sony nex 5 service manual level 1

5/28/2018 Sony NEX 5 Service Manual LEVEL 1

1/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L2Sony Corporation

SERVICE MANUAL

Revision History

SERVICE NOTE (Check the following note before the service.)

Ver. Date History ContentsS.M. Rev.

issued

LEVEL 2

985279731.pdf

2010E29-1

2010.5

Published by Sony Techno Create Corporation

Ver. 1.0 2010.05

INTERCHANGEABLE LENS DIGITAL CAMERAThe components identifiedby mark 0or dotted line withmark0are critical for safety.Replace only with part numberspecified.

Les composants identifis parune marque 0 sont critiquespour la scurit.Ne les remplacer que par unepice portant le numro spcifi.

US ModelCanadian Model

AEP ModelUK Model

E ModelAustralian Model

Chinese ModelKorea Model

Japanese ModelTourist Model

1-1. PRECAUTION ON REPLACING THE SY-258 BOARD1-2. PRECAUTION ON REPLACING THE CABINET FRONT

Official Release2010.051.0

9-852-797-31

NEX-3A/3D/3K/5A/5D/5K/5CKRMT-DSLR1

Photo: NEX-5/Black

[About the service of this model]

NEX-3A/5A is a commodity that packed the Interchangeable Lens Digital Camera (NEX-3/5) and Interchangeable Lens (E 16mm F2.8).

NEX-3D/5D is a commodity that packed the Interchangeable Lens Digital Camera (NEX-3/5) and Interchangeable Lens

(E 16mm F2.8 / E 18-55mm F3.5-5.6 OSS).

NEX-3K/5K/5CK is a commodity that packed the Interchangeable Lens Digital Camera (NEX-3/5/5C) and Interchangeable Lens

(E 18-55mm F3.5-5.6 OSS).

Refer to each following service manual of the Interchangeable Lens kit, when you repair.

Interchangeable Lens

SEL16F28 (E 16mm F2.8) Service Manual (9-852-798-1[])

SEL1855 (E 18-55mm F3.5-5.6 OSS) Service Manual (9-852-799-1[])

ENGLISH

JAPANESE

1-1. SY-2581-2.


2/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L2 2

SPECIFICATIONS

ENGLISH JAPANESE

E

23.4 15.6 mmAPS-CCMOS

14 600 00014 200 000

EV0 EV20ISO 100

F2.8

49

EV0 EV20ISO 100F2.8

ISOISO200 12800

2.0EV1/3

1/4000 301/3

1/160

7.5 cm3.0TFT

PRO SD

921 6006403RGB480

USBminiBHDMIHDMIC

NP-FW50

Exif PrintPRINT Image Matching III

NEX-5110.858.838.2 mmNEX-3117.262.633.4 mm

NEX-5287 gPRO

PRO

229 gNEX-3297 g

239 g040

JPEGDCFVer.2.0Exif Ver.2.3MPFBaselineDPOFNEX-5

AVCHDAVCHDVer.1.0MPEG-4 AVC/H.264Dolby Digital 2ch MP4MPEG-4 AVC/H.264MPEG-4 AAC-LC 2ch

NEX-3MPEG-4 Visual

USBHi-Speed USBUSB2.0

7ISO100m416mm

2.0EV1/335.923.842.7 mm

20.4 g

BC-VW1AC100 V - 240 V

50 Hz/60 Hz4.2 WDC 8.4 V0.28 A0402060639532 mm

85 g

NP-FW50DC 8.4 VDC 7.2V 7.7 Wh1 080 mAh

7.3 Wh1 020 mAh31.818.545 mm

57 g

BC-VW1 Battery chargerInputrating:100V 240 VAC,

50Hz/60Hz,4.2W

Outputrating:8.4 VDC, 0.28A

Operatingtemperaturerange: 0Cto

40C(32to104F)

Storagetemperature range:20C to

+60C(4Fto +140F)

Maximumdimensions:Approx.63

9532mm(21 /23 3 /41 5 /16

inches)(W/H/D)

Mass: Approx.85g (3oz)

Rechargeable battery packNP-FW50Usedbattery: Lithium-ion battery

Maximumvoltage:DC 8.4V

Nominalvoltage:DC 7.2V

Maximumchargevoltage:DC8.4VMaximumchargecurrent:1.02A

Capacity:Typical7.7Wh (1080mAh)

Minimum7.3Wh (1020mAh)

Maximumdimensions:

Approx.31.8 18.545 mm

(15/16 3/4 113/16inches)

(W/H/D)

Mass:Approx.57g (2.1oz)

Designandspecificationsare subject

to changewithout notice.

Camera

[System]

Cameratype: Interchangeable lens

digitalcamera

Lens:E-mount lens

[Image sensor]

Imagesensor:23.4 15.6mm(APS-C

format)CMOS imagesensor

Totalpixelnumberofimagesensor:

Approx.14600 000pixels

Effectivepixelnumberof camera:

Approx.14200 000pixels

[Anti-dust]

System:Charge protectioncoatingon

Low-PassFilter and

electromagneticvibration

mechanism

[Auto focus system]

System:Contrast detectionsystem

Sensitivityrange:0 EVto 20EV (at

ISO100 equivalent,with F2.8lens)

[Exposure control]

Meteringmethod:49-segment

meteringbythe imagesensor

Meteringrange:0 EVto20 EV(atISO

100equivalent,with F2.8lens)

ISO sensitivity(Recommended

exposureindex):Auto,ISO200to12800

Exposurecompensation:2.0EV (1/3

EVstep)

[Shutter]

Type:Electronically-controlled,

vertical-traverse,focal-plane type

Speedrange:1/4000secondto 30

seconds,BULB,(1/3EV step)

Flashsync speed:1/160 second

[Recording media]

MemoryStickPRODuomedia,

SDcard

[LCD monitor]

LCDpanel:7.5 cm(3.0type)TFT

driveTotalnumberofdots:921600(640 3

(RGB) 480)dots

[Input/output terminals]

USB:miniB

HDMI:HDMItypeC minijack

[Power]

Usedbattery pack:Rechargeable

batterypack NP-FW50

[Others]

ExifPrint: Compatible

PRINTImage MatchingIII:Compatible

Dimensions:

NEX-5/5C:

Approx.110.8 58.8 38.2mm

(43/82 3/81 9/16inches)

(W/H/D,excludingprotrusions)

NEX-3/3C:

Approx.117.2 62.6 33.4mm

(45/82 1/21 3/8inches)

(W/H/D,excludingprotrusions)

Mass:

NEX-5/5C:

Approx.287g (10.1oz)

(including batteryand Memory

StickPRO Duo media)

Approx.229g (8.1oz)

(cameraonly)

NEX-3/3C:

Approx.297g (10.5oz)

(including batteryand Memory

StickPRO Duo media)

Approx.239g (8.4oz)

(cameraonly)

Operatingtemperature:0C to40C

(32Fto 104F)

Fileformat:

Stillimage:JPEG(DCFVer.2.0,

ExifVer.2.3,MPFBaseline)

compliant,DPOF compatible

NEX-5/5C:

Movie(AVCHD format):

AVCHD Ver.1.0 compliant

Video:MPEG-4AVC/H.264

Audio:Dolby Digital2ch,

equippedwith DolbyDigital

StereoCreator

Manufacturedunderlicense

fromDolby Laboratories.

Movie(MP4 format):

Video:MPEG-4 AVC/H.264

Audio:MPEG-4 AAC-LC2ch

NEX-3/3C:

Movie:MPEG-4 Visual

USBcommunication:Hi-Speed USB

(USB2.0 compliant)

FlashFlashguidenumber:GN7 (inmetersat

ISO100)

Recyclingtime: Approx.4 seconds

Flashcoverage:Covering16mm lens

(focallength thatthe lensindicates)

Flashcompensation:2.0EV (1/3EV

step)

Dimensions:

Approx.35.9 23.8 42.7mm

(17/16 15/16 111/16inches)

(W/H/D,excludingprotrusions)Mass:Approx.20.4g(0.8oz)


3/33


Model information table

Abbreviation

AUS : Australian model

CH : Chinese model

CND : Canadian model

J : Japanese model

JE : Tourist model

KR : Korea model

Model NEX-3A NEX-3D NEX-3K

DestinationUS, CND, AEP, UK, E, KR,

J, JEAEP, UK, E, AUS, KR, J

US, CND, AEP, UK, E, AUS,

KR, J

Color system Auto (PAL/NTSC) Auto (PAL/NTSC) Auto (PAL/NTSC)

BT-060 flexible board


RL-101 flexible com-

plete board

RL-103 flexible com-plete board

FP-1236 flexible

board

FP-1246 flexible

board

Remote sensor

Eye-Fi Setup

Movie file format MPEG4 MPEG4 MPEG4

Lens E16 mm E18 55 mm/E16 mm E18 55 mm

Model NEX-5A NEX-5D NEX-5K NEX-5CK

DestinationAEP, UK, E,

AUS

US, CND, E,

KR, J

AEP, UK, E,

AUS, JE

CND, E,

KR, J

AEP, UK, E,

AUS

US, CND, E,

KR, JCH

Color system PAL NTSC PAL NTSC PAL NTSC PAL




plete board


plete board

FP-1236 flexible

board

FP-1246 flexible

board

Remote sensor

Eye-Fi Setup

Movie file formatAVCHD/

MPEG4

AVCHD/

MPEG4

AVCHD/

MPEG4

AVCHD/

MPEG4

AVCHD/

MPEG4

AVCHD/

MPEG4

AVCHD/

MPEG4

Lens E16 mm E16 mmE18 55

mm/E16 mm

E18 55

mm/E16 mmE18 55 mm E18 55 mm E18 55 mm


4/33


SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITHMARK0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LISTARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BYSONY.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!

LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONTCRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REM-PLACER CES COMPOSANTS QUE PAR DES PICES SONY DONTLES NUMROS SONT DONNS DANS CE MANUEL OU DANS LESSUPPLMENTS PUBLIS PAR SONY.

CautionDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.Dispose of used batteries according to the instructions.

Caution

CHEMICALS

Some chemicals used for servicing are highly volatile.

Their evaporation caused by improper management affects your health

and environment, and wastes resources.

Manage the chemicals carefully as follows.

Store chemicals sealed in a specific place to prevent from exposure

to high temperature or direct sunlight.

Avoid dividing chemicals into excessive numbers of small containers

to reduce natural evaporation.

Keep containers sealed to avoid natural evaporation when chemicals

are not in use. Avoid using chemicals as much as possible. When using chemicals,

divide only required amount to a small plate from the container and

use up it.

EXTERIOR PARTS

Be careful to the following points for plastic parts used in this unit.

Use a piece of cleaning paper or cleaning cloth for cleaning plastic

parts. Avoid using chemicals.

Even if you have to use chemicals to clean heavy dirt, dont use paint

thinner, ketone, nor alcohol.

Insert the specific screws vertically to the part when installing a

plastic part.

Be careful not to tighten screws too much.

UNLEADED SOLDER

This unit uses unleaded solder.

Boards requiring use of unleaded solder are printed with the lead free

mark (LF) indicating the solder contains no lead.

(Caution:Some printed circuit boards may not come printed with thelead free mark due to their particular size.)

: LEAD FREE MARKBe careful to the following points to solder or unsolder.

Set the soldering iron tip temperature to 350 C approximately.

If cannot control temperature, solder/unsolder at high temperature

for a short time.

Caution:The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!

Unleaded solder is more viscous (sticky, less prone to

flow) than ordinary solder so use caution not to let solder

bridges occur such as on IC pins, etc.

Be sure to control soldering iron tips used for unleaded solder and

those for leaded solder so they are managed separately. Mixing un-

leaded solder and leaded solder will cause detachment phenomenon.

SAFETY CHECK-OUT

After correcting the original service problem, perfor m the following

safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered

connections. Check the entire board surface for solder splashes and

bridges.

2. Check the interboard wiring to ensure that no wires are pinched

or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors,

that were installed during a previous repair. Point them out to the

customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs ofdeterioration. Point them out to the customer and recommend their

replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

K eep the temperature of the soldering iron around 270 C during

repairing.

Do not touch the soldering iron on the same conductor of the circuit

board (within 3 times).

B e careful not to apply force on the conductor when soldering or

unsoldering.

1.

2.

0

3.

4.

5.

6. 270 3

Lead F ree

350

IC

ENGLISH JAPANESE


5/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L21-1E

1. SERVICE NOTE

1-1. PRECAUTION ON REPLACING THE SY-258 BOARD

Destination Data

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.

USB Serial No.

The set is shipped with a unique ID (USB Serial No.) written in it.

This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.

ENGLISH JAPANESE

1-1. SY-258

USBNo.

1IDUSB Serial No.IDID

1-2.

3

: (1)(3)

(1) AssyIM (A, B, C)

(2) IMA

A

A+BB

(3) IME-Mount B(4) (5) IME-MountB

B BB IMB BB A+B BIM(6)

1-2. PRECAUTION ON REPLACING THE CABINET FRONT

Perform the following procedures for each of the three washers.

Note: Measure the dimensions before replacement of the Cabinet Front according to procedures (1) to (3).

(1) Remove the Imager Block Assy and the IM Adjust Washers (A, B, C).

(2) Measure the dimensions (A) of the removed IM Adjust Washers.

A

A+B

B

(3) Measure the distance (B) between the surface of the screw hole where the IM Adjust Washers were set and the surface of the E-Mount.(4) Replace Cabinet Front.

(5) Measure the distance after replacement of the Cabinet Front (B) between the surface of the screw hole where the IM Adjust Washers were set andthe surface of the E-Mount, then compare it with the distance before replacement (B).If the distance after replacement (B) is shorter than that before replacement (B)

Add IM Adjust Washer with the thickness equal to the difference of dimensions to make the distance (B) equal to that before replacement.If the distance after replacement (B) is longer than that before replacement (B)

Replace to the IM Adjust Washer with the thickness equal to the difference of dimensions

(distance before replacement (A+B) - distance after replacement (B)).(6) After assembly, take a test shot to check if there is any blur at circumference of the image.


6/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-1

2. REPAIR PARTS LIST

Follow the disassembly in the given numerical order.

(NEX-5A/5D/5K/5CK)

IDENTIFYING PARTS

Link ACCESSORIES

View Position

ASSEMBLY

Abbreviation


CH : Chinese model


J : Japanese model JE : Tourist model

KR : Korea model

(ENGLISH)

NOTE:

-XX, -X mean standardized parts, so they may have some differences from the original one. Items marked are not stocked since they are seldom required for routine service. Some delay

should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Due to standardization, replacements in the parts list may be different from the parts specified

in the diagrams or the components used on the set.

(JAPANESE)

-XX, -X, , ,

Color Indication of Appearance Parts

Example:

(SILVER) : Cabinets Color (Silver) : Parts Color

(SILVER) (Silver)

The components identified by mark 0ordotted line with mark0are critical for safety.Replace only with part number specified.

Les composants identifis par une marque0sont critiques pour la scurit.Ne les remplacer que par une pice portantle numro spcifi.

00

When indicating parts by reference number,

please include the board name.

Bottom View

Top View

Back View

Right View

Left View

Front View

THE COMBINATION OF CABINETS COLOR AND SCREW

(NEX-5A/5D/5K/5CK)The screw pointed is different according to the cabinet's color.For the combination of cabinet's color and screw, please refer to Table2-1.

Table 2-1

Screw's

Ref. No. (Parts Color.)

Cabinet's Color

#201 (Silver), #202 (Silver) SILVER

#196 (Black), #200 (Black) BLACK

9 Tripod Screwqs Cabinet Front Assy[Disassembly][Exploded View] Cabinet Front Section-1

Cabinet Front Section-2

6 BT Holder Block Assy BT-060 Flexible Board FP-1236 Flexible Board CN-439 Complete Board

qa MB Driving Unit

0 Imager Block Assy[Disassembly][Exploded View] IS-075 Flexible Board IS-076 Flexible Board

5 Jack Cover Base Assy

1 Cabinet (Rear) Block Assy

4 SY-258 Complete Board

2 Control Switch Block

3 Main Frame Block Assy[Disassembly][Exploded View] FP-1237 Flexible Complete Board

7 RL Button Block Assy

8 RL Block Assy

RL-101 Flexible Board


7/33NEX-3A/3D/3K/5A/5D/5K/5CK_L2

2-2

ENGLISH JAPANESE

NOTE FOR REPAIR

Make sure that the flat cable and flexible board are not cracked orbent at the terminal.

Do not insert the cable insufficiently nor crookedly.

When remove a connector, do not pull at wire of connector. It ispossible that a wire is snapped.

When installing a connector, do not press down at wire of connector.

It is possible that a wire is snapped.

Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt

which comes off at the point.(Be careful that somepieces of gilt may be left inside)


8/33NEX-3A/3D/3K/5A/5D/5K/5CK_L2

2-3

2-1. EXPLODED VIEWS

2-1-1. OVERALL SECTION

(NEX-5A/5D/5K/5CK)

ns: not supplied

Ref. No. P art No. Description Ref. No. Part No. Description

DISASSEMBLY

1 X-2547-947-2 LID ASSY (BLACK), BT (BLACK)

1 X-2547-948-2 LID ASSY (SILVER), BT (SILVER)

2 4-191-980-01 LABEL, MS

3 4-186-475-01 SPRING, BT LID OPEN (Note4)

4 X-2547-945-1 CABINET (REAR) ASSY (BRACK) (BLACK) (Note1, 2)

4 X-2547-946-1 CABINET (REAR) ASSY (SILVER) (SILVER) (Note1, 2)

5 4-186-478-01 GRIP (REAR), BLACK (BLACK)

5 4-186-478-11 GRIP (REAR), SILVER (SILVER)

6 4-186-479-01 SHEET, GRIP (REAR) ADHESIVE

7 4-186-476-01 SHAFT, BT LID

8 1-487-968-12 SWITCH BLOCK, CONTROL (BLACK)

8 1-487-968-22 SWITCH BLOCK, CONTROL (SILVER)

9 4-186-841-01 LABEL, VCCI/ JAPAN RECYCLE MARK (J)

#155 3-080-204-31 SCREW, TAPPING, P2

#196 4-178-124-01 SPECIAL (M1.4 (D2.75)) (BLACK) (Note3)


#201 4-178-124-21 SPECIAL (M1.4 (D2.75)) (SILVER) (Note3)


1 #200 / #202 X 4 USB Cover Open (1-1) #155 X 1 Shoe Cover Open (1-2)

#196 / #201 X 1 LCD Panel Open

1. Remove to numerical order (1to2) in the left figure.

Note

Note1: Perform the following procedures to remove Cabinet (Rear)Assy.

(1) Open LCD at the angle shown below.

(2) Raise the lower part of Cabinet (Rear) Assy, and slide itupward.

(3) Remove Cabinet (Rear) Assy while turning it in thedirection indicated by arrows.

Note3: Refer to THE COMBINATION OF CABINETS COLORAND SCREW (NEX-5A/5D/5K/5CK) on page 2-1 about the

combination of cabinets color and screw.

Right View Top ViewBottom ViewLeft View

#200#202

#200#202

#155

#196#201

Note1: Assy

1LCD

2Assy Assy

3Assy

Note2: Assemb ly-1: Method of attachment of Cabinet(Rear) Assy

Note2: Refer to Assembly-1: Method of attachment of Cabinet (Rear)Assy when you assemble.

Note3: 2 - 1 THE COMB INAT ION OF CABI NETS COLOR AND S CREW

(NEX-5A/5D /5K/5CK)

Screw

Note4: Refer to Assembly-6: Method of attachment of BT Lid Assywhen you assemble.

Note4: Assembly-6 : Method of attachment of BT Lid Assy

1.7

6.0

#155:M1.7 X 6.0 (Tapping)

(Black)3-080-204-31

#196: M1.4 X 2.0

(Black)

4-178-124-01

2.0

1.4

#200: M1.4 X 3.8

(Black)

4-178-124-11

3.8

1.4

#202: M1.4 X 3.8

(Silver)

4-178-124-31

3.8

1.4

#201: M1.4 X 2.0

(Silver)

4-178-124-21

2.0

1.4

LCD Section(See Page 2-4)

(Note3)#196#201

#155

#200#202(Note3)

5

3(Note4)

1

6

7

2(Claw)

2 8

1 4(Note1, 2)

ns

2

1-1

1-2

1(Claw)

#200#202(Note3)

9


9/33NEX-3A/3D/3K/5A/5D/5K/5CK_L2

2-4

2-1-2. LCD SECTION

(NEX-5A/5D/5K/5CK)

Ref. No. P art No. Description Ref. No. Part No. Description

DISASSEMBLY

51 4-186-569-01 INSULATING SHEET, LC FLEXIBLE (Note5, 6, 7)

52 X-2547-951-1 CABINET (REAR) ASSY, LC

53 1-471-549-11 MAGNET (ND7.9X2.9X1.2)

54 4-186-568-01 INSULATING SHEET, LC CONNECTOR (Note6)

55 4-186-563-01 RETAINER, LC FLEXIBLE

56 A-1773-793-A FP-1237 FLEXIBLE BOARD, COMPLETE

57 4-186-555-01 LIGHT (LC), GUIDE,

58 4-186-572-02 INSULATING SHEET A (SY) (Note3)

59 X-2547-950-1 PIN ASSY, S LOCK

60 4-186-566-01 BASE (L), STRAP (BLACK)

60 4-186-566-11 BASE (L), STRAP (SILVER)

#27 2-662-396-11 SCREW (M1.4), NEW, TRUSTAR, P2

#187 3-234-449-05 SCREW (M1.4)



3 #187 X 2 #196 / #201 X 2 LC Cabinet (Rear) Assy (3-1) #187 X 2 LC Flexible Retainer (3-2) Release LCD Flexible Board (3-3) Peel off LC Flexible Insulating Sheet (3-4) #27 X 5 Strap Base (L) (3-5) S Lock Pin Assy (3-6)

1. Remove to numerical order (3) in the left figure.

Note

Note4: Refer to THE COMBINATION OF CABINETS COLORAND SCREW (NEX-5A/5D/5K/5CK) on page 2-1 about thecombination of cabinets color and screw.

Note1: To remove Frame Assy, firstly remove LCD Flexible Boardand LC Flexible Insulating Sheet, then unfix FP-1237 FlexibleComplete Board.

Note2: Refer to Assembly-2: Temporally secure FP-1237 FlexibleComplete Board when you assemble.

Note1: ASSYLCDLCFP-1237

Note2: Assembly-2: Temporally secu re FP-1237 FlexibleComplete Board

Note3: Refer to Assembly- 3: Insulating Sheet A (SY) puttingposition when you assemble.

Note3: Assembl y-3: Insulating Sheet A (SY) putting posi-tion

Note4: 2 - 1 THE COMB INATI ON OF CABIN ETS COLOR AND S CREW(NEX-5A/5D /5K/5CK)

Note5: Refer to Assembly-4: LC Flexible Insulating Sheet puttingposition when you assemble.

Note5: Assembly-4: LC Flexible Insulating S heet puttingposition

Note6: Refer to Assembl y-5: LC Connect or Insulating Sheet,LC Flexible Insulating Sheet putting position when youassemble.

Note6: Assembly- 5: LC Connector Insulating Shee t, LC Flex-ible Insulating She et putting position

Screw



Top View

#27

Bottom View

#196#201

#27

#187

LCD Back

3 Main Frame Section(See Page 2-10)(Note1, 2)

Main Board Section(See Page 2-5)

#196#201(Note4)

#27

#27

52

3-1

58(Note3)

57

3-659

3-560

51

3-4(Note5)

53#187

#187

3-3

56

54(Note6)

51(Note6)

51(Note7)

#27

55

3-2

SY-258

#27:M1.4 X 2.0(Black)

2-662-396-11

2.0

1.4

1.4

1.4

#187:M1.4 X 1.4

(Silver)

3-234-449-05

#196: M1.4 X 2.0

(Black)

4-178-124-01

2.0

1.4

#201: M1.4 X 2.0

(Silver)

4-178-124-21

2.0

1.4


10/33NEX-3A/3D/3K/5A/5D/5K/5CK_L2

2-5

Ref. No. Part No. Description Ref. No. P art No. Description

2-1-3. MAIN BOARD SECTION

(NEX-5A/5D/5K/5CK)DISASSEMBLY

101 4-186-559-01 GROUND PLATE (L), BOTTOM

102 4-186-561-01 GROUND PLATE (L), TOP

103 4-186-560-01 GROUND PLATE (G), BOTTOM

104 4-186-573-01 INSULATING SHEET B (SY) (Note1)

105 A-1782-475-A SY-258 BOARD, COMPLETE (SERVICE)

106 4-187-240-01 SHEET (SY), RADIATION

MIC902 1-542-757-61 MICROPHONE UNIT (Note2)

#71 3-208-537-01 0+Z M1.4X2 NEW TORASUTA

#192 4-188-736-01 SCREW (TP1.4), P2


4 #192 X 3 #71 X 1

Note

Screw

Note1: Refer to Assembly-10: Insulating Sheet B (SY) puttingposition when you assemble.

Note1: Assembly-1 0: Insulating Sheet B (SY) putting posi-tion

Note2: Refer to Assembly-11: Routing of Microphone Harnesswhen you assemble.

Note2: Assemb ly-11: Routi ng of Microphone Harnes s

B

A

AA

Solder

#71

#192

104(Note1)

106

101

103

102

BT / RL Section(See Page 2-6)

MIC902(Note2)

4 105

B

SY-25

8

#192

Back View

#192

#71

#71:M1.4 X 2.0(Red)

3-208-537-01

2.0

1.4

#192: M1.4 X 4.0 (Tapping)

(Black)

4-188-736-01

4.0

1.4


11/33NEX-3A/3D/3K/5A/5D/5K/5CK_L2

2-6

Ref. No. Part No. Description Ref. No. Part No. Description

DISASSEMBLY

151 4-186-554-01 COVER, HDMI (BLACK)

151 4-186-554-11 COVER, HDMI (SILVER)

152 4-186-553-01 COVER, USB (BLACK)

152 4-186-553-11 COVER, USB (SILVER) 153 4-186-557-01 COVER, SHOE (BLACK)

153 4-186-557-11 COVER, SHOE (SILVER)

154 4-186-551-02 BASE, JACK COVER (BLACK) (Note6)

154 4-186-551-12 BASE, JACK COVER (SILVER) (Note6)

155 4-186-446-01 LIGHT (MS), GUIDE,

156 4-186-444-01 BASE, BT LID

157 A-1782-438-A RL BLOCK ASSY (SERVICE) (Note5)

158 4-186-473-01 HOLDER, SP

159 4-186-556-01 SCREW, TRIPOD

160 A-1782-432-A CABINET FRONT BLOCK ASSY (SERVICE) (BLACK)

(including CP001 (CMOS imager) and IS-077 complete board) (Note7, 9)

160 A-1782-433-A CABINET FRONT BLOCK ASSY (SERVICE) (SILVER)


161 A-1774-556-A BUTTON BLOCK ASSY, RL

162 1-880-965-11 BT-060 FLEXIBLE BOARD

163 X-2547-936-1 BT FRAME ASSY (Note2)

164 4-186-448-01 GASKET (MS) (Note1)

165 A-1773-791-A CN-439 BOARD, COMPLETE

166 4-186-449-01 SHEET (CN FPC)

167 1-880-967-11 FP-1236 FLEXIBLE BOARD

168 4-186-447-01 INSULATING SHEET (MS)


0BT900 1-756-813-11 LITHIUM RECHARGEABLE BATTERY(Note4)

0BT901 1-780-858-11 TERMINAL BOARD BATTERY



#71 3-208-537-01 0+Z M1.4X2 NEW TORASUTA

#191 4-188-735-01 SCREW (M1.7)

#192 4-188-736-01 SCREW (TP1.4), P2




6 #191 X 2

Note

2-1-4. BT / RL SECTION

(NEX-5A/5D/5K/5CK)

#191

Back View

Screw

7 #192 X 1

#192

Bottom View

8 #27 X 1 #191 X 1

Back View#27 #191

9 #200 / #202 X 1

Note1: Refer to Assembly-12: Inserting Gasket (MS) (NEX-5A/5D/5K/5CK) when you assemble.

Note1: Assembly-1 2: Inserting Gasket (MS)(NEX-5A/5D /5K/5CK)

Note2: Refer to Assembly-13: Assemble BT Holder Block Assy(NEX-5A/5D/5K/5CK) when you assemble.

Note2: Assembly-1 3: Assemble BT Holder Block Assy (NEX-5A/5D/5K/ 5CK)

Note3: Refer to Assembly-14: Routing of Microphone Harness(NEX-5A/5D/5K/5CK) when you assemble.

Note3: Assem bly-14: Routing of Micro phone Harness(NEX-5A/5D /5K/5CK)

Note4: Refer to Assembly-15: Lithium Rechargeable Battery puttingposition when you assemble.

Note4: Assembly-1 5: Lithium Rechargeable Batteryputting position

Note5: Refer to Assembly-16: Note when assembling RL Block Assy(NEX-5A/5D/5K/5CK) when you assemble.

Note5: Assembly-1 6: Note when assembling RL Block Assy(NEX-5A/5D /5K/5CK)

Note6: Refer to Assembly-19: Note on Alignment of the FlexibleBoard when assembling Jack Cover Base(NEX-5A/5D/5K/5CK) when you assemble.

Note6: Assembly-1 9: Note on Alignment of the FlexibleBoard when assembling Jack Cover Base(NEX-5A/5D /5K/5CK)

Note7:Precautions for Replacement of Cabinet Front Block Assy (Service)As Cabinet Front Block Assy (Service) may be damaged by staticelectricity from its structure, handle it carefully like for the MOS IC.In addition, ensure that the receiver is not covered with dusts norexposed to strong light.

Solder

Solder

Imager Block Section(See Page 2-7)(including CP001 (CMOS imager) and IS-077 complete board)

160(Note7, 9)

7 161

162

6 163(Note2)164(Note1)

165

166

#71#191

168

167

#200#202(Note8)

#27

#192

#191

MIC901 (Note3)

BT900 (Note4)

BT901

158

8 157(Note5) 156

155153

5 154(Note6)

152

151

9 159

CN-439

169(Note10)

: BT900 (LITHIUM RECHARGEABLE BATTERY)Board on the mount position.(See page Level3 6-35)

Bottom View

#200#202



#27:M1.4 X 2.0(Black)

2-662-396-11

2.0

1.4

(Red)3-208-537-01

2.0

1.4

#191: M1.7 X 3.5 (Tapping)(Black)4-188-735-01

3.5

1.7

#192: M1.4 X 4.0 (Tapping)(Black)4-188-736-01

4.0

1.4

#200: M1.4 X 3.8(Black)4-178-124-11

3.8

1.4

#71:M1.4 X 2.0 #202: M1.4 X 3.8(Silver)4-178-124-31

3.8

1.4

Note7:Assy

AssyMOS IC

Note9: Refer to PRECAUTION ON REPLACING THE CABINETFRONT on page 1-1 when replacing Cabinet Front Block Assy(Service).

Note9: Assy1 - 1 PRECA UTION ON RE PLACIN G THE CAB INET FR ONT

Note10:Refer to Assembly- 33: LC Connector Insulati ng Sheetputting position when you assemble.

Note10: Assembl y-33: LC Connec tor Insula ting Sheet put -ting position

CautionDanger of explosion occurs if battery is incorrectly replaced. Replace onlywith the same or equivalent type.Dispose of used batteries accordingto the instructions.

Caution


12/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-7


2-1-5. IMAGER BLOCK SECTION

(NEX-5A/5D/5K/5CK)DISASSEMBLY

0201 A-1773-803-A MB CHARGE UNIT

0202 1-487-619-11 SHUTTER UNIT (H094)

203 Selection Parts IM WASHER (C), ADJUST (Note1, 2)

204 Selection Parts IM WASHER (B), ADJUST (Note1, 2)

205 Selection Parts IM WASHER (A), ADJUST (Note1, 2)

206 4-185-968-02 MB TAPE, MASK SHEET (Note3)

207 4-185-966-01 MB SHEET, MASK (Note3)


#191 4-188-735-01 SCREW (M1.7)

#197 4-185-990-01 MB SCREW, CHARGE UNIT FIXED

1. Remove to numerical order (0to qs) in the left figure.

0 #191 X 3

Note

qa #27 X 1 #191 X 1

Screw

Back View

#191

Back View

#191

#27

Note2: Refer to Assembly-23: IM Adjust Washer (A, B, C) puttingposition when you assemble.

Note2: Assembly-23: IM Adjust Washer (A, B, C ) puttingposition

Note3: Refer to Assembly-24: Method of attachment of MB MaskSheet when you assemble.

Note3: Assemb ly-24: Method of attachment of MB MaskShee t

206(Note3)qs Cabinet Front Section-1

(See Page 2-8)

Claw

Claw

#197

202

qa 201 #191

0Imager Unit Section(See Page 2-11) #191

203(Note1, 2)

204(Note1, 2)

205(Note1, 2)

#27

207(Note3)

#27:M1.4 X 2.0

(Black)2-662-396-11

2.0

1.4

#191: M1.7 X 3.5 (Tapping)

(Black)

4-188-735-01

3.5

1.7

#197: M1.6 X 4.5 (Tapping)

(Silver)

4-185-990-01

4.5

1.6

Note1: The type of these parts should be selected when performingadjustments.

Refer to "2-3. SELECTION PARTS" on page 2-23 .

Note1: 2 - 2 32-3. S ELECTION PARTS


13/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-8

Ref. No. P art No. Description Ref. No. P art No. Description

2-1-6. CABINET FRONT SECTION - 1

(NEX-5A/5D/5K/5CK)

251 4-186-540-01 SHEET (FRONT), BT SLIDER (Note1)

252 4-186-541-01 SHEET (HORIZONTAL), BT SLIDER (Note2)

253 4-186-523-01 WINDOW (AF)

254 4-186-525-01 BASE (FRONT), PW KNOB

255 4-186-527-01 SHEET, PW RING ADHESIVE

256 4-186-528-01 RING, PW ORNAMENTAL (BLACK)

256 4-186-528-11 RING, PW ORNAMENTAL (SILVER)

257 4-186-530-01 KNOB, PW (BLACK)

257 4-186-530-11 KNOB, PW (SILVER)

258 4-186-526-01 BASE (REAR), PW KNOB

259 4-186-537-01 SPRING, PW KNOB

260 4-186-524-01 RETAINER, PW KNOB

261 4-196-544-01 TAPE (AS (210)) (Note3)

#155 3-080-204-31 SCREW, TAPPING, P2

Note

Screw

Note1: Refer to Assembly-25: BT Slider Sheet (front) puttingposition (NEX-5A/5D/5K/5CK) when you assemble.

Note1: Assembly- 25: BT Slider Sheet (front) putti ng position(NEX-5A/5D/5K/5CK)

Note2: Refer to Assembly-26: BT Slider Sheet (horizontal) puttingposition (NEX-5A/5D/5K/5CK) when you assemble.

Note2: Assemb ly-26: BT Slider Sheet (horizonta l) puttingposition (NEX-5A /5D/5K/5C K)

#155

257

256

255

254

253

258

252(Note2)

251(Note1)

259

260

Cabinet Front Section-2(See Page 2-9)

261(Note3)

1.7

6.0

#155:M1.7 X 6.0 (Tapping)

(Black)

3-080-204-31

Note3: Refer to Assembly-34: Tape AS (210) putting position (NEX-5A/5D/5K/5CK) when you assemble.

Note3: Assembly-3 4: Tape AS (210) putting position (NEX-5A/5D/5K/ 5CK)


14/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-9


301 4-185-964-03 MB N PLATE (A)

302 4-185-962-01 MB N PLATE (B)

303 4-185-963-01 MB N PLATE SP (Note1)

304 4-186-539-01 RING, ORNAMENTAL

305 4-186-534-01 BUTTON, L LOCK (BLACK)

305 4-186-534-11 BUTTON, L LOCK (SILVER)

306 X-2547-937-1 PIN ASSY, L LOCK

307 4-186-538-01 SPRING, LENS LOCK

308 4-186-536-01 HOLDER, L LOCK

309 4-186-521-01 GRIP (BLACK)

309 4-186-521-11 GRIP (SILVER)

310 4-186-519-01 WINDOW (IR)

311 4-186-542-01 SHEET, GRIP ADHESIVE

312 4-186-517-01 CABINET (FRONT) (BLACK) (Note3)

312 4-186-517-11 CABINET (FRONT) (SILVER) (Note3)

313 4-186-532-01 COVER, ORNAMENTAL RING (BLACK)

313 4-186-532-11 COVER, ORNAMENTAL RING (SILVER)

314 X-2547-938-1 PLATE ASSY, SHOE NUT

315 4-186-543-01 PLATE, LOGO (BLACK)

315 4-186-543-11 PLATE, LOGO (SILVER)

316 A-1773-802-A MB CONTACT UNIT, N (Note2, 4)

#23 3-080-204-11 SCREW, TAPPING, P2


#191 4-188-735-01 SCREW (M1.7)

#195 3-197-324-01 M1.7X2.5X3GF (D4X0.5)

#198 4-186-545-01 M1.7X4 SPIN

Note

2-1-7. CABINET FRONT SECTION - 2

(NEX-5A/5D/5K/5CK)

ns: not supplied

Screw

Note1: Refer to Assembly- 27: Apply grease on MB N Plate SPwhen you assemble.

Note1: Assembly-2 7: Apply greas e on MB N Plate SP

Note2: Refer to Assembly-28: MB N Contact Unit holding positionwhen you assemble.

Note2: Assembly-2 8: MB N Contact Unit holding position

303(Note1)

#198

ns

#195

#191

#27#23

302

304

301

307

306

308

305

315

309

310

311 312(Note3)

313

314

316(Note2, 4)

#23:M1.7 X 4.0 (Tapping)

(Black)

3-080-204-11

4.0

1.7

#27:M1.4 X 2.0

(Black)

2-662-396-11

2.0

1.4

#191: M1.7 X 3.5 (Tapping)

(Black)

4-188-735-01

3.5

1.7

2.5

1.7

#195: M1.7 X 2.5

(Silver)

3-197-324-01

4.0

1.7

#198: M1.7 X 4.0

(Silver)

4-186-545-01

Note3: Refer to PRECAUTION ON REPLACING THE CABINETFRONT on page 1-1 when replacing Cabinet (Front).

Note3: 1 - 1 PRECAUTI ONON REPLACING THE C ABINET FRON T

Note4: Refer to PRECAUTION ON REPLACING THE CABINETFRONT on page 1-1 when replacing MB N Contact Unit.

Note4: MB N 1 - 1 PRECAUTION ON REPLACING THE CABINET FRONT


15/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-10


351 4-186-425-01 BRACKET (L), STRAP

352 4-195-258-01 SHAFT, CUSHION (MF) (Note1)

353 4-186-571-01 SHEET, LC LIGHT INTERCEPTION

0354 A-1774-560-A PANEL BLOCK ASSY (BLACK)

0354 A-1774-561-A PANEL BLOCK ASSY (SILVER)

355 4-186-424-01 BRACKET (G), STRAP

356 4-186-565-01 BASE (G), STRAP (BLACK)

356 4-186-565-11 BASE (G), STRAP (SILVER)

357 4-186-438-01 PLATE, BT LOCK

358 4-186-437-01 CLAW, BT LOCK

359 X-2547-935-1 FRAME ASSY

#79 2-587-151-11 SCREW (M1.4), NEW TRUSTAR.P2

#187 3-234-449-05 SCREW (M1.4)

#192 4-188-736-01 SCREW (TP1.4), P2



Note

Note1: Refer to Assembly-8: Shaft Cushion (MF) putting positionwhen you assemble.

Note1: Assembly- 8: Shaft Cushion (MF) putting position

Screw2-1-8. MAIN FRAME SECTION

(NEX-5A/5D/5K/5CK)

ns: not supplied

#196#201(Note2)

#79

#187

#192

#79

354

356

355

357

358

353

352(Note1)

351

ns

359



2.0

1.4

#79:M1.4X 2.0

(Silver)

2-587-151-11

1.4

1.4

#187:M1.4 X 1.4

(Silver)

3-234-449-05

#196: M1.4 X 2.0

(Black)

4-178-124-01

2.0

1.4

#201: M1.4 X 2.0

(Silver)

4-178-124-21

2.0

1.4

#192: M1.4 X 4.0 (Tapping)

(Black)

4-188-736-01

4.0

1.4


16/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-11


401 4-185-996-01 IM PLATE, IMAGER

402 A-1773-805-A IM PLATE UNIT, LOWPASS RETAINER

403 1-856-102-11 OPTICAL FILTER BLOCK (OFB-01-09) (Note1, 4)

404 4-193-875-01 CUTTER, IM FLARE (S)

405 4-185-993-01 IM SHEET, SPACER

406 4-194-127-01 IM TAPE, SPACER FIXED (S)

407 4-186-454-01 RADIATION SHEET (IS) (Note3)

408 4-186-455-01 HEAT SINK (Note2)

409 1-880-963-11 IS-075 FLEXIBLE BOARD



#191 4-188-735-01 SCREW (M1.7)

Note

2-1-9. IMAGER UNIT SECTION

(NEX-5A/5D/5K/5CK)

ns: not supplied

Screw

#27:M1.4 X 2.0(Black)

2-662-396-11

2.0

1.4

#191: M1.7 X 3.5 (Tapping)

(Black)

4-188-735-01

3.5

1.7

#27

#191

ns

#27

401

402

405

406

410

407(Note3)

409

403(Note1, 4)

404

408(Note2)

Note2: Refer to Assembly-29: Note when assembling Heat Sinkwhen you assemble.

Note2: Assembly-2 9: Note when ass embling Heat Sink

Note3: Refer to Assembly-31: Radiation Sheet (IS) putting positionwhen you assemble.

Note3: Assembly-31: Radiatio n Sheet (IS) putting position

Note4: Refer to 3-2. CLEANING PROCEDURE OF OLPF on page3-5 for method of cleaning the OLPF.

Note4: OL PF3-5 3-2. CLEA NING PROCEDUREOF OLPF

Note1: Refer to the following statements when replacing the Opticalfilter block.

Method of Removal (1) Pour resolvent (alcohol or cleaning agent) between the

imager and the IM spacer sheet. Wait for that the adhesive power of the IM spacer fixed

tape weakens. (2) Remove the IM spacer sheet from the imager.

Pour resolvent (alcohol or cleaning agent)

between the imager and the IM s pacer sheet.

Method of Attachment (1) Attach the IM flare cutter and the Optical filter block by

aligning them with the outer shape of the IM spacer sheetevenly.

The two-layer side of the Optical filter block is on theimager side.

(2) Attach the IM spacer fixed tape by aligning it with theouter shape of the IM spacer sheet evenly.

The two-layerside is on theimager side.

Mount

Side

Imager

Side

Optical Filter Block

Peel off thereleased paper.



IM Flare Cutter

IM Spacer Sheet

IM Spacer

Fixed Tape

(3) Set the Optical filter block in its attachment jig(J-6082-737-A), with the attached IM spacer fixed tapefacing upward.

(4) Press the imager down into the jig as shown below toattach it to the Optical filter block.

J-6082-737-A

Imager

Peel off the released paper.

Note1:

(1) IM( ) IM (2) IM

IM

()

(1) IMIM 2 (2) IMIM

2

IM

IM

IM

(3) IM (J-6082-737-A) (4)

J-6082-737-A


17/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-12

Follow the disassembly in the given numerical order.

(NEX-3A/3D/3K)

IDENTIFYING PARTS

Link ACCESSORIES

View Position

ASSEMBLY

Abbreviation


CH : Chinese model


J : Japanese model

JE : Tourist model

KR : Korea model

(ENGLISH)

NOTE:

-XX, -X mean standardized parts, so they may have some differences from the original one. Items marked are not stocked since they are seldom required for routine service. Some delay

should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Due to standardization, replacements in the parts list may be different from the parts specified

in the diagrams or the components used on the set.

(JAPANESE)

-XX, -X, , ,

Color Indication of Appearance Parts

Example:

(SILVER) : Cabinets Color

(Silver) : Parts Color

(SILVER) (Silver)

The components identified by mark 0ordotted line with mark0are critical for safety.Replace only with part number specified.

Les composants identifis par une marque0sont critiques pour la scurit.Ne les remplacer que par une pice portantle numro spcifi.

00

When indicating parts by reference number,

please include the board name.

THE COMBINATION OF CABINETS COLOR AND SCREW

(NEX-3A/3D/3K)The screw pointed is different according to the cabinet's color.For the combination of cabinet's color and screw, please refer to Table2-2.

Table 2-2

Screw'sRef. No. (Parts Color.)

Cabinet's Color

#10 (Silver), #201 (Silver) SILVER, WHITE

#2 (Black), #196 (Black) BLACK, RED

qd Cabinet Front Assy

[Disassembly][Exploded View]

qs MB Driving Unit

qa Imager Block Assy[Disassembly][Exploded View] IS-075 Flexible Board IS-076 Flexible Board

7 SY Holder Assy[Disassembly][Exploded View]

1 Cabinet (Rear) Assy

4 Side Cover

9 BT Holder Block Assy BT-063 Flexible Board

6 CN-439 Complete Board FP-1246 Flexible Board

5 SY-258 Complete Board

2 Control Switch Block

3 Main Frame Block Assy[Disassembly][Exploded View] FP-1237 Flexible Complete Board

8 Cabinet (Upper) Block Assy

RL-103 Flexible Board

0 Tripod Screw

Bottom View

Top View

Back View

Right View

Left View

Front View


18/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-13

ENGLISH JAPANESE

NOTE FOR REPAIR

Make sure that the flat cable and flexible board are not cracked orbent at the terminal.

Do not insert the cable insufficiently nor crookedly.

When remove a connector, do not pull at wire of connector. It ispossible that a wire is snapped.

When installing a connector, do not press down at wire of connector.

It is possible that a wire is snapped.

Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt

which comes off at the point.(Be careful that somepieces of gilt may be left inside)


19/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-14


2-2. EXPLODED VIEWS

2-2-1. OVERALL SECTION

(NEX-3A/3D/3K)

ns: not supplied

DISASSEMBLY

1 X-2548-254-1 CABINET (REAR) ASSY (210B) (BLACK) (Note1, 2, 5, 6)

1 X-2548-255-1 CABINET (REAR) ASSY (210S) (SILVER) (Note1, 2, 5, 6)

1 X-2548-256-1 CABINET (REAR) ASSY (210R) (RED) (Note1, 2, 5, 6)

1 X-2548-257-1 CABINET (REAR) ASSY (210W) (WHITE) (Note1, 2, 5, 6)

2 4-190-793-01 GRIP (210), (REAR) (BLACK)

2 4-190-793-11 GRIP (210), (REAR) (SILVER)

2 4-190-793-21 GRIP (210), (REAR) (RED)

2 4-190-793-31 GRIP (210), (REAR) (WHITE)

3 4-190-794-01 SHEET (210), REAR GRIP ADHESIVE

4 1-487-968-12 SWITCH BLOCK, CONTROL (BLACK)

4 1-487-968-22 SWITCH BLOCK, CONTROL (SILVER)

4 1-487-968-31 SWITCH BLOCK, CONTROL (RED)

4 1-487-968-41 SWITCH BLOCK, CONTROL (WHITE)

#2 2-635-562-31 SCREW (M1.7) (RED, BLACK) (Note3, 4)

#10 2-599-475-31 SCREW (M1.7) (SILVER, WHITE) (Note3, 4)


Note

Screw

1 #2 / #10 X 6 BT Lid Open (1-1) #2 / #10 X 1 Shoe Cover Open (1-2) #2 / #10 X 4

USB Cover Open (1-3) #2 / #10 X 1 LCD Panel Open

Note2: Assemb ly-1: Method of attachment of Cabinet(Rear) Assy

Note2: Refer to Assembly-1: Method of attachment of Cabinet (Rear)Assy when you assemble.

Note3: Refer to THE COMBINATION OF CABINETS COLORAND SCREW (NEX- 3A/3D/ 3K) on p age 2-12 about thecombination of cabinets color and screw.

Note3: 2 - 12 THE COMB INATI ON OF CABIN ETS COLOR AND S CREW(NEX-3A/3D /3K)

#2#10

#2#10

#2#10

Bottom ViewLeft View Right ViewTop View

#2#10

#2#10

Note5: When assembling or disassembling, keep Power Knob in aposition between ON and OFF.

Power Knob

OF F ON

Note5: PWON OFF

PW

OF F O N

#10:M1.7 X 4.0

(Silver)

2-599-475-31

#2: M1.7 X 4.0

(Black)

2-635-562-31

4.0

1.7

4.0

1.7

#2#10(Note3)

#2#10(Note3, 4)

#2#10(Note3, 4)

#2#10(Note3, 4)

#2#10(Note3, 4)

#2#10(Note3, 4)

#2#10(Note3, 4)

#2#10 (Note3, 4)

3

2

2 4

ns

LCD Section(See Page 2-15)

2(Claw)

1 1(Note1, 2, 5, 6)

1-3

1-1

1-2

Note1: Assy

1LCD

2Assy Assy

3Assy

Note1: Perform the following procedures to remove Cabinet (Rear)Assy.

(1) Open LCD at the angle shown below.

(2) Raise the lower part of Cabinet (Rear) Assy, and slide itupward.

(3) Remove Cabinet (Rear) Assy while turning it in thedirection indicated by arrows.

Note4: Refer to Assembly-7: Screw tightening sequence whenassembling the exterior parts (NEX-3A/3D/3K) when youassemble.

Note4: Assem bly-7: Screw tightening sequen ce whenassembling the exter ior parts (NEX-3A /3D/3K)

Note6: When assembling or disassembling, loosen the two screwsas shown below.

#2/#10#192

Note6: 2

#2/#10#192


20/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-15


2-2-2. LCD SECTION

(NEX-3A/3D/3K)DISASSEMBLY


52 1-471-549-11 MAGNET (ND7.9X2.9X1.2)

53 4-186-569-01 INSULATING SHEET, LC FLEXIBLE (Note5, 6, 7)

54 X-2547-951-1 CABINET (REAR) ASSY, LC

55 4-186-563-01 RETAINER, LC FLEXIBLE

56 A-1773-793-A FP-1237 FLEXIBLE BOARD, COMPLETE

57 4-186-572-02 INSULATING SHEET A (SY) (Note3)

58 4-190-960-01 BASE (G) (210), STRAP (BLACK)

58 4-190-960-11 BASE (G) (210), STRAP (SILVER)

58 4-190-960-21 BASE (G) (210), STRAP (RED)

58 4-190-960-31 BASE (G) (210), STRAP (WHITE)

#2 2-635-562-31 SCREW (M1.7) (RED, BLACK) (Note4)

#10 2-599-475-31 SCREW (M1.7) (SILVER, WHITE) (Note4)

#187 3-234-449-05 SCREW (M1.4)

#196 4-178-124-01 SPECIAL (M1.4 (D2.75)) (RED, BLACK) (Note4)

#201 4-178-124-21 SPECIAL (M1.4 (D2.75)) (SILVER, WHITE) (Note4)


Note

3 #187 X 2 #196 / #201 X 2 LC Cabinet (Rear) Assy (3-1) #187 X 2 LC Flexible Retainer (3-2) Release LCD Flexible Board (3-3) Peel off LC Flexible Insulating Sheet (3-4) #2 / #10 X 1

Screw



Note1: ASSYLCDLCFP-1237


Note2: Refer to Assembly-2: Temporally secure FP-1237 FlexibleComplete Board when you assemble.

Note2: Assembly-2: Temporally secu re FP-1237 FlexibleComplete Board

Note3: Refer to Assembly- 3: Insulating Sheet A (SY) puttingposition when you assemble.

Note3: Assembl y-3: Insulating Sheet A (SY) putting posi-tion




Note6: Refer to Assembl y-5: LC Connect or Insulating Sheet,LC Flexible Insulating Sheet putting position when youassemble.

Note6: Assembl y-5: LC Connect or Insulati ng Sheet, LC

Flexible Insul ating Sheet putting po sition

#2#10

#196#201#187

Top ViewBottom ViewLCD Back

Note1: To remove Frame Assy, firstly remove LCD Flexible Boardand LC Flexible Insulating Sheet, then unfix FP-1237 FlexibleComplete Board.

#10:M1.7 X 4.0

(Silver)

2-599-475-31

4.0

1.7

#2: M1.7 X 4.0

(Black)

2-635-562-31

4.0

1.7

1.4

1.4

#187:M1.4 X 1.4

(Silver)

3-234-449-05

#196: M1.4 X 2.0

(Black)

4-178-124-01

2.0

1.4

#201: M1.4 X 2.0

(Silver)

4-178-124-21

2.0

1.4

57(Note3)

54

3-1

#187

#187

#2#10 (Note4)

#196#201(Note4)

51(Note6)

52

53(Note6)

53

3-4(Note5)

55

3-2

56

58

3 Main Frame Section(See Page 2-20)(Note1, 2)

Main Board Section

(See Page 2-16)

3-3

53(Note7)

SY-258


21/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-16


DISASSEMBLY

101 4-190-951-01 COVER, SIDE (210) (BLACK)

101 4-190-951-11 COVER, SIDE (210) (SILVER)

101 4-190-951-21 COVER, SIDE (210) (RED)

101 4-190-951-31 COVER, SIDE (210) (WHITE)

102 4-190-953-02 PLATE (L), BOTTOM GROUND (210)

103 4-190-955-01 PLATE (G), TOP GROUND (210)

104 4-190-954-01 PLATE (L), TOP GROUND (210)

105 4-190-957-01 LIGHT (MS), GUIDE (210)

106 4-186-573-01 INSULATING SHEET B (SY) (Note1)

107 A-1782-442-A SY-258 BOARD, COMPLETE (SERVICE)

108 4-191-035-01 SHEET (SY) (210), RADIATION (Note3)




#12 3-080-204-21 SCREW, TAPPING, P2

#192 4-188-736-01 SCREW (TP1.4), P2


4 #12 X 1

Note

2-2-3. MAIN BOARD SECTION

(NEX-3A/3D/3K)

5 #192 X 4

Screw

Note3: Refer to Assembly-18: Radiation Sheet (SY) (210) puttingposition (NEX-3A/3D/3K) when you assemble.

Note3: Assembly-18: Radiation S heet (SY) (210) puttingposition (NEX -3A/3D/3K )

Back View

#192

Note1: Refer to Assembly-10: Insulating Sheet B (SY) puttingposition when you assemble. Note1:

Assembly-10: Insulating Sheet B (SY) putting posi-tion

Note2: Refer to Assembly-11: Routing of Microphone Harnesswhen you assemble.

Note2: Assemb ly-11: Routi ng of Microphone Harnes s

#12Back View

#12:M1.7 X 5.0 (Tapping)

(Black)

3-080-204-21

1.7

5.0

#10:M1.7 X 4.0

(Silver)

2-599-475-31

4.0

1.7

#2: M1.7 X 4.0

(Black)

2-635-562-31

4.0

1.7

#192: M1.4 X 4.0 (Tapping)

(Black)

4-188-736-01

4.0

1.4



A

106(Note1)

108(Note3)

Solder

5 107

4 101

102

104

103

MIC902(Note2)

105

BT / RL Section(See Page 2-17)

#2#10(Note4)

#192

#192

#12

BB

BB

A

SY-25

8


22/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-17


DISASSEMBLY

151 X-2548-284-1 BASE ASSY, SHOE COVER (210B) (BLACK)

151 X-2548-285-1 BASE ASSY (210S), SHOE COVER (SILVER)

151 X-2548-286-1 BASE ASSY (210R), SHOE COVER (RED)

151 X-2548-287-1 BASE ASSY (210W), SHOE COVER (WHITE)

152 X-2548-283-1 FRAME ASSY, TOP (210)

153 4-186-543-01 PLATE, LOGO (BLACK)

153 4-186-543-11 PLATE, LOGO (SILVER)

153 4-186-543-21 PLATE, LOGO (RED) (RED)

153 4-186-543-31 PLATE, LOGO (S) (WHITE)

154 A-1782-349-A CABINET FRONT BLOCK ASSY (SERVICE) (BLACK)


154 A-1782-350-A CABINET FRONT BLOCK ASSY (SERVICE) (SILVER)


154 A-1782-351-A CABINET FRONT BLOCK ASSY (SERVICE) (RED)


154 A-1782-352-A CABINET FRONT BLOCK ASSY (SERVICE) (WHITE)


155 4-190-956-01 WINDOW (AF) (210)

156 X-2548-253-1 FRAME ASSY, BT (210)

157 A-1782-456-A RL BLOCK ASSY (SERVICE)

158 X-2548-279-1 CABINET (UPPER) ASSY (210B) (BLACK) (Note3)

158 X-2548-280-1 CABINET (UPPER) ASSY (210S) (SILVER) (Note3)

158 X-2548-281-1 CABINET (UPPER) ASSY (210R) (RED) (Note3)

158 X-2548-282-1 CABINET (UPPER) ASSY (210W) (WHITE) (Note3)

159 1-881-629-11 BT-063 FLEXIBLE BOARD

160 A-1773-791-A CN-439 BOARD, COMPLETE (Note5)

161 4-186-447-01 INSULATING SHEET (MS)

162 4-191-036-01 SHEET (CN) (210), RADIATION (Note4)

163 1-881-628-11 FP-1246 FLEXIBLE BOARD

164 4-186-569-01 INSULATING SHEET, LC FLEXIBLE (Note9)

165 4-190-950-01 SCREW, TRIPOD (210)

0BT900 1-756-813-11 LITHIUM RECHARGEABLE BATTERY (Note8)

0BT901 1-780-858-11 TERMINAL BOARD BATTERY




#12 3-080-204-21 SCREW, TAPPING, P2

#23 3-080-204-11 SCREW, TAPPING, P2

#71 3-208-537-01 0+Z M1.4X2 NEW TORASUTA

#192 4-188-736-01 SCREW (TP1.4), P2


6 #71 X 1

Note

2-2-4. BT / RL SECTION

(NEX-3A/3D/3K)

Screw

Note1: Refer to Assembly-17: Note on Alignment of the FlexibleBoard when assembling SY Holder Block Assy (NEX-3A/3D/3K) when you assemble.

Note1: Assembly-17: Note on Alignment of the Flex-ible Board when assembling SY Holder Block Assy (NEX-3A/3D/3K)

7 #12 X 2

8 #12 X 1 9 #12 X 3

Note2: Refer to Assembly-20: Routing of Microphone Harness(NEX-3A/3D/3K) when you assemble.

Note2: Assem bly-20: Routing of Micro phone Harness(NEX-3A/3D /3K)

Note3: Refer to Assembly-21: Assemble Cabinet (Upper) Assy(NEX-3A/3D/3K) when you assemble.

Note3: Assembly-21: Assemble Cabinet (Upper) Assy(NEX-3A/3D /3K)

Note4: Refer to Assembly-22: Radiation Sheet (CN) (210) puttingposition (NEX-3A/3D/3K) when you assemble. Note4: Assembly-22: Radiation Sheet (CN) (210) puttingposition (NE X-3A/3D/3K )

CautionDanger of explosion occurs if battery is incorrectly replaced. Replace onlywith the same or equivalent type.Dispose of used batteries accordingto the instructions.

Caution

#71

Back View

#12

Back View

Note5: Refer to Assembly-32: How to handle the Shutter FlexibleBoard (NEX-3A/3D/3K) when you assemble.

Note5: Assemb ly-32: How to handle the Shutter FlexibleBoard (NE X-3A/3D/3K )

#12

Back View

#12

Back View

#12:M1.7 X 5.0 (Tapping)(Black)3-080-204-21

1.7

5.0

#23:M1.7 X 4.0 (Tapping)(Black)3-080-204-11

4.0

1.7

#71:M1.4 X 2.0(Red)3-208-537-01

2.0

1.4

#10:M1.7 X 4.0(Silver)2-599-475-31

4.0

1.7

#192: M1.4 X 4.0 (Tapping)(Black)4-188-736-01

4.0

1.4

#2: M1.7 X 4.0(Black)2-635-562-31

4.0

1.7

Note:6Precautions for Replacement of Cabinet Front Block Assy (Service)As Cabinet Front Block Assy (Service) may be damaged by staticelectricity from its structure, handle it carefully like for the MOS IC.In addition, ensure that the receiver is not covered with dusts norexposed to strong light.

Note6:Assy

AssyMOS IC

Note7: Refer to PRECAUTION ON REPLACING THE CABINETFRONT on page 1-1 when replacing Cabinet Front Block

Assy (Service).

Note7: Assy1 - 1 PRECA UTION ON RE PLACIN G THE CAB INET FR ONT

Note8: Refer to Assembly-15: Lithium Rechargeable Battery puttingposition when you assemble.

Note8: Assembly-1 5: Lithium Rechargeable Batteryputting position

Note10:Refer to THE COMBINATION OF CABINETS COLORAND SCREW (NEX- 3A/3D/ 3K) on p age 2-12 about thecombination of cabinets color and screw.

Note10:2 - 12 THE COMB INAT ION OF CABI NETS COLOR AND S CREW(NEX-3A/3D /3K)

Imager Block Section(See Page 2-18)(including CP001 (CMOS imager) andIS-077 complete board)

154(Note6, 7)

: BT900 (LITHIUM RECHARGEABLE BATTERY)Board on the mount position.(See page Level3 6-34)

Solder

Solder

#23

#12

#12

#12

#71

6 160(Note5)

159

161

162

(Note4)

163

152

151

7 SY Holder Section(See Page 2-21)(Note1)

153

8 158(Note3)

157

9 156155

MIC901 (Note2)

BT901

BT900 (Note8)

CN-43

9

164

(Note9)

#2#10 (Note10)

#192

0 165

Note9: Refer to Assembly-35: Method of attachment of LC FlexibleInsulating Sheet (NEX-3A/3D/3K) when you assemble.

Note9: Assembly-3 5: Method of attachment of LC FlexibleInsulating Sheet (NE X-3A/3D/3K )

0 #2 / #10 X 1 #192 X 1

#2#10#192


23/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-18


2-2-5. IMAGER BLOCK SECTION

(NEX-3A/3D/3K)DISASSEMBLY

0201 A-1773-803-A MB CHARGE UNIT

0202 1-487-619-11 SHUTTER UNIT (H094)

203 Selection Parts IM WASHER (C), ADJUST (Note1, 2)

204 Selection Parts IM WASHER (B), ADJUST (Note1, 2)

205 Selection Parts IM WASHER (A), ADJUST (Note1, 2)

206 4-185-968-02 MB TAPE, MASK SHEET (Note3)

207 4-185-966-01 MB SHEET, MASK (Note3)

#148 3-057-082-21 SCREW (M1.7), NEW TRU-STAR, P2 (NEX-3A/3D/3K)

#191 4-188-735-01 SCREW (M1.7)

#197 4-185-990-01 MB SCREW, CHARGE UNIT FIXED

1. Remove to numerical order (qato qd) in the left figure.

Note

qa #191 X 3 qs #148 X 3

Screw

Note2: Refer to Assembly-23: IM Adjust Washer (A, B, C) puttingposition when you assemble.

Note2: Assembly-23: IM Adjust Washer (A, B, C ) puttingposition

Note3: Refer to Assembly-24: Method of attachment of MB MaskSheet when you assemble.

Note3: Assemb ly-24: Method of attachment of MB MaskShee t

#148

Back View

Note1: The type of these parts should be selected when performing

adjustments. Refer to "2-3. SELECTION PARTS" on page 2-23 .

Note1:

2 - 2 32-3. SE LECTION PARTS

#191

Back View

#148: M1.7 X 3.0

(Silver)

3-057-082-21

3.0

1.7

#191: M1.7 X 3.5 (Tapping)

(Black)

4-188-735-01

3.5

1.7

#197: M1.6 X 4.5 (Tapping)

(Silver)

4-185-990-01

4.5

1.6

206(Note3)

#197

202

qs 201#148

qaImager Unit Section(See Page 2-22) #191

203(Note1, 2)

204(Note1, 2)

205(Note1, 2)

207(Note3)

qd Cabinet Front Section(See Page 2-19)

Claw

Claw


24/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-19


251 4-185-964-03 MB N PLATE (A)

252 4-185-962-01 MB N PLATE (B)

253 4-185-963-01 MB N PLATE SP (Note1)

254 4-189-512-01 RING (210), ORNAMENTAL

255 4-186-534-01 BUTTON, L LOCK (BLACK)

255 4-186-534-21 BUTTON, L LOCK (RED)

255 4-186-534-31 BUTTON, L LOCK (WHITE)

255 4-186-534-41 BUTTON, L LOCK (SILVER)

256 X-2547-937-1 PIN ASSY, L LOCK

257 4-186-538-01 SPRING, LENS LOCK

258 4-189-412-01 GRIP (210) (BLACK) (Note5)

258 4-189-412-11 GRIP (210) (SILVER) (Note5)

258 4-189-412-21 GRIP (210) (RED) (Note5)

258 4-189-412-31 GRIP (210) (WHITE) (Note5)

259 4-189-413-01 SHEET (210), GRIP ADHESIVE

260 X-2548-232-1 CABINET (FRONT) ASSY (210B) (BLACK) (Note3)

260 X-2548-233-1 CABINET (FRONT) ASSY (210S) (SILVER) (Note3)

260 X-2548-234-1 CABINET (FRONT) ASSY (210R) (RED) (Note3)

260 X-2548-235-1 CABINET (FRONT) ASSY (210W) (WHITE) (Note3)

261 4-196-544-01 TAPE (AS (210))

262 4-189-417-01 BRACKET (L), STRAP (210)

263 4-193-982-01 WASHER, MF

264 A-1773-802-A MB CONTACT UNIT, N (Note2, 4)

#23 3-080-204-11 SCREW, TAPPING, P2

#148 3-057-082-21 SCREW (M1.7), NEW TRU-STAR, P2

#195 3-197-324-01 M1.7X2.5X3GF (D4X0.5)

#198 4-186-545-01 M1.7X4 SPIN

#199 4-195-871-01 SCREW, 0+Z M1.7

Note

2-2-6. CABINET FRONT SECTION

(NEX-3A/3D/3K)

ns: not supplied

Screw

Note1: Refer to Assembly- 27: Apply grease on MB N Plate SPwhen you assemble.

Note1: Assembly-2 7: Apply greas e on MB N Plate SP

Note2: Refer to Assembly-28: MB N Contact Unit holding positionwhen you assemble.

Note2: Assembly-2 8: MB N Contact Unit holding position

#23:M1.7 X 4.0 (Tapping)

(Black)

3-080-204-11

4.0

1.7

#148: M1.7 X 3.0

(Silver)3-057-082-21

3.0

1.7

2.5

1.7

#195: M1.7 X 2.5

(Silver)

3-197-324-01

4.0

1.7

#198: M1.7 X 4.0

(Silver)

4-186-545-01

3.0

1.7

#199: M1.7 X 3.0

(Black)

4-195-871-01

#23

257

256

255

254

253(Note1)

252

251

#195

#198

258(Note5)

259260(Note3)

#148

#148

264(Note2, 4)

263

#199

262

261

ns

ns

ns

Claw

Note3: Refer to PRECAUTION ON REPLACING THE CABINETFRONT on page 1-1 when replacing Cabinet (Front) Assy.

Note3: Assy 1 - 1 PRECAU TION ON REPLACING THE CABI NET FRONT

Note4: Refer to PRECAUTION ON REPLACING THE CABINETFRONT on page 1-1 when replacing MB N Contact Unit.

Note4: MB N 1 - 1 PRECAUTION ON REPLACING THE CABINET FRONT

Note5: 210 9BTAs sy210

Note5: To avoid damaging the claws, remove9BT Frame Assy (210)before removing Grip (210).


25/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-20


301 X-2548-251-1 FRAME ASSY (210)

302 4-186-555-01 LIGHT (LC), GUIDE,

0303 A-1779-038-A PANEL BLOCK ASSY (BLACK)

0303 A-1779-732-A PANEL BLOCK ASSY (SILVER)

0303 A-1779-733-A PANEL BLOCK ASSY (RED)

0303 A-1779-734-A PANEL BLOCK ASSY (WHITE)

304 4-190-763-01 BRACKET (G), STRAP (210)

305 4-186-571-01 SHEET, LC LIGHT INTERCEPTION

306 4-195-258-01 SHAFT, CUSHION (MF) (Note1)

#148 3-057-082-21 SCREW (M1.7), NEW TRU-STAR, P2

#192 4-188-736-01 SCREW (TP1.4), P2

#196 4-178-124-01 SPECIAL (M1.4 (D2.75)) (RED, BLACK) (Note2)

#201 4-178-124-21 SPECIAL (M1.4 (D2.75)) (SILVER, WHITE) (Note2)

Note

2-2-7. MAIN FRAME SECTION

(NEX-3A/3D/3K)

ns: not supplied

Screw

Note1: Refer to Assembly-8: Shaft Cushion (MF) putting positionwhen you assemble.

Note1: Assembly- 8: Shaft Cushion (MF) putting position



#148: M1.7 X 3.0

(Silver)3-057-082-21

3.0

1.7

#192: M1.4 X 4.0 (Tapping)

(Black)

4-188-736-01

4.0

1.4

#196: M1.4 X 2.0

(Black)

4-178-124-01

2.0

1.4

#201: M1.4 X 2.0

(Silver)

4-178-124-21

2.0

1.4

#196#201(Note2)

#148

304

302

305#192

ns

ns

301

306(Note1) 303


26/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-21


351 X-2548-275-1 HOLDER ASSY, SY (210B) (BLACK)

351 X-2548-276-1 HOLDER ASSY (210S), SY (SILVER)

351 X-2548-277-1 HOLDER ASSY (210R), SY (RED)

351 X-2548-278-1 HOLDER ASSY (210W), SY (WHITE)

352 X-2548-655-1 LID ASSY (210B) (SERVICE), BT (BLACK)

352 X-2548-656-1 LID ASSY (210S) (SERVICE), BT (SILVER)

352 X-2548-657-1 LID ASSY (210R) (SERVICE), BT (RED)

352 X-2548-658-1 LID ASSY (210W) (SERVICE), BT (WHITE)

353 X-2548-292-1 COVER ASSY, HDMI (210B) (BLACK)

353 X-2548-293-1 COVER ASSY (210S), HDMI (SILVER)

353 X-2548-294-1 COVER ASSY (210R), HDMI (RED)

353 X-2548-295-1 COVER ASSY (210W), HDMI (WHITE)

354 X-2548-288-1 COVER ASSY, USB (210B) (BLACK)

354 X-2548-289-1 COVER ASSY (210S), USB (SILVER)

354 X-2548-290-1 COVER ASSY (210R), USB (RED)

354 X-2548-291-1 COVER ASSY (210W), USB (WHITE)

355 4-190-890-01 CLAW, BT LOCK (210)

356 4-186-558-01 PLATE, SHOE COVER

357 4-190-893-01 SHAFT (210), BT LID

358 4-186-475-01 SPRING, BT LID OPEN (Note1)

359 4-190-961-01 LABEL (210), MS

360 4-209-617-01 HOLDER,SHEET(SY)

Note2-2-8. SY HOLDER SECTION

(NEX-3A/3D/3K)

ns: not suppliedNote1: Refer to Assembly-6: Method of attachment of BT Lid Assy

when you assemble.Note1: Assembly-6 : Method of attachment of BT Lid Assy

356

360

353

ns

359

357

351

358(Note1)

352

355

354


27/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-22


401 4-185-996-01 IM PLATE, IMAGER

402 A-1773-805-A IM PLATE UNIT, LOWPASS RETAINER

403 1-856-102-11 OPTICAL FILTER BLOCK (OFB-01-09) (Note1, 5)

404 4-193-875-01 CUTTER, IM FLARE (S)

405 4-185-993-01 IM SHEET, SPACER

406 4-194-127-01 IM TAPE, SPACER FIXED (S)

407 4-186-454-01 RADIATION SHEET (IS) (Note4)

408 4-189-415-01 HEAT SINK (210) (Note2)

409 1-880-963-11 IS-075 FLEXIBLE BOARD (Note3)



#191 4-188-735-01 SCREW (M1.7)

Note

2-2-9. IMAGER UNIT SECTION

(NEX-3A/3D/3K)

ns: not supplied

Screw

#27:M1.4 X 2.0(Black)

2-662-396-11

2.0

1.4

#191: M1.7 X 3.5 (Tapping)

(Black)

4-188-735-01

3.5

1.7

#27

#191

ns

401

402

405

406

410

407(Note4)

409(Note3)

#27408(Note2)

403(Note1, 5)

404

Note2: Refer to Assembly-29: Note when assembling Heat Sinkwhen you assemble.

Note2: Assembly-2 9: Note when ass embling Heat Sink

Note3: Refer to Assembly-30: Prior Insertion of IS-075 FlexibleBoard (NEX-3A/3D/3K) when you assemble.

Note3: Assem bly-30: Prior Insertio n of IS-075 Flex ibleBoard (NE X-3A/3D/3K )

Note4: Refer to Assembly-31: Radiation Sheet (IS) putting positionwhen you assemble.

Note4: Assembly-31: Radiatio n Sheet (IS) putting position

Note5: Refer to 3-2. CLEANING PROCEDURE OF OLPF on page3-5 for method of cleaning the OLPF.

Note5: OL PF3-5 3-2. CLEA NING PROCEDUREOF OLPF

Note1: Refer to the following statements when replacing the Opticalfilter block.

Method of Removal (1) Pour resolvent (alcohol or cleaning agent) between the

imager and the IM spacer sheet. Wait for that the adhesive power of the IM spacer fixed

tape weakens. (2) Remove the IM spacer sheet from the imager.

Pour resolvent (alcohol or cleaning agent)

between the imager and the IM s pacer sheet.

Method of Attachment (1) Attach the IM flare cutter and the Optical filter block by

aligning them with the outer shape of the IM spacer sheetevenly.

The two-layer side of the Optical filter block is on theimager side.

(2) Attach the IM spacer fixed tape by aligning it with theouter shape of the IM spacer sheet evenly.

The two-layerside is on theimager side.

Mount

Side

Imager

Side

Optical Filter Block




IM Flare Cutter

IM Spacer Sheet

IM Spacer

Fixed Tape

(3) Set the Optical filter block in its attachment jig(J-6082-737-A), with the attached IM spacer fixed tapefacing upward.

(4) Press the imager down into the jig as shown below toattach it to the Optical filter block.

J-6082-737-A

Imager

Peel off the released paper.

Note1:

(1) IM( ) IM (2) IM

IM()

(1) IMIM

2 (2) IMIM

2

IM

IM

IM

(3) IM (J-6082-737-A) (4)

J-6082-737-A


28/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L22-23E

Checking supplied accessories.

Note: This item is supplied with the unit as anaccessory, but is not prepared as a service part.

4-185-999-01 IM WASHER (C), ADJUST(t = 0.05)4-185-999-11 IM WASHER (C), ADJUST(t = 0.1)4-185-999-21 IM WASHER (C), ADJUST(t = 0.15)4-185-999-31 IM WASHER (C), ADJUST(t = 0.2)4-185-999-41 IM WASHER (C), ADJUST(t = 0.25)4-185-999-51 IM WASHER (C), ADJUST(t = 0.3)

4-185-999-61 IM WASHER (C), ADJUST(t = 0.35)4-185-999-71 IM WASHER (C), ADJUST(t = 0.4)4-185-999-81 IM WASHER (C), ADJUST(t = 0.45)4-185-999-91 IM WASHER (C), ADJUST(t = 0.495)

Part No. Description

4-185-998-01 IM WASHER (B), ADJUST(t = 0.05)4-185-998-11 IM WASHER (B), ADJUST(t = 0.1)4-185-998-21 IM WASHER (B), ADJUST(t = 0.15)4-185-998-31 IM WASHER (B), ADJUST(t = 0.2)4-185-998-41 IM WASHER (B), ADJUST(t = 0.25)4-185-998-51 IM WASHER (B), ADJUST(t = 0.3)4-185-998-61 IM WASHER (B), ADJUST(t = 0.35)4-185-998-71 IM WASHER (B), ADJUST(t = 0.4)4-185-998-81 IM WASHER (B), ADJUST(t = 0.45)4-185-998-91 IM WASHER (B), ADJUST(t = 0.495)

4-185-995-01 IM WASHER (A), ADJUST(t = 0.05)4-185-995-11 IM WASHER (A), ADJUST(t = 0.1)4-185-995-21 IM WASHER (A), ADJUST(t = 0.15)4-185-995-31 IM WASHER (A), ADJUST(t = 0.2)4-185-995-41 IM WASHER (A), ADJUST(t = 0.25)4-185-995-51 IM WASHER (A), ADJUST(t = 0.3)4-185-995-61 IM WASHER (A), ADJUST(t = 0.35)4-185-995-71 IM WASHER (A), ADJUST(t = 0.4)4-185-995-81 IM WASHER (A), ADJUST(t = 0.45)4-185-995-91 IM WASHER (A), ADJUST(t = 0.495)



2-3. SELECTION PARTS

Ref. No.203

Select the optimum thickness of washer.

Ref. No.204

Select the optimum thickness of washer.

Ref. No.205Select the optimum thickness of washer.

The CD-ROM supplied contains all of language version ofthe Handbook (PDF)for printing.

The printed matter is not supplied. If required,please order it with the part number below.

(Only for destination Japanese model)

Power cord (mains lead)

0 1-832-121-51 (CH) (NEX-5CK)

0 1-837-421-11 (UK, E (Saudi, Hong Kong))

0 1-837-422-11 (JE)

0 1-837-427-11 (AEP, E (EXCEPT Saudi, Hong Kong))0 1-837-428-11 (KR)

0 1-837-429-11 (AUS)

Rechargeable battery pack(NP-FW50)(Note)

USB cable1-829-868-31

Shoulder strap4-188-538-01

Body cap(Note)

Handbook (PDF)

CD-ROM- Application Software for camera- Handbook

NEX-3A/3D/3K4-191-926-01

NEX-5A/5D/5K/5CK4-191-823-01

Battery charger(BC-VW1)

0 1-487-907-11 (J)

0 1-487-907-21 (US, CND)

0 1-487-907-41 (EXCEPT US, CND, J)

Conversion (2P) Adaptor0 1-569-008-33

(E (Southeast Asia, Taiwan & Latin Area))

4-183-855-01 (JAPANESE)

* 4-183-855-11 (ENGLISH)

* 4-183-855-21 (FRENCH)

* 4-183-855-31 (ITALIAN)

* 4-183-855-41 (SPANISH)

* 4-183-855-51 (PORTUGUESE)

* 4-183-855-61 (GERMAN)

* 4-183-855-71 (DUTCH)

* 4-183-855-81 (TRADITIONAL CHINESE)

* 4-183-855-91 (SIMPLIFIED CHINESE)

* 4-189-192-11 (RUSSIAN)

* 4-189-192-21 (ARABIC)

Conversion (2P) Adaptor0 1-569-007-12 (JE)

FlashA-1774-691-A

Flash case

4-186-787-01

* 4-189-192-31 (PERSIAN)

* 4-189-192-41 (KOREAN)

* 4-189-192-51 (POLISH)

* 4-189-192-61 (CZECH)

* 4-189-192-71 (HUNGARIAN)

* 4-189-192-81 (SLOVAK)

* 4-189-192-91 (SWEDISH)

* 4-189-193-11 (FINNISH)

* 4-189-193-21 (NORWEGIAN)

* 4-189-193-31 (DANISH)

* 4-189-193-41 (THAI)

* 4-189-193-51 (UKRAINIAN)

Instruction Manual(Only for destination Japanese model)

4-183-856-01 (JAPANESE)4-183-856-11 (ENGLISH)

* 4-183-856-22 (FRENCH, ITALIAN)

* 4-183-856-31 (SPANISH, PORTUGUESE)

* 4-183-856-42 (GERMAN, DUTCH)

* 4-183-856-51 (TRADITIONAL CHINESE,SIMPLIFIED CHINESE) (E)

* 4-183-856-61 (RUSSIAN)

* 4-183-856-71 (ARABIC, PERSIAN)4-183-856-81 (KOREAN)4-183-856-91 (SIMPLIFIED CHINESE)

(CH) (NEX-5CK)

* 4-183-857-11 (POLISH)


29/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L23-1

3. ASSEMBLY

Frame Assy

Before assembling Frame Assy, temporally secureFP-1237 Flexible Complete Board.

FP-1237 Flexible Complete Board

Edge of

Frame Assy

Assembly-2: Temporally secure


Assembly-3: Insulating Sheet A (SY) putting position

Insulating Sheet A (SY)

Align with the upperedge of the connector.

Align with the right edgeof the connector.

Align with thelower edgeof the ground.

Assembly-4: LC Flexible Insulating Sheet

putting position

Ground

FP-1237 Complete BoardLC Flexible Insulating Sheet

Assembly-5: LC Connector Insulating Sheet,

LC Flexible Insulating Sheet

putting position

LC Connector Insulating Sheet


Without running on the edge.

LC Cabinet (Rear) Assy

BT Lid Assy

Assembly-6: Method of attachment of BT Lid Assy

BT Lid Shaft

Cabinet (Rear) Assy

BT Lid OpenSpring

B

A

AB

Tighten the four screws in sequence of 1 to 4 as shown below.

Cabinet (Rear) Assy

Cabinet (Front) Assy

Assembly-7: Screw tightening sequence when

assembling the exterior parts

(NEX-3A/3D/3K)

Tighten the two screws in sequence of 1 to 2 as shown below.

Grip (210)

1

2

Tighten the five screws in sequence of 1 to 5 as shown below.

Front Cabinet Assy

Rear Cabinet Assy

12

3 4

5

Side Cover (210)

1

23

4

Assembly-8: Shaft Cushion (MF) putting position

Frame Assy

Without runningon the mold part.

Shaft Cushion (MF)

Assembly-1: Method of attachment of

Cabinet (Rear) Assy

Open the LCD as shown below.

Fit the Cabinet (Rear) Assy along the angle of LCD.

Incline Cabinet (Rear) Assy while turning it counterclockwise,then fit it in LCD.


30/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L23-2


Without running on theblack printing area onFP-1237 Flexible CompleteBoard

Without running off theedge of FP-1237 FlexibleComplete Board


Assembly-9: LC Flexible Insulating Sheet

putting position

Insulating Sheet B (SY)

SY-258 Complete Board Without running on the chip.

Assembly-10: Insulating Sheet B (SY) putting po sition

Assembly-11:Routing of Microphone Harness

Insert the surplus partinto the Front Cabinet.

Pass the harnesses through thecorner of SY-258 Complete Board.

SY-258 Complete Board

MicrophoneHarness

CN-439Complete Board

BT Frame Assy

Insert Gasket (MS) between BT Frame Assy andCN-439 Complete Board without evagination.

Assembly-12: Inserting Gasket (MS)

(NEX-5A/5D/5K/5CK)

Gasket (MS)

BT Holder Block Assy

Shutter Unit

Assembly-13:Assemble BT Holder Block Assy

(NEX-5A/5D/5K/5CK)

Shutter Flexible Board


(NEX-5A/5D/5K/5CK)

SP Holder Route the part shown withbroken line inside SP Holder.

RL Block AssyMicrophone Harness

NEX-5A/5D/5K/5CK

Assembly-15:Lithium Rechargeable Battery

putting position

NEX-3A/3D/3K

Printing shows position ofLithium Rechargeable Battery

Printing shows positionof Lithium RechargeableBattery

Soldering

Soldering

RL-103 Complete BoardLithium Rechargeable Battery

Lithium Rechargeable Battery RL-101 Complete Broad

Note: Make sure that the PW Knob isturned to OFF position whenassembling RL Block Assy.

RL Block Assy

PW Knob

Assembly-16:Note when assembling

RL Block Assy

(NEX-5A/5D/5K/5CK)

Assembly-17:Note on Alignment of the Flexible Board

when assembling SY Holder Block Assy

(NEX-3A/3D/3K)

SY HolderBlock Assy

Outside SY HolderBlock Assy

Under SY HolderBlock Assy

Above SY HolderBlock Assy

Between Shutter Unitand SY Holder Block AssyUnder SY Holder

Block Assy

Radiation Sheet (SY) (210)


Attach Radiation Sheet (SY) (210) on SY-258 CompleteBoard without running off more than two corners of the IC.

Assembly-18:Radiation Sheet (SY) (210)

putting position

(NEX-3A/3D/3K)

Jack Cover BaseUnder Jack Cover Base

Above Jack Cover Base

Assembly-19:Note on Alignment of the Flexible Board

when assemblingJack Cover Base

(NEX-5A/5D/5K/5CK)


31/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L23-3


(NEX-3A/3D/3K)

Microphone

Cabinet (Upper) Assy

Insert the surplus part intothe hole as shown here.

Route the harnesses under thetwo ribs of Cabinet (Upper) Assy.

Cabinet (Upper) Assy

RL Block Assy

Note: Make sure that the PW Knobis turned to OFF positionwhen assembling Cabinet(Upper) Assy to RL Block

Assy.

PW Knob

Assembly-21:Assemble Cabinet (Upper) Assy

(NEX-3A/3D/3K)

Assembly-22:Radiation Sheet (CN) (210)

putting position

(NEX-3A/3D/3K)

CN-439 Complete Board

FP-1246Flexible Board

Radiation Sheet(CN) (210)

Within 1.0mm

Without running on thereinforcement board

Within 1.0mm

Cabinet (Front)

IMAdjust Washer B IMAdjust Washer A

IMAdjust Washer C

Assembly-23: IM Adjust Washer (A, B, C)

putting position

Assembly-25:BT Slider Sheet (front) putting position

(NEX-5A/5D/5K/5CK)

BT Slider Sheet (front)

Rib edge (horizontal):

0.5mm

Rib edge (vertical):0.5mm

Lib edge (vertical):0.5mm

MB N Plate SP

Assembly-27:Apply grease on MB N Plate SP

G G-85(J-6082-626-A)

BT Slider Sheet(horizontal)

Cabinet (Front)

Assembly-26:BT Slider Sheet (horizontal)

putting position

(NEX-5A/5D/5K/5CK)

From edge(vertical):1.0mm

From edge(horizontal):

1.0mm

J-6082-735-A

MB Mask Sheet

Note:There should not be any misalignment when attachingMB Mask Sheet.

MB MaskSheet Tape

Cabinet (Front)

Assembly-24:Method of attachment of MB Mask Sheet


32/33

NEX-3A/3D/3K/5A/5D/5K/5CK_L23-4

Hold here

Assembly-28:MB N Contact Unit holding position

MB N Contact Unit

Insert IS-075 Flexible Board into the connector onIM Imager Unit 14M, then lock the connector.

Assemble Heat Sink and IM Imager Unit 14M.

Note: IS-075 Flexible Board can not be inserted afterassembling Heat Sink.

Heat Sink

IM Imager Unit 14M

IS-075 Flexible Board

Assembly-30:PriorInsertion of IS-075 Flexible Board

(NEX-3A/3D/3K)

Radiation Sheet (IS)

Heat Sink

Without running off theedge of the hole.

Without running on theedge of Heat Sink.

Assembly-31:RadiationSheet (IS) putting position


CN-439 Complete BoardPut the surplus part of theshutter flexible board underSY-258 Complete Board.

Assembly-32:How to handle the Shutter Flexible Board

(NEX-3A/3D/3K)

Assembly-29:Note when assembling Heat Sink

Align with the positioning hole.

Heat Sink

CN-439Complete Board

LC ConnectorInsulating Sheet

BT Frame Assy

Within 0.5mm

Within 0.5mm

Assembly-33:LC ConnectorInsulating Sheet

putting position

Assembly-34:Tape AS (210) putting position

(NEX-5A/5D/5K/5CK)

Tape AS (210)

Without protrudingfrom the rib top surface.

Without running offthe mask sheet.

Without running on this boss.

Assembly-35:Method of attachment of LC Flexible

Insulating Sheet

(NEX-3A/3D/3K)

Bend the LC Flexible Insulating Sheet alongthe curve of BT-063 Flexible Board.

LC FlexibleInsulating Sheet

1.0mm


33/33

3-2. CLEANING PROCEDURE OF OLPF

If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.Note:Protection sheet is for preventing the scratch of a surface on the Jig (Tip). The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

If you cannot remove dirt with remedy above, cleaning by the following jig are used.Soak a small amount of EE3310 (Liqui d cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

1. Put the two cleaning cloths on a tray like below. 1Souse the one cleaning cloth in ethyl alcohl. 2Put the other cleaning cloth on a tray as it is dry.2. Dab the tip of CCD cleaning jig at the cleaning cloth of15 or 6 times. *Do not slide the tip from right to left or up and down while dabbing.3. Dab the tip of CCD cleaning jig at the cleaning cloth of25 or 6 times.

*

Do not slide from right to left or up and down while dabbing.4. Wait until the tip will be dried completely.

1. Clean up the tip of CCD cleaning jig.2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight. *Do not slide from right to left or up and down while dabbing.3. Repeat 3 several times to clean up.4. According to service manual, check if there is dirt on the CCD.

CCD Cleaning Jig (New)

(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

1 Souse the cleaningcloth in ethyl alcohol.

2 The dry cleaning cloth.

OLPF

Cleaning Jig(J-6082-635-A)

Cleaning Cloth(J-6082-636-A)

Cut

EE3310

sony nex 5 service manual level 1

Documents

interchangeable lens

sony nex

interchangeable lense

interchangeable lens

service manual level

following service manual

oss service manual

dolby digital