TD2 QuickStart Guide

Solutions for the Digital Evidence Lifecycle™

Device Connection Diagram

Step-by-Step Installation

Forensic Duplicator

Guidance SoftwareW223 N608 Saratoga DriveWaukesha, WI 53186Toll Free: 1 (866) 973-6577Main: 1 (626) 229-9191www.tableau.com

©2012 Guidance Software, Inc. All Rights Reserved. EnCase and Guidance Software are registered trademarks or trademarks owned by Guidance

Software in the United States and other jurisdictions and may not be used without prior written permission. All other marks and brands may be

claimed as the property of their respective owners. Updated 11-2012.

8

Source Destination

4b1

2a

3a

3b

2b

5b

4a

5a

7 6

(2x)

Cable Recommendations

2a. SATA Drive Interface TC3-8 SATA

2b. IDE Drive InterfaceTC6-8 IDE

3a. SATA Drive Power TC5-8-R2 Drive Power

3b. IDE Drive Power TC2-8-R2 Drive Power

4a/4b. SATA Drive Interface

TC4-8-R2 (Unified)

5a/5b. SATA Drive PowerTC4-8-R2 (Unified)

6. USB 2.0 Ports (2x)

7. FireWire 400 PortTC7-6-6 1394A

Note: When imaging 1.8” and 2.5” notebook or 1.8” ZIF IDE drives, please use the properly sized Tableau drive adapter andTC6-2 IDE Signal Cable.

SAS and USB Protocol Modules are now available. Visit www.tableau.com/tdp for more information.

Note: Use cable TC3-9-1M when imaging to the Tableau TMSS Storage Systems.

8. Power (DC In)TP4 Power Supply

1. Membrane Power Switch Confirm TD2 is OFF

2a./2b. Source Drive Interface Connect IDE or SATA source drive to TD2

3a./3b. Source Drive Power Connect IDE or SATA to TD2 source drive power

4a./4b. SATA Destination Drive Interface Connect TD2 to SATA destination drive(s)

5a./5b. SATA Destination Drive Power Connect TD2 to SATA destination drive power

6. USB 2.0 Port Save logs to a USB storage device and/or use duplicator with a USB keyboard (optional)

7. FireWire 400 Port Connect TD2 to external computer for

firmware updates (via Tableau firmware update utility) as necessary

8. Power (DC In) Connect TP4 power supply to TD2 DC In

Powering on the TD2: Power on the TD2, source drive, and destination drive by pressing the TD2 membrane power switch.

Setup Wizard: Upon initial startup, the user will be prompted to configure the TD2. These settings will be saved for future duplications.

One Button Duplication: Follow instructions to connect drives and power-on the TD2. Press the start button to verify destination drive against presets and initiate duplication.

LED Indicators

For the TD2 Users’ Guide and additional product information, visit www.tableau.com/td2.

DC Power InPower available at power source

IDE or SATASource Detect Flashing illumination: Detecting IDE or SATA source driveSteady illumination: IDE or SATA source drive detected

PowerDuplicator turned ON

SATA Destination1&2 Detect Flashing illumination: Detecting IDE or SATA destination driveSteady illumination: IDE or SATA destination drive detected

AlertFlashing illumination: Activity paused, user response requiredSteady illumination: Read/write failure encountered

BusySource or destination drive activity

TD2 Menu Options

Duplicate Disk * Disk-to-Disk Disk-to-File Format (FAT32) Format Destination Format USB Wipe Disk(Destination Only) One-Pass Write Multi-Pass Write

Hash Utilities Source (MD-5 & SHA-1) Blank Check Source Disk Destination 1 Disk Destination 2 DiskDisk Information Source Disk Destination 1 Disk Destination 2 Disk

Disk Utilities Remove DCO & HPA Remove HPALogs View Logs Save All Logs Print All Logs Erase Logs

Setup System Options Imaging Options TD2 Options Factory Reset

* Image verification enabled by default.