taktlnow product data sheet doc. sp38-1 rev. 2004 - facade

TAKTLNOW® Product Data SheetDoc. SP38-1 Rev. 2004

1 of 6230 Braddock Avenue, Turtle Creek, PA 15145 | TAKTL-LLC.COM | 412.486.1600 | [email protected]

TAKTLNOW® Architectural Ultra High Performance Concrete (A|UHPC®) offers first-quality production overruns of our standard product at a lower cost and in smaller, more manageable quantities. TAKTL is over four times as strong as traditional concrete, will not degrade from salt and freeze–thaw conditions, and provides designers with an extremely broad color and surface texture design palette.

Tested and Approved for Extreme Conditions (Test reports available upon request)High impact/abuse resistance (ASTM C1629) Excellent freeze-thaw performance (ASTM 1185-08)

Non-Combustible (NFPA 285) Approved for installation in Seismic Zones (CA, HI)

Design + Installation Features Performance AdvantagesIntegral pigment (through-color) Does not rust, rot, corrode, or attract termites, mold or fungus

Low installation costs (wider anchor spacing) Stronger than wood, terracotta, fiber cement, and thin profile stone

Wide range of colors and unique textures Does not require edge sealers

Compatible with stone, concrete, wood and metal stud walls Impermeable and Chloride-Resistant

Can be installed on basic hat channels and wood furring Resistant to surface scaling over time

Easily field cut and drilled to exact measurements Minimal long-term maintenance



Material/Panel CharacteristicsMaterial Density 137lbs/ft3

Coefficient of Thermal Expansion 6.41 E-06 in/in/°F

Compressive Strength 12,000 psi – 18,000 psi (95Mpa – 120Mpa)

Flexural Strength (Panel) 3,916 psi – 4,786 psi (27Mpa – 33Mpa)

Visible Fastener Load Values* 16GA/50ksi Steel & 2.2mm Aluminum 738 lbf Shear | 1,620 lbf Tension

Standard Base Panel Thickness** 5/8 in (16mm) (11/2 in/38mm Max.)

Panel Weight 5/8" (16mm) Thickness min. 7.2 lb/f2 (33.7kg/m2) – 7.8 lb/f2 (38.08kg/m2)

*Recommended minimum design values **Consult a TAKTLNOW Specialist for panel thickness of selected product

NOTE: Refer to TAKTL Product Literature test reports available upon request

Code Compliance & Reference StandardsIntertek/ICC-ESR (AC10) Quality Management System certification & auditing

IBC & IRC 2012 & 2015 Building Code Compliant

ICC-ESR (AC90) Evaluation Service Report (ESR)

ASTM C1186 Type A (exceeding Grade IV in strength and durability)

ASTM E136 Non-combustibile

ASTM E84 Class A finish

NFPA 285 Wall Assembly Fire Test

ASTM 1629 Impact Test

What is UHPC? Ultra High Performance Concrete (UHPC) is a classification of concrete that is orders of magnitude stronger than wood, terracotta, GFRC, and fiber cement. UHPC derives its high performance from a carefully calibrated ratio of engineered ingredients and a mixing sequence that packs molecules closely together to create very tight bonds. The high packing density yields excellent flexural and compressive strength while minimizing the capillary pores that cause freeze-thaw or chloride degradation in other cement-based products.

Description The TAKTL A|UHPC® panels are Ultra High Performance Concrete panels manufactured from Portland cement, micro aggregates, and additives, with alkali-resistant glass fibers and two layers of alkali-resistant glass fiber reinforcement mesh. TAKTL panels are designed to comply with a range of facade assemblies for all building construction types (Type I through V). TAKTL panels are also suitable for interior application as part of a Class A interior wall.

Application The TAKTLNOW A|UHPC Panel System is used as an exterior and interior wall cladding in the following applications: • ALL types of construction under the 2012 & 2015 IBC and IRC• Renovations and re-cladding over existing substrate• Interior cladding, partitions, and feature wall finishes

Features + Advantages• Compatible with all wall assemblies/substrates• Highest strength-to-weight ratio in its class • Impermeable; chloride resistant • Excellent freeze-thaw resistance and strength retention• Non-combustible, Class A smoke and flame spread• Impact resistance > highest rating under ASTM 1629• Delivered precut and easy to field cut and drill as needed

Quantities TAKTLNOW is pre-packaged and sold by the crate, with minimum quantities starting at 220 ft2, making it perfect for a wide variety of indoor, outdoor, and transitional applications that are below our standard minimum for made-to-order product. Current inventory is available on our website and upon request. Availability changes frequently, depending upon current production, check back often. Click for Inventory

Price TAKTLNOW is priced at $8.95 per square foot (including crating), representing a savings of over 55%.

Samples + Orders To place an order, request samples, or learn more about the installation methods, please contact a TAKTLNOW Support Specialist: (412) 486-1600, or [email protected].

Panel Type and Dimensions

TypeNominal Actual

Thickness**Length Width Length Width

A 60" 6" 59.5" 5.5"

1/2", 5/8", 3/4", or 1"

B 72" 6" 71.5" 5.5"

C 60" 12" 59.5" 11.5"

D 60" 24" 59.5" 23.5"

E 72" 24" 71.5" 23.5"

**Consult a TAKTLNOW Specialist for panel thickness of selected product

Price GuideProduct Minimum Quantity Price

TAKTLNOW Panel 220 Ft2 7.95/ft2

Visible Fasteners (Color-matched) 1 Box (250 Fasteners) 0.75/Fastener

https://www.taktl-llc.com/taktlnow/



Standard Textures

Arbos I Arbos IIRioShadowsCrinkleRough 2Rough 1Smooth Reeds

White 87 Platinum 75 Titanium 63 Grey 52 Graphite 40 Bone 78 Sand 72 Dune 60 Terracotta 52

Colors

White Platinum Titanium Grey Graphite Bone Dune Flax Terracotta

Note: Color and texture representations not shown in the images above are available upon request.

KORSA Finishes The KORSA collection from TAKTL utilizes innovative manufacturing methods to combine the time-tested performance of A|UHPC concrete facade elements with the depth and richness of exposed decorative aggregates.

Examples of KORSA finishes

KORSA™ Decorative Aggregates

Mediablast Surfaces of raised and flat textures are mediablasted to resemble sand-like finishes, resulting in a subtly lighter and visually varied effect.

Cast finish

Mediablast

Mediablast finish

Textures, Colors, and Finishes



Wood/Metal Brick CMU Block Concrete

Attachment Install TAKTLNOW panels with fasteners* over basic hat channel, wood furring, z-girt, or other preexisting attachment assembly systems. Panel and subframe fasteners must be made of high-corrosion resistant Type 304 stainless steel. *Color matched fasteners available from TAKTL

Panel Spacing TAKTL recommends a ½” reveal between panels and anchor spacing of 24" to 36", depending on application.Visible Fastener Fasten TAKTLNOW panels directly to the supporting framing with self-drilling Type 304 austenitic stainless-steel fasteners with powder-coated, color-matched heads. (Figure 1.1)Wall Types Install TAKTLNOW panels using hat channels compatible with wood frame, brick, CMU block, concrete wall or 16-18 gauge metal subframe. (Figure 1.2)

Refer to a registered engineer for panel support system design and analysis, including connection to the substrate/backup wall and load capacity information.

Figure 1.1 Fastener Detail or Color-matched Fastener

Figure 1.2 Wall Types (Section details can be found on pages 7 and 8

Field ProcessingDrilling + Cutting TAKTLNOW panel requires wet cutting and drilling to reduce heat build up, to sustain blade and drill bit life, and to produce clean cuts and holes.

Project engineer or installation contractor determines anchor quantity and spacing per local codes, standards, and environmental conditions.

Field Guidelines + Recommendations• Check for anchor hole locations prior to start cuts• Pilot holes recommended for all drilling larger than ¼"• Penetrations 2"– 3" from edge of panel (for penetrations <2"Ø)• Provide 6”– 36" clearance between penetrations (off-center)

Reference TAKTL Field Guide for detailed instructions on processing, handling, PPE, care, and maintenance. Available on our website. Figure 1.3 Open Square Figure 1.4 Open Quirk Miter

Figure 1.3 Open Square Corner Condition ExampleAll TAKTLNOW panels are square cut.

Figure 1.4 Open Quirk Miter Corner Condition ExampleQuirk Miter may be achieved through field processing, but is not a standard option provided by TAKTL.

Corner Conditions

Recommended Cutting Tools

Saw DeWalt DWC860 4-3/8" Wet Dry Masonry Saw

Alpha 5" Wet Stone Cutter/Saw AWS-125

Makita 4101RH 5" Cutter

MK-1590 Wet Cutting Rail Saw (for longer cuts and higher volume)

Blade Continuous Rim Diamond Saw Blade

Recommended Drilling Tools

Drill Non-Hammer Drills (wet recommended)

Drill Bit (Small) Bosch GT3000 Glass & Tile Set (1/8"– 3/4")

Steelex D3731 Glass Cutting Drill Bits (1/8"– 3/4")

Drill Bit (Large) Hitachi 728792C Carbide Grit for Hole Saw (2 1/2")

Greenlee 725-4-1/8 Carbide-Grit Hole Saw (4 1/8")

Recommended Tools

Installation



Select Application Examples

Exterior Cladding | 1 Color, 3 Textures, 1 Finish Exterior Cladding | 1 Color, 2 Textures, 2 Finishes

Exterior Cladding | 1 Color, 2 Textures, 1 Finish

Interior Ceiling Cladding | 2 Colors, 2 Textures, 2 FinishesInterior/Exterior | 2 Colors, 3 Textures, 1 Finish

Exterior Cladding | 1 Color, 1 Texture, 2 Finishes



Environmental, Health + Safety• Most UHPC is formulated with quartz sand and contains

more than 40% crystalline silica, a known carcinogen. TAKTL has been specifically formulated without using quartz sand and has extremely low crystalline silica content of only .03 – 0.633%.

• Health Product Declaration (HPD) and Safety Data Sheet (SDS) available upon request.

• TAKTL A|UHPC is manufactured with 90% raw materials sourced within 500 miles of the factory.

• For further information about potential LEED credit contri-bution, consult TAKTL Technical Support.

• Refer user to Safety Data Sheets and Installation Guide before working with TAKTL products.

Contact TAKTLNOW Support Specialist (412) 486-1600 | [email protected] 230 Braddock Avenue, Pittsburgh, PA 15145

Related LiteratureTAKTL Technical Summary Field GuideCertified Test Results Product Data SheetICC ESR-3899 Texture Data Sheet

Exterior Cladding | 1 Color, 2 Textures, 1 FinishExterior Cladding | 1 Color, 1 Texture, 1 Finish

Exterior Cladding | 3 Colors, 2 Textures, 2 Finishes Exterior Cladding | 1 Color, 2 Textures, 2 Finishes

https://www.taktl-llc.com/wp-content/uploads/2019/04/SP18-1-TAKTL-Technical-Summary.pdf

https://www.taktl-llc.com/wp-content/uploads/2019/04/P10-1-Field-Guide-Interactive.pdf

https://www.taktl-llc.com/wp-content/uploads/2019/06/T2-1-TAKTL-Certified-Test-Results-US.pdf

https://www.taktl-llc.com/wp-content/uploads/2019/11/SP20-1-TAKTL-Product-Data-Sheet.pdf

https://www.taktl-llc.com/wp-content/uploads/2020/03/SP-2-1-TAKTL-Texture-Datasheets.pdf


230 Braddock Avenue, Turtle Creek, PA 15145 | TAKTL-LLC.COM | 412.486.1600 | [email protected]

TAKTLNOW Installation Detail | 5/8" TAKTL Panels + Metal Hat Channel

6” STUD WALL

SHEATHING W/AVB / WRB

16GA, 5” HAT CHANNELPAINTED BLACK

16GA, 2” HAT CHANNELPAINTED BLACK

1 3/

4” M

in.

1 3/

4” M

in.

1/2”5”

6 13

/16”

5/8” TAKTL

3/4” (SELF TAPPING/PRE-DRILLED)

Note: SELF DRILLINGBI-METAL SCREW REQUIRESCAVITY OF 1” (1/4” SHIM)

This detail drawing represents an example of cladding assembly for reference only.

Addendum I


230 Braddock Avenue, Turtle Creek, PA 15145 | TAKTL-LLC.COM | 412.486.1600 | [email protected]

TAKTLNOW Installation Detail | 5/8" TAKTL Panels + Wood Furring Installation

This detail drawing represents an example of cladding assembly for reference only.

6” STUD WALL (16” O.C.)

1”X 6” MIN. TREATED WOODPAINTED BLACK

1”X 3” MIN. TREATED WOODPAINTED BLACK

TORX SCREW (1 1/2” MAX.)

2”W X 8”H X 1/4” MIN.SHIM/SPACER FOR DRAINAGE

1/2”5”

1 3/

4” M

in.

1 3/

4” M

in.

OPTIONHIGH. PERM. BLACK MEMBRANE@ FACE OF FURRING & STANDARD TYVEK SHEATHING

5/8” TAKTL

SHEATHING W/AVB / WRB

1” Min.

Addendum II

taktlnow product data sheet doc. sp38-1 rev. 2004 - facade

Documents