1

Transference Of Heat

syllabus

Thermal expansion of solids, liquids and gases; Calorimetry, latent heat; Heat conduction in one dimension; Elementary concepts of convection and radiation; Newtons law of cooling; bulk modulus of gases; Blackbody radiation: absorptive and emissive powers; Kirchhoffs law, Wiens displacement law, Stefans law, Specific heat of a liquid using calorimeter (M and E)

1. Thermal Expansion

When a body is heated, it expands in terms of length, area & volume and temperature rises. In a solid, molecules can only have thermal agitation (random vibrations). As temperature of a body increases, the vibrations of molecules will become fast and due to this the rate of collision among neighbouring molecules increases, it develops a thermal stress in the body and due to this the intermolecular separation increases which results in thermal expansion of body. At ordinary temperatures, the atoms in a solid oscillate about their equilibrium position with amplitude of approximately 1011 m. The average spacing between the atoms is about 1010 m. As the temperature of solid increases, the atoms oscillate with greater amplitudes, as a result the average separation between them increases. Consequently the object expands.

In the similar way the block diagram shown in Fig. explains the way how thermal expansion takes place.

Thermal expansion of a substance can be classified in three broad categories, these are (i) Linear Expansion (ii) Superficial Expansion and (iii) Cubical Expansion or Volume Expansion

(i) Linear Expansion: Consider a rod of length l1 at a temperature T1. Let it be a heated to a temperature T2 and the increased length of the rod be l2 then

l2( l1 (1( ((t)

( ( Coefficient of linear expansion and

Example 1.The density of substance at 0(C is 10 g cm-3 and at 100(C, its density is 9.7g cm-3. The coefficient of linear expansion of substance is

Solution:

(ii) Superficial Expansion (expansion in surface area): If A1 is the area of solid at T1 (C and A2 is the area at T2(C . Then

A2 ( A1(1 ( (t )

Coefficient of superficial (areal) expansion and

(iii) Volume expansion (Part A: expansion in solids): If V1 is the volume of solid at T1(C and V1 is the volume at T2 (C then

coefficient of cubical (volume) expansion and

Note: For isotopic solids:Relation between expansion coefficient are

As temperature increases, density of solid decreases. If d1 is the density at T1(C, d2 is the density at T2(C then

(iv) Expansion of gases (Part B: expansion in gases):Pressure coefficient of a gas is the ratio of increase in pressure for 1(C rise in temperature to the pressure at 0(C, provided the volume of the gas is kept constant.

(p =

Where(p = pressure coefficient

Pt = pressure at t(C

Po= pressure at 0(C

Volume coefficient of a gas is similarly defined as (pressure being kept constant)

(v =

Where(v = volume coefficient

Vt = volume at t(C

Vo= volume at 0(C

Experiments have shown the value of (p (or (v) is the same for all gases and equal to 1/273 per degree celsius, i.e.

(p = (v = per(C or per K,

Where K stands for absolute of kelvin temperature.

Example 2.A grid iron pendulum consists of 5 iron rods and 4 brass rods. What will be the length of each brass rod if the length of each iron rod is 1 m ? ((Fe= 12 ( 10-6/(C, (brass = 20 ( 10-6/(C)

Solution:There are 5 iron rods and 4 brass rods in the pendulum. The number of iron in one half of the pendulum including the central rod is 3. The number of brass rods is 2.

Since the pendulum is compensated,

2. ERROR in measurament DUE TO THERMAL EXPANSION

2.1 HEATING A METALLIC SCALE

A metallic scale (linear) expands in length when heated. As a result all the markings are displaced from their usual (correct) positions.

A reading of l unit on a heated scale is equivalent to an actual length of l , where is coefficient of linear expansion of material of scale, and (t is the temperature of the heated scale.

( If the reading is x, actual length ( x(1 ( ( (t)

actual length ( reading (1 ( ( (t)

2.2 DIFFERENCE OF LENGTHS OF TWO RODS

Consider two rods 1 and 2 of lengths l1 and l2. Let they be heated through a temperature . If l1 and l2 are their expanded lengths, then:

l2 ( l2 where is coefficient of linear expansion of rod 2

l1 ( l1 where is coefficient of linear expansion of rod 1

Since the difference of length of two rods is constant

Example3.Two rods of length l1 and l2 are made of materials whose coefficients of linear expansion are (1 and (2 respectively. If the difference between the two lengths is independent of temperature, then relation between length and linear expansion coefficients.Solution:

2.3 TIME PERIOD OF PENDULUM

Time period (T) of a sample pendulum of length l is given by

If there is a rise in temperature by (t, length of the pendulum increases and hence the time period increase. As a result the clock slows down.

If l0 be the length of the pendulum and corresponding time period be T0 then

If the pendulum be heated by (t (rise in temperature), the new time period T1 is:

(

as ( is very small

(

The above relation gives the time lost per second by the pendulum clock. If (t is the fall in temperature, same equation will give the time gained by the clock per second as its oscillation will become faster due to reduction in its length. Example 4:A clock with a metallic pendulum is 5 second fast each day at a temperature of 15and 10 seconds slow each day at a temperature of 30. Find coefficient of linear expansion for the metal.Solution:

Time lost or gained per second by a pendulum clock is given by

( Here is difference of temperature)

Here temperature is higher then graduation temperature thus clock will loose time and if it is lower then graduation temperature will gain time.

If graduation temperature of clock is T0 then we have.

At 15(C, clock is gaining time, thus

5 =

(1)

At 30(C clock is loosing time, thus

10 =

(2)

Dividing equation (2) by (1), we get

2(T0 15) = (30 T0)

or

T0 = 20(C

Thus from equation (1)

2.4 STRESS IN OBJECTS DUE TO THERMAL EXPANSION

If crosssectional area of wire is A and F be the tension developed in wire due to stretching. Thus the stress developed in the wire due to this tension F is given as

Strees = = F / A

..(1)

Strain produced in wire due to its elastic properties is

Strees =

..(2)

If youngs modulus of the material of wire is Y, we have

or

or

..(3)

Equation - (3) gives the expression for tension in the wire due to decrease in its temperature by (T. This result gives the tension in wire if initially wire is just taught between clamps. If it already has some tension in it then this expression will give the increment in tension in the wire.

Example 5.A uniform metal rod of 2 m m2 cross-section is heated from 0(C to 20(C. The coefficient of liner expansion of the rod is 12 ( 10-6 per (C, Y=1011 N/m2. The energy stored per unit volume of the rod is

solution:Energy per unit volume

3. SPECIFIC HEAT

When heat energy flows into a substance, the temperature of the substance usually rises.

The heat required to raise the temperature of unit mass of a body through 1 oC or ( 1 oK ) is called specific heat capacity or simply specific heat of the material of the body. If (Q heat changes the temperature of mass m by (T.

(1)

The SI unit of specific heat is J/kg K. Heat is so frequently measured in calories, therefore the practical unit cal/g C is also used quite often. The specific heat capacity of water is approximately 1 cal/g (C.

From Eq. (1), we can define the specific heat of a substance as the amount of energy needed to raise the temperature of unit mass of that substance by 1(C (or 1 K). A closely related quantity is the Molar heat capacity C. It is defined as,

(2)

where n is the number of moles of the substance. If M is the molecular mass of the substance, then n = were m is the mass of the substance and,

C =

(3)

The SI units of C is J / mole K.

Key points:

(a) It depends on nature of material of body. Dulong and petit has found formula for elemental solids that (with few exceptions such as carbon)

Atomic weight ( Specific heat ( 6 cal / oC

So, heavier the element lesser will be the specific heat, i.e., CHg < CCu< CAl(b) Specific heat of a substance also depends on temperature (particularly at low temperatures) the variation of specific heat with temperature for wateris shown in Fig (A) for metals in Fig (B). This temperature dependence of specific heat is usually neglected.

Fig. (A) WaterFig. (B) Metals

(c) Specific heat also depends on the state of substance, i.e., solid, liquid or gas. e.g., specific heat of solid copper will be different from that of liquid copper. In case of waterSpecific heat ofIn cal/g (CIn SI units, i.e., J/kg K

Ice (solid)0.52100

Water (liquid)14200

Steam (gas)0.471970

(d) If a substance is undergoing change of state which takes place at constant temperature (called isothermal change) , specific heat

( (

[as (T = 0]

i.e., specific heat of a substance at its melting pint or boiling point or isothermal change is infinite.

(e)Specific heat is found to be maximum for hydrogen (3.5 cal/gm (C) then for water (1 cal/gm (C = 4200 J/kg K). For all other substances specific heat is lesser than 1 cal/gm (C and is minimum for radon and actinium (= 0.22 cal/gam (C)

(f)If the temperature of a body changes without transfer of heat with the surroundings (adiabatic change) as in shaking a liquid or compressing a gas,

c = = 0

[as Q = 0]

i.e., specific heat of a substance, when it undergoes adiabatic change, is zero.

(g)Specific heat of a substance can also be negative. Negative specific heat means that in order to raise the temperature, a certain quantity of heat is to be withdrawn from the body. Specific heat of saturated water vapours is negative.

(h)When specific heats are measured, the values obtained are also found to depend on the conditions of the experiment. In general measurements made at constant pressure are different from those at constant volume. For solids and liquids this difference is very small and usually neglected. The specific heat of gases are quite different under constant pressure condition (cp) to constant volume condition (cv).

(i)As by definition c = (Q/m (T), heat required to change the temperature of m gm of a substance through (T:

Q = mc (T

and as (T = (Q/mc), greater the specific heat of a substance lesser will be the change in temperature for a given mass when same amount of heat is supplied. Now as specific heat of water is very large (1 cal/g (C), by absorbing or releasing large amount of heat its temperature changes by small amounts. This is why, it is used in hot water bottles or as coolant in radiators. This is also how the sea moderates the climate of nearby coastal land.

4. WATER EQUIVALENT

Waterequivalent of a body is the mass of water which when given same amount of heat as to the body, changes the temperature of water through same range as that of the body, i.e.,

W = (m ( c) gm

The unit of water equivalent W is gm while its dimensions [M]. Units and dimensions of some physicalquantities used in heat are given below in a tabular form.

S. No.Physical quantitySymbolDimensionsUnits

SICGS

1.HeatQ[ML2T2]Joulecalorie

2.Specificheatc[L2T2(1]J/kg Kcal/gm C(

3.Molar sp. heatC[ML2T2(1(1]J/mol Kcal/mol C(

4.Latent heatL[L2T2]J/kgcal/gm

5.Thermal capacity Tc[ML2T2(1]J/Kcal/C(

6.Waterequivalent W[M]kggm

5. PHASE CHANGES AND LATENT HEAT

Suppose that we slowly heat a cube of ice whose temperature is below 0(C at atmospheric pressure, what changes do we observe in the ice? Initially we find that its temperature increases according to equation Q = mc(T2 T1). Once 0(C is reached, the additional heat does not increase the temperature of the ice. Instead, the ice melts and temperature remains at 0(C. The temperature of the water then starts to rise and eventually reaches 100(C, whereupon the water vaporizes into steam at this same temperature.

During phase transitions (solid to liquid or liquid to gas) the added heat causes a change in the positions of the molecules relative to one another, without affecting the temperature.

The heat necessary to change a unit mass of a substance from one phase to another is called the latent heat (L). Thus, the amount of heat required for melting and vaporizing a substance of mass m are given by,

Q = mL

(1)

For a solid-liquid transition, the latent heat is known as the latent heat of fusion (Lf) and for the liquid-gas transition, it is known as the latent heat of vaporization (Lv).

6. PRINCIPLE OF CALORIMETRY

When two bodies (one being solid and other liquid or both being liquid) at different temperatures are mixed, heat will be transferred from body at higher temperature to body at lower temperature till both acquire same temperature. The body at higher temperature releases heat while body at lower temperature absorbs it, so that:

Heat lost = Heat gained,

i.e. principle of calorimetry represents the law of conservation of heat energy.

While, using this principle always keep in mind that:

(a) Temperature of mixture (T) is always ( lower temperature (TL) and ( higher temperature (TH), i.e.,

TL ( T ( TH

i.e. the temperature of mixture can never be lesser than lower temperatures (as a body cannot be cooled below the temperature of cooling body) and greater than higher temperature (as a body cannot be heated above the temperature of heating body when there is no chemical reaction).

(b)When temperature of a body changes, the body releases heat if its temperature falls and absorbs heat when its temperature rises. The heat released or absorbed by a body of mass m is given by:

Q = mc (T

Where c is specific heat of the body and (T change in its temperature in C( or K.

(c)When state of a body changes, change of state takes place at constant temperature [m.pt. or b.pt.] and heat released or absorbed is given by

Q = mL

Where L is latent heat. Heat is absorbed if solid converts into liquid (at m.pt.) or liquid converts into vapours (at b.pt.) and is released if liquid converts into solid or vapours converts into liquid.

HEAT TRANSFER

Heat can be transferred from one place to the other by any of three possible ways: conduction, convection and radiation. In the conduction, convection processes, a medium is necessary for the heat transfer. Radiation, however, does no have this restriction. This is also the fastest mode of heat transfer, in which heat is transferred from one place to the other in the form of electromagnetic radiation.

(i)Conduction

Figure shows a rod whose ends are in thermal contact with a hot reservoir at temperature T1 and a cold reservoir at temperature T2. The sides of the rod are covered with insulating medium, so the transport of heat is along the rod, not through the sides. The molecules at the hot reservoir have greater vibrational energy. This energy is transferred by collisions to the atoms at the end face of the rod. These atoms in turn transfer of heat through a substance in which heat is transported without direct mass transport is called conduction.

Most metals use another, more effective mechanism to conduct heat. The free electrons, which move throughout the metal can rapidly carry energy from the hotter to cooler regions, so metals are generally good conductors of heat. The presence of free electrons also causes most metals to be good electrical conductors. A metal rod at 5(C feels colder than a piece of wood at 5(C because heat can flow more easily from your hand into the metal.

Heat transfer occurs only between regions that are at different temperature, and the rate of heat flow is . This rate is also called the heat current, denoted by H. Experiments show that the heat current is proportional to the cross-section area A of the rod and to the temperature gradient , which is the rate of change of temperature with distance along the bar. In general

H =

(1)

The negative sign is used to make a positive quantity since is negative. The constant k, called the thermal conductivity is measure of the ability of a material to conduct heat.

A substance with a large thermal conductivity k is a good heat conductor. The value of k depends on the temperature, increasing slightly with increasing temperature, but k can be taken to be practically constant throughout a substance if the temperature difference between its ends is not too great.

Let us apply Eq. (1) to a rod of length L and constant cross sectional area A in which a steady state has been reached. In a steady state the temperature at each point is constant in time. Hence,

Therefore, the heat (Q transferred in time (t is

(2)

Thermal Resistance (R)

Eq. (2) in differential form can be written as

(3)

Here, (T = temperature difference (T.D) and

= thermal resistance of the rod.

(ii)Convection

Although conduction does occur in liquids and gases also, heat is transported in these media mostly by convection. In this process, the actual motion of the material is responsible for the heat transfer. Familiar examples include hot-air and hot-water home heating systems, the cooling system of an automobile engine and the flow of blood in the body.

You probably have warmed your hands by holding them over an open flame. In this situation, the air directly above the flame is heated and expands. As a result, the density of this air decreases and then air rises. When the movement results from differences in density, as with air around free, it is referred to as natural convection. Air flow at a beach is an example of natural convection. When the heated substance is forced to move by a fan or pump, the process in called forced convection. If it were not for convection currents, it would be very difficult to boil water. As water is heated in a kettle, the heated water expands and rises to the top because its density is lowered. As the same time, the denser, cool water at the surface sinks to the bottom of the kettle and is heated. Heating a room by a radiator is an example of forced convection.

Ingen Hausz Experiment:

Ingen Hausz provided a method to compare the thermal conductivities of different materials. He took wax coated rods of different materials but of the same area. One end of the rods is kept in a hot water bath and the other end is kept at the temperature of surroundings. If (1, (2, (3 . . . represent the lengths upto which the wax has melted and K1, K2, K3 . . . are their thermal conductivities, then

= . . . = constant

or

Example-6.A wall is made of two equally thick layers A and B of different materials. The thermal conductivity of A is twice that of B. In the steady state, the temperature difference across the wall is 36(C. The temperature difference across the layer A will be

Solution:

(iii)Radiation

The third means of energy transfer is radiation which does not require a medium. The best known example of this process is the radiation from sun. All objects radiate energy continuously in the form of electromagnetic waves. The rate at which an object radiates energy is proportional to the fourth power of its absolute temperature. This is known as the Stefans law and is expressed in equation form as

P = (AeT4Here P is the power in watts (J/s) radiated by the object, A is the surface area in m2, e is a fraction between 0 and 1 called the emissivity of the object and ( is a universal constant called Stefans constant, which has the value

( = 5.67 ( 108 W/m2-K4BLACK BODY RADIATION

(i)Perfectly black body

A body that absorbs all the radiation incident upon it and has an emissivity equal to 1 is called a perfectly black body. A black body is also an ideal radiator. It implies that if a black body and an identical another body are kept at the same temperature, then the black body will radiate maximum power as is obvious from equation p = ea(t4 also. Because e = 1 for a perfectly black body while for any other body e < 1.

Materials like black velvet or lamp black come close to being ideal black bodies, but the best practical realization of an ideal black body is a small hole leading into a cavity, as this Absorbs 98% of the radiation incident on them.

(ii)Absorptive power a

It is defined as the ratio of the radiant energy absorbed by it in a given time to the total radiant energy incident on it in the same interval of time.

As a perfectly black body absorbs all radiations incident on it, the absorptive power of a perfectly black body is maximum and unity.

(iii)Spectral absorptive power a(

The absorptive power a refers to radiations of all wavelengths (or the total energy) while the spectral absorptive power is the ratio of radiant energy absorbed by a surface to the radiant energy incident on it for a particular wavelength (. It may have different values for different wavelengths for a given surface. Let us take an example, suppose a = 0.6, a( = 0.4 for 1000 and a( = 0.7 for 2000 for a given surface. Then it means that this surface will absorbs only 60% of the total radiant energy incident on it. Similarly it absorbs 40% of the energy incident on it corresponding to 1000 and 70% corresponding to 2000 . The spectral absorptive power a( is related to absorptive power a through the relation

(iv)Emissive power e

(Dont confuse it with the emissivity e which is different from it, although both have the same symbols e).

For a given surface it is defined as the radiant energy emitted per second per unit area of the surface. It has the units of W/m2 or J/sm2. For a black body e=(T4.

(v)Spectral emissive power e(

It is emissive power for a particular wavelength (. Thus,

Kirchhoffs law: According to this law the ratio of emissive power to absorptive power is same for all surfaces at the same temperature.

Fig.

Hence,

but

(a)black body = 1

and

(e)black body = E(say)

Then,

Similarly for a particular wavelength (,

Here

E = emissive power of black body at temperature T

= (T4

From the above expression, we can see that

e( ( a(i.e., good absorbers for a particular wavelength are also good emitters of the same wavelength.

COOLING BY RADIATION

Consider a hot body at temperature T placed in an environment at a lower temperature T0. The body emits more radiation than it absorbs and cools down while the surrounding absorb radiation from the body and warm up. The body is losing energy by emitting radiations at a rate.

P1 = eA(T4

and is receiving energy by absorbing radiations at a rate

P2 = aA(T04

Here a is a pure number between 0 and 1 indicating the relative ability of the surface to absorb radiation from its surroundings. Note that this a is different from the absorptive power a. In thermal equilibrium, both the body and the surrounding have the same temperature (say Tc) and,

P1 = P2or

eA(Tc4 = aA(Tc4or

e = aThus, when T > T0, the net rate of heat from the body to the surroundings is,

eA( (T4 T04)

or

eA( (T4 T04)

Rate of cooling

or

( (T4 T04)

NEWTONS LAW OF COOLING

According to this law, if the temperature T of the body is not very different from that of the surroundings T0, then rate of cooling is proportional to the temperature difference between them. T0 prove it let us assume that

T = T0 + (TSo that

T4 = (T0 + (T)4 =

(from binomial expansion)

((T4 ) = 4 ((T)

or(T4 ) ( (T

(as T0 = constant)

Now, we have already shown that rate of cooling

and here we have shown that

,

if the temperature difference is small.

Thus, rate of cooling

or

as dT = d( or (T = ((

Variation of temperature of a body according to Newtons law

Suppose a body has a temperature (i at time t = 0. It is placed in an atmosphere whose temperature is (0. We are interested in finding the temperature of the body at time t, assuming Newtons law of cooling to hold good or by assuming that the temperature difference is small. As per this law,

rate of cooling ( temperature difference

or

or

Here ( = is a constant

(

(

From this expression we see that ( = (i at t = 0 and ( = (0 at t = (, i.e. temperature of the body varies exponentially with time from (i to (0 ( T1). The rate of heat transfer through the slab, in a steady state is f, with f equal to (see Fig.)

(A)1(B)1/2

(C)2/3(D)1/3

Solution:(C)

Let A be the area of each slab. In the steady state, the rate of heat flow through the composite slab is given by

(1)

Given l1 = x, l2 = 4x, K1 = K and K2 = 4K. Using these values in (1) we get

Comparing this with the given rate of heat transfer, we get f = . Hence the correct choice is (C).

6.

Three identical rods A,B and C of equal lengths and equal diameters are joined is series as shown in following fig. Their thermal conductivities are 2K,K and K/2 respectively. Calculate the temperature at two junction points.

(A)85.7, 57.1(C(B)80.85, 50.3(C

(C)77.33, 48.3(C(D)75.8,49.3(C

Solution:(A)

ith 1 = ith 2 = ith 3

(100 T1) = (T1 T2) =

T1 =

(100 T1) =

rT1 = = 85.7(C and T2 = = 57.1(C

7:

Three rods made of the same material ane having the same cross-section have been joined as shown in. Each rod is of the same length. The left and right ends are kept at 0(C and 90(C respectively. The temperature of the junction of the three rods

(A)45(C(B)60(C

(C)30(C(D)20(C

Solution:

I=I1+I2

or3T = 180(C or T = 60(C

8:

A solid copper sphere (density p and specific heat C) of radius r at an initial temperature 200 K is suspended inside a chamber whose walls are at almost 0 K. What is the required for temperature of the sphere to drop to 100 K?

(A)

(B)

(C)

(D)

Solution:(A) According to Stefans law P = eA(T4

EMBED Equation.DSMT4

or

ort = seconds

9:

A double pane window used for insulating a room thermally from outside consists of two glass sheets each pf area 1 m2 and thickness 0.01 m separated by a 0.05 m thick stagnant air space. In the steady state the room glass interface and glass outdoor interface are at 27(C and 0(C respectively. Calculate the rate of flow of heat through the windowpane. Also find the flow of heat through the windowpane. Also find the temperature of other interface if, conductivities of glass and air are 0.8 and 0.08 Wm-1 K-1 respectively.

(A)0.72(C(B)0.52(C

(C)0.192(C(D)0.32(CSolution:(B)

Req = =

EMBED Equation.DSMT4

A = 1 m2 Req =

= 41.5 W

41.5 = 0.8 (12 or (1 = 26.48(C

41.5 = or (2 = 0.52(C

10:

A space object has the space of a sphere of radius R. Heat sources ensure that the heat evolution at a constant rate is distributed uniformly over its volume. The amount of heat liberated by a thermodynamic temperature. In what proportion would the temperature of the object change if its radius is decreased to half?

(A)2.19(B)5.19

(C)1.19(D)4.19Solution:(C)Heat liberated (R3 and R2T4

OrT4 ( R

Thus

=

OrT2 = T1 orT2 =

That is , temperature decreases by a factor of 1.19.

11:

The room temperature is +20(C when outside temperature is -20(C and room temperature room temperature is + 10(C when outside temperature is -40(C. Find the temperature of the radiator heating the room.

(A)30(C(B)60(C

(C)90(C(D)45(CSolution:(B) Applying Newtons law

In case (1)

K1(T-Tr1)= K2(Tr2-Tout 1)

And in case (2)

K1(T-Tr2)= K2(Tr2-Tout 2)

Dividing these equations

orT=60(C

12:

Some water at 0(C is placed in a large insulated enclosure (vessel). The water vapour formed is pumped out continuously. What fraction of the water will ultimately freeze, if the latent heat vaporization is seven times the latent heat of fusion?

(A)7/8(B)8/7

(C)3/8(D)5/8Solution:(A) m = mass of water, f = fraction which freezes

L1 = latent heat of vaporization

L2 = latent heat of fusion ( L1 = 7L2

Mass of water frozen = mf

Heat lost by freezing water = m fL2

Mass of vapour formed = m(1 - f)

Heat gained by vapour = m (1 f) L1

mfL2 = m (1 - f) x 7L2

f = 7 7f or f = 7/8

13.

A substance is in the solid form at 0(C. The amount of heat added to this substance and its temperature are plotted in the following graph. If the relative specific heat capacity of the solid substance is 0.5, find from the graph, the mass of the substance is

(Specific heat capacity of water = 1000 cal kg-1 K-1 )

(A)0.02 kg(B)2 kg

(C)0.04 kg(D)0.05 kg14.

A substance is in the solid form at 0(C. The amount of heat added to this substance and its temperature are plotted in the following graph. If the relative specific heat capacity of the solid substance is 0.5, find from the graph, the specific latent heat of the melting process is

(Specific heat capacity of water = 1000 cal kg-1 K-1 )

(A) 6000 cal kg-1(B)4000 cal kg-1

(C) 1000 cal kg-1(D)2000 cal kg-115.

A substance is in the solid form at 0(C. The amount of heat added to this substance and its temperature are plotted in the following graph. If the relative specific heat capacity of the solid substance is 0.5, find from the graph, the specific heat of the substance in the liquid state is

(Specific heat capacity of water = 1000 cal kg-1 K-1 )

(A)300 cal kg 1 K-1(B)500 cal kg 1 K-1

(C)700 cal kg 1 K-1(D)100 cal kg 1 K-1Solution 13:

(A) 800 calories of heat raise the temperature of the substance from 0(C to 80(C.

( 800 = m (1000 ( 0.5 ) ( 80

( specific heat = relative sp. heat x sp. heat of water)

or m = 0.02 kg

Solution 14:

(B) Latent heat = 200 ( 4 = 800 cal ( 1 div reads 200 cal )

= 0.02 ( L

( L= 4000 cal kg-1

Solution 15:

(C) In the liquid state temperature rises from 80(C to 120(C, that is,

by 40(C after absorbing (2160 1600) cal.

0.02 s ( 40 = 2160 1600

or s = 700 cal kg 1 K-1

16:

An earthenware vessel loses 1g of water per second due to evaporation. The water equivalent of the vessel is 0.5 kg and the vessel contain 9.5 kg of water. Find the time required for the water in the vessel to cool to 28(C from 30(C. Neglect radiation losses. Latent heat of vaporization of water in this range of temperature is 540 cal g-1 .

(A)2 min 5 s(B)3 min 5 s

(C)5 min 3 s(D)6 min 2 s

Solution: (B) Here water at the surface is evaporated at the cost of the water in the vessel losing heat.

Heat lost by the water in the vessel

= (9.5 + 0.5) ( 1000 ( (30 20) = 105 cal

Let t the required time in seconds.

Heat gained by the water at the surface

= (t ( 10-3) ( 540 ( 103

(( L = 540 cal g-1 = 540 ( 103 cal kg-1)

( 105 = 540 t or t = 185 s = 3 min 5 s

17:

In an industrial process 10 kg of water per hour is to be heated from 20(C to 80(C. To do this, steam at 150(C is passed from a boiler into a copper coil immersed in water. The steam condenses in the coil and is returned to the boiler as water at 90(C. How many kg of steam are required per hour? Specific heat of steam = 1 kilo cal kg1(C1. Latent heat of steam = steam = 540 kilo cal kg1.(A)1 kg(B)2 kg

(C)3 kg(D)4 kg

Solution:(A) Let the mass of steam required per hour be m kg. Heat gained by water in boiler per hour is = 10 kg ( 1 kilo cal kg1 (C1 ( (80 20)(C

= 600 kilo cal

(1)

Heat lost by steam per hour is

= heat needed to cool m kg of steam from 150(C to 100(C + heat needed to convert m kg of steam at 100(C into water at 100(C + heat needed to cool m kg of steam at 100(C to 90(C

= m ( 1 ( (150 100) + m ( 540 + m ( 1 ( (100 90)

= 50 m + 540 m + 10 m

= 600 m kilo cal

(2)

Heat lost = heat gained. Equating (1) and (2) we have

600 m = 600

or m = 1 kg

18:

A closed cubical box made of a perfectly insulating material has walls of thickness 8 cm and the only way for the heat to enter or leave the box is through two solid cylindrical metal plugs, each of crosssectional area 12 cm2 and length 8 cm fixed in the opposite walls of the box. The outer surface A of one plug is kept at a temperature of 100(C while the outer surface of the other plug is maintained at a temperature of 4(C. The thermal conductivity of the material of the plug is 0.5 cal cm1 s1 ((C)1. A source of energy generating 36 cal s1 is enclosed inside the box. Find the equilibrium temperature of the inner surface of the box assuming that it is the same at all points on the inner surface.

(A)70(C(B)45(C

(C)65(C(D)76(C

Solution:(D) At equilibrium, the total energy generated by the source per second must equal the heat leaving per second through the two metal plugs (Fig.). Let T(C be the equilibrium temperature. Then heat leaving the box per second through surface A

= cal s1

and heat leaving the box per second through the surface B

Hence (T 100 + T 4) = 36

or 2T 104 = == 48 or T = 76(C

19:

Find the time during which a layer of ice of thickness 2.0 cm on the surface of a pond will have its thickness increased by 2 mm when the temperature conductivity of ice = 5 ( 10-3 cal cm-1 s-1 ((C)-1, density of ice at 0(C = 0.91 g cm-3 and latent heat of fusion = 80 cal g-1

(A)6 min 5 s(B)2 min 6 s

(C)5 min 6 s(D)3 min 5 sSolution:(C) substituting the given quantities in the expression

t = (-)

we have

t = [(2.2)2-2.0)2] = 306 s = 5 min 6 s.

20:

Water is being boiled in a flat-bottomed kettle placed on a stove. The area of the bottom is 300 cm2 and the thickness is 2 mm. If the amount of steam produced is 1 g/min, calculate the difference of temperature between the inner and other outer surfaces of the bottom. The thermal conductivity of the material of kettle = 0.5 cal cm-1 s-1 ((C)-1 and the latent heat of stem = 540 cal g-1.

(A)0.012 (C(B)0.0.04 (C

(C)0.02 (C(D)0.0.08 (CSolution:(A) If (T is the temperature difference between the inner ad outer surface of the bottom of the kettle, then the amount of heat flowing through the bottom per second is

= 750 ( cal per second (1)

But

(2)

Equating (1) and (2), we have

750 (T = 9 or (T = = 0.012 (C

21:

If an anisotropic solid has coefficients of linear expansion (x, (y and (z for three mutually perpendicular directions in the solid, what is the coefficient of volume expansion for the solid?

(A)( ( (x + (y + (z(B)( ( (2x + (y + (z

(C)( ( (2x + (2y + (2z(D)( ( (3x + (3y + (3zSolution:(A) Consider a cube, with edges parallel to X, Y, Z of dimension L0 at T = 0. After a change in temperature (T = (T 0), the dimensions change to

Lx = L0 (1 + (xT)Ly = L0(1 + (yT)Lz = L0(1 + (zT)

and the volume of the parallelepiped is

V = V0 (1 + (xT)(1 + (yT)(1 + (zT) ( V0 [1 + ((x + (y + (z)T]

Where V0 = . Therefore, the coefficient of volume expansion is given by

( ( (x + (y + (z.

22.

In aluminum sheet there is a hole of diameter 2m and is horizontally mounted on a stand. Onto this hole an iron sphere of radius 2.004 m is resting. Initial temperature of this system is 25 C. Find at what temperature, the iron sphere will fall down through the hole in sheet. The coefficients of linear expansion for aluminum and iron are 2.4 ( 104and 8.6 ( 10 5 respectively.

(A)82(C(B)43(C

(C)45(C(D)15(CSolution:(B) As value of coefficient of linear expansion for aluminum is more than that for ion, it expends faster then iron. So at some higher temperature when diameter of hole will exactly become equal to that of iron sphere, the sphere will pass through the hole. Let it happen at some higher temperature T. Thus we have at this temperature T,

(diameter of hole)Al = (diameter of sphere)iron

2[1 + (Al (T 25)] = 2.004[1 + (iron(T 25)]

2Al (T 25) = 0.004 + 2.004 (iron (T 25)

or

or

orT = 43(C23.

An iron ball has a diameter of 6 cm and is 0.010 mm too large to pass through a hole in a brass plate when the ball and plate are at a temperature of 30(C. At what temperature, the same for ball and plate, will the ball just pass through the hole?

(A)23.8(C(B)13.8(C

(C)53.8(C(D)83.8(CSolution:(C) We let I stand for the iron ball and B stand for the brass plate. LI = 6 cm and LI LB = 0.001 cm at t = 30(C. Since the brass plate expands uniformly, the hole must expand in the same proportion. Then heating both the ball and the plate leads to increases in the diameters of the ball and the hole, with the hole increasing more, since (B > (I. We require (LB (LI = 0.001 cm. (LB = (BLB (t; (LI = (ILI (t. We can approximate LB in this formula by 6 cm = LI. Then

(LB (LI = ((B (I)LI (t = 0.001 cm

solving, (t = 23.8(C, and finally t = 30(C + 23.8(C = 53.8(C24.

It is desired to put an iron rim on a wooden wheel. The diameter of the wheel is 1.1000m and the inside diameter of the rim is 1.0980 m. If the rim is at 20(C initially, to what temperature must it be heated to just fit onto the wheel?

(A)52(C(B)72(C

(C)102(C(D)152(CSolution:(D) ( for iron is found to be 1.2 ( 105 (C1.

(L = 1.1000 1.0980 = 0.0020 m = (L (t

0.0020 = (1.2 ( 105)(1.098) (t

(t + 20 = 172(C

(t = 152(C25.

Find the coefficient of volume expansion for an ideal gas at constant pressure.

(A)

(B)

(C)

(D)

Solution: (A) For an idea gas PV= nRT

As P is constant, we have

P.dV = nRdT

26.

What should be the lengths of steel and copper rod so that the length of steel rod is 5cm longer then the copper rod at all the temperatures. Coefficients of linear expansion for copper and steel are 1.7 and 1.1

(A)2.17, 14.17 cm(B)9.17, 14.17 cm

(C)9.17, 18.17 cm(D)3.17, 5.17 cmSolution:(B) It is given that the difference in length of the two rods is always 5 cm. Thus the expansion in both the rods must be same for all temperatures. Thus we can say that at all temperature differences, we have

or

[If l1 and l2 are the initial lengths of Cu and steel rods]

or

or

..(1)

It is given that l2 l1 = 5cm .(2)

or

Now from equation (2) l2 = 14.17 cm

27.

A steel wire of cross-sectional area 0.5 mm2 is held between two rigid clamps so that it is just taut at 20. Find the tension in the wire at 0. Given that Youngs modulus of steel is Yst = 2.1 ( 1012 dynes / cm2 and coefficient of linear expansion of steel is .

(A)2.31 ( 104(B)2.31 ( 102

(C)9.31 ( 106(D)2.31 ( 106Solution:(D) We know that due to drop in temperature, then tension increment in a clamped wire is

T = YA = 2.1 (1012 ( 0.5 ( 102 ( 1.1 ( 105 ( 20 = 2.31 ( 106

28.

Two bodies have the same heat capacity. If they are combined to form a single composite body, show that the equivalent specific heat of this composite body is independent of the masses of the individual bodies.

(A)

(B)

(C)

(D)

Solution:(C) Let the two bodies have masses m1, m2 and specific heats s1 and s2 then

m1s1 = m2s2orm1/m2 = s2/s1

Let s = specific heat of the composite body.

Then (m1 + m2) s = m1s1 + m2s2 = 2m1s1

s =

29.

20 gm steam at 100(C is let into a closed calorimeter of water equivalent 10 gm containing 100 gm ice at 10(C. Find the final temperature of the calorimeter and its contents. Latent heat of steam is 540 cal/gm, latent heat of fusion of ice=80 cal/gm, specific heat of ice = 0.5 cal/(C gm.

(A)13(C(B)63(C

(C)93(C(D)33(CSolution:(D) Heat lost by steam = mL + ms (100 - ()

where, ( is the equilibrium temperature

Heat lost by steam = 20 ( 540 + 20 ( 1 (100 - ()

= 10800 + 2000 - 20(

Heat gained by (ice + calorimeter) = 100 ( 80 + 100 ( 0.5 ( 10 + 100 ( (

Now

Heat lost = Heat gained

(10800 + 2000 20 ( = 8000 + 500 + 110 (

or 130( = 4300

or

( = = 33(C.

30.

Victoria Falls in Africa is 122 m in height. Calculate the rise in temperature of the water if all the potential energy lost in the fall is converted to heat.

(A)0.29 K(B)29 K

(C)0.69 K(D)0.99 KSolution:(A) Consider mass m of water falling.

mgy = mc (t gy = c (t

We express both sides in joules by noting

c = 1 kcal/kg ( K = 4184 J/kg ( K

Then

9.8(122) = 4184 (t

and

(t = 0.29 K

31.

An electric heater supplies 1.8 kW of power in the form of heat to a tank of water. How long will it take to heat the 200 kg of water in the tank from 10 to 70(C? Assume heat losses to the surroundings to be negligible.

(A)1.75 h(B)7.75 h

(C)4.75 h(D)5.75 hSolution: (B) The heat added is (1.8 kJ/s)t and the heat absorbed is

cm (T = (4.184 kJ/kg ( K) (200 kg)(60 K) = 5.0 ( 104 kJ

Equating heats, t = 2.78 ( 104 s = 7.75 h.

32.

What will be the final temperature if 50 g of water at 0(C is added to 250 g of water at 90(C?

(A)15(C(B)30(C

(C)45(C(D)75(C

Solution: (D) Heat gained = heat lost. (We assume no hat transfer to or from container.)

(50 g)(1.00 cal/g ( (C)(t 0(C) = (250 g)(1.00 cal/g ( (C)(90(C t)

where t is the final equilibrium temperature.

50t = 22500 250t

or300t = 22500

t = 75(C

33.

A 500 g piece of iron at 400(C is dropped into 800 g of oil at 20(C. If c = 0.40 cal/g((C for the oil, what will be the final temperature of the system. Assume no loss to the surroundings.

(A)15.7(C(B)30.7(C

(C)45.7(C(D)75.7(CSolution:(D) Heat lost = heat gained is written as

0.11(500)(400 t) = 0.40(800)(t 20)

from which t = 75.7(C

34.

A copper rod 2 m long has a circular cross section of radius 1 cm. One end is kept at 100(C and the other at 0(C, and the surface is insulated so that negligible heat is lost through the surface. Thermal conductivity of copper is 401 W/mK. Find the thermal resistance of the bar.

(A)15.9 K/W(B)20.9 K/W

(C)40.9 K/W(D)50.9 K/W35.

A copper rod 2 m long has a circular cross section of radius 1 cm. One end is kept at 100(C and the other at 0(C, and the surface is insulated so that negligible heat is lost through the surface. Thermal conductivity of copper is 401 W/mK. Find the thermal current H.

(A)1.3 watt(B)6.3 watt

(C)12.3 watt(D)18.3 watt36 .

A copper rod 2 m long has a circular cross section of radius 1 cm. One end is kept at 100(C and the other at 0(C, and the surface is insulated so that negligible heat is lost through the surface. Thermal conductivity of copper is 401 W/mK. Find the temperature gradient .

(A)10(C/m(B)40(C/m

(C)50(C/m(D)90(C/m37 .

A copper rod 2 m long has a circular cross section of radius 1 cm. One end is kept at 100(C and the other at 0(C, and the surface is insulated so that negligible heat is lost through the surface. Thermal conductivity of copper is 401 W/mK. Find the temperature 25 cm from the hot end.

(A)20.5(C(B)40.5(C

(C)77.5(C(D)87.5(CSolution 34 (A)Thermal resistance R =

orR = = 15.9 K/W

Solution 35 (B)Thermal current, H =

or

H = 6.3 watt

Solution 36 (C) Temperature gradient = = 50 K/m = 50(C/m

Solution 37 (D) Let be the temperature at 25 cm from the hot end, then

(( 100) = (temperature gradient) ((distance)

or( 100 = ( 50) (0.25)

or ( = 87.5(C38.

Two metal cubes with 3 cmedges of copper and aluminium are arranged as shown in figure. Thermal conductivity of copper is 401 W/mK and that of aluminium is 237 W/mK. Find the total thermal current from one reservoir to the other.

(A)0.14 K/W(B)0.34 K/W

(C)0.74 K/W(D)0.94 K/W39.

wo metal cubes with 3 cmedges of copper and aluminium are arranged as shown in figure. Thermal conductivity of copper is 401 W/mK and that of aluminium is 237 W/mK. Find the ratio of the thermal current carried by the copper cube to that carried by the aluminium cube.

(A)

0.75 K/W(B)0.05 K/W

(C)

0.15 K/W (D)0.35 K/WSolution: 38(A)Thermal resistance of aluminium cube R1 =

or R1 = = 0.14 K/W

Solution: 39(B)Thermal resistance of copper cube R2 =

or R2 = = 0.08 K/W

As these two resistances are in parallel, their equivalent resistance will be

R =

= = 0.05 K/W

40.

What temperature gradient must exist in an aluminum rod in order to transmit 8 cal/s per square centimeter of cross section down the rod? k for aluminum is 0.50 cal/s ( cm ( (C.

(A)36(C/cm(B)46(C/cm

(C)86(C/cm(D)16(C/cmSolution:(D) H = kA or 8 cal/s = (0.50 cal/s ( cm ( (C)(1 cm2)

= magnitude of temperature gradient = 16(C/cm.

The actual sign of the gradient depends on whether the heat flow is in the positive or negative x direction, being negative or positive for the two cases, respectively.

41.

What is heat conduction.

(A)(A (T)/d(B)(k (T)/d

(C)(kA (T)/d(D)((T)/dSolution:(C) The conduction equation, H ( (Q/(t = (kA (T)/d can be reexpressed as H = (T/R, where R ( d/(kA) is called the thermal resistance of the slab. It has units of K/W in SI.

42.

Consider the two insulating sheets with resistances R1 and R2 shown in Fig. What is the value of T' ?

(A)

(B)

(C)

(D)

Solution:(B) For the two sheets, H1 = (T1 T()/R1, H2 = (T( T2)/R2. Noting that H1 = H2 = H, we have (T1 T()/R1 = (T( T2)/R2. Cross multiplying we get R2(T1 T() = R1(T( T2), or rearranging terms, R2T1 + R1T2 = (R1 + R2)T(, and T = (R2T1 + R1T2)/(R1 + R2).

43.

A spherical blackbody of 5 cm radius is maintained at a temperature of 327(C. What is the power radiated?

(A)231 W(B)431 W

(C)531 W(D)631 WSolution:(A) The surface area of a sphere is 4(r2. In this case, then, the area is 4((25 ( 104) = 0.01(m2. The power radiated is given by Stefans law:

P= (T4A = (5.67 ( 108 W/m2.K4)(600 K)4(0.01( m2) = 231 W.

44..

A spherical blackbody of 5 cm radius is maintained at a temperature of 327(C. What wavelength is the maximum wavelength radiated.

(A)2.82 (m(B)4.82 (m

(C)3.82 (m(D)5.82 (mSolution:(B) The surface area of a sphere is 4(r2. In this case, then, the area is 4((25 ( 104) = 0.01(m2. The power radiated is given by Stefans law:

P= (T4A = (5.67 ( 108 W/m2.K4)(600 K)4(0.01( m2) = 231 W

By Wiens law, (m(600 K) = 2898 (m.K and (m = 4.82 (m.

45.

A sphere of 3 radius acts like a blackbody. It is equilibrium with its surroundings and absorbs 30 kW of power radiated to it from the surroundings. What is the temperature of the sphere?

(A)2300 K(B)2800 K

(C)3000 K(D)2600 KSolution:(D) The power absorbed by a blackbody is Pa = (A, or (30 ( 103 W)= (5.67 ( 108 W/m2.K4) 4((0.03 m)2.

= 4.68 ( 1013; Ta = temperature of surroundings = 2600 K. Since the body is in equilibrium with its surroundings, it is at the same temperature, 2600 K.

46 .

A blackbody is at a temperature of 527(C. To radiate twice as much energy per second, what temperature must be increased ?

(A)951 K(B)451 K

(C)551 K(D)651 K Solution:(A) Since P ( T4, the temperature must be increased to 21/4(800 K) = 951 K.

47.

Use Stefans law to calculate the total power radiated per square meter by a filament at 1727(C having an absorption factor of 0.4.

(A)0.16 MW/m2(B)0.26 MW/m2

(C)0.36 MW/m2(D)0.46 MW/m2Solution:(C) Stefans law gives R = ((T4 = 0.4(5.67 ( 108)(2000)4 = 0.36 MW/m2

48.

A blackbody is at a temperature of 527(C. To radiate twice as much energy per second, how many times of increase in radiated power when the temperature of a blackbody is increased from 7 to 287(C.

(A)5 times(B)16 times

(C)6 times(D)20 times Solution:(B) Since P ( T4, the temperature must be increased to 21/4(800 K) = 951 K.

And

times49. The initial and final temperature of water as recorded by an observer are (40.6 ( 0.2) C and (78.3 ( 0.3) C. Calculate the rise in temperature with proper error limit.

(A)(27.7 ( 0.5)C(B)(17.7 ( 0.5)C

(C)(37.7 ( 0.9)C(D)(37.7 ( 0.5)CSolution:(D) Let (1 = 40.6C, ((1 = ( 0.2 C

(2 = 78.3C, ((2 = ( 0.3 C

( ( = (2 (1 = 78.3 40.6 = 37.7C

& (( = ( (((1 + ((2) = ( (0.2 + 0.3) = ( 0.5C

Hence rise in temperature

= (37.7 ( 0.5)C

50.

A cylinder of radius R made of a material of thermal conductivity k1 is surrounded by a cylindrical sheet of inner radius R and outer radius 2R made of material of thermal conductivity

. The two ends of the combined system are maintained at two different temperatures. There is no loss of heat across the cylindrical surface and the system is in steady state. Calculate the effective thermal conductivity of the system.

(A)4K = 2K1 + 3K2

(B)4K = 5K1 + 3K2

(C) 4K = 6K1 + 4K2

(D)4K = K1 + 3K2Solution :(D) Two cylinders are in parallel, therefore equivalent thermal resistance R is given by

But

Here

and

i.e.4K = K1 + 3K2

51.

A lake is covered with ice 2 cm thick. The temperature of ambient air is (15oC. Find the rate of thickening of ice. For ice k = 4 ( 10(4k-cal-m(1s(1((C)(1. Density =9(103 kg/m3and latent heat L = 80 Kilo Cal/Kg.

(A) 2.5 cm/ hour

(B)1.5 cm/ hour

(C) 3.5 cm/ hour

(D)4.5 cm/ hourSolution : (B) Heat energy flowing per sec is given by

. . . (I)

if dm mass of ice is increased in time dt, then

Since,

. . . (ii)

From eq. (I) and (II)

Rate of thickening of ice = dx/dt

=

=

= 4.166 ( 10(6 m/s = 1.5 cm/ hour.

52.A body cools from 60(C to 50(C in 10 minutes. If the room temperature is 25(C and assuming Newtons law of cooling to hold good, find the temperature of the body at the end of the next 10 minutes.

(A) 42.85(C

(B)12.85(C

(C) 20.85(C

(D)52.85(CSolution :(A) According to Newtons law of cooling rate of loss of heat ((T ( To)

where T = mean temperature of the body

(

. . . (1)

Also, (

. . . (2)

where T is the required temperature

Solving both equation, we get,

T = 42.85(C

53. Two bodies A and B have thermal emissivities of 0.01 and 0.81 respectively. The outer surface areas of the two bodies are same. The two bodies emit total radiant power at the same rate. The wavelength (B corresponding to maximum spectral radiancy in the radiation from B is shifted from the wavelength corresponding to maximum spectral radiancy in the radiation from A by 1.00 (m. If the temperature of A is 5802 K, calculate (a) the temperature of B and (b) wavelength (B.

(A)2000K, 1.6 ( m(B)3000K, 1.8 ( m

(C)1934K, 1.5 ( m(D)4000K, 1.9 ( m

Solution :(C) (a)According to stefans law the power radiated by a body is give by

According to the given problem, , with

So that

i.e,

or

(b)According to Wiens displacement law.

; i.e,

i.e, and also (B - (A = 1(m(given)

so

i.e.

54

A body which has a surface area 2.00 cm2 and a temperature of 727oC radiates energy at the rate of 5 W. What is its emissivity? (Stefan boltzman constant ).

(A)0.14(B)0.44

(C)0.34(D)0.24solution:

(B)

(

55.Two rods of equal cross-sectional area A and length L are joined and what is the temperature of junction as shown in the figure. The temperature of one end of the composite rod is C and the other end of the rod is at . Draw a graph showing the variation of the temperature with the

distance x from the end maintained at . Assume that the flow is longitudinal and there is no loss of heat from the lateral surface.(A)

(B)

(C)

(D)

solution:(A)

(

when x ( L

(

The graph is as shown

56.

Two spherical soap bubbles coalesce to form a bigger bubble without any leakage of air. If V is the total change in volume of the contained air and S the total change in surface area, what is the value of 3PV + 4ST, where T is the surface tension of the soap solution and P is the atmospheric pressure.

(A)0(B)1

(C)2(D)3solution:(A) Let r1 and r2 be the initial radii of two bubbles and r is the final radius of the bubble after they coalesce. Then

(

(1)

also = change in total volume (2)

and = change in surface area (3)

from (1), (2) & (3) we get

57.

The graphs gives the variation of temperature of two bodies having the same surface area with time where Ax and Ay represent absorptivity and (x and (y represent emissivity then

(A) (x > (y and Ax < Ay

(B) (x < (y and Ax > Ay

(C) (x > (y and Ax > Ay

(D) (x < (y and Ax < Ay

solution:(D)According to Kirchoffs law good emitter is a good absorber

( Ey > Ex and Ay > Ax58. The temperature gradient in a rod of 0.5 m length is 80oC/m. If the temperature of hotter end of the rod is 30oC, then the temperature of the cooler end is

(A)40oC(B)10oC

(C)10oC(D)0oC.

Solution: (B)

59.A body at 300oC radiates 10 J cm2 s1. If Sun radiates 105 J cm2 s1, then its temperature is

(A)3000oC(B)5457oC

(C)300 104 oC(D)5730oC

Solution : (B)

60.The ratio of energy of radiation emitted by a black body at 27oC and 927oC is

(A)1 : 4 (B)1 : 16

(C)1 : 64(D)1 : 256.Solution:(B)E=T4

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

EMBED Visio.Drawing.6

SRI BHARADWAJ EDU GENEAPage 207

_1185791575.unknown

_1185792990.unknown

_1186841773.unknown

_1187100913.unknown

_1203179936.unknown

_1203608353.unknown

_1203608808.unknown

_1203609406.unknown

_1203782641.unknown

_1203782662.unknown

_1203609448.unknown

_1203609367.unknown

_1203608539.unknown

_1203608758.unknown

_1203608365.unknown

_1203181317.unknown

_1203183278.unknown

_1203183298.unknown

_1203183304.unknown

_1203181326.unknown

_1203179953.unknown

_1203181301.unknown

_1203179943.unknown

_1203176879.unknown

_1203179271.unknown

_1203179283.unknown

_1203179921.unknown

_1203179261.unknown

_1203176863.unknown

_1203176873.unknown

_1203176810.unknown

_1187102332.vsd

_1187019017.unknown

_1187020770.vsd

_1187026209.unknown

_1187100893.unknown

_1187025631.unknown

_1187024377.vsd

_1187019639.unknown

_1187019822.unknown

_1187019632.unknown

_1187003200.unknown

_1187003305.unknown

_1187015497.unknown

_1187015583.unknown

_1187017136.unknown

_1187015570.unknown

_1187003378.unknown

_1187003252.unknown

_1187003284.unknown

_1187003238.unknown

_1186997876.vsd

_1186998262.vsd

_1187002909.vsd

_1187002936.vsd

_1186999640.vsd

_1186997981.vsd

_1186925815.vsd

_1186926380.vsd

_1186996302.vsd

_1186842301.unknown

_1186912612.vsd

_1185793394.unknown

_1185811072.unknown

_1185811198.unknown

_1185812513.unknown

_1185812641.unknown

_1185812690.unknown

_1185813176.unknown

_1185813318.unknown

_1185812721.unknown

_1185812656.unknown

_1185812558.unknown

_1185811336.unknown

_1185811454.unknown

_1185811287.unknown

_1185811123.unknown

_1185811157.unknown

_1185811134.unknown

_1185811108.unknown

_1185811078.unknown

_1185810387.unknown

_1185810496.unknown

_1185810618.unknown

_1185811035.unknown

_1185810406.unknown

_1185794052.unknown

_1185809477.unknown

_1185810144.unknown

_1185807663.vsd

_1185794139.unknown

_1185793438.unknown

_1185793893.unknown

_1185793452.unknown

_1185793428.unknown

_1185793042.unknown

_1185793061.unknown

_1185793362.unknown

_1185793053.unknown

_1185793010.unknown

_1185793018.unknown

_1185792999.unknown

_1185792995.unknown

_1185792545.unknown

_1185792807.unknown

_1185792890.unknown

_1185792916.unknown

_1185792935.unknown

_1185792925.unknown

_1185792903.unknown

_1185792910.unknown

_1185792856.unknown

_1185792867.unknown

_1185792888.unknown

_1185792841.unknown

_1185792757.unknown

_1185792781.unknown

_1185792797.unknown

_1185792773.unknown

_1185792629.unknown

_1185792740.unknown

_1185792608.unknown

_1185792246.unknown

_1185792341.unknown

_1185792385.unknown

_1185792522.unknown

_1185792364.unknown

_1185792265.unknown

_1185792326.unknown

_1185792256.unknown

_1185791702.unknown

_1185792230.unknown

_1185792238.unknown

_1185791892.unknown

_1185792203.unknown

_1185791596.unknown

_1185791690.unknown

_1185791585.unknown

_1185469566.unknown

_1185790578.unknown

_1185791202.unknown

_1185791303.unknown

_1185791374.unknown

_1185791389.unknown

_1185791449.unknown

_1185791319.unknown

_1185791257.unknown

_1185791272.unknown

_1185791248.unknown

_1185790912.unknown

_1185790946.unknown

_1185791114.unknown

_1185790938.unknown

_1185790706.unknown

_1185790827.unknown

_1185790854.unknown

_1185790874.unknown

_1185790843.unknown

_1185790818.unknown

_1185790600.unknown

_1185790642.unknown

_1185790588.unknown

_1185790032.unknown

_1185790363.unknown

_1185790457.unknown

_1185790500.unknown

_1185790438.unknown

_1185790420.unknown

_1185790428.unknown

_1185790405.unknown

_1185790299.unknown

_1185790323.unknown

_1185790102.unknown

_1185790284.unknown

_1185790086.unknown

_1185726305.unknown

_1185783029.unknown

_1185788641.unknown

_1185788757.unknown

_1185789026.unknown

_1185788774.unknown

_1185788698.unknown

_1185783068.unknown

_1185727499.unknown

_1185782766.unknown

_1185726355.unknown

_1185726198.unknown

_1185726239.unknown

_1185717510.vsd

_1161246509.unknown

_1185289643.unknown

_1185353479.unknown

_1185461502.unknown

_1185467637.unknown

_1185467973.unknown

_1185468604.unknown

_1185462553.unknown

_1185461871.vsd

_1185355725.unknown

_1185355865.unknown

_1185355977.unknown

_1185447450.unknown

_1185355891.unknown

_1185355783.unknown

_1185355582.unknown

_1185292095.unknown

_1185315364.unknown

_1185319307.unknown

_1185292133.unknown

_1185314396.unknown

_1185314414.unknown

_1185292106.unknown

_1185289714.unknown

_1185292074.unknown

_1185289679.unknown

_1185030683.vsd

_1185097351.vsd

_1185113625.unknown

_1185280461.unknown

_1185289607.unknown

_1185132567.unknown

_1185280436.unknown

_1185120255.unknown

_1185098561.unknown

_1185099664.unknown

_1185099831.unknown

_1185113602.unknown

_1185099867.unknown

_1185099741.unknown

_1185099183.vsd

_1185099568.unknown

_1185098608.unknown

_1185098338.unknown

_1185035792.unknown

_1185097181.vsd

_1185097198.vsd

_1185035549.vsd

_1180710299.unknown

_1180713185.unknown

_1180713263.unknown

_1181055437.unknown

_1180710841.unknown

_1161250702.unknown

_1180710280.unknown

_1161250816.unknown

_1161246694.unknown

_1161247135.doc

T

x

L

2L

100oC

O

_1098364418.unknown

_1161170657.unknown

_1161177233.doc

A

A

k

2k

L

L

0oC

100oC

_1161177576.unknown

_1161246457.unknown

_1161177707.unknown

_1161177781.doc

k

2k

L

L

0oC

100oC

_1161177611.unknown

_1161177466.unknown

_1161177515.unknown

_1161177438.unknown

_1161170944.unknown

_1161177097.unknown

_1161177119.unknown

_1161177173.unknown

_1161170996.unknown

_1161170794.unknown

_1161170879.unknown

_1161170765.unknown

_1161169707.unknown

_1161169757.unknown

_1161169782.unknown

_1161169744.unknown

_1161089353.unknown

_1161158691.unknown

_1161166564.unknown

_1161166574.unknown

_1161159296.unknown

_1161158680.unknown

_1161089362.unknown

_1098430515.unknown

_1161085547.unknown

_1161085728.unknown

_1161089089.unknown

_1161085650.unknown

_1161085391.unknown

_1161085483.unknown

_1154270733.doc

t

T (

y

x

_1098430511.unknown

_997698371.unknown

_997789537.unknown

_1025184083.unknown

_1098194716.unknown

_1098198633.unknown

_1098194805.unknown

_1065962558.unknown

_999264822.unknown

_999265368.unknown

_997789759.unknown

_997790155.unknown

_997699066.unknown

_997709318.unknown

_997709585.unknown

_997699076.unknown

_997699262.unknown

_997698440.unknown

_997698850.unknown

_997698428.unknown

_997621903.unknown

_997622038.unknown

_997698203.unknown

_997621907.unknown

_997621870.unknown

_997621890.unknown

_997621778.unknown