Applicable to assembly also «««. 4
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 5/16
3 D : Rapid sketch
3 D : Optimized feature usage (Depends on the part complexity)
(178Kb)
S ingle feature
(18 3 Kb)
Multiple feature¶s
Select plane
Select sketch tool
Sketch geometry Sketch geometry
5
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 6/16
3 D : Angle of projection
Four views
Window -> Viewport -> Four views 6
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 7/16
Select plane / Surface Position the hole
3D sketch
Select plane / Surface 2D sketch
3 D : While using the hole wizard
7
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 8/16
Sketch : Linear to Arc
A B
C
N ormal sketch
Retracing the origin ³B´ of the linesegment B-C invokes the arc.
A B
C
8
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 9/16
Sketch : 2D simulation
Create sketch Blocks
Blocks
Blocks
Mate Constraints Simulate
9
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 10/16
Sketch : Rectangle
W hile sketching a rectangle from the origin or considering any defined point as its center,
³Center Rectangle´ is preferred.This automatically constraints the diagonal of the rectangle with the center point
10
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 11/16
Sketch : Dimension increments
Input the minimum possibleincrement for a scroll
Modify the dimension through
scrolling
11
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 12/16
Sketch : Join using Trim !!!!
Trim tool can also be used to join two separatesketch entities.
Trim -> Trim to closet
The sketches getconnected andconstrained
12
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 13/16
Sketch : Creating the arc dimension
E ntities to select (Two end points of the arc and the arc itself : use ctrl key )
Pick the dimensioncommand and select theentities
13
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 14/16
Sketch : Fully defined
Automatically prompts theuser to constrain the sketchwhen he attempts to exit
Tools -> Options
14
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 15/16
Sketch : Dimension while creating
C ontinued in the next page
15
8/9/2019 Solid Works - Tips&Good Practices - part 1
http://slidepdf.com/reader/full/solid-works-tipsgood-practices-part-1 16/16
Sketch : Dimension while creating
Prompts the dimensional inputwhile sketching itself
16