toilet partition catalog - sccoe

Toilet Partition Catalog

2

PR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC YPR I VAC Y

Portfolio of Values

Architects, developers and facility managers have selected Bobrick’s performance-engineered toilet partitions with confidence since 1970. As a market leader, Bobrick delivers building owner value through design excellence, multiple options, code compliance, and long-lasting durability.

Specifiers choose from a variety of partition materials including Solid Color Reinforced Composite (SCRC), Compact Laminate (CL phenolic) and High Pressure Laminate (HPL) with a substantial selection of colors and patterns. Mounting configurations, Gap-Free® and Maximum Height privacy and hardware options are available.

SCRC, CL and HPL are first quality, extra-durable toilet partition materials that score exceptionally high for graffiti, impact and scratch-resistance. Excellent maintainability is another measure of durability and results in long-term performance, minimizing costly repair and replacement expense.

Partition hardware is fabricated of 50%–70% post-industrial recycled stainless steel. Regional manufacturing and distribution facilities within 500 miles of 70% of the U.S. population conserve transportation energy consumption. Bobrick’s Toilet Partitions can contribute to LEED points.

Bobrick toilet partitions comply with the latest ASTM E 84 Flame Spread and Smoke Development index requirements for Interior Finishes. Bobrick will gladly provide toilet partition accessibility consultation including wheelchair accessibility compartment layouts, approaches, turning radiuses and reach range compliance.

Cleanability is a key factor in maintaining partitions in a sanitary condition. CL and SCRC surfaces, including doors, stiles and panels, feature Graffiti-Off® non-porous surfaces for easy graffiti removal and disinfection. Other materials with porous textures make cleaning more difficult.

Architects and designers acknowledge that privacy is playing an increasingly vital role in washroom design. Bobrick answers these needs with privacy options on all of our toilet partitions.

Additional Bobrick Resources

Planning Guide for Accessible RestroomsThe Guide is the latest reference resource for ADAAG accessible restrooms, including

wheelchair turning radiuses, accessory mounting heights, reach ranges, and accessible toilet compartments.

Bobrick’s Restroom Accessory CatalogFeaturing hundreds of stainless steel accessories, including dispensers, receptacles, vendors, hand dryers, and grab bars, this catalog provides all

amenities required for the contemporary commercial restroom.

Bobrick’s Privacy Partition Brochure Bobrick now offers partitions utilizing FUNDERMAX® compact laminate (CL) for maximum height single panel width up

to 72" enabling architects and designers to create deeper stalls without sacrificing aesthetics or privacy.

3

Bobrick Toilet Partition Series Numerical Product Index

SierraSeries® (SCRC) - 1090 page 6 –7

DuraLineSeries® (CL) - 1080 8 –9

DesignerSeriesTM (HPL) - 1040 10

MetroSeriesTM (HPL) - 1550 11

TrimLineSeriesTM (HPL) - 1030 12

AccentSeriesTM (HPL) - 1530 13

BOBSpec is a systematic approach to Toilet Partition selection factors assuring the most appropriate partitions for a given project, efficient fabrication and successful installation.

BOBSpec assists architects, designers and developers, first in evaluating needs and priorities of a project, and then in selecting materials, configurations, design and privacy options, hardware and color/pattern choices.

BOBSpec results in delivering a concise specification reducing confusion and rework.

Toilet Partition Selection and Specification Method

Selecting, Specifying and Ordering Toilet Partitions for Each Building Type

1. Use the Material Selection Chart on page 5 to identify the most appropriate material and mounting configuration for the project.

2. Select the desired material from page 5 and pair it with the partition series height, privacy and hardware options.

3. Select the colors and patterns based on the design concept (SCRC page 7, CL page 9 and HPL page 14).

Prestige Properties

Standard Use Buildings

Heavy Traffic Facilities

Catalog Information

Symbols and Resources for Architects, Designers and Facility Managers

All Bobrick partitions are NFPA and ICC fire code compliant. Please refer to Bobrick’s TB-73 which provides Flame Spread and Smoke Developed indices. Test results available upon request.

The RapidqResponse® symbol signifies 2, 5 (1550 series) and 10-day shipping programs.

Bobrick.com is a world of electronic information and tools, including access to Bobrick’s global network of Representatives

Electronic Guide Specs and BIM Objects facilitate efficient project specification.

Spec Wizard aggregates selected Toilet Partition Series for a project into a comprehensive specification.

4

Bobrick’s Privacy Solutions

CONTINUOUS BRACKETS

Bobrick continuous panel bracket option allows for no line of sight at the panel connections.

TIGHTER GAPS

Bobrick made-to-order partitions allow for tighter gaps compared to industry standard.

GAP-FREE OPTION

Available on CL phenolic or SCRC, our Gap-Free option provides no sightlines between doors and stiles.

MAX HEIGHT OPTION

Doors and Panels available in 72" standard privacy height with 4-5/16" floor clearance. Custom heights also available. Contact your local representative for more details.

* Color shown FORMICA Wheat Strand 6212-58 with optional Occupancy Indicator Latch

Material Approx. Initial Cost/ Index Graffiti/Scratch Removal Notes

Oth

er M

anuf

actu

rers

Painted Metal

Lowest (1.0) Low scratch and moderate graffiti resistance

Paint or replacement required

Budget applications

Many feature standard plastic hinges

Class A Interior Finish Fire Code Classification

Plastic (HDPE)

Moderate (1.9) Low scratch and graffiti resistance

Low impact resistance

High traffic environments

Does not meet Interior Finishes Fire Code Classification. Be sure to specify the NFPA 286 test.

Stainless Steel

Highest (3.0) Low scratch and impact resistance

Moderate graffiti resistance

High Design look

Limited Finishes

Class A Interior Finish Fire Code Classification

Bob

rick

Mat

eria

ls Laminate (HPL)

Lowest (1.1) Low scratch and impact resistance

Graffiti can be removed

Budget for high-end applications depending on options selected

Concealed stainless steel hardware is standard for Bobrick partitions

Class B Interior Finish Fire Code Classification

Phenolic (CL)

Moderate (2.4) High scratch and impact resistance

Complete graffiti removal

Highest traffic environments

Many colors and patterns

Class A and B Interior Finish Fire Code Classification

SCRC

Moderate to High (2.7)

Highest scratch and impact resistance

Complete graffiti removal

High traffic and vandal-prone environments

4 Earthtone colors

Class B Interior Finish Fire Code Classification

Note: Urinal Screen Mounting Configurations are Wall-Hung, Post-to-Ceiling and Floor-Anchored.

Configuration Overhead-Braced Floor-to-Ceiling Floor-Anchored Ceiling-HungPoints of Attachment Two Points Two Points One Point One Point

Benefits Offers the most durable mounting configuration at a budget price.

Durable mounting option even without the headrail.

Superior design. Specify for low-traffic, non-vandal prone restrooms.

Contemporary appearance, provides clear access for floor maintenance.

Additional Information

Most specified toilet partition configuration.

A small premium compared to Overhead-Braced.

Anchored into a solid substrate.

Not appropriate for heavy-traffic, vandal-prone restrooms. (Requires additional structural support.)

Standard and Maximum Height Stiles

85" to top of stile Accommodates up to 120" ceiling height

70" to top of stile (standard), 76-5/16" to top of stile (max height)

Accommodates up to 120" ceiling height

Material Selection

Mounting Configuration Selection

5

6


Notes Options Price Index

RapidqResponse: 10-days or less, 4 earthtone colors, up to 25 compartments 25 -Year Warranty

Gap-Free Privacy Design

Maximum-Height Privacy

Heavy-Duty Continuous Stainless Steel Hardware

SCRC 2.7 CL 2.4HDPE 1.9

SierraSeries – Solid Color Reinforced Composite (SCRC) 1090

FeaturesSolid color-through material

Ultra-hard Graffiti-Off surfaces

Scratch, dent, moisture and impact-resistant

3/4" Doors/stiles and 1/2" panels

Through-bolted panel-to-stile bracket, keeper and robe hook

Class B ASTM E 84 Interior Wall and Ceiling Finish Classification

Emergency access doors

Material SpecificationsDyed wood fibrous material reinforced with polycarbonate and phenolic resins coated with a non-ghosting, graffiti-resistant surface thermoset and integrally fused into ahomogeneous piece.

* Color shown SCRC Forest Green SC04

Full-Height Mounting Bracket

Full-Height HingeAdjustable Partial or Self-Closing Hinges

Coat Hook

Latch and Keeper

7

(SCRC)

SCRC Standard Colors

Golden Khaki SCO1 Desert Beige SC02

Terra Cotta SC03 Forest Green SC04

Colors are printed reproductions and are for descriptive purposes only. Refer to manufacturer’s samples for absolute color fidelity. Color guides and samples are available from Bobrick on request. SCRC minor edge nicks and random color variations are normal consequences of manufacturing material containing natural fibers. Material can vary in color between thicknesses and production batches. Where color consistency is critical, Compact Laminate 1080 DuraLineSeries is recommended. Discoloration of the edges may occur in environments with significant light exposure. Visit bobrick.com for the latest colors and patterns.

TRESPA is a registered trademark of Trespa International BV.

SCRC Hardware Selection

Optional HardwareStandard Hardware

8


Note: 10-Day Program excludes Class A fire-rated 1180 Series and Maximum Height Options.


RapidqResponse: 10-days or less, 18 standard colors / patterns, up to 25 compartments.25-Year Warranty*FUNDERMAX single panel widths up to 72"

Gap-Free Privacy Design



SCRC 2.7 CL 2.4HDPE 1.9

DuraLineSeries – Compact Laminate (CL phenolic) 1080/1180

FeaturesDurable phenolic solid-core construction

Ultra-hard Graffiti-Off surfaces

Scratch, dent, moisture and impact-resistant

3/4" Doors/stiles and 1/2" panels

Concealed stainless steel hardware

Class A (1180 Series) and Class B (1080 Series) ASTM E 84 Interior Wall and Ceiling Finish Classification

Wide selection of colors and patterns


Single panel width up to 72" creating deeper stalls*

Material SpecificationsSolidly fused plastic laminate with matte-finish melamine surfaces; integrally bonded colored face sheets and black phenolic-resin core.

Color shown FUNDERMAX Brushed Aluminum 0328 FH


Full-Height Hinge

Optional HardwareStandard Hardware

Adjustable Partial or Self-Closing Hinges

Coat Hook

Latch and Keeper

9

(SCRC)

WHITE 949-58

FROSTY WHITE 1573-60

ALMOND S-445-CA

WILLOW GREY S-431-CA

**BRUSHED ALUMINUM 0328 FH

GREY GRIT P-886-CA

PEWTER MESH 4878-60

**SILVRETTA 0229 FH

EARTH 5342-58

EVENING TIGRIS 4674-60

**CELLO 0811 FH

LIMOUSINE GREY S-542-CA

NAVY GRAFIX 7018-58

CITADEL WARP 5882-58

GRAPHITE GRAFIX 515-58

**CHARCOAL 0077 FH

BLACK STONE P-500-CA

**BLACK 0080 FH

CL phenolic Standard Colors and Patterns

Hundreds of additional colors are available in Compact Laminate; additional lead time will apply, please consult ARBORITE®, FORMICA®, Wilsonart®, or FUNDERMAX® for color options. Colors are printed reproductions and are for descriptive purposes only. Refer to manufacturers’ samples for absolute color fidelity. Color guides and samples are available from Bobrick on request. Where color consistency is critical, compact laminate 1080 DuraLineSeries® is recommended. All colors are available in matte finish. Visit bobrick.com for the latest colors and patterns.

ARBORITE is a registered trademark of Weyerhaeuser NR Company. Wilsonart, is a registered trademark of Wilsonart International, Inc.; FORMICA and the FORMICA Anvil logo are registered trademarks of The Diller Corporation. © 2015 The Diller Corporation. FUNDERMAX is a registered trademark of FUNDERMAX GmbH.

** Standard color by FUNDERMAX allows for single panel width up to 72", eliminating use of additional hardware. Meets Class A fire rating without up-charge. See page 8 for design options.

CL phenolic Hardware Selection

Standard Steel-Core Stile


Full-Height Hinge

Optional Hardware

Standard Hardware


Coat Hook

Latch and Keeper

10


Note: 10-Day Program excludes Maximum Height Privacy. See page 14 for HPL color selections.


RapidqResponse: 10-days or less, 35 standard colors/patterns, up to 25 compartments2-Year Warranty

Maximum-Height PrivacyHeavy-Duty Continuous Stainless Steel Hardware

Stainless 2.7 Designer 1.9 Metro 1.2 Metal 1.0

DesignerSeries – High Pressure Laminate (HPL) 1040

FeaturesImpact and graffiti-resistant

1" Doors, stiles and panels




Standard steel-core stiles

Material Specifications High-pressure laminated plastic with a 45 lb density, industrial grade, resin-impregnated particle board substrate

Color shown FORMICA HPL Burnt Strand 6307-58

Standard Hardware

Adjustable Partial or Self- Closing Hinges

Coat Hook

Latch and Keeper

11

See page 14 for HPL color selections. *Includes colors/patterns stocked by Wilsonart and Formica. 2-days and 5-days valid in US only.

Notes Option Price Index

RapidqResponse: 2-days, 5-days* up to 15 compartments, 35 standard colors/patterns.2-year warranty

Stainless steel hardware Metro 1.2Metal 1.0

MetroSeries – High Pressure Laminate (HPL) 1550

FeaturesImpact and graffiti-resistant

1" Doors, Stiles and Panels




Material SpecificationsHigh-pressure laminated plastic with a 45 lb density, industrial grade, resin-impregnated particle board substrate.

Color shown FORMICA HPL Wheat Strand 6212-58

Standard Steel-Core Stile


Full-Height Hinge

Optional Hardware

Standard Hardware


Coat Hook

Latch and Keeper

12



RapidqResponse: 10-days or less, 35 standard colors/patterns, up to 25 compartments 5 -Year Warranty



TrimLine 2.7Stainless 2.7 Accent 1.7Metal 1.0

Note: 10-Day Program excludes Maximum Height Privacy. See page 14 for HPL color selections.

FeaturesStainless steel edge trim

Impact and graffiti-resistant





Standard steel-core stiles

Material SpecificationsHigh-pressure laminated plastic with a 45 lb density, industrial grade, resin-impregnated particle board substrate and stainless steel edge trim.

TrimLineSeries – High Pressure Laminate (HPL) 1030

Color shown Wilsonart HPL Designer White D354-60

Standard Hardware


Coat Hook

Latch and Keeper

13

Notes Price Index

RapidqResponse: 10-days, up to 15 compartments, 35 standard colors/patterns.5-year warranty

Accent 1.7 Metal 1.0

Note: See page 14 for HPL color selections.

FeaturesStainless steel edge trim

Impact and graffiti-resistant





Material SpecificationsHigh-pressure laminated plastic with a 45 lb density, industrial grade, resin-impregnated particle board substrate and stainless steel edge trim.

AccentSeries – High Pressure Laminate (HPL) 1530

Color shown Wilsonart HPL Hollyberry D307-60

14

*Premium colors carry an up-charge not to exceed 10% of total cost. Panels over 60" wide with directional patterns and finishes will be spliced, joining the 2 pieces on the particle board at an additional charge. HPL colors are printed reproductions and are for descriptive purposes only. Refer to manufacturer’s samples for absolute color fidelity. Color guides and samples are available from Bobrick on request. Lead-time for a substantial selection of stocked Wilsonart and FORMICA colors, on orders of up to 15 compartments, is 5 business days for 1550/1540 and 20 business days for 1530/1040/1030 after order approval. Visit bobrick.com for the latest colors and patterns.

Wilsonart is a registered trademark of Wilsonart International, Inc.; FORMICA, and the FORMICA Anvil logo are registered trademarks of The Diller Corporation. © 2015 The Diller Corporation.

Designer White D354-60 White Carrara 4924-38 Antique White 1572-60

Natural Almond D30-60 Beige 1530-60

Grey 1500-60 Satin Stainless 4830K-18*

Platinum D315-60 Desert Zephyr 4841-60

Natural Canvas 7022-58

Grey Nebula 4622-60 Pewter Mesh 4878-38 Evening Tigris 4674-60 Natural Tigris 4669-60 Wheat Strand 6212-58

Slate Grey D91-60 Shadow D96-60

Tungsten EV 4814-60 Spiced Zephyr 4859-60

Windswept Bronze 4794-60

Burnt Strand 6307-58 Graphite Nebula 4623-60

Green Tigris 4667-60 Chestnut Woodline 5884-58

Chocolate Warp 5881-58

Navy Grafix 7018-58 Brittany Blue D321-60

Smokey Brown Pear 5488-58 Figured Mahogany 7040A-60

Xanadu 7945K-38*

Spectrum Blue 851-58 Hollyberry D307-60

Leaf Green 8820-58 Basalt Slate 3690-58

Black 1595-60

HPL Standard Colors/Patterns

Configurations

Floor-Anchored Overhead-Braced Floor-to-Ceiling Ceiling-Hung

15

Material Solid Color Reinforced Composite (SCRC)

Compact Laminate (CL phenolic)

High Pressure Laminate (HPL)

High Pressure Laminate with Stainless Steel Edge Trim

SeriesSierra1090

DuraLine1080/1180

Designer1040

Metro1550

TrimLine1030

Accent1530

Floor- Anchored 1091 1081/1181 1041 1551 1031 1531

Overhead-Braced 1092 1082/1182 1042 1552 1032 1532

Floor-to- Ceiling 1096 1086/1186 1046 1556 1036 1536

Ceiling- Hung 1098 1088/1188 1048 1558 1038 1538

Height and Privacy Options

Sightline Privacy

Gap-Free

Add G suffix Example 1092G

Gap-Free

Add G suffix Example 1082G

N/A N/A N/A N/A

Maximum Height Privacy

72" Doors/Panels

Add 2 prefix Example 2092

72" Doors/Panels


72" Doors/Panels


N/A 72" Doors/Panels


N/A

Hardware Options

Vandal Resistant Panel Brackets

Continuous BracketsAdd .67P suffix Example 2092G.67P

Continuous BracketsAdd .67P suffix Example 2082G.67P

Continuous BracketsAdd .65P suffix Example 2042.65P

N/A Continuous BracketsAdd .65P suffix Example 2032.65P

N/A

Vandal Resistant Hinges

Continuous HingesAdd .67D suffix Example 2092G.67D

Continuous HingesAdd .67D suffix Example 2082G.67D

Continuous HingesAdd .65D suffix Example 2042.65D

N/A Continuous HingesAdd .65D suffix Example 2032.65D

N/A

Vandal Resistant Panel Brackets/ Hinges

Continuous Brackets/HingesAdd .67 suffix Example 2092G.67

Continuous Brackets/HingesAdd .67 suffix Example 2082G.67

Continuous Brackets/ HingesAdd .65 suffix Example 2042.65

N/A Continuous Brackets/ HingesAdd .65 suffix Example 2032.65

N/A

Bobrick Model and Series Number Reference Chart

U.S. CorporateOffices

818.982.9600 818.503.1102 [email protected] Tujunga Avenue North Hollywood, CA 91605-6213

www.bobrick.com

Canadian Offices

877.423.6555Eastern Canada

877.423.8555 [email protected] Rolark Drive Toronto, Ontario M1R 3B1

www.bobrick.com

877.423.6444Western Canada

877.423.8444 [email protected] www.bobrick.com

International Customer Service

Gamco A Division of Bobrick

+1.818.764.1000

818.982.9600

+1.818.503.9941

818.503.1102

[email protected] Tujunga Avenue North Hollywood, CA 91605-6213

[email protected] Gamco Place Durant, OK 74701-1910

www.bobrick.co.uk

www.gamcousa.com

Koala Kare ProductsA Division of Bobrick

888.733.3456 303.539.8399 [email protected] S. Quentin Street Centennial, CO 80112-3945

www.koalabear.com

CATALOG FORM NO. TP-2018, MAY 2018, 17M, © 2018, BOBRICK WASHROOM EQUIPMENT, INC.

5 © 2019 AS America Inc.spec_3451001 Madera FW 15Height-EL-Flushometer Rev 1 5/19

To Be Specified:❏ Color: ❏ White ❏ Seat: ❏ American Standard #5901.100 Heavy duty open front less cover ❏ American Standard #5905.100 Extra heavy duty open front less cover❏ Flushometer Valve:

❏ 1.6 gpf: ❏ Sensor-Operated: American Standard Selectronic® DC Power #6065.161.002 (Top Spud) ❏ Sensor-Operated: American Standard Selectronic® AC Power #6067.261.002 (Back Spud) ❏ Manual: American Standard #6047.161.002 (Top Spud) ❏ 1.28 gpf: ❏ Sensor-Operated: American Standard Selectronic®

DC Power #6065.121.002 (Top Spud) ❏ Sensor-Operated: American Standard Selectronic® AC Power #6067.221.002 (Back Spud) ❏ Manual: American Standard #6047.121.002 (Top Spud) ❏ 1.6 / 1.1 gpf Dual Flush: ❏ Sensor-Operated: American Standard Selectronic® DC Power #6065.761.002 (Top Spud)

Madera™ FloWise® 15" HeightElongated Flushometer Toilet

VITREOUS CHINA with EVERCLEAN®

Madera™ FloWise® 15" Height Elongated with EverClean®

• Floor mount flushometer valve toilet• Vitreous china• High Efficiency, Low Consumption. Operates in the range of 1.1 gpf to 1.6 gpf (4.2 Lpf to 6.0 Lpf) • Meets definition of HET (High Efficiency Toilet) when used with a high efficiency flush valve (1.28 gpf or 1.6 / 1.1 gpf dual flush)• Permanent EverClean® surface inhibits the growth

of stain and odor-causing bacteria, mold, and mildew on the surface

• Fully glazed 2-1/8" trapway• Elongated bowl• 10" or 12" roughing-in• 15" rim height• Condensation channel• Powerful direct-fed siphon jet action• 10" x 12" water surface area• 1-1/2" inlet spud• 2 bolt caps

❏ 3451001 Elongated bowl only, top spud❏ 3452001 Elongated bowl only, top spud with slotted rim for bedpan holding❏ 3453001 Elongated bowl only, back spud❏ 3455001 Elongated bowl only, back spud with slotted rim for bedpan holding

System MaP* Score: • 1,000 grams of miso @ 1.1 gpf, 1.28 gpf or 1.6 gpf

when used with an American Standard flush valve * Maximum Performance (MaP) testing performed by IAPMO

R&T Lab. MaP Report conducted by Veritec Consulting, Inc. and Koeller and Company.

Component Parts:❏ 047007-0070A Inlet Spud (furnished with bowl)❏ 481310-100 Bolt caps with retainers (furnished with bowl)

Nominal Dimensions:718 x 356 x 381mm(28-1/4" x 14" x 15")

Fixture only, less seat and flush valve

Recommended working pressure–between25 psi at valve when flushing and 80 psi static

Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.2 / CSA B45.1 for Vitreous China Fixtures

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

ENVIROMENTALPRODUCT

DECLARATION

EVERCLEAN WATER EFFICIENT

When used with1.1 or 1.28 gpf toilet flush valves

6 © 2019 AS America Inc.

Madera™ FloWise® 15" HeightElongated Flushometer Toilet


NOTES:PRODUCT 3451 AND 3453 SHOWN, 3452 AND 3455 SAME EXCEPT WITH SLOTTED RIM FOR BED PAN HOLDING.TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON THE FLUSHOMETER VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR SUPPLY ROUGHING.THIS TOILET DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 254MM (10") AND A MAXIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.FLUSHOMETER VALVE NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. FLUSHOMETER VALVE REQUIREMENTS FOR 12" (305MM) ROUGH-IN: SWEAT EXTENSION NIPPLE IS REQUIRED. REFER TO VALVE MANUFACTURER AND LOCAL CODES.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

1-1/2"SPUD

121mm(4-3/4") 673mm

(26-1/2")

254mm(10")

381mm(15")

470mm(18-1/2")

356mm(14")

362mm(14-1/4")

150mm(5-7/8")

254mm(10")

13mm(1/2")

25mm(1")

102mm(4")

718mm(28-1/4")

C/L OF SEAT POST HOLES140mm (5-1/2") CENTERS

FINISHED WALL

FINISHEDFLOOR

C/L OF OUTLET

1" N.P.T. OR 1" C.W.T. SUPPLYTO FLUSH VALVE

254mm(10")

381mm(15")

400mm(15-3/4")

470mm(18-1/2")

356mm(14")

362mm(14-1/4")

150mm(5-7/8")

254mm(10")

13mm(1/2")

76mm(3")

718mm(28-1/4")


FINISHED WALL

FINISHED FLOOR

C/L OF OUTLET

3451001 / 3452001

3453001 / 3455001

spec_3451001 Madera FW 15Height-EL-Flushometer Rev 1 5/19

M111 © 2018 AS America Inc.

To Be Specified:❏ Color: ❏ White❏ Seat: ❏ American Standard #5901.100 Heavy duty open front less cover ❏ American Standard #5905.100 Extra heavy duty open front less cover❏ Flushometer Valve:

❏ 1.6 gpf: ❏ Sensor-Operated: American Standard Selectronic® DC Power #6065.161.002 (Top Spud) ❏ Sensor-Operated: American Standard Selectronic® AC Power #6067.261.002 (Back Spud) ❏ Manual: American Standard #6047.161.002 (Top Spud) ❏ 1.28 gpf: ❏ Sensor-Operated: American Standard Selectronic®

DC Power #6065.121.002 (Top Spud) ❏ Sensor-Operated: American Standard Selectronic® AC Power #6067.221.002 (Back Spud) ❏ Manual: American Standard #6047.121.002 (Top Spud) ❏ 1.6 / 1.1 gpf Dual Flush: ❏ Sensor-Operated: American Standard Selectronic® DC Power #6065.761.002 (Top Spud)

Madera™ FloWise® 16-1/2" HeightElongated Flushometer Toilet


Madera™ FloWise® 16-1/2" Height Elongated with EverClean®

• Floor mount flushometer valve toilet• Vitreous china• High Efficiency, Low Consumption. Operates in the range of 1.1 gpf to 1.6 gpf (4.2 Lpf to 6.0 Lpf) • Meets definition of HET (High Efficiency Toilet) when used with a high efficiency flush valve (1.28 gpf or 1.6 / 1.1 gpf dual flush)• Permanent EverClean® surface inhibits the growth of stain and odor-causing bacteria, mold, and mildew on the surface• Fully glazed 2-1/8" trapway• Elongated bowl• 10" or 12" roughing-in• 16-1/2" rim height for accessible application• Condensation channel• Powerful direct-fed siphon jet action• 10" x 12" water surface area• 1-1/2" inlet spud• 2 bolt caps

❏ 3461.001 Elongated bowl only, top spud❏ 3462.001 Elongated bowl only, top spud with slotted rim for bedpan holding❏ 3465.001 Elongated bowl only, top spud with 4 bolts❏ 3466.001 Elongated bowl only, top spud with slotted rim for bedpan holding with 4 bolts❏ 3463.001 Elongated bowl only, back spud❏ 3464.001 Elongated bowl only, back spud with slotted rim for bedpan holding

System MaP* Score: • 1,000 grams of miso @ 1.1 gpf, 1.28 gpf or 1.6 gpf

when used with an American Standard flush valve * Maximum Performance (MaP) testing performed by IAPMO

R&T Lab. MaP Report conducted by Veritec Consulting, Inc. and Koeller and Company.

Component Parts:❏ 047007-0070A Inlet Spud (furnished with bowl)❏ 481310-100 Bolt caps with retainers (furnished with bowl)

Nominal Dimensions:718 x 356 x 419mm(28-1/4" x 14" x 16-1/2")

Fixture only, less seat and flush valveRecommended working pressure–between25 psi at valve when flushing and 80 psi static

Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.2 / CSA B45.1 for Vitreous China Fixtures


MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES - CHECK LOCAL CODES. When installed so top of seat is 432 to 483mm (17" to 19") from thefinished floor.

BARRIER FREE

spec_3461.001 Madera FW 16.5Height-EL-Flushometer 11/18

ENVIROMENTALPRODUCT

DECLARATION

ADA COMPLIANT

EVERCLEAN WATER EFFICIENTWhen used with

1.1 or 1.28 gpf toilet flush valves

M112 © 2018 AS America Inc.

NOTES:PRODUCT 3461 AND 3463 SHOWN, 3462 AND 3464 SAME EXCEPT WITH SLOTTED RIM FOR BED PAN HOLDING.TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON THE FLUSHOMETER VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR SUPPLY ROUGHING.THIS TOILET DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 254MM (10") AND A MAXIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.FLUSHOMETER VALVE NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. FLUSHOMETER VALVE REQUIREMENTS FOR 12" (305MM) ROUGH-IN: SWEAT EXTENSION NIPPLE IS REQUIRED. REFER TO VALVE MANUFACTURER AND LOCAL CODES.


254mm(10")

419mm(16-1/2")

438mm(17-1/4")

470mm(18-1/2")

356mm(14")

362mm(14-1/4")

150mm(5-7/8")

254mm(10")

13mm(1/2")

76mm(3")

718mm(28-1/4")


FINISHED WALL

FINISHED FLOOR

C/L OF OUTLET

711mm(28")

1-1/2"SPUD

121mm(4-3/4")

254mm(10")

419mm(16-1/2")

470mm(18-1/2")

356mm(14")

362mm(14-1/4")

150mm(5-7/8")

254mm(10")

13mm(1/2")

25mm(1")

102mm(4")

718mm(28-1/4")


FINISHED WALL

FINISHEDFLOOR

C/L OF OUTLET

1" N.P.T. OR 1" C.W.T. SUPPLYTO FLUSH VALVE

3461.001/3462.001

3465.001/3466.0014-BOLT ANCHOR DETAIL(Bottom View of Bowl)

3463.001/3464.001

Madera™ FloWise® 16-1/2" HeightElongated Flushometer Toilet


BARRIER FREE

spec_3461.001 Madera FW 16.5Height-EL-Flushometer 11/18

159mm(6-1/4")

512mm(20-1/4")

150mm(5-7/8")

12mm (1/2") HOLES

150mm(5-7/8")

M149 © 2018 AS America Inc.spec_6581.001 Maybrook EC 11/18

Maybrook® Universal Urinal

VITREOUS CHINA WITH EVERCLEAN®

Maybrook® Universal Urinalwith EverClean®

• Vitreous china• Ultra High Efficiency, Low Consumption. Operates in the range of 0.125 gpf to 1.0 gpf (0.5 Lpf to 3.8 Lpf)• Permanent EverClean® surface inhibits the growth of stain and odor causing bacteria, mold and mildew on the surface• Flushing rim• Washout flush action• Integral strainer• 3/4" inlet spud• Outlet spud with 1-1/2" tubing tailpiece• Wall hanger• Fixture only• Meets ANSI flush requirements at 0.125 to 1.0 gpf

❏ 6581.001EC Top spud with EverClean®

Nominal Dimensions:324 x 324 x 457mm(12-3/4" x 12-3/4" x 18")

Recommended working pressure – between20 psi at valve when flushing and 80 psi static

Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.2/CSA B45.1 for Vitreous China Fixtures

To Be Specified:❏ Color: ❏ White

❏ Flush Valve: 1.0 gpf Flush Valve: Sensor-Operated: ❏ American Standard Selectronic® #6063.101.002

DC Power (Top Spud) ❏ American Standard Selectronic® #6062.101.002

AC Power (Back Spud)

1.0 gpf Flush Valve: Manual-Operated: ❏ American Standard # 6045.101.002

0.5 gpf Flush Valve: Sensor-Operated: ❏ American Standard Selectronic® #6063.051.002



0.5 gpf Flush Valve: Manual-Operated: ❏ American Standard #6045.051.002

0.125 gpf Flush Valve: Sensor-Operated: ❏ American Standard Selectronic® #6063.013.002



0.125 gpf Flush Valve: Manual-Operated: ❏ American Standard #6045.013.002

❏ “P” Trap:


When used with 0.125 gpf

urinal flush vale

When used with 0.125 or 0.5 gpf

urinal flush vale

EVERCLEAN

M150 © 2018 AS America Inc.spec_6581.001 Maybrook EC 11/18

Maybrook® Universal Urinal

VITREOUS CHINA WITH EVERCLEAN®

NOTES:* DIMENSIONS SHOWN FOR LOCATION OF “P” TRAP IS SUGGESTED.“P” TRAP AND FLUSH VALVE NOT INCLUDED AND MUST BE ORDERED SEPARATELY.PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.


292mm(11-1/2") 324mm

(12-3/4")

121mm(4-3/4")

19mm (3/4") N.P.T. OR C.W.T.SUPPLY TO FLUSH VALVE

K-2HANGER

298mm(11-3/4")

457mm(18")

133mm(5-1/4")

10mm (3/8") D. HOLES

171mm(6-3/4")

38mm (1-1/2") O.D. WASTE

38mm (1-1/2") O.D. TAILPIECE

32mm(1-1/4")SUGGESTED*

298mm(11-3/4")

292mm(11-1/2")

324mm(12-3/4")

19mm (3/4") SPUD

64mm(2-1/2")

FINISHED WALL

178mm(7")

610mm (24")

OPTIONALTO FINISHED

FLOOR

6581.001EC TOP SPUD

G2 SENSOR FLUSHOMETERG2 8110

Sloan 10500 Seymour Ave, Franklin Park, IL 60131Phone: 800.982.5839 • Fax: 800.447.8329 • sloan.com

Downloaded 07/26/19 • Revised 05/22/19 • View Latest VersionPage 1 of 1

OPTIONSFinish

Polished Chrome (CP) Brushed Nickel (BN) Brushed Stainless (SF) Polished Brass (PB)

Control Stop Less (L/STOP)

Outlet Tube Trap Primer (TP)

Bumper Angle Stop (YO)

Compliances & Certifications ADA Compliant BAA Compliant UPC Certified UL Certified cUPC Certified

NOTESFor product line drawings, view model-specific spec sheets.

All information contained within this document subject to changewithout notice.

Image for a standard G2 8110 shown

DESCRIPTIONG2 Exposed Sensor Water Closet Flushometer

FEATURESAutomatically operates by means of an infrared sensor withmultiple-focused, lobular sensing fields for high and lowtarget detectionUser-friendly, three-second flush delay and Courtesy Flush®override buttonAdjustable tailpieceHigh copper, low zinc brass castings for dezincificationresistanceAvailable in low consumption (1.6 gpf/6.0 Lpf), water saver(3.5 gpf/13.2 Lpf), and high efficiency (1.28 gpf/4.8 Lpf)modelsValve body, Cover, Tailpiece and Control Stop shall be incompliance with ASTM Alloy Classification for Semi-RedBrassValve shall be in compliance to the applicable sections ofASSE 1037.

DOWNLOADSOptima Plus Valve Installation InstructionsG2 Repair and Maintenance GuideControl Stop Repair and Maintenance GuideFlush Connections Flanges Repair and Maintenance GuideTail Piece Repair and Maintenance GuideSloan Optima Plus Repair and Maintenance GuideAdditional Downloads

https://www.sloan.com/commercial-bathroom-products/flushometers/g2/g2-8110

https://www.sloan.com/sites/default/files/2017-01/0816452Rev5.pdf

https://www.sloan.com/sites/default/files/2018-08/G2%2520and%2520Optima%2520Plus.pdf

https://www.sloan.com/sites/default/files/2018-08/Control_Stop_AllFlushometers.pdf

https://www.sloan.com/sites/default/files/2018-11/flush_connections-flangesAllFlushometers.pdf

https://www.sloan.com/sites/default/files/2018-08/Tail_PieceAllFlushometers.pdf

https://www.sloan.com/sites/default/files/2018-08/Sloan_Optima_Plus_Flushometers.pdf

https://www.sloan.com/commercial-bathroom-products/flushometers/g2/g2-8110

https://www.sloan.com

https://www.sloan.com/general-spec/2346

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 8/10/18S/B Printed in U.S.A.The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2018 by Bobrick Washroom Equipment, Inc.

Technical Data

L

L

Edge ofFlange to Wall

36''915mm

4''100mm

39-3/4''1010mm 57-3/4''

1465mm

50''1270mm



32''815mm

4''100mm

39-3/4''1010mm

27-3/4''705mm

24''610mm


continued . . .

42''1065mm

4''100mm

50''1270mm

57-3/4''1465mm

45-3/4''1160mm



2''50mm

2-1/4''55mm

3-1/8''80mm

5/16''8mm

Snap Flange Cover

3-1/4''85mmDia.

1-1/2''38mm

End Mounting Flange

3-1/8''80mm

Intermediate Flange

2-5/8''65mm

2-1/4''55mm

3-1/8''80mm

1¼" (32mm) DIAMETERSTAINLESS STEEL GRAB BARS

WITH SNAP FLANGEB-5806

SERIES

Satin finish Satin finish with peened gripping surface; add suffix .99 to model number

Specify Finish Required:

HORIZONTAL VERTICAL

B-5806 x 18, 24, 30, 36, 42, 48

TWO-WALLTUB / SHOWER

COMPARTMENT BAR

B-5837

HORIZONTALTUB / SHOWER

COMPARTMENT BAR 24 x 36

B-58616

TWO-WALLTOILET COMPARTMENT BAR 42 x 54

B-5897

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-5806 r8/10/18S/B Printed in U.S.A.The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2018 by Bobrick Washroom Equipment, Inc.

MATERIALS:

Grab Bar — 18-8, Type-304, 18-gauge (1.2mm) stainless steel tubing with satin-finish. 1-1/4" (32mm) outside diameter. Ends are heliarc welded to concealed mounting flanges. Clearance between the grab bar and wall is 1-1/2" (38mm).

Concealed Mounting Flanges — 18-8, Type-304, 11-gauge (3.2mm) thick, stainless steel plate; end flanges 2" x 3-1/8" (50 x 80mm) with holes for attach-ment to wall. Intermediate flanges 2-5/8" x 3-1/8" (65 x 80mm) wide x 3-1/8" (80mm) diameter.

Snap Flange Covers — 18-8, Type-304, 22-gauge (0.8mm) drawn stainless steel with satin-finish. 3-1/4" (85mm) diameter x 5/8" (16mm) deep. Each cover snaps over mounting flange to conceal mounting screws.

STRENGTH:

Bobrick grab bars that provide 1-1/2" (38mm) clearance from wall can support loads in excess of 900 pounds (408kg) if properly installed. Other grab bar configurations can support loads in excess of 250 pounds (113kg) if properly installed, complying with accessible design (including ADAAG in the U.S.A.) for structural strength.

Safety Warning: Grab bars are no stronger than the anchors and walls to which they are attached and, therefore, must be firmly secured in order to support the loads for which they are intended. To avoid potential injury, the building owner or maintenance personnel should remove the grab bar from service if the grab bar is not adequately secured to wall or if there is any observed damage to the welds.

INSTALLATION:

Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten concealed mounting flanges to anchor device or backing with at least two screws opposing each other in each flange. Snap flange covers over each mounting flange to conceal mount-ing screws. Concealed anchor devices and mounting screws are not included with Bobrick grab bars and must be specified as an accessory.

For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting flanges. Place grab bar in desired mounting location. Use intermediate flange as a template to mark location of mounting screws at intermediate flange only. Mark screw locations at the center of the slot in the middle of the double-keyhole shaped mounting holes (2) in the intermediate flange. Remove grab bar from wall. Drive the intermediate flange mounting screws into wall at marked locations. Note: Make sure to leave a space of just over 1/8'' (3.17mm) between the underside of the screw head and the wall. Install grab bar on the wall by placing the round ends of the intermediate flange double-keyhole shaped mounting holes over the mounting screws (2) are located in the middle of the flange slots. Install the mounting screws into the wall at the end flanges and secure tightly. Tighten the mounting screws at the intermediate flange. Press all snap-flange covers into place to conceal mounting flanges.

Note: Recommend use of 1/4'' or #14 sheet metal or wood screws to install Intermediate Flange. #12 screws may also be used.

Important Notes:

1. Mounting Kits — Bobrick offers a mounting kit for installing grab bars; one Bobrick mounting kit is required for each flange.

2. Grab Bar Fastener — Bobrick offers a grab bar fastening system that secures all Bobrick grab bar series; one Bobrick fastener is required for each flange. Install grab bar without backing in wall requires minimum 5/8" (16mm) thick painted or tiled drywall.

3. Optional Anchor Device — Bobrick grab bar anchor device includes stainless steel machine screws to be used for attaching grab bars to anchors. one Bobrick concealed anchor device is required for each flange.

SPECIFICATION:

Grab bar shall be Type-304 stainless steel with satin-finish. Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/4" (32mm) outside diameter. Clearance between the grab bar and wall shall be 1-1/2" (38mm). Concealed mounting flanges shall be 11-gauge (3.2 mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall. Flange covers shall be 22-gauge (0.8mm) stainless steel, 3-1/4" (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws and/or WingIt fasteners. Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit. Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Grab Bar shall be Model __________ (insert model number) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; and Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

Description

Consists of 10–32 x 5/16'' round-head, Phillips 18/8 stainless steel screws. (1) WingIt grab bar fastener.

WingIt™ Fastener No.

251-4

Mounting Kit No.

252-30

Description

Consists of (3) #14 x 2½'' Type-304 stainless steel,Phillips round-head, sheet-metal screws.

Description

Anchor for 3/4" to 1" (19-25mm) panel1 anchor required for each flange.

Anchor for 1/2" to 1" (13mm) panel1 anchor required for each flange.

Optional Anchor No.

2583

2586

Bay West

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 10/18/13 Printed in U.S.A.The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2013 by Bobrick Washroom Equipment, Inc.

Technical Data

Finish Face of Wall

S

1-11/16''45mmTyp.

Rec

om

men

ded

Mo

un

tin

g H

eig

ht

Off

Flo

or

Fo

r U

niv

ersa

l / A

cces

sib

le D

esig

n

30'

' 76

0mm

3-13/16''95mm

7-1/2''190mm

Hinged Lid

1-11/16''45mmTyp.

S

10''255mm

ConturaSeries®

SURFACE-MOUNTEDSANITARY NAPKIN DISPOSAL

MATERIALS:Container — 18-8, type-304, 22-gauge (0.8mm) stainless steel. All-welded construction. Exposed surfaces have satin finish. Integral finger depression for opening cover. Front of container has same degree of arc as front of cover and other Bobrick ConturaSeries washroom accessories. Radius on side edges of container match corners and edges of cover and other ConturaSeries accessories.

Cover — 18-8, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn, one-piece, seamless construction. Front of cover has same degree of arc as front of container and other Bobrick Contura Series washroom accessories. Radius on corners and edges of cover match side edges of container and other Contura Series accessories. Secured to container with a full-length stainless steel piano-hinge.

OPERATION:Cover flips up for disposal of sanitary napkins and for servicing container.

INSTALLATION:For partitions with particle-board or other solid core, secure with two #8 x 3/4'' (4.2 x 19mm) sheet-metal screws (not furnished) at all points indicated by an S, or provide through-bolts, nuts, and washers.

For hollow-core metal partitions, provide solid backing into which sheet-metal screws can be secured. If two units are installed back-to-back, then provide threaded sleeves and machine screws for the full thickness of partition.

For masonry walls, provide fiber plugs or expansion shields for use with sheet-metal screws, or provide 3/16" (5mm) toggle bolts or expansion bolts.

For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with sheet-metal screws.

SPECIFICATION:Surface-mounted sanitary napkin disposal shall be type-304 stainless steel with all-welded construction; exposed surfaces shall have satin finish. Front of sanitary napkin disposal shall have same degree of arc and match other Bobrick ConturaSeries accessories in the washroom. Radius on corners and edges of sanitary napkin disposal shall complement other Bobrick ConturaSeries washroom accessories. Cover shall be drawn, one-piece, seamless construction and secured to container with a full-length stainless steel piano-hinge. Container shall have integral finger depression for opening cover.

Surface-Mounted Sanitary Napkin Disposal shall be Model B-270 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

B-270

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 11/17/15 Printed in U.S.A.The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2015 by Bobrick Washroom Equipment, Inc.

Technical Data

S S

3-1/2''90mm

8-3/4''220mm

15-3/4''400mm

4-1/2''115mm

11''280mm

Finish Face of Wall

2''50mm

Rec

om

men

ded

Mo

un

tin

g H

eig

ht

Off

Flo

or

45''

to 5

9''

114

5 to

150

0mm

Rec

om

men

ded

Mo

un

tin

g H

eig

ht

Off

Flo

or

Fo

r A

cces

sib

le D

esig

n

30''

to 4

8''

760

to

122

0mm

MATERIALS:

18-8, type-304, 22-gauge (0.8mm) stainless steel with satin finish. All-welded construction with beveled opening.

OPERATION:

Dispenses single- or half-fold paper toilet seat covers from beveled opening. Dispenser fills from bottom through concealed opening. Capacity: 250 toilet seat covers or one box.

INSTALLATION:

Mount unit on wall or toilet partition with two flat-head screws, not furnished by manufacturer, at points indicated by an S. For plaster or dry wall construction, provide concealed backing that complies with local building codes, then secure unit with flat-head screws not furnished. For other wall surfaces, provide fiber plugs or expansion shields for use with screws, not furnished, or provide 1/8'' (3mm) toggle bolts or expansion bolts.

Note: Provide a 5'' (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection to provide room for filling dispenser from bottom.

SPECIFICATION:

Surface-mounted toilet-seat-cover dispenser shall be type-304, 22-gauge (0.8mm) stainless steel with all-welded construction; exposed surfaces shall have satin finish. Dispenser shall have a concealed opening in bottom for filling. Capacity shall be 250 paper toilet seat covers or one box.

Surface-Mounted Seat-Cover Dispenser shall be Model B-221 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

ClassicSeries®

SuRFACE-MOuNTEDSEAT-COVER DISPENSER

B-221

M15 © 2016 AS America Inc.spec_9024 Decorum Wall-Hung Lav w/EC Rev. B 6/16

DECORUM®

WALL-HUNG LAVATORY WITH EVERCLEAN®

VITREOUS CHINA

DECORUM® WALL-HUNG LAVATORYWITH EVERCLEAN®

• 20"x18"vitreouschinalavatorywithEverCleanincluded• Availablewithrearoverfloworlessoverflow• Recessedself-drainingdeckwithminimalbacksplash• Forconcealedarmorwallsupport(wallhangerincluded)• ADAandTAScompliant• ShownwithSerinfaucets(soldseparately)• Shownwithdraingrid(soldseparately)

❏ 9024.000ECNofaucetholes❏ 9024.001ECCenterholeonly(CHO)❏ 9024.021ECCHOwithlefthandsoapdispenser❏ 9024.011ECCHOwithrighthandsoapdispenser❏ 9024.901ECCHOlessoverflow❏ 9024.921ECCHOwithlefthandsoapdispenser lessoverflow❏ 9024.911ECCHOwithrighthandsoapdispenser lessoverflow❏ 9024.004EC4"centers❏ 9024.024EC4"centerswithlefthandsoapdispenser❏ 9024.014EC4"centerswithrighthandsoapdispenser❏ 9024.904EC4"centerslessoverflow❏ 9024.924EC4"centerswithlefthandsoapdispenser lessoverflow❏ 9024.914EC4"centerswithrighthandsoapdispenser lessoverflow❏ 9024.008EC8"centers❏ 9024.908EC8"centerslessoverflow

Nominal Dimensions: 464mm(18-1/4")deep,508mm(20")wide

Bowl sizes:354mm(13-15/16")wide,325mm(12-13/16")fronttoback,127mm(5")deep

BARRIER FREE

9024.001ECshownwith2064SeriesSerinFaucet

9024.000ECshownwithR350&T064SeriesSerinFaucet

Compliance Certifications -Meets or Exceeds the Following Specifications:•ASMEA112.19.2forVitreousChinaFixtures

To Be Specified:❏ Color: ❏White ❏ Faucet*:❏ FaucetFinish:❏Supplies:❏ 1-1/4"Trap:❏ SuggestedcarriersincludeJayR.Smith models0801and0700

*Seefaucetsectionforadditionalmodelsavailable

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDE-LINES AND ANSI A117.1 ACCESSIBLE AND USABLEBUILDINGS AND FACILITIES - CHECK LOCAL CODES.Top of front rim mounted 864mm (34") from finished floor.

SEENEXTPAGEFORROUGHING-INDIMENSIONS


DECORUM®


VITREOUS CHINABARRIER FREE

FITTINGCENTERSET

SPREAD

A4" (102 mm)8" (203 mm)

*NOT AVAILABLE ON 8" FAUCET SPREAD MODELS

2-1/4"(57 mm)

18-1/4"(464 mm)

7-1/16"(180 mm)

12-13/16"(325 mm)

A

*4-5/8"(117 mm)

Ø 1-3/8"(Ø 35 mm)

Ø 1-3/8"(Ø 35 mm)

Ø 1"(Ø 25 mm)

16-1/2"(419 mm)

3-1/8"(80 mm)

9-1/16"(230 mm)

15"(380 mm)

13-15/16"(354 mm)

18-1/4"(464 mm)

9"(229 mm)

8" MIN(203 mm)

27" MIN(686 mm)

11" MIN(280 mm)

17" MIN(432 mm)

34" MAX(864 mm)

6" MAX(152 mm)

BARRIER FREECLEARANCE

Ø 1/2"(Ø 13 mm)

Ø 1/2"(Ø 13 mm)

Ø 2-1/8"(Ø 54 mm)

■16-1/2"(419 mm)

■6"(152 mm)

■1-9/16"(40 mm)

■1-13/16"(46 mm)

■16-11/16"(424 mm)

5"(127 mm)

■4-3/16"(106 mm)

SUPPLIES ASREQUIRED

SUPPLIES ASREQUIRED

1-1/4" O.D. WASTE OUTLET FOR POP-UP DRAIN

1-1/4" O.D. WASTEOUTLET FOR

POP-UP DRAIN

8"(203 mm)

11-1/4"(286 mm)

11-3/4"(298 mm)

13-7/8"(352 mm)

20"(508 mm)

NOTES:●LOOSEKEYANGLESTOPS,LESSWALLESCUTCHEONS.SUPPLIESREQUIRED.DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPARESUGGESTED.■SUITABLEFORREINFORCEMENTONLY,ACTUALDIMENSIONSMUSTBETAKENFROMFIXTURE.FITTINGSNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.IMPORTANT:DimensionsoffixturesarenominalandmayvarywithintherangeoftolerancesestablishedbyANSIStandardA112.19.2.Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibilityisassumedforuseofsupersededorvoidedpages.


DECORUM®


VITREOUS CHINABARRIER FREE

Model 9024.000ECNoFaucetHoles

Model 9024.014EC4"CentersWithRightHandSoapDispenser

Model 9024.008EC8"Centers

Model 9024.024EC4"CentersWithLeftHandSoapDispenser

Model 9024.904EC4"CentersLessOverflow

Model 9024.001ECCenterHoleOnly(CHO)

Model 9024.004EC4"Centers

Model 9024.021ECCHOWithLeftHandSoapDispenser

Model 9024.011ECCHOWithRightHandSoapDispenser

Model 9024.901ECCHOLessOverflow

Model 9024.908EC8"CentersLessOverflow

Model 9024.911ECCHOWithRightHandSoapDispenser

LessOverflow

Model 9024.914EC4"CentersWithRightHandSoapDispenser

LessOverflow

Model 9024.921ECCHOWithLeftHandSoapDispenser

LessOverflow

Model 9024.924EC4"CentersWithLeftHandSoapDispenser

LessOverflow

OPTIMA® SENSOR FAUCETETF-80-4-BOX-BDT-CP-0.5GPM-MLM-IR-BT-FCT


Code 3365230BT • Downloaded 08/19/19 • Revised 07/03/19 • View Latest VersionPage 1 of 2

CODE NUMBER3365230BT

DESCRIPTION4" Trim Plate, Box Transformer Power Supply, Below DeckThermostatic Mixing Valve, Polished Chrome Finish, 0.5 gpm, Multi-Laminar Spray, Infrared Sensor, Smart Faucet, Optima® Hardwired-Powered Deck-Mounted Mid Body Faucet.

DETAILSFlow Rate: 0.5 gpm (2 Lpm) (0.5GPM)Spray Type: Multi-Laminar (MLM)Sensor Type: Infrared (IR)Mounting Type: Single HoleTrim Plate: 4" (102mm) (4)Power Supply: Box Transformer (BOX)Temperature Mixer: Below Deck Thermostatic Mixing Valve (BDT)Finish: Polished Chrome (CP)Factory Default Timeout: 30sFactory Default GPC: 0.25

FEATURESCommercial Grade Faucet, ADA Compliant, Cast Brass Spout, QuickConnect Fittings, Integrated Water Shut-off, Wireless SettingsAdjustment, On-demand or Metered activation, Hygienic Line Flush,Water Usage and Battery Strength Reporting, Self-adapting Sensor

ELECTRICAL SPECIFICATIONSBattery Life: 3 years 8,000 cycles/month

Optional power harvesting significantly extends service lifeSelf-Adjustment Range: 0" (0mm)Sensor Range: 0" (0mm)Timeout Adjustment Settings: 30s

POWER SUPPLY OPTIONS6VDC Plug Adapter (included with PLG models)6VDC Ganged Adapter Kit (up to 6 units)(sold separately)24VAC Box Transformer (included with BOX models)

VIDEOS

Optima Faucet App

Sloan Optima Below Deck Faucet

DOWNLOADSOptima Smart Faucet Below Deck Installation InstructionsTrim Plates Repair and Maintenance GuideFaucet Spray Heads Repair and Maintenance GuideETF-80/880 and EBF-85/187 Below Deck Repair and MaintenanceGuideAdditional Downloads

Variation not shown: 4" Trim Plate

COMPLIANCES & CERTIFICATIONS

(ADA Compliant, ASME A112.18.1 Compliant, CalGreenCompliant, CEC Compliant, cUPC Certified, cUPC Low LeadCompliant, GPC 0.25 or less, NYC604.4, Proposition 65, TAS, ULCertified, UPC Certified, UPC Low Lead Compliant)

RECOMMENDED SPECIFICATIONFaucet shall include cast brass body, quick-connect fittings,twist-off/shut-off solenoid assembly, removable batterycartridge, flexible power supply and allow adjustment ofsettings wirelessly via Apple or Android smartphones.

NOTESAll information contained within this document subject tochange without notice.

Looking for other variations of the ETF-80 product? View thegeneral spec sheet with all options.

Find a matching soap dispenser for this faucet.Find a compatible sink for this faucet.

https://vimeo.com/282568434




https://www.sloan.com/sites/default/files/2019-01/0816843Rev1_10-15-18.pdf

https://www.sloan.com/sites/default/files/2018-08/Trim_PlatesAllFaucets.pdf

https://www.sloan.com/sites/default/files/2018-08/Optima-OptimaPlusFaucet_Spray_Heads.pdf

https://www.sloan.com/sites/default/files/2019-02/RM_BT_80-85-880-187_0.pdf

https://www.sloan.com/sites/default/files/2019-02/RM_BT_80-85-880-187_0.pdf

https://www.sloan.com/commercial-bathroom-products/faucets/optima/etf-80




https://www.sloan.com/commercial-bathroom-products/soap-dispensers

https://www.sloan.com/commercial-bathroom-products/sinks


https://www.sloan.com/spec-sheet/3365230BT

OPTIMA® SENSOR FAUCETETF-80-4-BOX-BDT-CP-0.5GPM-MLM-IR-BT-FCT


Code 3365230BT • Downloaded 08/19/19 • Revised 07/03/19 • View Latest VersionPage 2 of 2

WARRANTY3 Year

ROUGH-IN


https://www.sloan.com/spec-sheet/3365230BT

14.39"

5.44"

1.57"

11.78" 9.12"

8"4"

FRONT (in)

SIDE (in)

BACK (in)

TECHNICAL DATA SHEET

Electronic Touchless Roll Towel Dispenser

.28"

See Next Page for mm

Product Code: T8400 T8490

USA

San Jamar555 Koopman LaneElkhorn, Wisconsin 53121USAT:+1.262.723.6133F:[email protected]

San Jamar Canada3300 Bloor Street West Center Tower, 11th FloorSuite 3140 Toronto, ON M8X 2X3CANADAT:+1.416.760.7367F: [email protected]

San Jamar EuropeSchoorstraat 26a, bus 12220 Heist op-den BergBELGIUMT: +32 1522 8140F: +32 1522 [email protected]

San Jamar MéxicoAv. Universidad #1377-701Colonia Axotla CP 01030Del. Alvaro ObregoMEXICO, D.F.T: +52 (55) 3626 0772F: +52 (55) 5273 4495 [email protected]

SIMPLE TO USEConveniently placed keypad for adjustable paper length (8", 12", 16" and delay (0, 11/2, 3 seconds)

UNIVERSALDispenses any paper quality including 100% recycled paper

RELIABLEQuick paper deliveryIndustry leading battery life

COMPACTUp to 25% smaller than other leading electronic dispensers

Installation: Wall mounted

Closure: With lock

Color: Transparent Black Pearl (TBK) Transparent Arctic Blue (TBL)

Dimensions:14.4 in (L) x 11.8 in (W) x 9.1 in (D)

Capacity:(1) 8" wide roll; 8" diameter

Core Diameter: 1.5 in

Case Weight: 4.1 lbs

Materials: Base: break resistant plasticCover: break resistant plastic

Standard Product Codes: T8400TBK/TBL, T8490TBK/TBL

Batteries Required: Uses 4 D-Cell Alkaline Batteries

Features Also Available: (please call customer care) Replaceable CoversReplacement Keys and Lock Fingers2" hub adapters (2) - X100960Mercury Free “Green” D-Cell Batteries (4 pk): XT100886

365.4

138.2

39.8

299.1 231.7

203.2101.6

FRONT (mm)

SIDE (mm)

BACK (mm)

Electronic Touchless Roll Towel Dispenser

7.1

SIMPLE TO USEConveniently placed keypad for adjustable paper length (8", 12", 16" and delay (0, 11/2, 3 seconds)

UNIVERSALDispenses any paper quality including 100% recycled paper

RELIABLEQuick paper deliveryIndustry leading battery life

COMPACTUp to 25% smaller than other leading electronic dispensers

Installation: Wall mounted

Closure: With lock

Color: Transparent Black Pearl (TBK) Transparent Arctic Blue (TBL)

Dimensions:36.5 cm (L) x 29.9 cm (W) x 23.2 cm (D)

Capacity:(1) 20cm wide roll; 20cm diameter

Core Diameter: 3.8cm

Case Weight: 1.9 kgs

Materials: Base: break resistant plasticCover: break resistant plastic

Standard Product Codes: T8400TBK/TBL, T8490TBK/TBL

Batteries Required: Uses 4 D-Cell Alkaline Batteries

Features Also Available: (please call customer care) Replaceable CoversReplacement Keys and Lock Fingers2” hub adapters (2) - X100960Mercury Free “Green” D-Cell Batteries (4 pk): XT100886

Product Code: T8400 T8490

TECHNICAL DATA SHEET

USA

San Jamar555 Koopman LaneElkhorn, Wisconsin 53121USAT:+1.262.723.6133F:[email protected]

San Jamar Canada3300 Bloor Street West Center Tower, 11th FloorSuite 3140 Toronto, ON M8X 2X3CANADAT:+1.416.760.7367F: [email protected]

San Jamar EuropeSchoorstraat 26a, bus 12220 Heist op-den BergBELGIUMT: +32 1522 8140F: +32 1522 [email protected]

San Jamar MéxicoAv. Universidad #1377-701Colonia Axotla CP 01030Del. Alvaro ObregoMEXICO, D.F.T: +52 (55) 3626 0772F: +52 (55) 5273 4495 [email protected]

continued . . .

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 2/1/18 R/B Printed in U.S.A.The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2018 by Bobrick Washroom Equipment, Inc.

Technical Data

MIRROR WITHSTAINLESS STEEL

ANGLE FRAMEAND SHELF

Designer's Notes:1 Special-order sizes available on request.2. Maximum size one-piece angle-frame mirror, 96'' x 72'' (244 x 183cm); minimum size, 12" x 12" (30 x 30cm). 3. All Bobrick framed mirror/shelf models are manufactured to overall width and height dimensions of mirror, not

including shelf. EXAMPLE: For Lock Tab Design B-292 2436 (61 x 95cm) mirror will be furnished 24'' x 37-1/4'' (61 x 94cm) outside-of-frame to outside-of-frame including shelf.

4. To specify special sizes use Series Number followed by width x height in inches. EXAMPLE: B-292 2024 20" x 24" (51 x. 61cm).

5. Bobrick framed mirror/shelf models are manufactured to a tolerance ± 1/8'' (3.2mm).6. For sufficient space to lift mirror onto wall hanger(s), provide 1" (25mm) minimum clearance above top of mirror frame.7. Provide 1'' (25mm) minimum clearance at bottom of mirror for unlocking mirror from wall and 1/2'' (12.7mm) clearance on each side.

Figure: 1

B-292SERIES

Snap Locking Design(Rear View)

Lock Tab Design(Rear View)

Figure: 2

Note: Mirrors greater than 30" in width will have multiple hanger bracket pockets with a typical 8" off each edge.

All Other Size Mirrors

MODELNO.

STANDARD B-292 SERIES MIRRORS

OVERALL SIZEW H

B-292 1836 18'' (46cm) 36'' (91cm)

3/4''19mm

5''127mm

3/4''19mm

2-1/2''65mm

S

2-9/16''65mm

S

4'' or 5" Typ.100 or 125mm

S

Side ViewBack Plate/Wall Hanger

Frame

Mirror

Finish Face of Wall

Slide flat-blade screwdriver or Key between Mirror andWall. Depress Tab on backPanel and remove Mirror. Contact factory for key.

Lock Tab

4-5/8"117mm

3-1/8"79mm

WallBracket

LockTab

MirrorKey

HalfMirror Width

3/4''19mm

Frame

Mirror

5-3/4''146mm

1-1/4''32mm

S

S

1/2''13mm

Finish Face of Wall

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-292 Rev. 2/01/18 R/B Printed in U.S.A.The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2018 by Bobrick Washroom Equipment, Inc.

MATERIALS:Frame — 18-8, Type-304, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with satin finish. One-piece, roll-formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame tightly against mirror. Corners of mirror frame are heliarc welded, ground, and polished smooth. Galvanized steel back is fastened to frame with concealed screws and equipped with integral horizontal hanging brackets near the top for hanging the mirror and near the bottom to prevent the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger.

Shelf — 18-8, Type-304, 18-gauge (1.2mm) stainless steel with satin finish, 3/4" (19mm) return edge on front. Front and side return edges hemmed for additional strength and safety. Front corners of shelf are welded, ground, and polished smooth. Shelf is welded to mirror frame. No exposed rivet-heads, screws, or fasteners of any type on frame or shelf.

Mirror — No. 1 quality, 1/4" (6mm) select float glass (standard glass): selected for silvering, electrolytically copper-plated by the galvanic process, and guaranteed for 15 years against silver spoilage. All edges protected by plastic filler strips; back is protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding.

Concealed Wall Hanger — 16 gauge cold roll steel construction. Incorporates upper and lower support members, which engage backplate louvers to keep mirror against wall.

INSTALLATION:Mount wall hanger on wall with screws (not furnished) at points indicated by an S. For plaster or dry wall construction, provide backing to comply with local building codes, then secure wall hanger with screws (not furnished). When providing a concealed backing, allow backing to cover minimum range of mounting hole locations shown on drawing. For other wall surfaces, provide fiber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or expansion bolts. Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members. To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1" (25mm) above final position and then lowered into final position.

Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position (see figure 3). Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror near the bottom or under the bottom of the mirror and pulling mirror bottom forward and then up.Lock Tab Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position (see figure 4). Locking device may be unlocked by sliding a flat-blade screwdriver or Key between mirror and wall at center of mirror and depressing tab on back panel. If key is required, please contact the factory.

SPECIFICATION:Mirror shall have a one-piece, Type-304 stainless steel angle frame, 3/4" x 3/4" (19 x 19mm) with continuous integral stiffener on all sides and beveled front to hold frame tightly against mirror; corners shall be heliarc welded, ground, and polished smooth; all exposed surfaces shall have satin finish. Shelf shall be Type-304, 18-gauge (0.8mm) stainless steel with satin finish. Shelf shall have a 3/4" (19mm) return edge on front. Front and side return edges hemmed and corners welded, ground, and polished smooth. Shelf shall be welded to mirror frame. No rivet-heads, screws, or fasteners of any type shall be exposed on frame or shelf. Select float glass mirror shall be guaranteed for 15 years against silver spoilage. All edges shall be protected by plastic filler strips and the back shall be protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding. Galvanized steel back shall have integral horizontal hanging brackets located at top and bottom for mounting on concealed wall hanger and to prevent the bottom of the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger. Mirror shall be removable from wall hanger for reglazing mirror.

Framed Mirror With Shelf shall be Model B-292 _______________ (insert width and height) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

Figure: 3 Figure: 4

Snap Locking Design(Front View)

Lock Tab Design - Up to 30" Width(Front View)

Aprox. 1"25mm Initial

Position

S

S

FinalPosition

CLAprox. 1"

25mm InitialPosition

S

S

FinalPosition

CL

Metalux

WNLEDLED

Uti l i ty LED Wraparound

SPECIFICATION FEATURES

ConstructionHousing consists of die formed cold rolled steel. Ends formed with the housing for strength and provisions for continuous row aligners. Steel end plates with 7/8” KO and light-seal embossment. Driver cover can be removed by taking out four pan screws.

ControlsWNLED is Powered by Fifth Light, with standard a 0-10V continuous dimming driver that works with any 0-10V control/ dimmer. Combine with energy saving products like occupancy sensors, daylighting controls and lighting relay panels to maximize energy savings. Dimming range is 10% to 100%; varies by control device.

ElectricalLong-Life LED system coupled with electrical driver to deliver optimal performance. LED’s available in 3000K, 3500K, 4000K and 5000K with a typical CRI 85. Projected life is 60,000 hours at 70% lumen output. UL listed. Electronic drivers are available for 120-277V applications. A 0-10V dimming driver is standard.

FinishMultistage iron phosphate pretreatment ensures maximum bonding and rust inhibitor. High reflective paint after fabrication, baked white enamel finish is standard.

Channel/Wireway CoverDie formed heavy gauge steel. Tight fit for ease of maintenance.

ShieldingAcrylic, high performance, frost blend. Sides have inside linear prisms and bottom has pyramidal prisms for low brightness control.

Instal lationFixture may be surface, pendant, or stem mounted. See accessories below for ordering information.

ComplianceModules are UL recognized components and indoor luminaires are cULus listed for 25ºC ambient environments, damp location listed, RoHS compliant, and LED modules comply with IESNA LM-79 and LM-80 standards.

Our updated WNLED series is a versatile utility based, traditionally styled LED wraparound series which can be used in a broad range of commercial, schools, institutional, retail and residential applications. This high quality luminaire series utilizes the latest solid state LED lighting and advanced electronic driver technology which provides optimal lighting performance and maximizing energy savings. WNLED is designed to provide long service life eliminating re-lamping issues and minimizing maintenance common with traditional fluorescent.

DESCRIPTIONCatalog # Type

Date

Project

Comments

Prepared by

PS519062EN2016-04-12 09:35:15

1-13/16"[46mm]

19" [483mm]20-5/8" [523mm]

1-1/8"[29mm]

24" [610mm]

8-3/16" [208mm]

1"[25mm]1" [25mm]

6"[152mm]

7-5/8"[194mm]

2'

1-1/8"[29mm]

42-15/16" [1090mm]44-1/2" [1131mm]1-13/16"

[46mm]

7/8" [22mm] K.O. (5)

Ground Screw BumpCeiling Stand-OffEmbossments

48" [1219mm]

42-7/16" [1078mm]

40-7/16" [1027mm]

3"[76mm]

4-1/2"[114mm]

6"[152mm]

7-5/8"[194mm]

4'

MOUNTING DATA

Length Lumens Wattage

2 ft. 2800 28

4 ft. 3200 28

4 ft. 4000 36

4 ft. 5000 47

WATTAGE

Stock*/ MTO**

Lumen Type

Length Catalog NumberNomial Lumens

Wattage lm/W

MTO Standard 2 ft. 2WNLED-LD4-28SL-F-UNV-L8XX-CD1-U 2786 28 101

MTO Standard 4 ft. 4WNLED-LD4-32SL-F-UNV-L8XX-CD1-U 3298 28 118

Stock Standard 4 ft. 4WNLED-LD4-40SL-F-UNV-L8XX-CD1-U 4062 36 113

Stock Standard 4 ft. 4WNLED-LD4-50SL-F-UNV-L8XX-CD1-U 4966 47 107

* Stocked in 3500K and 4000K** Also available in 3000k, 5000K

ENERGY AND PERFORMANCE DATA BY CATALOG NUMBER

Specifications and dimensions subject to change without notice.

Eaton 1121 Highway 74 SouthPeachtree City, GA 30269P: 770-486-4800www.eaton.com/lighting

WNLED

Catalog No. Wt.

2WNLED 5 lbs.

4WNLED 9 lbs.

SHIPPING DATA

AmbientTemperature

TM-21 LumenMaintenance

(12,000 hours)

TheoreticalL70

(Hours)

25°C 80.7% 85,000

Max Ambient temp in compliance with UL: 40°C

LUMEN MAINTENANCE

SeriesWNLED=Utility LEDWraparound

S A M P L E N U M B E R : 4 W N L E D - L D 4 - 4 0 S L - F - U N V - L 8 4 0 - C D 1 - U

PackagingU=Unit Pack

Lamp TypeLD4=LED 4.0

LED Lumens Output28SL=2800 (1)

32SL=320040SL=400050SL=5000

Voltage347=347V (2)

480=480V (2)

UNV=UniversalVoltage 120-277

Number of Drivers1=1 Driver

LensF=Frost Acrylic (standard)

Length2=2 ft.4=4 ft.

A C C E S S O R I E SSCF=Fixed Stem Set (Specify Length)SCS=Swivel Stem Set (Specify Length)SCA=Adjustable 48" Stem SetA1B/Spacer-U=Spacer 1-1/2" to 2-1/2" from ceiling(Use 2 per fixture)

NOTES: (1) 2 ft. model. (2) 4 ft. model only. Specifications & dimensions subject to change without notice. Consult your Eaton Representative for availability and ordering information.

CCTL830=3000KL835=3500KL840=4000KL850=5000K

Driver TypeCD=0-10V Dimming Driver (10% - 100% Dimming)

ORDERING INFORMATION

4WNLED-LD4-32SL-F-UNV-L835-CD1-U

Electronic Driver

Linear LED 3500K

Spacing criterion: (II) 1.2 x mountingheight, (⊥) 1.2 x mounting height

Lumens: 3298

Input Watts: 28.0W

Efficacy: 117.8 lm/W

Test Report: 4WNLED-LD4-32SL-F-UNV-L835-CD1-U.IES

051015202530354045505560657075808590

C a n d l e p owe r

Angle Along II 45° Across ⊥

1124 1124 11241124 1120 11161103 1102 11001069 1071 10711023 1029 1031966 975 978899 913 918826 845 853747 771 781669 695 707586 615 631504 535 554422 455 476342 377 400265 302 327190 231 257121 164 19056 100 1250 44 70

C o e ffi c i e n t s o f U t i l i z a t i o n

Effective floor cavity refl ectance 20%

rc 80% 70% 50% 30% 10% 0%rw 70 50 30 10 70 50 30 10 50 30 10 50 30 10 50 30 10 0

RCR0123456789

10

118 118 118 118 114 114 114 114 108 108 108 102 102 102 97 97 97 94107 102 97 93 103 99 95 91 94 90 87 89 86 84 84 82 80 7897 89 82 76 94 86 80 74 82 76 72 78 73 69 74 70 67 6488 78 69 63 85 76 68 62 72 65 60 68 63 58 65 60 57 5481 69 60 53 78 67 59 53 64 57 51 61 55 50 58 53 49 4674 62 52 46 72 60 52 45 57 50 44 55 48 43 52 47 42 4069 55 46 40 66 54 46 40 52 44 39 50 43 38 47 42 37 3564 50 41 35 62 49 41 35 47 40 34 45 39 34 43 38 33 3159 46 37 32 57 45 37 31 43 36 31 41 35 30 40 34 30 2855 42 34 28 54 41 33 28 40 33 28 38 32 27 37 31 27 2552 39 31 26 50 38 31 26 37 30 25 35 29 25 34 29 24 23

Z o n a l L u m e n S u m m a r y

Zone Lumens % Fixture0-30

0-40

0-60

0-90

0-180

855 25.9

1381 41.9

2390 72.5

3109 94.3

3298 100.0

400

0˚ 15˚ 30˚

45˚

60˚

75˚

90˚

800

1200

PHOTOMETRICS

PS519062EN2016-04-12 09:35:15

4WNLED-LD4-40SL-F-UNV-L835-CD1-U

Electronic Driver

Linear LED 3500K

Spacing criterion: (II) 1.2 x mounting height, (⊥) 1.2 x mounting height

Lumens: 4062

Input Watts: 36.0W

Effi cacy: 112.8 lm/W

Test Report: 4WNLED-LD4-40SL-F-UNV-L835-CD1-U.IES

051015202530354045505560657075808590

C a n d l e p owe r

Angle Along II 45° Across ⊥

1386 1386 13861385 1380 13751360 1357 13541318 1320 13201261 1266 12681190 1201 12031109 1125 11281018 1042 1048922 951 964823 857 868721 759 773620 660 678521 561 584421 464 492326 372 403234 285 317148 201 23370 123 1541 57 89

C o e ffi c i e n t s o f U t i l i z a t i o n

Effective fl oor cavity refl ectance 20%

rc 80% 70% 50% 30% 10% 0%rw 70 50 30 10 70 50 30 10 50 30 10 50 30 10 50 30 10 0

RCR0123456789

10

118 118 118 118 114 114 114 114 108 108 108 102 102 102 97 97 97 94107 102 97 93 103 99 95 91 94 90 87 89 86 84 84 82 80 7897 89 82 76 94 86 80 74 82 76 72 78 73 69 74 70 67 6488 78 69 63 85 76 68 62 72 65 60 68 63 58 65 61 57 5481 69 60 53 78 67 59 53 64 57 51 61 55 50 58 53 49 4674 62 52 46 72 60 52 45 57 50 44 55 48 43 52 47 42 4069 55 46 40 66 54 46 40 52 44 39 50 43 38 47 42 37 3564 50 41 35 62 49 41 35 47 40 34 45 39 34 43 38 33 3159 46 37 32 57 45 37 31 43 36 31 41 35 30 40 34 30 2855 42 34 28 54 41 33 28 40 33 28 38 32 27 37 31 27 2552 39 31 26 50 38 31 26 37 30 25 35 29 25 34 29 24 23

Z o n a l L u m e n S u m m a r y

Zone Lumens % Fixture0-30

0-40

0-60

0-90

0-180

1054 25.9

1702 41.9

2945 72.5

3832 94.3

4062 100.0

500

0˚ 15˚ 30˚

45˚

60˚

75˚

90˚

1000

1500

toilet partition catalog - sccoe

Documents