FESTIVE SEASON PLANNINGSBS-REF

SUPPORT FUNCTION

1-1. SBS installation will be done same time by product specialist.

1-2. Loading & Unloading will be taken care for safe handling of product.

1-3. Demo will be covered by product specialist after the complete installation.

Festive Season Planning for SBS REF

Festive Season Planning for SBS REF

SBS REF INSTALLATION PROCESS

PREPARATION BEFORE INSTALLATION

Festive Season Planning for SBS REF

1. Entrance Check

1-1. Check if the ref goes through the entrance.

MIN(800㎜)

A

B

C

D

E

FMODEL DIMENSIONS

(A-B-C-D-E-F)

REF VPP60ZPS-FSC 651*65*25*655*942*1808

REF VPL60ZPS-FSC 600*57*5*675*908*1760

REF VPS65ZLM-FSC 600*57*5*675*908*1760

Fridges with more than 750mm of “D” are not able to go into the elevator. So, disassemble the doors or use a ladder car.

HOW TO DELIVER & UNPACK THE PRODUCT

Festive Season Planning for SBS REF

1. Loading/Unloading of Ref.

Loading

Unloading

Transporting

1-1. Loading

When loading products, make sure to use fork lifts and work by 2 personnel as a team. 1-2. Transporting

To prevent products from moving freely, fix the products with rubber bands.

1-3. Unloading

When unloading products, also make sure to use fork lifts and work by 2 personnel as a team.

Make sure that products shall not be bumped on the corners and fallen down.

Festive Season Planning for SBS REF

Space Procurement

CoverDisassembly

2-1. Space Procurement

Secure enough space to remove the packaging box.

2-2. Removing packing box

Be careful not to scratch the product with EPS or Angle and make sure to check the outer appearance after removing all packaging materials.

2-3. Disassembling Front Cover

Open the F/R-Doors, remove screw caps (3ea) and remove the Front Cover screws (3ea) by turning them counter-clockwise.

For the dispenser model, remove the water pipe clamping clip.

Detach the front cover first before moving the ref after removal of the packaging box.

PackageRemoval

HOW TO DELIVER & UNPACK THE PRODUCT

PRECAUTION BEFORE INSTALLATION

1. Delivery

1-1. Upon loading/unloading the ref, make sure that 4 personnel work as a team.1-2. Upon delivery, make sure to use protection materials preventing any damage.1-3. Move the ref carefully after getting rid of the packaging box.

2. Installation

2-1. Check if the floor is leveled. If the floor is not leveled, it causes vibration and noise, and when opening/closing the doors, the refrigerator could be tipped over resulting in personal injuries. 2-2. For dispenser models, select a place easy to access the water supply with little humidity.

2-3. Install the set maintaining adequate distances from the surrounding. If there is not enough space around the set, power consumption will be increased due to weak cooling power caused by insufficient ventilation.

2-4. Keep it away from places with direct sun light, much heat or too low temp. A place with a surrounding temp ranging from 5℃ to 43℃ is recommended. A place with too high/low temps causes problem and affects cooling power.

Festive Season Planning for SBS REF

PRECAUTION BEFORE INSTALLATION

3. Function Check

3-1. Carry out a water leakage test after completing the water supply connection. 1) Let more than 1.2L water flow by pressing the Water Lever. 2) Let water pass by pressing the Ice Maker Test button for 3 times repeatedly. 3) Check for any water leakage in the order of Water Connector/ Water Tube Valve/ Inlet & Outlet of Water Valve and Coupler at the lower part of the door.

3-2. Check if the ref is leveled and there are no level differences between the doors. 1) Check if the ref is rocking and the adjusting legs are completely set on the floor.

2) Check if there are level differences of doors and if any, adjust it with the adjusting bolt.

3-3. Check if the room lamps work normally.

Festive Season Planning for SBS REF

THANKS