tariff concessions chapter 2073-7301-7310.29 · standards a106/a106m - 08, grade b (astm a106/a106m...
TRANSCRIPT
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7302.10 RAILS, flat bottom, less than 20 kg/m
Op. 21.02.1984 Dec. 21.02.1984 - TC 8341714
7302.10 RAILS, crane, railway type, weight EXCEEDING 70 kg/m
Op. 14.06.1988 Dec. 18.08.1988 - TC 8805556
7302.10.00 RAIL, CONSTRUCTION, conforming to European Standard EN 14811,
being ANY of the following:
(a) 73C1;
(b) 75C1;
(c) 76C1;
(d) 105C1;
(e) 310C1
Op. 20.11.2015 Dec. 11.02.2016 - TC 1542183
7302.10.00 RAIL, GROOVED, conforming to European Standard EN 14811, being
ANY of the following:
(a) RI53-10;
(b) RI55NK;
(c) 51R1;
(d) 53R1;
(e) 54G2;
(f) 55G1;
(g) 55G2;
(h) 57R1;
(i) 59R1;
(j) 59R2;
(k) Ri60NL;
(l) 60R1;
(m) 60R2;
(n) 60R3;
(o) 62R1;
(p) 62R2;
(q) 63R1;
(r) 67R1
Op. 27.10.2015 Dec. 18.01.2016 - TC 1540089
7302.10.00 RAIL, grooved, being ANY of the following:
(a) Ri57A;
(b) 57A
(c) Ri60R1;
(d) Ri60;
(e) Ri60-10;
(f) 60Ri1;
(g) 60R1
Op. 09.07.2010 Dec. 29.09.2010 - TC 1031338
7302.10.00 RAIL TRACK, comprising NOT less than 0.84% carbon
Op. 10.08.2005 Dec. 28.10.2005 - TC 0510522
7302.10.00 RAIL, having ALL of the following:
(a) elevated guardrail configuration;
(b) overall height 93 mm;
(c) rail head height 38 mm;
(d) neck height 40 mm;
(e) base (foot) height 15 mm;
(f) rail head width 80 mm;
(g) base (foot) width 40 mm
Op. 22.06.1998 Dec. 28.08.1998 - TC 9805404
7302.30.00 RAIL, ASYMMETRICAL POINTS, having ALL of the following:
(a) tongue rail configuration;
(b) base width 140 mm;
(c) overall height 134 mm;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(d) rail head width 74.5 mm;
(e) rail head height 53 mm;
(f) neck height 47.3 mm
Op. 09.04.1998 Dec. 10.06.2010 - TC 1025922
7302.90.00 CLIPS, CRANE RAIL
Op. 05.06.2008 Dec. 22.08.2008 - TC 0811455
7303.00.00 PIPES, cast iron, complying with European Standard EN877:1999
(EN877:1999) having EITHER of the following:
(a) internal coating of epoxy resin, outer coating of
acrylic primer;
(b) internal coating of epoxy, outer coating of zinc and
acrylic primer
Op. 14.09.2006 Dec. 08.12.2006 - TC 0617186
7304.11.00 LINE PIPE, seamless, stainless steel
Op. 04.04.2007 Dec. 22.06.2007 - TC 0704964
7304.19.00 LINE PIPE, seamless, circular cross section, complying with
American Petroleum Institute Standard Specification 5L (API 5L),
having EITHER of the following:
(a) diameter less than 33.7 mm;
(b) diameter exceeding 168.3 mm
Op. 20.07.2012 Dec. 12.11.2012 - TC 1224023
7304.19.00 LINE PIPE, carbon steel, conforming to American Society of
Testing and Materials ASTM A106 Grade B, being ANY of the
following, as listed in THE TABLE:
THE TABLE
TYPE OD WT
(a) 200NB Schedule 160 219.10 mm 23.01 mm;
(b) 250NB Schedule 80 273.10 mm 15.09 mm;
(c) 200NB Schedule 40 219.10 mm 8.18 mm;
(d) 80NB Schedule 80 88.90 mm 7.62 mm;
(e) 20NB Schedule 160 26.7 mm 5.56 mm
For the purposes of this order, all measurements have a tolerance
of + OR - 5%
Op. 05.01.2011 Dec. 04.04.2011 - TC 1100573
7304.19.00 LINE PIPE, seamless, circular cross section, having EITHER of
the following:
(a) outside diameter (OD) NOT greater than 168.3 mm;
(b) wall thickness (WT) NOT less than 16 mm,
and complying with EITHER of the following:
(a) American Society of Testing and Materials
Standards A106/A106M - 08, grade B (ASTM A106/A106M - 08,
grade B);
(b) American Petroleum Institute Standard API
specification 5L, grade X42 (API specification 5L,
grade X42)
Op. 13.08.2010 Dec. 08.11.2010 - TC 1037312
7304.19.00 LINE PIPE, seamless, to Specification ASTM A333 Grade 6,
having EITHER of the following:
(a) OD exceeding 209.0 mm;
(b) a WT of 12.5 mm or greater
Op. 01.01.2007 Dec. 08.11.2006 - TC 0614208
7304.19.00 TUBES OR HOLLOW BARS (NOT BEING HONED TUBES), in straight lengths,
ends plain, bevelled or threaded in accordance with ANY of the
following tube, hollow bar or pipe material Specification options:
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
but without further rework, having a length NOT less than four
times the OD, as listed in THE TABLE:
THE TABLE
Outside Dia Wall Thickness
(a) NOT exceeding 219.08 mm 13.00 mm or greater but
NOT exceeding 25.00 mm;
(b) 219.08 mm or greater but 12.70 mm or greater but
NOT exceeding 254.00 mm NOT exceeding 50.80 mm;
(c) 254.00 mm or greater but 19.05 mm or greater but
NOT exceeding 323.85 mm NOT exceeding 41.00 mm;
(d) 323.85 mm or greater but 25.40 mm or greater but
NOT exceeding 720.73 mm NOT exceeding 75.00 mm
Op. 01.01.2007 Dec. 08.11.2006 - TC 0614209
7304.19.00 TUBES, seamless, conforming to ALL of the following:
(a) specification API 5L-X42 OR API 5L-X60 OR API 5L-B;
(b) OD less than 153.4 mm OR greater than 482.3 mm;
(c) resistance to stepwise cracking and tested to NACE
standard TM02-84
Op. 01.01.2007 Dec. 08.11.2006 - TC 0614211
7304.19.00 PIPES, STEEL, having a diameter NOT less than 65 cm
Op. 24.01.2007 Dec. 13.04.2007 - TC 0701302
7304.19.00 LINE PIPE, seamless, to DNV-OS-F101
Op. 01.01.2007 Dec. 06.03.2007 - TC 0703467
7304.23.00 DRILL PIPE, carbon alloy steel, having BOTH of the following:
(a) tool joints attached at each end;
(b) outside diameter NOT less than 139 mm
Op. 26.09.2014 Dec. 15.12.2014 - TC 1434260
7304.23.00 DRILL RODS, rotary drilling, having ALL of the following;
(a) friction welded male AND/OR female fittings;
(b) tensile and yield strengths exceeding 200 Newtons per
square millimetre;
(c) non-uniform internal bore;
(d) not exceeding 167 millimetres in diameter
Op. 05.08.2011 Dec. 19.12.2011 - TC 1126550
7304.23.00 DRILL PIPE, seamless, non-alloy carbon steel, circular cross
section, having EITHER of the following:
(a) outside diameter (OD) NOT greater than 168.3 mm;
(b) wall thickness (WT) NOT less than 16 mm
Op. 16.08.2010 Dec. 08.11.2010 - TC 1038045
7304.23.00 DRILL PIPES, WELLBORE, seamless, having BOTH of the following:
(a) outside diameter (OD) NOT greater than 216 mm;
(b) tool joint one end
Op. 25.11.2009 Dec. 05.02.2010 - TC 0944896
7304.23.00 DRILL PIPES, having rotary connections attached, conforming to
API Specification 7, being EITHER of the following:
(a) conforming to API Specification 5D;
(b) as listed in THE TABLE
THE TABLE
Outside Diameter Wall Thickness
(i) 88 mm to 110 mm (both inclusive) 18 mm or greater;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(ii) 110 mm to 120 mm (both inclusive) 20 mm or greater;
(iii) 120 mm to 130 mm (both inclusive) 23 mm or greater
Op. 01.01.2007 Dec. 09.11.2006 - TC 0614213
7304.23.00 DRILL RODS, FRICTION WELDED, having DIN 17MnV6 steel tool joints
Op. 01.01.2007 Dec. 27.03.2007 - TC 0703471
7304.23.00 DRILL PIPE, conforming to American Petroleum Institute
Specification 5D:2001 (API 5D:2001), having rotary connection
attached
Op. 11.11.2008 Dec. 06.02.2009 - TC 0839269
7304.24.00 CASING AND/OR TUBING, STAINLESS STEEL, seamless
Op. 10.04.2008 Dec. 04.07.2008 - TC 0803235
7304.29 CASING OR TUBING, oilwell (including casing or tubing with
couplings), conforming to EITHER of the following:
(a) API Specification 5CT;
(b) Manufacturers" Material Specification CR9, CR13, CR22 or
CR25 with other requirements to API Specifications 5CT,
but NOT including EITHER of the following:
(a) plain end casing or tubing;
(b) casing with connectors
Op. 01.07.1996 Dec. 06.06.1996 - TC 9605808
7304.29 JOINTS, blast, being tubing threaded at both ends, in nominal
lengths of 3.05 m or 6.10 m
Op. 01.07.1996 Dec. 16.05.1996 - TC 9608624
7304.29.00 CASING, OIL AND/OR GAS WELL, seamless, complying with American
Petroleum Institute Standard 5L (API 5L), with OR without
connectors, having an outside diameter NOT less than 300 mm and
NOT greater than 380 mm
Op. 05.08.2014 Dec. 24.11.2014 - TC 1427032
7304.29.00 CASING OR TUBING, OIL AND/OR GAS WELL, seamless, conforming to
American Petroleum Institute Specification 5CT (API 5CT), with
OR without connectors
Op. 15.04.2013 Dec. 15.07.2013 - TC 1312751
7304.29.00 CASING OR TUBING, OIL OR GAS WELL, seamless, plain end, diameter NOT
exceeding 140 mm
Op. 30.08.1999 Dec. 08.11.1999 - TC 9906606
7304.31 TUBE, seamless, cold drawn, having an outside diameter NOT exceeding
8 mm, an inside diameter NOT exceeding 4 mm, pressure rating NOT
less than 54 900 kPa, to Specification DIN 2413
Op. 08.05.1989 Dec. 26.07.1990 - TC 8903168
7304.31 TUBES, heat exchange and condenser, seamless, cold drawn, carbon
steel, in straight lengths, ends plain, bevelled or threaded BUT
without further rework, to specification ASTM A179/A 179M-88a
Op. 10.02.1992 Dec. 16.07.1992 - TC 9201981
7304.31 TUBES, seamless, cold drawn, in straight lengths, ends plain,
bevelled or threaded, BUT without further rework, to specification
DIN standard 2391: Part 2
Op. 10.02.1992 Dec. 16.07.1992 - TC 9202044
7304.31 TUBES, carbon steel, in straight lengths, ends plain, bevelled or
threaded, BUT without further rework, conforming to ASTM A179, cold
drawn, seamless, having an OD NOT less than 6.4 mm and NOT greater
than 203.2 mm
Op. 05.03.1992 Dec. 20.07.1992 - TC 9203132
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7304.31 TUBES, cold drawn, seamless, to ANY of the following steel grades:
(a) K1006;
(b) K1016;
(c) K1010;
(d) K1020;
(e) K1026,
or ANY of the following tube specifications:
(a) JIS G3445 STKM 11-20;
(b) BS6323:Part 6:1982;
(c) ASTM A513,
and having BOTH of the following:
(a) carbon content NOT less than 0.06% and NOT greater than 0.4%
by weight;
(b) OD NOT less than 6.4 mm and NOT greater than 203.2 mm
Op. 27.07.1992 Dec. 08.10.1992 - TC 9206994
7304.31.00 WELD TEST RINGS, complying with DNV-OS-F101
Op. 08.12.2005 Dec. 03.03.2006 - TC 0516769
7304.31.00 TUBES OR HOLLOW BARS, seamless, cold drawn in straight lengths
Op. 26.11.1992 Dec. 08.03.1993 - TC 9210246
7304.39 TUBES (NOT being honed tubes), seamless, having BOTH of the
following:
(a) elevated temperature properties conforming to
Specification BS 3602 (1978) Grade 360 or AS 1835 TS 5;
(b) OD NOT less than 1 250 mm OR a WT NOT exceeding 25 mm
Op. 21.03.1985 Dec. 21.03.1985 - TC 8530426
7304.39 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths,
ends plain, bevelled or threaded in accordance with ANY of the
following tube, hollow bar or Pipe Material Specification options:
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
but without further rework, having a length NOT less than four
times the OD, as listed in THE TABLE
THE TABLE
Outside Diameter Wall Thickness
(a) NOT exceeding 219.08 mm 13.00 mm or greater but
NOT exceeding 25.00 mm;
(b) 219.08 mm or greater but 12.70 mm or greater but
NOT exceeding 254.00 mm NOT exceeding 50.80 mm;
(c) 254.00 mm or greater but 19.05 mm or greater but
NOT exceeding 323.85 mm NOT exceeding 41.00 mm;
(d) 323.85 mm or greater but 25.40 mm or greater but
NOT exceeding 720.73 mm NOT exceeding 75.00 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8735571
7304.39 TUBES, seamless, hot finished, boiler and superheater, in straight
lengths, ends plain, bevelled or threaded, BUT without further
rework, to specification ASTM A210/A 210M-88a
Op. 10.02.1992 Dec. 16.07.1992 - TC 9201980
7304.39 PIPE, seamless, hot finished, in straight lengths, ends plain,
bevelled or threaded BUT without further rework, to specification
ASTM A333/A333M-88a
Op. 10.02.1992 Dec. 16.07.1992 - TC 9202042
7304.39.00 PROCESS PIPES, seamless, carbon steel, circular cross-section,
having BOTH of the following:
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(a) square cut plain ends OR bevelled ends;
(b) compliance with American Society for Testing and Materials
standard ASTM A333/A333M - 10
Op. 21.08.2013 Dec. 11.11.2013 - TC 1328486
7304.39.00 PIPES, GYPSUM DEHYDRATION SYSTEM, iron OR non-alloy steel,
having an external diameter greater than 380 mm
Op. 23.11.2012 Dec. 03.04.2013 - TC 1245157
7304.39.00 WELD TEST RINGS, complying with DNV-OS-F101
Op. 08.12.2005 Dec. 03.03.2006 - TC 0516768
7304.39.00 PIPES, STEEL, POWER STATION STEAM GENERATION BOILER, being ANY
of the following:
(a) main and/or auxilary steam pipes;
(b) hot reheat pipes;
(c) cold reheat pipes;
(d) main feed water pipes;
(e) super heater pipes
Op. 31.08.2007 Dec. 09.11.2007 - TC 0713866
7304.39.00 HOLLOW BARS, seamless, hot rolled or hot finished in straight
lengths
Op. 22.10.1996 Dec. 06.01.1997 - TC 9611660
7304.39.00 TUBES, seamless, carbon steel, hot finished, in straight lengths,
ends plain OR bevelled OR threaded, but without further rework, to
specification DIN 1629
Op. 30.12.1996 Dec. 25.03.1997 - TC 9613286
7304.41 TUBES, stainless steel, containing 12% or more chromium, OD NOT
exceeding 3.175 mm
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341367
7304.41 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths,
ends plain, bevelled or threaded in accordance with ANY of the
following tube, hollow bar or Pipe Material Specification options:
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
but without further rework, having a length NOT less than four
times the OD, as listed in THE TABLE:
THE TABLE
Outside Dia Wall Thickness
(a) NOT exceeding 219.08 mm 13.00 mm or greater but
NOT exceeding 25.00 mm;
(b) 219.08 mm or greater but 12.70 mm or greater but
NOT exceeding 254.00 mm NOT exceeding 50.80 mm;
(c) 254.00 mm or greater but 19.05 mm or greater but
NOT exceeding 323.85 mm NOT exceeding 41.00 mm;
(d) 323.85 mm or greater but 25.40 mm or greater but
NOT exceeding 720.73 mm NOT exceeding 75.00 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8735572
7304.41 TUBES, alloy steel, in straight lengths, ends plain, bevelled
or threaded in accordance with ANY of the following Pipe
Material Specification options:
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
but without further rework, containing NOT less than 12% by
weight of chromium, having EITHER of the following:
(a) OD NOT exceeding 105 mm and WT NOT less than 4.5 mm
but NOT exceeding 25 mm;
(b) OD NOT less than 105 mm and WT NOT exceeding 25 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8801453
7304.41.00 TUBING, stainless steel, having ALL of the following:
(a) welded threaded ends;
(b) polytetrafluoroethylene (PTFE) seal;
(c) hydrogenated nitrile butadiene rubber (HNBR) o-ring;
(d) internal tube diameter of NOT less than 50 mm and
NOT greater than 60 mm
Op. 31.03.2014 Dec. 24.06.2014 - TC 1411122
7304.41.00 WELD TEST RINGS, complying with DNV-OS-F101
Op. 08.12.2005 Dec. 03.03.2006 - TC 0516767
7304.41.00 TUBES, cold reduced, stainless steel, carbon content NOT exceeding
0.03%, to specifications ASTM A790, A789
Op. 16.07.1993 Dec. 01.11.1993 - TC 9306991
7304.41.00 TUBING, seamless stainless steel, duplex alloy S.A.F.2205 to ASTM
A 789 UNS S31803, having an outside diameter less than 25mm
Op. 05.04.1993 Dec. 05.04.1993 - TC 9329022
7304.41.00 TUBE OR PIPE, stainless steel, to specification UNS S31803, having
a chemical composition by weight of ALL the following:
(a) carbon 0.030% maximum;
(b) manganese 2.00% maximum;
(c) phosphorus 0.030% maximum;
(d) sulphur 0.020% maximum;
(e) silicon 1.00% maximum;
(f) chromium 21.00 - 23.00% both inclusive;
(g) nickel 4.50 - 6.50% both inclusive;
(h) nitrogen 0.03 - 0.20% maximum;
(i) molybdenum 2.50 - 3.50% both inclusive
Op. 25.05.1994 Dec. 26.08.1994 - TC 9404855
7304.41.00 TUBES, seamless, circular cross section, stainless steel, to
specification ASTM A269 or ASTM A213, cold drawn and annealed,
whether or NOT surface finished, having BOTH of the following:
(a) OD NOT exceeding 6.35 mm;
(b) WT NOT exceeding 1.20 mm
Op. 31.07.1995 Dec. 27.10.1995 - TC 9509324
7304.41.00 TUBES OR PIPES, stainless steel, seamless
Op. 25.11.2003 Dec. 08.03.2004 - TC 0314979
7304.49 TUBES, stainless steel, containing 12% or more chromium, OD NOT
exceeding 3.175 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8635310
7304.49 TUBES, alloy steel, in straight lengths, ends plain, bevelled
or threaded in accordance with ANY of the following Pipe
Material Specification options:
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
but without further rework, containing NOT less than 12% by
weight of chromium, having EITHER of the following:
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but
NOT exceeding 25.0 mm;
(b) OD NOT less than 105 mm and WT NOT exceeding 25 mm
Op. 03.07.1987 Dec. 04.09.1987 - TC 8734525
7304.49 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths,
ends plain, bevelled or threaded in accordance with ANY of the
following tube, hollow bar or Pipe Material Specification options:
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
but without further rework, having a length NOT less than four
times the OD, as listed in THE TABLE:
THE TABLE
Outside Dia Wall Thickness
(a) NOT exceeding 219.08 mm 13.00 mm or greater but
NOT exceeding 25.00 mm;
(b) 219.08 mm or greater but 12.70 mm or greater but
NOT exceeding 254.00 mm NOT exceeding 50.80 mm;
(c) 254.00 mm or greater but 19.05 mm or greater but
NOT exceeding 323.85 mm NOT exceeding 41.00 mm;
(d) 323.85 mm or greater but 25.40 mm or greater but
NOT exceeding 720.73 mm NOT exceeding 75.00 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8735573
7304.49.00 TUBING OR PIPING, seamless stainless steel, having extruded
aluminium finning
Op. 20.07.2009 Dec. 02.10.2009 - TC 0925796
7304.49.00 WELD TEST RINGS, complying with DNV-OS-F101
Op. 08.12.2005 Dec. 03.03.2006 - TC 0516766
7304.49.00 PIPES, stainless steel, seamless, bevelled OR plain ends
Op. 29.07.1999 Dec. 15.10.1999 - TC 9905670
7304.49.00 TUBES OR PIPES, stainless steel, seamless
Op. 25.11.2003 Dec. 08.03.2004 - TC 0314980
7304.51 TUBES, longitudinally finned, extruded
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341428
7304.51 PIPE, seamless, cold drawn, in straight lengths, ends plain,
bevelled or threaded BUT without further rework, to specification
ASTM A333/A 333M-88a
Op. 10.02.1992 Dec. 16.07.1992 - TC 9202040
7304.51 PIPE, seamless, ferritic alloy steel, cold drawn, in straight
lengths, ends plain, bevelled or threaded BUT without further
rework, to specification ASTM A335/A 335M-89a
Op. 10.02.1992 Dec. 16.07.1992 - TC 9202045
7304.51.00 TUBES, threaded, seamless, cold-drawn, having ALL of the
following;
(a) outside diameter NOT greater than 39 mm;
(b) inside diameter NOT greater than 27.6 mm;
(c) length NOT greater than 2.6 m
Op. 19.05.2009 Dec. 14.08.2009 - TC 0916934
7304.51.00 WELD TEST RINGS, complying with DNV-OS-F101
Op. 08.12.2005 Dec. 03.03.2006 - TC 0516770
7304.51.00 TUBES, seamless alloy steel, cold drawn, compliant with American
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Society for Testing and Materials Standard A519/4130 (ASTM
A519/4130)
Op. 29.02.2008 Dec. 16.05.2008 - TC 0803409
7304.51.00 TUBES OR HOLLOW BARS, seamless, alloy steel, cold rolled or cold
finished, in straight lengths
Op. 17.06.1993 Dec. 24.09.1993 - TC 9304563
7304.59 TUBES OR PIPES, seamless, tested and certified to EITHER of the
following Specifications:
(a) ASTM A200 Grade T5;
(b) ASTM A335 Grade P5
Op. 01.01.1988 Dec. 01.01.1988 - TC 8801707
7304.59 TUBES, alloy steel, in straight lengths, ends plain, without
further rework, to ANY of the following Material Specifications:
(a) ASTM A213;
(b) ASME A213;
(c) BS 3059;
(d) AS 1835,
having ALL of the following:
(a) chromium content, by weight, of 0.7% or greater but NOT
exceeding 12.5%;
(b) an OD of 30 mm or greater but NOT exceeding 127 mm;
(c) WT NOT exceeding 12.5 mm
Op. 16.10.1989 Dec. 02.01.1990 - TC 8907466
7304.59 TUBES, boiler, hot finished, seamless ferritic alloy steel, in
straight lengths, ends plain, bevelled or threaded, BUT without
further rework, to specification ASTM A213/A213M-89a
Op. 10.02.1992 Dec. 23.07.1992 - TC 9201989
7304.59 PIPE, seamless ferritic alloy steel, hot finished, in straight
lengths, ends plain, bevelled or threaded BUT without further
rework, to specification ASTM A335/A 335M-88a
Op. 10.02.1992 Dec. 16.07.1992 - TC 9201999
7304.59 PIPE, seamless, hot finished, in straight lengths, ends plain,
bevelled or threaded BUT without further rework to specification
ASTM A333/A 333M-88a
Op. 10.02.1992 Dec. 16.07.1992 - TC 9202039
7304.59.00 PROCESS PIPES, seamless, carbon steel, circular cross-section,
having BOTH of the following:
(a) square cut plain ends OR bevelled ends;
(b) compliance with American Society for Testing and Materials
standard ASTM A 106/A 106M - 06a OR ASTM A106/A106M - 08
Op. 21.08.2013 Dec. 19.11.2013 - TC 1328488
7304.59.00 TUBES, seamless, alloy steel, forged, in straight lengths,
having ALL of the following:
(a) length NOT greater than 1 950 mm;
(b) outside diameter (OD) NOT greater than 550 mm;
(c) wall thickness (WT) NOT less than 70 mm
Op. 17.11.2009 Dec. 22.01.2010 - TC 0943497
7304.59.00 WELD TEST RINGS, complying with DNV-OS-F101
Op. 08.12.2005 Dec. 03.03.2006 - TC 0516771
7304.59.00 PIPES, STEEL, POWER STATION STEAM GENERATION BOILER, being ANY
of the following:
(a) main steam pipes;
(b) hot reheat pipes;
(c) cold reheat pipes;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(d) main feed water pipes
Op. 28.12.2007 Dec. 24.05.2008 - TC 0800039
7304.59.00 RODS, RAISE DRILL, alloy steel, integral
Op. 28.04.2008 Dec. 18.07.2008 - TC 0805489
7304.59.00 TUBES, seamless, carbon steel, hot finished in straight lengths,
ends plain, bevelled or threaded, but without further rework, to
specification AISI 4140 quenched and tempered
Op. 09.12.1992 Dec. 30.08.1993 - TC 9310300
7304.59.00 BARS, hollow, to specification AISI 4145H modified
Op. 18.04.1994 Dec. 22.07.1994 - TC 9404209
7304.59.00 TUBES OR PIPES, seamless, conforming to EITHER of the following
specifications:
(a) SA-213 T22;
(b) SA-335 P22
Op. 01.11.1996 Dec. 31.01.1997 - TC 9611933
7304.59.00 DRILL STRING SECTIONS, THREADED, ROTARY PERCUSSIVE ROCK DRILLING,
being ANY of the following:
(a) hollow drill tube;
(b) hollow bar and rod external cross section dimension exceeding
52 mm, and a maximum internal dimension greater than one half
of the maximum external cross section dimension
Op. 16.05.1997 Dec. 01.08.1997 - TC 9704455
7304.59.00 TUBES OR PIPES, seamless alloy steel, hot finished, to ASTM A519
Grade 4140
Op. 08.01.1998 Dec. 13.03.1998 - TC 9800163
7304.59.00 DRILL RODS, ROTARY PERCUSSIVE ROCK DRILLING, hollow, threaded OR
tapered, external cross-section dimension exceeding 52 mm
Op. 10.08.1998 Dec. 16.10.1998 - TC 9807063
7304.59.00 TUBES, hot rolled, seamless alloy steel to specification DIN1629
Op. 19.11.1999 Dec. 31.01.2000 - TC 9908842
7304.59.00 LANCES, OXYGEN OR INERT GAS, ceramic coated
Op. 08.12.2000 Dec. 02.03.2001 - TC 0010030
7304.59.00 TUBES OR HOLLOW BARS, seamless, alloy steel, hot finished OR hot
rolled, in straight lengths
Op. 09.11.2004 Dec. 21.01.2005 - TC 0411761
7305.11.00 LINE PIPE, OIL AND GAS, complying with American
Petroleum Institute (API) Standard, Specification 5L, Grade B,
Production Specification Level (PSL) 1, having ALL of the
following:
(a) varnish coatings;
(b) length NOT less than 12 metres;
(c) bevelled ends;
(d) wall thickness NOT less than 9 mm and NOT greater than 13
mm;
(e) outside diameter NOT less than 640 mm and NOT greater than
800 mm;
(f) longitudinally submerged arc welding;
but NOT including spirally submerged arc welded steel line pipe
complying with Australian Standard AS 1579
Op. 10.04.2007 Dec. 12.09.2007 - TC 0705206
7305.11.00 PIPE, SUBMERGED ARC WELDED (SAW), having EITHER of the following:
(a) outside diameter NOT less than 750 mm;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(b) wall thickness NOT less than 9.53 mm
Op. 27.08.2008 Dec. 09.02.2009 - TC 0828344
7305.11.00 LINE PIPE, submerged arc welded, to DNV-OS-F101
Op. 04.11.2004 Dec. 01.02.2005 - TC 0411588
7305.12.00 STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE
WELDED, exceeding 406.4 mm external diameter, conforming to
American Petroleum Institute Specification 5L (API 5L)
Op. 20.07.2012 Dec. 08.11.2012 - TC 1241575
7305.12.00 LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with
American Petroleum Institute Standard Specification 5L (API 5L)
Op. 20.07.2012 Dec. 10.10.2012 - TC 1224027
7305.12.00 LINE PIPE, ELECTRIC RESISTANCE WELDED(ERW), complying with
American Petroleum Institute standard API Specification 5L,
grade X65, having BOTH of the following:
(a) outside diameter (OD) NOT less than 508 mm;
(b) wall thickness (WT) NOT less than 19.1 mm
Op. 14.04.2011 Dec. 11.07.2011 - TC 1112481
7305.12.00 PIPE, ELECTRIC RESISTANCE WELDED, exceeding EITHER of the
following:
(a) outside diameter 508 mm;
(b) wall thickness 12.7 mm
Op. 20.02.2008 Dec. 18.03.2010 - TC 1013309
7305.12.00 LINE PIPE, OIL AND GAS PIPELINE, steel, having BOTH of the
following:
(a) diameter NOT less than 645 mm;
(b) longitudinally welded
Op. 23.04.2007 Dec. 16.07.2007 - TC 0705875
7305.12.00 LINE PIPE, OIL AND GAS, stainless steel, welded, having an
external diameter NOT less than 406.4 mm
Op. 31.07.2008 Dec. 24.10.2008 - TC 0824211
7305.12.00 STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE
WELDED, exceeding 406.4 mm external diameter, conforming to
American Petroleum Institute Specification 5L (API 5L)
Op. 20.07.2012 Dec. 08.11.2012 - TC 1241575
7305.19.00 PIPE SPOOLS, EXPANSION LOOP, stainless steel, having an outside
diameter greater than 406.4 mm
Op. 18.11.2013 Dec. 10.02.2014 - TC 1338995
7305.19.00 PIPE, SUBMERGED ARC WELDED (SAW), helical, having BOTH of the
following:
(a) outside diameter NOT less than 750 mm;
(b) wall thickness NOT less than 9.53 mm
Op. 21.12.2011 Dec. 02.04.2012 - TC 1142287
7305.20.00 CASING, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE WELDED,
conforming to American Petroleum Institute Specification 5CT
(API 5CT) with OR without connectors, external diameter
exceeding 406.4 mm
Op. 20.07.2012 Dec. 08.11.2012 - TC 1241578
7305.20.00 CASING, OIL AND/OR GAS WELL, electric resistance welded,
conforming to American Petroleum Institute Specification 5CT
(API 5CT), with OR without connectors
Op. 20.07.2012 Dec. 31.10.2012 - TC 1241541
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7305.20.00 CASING, OIL AND/OR GAS WELL, having BOTH of the following:
(a) outside diameter NOT less than 500 mm;
(b) wall thickness NOT less than 14 mm
Op. 26.03.2012 Dec. 18.06.2012 - TC 1209900
7305.20.00 CASING, electric resistance welded, conforming to American
Petroleum Institute Specification 5CT (API 5CT), Grades C-75 OR
L-80 OR N-80 OR C-90 OR C-95 OR S-95 OR T-95 OR P-110 OR Q-125
OR V-150, with OR without connectors, having BOTH of the
following:
(a) nominal outside diameter NOT less than 508 mm;
(b) wall thickness NOT less than 12.7 mm
Op. 21.05.2010 Dec. 17.08.2010 - TC 1022968
7305.20.00 CONDUCTOR CASING, OILWELL, to API specification 5L, with OR
without connectors, having BOTH of the following:
(a) outside diameter exceeding 500 mm;
(b) wall thickness exceeding 20 mm
Op. 30.07.1998 Dec. 23.10.1998 - TC 9806755
7305.31 TUBES, alloy steel, in straight lengths, ends plain, bevelled
or threaded in accordance with ANY of the following Pipe
Material Specification options:
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
but without further rework, containing NOT less than 10% by
weight of chromium, having EITHER of the following:
(a) OD NOT less than 1 250 mm;
(b) WT 5 mm or greater but NOT exceeding 25 mm
Op. 03.07.1987 Dec. 04.09.1987 - TC 8734523
7305.31.00 PIPE MODULES, steel frame, being pipework fitted rigid
framework, having BOTH the following:
(a) length NOT less than 2.5 metres;
(b) weight NOT less than 3 tonnes
Op. 31.08.2015 Dec. 09.12.2015 - TC 1533597
7305.31.00 PIPES, electric resistance welded, circular cross-section, non-
alloy steel, complying with Australian and New Zealand Standard
1163:2009 (AS/NZS 1163:2009), Grade C450L0, having ALL of
the following:
(a) length NOT less than 9 m and NOT greater than 18.15 m;
(b) outside diameter 457 mm;
(c) wall thickness NOT less than 5.2 mm and NOT greater than
11 mm;
(d) bevelled ends;
(e) non-alloy steel complying with Japanese Industrial
Standard G 3474:2008 (JIS G 3474:2008), Grade STKT590
For the purposes of this Order, tolerances allowable for
specification (b) are +/- 5%.
Op. 07.01.2014 Dec. 07.04.2014 - TC 1400827
7305.31.00 PIPES, mild steel OR stainless steel, with OR without couplings,
having BOTH of the following:
(a) internal ceramic tile lining;
(b) outside diameter greater than 406.4 mm
Op. 21.03.2011 Dec. 15.06.2011 - TC 1109648
7305.31.00 TUBES, stainless steel, straight seam welded, conforming to
American Society of Testing and Materials Standards
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
A-312/A 312M - 09 (ASTM A-312/A 312M - 09) and
A358/A 358M - 08a (ASTM A358/A 358M - 08a), having ALL of the
following:
(a) straight lengths;
(b) ends plain or bevelled or threaded or grooved;
(c) wall thickness (WT) NOT less than 4 mm;
(d) containing NOT less than 10% by weight of chromium
Op. 01.07.2010 Dec. 29.09.2010 - TC 1029727
7305.31.00 WELD TEST RINGS, complying with Offshore Standard for Submarine
Pipeline Systems DNV-OS-F101
Op. 08.12.2005 Dec. 08.03.2006 - TC 0604839
7305.39.00 WELD TEST RINGS, complying with DNV-OS-F101
Op. 08.12.2005 Dec. 03.03.2006 - TC 0516772
7306.19.00 TIE-IN SPOOLS, SUBSEA, having longitudinally welded line
pipe, complying with Det Norske Veritas Offshore Standard F101
(DNV-OS-F101), with OR without ANY of the following:
(a) anodes;
(b) coating AND/OR cladding AND/OR lining;
(c) bends;
(d) crosses;
(e) flanges;
(f) elbows;
(g) tees;
(h) reducers;
(i) protective casings
Op. 12.10.2015 Dec. 13.01.2016 - TC 1537985
7306.19.00 RISERS, OIL AND/OR GAS, rigid, complying with Det Norske Veritas
Offshore Standard F101 (DNV-OS-F101), whether OR not clad AND/OR
coated, with OR without ANY of the following:
(a) centralisers;
(b) fittings;
(c) seals
Op. 01.10.2015 Dec. 06.01.2016 - TC 1536922
7306.19.00 LINE PIPE, High Frequency Welded (HFW), duel layer fusion bonded
epoxy coated, complying with American Petroleum Institute
Standard Specification 5L (API 5L), having ALL of the following:
(a) steel AND pipe grade X65M;
(b) product specification PSL2;
(c) diameter being EITHER of the following:
(i) NOT exceeding 55 mm;
(ii) exceeding 168.3 mm
Op. 22.05.2015 Dec. 10.08.2015 - TC 1519289
7306.19.00 LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with
American Petroleum Institute Standard Specification 5L (API 5L)
and International Standard 3183,(ISO 3183), having a diameter
exceeding 168.3 mm
Op. 18.12.2012 Dec. 18.03.2013 - TC 1248298
7306.19.00 STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE
WELDED, conforming to American Petroleum Institute Specification
5L (API 5L) having EITHER of the following:
(a)external diameter NOT greater than 33.7 mm;
(b)external diameter NOT less than 168.3 mm and NOT greater than
406.4 mm.
Op. 15.11.2012 Dec. 17.12.2012 - TC 1248095
7306.19.00 LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
American Petroleum Institute Standard Specification 5L (API 5L),
having EITHER of the following:
(a) diameter less than 33.7 mm;
(b) diameter exceeding 168.3 mm
Op. 20.07.2012 Dec. 12.11.2012 - TC 1224029
7306.19.00 PIPE, ELECTRIC RESISTANCE WELDED, exceeding a wall thickness of
12.7 mm
Op. 22.02.2008 Dec. 20.11.2009 - TC 0943624
7306.19.00 PIPE, to specification API 5L Grade B, ASTM 53B, being ANY of the
following sizes (+/- 10%):
(a) OD 114.3 mm, WT 6.0 mm;
(b) OD 88.9 mm, WT 5.5 mm;
(c) OD 60.3 mm, WT 3.9 mm
Op. 01.01.2007 Dec. 09.11.2006 - TC 0614217
7306.19.00 LINE PIPE, complying with DNV-OS-F101
Op. 01.01.2007 Dec. 02.01.2007 - TC 0614760
7306.19.00 PIPES, WELDED, complying with American Petroleum Institute
Standard Specification of Line Pipe 5L, comprising ALL of the
following:
(a) outside diameter NOT less than 63 mm and NOT greater than
115 mm;
(b) wall thickness NOT less than 4 mm and NOT greater than 11
mm;
(c) yield strength capacity NOT less than 385 MPa
Op. 26.02.2007 Dec. 18.05.2007 - TC 0703024
7306.19.00 TUBES OR PIPES, ERW, bevelled ends, certified to ALL the following
specifications:
(a) AS 1163;
(b) API 5L grades B and X42;
(c) ASTM A53 grade B;
in ANY of the following sizes:
Cross Section Diameter Wall Thickness Length
NOT less than 88.5 mm and NOT less than 4 mm and NOT less than
NOT greater than 90 mm NOT greater than 10 mm 6 m
NOT less than 114 mm and NOT less than 4 mm and NOT less than
NOT greater than 115 mm NOT greater than 10 mm 6 m
NOT less than 141 mm and NOT less than 4 mm and NOT less than
NOT greater than 142 mm NOT greater than 10 mm 6 m
Op. 06.11.2003 Dec. 23.10.2008 - TC 0835803
7306.29.00 CASING, OIL AND/OR GAS WELL, electric resistance welded,
conforming to American Petroleum Institute Specification 5CT
(API 5CT), with OR without connectors
Op. 20.07.2012 Dec. 31.10.2012 - TC 1241536
7306.29.00 TUBING, electrical resistance welded, coiled OR in spools, having
BOTH of the following:
(a) minimum continuous length of 2 000 m;
(b) minimum OD of 31 mm
Op. 01.01.2007 Dec. 09.11.2006 - TC 0614219
7306.29.00 CASING, Electric Resistance Welded (ERW), complying with
American Petroleum Institute 5CT (API 5CT) having BOTH of the
following:
(a) outside diameter of 406.4mm;
(b) wall thickness exceeding 10 mm but NOT exceeding 14 mm
For the purposes of this Order, tolerances of + or - 1% are
allowable for the specification in (a)
Op. 01.01.2007 Dec. 29.11.2006 - TC 0614773
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7306.30 PIPES, lance, oxygen calorised and ceramic coated
Op. 22.08.1991 Dec. 25.05.1992 - TC 9107706
7306.30 TUBES, ERW boiler, being EITHER carbon or carbon manganese steel,
in straight lengths, ends plain, bevelled or threaded, BUT without
further rework, to specification ASTM A178/A 178M-89
Op. 10.02.1992 Dec. 16.07.1992 - TC 9201983
7306.30 TUBES, cold drawn, welded, to specification ASTM A513,
having BOTH of the following:
(a) OD NOT less than 203.2mm and NOT greater than 306.0mm;
(b) carbon content NOT less than 0.06% and NOT greater than
0.4% by weight
Op. 04.09.1992 Dec. 31.12.1992 - TC 9208087
7306.40.00 TUBES OR PIPES, welded, stainless steel in accordance with
EN10217-7TC1 OR EN 10296-2, having an outer diameter exceeding
18.0 mm and NOT exceeding 1 012.0 mm
Op. 26.10.2015 Dec. 18.01.2016 - TC 1539887
7306.30.00 TUBES, cold drawn, stress relieved, cylindrical, electric
resistance welded drawn over mandrel, non-alloy grade E355+SR,
standard EN 10305-2, having BOTH of the following:
(a) straightness of 1 mm/1000 mm of the length;
(b) internal diameter NOT less than 25.4 mm and NOT greater
than 228.6 mm
with OR without fitted end caps
Op. 20.10.2015 Dec. 13.01.2016 - TC 1539396
7306.30.00 TUBES, cold drawn, cylindrical, electric resistance welded drawn
over mandrel, non-alloy steel grade E355+C,
standard EN 10305-2, having BOTH of the following:
(a) straightness of 1 mm/1000 mm of the length;
(b) internal diameter NOT less than 25.4 mm and NOT greater
than 110.0 mm
with OR without fitted end caps
Op. 20.10.2015 Dec. 13.01.2016 - TC 1539395
7306.30.00 PIPE MODULES, rigid steel frame, having flanged pipework, pipe
diameter NOT greater than 450 mm
Op. 01.10.2015 Dec. 14.12.2015 - TC 1536918
7306.30.00 COILED TUBING, OIL AND GAS WELL, whether OR not on spools AND/OR
reels
Op. 20.12.2013 Dec. 20.03.2014 - TC 1409618
7306.30.00 PIPES, mild steel, with OR without couplings, having BOTH of the
following:
(a) internal ceramic tile lining;
(b) outside diameter less than 406.4 mm
Op. 28.02.2011 Dec. 06.06.2011 - TC 1107493
7306.30.00 PIPES, welded steel, multilayer, having ALL of the following:
(a) steel inner service pipe;
(b) polyurethane foam insulation incorporating copper wires;
(c) high density polyethylene outer casing
Op. 07.06.2010 Dec. 30.08.2010 - TC 1025391
7306.30.00 TUBES, welded, complying with Japanese Industrial Standard G3445
STK11A (JIS G3445 STKM11A), having an outside diameter NOT
greater than 12 mm
Op. 07.02.2007 Dec. 20.04.2007 - TC 0701959
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7306.30.00 TUBES OR PIPES, ERW, conforming to specification SA 178
Op. 01.11.1996 Dec. 20.01.1997 - TC 9611935
7306.30.00 TUBES, cold drawn, welded, stress relieved, to DIN specification
2393, having ALL of the following:
(a) outside diameter of 15 mm to 22 mm;
(b) inside diameter of 13 mm to 19 mm;
(c) wall thickness of 1 mm to 1.6 mm
Op. 16.04.2002 Dec. 05.07.2002 - TC 0203211
7306.30.00 TUBES, WELDED, non alloy steel, being EITHER of the following:
(a) single wall resistance welded to specification SAE J526,
having ALL of the following:
(i) carbon content NOT greater than 0.13%;
(ii) outside diameter NOT greater than 11.50 mm;
(iii) wall thickness NOT less than 0.5 mm and NOT greater
than 1.0 mm;
(b) double wall copper brazed to specification SAE J527,
having ALL of the following:
(i) carbon content NOT greater than 0.13%;
(ii) outside diameter NOT greater than 13 mm;
(iii) wall thickness NOT less than 0.5 mm and NOT greater
than 1.0 mm
Op. 31.03.2003 Dec. 27.06.2003 - TC 0303383
7306.40 TUBES, stainless steel, longitudinally welded, having BOTH of the
following dimensions:
(a) an OD 105 mm or greater but NOT exceeding 220 mm;
(b) a WT 1.50 mm or greater but NOT exceeding 5.00 mm
Op. 30.04.1985 Dec. 05.09.1985 - TC 8531977
7306.40 TUBES, alloy steel, in straight lengths, ends plain, bevelled
or threaded in accordance with ANY of the following Pipe
Material Specification options:
(a) AS;
(b) ASME;
(c) ASTM;
(d) BS;
(e) DIN,
but without further rework, containing NOT less than 12% by
weight of chromium, having EITHER of the following:
(a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but NOT
exceeding 25.0 mm;
(b) OD NOT less than 105 mm and WT NOT exceeding 25 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8733276
7306.40.00 PIPE MODULES, rigid steel frame, having flanged pipework, pipe
diameter NOT greater than 450 mm
Op. 01.10.2015 Dec. 14.12.2015 - TC 1536919
7306.40.00 TUBES, stainless steel, spiral welded, having ALL of the
following:
(a) outside diameter NOT less than 105 mm and NOT greater
than 220 mm;
(b) wall thickness NOT less than 1.50 mm and NOT greater than
7.00 mm;
(c) SAE International grade 409 OR grade 410L
Op. 28.07.2015 Dec. 30.10.2015 - TC 1529367
7306.40.00 PIPES, stainless steel, press fit, having ALL of the following:
(a) ethylene propylene diene monomer(EPDM) rubber seal;
(b) stainless steel OR gunmetal press connector;
(c) outside diameter NOT less than 12 mm and NOT greater
than 54 mm
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 15.01.2015 Dec. 08.04.2015 - TC 1502400
7306.40.00 PIPES, stainless steel, press fit, having ALL of the following:
(a) ethylene propylene diene (EPDM) rubber seal;
(b) stainless steel OR gunmetal press connector;
(c) outside diameter NOT less than 12 mm and NOT greater than
108 mm
Op. 15.01.2015 Dec. 15.04.2015 - TC 1502401
7306.40.00 PRESSURE TUBING, stainless steel, wound on spools OR reels,
having ALL of the following:
(a) wall thickness NOT greater than 1.70 mm;
(b) outer diameter NOT greater than 14.00 mm;
(c) fluorinated ethylene propylene (FEP) protective outer pipe
cover
Op. 27.08.2014 Dec. 17.11.2014 - TC 1430285
7306.40.00 HYDRAULIC CONTROL LINES, OIL AND/OR GAS WELL EQUIPMENT, wound on
spools OR reels, including BOTH of the following:
(a) NOT less than 2 stainless steel pipes, having BOTH of the
following:
(i) pipe wall thickness NOT greater than 1.36 mm;
(ii) pipe outer diameter NOT less than 5.70 mm and NOT
greater than 6.90 mm,
(b) ethylene tetrafluoroethylene (ETFE) protective cover
Op. 20.06.2014 Dec. 10.09.2014 - TC 1421009
7306.40.00 TUBES OR PIPES, stainless steel, longitudinal welded, in
straight lengths, conforming to EITHER of the following
specifications:
(a) American Society for Testing and Materials (ASTM)
specifications A249 OR A268 OR A269 OR A270 OR A554 OR
A688 OR A789;
(b) Australian Standard 1528 (AS 1528)
Op. 06.02.2014 Dec. 05.05.2014 - TC 1405087
7306.40.00 TUBES OR PIPES, stainless steel, welded, in straight
lengths, conforming to ANY of the following American
Society for Testing and Materials (ASTM) specifications:
(a) A312;
(b) A358;
(c) A409;
(d) A778;
(e) A790;
(f) A813;
(g) A814;
(h) A928;
(i) A999
Op. 23.12.2013 Dec. 17.03.2014 - TC 1342173
7306.40.00 PIPES, stainless steel, having ALL of the following:
(a) outside diameter NOT less than 10.3 mm and NOT greater
than 406.4 mm;
(b) wall thickness NOT less than 1.24 mm and NOT greater than
33.32 mm;
(c) compliance with American Society for Testing and Materials
standards Designations: ASTM A269-10 OR
ASTM A312/A312M - 11 OR ASTM A554-13
Op. 03.10.2013 Dec. 13.01.2014 - TC 1333366
7306.40.00 TUBES AND/OR PIPES, stainless steel, longitudinal welded, rolled
seam, having ALL of the following:
(a) outside diameter NOT less than 10 mm and NOT greater than
219 mm;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(b) wall thickness NOT less than 1 mm and NOT greater than
2.6 mm;
(c) conforming to American Iron and Steel Institute
specifications 304 OR 316L (AISI 304 OR AISI 316L)
Op. 08.07.2013 Dec. 02.10.2013 - TC 1323026
7306.40.00 PIPES, stainless steel, with OR without couplings, having BOTH
of the following:
(a) internal ceramic tile lining;
(b) outside diameter less than 406.4 mm
Op. 21.03.2011 Dec. 15.06.2011 - TC 1109650
7306.40.00 TUBES OR PIPES, stainless steel, to specification UNS S31803, having
chemical composition by weight of ALL the following:
(a) carbon : 0.030% maximum;
(b) manganese : 2.00% maximum;
(c) phosphorus : 0.030% maximum;
(d) sulphur : 0.020% maximum;
(e) silicon : 1.00% maximum;
(f) chromium : 21.00 - 23.00% both inclusive;
(g) nickel : 4.50 - 6.50% both inclusive;
(h) nitrogen : 0.03 - 0.20% maximum;
(i) molybdenum : 2.50 - 3.50% both inclusive
Op. 06.06.1994 Dec. 09.09.1994 - TC 9405021
7306.50.00 TUBES, ERW, aluminized, type JIS G3445, having ALL of the following:
(a) 12.7 mm OD;
(b) 1.6 mm WT;
(c) 5 700 mm mill length
Op. 14.04.1994 Dec. 29.07.1994 - TC 9404172
7306.61.00 TUBES, square OR rectangular, electric resistance welded,
complying with Australian/New Zealand Standard 1163:2009 (AS/NZS
1163:2009), Grade C350L0 OR C450L0, with a perimeter NOT less
than 1 050 mm and having EITHER (a) OR (b) as follows:
(a) silicon content plus 2.5 times the phosphorus content
NOT greater than 0.09%;
(b) silicon content greater than 0.14% and NOT greater than
0.24%
Op. 16.02.2016 Dec. 16.03.2016 - TC 1609617
7306.61.00 TUBES, square OR rectangular, electric resistance welded,
complying with Australian/New Zealand Standard 1163:2009 (AS/NZS
1163:2009), Grade C350L0 OR C450L0, having EITHER (a) OR (b) AND
(c), as follows:
(a) silicon content plus 2.5 times the phosphorus content
NOT greater than 0.09%;
(b) silicon content greater than 0.14% and NOT greater than
0.24%;
(c) perimeter NOT less than 1 050 mm
Op. 16.02.2016 Dec. 16.03.2016 - TC 1609618
7306.61.00 TUBES OR PIPES, stainless steel, square OR rectangular cross
section, longitudinal welded in straight lengths, conforming to
American Society for Testing and Materials A554 (ASTM A554)
specification
Op. 06.02.2014 Dec. 05.05.2014 - TC 1405088
7306.61.00 TUBES, rectangular, stainless steel, NOT less than 100 mm x 50 mm
across the flat dimensions
Op. 01.01.2007 Dec. 09.11.2006 - TC 0614222
7306.61.00 TUBES, square, stainless steel, NOT less than 100 mm x 100 mm across
the flat dimension
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 01.01.2007 Dec. 09.11.2006 - TC 0614223
7306.61.00 TUBES, square or rectangular, stainless steel to grade 1.4003,
having BOTH of the following:
(a) width NOT greater than 105 mm;
(b) wall thickness NOT greater than 4 mm
Op. 22.10.2008 Dec. 27.02.2009 - TC 0836453
7306.69.00 TUBES OR PIPES, stainless steel, longitudinal welded in straight
lengths, conforming to American Society for Testing and
Materials A554 (ASTM A554) specification, being ANY of the
following cross sections:
(a) oval;
(b) slotted;
(c) triangular;
(d) D section;
(e) tear drop
Op. 06.02.2014 Dec. 05.05.2014 - TC 1405089
7306.69.00 TUBES, cold drawn, carbon steel, hollow frame profile, having
ANY of the following sectional dimensions:
Length Width Wall Thickness
(a) 90 mm 41 mm 2.0 mm;
(b) 104 mm 43 mm 2.5 mm;
(c) 104 mm 43 mm 3.0 mm
Op. 01.01.2007 Dec. 08.05.2007 - TC 0705891
7307.11.00 FITTINGS, TUBE AND PIPE, rolled grooved, galvanised OR painted,
with OR without gaskets, being ANY of the following:
(a) elbows;
(b) couplings;
(c) reducers;
(d) adaptors;
(e) tees;
(f) caps;
(g) crosses;
(h) reducing tees;
(i) grooved flanges;
(j) adaptor flanges
Op. 19.08.2014 Dec. 10.11.2014 - TC 1429119
7307.11.00 FITTINGS, TEE SHAPED, TUBE OR PIPE JOINT, iron, threaded,
galvanised OR painted, including ALL of the following:
(a) outlet housing, with OR without gaskets;
(b) bolts AND/OR U shaped bolts;
(c) nuts
Op. 19.08.2014 Dec. 10.11.2014 - TC 1429120
7307.11.00 FITTINGS, PIPE, cast iron, non-combustible, non-flammable,
complying with European Standard EN 877:1999 (EN 877:1999)
Op. 13.10.2006 Dec. 22.12.2006 - TC 0615826
7307.11.00 COUPLINGS, CLAW, cast iron
Op. 22.04.2008 Dec. 18.07.2008 - TC 0804812
7307.11.00 FITTINGS, ELBOWS AND/OR TEES, painted roll, grooved
Op. 09.09.2008 Dec. 28.11.2008 - TC 0830239
7307.19 FITTINGS, pipe, buttweld, socketweld or threaded, being EITHER of
the following:
(a) manufactured from ASTM A-216 WCB carbon steel castings;
(b) manufactured from ASTM A-148 GR 60-90 steel castings
Op. 18.02.1985 Dec. 23.07.1985 - TC 8530530
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7307.19.00 COUPLINGS, CLAW, cast stainless steel, with OR without locking
pins, having ALL of the following:
(a) diameter NOT less than 10 mm and NOT greater than 50 mm;
(b) threaded male OR threaded female OR hose end connections;
(c) bellows seals
Op. 23.11.2015 Dec. 03.03.2016 - TC 1608634
7307.19.00 FITTINGS, PIPE AND/OR TUBE, malleable cast iron, reducing OR non-
reducing, being ANY of the following:
(a) tees;
(b) combination tees and crosses;
(c) corners;
(d) crosses;
(e) cross sets;
(f) crossovers;
(g) elbows;
(h) flanges;
(i) sockets;
(j) side palms;
(k) supports;
(l) swivels;
(m) couplings;
(n) hooks;
(o) collars;
(p) collar plates;
(q) hinges;
(r) panel clips;
(s) bases;
(t) base plates
Op. 29.09.2010 Dec. 20.12.2010 - TC 1044234
7307.19.00 FITTINGS, PIPE, ductile cast iron
Op. 10.04.2008 Dec. 20.06.2008 - TC 0803227
7307.19.00 FITTINGS, CAMLOCK, stainless steel, being ANY of the following:
(a) male sections and/or female sections;
(b) plugs;
(c) caps
Op. 22.04.2008 Dec. 18.07.2008 - TC 0804811
7307.19.00 COUPLINGS, flexible, cast, stainless steel, having internal
rubber gaskets
Op. 29.10.2008 Dec. 16.01.2009 - TC 0837499
7307.19.00 PIPE FITTINGS, roll grooved or shouldered, being ANY of the
following:
(a) elbows;
(b) tees;
(c) reducers;
(d) end caps;
(e) adapters
Op. 04.12.2008 Dec. 27.02.2009 - TC 0842803
7307.19.00 FITTINGS, pipe, malleable cast iron
Op. 28.04.1993 Dec. 30.07.1993 - TC 9305440
7307.19.00 FITTINGS, pipe, B.S.P thread, made of galvanised malleable iron, to
BS 1256, being ANY of the following:
(a) elbows, 90 degrees, being EITHER, female to female, or male to
female;
(b) elbows, 45 degrees, being female to female;
(c) elbows, 3 way;
(d) elbows, reducing, 90 degrees;
(e) tees, including 4 way, and reducing tees;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(f) bush, hexagon;
(g) caps;
(h) crosses;
(i) backnuts;
(j) nipples, being ANY of the following:
(i) hexagon;
(ii) barrel;
(iii) plain;
(iv) reducing;
(k) sockets including reducing sockets;
(l) plugs, square head;
(m) bends, 90 degrees, EITHER, male to female, or female to
female;
(n) bends, 45 degrees, male to female;
(o) unions, EITHER, male to female, or female to female
Op. 06.07.1993 Dec. 08.10.1993 - TC 9306802
7307.19.00 PIPE FITTINGS, POTABLE WATER AND GAS LINES, being EITHER of the
FOLLOWING:
(a) malleable cast iron couplings, incorporating a rubber seal
and washer
(b) tapped OR non tapped plugs incorporating a rubber seal
Op. 23.05.1996 Dec. 06.09.1996 - TC 9607790
7307.21.00 FLANGES, STAINLESS STEEL PIPE, including internal alumina
ceramic tiles
Op. 28.02.2011 Dec. 23.05.2011 - TC 1107490
7307.21.00 FLANGES, PIPE, stainless steel, seamless
Op. 29.07.1999 Dec. 15.10.1999 - TC 9905666
7307.22.00 FITTINGS, TUBE, stainless steel, with OR without seals, being
threaded bends
Op. 31.03.2010 Dec. 09.07.2010 - TC 1015482
7307.22.00 FITTINGS, VACUUM, stainless steel, operating pressure lower than
133 x 0.0000001 MPa, being EITHER of the following:
(a) couplings;
(b) elbows
Op. 18.12.1997 Dec. 27.02.1998 - TC 9711204
7307.23 BENDS, CROSSES, ELBOWS OR TEES, buttweld, stainless steel,
conforming dimensionally to ANY of the following Specifications:
(a) BS 1640;
(b) ANSI B16.9;
(c) ANSI B16.28
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341312
7307.23 FITTINGS, stainless steel, tube or pipe, buttweld, annealed,
internally polished
Op. 23.11.1987 Dec. 23.02.1989 - TC 8735514
7307.23 FITTINGS, seamless, stainless steel grade 316L, to specification
ASTM 269 or ASTM 270, electropolished internally through entire
length
Op. 20.05.1988 Dec. 02.05.1989 - TC 8805455
7307.23.00 FITTINGS, TUBE OR PIPE, stainless steel in accordance with
EN10253-3 OR EN10253-4, being ANY of the following:
(a) elbows;
(b) tees;
(c) reducers;
(d) collars;
(e) end caps
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 26.10.2015 Dec. 18.01.2016 - TC 1539885
7307.23.00 FITTINGS, TEE, seamless, stainless steel, duplex
Op. 03.09.2015 Dec. 30.11.2015 - TC 1534129
7307.23.00 CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without
seals
Op. 17.06.2014 Dec. 10.09.2014 - TC 1420343
7307.23.00 REDUCERS, seamless, butt weld, stainless steel
Op. 26.10.2012 Dec. 07.01.2013 - TC 1241137
7307.29 RINGS, gasket or packing, to API Specification 6A, capable of
operating at temperatures of 125 degrees C or greater
Op. 30.12.1987 Dec. 27.04.1988 - TC 8733301
7307.29.00 TUBE FITTINGS, stainless steel, press tool connection, having
ALL of the following:
(a) ethylene propylene diene monomer (EPDM) rubber seals;
(b) inside diameter NOT less than 15 mm and NOT greater than
108 mm;
(c) with OR without one flanged OR screw OR plain end
connection;
(d) being ANY of the following:
(i) couplings;
(ii) slip couplings;
(iii) reducers;
(iv) tees;
(v) union connectors;
(vi) adapters;
(vii) end caps
Op. 03.03.2015 Dec. 25.05.2015 - TC 1508749
7307.29.00 TUBE FITTINGS, stainless steel, press tool connection, having
ALL of the following:
(a) ethylene propylene diene monomer (EPDM) rubber seals;
(b) inside diameter NOT less than 15 mm and NOT greater than
108 mm;
(c) with OR without one flanged OR screw OR plain end
connection;
(d) being ANY of the following:
(i) elbows, including back plated;
(ii) bends;
(iii) sleeves
Op. 03.03.2015 Dec. 25.05.2015 - TC 1508754
7307.29.00 PUP JOINTS, OIL AND/OR GAS WELL TUBING, stainless steel,
threaded, perforated, with OR without thread protectors
Op. 06.03.2015 Dec. 25.05.2015 - TC 1509480
7307.29.00 CROSSOVER CONNECTORS, OIL AND/OR GAS WELL, subsea AND/OR
surface, stainless steel
Op. 10.03.2015 Dec. 07.06.2015 - TC 1509604
7307.29.00 PUP JOINTS, TUBING, OIL AND/OR GAS WELL, stainless steel,
threaded, seamless, with OR without thread protectors, having an
external working pressure rating of NOT less than 415 bar and
NOT greater than 450 bar
Op. 24.12.2014 Dec. 14.03.2015 - TC 1500003
7307.29.00 COUPLINGS, FLOW, OIL AND/OR GAS WELL, stainless steel, having
BOTH of the following:
(a) threaded connections;
(b) internal working pressure rating NOT less than 850 bar
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 23.09.2014 Dec. 15.12.2014 - TC 1433855
7307.29.00 CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without
seals
Op. 17.06.2014 Dec. 01.09.2014 - TC 1420587
7307.29.00 STAB PLATES, SUBSEA, stainless steel, having NOT less than 8
connection points
Op. 25.02.2013 Dec. 02.05.2013 - TC 1306853
7307.29.00 COUPLINGS, PIPE, compression, stainless steel, having ALL of the
following:
(a) inside diameter NOT less than 200 mm;
(b) single sealing sleeve consisting of a single sealing lip
on each side with progressive sealing effect;
(c) single radial positioned locking system with 1 OR 2 OR 3
screws
Op. 26.07.2012 Dec. 22.10.2012 - TC 1227050
7307.29.00 CONNECTORS, STAB, SUBSEA, male AND/OR female, with OR without
protective caps
Op. 15.05.2012 Dec. 06.08.2012 - TC 1215919
7307.29.00 FITTINGS, DRAINAGE, Grade 316L stainless steel, being ANY of the
following:
(a) filter baskets;
(b) removable water traps;
(c) grates;
(d) drainage bowls, having a diameter NOT greater than 300 mm
Op. 24.09.2010 Dec. 20.12.2010 - TC 1043685
7307.29.00 FITTINGS, TUBE, stainless steel, with OR without seals, being
ANY of the following:
(a) couplings having a diameter NOT greater than 200 mm;
(b) reducers;
(c) bends;
(d) T junctions;
(e) union connectors;
(f) adapters
Op. 29.04.2010 Dec. 09.07.2010 - TC 1019464
7307.29.00 FITTINGS, PIPE AND TUBE, Grade 316L stainless steel, push fit,
with or without seal, being ANY of the following:
(a) pipe incorporating a socket;
(b) bends;
(c) pipe, having NOT less than 45 degree junctions and NOT
greater than 90 degree junctions;
(d) double sockets;
(e) "P" traps;
(f) bottle trap;
(g) eccentric increasers;
(h) eccentric reducers;
(i) access bends;
(j) threaded adaptor
Op. 25.02.2010 Dec. 14.05.2010 - TC 1009883
7307.29.00 FITTINGS, DRAINAGE, Grade 316L stainless steel, being ALL
of the following:
(a) filter baskets;
(b) removable water traps;
(c) grates
Op. 25.02.2010 Dec. 14.05.2010 - TC 1009880
7307.29.00 FITTINGS, PIPE AND TUBE, stainless steel, being ANY of the
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
following:
(a) sealing rings;
(b) bodies;
(c) cap nuts;
(d) weld cones;
(e) flare adaptors
Op. 11.03.2009 Dec. 06.11.2009 - TC 0941426
7307.29.00 FITTINGS, CAMLOCK, being ANY of the following:
(a) male sections and/or female sections;
(b) plugs;
(c) caps
Op. 20.12.2007 Dec. 07.03.2008 - TC 0710840
7307.29.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the
following;
(a) male sections;
(b) female sections;
(c) lever rings;
(d) male plugs;
(e) female caps
Op. 21.12.2007 Dec. 07.03.2008 - TC 0721937
7307.29.00 COUPLINGS, HOSE, quick connect, comprising ALL of the following:
(a) male sections;
(b) female sections;
(c) lever rings
Op. 21.12.2007 Dec. 14.03.2008 - TC 0721940
7307.29.00 FITTINGS, ROOF DRAINAGE, stainless steel, being ANY of the
following:
(a) rainwater outlets;
(b) hoppers;
(c) elbows;
(d) s-curves;
(e) pipe flaps
including sets of 2 or more of the above
Op. 14.10.2008 Dec. 14.01.2009 - TC 0835301
7307.29.00 COUPLINGS, camlocking, to material 316 stainless steel, 15 mm to 200
mm, inclusive of both adaptors (male) and couplers (female).
Op. 13.08.1993 Dec. 10.02.1994 - TC 9307389
7307.29.00 JOINTS, swivel, stainless steel, v-ring type, pressure rating
greater than 6 800 KPa
Op. 14.06.1993 Dec. 23.09.1993 - TC 9314494
7307.29.00 FITTINGS, pipe, forged stainless steel to specification type F 51
ASTM UNS S 31803, having the surface descaled by turning
Op. 27.05.1994 Dec. 02.09.1994 - TC 9404892
7307.29.00 FITTINGS, vacuum, stainless steel, helium leak tested, rated to
lower than 133 x 10 -7 MPa, being ANY of the following:
(a) plug;
(b) cap;
(c) gland;
(d) body;
(e) female nut;
(f) male nut;
(g) bodies, assembled with nuts and ferrules;
(h) assemblies including ANY of the above
Op. 22.05.1997 Dec. 15.08.1997 - TC 9704622
7307.29.00 COUPLINGS, FLOW, OIL AND GAS WELL, stainless steel
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 15.12.1997 Dec. 27.02.1998 - TC 9711103
7307.91.00 FLANGES, STEEL PIPE, including internal alumina ceramic tiles
Op. 28.02.2011 Dec. 30.05.2011 - TC 1107491
7307.91.00 FLANGES, PIPE, being ANY of the following:
(a) weld neck flanges;
(b) blind flanges;
(c) spectacle blind flanges;
(d) slip on flanges;
(e) socket weld flanges;
(f) threaded flanges;
(g) bulkhead flanges
Op. 20.02.2008 Dec. 02.05.2008 - TC 0803404
7307.91.00 FLANGE ADAPTERS, PIPE OR TUBE OR HOSE, carbon steel, with or
without seal
Op. 03.12.2008 Dec. 27.02.2009 - TC 0842547
7307.91.00 FLANGES, HOT FORGED, SEAMLESS, comprising ALL of the following:
(a) inner diameter NOT less than 1 500 mm;
(b) width NOT greater than 400 mm;
(c) outer diameter NOT less than 2 000 mm
Op. 09.10.2003 Dec. 03.03.2004 - TC 0312809
7307.92.00 FITTINGS, TUBE, carbon steel, press fit, with OR without seals,
being threaded bends having an internal AND/OR external zinc
coating NOT greater than 8 micron
Op. 18.10.2010 Dec. 13.01.2011 - TC 1046727
7307.92.00 ELBOWS, threaded
Op. 08.10.2008 Dec. 14.01.2009 - TC 0834585
7307.92.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with
or without seal, being ANY of the following:
(a) elbows, 90 degrees;
(b) elbows, 45 degrees;
(c) elbows, 3 way tees, being either male to female OR
combinations of both;
(d) tube sleeves;
(e) bends, 90 degrees;
(f) bends, 45 degrees
Op. 03.12.2008 Dec. 27.02.2009 - TC 0842548
7307.92.00 FITTINGS, pipe, steel, complying with standards BS1740 or AS3672
Op. 10.05.1994 Dec. 19.08.1994 - TC 9404635
7307.92.00 FITTINGS, PIPE AND TUBE, including sealing rings, bodies, nuts and
weld cones, having BOTH of the following:
(a) compliance with pressure rating of either LL, L or S to
DIN 2353;
(b) interchangeability of the whole or any component of the
fitting with other fittings or components which comply with
the dimensional specifications set out in DIN 2353,
but NOT including ANY of the following:
(a) stainless steel fittings;
(b) twin ferrule fittings
Op. 03.11.1995 Dec. 09.02.1996 - TC 9511750
7307.92.00 FITTINGS, TUBE, elbow, carbon steel, twin ferrule
Op. 18.11.1997 Dec. 23.01.1998 - TC 9710155
7307.93 FITTINGS, buttweld, in accordance with Dimensional Specification
MSS-SP75 and Material Specification API 5LX
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341295
7307.93 FITTINGS, buttweld pipe, being ANY of the following:
(a) to ASTM Specification A420 GRWPL6:
(i) elbows, 45 degrees;
(ii) elbows, 90 degrees, OD NOT exceeding 304.8 mm;
(iii) reducers, eccentric;
(b) to ASTM Specification A234 GRWP1:
(i) elbows, 45 degrees or 90 degrees, OD NOT exceeding
254 mm;
(ii) reducers, eccentric, OD at larger end NOT exceeding
254 mm
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341297
7307.93 FITTINGS, being ANY of the following:
(a) elbows to ASTM Specification A234 WPB, having a dia less
than 406.4 mm OD;
(b) reducers to ASTM Specification A234 WPB, having BOTH
diameters less than 406.4 mm OD;
(c) elbows, reducers or tees to ASTM Specification A234 WP 11
Op. 19.10.1987 Dec. 21.12.1987 - TC 8735075
7307.93 JOINTS, insulating, monobloc or monolithic
Op. 01.01.1988 Dec. 01.01.1988 - TC 8803112
7307.93.00 CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals
Op. 17.06.2014 Dec. 10.09.2014 - TC 1420583
7307.93.00 FITTINGS, PIPE AND/OR TUBE, butt weld, being caps of carbon
steel to American Society of Testing and Materials Specification
A234 Grade WPB (ASTM A234 Grade WPB)
Op. 21.10.2010 Dec. 10.01.2011 - TC 1047333
7307.93.00 PARTS, BOILER INSPECTION BUTTWELD FITTINGS, being EITHER of the
following:
(a) butt weld hubs;
(b) blind hubs
Op. 03.02.2010 Dec. 23.04.2010 - TC 1005997
7307.93.00 FITTINGS, BUTTWELD, STEEL PIPE OR TUBE, having ALL of the
following:
(a) inspection cap;
(b) clamp assembly consisting of BOTH of the following:
(i) clamp segments;
(ii) studs and nuts,
(c) seal ring;
(d) butt welding hub
Op. 15.12.2009 Dec. 05.03.2010 - TC 0948886
7307.93.00 FITTINGS, PIPE OR TUBE, butt-welded, forged steel, being
reinforced and contoured connections
Op. 28.07.2009 Dec. 16.10.2009 - TC 0927139
7307.93.00 FITTINGS, PIPE AND/OR TUBE, butt weld, alloy steel, being end
caps
Op. 28.07.2009 Dec. 09.10.2009 - TC 0927136
7307.93.00 FITTINGS, BUTTWELD, being ANY of the following:
(a) bends;
(b) crosses;
(c) elbows;
(d) reducers;
(e) tees
Op. 06.06.2005 Dec. 24.10.2005 - TC 0506772
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7307.93.00 FITTINGS, buttweld, forged, integrally reinforced, contoured-insert
vessel or piping branch connections, bore sizes 15 mm - 1 200 mm
Op. 01.03.1993 Dec. 04.06.1993 - TC 9308562
7307.93.00 REDUCERS, buttweld, having a minimum outside diameter between 70 mm
and 200 mm (+ or - 0.001%)
Op. 11.02.1998 Dec. 11.05.1998 - TC 9801278
7307.93.00 FITTINGS, buttweld, to specifications BS1640 OR ANSI B16.9 OR
ANSI B16.28, being ANY of the following:
(a) bends, 30 degrees, 45 degrees, 50 degrees, 60 degrees,
90 degrees OR 180 degrees, having an outside diameter between
17 mm and 406.4 mm;
(b) tees, equal OR reducing, having an outside diameter of
406.4 mm OR less
For the purposes of this order, ALL measurements have a tolerance of
+ OR - 5%
Op. 11.02.1998 Dec. 12.08.1998 - TC 9806998
7307.99 ELBOWS, socketweld, being ANY of the following:
(a) 15 degrees;
(b) 45 degrees;
(c) 90 degrees ID exceeding 50.8 mm
Op. 06.03.1984 Dec. 06.03.1984 - TC 8341420
7307.99 JOINTS, insulating, monobloc or monolithic
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341449
7307.99 PLUGS, pipe, incorporating an oil resistant synthetic rubber seal
capable of sealing pipes having an ID of 49 mm or greater but NOT
exceeding 356 mm at pressures of 48 MPa or less
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341450
7307.99 COUPLINGS, hose, having a working capacity of 206 MPa or greater
Op. 30.10.1984 Dec. 30.10.1984 - TC 8434699
7307.99 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising
male and female ring lock couplings, hinged ring band snap lock
and double lip gasket, to suit pipes and hoses having an OD of
50 mm or greater
Op. 14.12.1984 Dec. 30.04.1985 - TC 8530126
7307.99 UNIONS, hammer, being four lug wing nut type with replaceable
rubber seal, having ANY of the following nominal connecting pipe
sizes on slipfit female pipe end and in Schedule 80 buttweld, male
component weld end:
Nominal connecting Nominal size
pipe size (female end) pipe (weld end)
Outside Dia Outside Dia
(a) 114.3 mm 152.4 mm;
(b) 168.28 mm 203.2 mm;
(c) 219.08 mm 254.0 mm;
(d) 273.05 mm 304.8 mm;
(e) 323.85 mm 355.6 mm;
(f) 355.6 mm 406.4 mm;
(g) 406.4 mm 457.2 mm
Op. 21.04.1987 Dec. 27.08.1987 - TC 8733860
7307.99 RINGS, gasket or packing, to API Specification 6A, capable of
operating at temperatures of 125 degrees C or greater
Op. 01.01.1988 Dec. 27.04.1988 - TC 8802330
7307.99 FITTINGS, pipe, fluoro-polymer lined
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 12.02.1988 Dec. 21.12.1988 - TC 8802801
7307.99 FITTINGS, steel pipe, being EITHER of the following:
(a) three lug wing nut unions, dia NOT exceeding 300 mm,
minimum operating pressure 6.80 MPa;
(b) hub clamp assemblies, consisting of ALL of the following:
(i) clamp segments;
(ii) hubs;
(iii) seal ring
Op. 23.02.1988 Dec. 16.09.1988 - TC 8802877
7307.99 COUPLINGS, casing or tubing, seamless to Specification API-5CT,
section 8
Op. 05.12.1988 Dec. 07.06.1989 - TC 8902264
7307.99 JOINTS, swivel, pressure rating over 40 MPa
Op. 23.04.1991 Dec. 02.09.1991 - TC 9104099
7307.99 CLAMPS, pipe repair (but NOT including clamps incorporating
stainless steel flexible bands), having ALL of the following
characteristics:
(a) seal by ANY of the following methods:
(i) clamping or thrust screws;
(ii) girder rings;
(iii) packing or force screws;
(b) carbon steel construction;
(c) of fixed dia;
(d) capable of withstanding a working pressure of 6 900 kPa
or greater
Op. 01.01.1988 Dec. 11.09.1992 - TC 9206167
7307.99 CLOSURES, pressurised pipeline, hinged, quick release, diameter
150 mm or greater, but NOT including screw top type closures
Op. 13.07.1992 Dec. 08.10.1992 - TC 9206615
7307.99.00 FLOWLINE END TERMINATIONS, SUBSEA, with OR without ANY of the
following:
(a) anodes;
(b) mud mats;
(c) protective frames;
(d) support bases
Op. 15.10.2015 Dec. 05.01.2016 - TC 1538598
7307.99.00 PIPE FITTINGS, being 45 AND/OR 90 degree threaded AND/OR
butt weld carbon steel hammer lug union end connection elbows,
having a design pressure rating NOT less than 2 300 psi
Op. 16.09.2015 Dec. 14.12.2015 - TC 1535358
7307.99.00 HAMMER UNIONS, lugged wing nut type, with OR without seals,
including ANY of the following:
(a) male AND/OR female sub sections;
(b) plugs;
(c) caps;
(d) wing nuts AND/OR split nuts
Op. 16.06.2015 Dec. 08.09.2015 - TC 1521815
7307.99.00 CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals
Op. 17.06.2014 Dec. 10.09.2014 - TC 1420344
7307.99.00 END CAPS, PRESSURE VESSEL
Op. 01.08.2013 Dec. 21.10.2013 - TC 1325951
7307.99.00 CONNECTORS OR COUPLINGS, CASING OR TUBING, OIL AND/OR GAS WELL,
conforming to American Petroleum Institute Specification 5CT
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(API 5CT)
Op. 15.04.2013 Dec. 15.07.2013 - TC 1312752
7307.99.00 CROSSOVER CONNECTORS, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA
AND/OR SURFACE
Op. 25.01.2013 Dec. 08.04.2013 - TC 1303345
7307.99.00 COUPLINGS, CROSSOVER, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA
AND/OR SURFACE
Op. 15.01.2013 Dec. 03.04.2013 - TC 1301796
7307.99.00 COUPLINGS, PIPE, compression, hot dipped galvanised, having ALL
of the following:
(a) inside diameter NOT less than 30 mm;
(b) single sealing sleeve consisting of a single sealing lip
on each side with progressive sealing effect;
(c) single radial positioned locking system with 1 OR 2 OR
3 screws
Op. 26.07.2012 Dec. 22.10.2012 - TC 1227051
7307.99.00 FITTINGS, TUBE, carbon steel, with OR without seals, having an
internal AND/OR external zinc coating NOT greater than 8 micron,
being ANY of the following:
(a) couplings having a diameter NOT greater than 200 mm;
(b) reducers;
(c) bends;
(d) T junctions;
(e) union connectors;
(f) adaptors
Op. 18.10.2010 Dec. 13.01.2011 - TC 1046729
7307.99.00 FITTINGS, MULTILAYERED WELDED STEEL PIPE, being ANY of the
following:
(a) elbows;
(b) joints;
(c) reducers;
(d) T fittings;
(e) bends;
(f) end caps
Op. 07.06.2010 Dec. 30.08.2010 - TC 1025390
7307.99.00 TERMINATION HEADS, subsea
Op. 05.01.2009 Dec. 27.03.2009 - TC 0946016
7307.99.00 OILWELL CONNECTORS, having ALL of the following:
(a) nonhelical interlocking teeth;
(b) metal to metal seals;
(c) diameter NOT less than 50.8 cm
Op. 29.07.2005 Dec. 07.10.2005 - TC 0509995
7307.99.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the
following:
(a) male sections;
(b) female sections;
(c) lever rings;
(d) male plugs;
(e) female caps
Op. 21.12.2007 Dec. 07.03.2008 - TC 0721938
7307.99.00 COUPLINGS, HOSE, QUICK CONNECT, comprising ALL of the following;
(a) male sections;
(b) female sections;
(c) lever ring
Op. 21.12.2007 Dec. 07.03.2008 - TC 0721939
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7307.99.00 FITTINGS, PIPE, being EITHER of the following:
(a) hot tap;
(b) line stop
Op. 21.04.2008 Dec. 11.07.2008 - TC 0804852
7307.99.00 CONNECTORS, HYDRAULIC HOSE, steel
Op. 13.08.2008 Dec. 31.10.2008 - TC 0826255
7307.99.00 FITTINGS, PIPE, forged, integrally reinforced, contoured-insert
vessel or piping branch connections, having a bore size NOT less
than 15 mm and NOT greater than 1 200 mm
Op. 04.09.2008 Dec. 28.11.2008 - TC 0829428
7307.99.00 FITTINGS, ROOF DRAINAGE, galvanized steel, being ANY of the
following:
(a) rainwater outlets;
(b) inclined outlets;
(c) hoppers;
(d) elbows;
(e) s-curves;
(f) hinged outlets;
(g) pipe flaps
including sets of 2 or more of the above
Op. 14.10.2008 Dec. 14.01.2009 - TC 0835300
7307.99.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with
or without seal, being ANY of the following:
(a) reducing or enlarging bush, hexagon;
(b) caps, solid or swivel;
(c) crosses;
(d) nipples, being ANY of the following:
(i) hexagon;
(ii) barrel;
(iii) plain;
(iv) reducing;
(e) sockets, including reducing and enlarging;
(f) plugs, square head or hex head or internal or external
hexagon;
(g) unions;
(h) tube welds or weld-on's;
(i) tube compression and tube flared fittings
Op. 03.12.2008 Dec. 27.02.2009 - TC 0842546
7307.99.00 FITTINGS, pipe and tube, metric, including sealing rings, bodies and
nuts, to specifications DIN 2353 or DIN 3859 in ANY of the
following sizes:
(a) 4 mm;
(b) 6 mm;
(c) 8 mm;
(d) 10 mm;
(e) 12 mm;
(f) 14 mm;
(g) 15 mm;
(h) 16 mm;
(i) 18 mm;
(j) 20 mm;
(k) 22 mm;
(l) 25 mm;
(m) 28 mm;
(n) 30 mm;
(o) 35 mm;
(p) 38 mm;
(q) 42 mm;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(r) 50 mm
Op. 02.12.1993 Dec. 11.04.1994 - TC 9400309
7307.99.00 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising
male and female ring lock couplings, hinged ring band snap lock,
to suit pipes and hoses having an OD of 50 mm or greater
Op. 24.02.1994 Dec. 03.06.1994 - TC 9402433
7307.99.00 FITTINGS, pipe, high pressure, steel, complying with ALL the
following standards:
(a) ASTM A105;
(b) ANSI B16.11;
(c) BS3799
Op. 27.04.1994 Dec. 29.07.1994 - TC 9404403
7307.99.00 BRANCH CONNECTIONS, weld on type, complying with ALL the following
standards:
(a) ASTM A105;
(b) ANSI B31-1 1980;
(c) ANSI B16-9;
(d) BS3351 1971
Op. 27.04.1994 Dec. 05.08.1994 - TC 9404404
7307.99.00 FITTINGS, pipe and tube, including sealing rings, bodies, nuts and
weld cones, having BOTH of the following:
(a) compliance with pressure rating being either LL, L or S to
DIN 2353;
(b) interchangeability of the whole or any component of the
fitting with other fittings or components which comply with
the dimensional specifications set out in DIN 2353,
but NOT including ANY of the following:
(a) stainless steel fittings;
(b) twin ferrule fittings
Op. 25.11.1994 Dec. 14.03.1995 - TC 9409468
7307.99.00 FITTINGS, STEEL, being EITHER of the following:
(a) hose couplings having a female ACME coupling connection within
the range of 44.45 mm to 82.55 mm (both inclusive);
(b) adapters with male ACME connection within the range of
44.45 mm to 82.55 mm (both inclusive)
Op. 14.02.1995 Dec. 20.10.1995 - TC 9501971
7307.99.00 FITTINGS, PIPE, unthreaded, being ANY of the following:
(a) joining rings having a diameter of 80 mm or greater but NOT
exceeding 800 mm;
(b) pressed bends of galvanised or mild steel in angles from 7.5
degrees or greater but NOT exceeding 90 degrees and diameter
of 80 mm or greater but NOT exceeding 400 mm;
(c) straight ducting with fully rolled beaded edge having a
diameter of 155 mm or greater but NOT exceeding 160 mm;
but NOT including fittings of stainless steel
Op. 31.08.1995 Dec. 08.12.1995 - TC 9510236
7307.99.00 CLOSURES, PRESSURISED PIPELINE, having ALL of the following:
(a) a cap;
(b) a welding hub, with an integrated semi-dovetailed O-Ring
groove in the face;
(c) capable of horizontal, vertical or angle installations
Op. 22.03.1996 Dec. 28.06.1996 - TC 9604891
7307.99.00 FITTINGS, TUBE, carbon steel, twin ferrule
Op. 17.11.1997 Dec. 23.01.1998 - TC 9710154
7307.99.00 FITTINGS, ON-LINE HYDRAULIC LINE TESTING, being couplers, adaptors
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
OR stand pipes, working pressures up to 40 MPa in hose sizes 2 mm
and 4 mm
Op. 10.12.1997 Dec. 27.02.1998 - TC 9710916
7307.99.00 GROUND CONES, FLEXIBLE METAL CONDUIT FITTING
Op. 26.02.1998 Dec. 11.05.1998 - TC 9801691
7307.99.00 NIPPLES, LANDING, SUB SURFACE FLOW CONTROL
Op. 01.05.1998 Dec. 17.07.1998 - TC 9803639
7307.99.00 COUPLINGS, SUCKER ROD, 12.7 mm to 28.6 mm (1/2" to 1 1/8")
Op. 05.11.1998 Dec. 15.01.1999 - TC 9809843
7308.10.00 PARTS, MODULAR PANEL BRIDGING, conforming to BS:EN 10025 and
BS:EN 10113, being ANY of the following:
(a) panels;
(b) chord reinforcement;
(c) rakers;
(d) frames;
(e) transoms;
(f) sway brace;
(g) braces;
(h) decks;
(i) kerbs;
(j) in fills;
(k) post ends;
(l) beams;
(m) screw deck clamps;
(n) signs;
(o) plates;
(p) plugs;
(q) links;
(r) extensions;
(s) markers;
(t) diaphragms;
(u) packers;
(v) spikes;
(w) seal kits;
(x) keys;
(y) bars;
(z) tin snips;
(aa) gimlets;
(ab) grillages;
(ac) posts;
(ad) base plates;
(ae) toe ramps;
(af) ground beams;
(ag) lugs;
(ah) holdfast pickets and spikes;
(ai) D shackles;
(aj) slings;
(ak) tirfor;
(al) channels;
(am) angles;
(an) walkways;
(ao) stanchions;
(ap) handrails;
(aq) staircases;
(ar) blocks;
(as) sway frames;
(at) rollers;
(au) links;
(av) stool outers;
(aw) struts;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(ax) ties;
(ay) gauges
Op. 05.12.2003 Dec. 31.03.2004 - TC 0315337
7308.30.00 SLIDING DOOR SYSTEM, CAVITY, BRICK WALL, incorporating
overlapping steel mesh
Op. 10.06.2009 Dec. 04.09.2009 - TC 0919622
7308.30.00 GRILLS, SECURITY, metal, retractable, self locking
Op. 31.05.2006 Dec. 11.08.2006 - TC 0609406
7308.40.00 STEEL COMPONENTS, being temporary shuttering AND part of a
removable modular system, including prefabricated grids AND
panels, being soffit bases
Op. 17.02.2014 Dec. 02.07.2014 - TC 1406250
7308.40.00 COMPONENTS, SCAFFOLDING, being ANY of the following:
(a) chainwire rolls;
(b) ledgers;
(c) tie bars;
(d) toe board clips;
(e) wall ties;
(f) wall tie tubes
Op. 13.12.2013 Dec. 10.02.2014 - TC 1405222
7308.40.00 COMPONENTS, SCAFFOLDING, complying with Australian Standard AS
1576.2, being ANY of the following:
(a) double couplers;
(b) double reducers;
(c) swivel couplers;
(d) swivel reducers;
(e) putlog half;
(f) putlog hooks;
(g) putlog full;
(h) putlog blades;
(i) internal joiners;
(j) gravlock beam clamps;
(k) swivel beam clamps
Op. 13.12.2013 Dec. 10.02.2014 - TC 1405226
7308.40.00 SCAFFOLDING COMPONENTS, being ANY of the following:
(a) V-housings;
(b) camlocks;
(c) ledgers;
(d) toe board clamps
Op. 13.12.2013 Dec. 10.02.2014 - TC 1405223
7308.40.00 PROPS, HOT DIPPED GALVANISED AND/OR ZINC PLATED, having a rolled
thread on the outer tube
Op. 13.11.2007 Dec. 29.01.2008 - TC 0719361
7308.90 RAILS, elevator guide, weight less than 6 kg/m or exceeding
26 kg/m
Op. 28.02.1984 Dec. 28.02.1984 - TC 8437468
7308.90 CRASH CUSHIONS, roadside hazard, energy absorbing, meeting NCHRP
230 Test tolerances
Op. 18.11.1988 Dec. 19.10.1990 - TC 8810530
7308.90.00 PARTS, FORMWORK AND/OR SAFETY SCREEN, VERTICAL CLIMBING SYSTEM,
being ANY of the following:
(a) beams;
(b) braces;
(c) brackets;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(d) frames;
(e) latches;
(f) masts;
(g) supports;
(h) bracing tubes;
(i) struts;
(j) adapters;
(k) connectors;
(l) extensions
Op. 01.09.2015 Dec. 08.02.2016 - TC 1533598
7308.90.00 CLIPS, ROOF AND/OR WALL SHEETING
Op. 13.03.2015 Dec. 25.05.2015 - TC 1510243
7308.90.00 BEAMS, FLOORING SUPPORT, steel, assembled OR unassembled, having
ALL of the following:
(a) beam lengths NOT less than 8 200 mm;
(b) complete penetration butt welded steel plate complying with
Australian Standard AS 4100-1998, 9.7.2.7;
(c) bevelled beam ends, with end plates attached,
with OR without ANY of the following:
(i) nuts;
(ii) bolts;
(iii) washers
Op. 10.11.2014 Dec. 15.04.2015 - TC 1439131
7308.90.00 PUSH BACK PALLET RACKING SYSTEM, including BOTH of the following:
(a) trolleys;
(b) support beams
Op. 03.12.2014 Dec. 02.03.2015 - TC 1442731
7308.90.00 PARTS, DEMOUNTABLE FLOOD CONTROL CONTAINMENT SYSTEM, conforming
to British Standard PAS 1188-4, (BSI PAS 1188-4), being ANY of
the following:
(a) supports;
(b) corner posts;
(c) braces;
(d) support covers
Op. 06.11.2014 Dec. 28.01.2015 - TC 1438761
7308.90.00 PARTS, FLARE GAS STACK, LNG CONDITIONING, being ANY of the
following:
(a) stack tube segments with OR without internal low pressure
riser sections;
(b) external high pressure riser sections with OR without riser
guide supports;
(c) riser bracing supports;
(d) platforms;
(e) ladders;
(f) handrails
Op. 04.09.2014 Dec. 16.01.2015 - TC 1431532
7308.90.00 ACCESS BOXES OR CUBES OR PRISMS, rectangle, steel, modular,
including ANY of the following:
(a) connector plates;
(b) end panels;
(c) brackets;
(d) cross beams;
(e) spreader;
(f) steel plate supports
Op. 05.09.2014 Dec. 01.12.2014 - TC 1431647
7308.90.00 GUIDE RAILS, iron AND/OR steel, cold-drawn, having a rail length
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
less than 5.5 m, with OR without fishplates
Op. 17.04.2014 Dec. 14.07.2014 - TC 1413672
7308.90.00 SUPPORT STRUCTURES, COMPRESSOR TRAIN, TECHNICAL AMMONIUM NITRATE
PLANT
Op. 24.03.2014 Dec. 25.06.2014 - TC 1410306
7308.90.00 SHORING, steel, modular, hydraulic adjustable, including ALL of
the following:
(a) braces;
(b) struts;
(c) beams
Op. 15.10.2013 Dec. 03.03.2014 - TC 1334324
7308.90.00 FARROWING CRATES, PIGGERY, unassembled, having ALL of the
following:
(a) compressed fibre panelling;
(b) steel crates;
(c) steel fencing;
(d) plastic covers
Op. 20.08.2013 Dec. 18.11.2013 - TC 1328433
7308.90.00 PARTS, STRUCTURAL STEEL SECTIONS, WHARF, being EITHER of the
following:
(a) topside modules NOT less than 75 tonnes;
(b) dolphins NOT less than 25 tonnes
Op. 17.10.2013 Dec. 17.10.2013 - TC 1332986
7308.90.00 STRUCTURES, STEEL, MARINE BERTHING, being ANY of the
following:
(a) marine piles NOT less than 750 mm diameter;
(b) dolphins NOT less than 25 tonnes;
(c) topside modules NOT less than 75 tonnes
Op. 17.10.2013 Dec. 17.10.2013 - TC 1332984
7308.90.00 TEMPLATES, ANCHOR BOLT, TECHNICAL AMMONIUM NITRATE (TAN)
PLANT
Op. 30.05.2013 Dec. 26.08.2013 - TC 1317818
7308.90.00 SOLDIERS, FORMWORK, having ALL of the following:
(a) length NOT greater than 3 650 mm;
(b) width NOT less than 220 mm;
(c) hole diameter NOT greater than 105 mm
Op. 19.04.2013 Dec. 05.08.2013 - TC 1313426
7308.90.00 PARTS, STRUCTURAL STEEL, COAL PLANT OR IRON ORE PLANT, being
ANY of the following:
(a) rolled, hollow or welded sections;
(b) beams;
(c) grating,
(d) stairways and/or treads;
(e) plates;
(f) handrails (with or without kick plates);
(g) stanchions;
(h) purlins and girts;
(i) packing and shims;
(j) guards;
(k) legs;
(l) stringer and ground modules;
(m) frames;
(n) wear liners;
(o) gantries
Op. 30.04.2013 Dec. 11.06.2013 - TC 1319269
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7308.90.00 STRUCTURES, STEEL, GAS FUELLED POWER PLANT, being EITHER of the
following:
(a) exhaust gas stack;
(b) radiator platform
Op. 13.03.2013 Dec. 18.06.2013 - TC 1309205
7308.90.00 WATER DIVERSION OR DAM BARRIERS, mobile, including ALL Of the
following:
(a) steel A shaped frames;
(b) steel connecting rods;
(c) plywood AND/OR aluminium panels;
(d) plastic membrane sheets;
(e) steel clips AND chains;
(f) storage crates AND wooden pallets
Op. 19.02.2013 Dec. 02.05.2013 - TC 1306230
7308.90.00 ACCESS FLOORING, having BOTH of the following:
(a) steel encapsulated chipboard core panels AND/OR calcium
sulphate core panels;
(b) pedestals, including a head, base and gasket
Op. 23.10.2012 Dec. 14.01.2013 - TC 1240491
7308.90.00 PARTS, ACCESS FLOORING, being ANY of the following:
(a) steel encapsulated chipboard core panels AND/OR calcium
sulphate core panels;
(b) pedestals, including a head, base and gasket;
(c) stringers, complete with gasket
Op. 23.10.2012 Dec. 14.01.2013 - TC 1240492
7308.90.00 STRUCTURES, STEEL, GAS STACK, VENT OR FLARE, including ALL of
the following:
(a) gas stack tubes;
(b) bracing;
(c) beams;
(d) ladders;
(e) handrails
Op. 15.10.2012 Dec. 07.01.2013 - TC 1239299
7308.90.00 PARTS, FOUNDATION, VERTICAL ROLLER MILL, CEMENT GRINDING, being
ANY of the following:
(a) multi-drive foundation frames;
(b) thrust bearing gearbox base plates;
(c) gearbox plate recess boxes;
(d) anchorage base plates;
(e) mill foundation anchor plates;
(f) mill foundation slide rails;
(g) rocker arm support pedestals;
(h) assembly and alignment equipment having ALL of the
following:
(i) I-beams;
(ii) threaded rod;
(iii) compensation plates;
(iv) plates,
(i) anchor bolt recess boxes;
(j) I-beams being foundation embedments
Op. 30.08.2012 Dec. 21.11.2012 - TC 1232381
7308.90.00 MARINE BERTH MODULES, having ALL of the following:
(a) width NOT less than 16 m;
(b) length NOT less than 39 m;
(c) weight NOT less than 400 t
Op. 01.08.2012 Dec. 15.10.2012 - TC 1227730
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
7308.90.00 PARTS, MODULAR MULTIDIRECTIONAL FRAMEWORK, conforming to
European Standard 13480 (EN:13480) and European Standard
1993 (EN:1993), being ANY of the following:
(a) adapters;
(b) bases;
(c) beams;
(d) ends;
(e) joints;
(f) plates;
(g) spider clamps
Op. 26.06.2012 Dec. 12.09.2012 - TC 1222230
7308.90.00 ROOFING, MODULAR, being ANY of the following:
(a) roof cassettes;
(b) ridge cassettes;
(c) roof beams;
(d) roof girders;
(e) ridge supports;
(f) beam stiffeners;
(g) tubular stiffeners;
(h) lattice beam connectors;
(i) wedges;
(j) clamping plates;
(k) roof supports
Op. 29.12.2011 Dec. 26.03.2012 - TC 1142644
7308.90.00 PARTS, MARINE WHARF, being steel pile caps
Op. 16.11.2011 Dec. 30.01.2012 - TC 1138231
7308.90.00 PANELS, INSULATING, consisting of polyurethane inner core with
galvanised steel sheeting BOTH sides, having BOTH of the
following:
(a) steel sheet thickness NOT less than 0.4 mm;
(b) polyurethane thickness NOT less than 20 mm
Op. 27.07.2009 Dec. 09.10.2009 - TC 0926917
7308.90.00 MARINE PILINGS, steel, having ALL of the following:
(a) thickness NOT less than 20 mm;
(b) length NOT less than 28.5 m;
(c) diameter NOT less than 900 mm;
(d) maximum of one splice per piling;
(e) maximum straightness difference of 1 mm per metre over
entire length
Op. 30.04.2009 Dec. 24.07.2009 - TC 0914435
7308.90.00 STRUCTURES, FACADE, woven mesh, stainless steel
Op. 18.04.2007 Dec. 06.07.2007 - TC 0705685
7308.90.00 PARTS, FORMWORK, PANEL WALL SYSTEM, being ANY of the
following:
(a) adapters;
(b) add-on pieces;
(c) adjustment pieces;
(d) angles;
(e) bases;
(f) braces;
(g) brackets;
(h) clamps;
(i) cones;
(j) connector assemblies, comprising both ends and clamps;
(k) connectors;
(l) hinged and/or fixed corners;
(m) cross-bars;
(n) ends;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(o) fasteners;
(p) form strips;
(q) frames;
(r) guardrails;
(s) joints;
(t) locating pins;
(u) mid rails;
(v) panels;
(w) plates;
(x) platform beams;
(y) platforms;
(z) plugs;
(aa) posts;
(ab) props;
(ac) railing;
(ad) spindles;
(ae) spacer and/or centre tubes;
(af) stiffeners;
(ag) stop ends;
(ah) struts;
(ai) tie rods;
(aj) tighteners;
(ak) transport hooks;
(al) triangular wedges;
(am) waler spanners;
(an) walers;
(ao) wedges
Op. 13.11.2007 Dec. 29.01.2008 - TC 0719350
7308.90.00 PARTS, FORMWORK, SOLDIER SYSTEM, being ANY of the following:
(a) adapters;
(b) bases;
(c) braces;
(d) brackets;
(e) clamps;
(f) clips;
(g) connectors;
(h) couplers;
(i) edge angles;
(j) fork arms;
(k) fork heads;
(l) guardrails;
(m) jacks;
(n) lifting loops and/or plates and/or brackets;
(o) pivots;
(p) plates;
(q) plumbing braces;
(r) posts;
(s) shoring adapters;
(t) soldiers, having holes NOT greater than 70 mm
diameters;
(u) spreader connections and/or beams and/or adaptors;
(v) stabilisers;
(w) turnbuckles;
(x) u-heads;
(y) brackets (high load washer);
(z) web stiffeners;
(aa) wheel and bracket assemblies, comprising both wheels and
brackets
Op. 13.11.2007 Dec. 29.01.2008 - TC 0719351
7308.90.00 PARTS, MUSHROOM SUBSTRATE PASTEURIZATION TUNNELS OR BUILDINGS,
being ANY of the following:
(a) connection plates;
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
(b) beams;
(c) pillars;
(d) panels;
(e) profile sheets;
(f) walls;
(g) roofing
Op. 07.11.2008 Dec. 30.01.2009 - TC 0838882
7308.90.00 SHAPES AND PROFILES, of puddled wrought iron
Op. 13.01.1994 Dec. 22.04.1994 - TC 9401293
7308.90.00 CHILD SAFETY GATES OR EXTENSIONS, DOMESTIC, internal
Op. 29.09.2000 Dec. 15.12.2000 - TC 0008230
7308.90.00 GUIDE RAILS, LIFT, hot rolled, bright drawn and planed
Op. 22.02.2001 Dec. 04.05.2001 - TC 0101755
7308.90.00 PARTS, ACCESS FLOORING, being ANY of the following:
(a) steel cementitious floor panels;
(b) pedestals;
(c) stringers;
(d) pedestal heads
Op. 28.07.2004 Dec. 11.10.2004 - TC 0407789
7308.90.00 ACCESS FLOORING, comprising ALL of the following:
(a) steel cementitious floor panels;
(b) pedestals;
(c) stringers;
(d) pedestal heads
Op. 05.08.2004 Dec. 18.10.2004 - TC 0408063
7309.00.00 TANKS, PICKLING, acid OR flux, having BOTH of the following:
(a) composite synthetic ceramic AND glass fibre laminate wall
panels;
(b) steel frames
Op. 15.12.2015 Dec. 07.03.2016 - TC 1545049
7309.00.00 FURNACE DRUMS, METALLICS RECOVERY, having ALL of the
following:
(a) gross capacity NOT greater than 2 550 kg;
(b) bolt-on lids AND seals with spout cover cap;
(c) lid fixing plates
Op. 17.11.2015 Dec. 10.02.2016 - TC 1541859
7309.00.00 SILOS, bolted modules, steel, whether OR
not assembled, with OR without stairs, having ALL of the
following:
(a) piping AND/OR hoses with OR without connectors;
(b) flow control valves;
(c) level measurement microwave sensor including display;
(d) capacity NOT less than 155 cubic metres and NOT greater
than 4 500 cubic metres
Op. 21.04.2015 Dec. 31.08.2015 - TC 1515310
7309.00.00 TANKS, HOT WATER, having ALL of the following:
(a) welded steel plate construction;
(b) insulation AND cladding thickness NOT less than 200 mm;
(c) temperature capacity NOT less than 5 degrees Celsius and
NOT greater than 95 degrees Celsius;
(d) pressure capacity NOT less than 56 mbar;
(e) water capacity NOT less than 100 000 L
Op. 20.12.2013 Dec. 10.04.2014 - TC 1342075
7309.00.00 TANKS, WASTE WATER, glass lined steel, having BOTH of the
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
following:
(a) diameter NOT less than 4 200 mm;
(b) height NOT less than 5 600 mm
Op. 06.11.2013 Dec. 03.02.2014 - TC 1337391
7309.00.00 CONTAINMENT SYSTEM, TANK, WATER AND/OR BRINE, expandable,
portable, including ALL of the following:
(a) tank wall panels;
(b) liner clamp;
(c) wind ring;
(d) maximum capacity NOT greater than 21,005 cubic metres;
(e) maximum diameter NOT greater than 150 metres
Op. 09.04.2013 Dec. 25.09.2013 - TC 1312233
7309.00.00 TANKS, ION EXCHANGE, with OR without platforms AND ladders
Op. 17.06.2011 Dec. 12.09.2011 - TC 1119444
7309.00.00 TANKS, GERMINATING AND KILNING, BARLEY MALT, steel,
prefabricated, having a minimum batch load capacity NOT less
than 360 tonne
Op. 06.08.2007 Dec. 12.10.2007 - TC 0712554
7309.00.00 TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity
exceeding 300 L and NOT greater than 500 L
Op. 07.03.2008 Dec. 16.05.2008 - TC 0803919
7309.00.00 SURGE TANKS, VERTICAL, OIL AND GAS WELL TESTING
Op. 06.08.2008 Dec. 24.10.2008 - TC 0825351
7309.00.00 DUST AND FILLER SILO MODULE, ASPHALT PLANT
Op. 05.09.2008 Dec. 12.12.2008 - TC 0829721
7309.00.00 RECLAIMED ASPHALT PAVEMENT (RAP) MODULE, ASPHALT PLANT
Op. 05.09.2008 Dec. 28.11.2008 - TC 0829756
7309.00.00 COLD FEED MODULE, ASPHALT PLANT
Op. 05.09.2008 Dec. 28.11.2008 - TC 0829971
7310.10.00 TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity NOT
less than 50 L and NOT greater than 300 L
Op. 06.03.2008 Dec. 16.05.2008 - TC 0803685
7310.10.00 KEGS, BEVERAGE, stainless steel, with OR without spears
Op. 26.06.2003 Dec. 15.09.2003 - TC 0307781
7310.29 CONTAINERS, cryogenic, insulated or vacuum wall, using liquefied
gas as a refrigerant medium to store goods (OTHER THAN gas),
at a temperature below - 100 degrees C
Op. 28.02.1984 Dec. 28.02.1984 - TC 8341467
7310.29.00 KEGS, BEVERAGE, stainless steel, having a volume capacity less
than 50 L, with OR without keg spears
Op. 14.05.2014 Dec. 04.08.2014 - TC 1416208
7310.29.00 TINS, PACKAGING, tin coated, with
or without hinged lid
Op. 15.09.2009 Dec. 27.11.2009 - TC 0934614
7310.29.00 TANKS, COLD WATER, diaphragm pressure, having a volume capacity
NOT greater than 50 L
Op. 06.07.2009 Dec. 18.09.2009 - TC 0923307
7310.29.00 TANKS, COLD WATER, diaphragm pressure, having a capacity less
than 50 litres
Tariff Description
===========================================================================
Item 50 applies unless otherwise stated.
Op. 04.06.2009 Dec. 28.08.2009 - TC 0918884
7310.29.00 JERRY CANS, conforming to Australian/New Zealand Standard
2906:2001 (AS/NZS 2906:2001)
Op. 28.01.2009 Dec. 19.06.2009 - TC 0902741
7310.29.00 TINS, NOVELTY, having less than 220 grams of confectionery
and/or bakers wares
Op. 15.09.2005 Dec. 25.11.2005 - TC 0512191