T H E L E A D I N G E D G E

®

TTTT HHHH EEEE LLL EEEEE AAAA DDDD III NNNNN GGGG EEEE DDDD GGGG EEE

®®®

The Premier UPVC edge trim for flat roofs

Your local Permaroof®trim stockist is:

T H E L E A D I N G E D G E

®

If you require any further product or stockist information please contact us at:Tel: 0800 161 3722 • Email: sales@permaroof.co.uk • Web: www.permaroof.co.uk

Perm

aroo

f®tri

m

Installation of theFascia Kerb Edges (Q1)

Measure length of trim needed, and cut to size. The recommended fixings are 30mm stainless steelMeasure length of trim needed, and cut to size. The recommended fixings are 30mm stainless steel

polytop pins. The fixings should be placed in the pre-cut slots in the vertical face of the Permaroofpolytop pins. The fixings should be placed in the pre-cut slots in the vertical face of the Permaroof®®trim.trim.

(Fig 5) (Fig 5) Place a beadPlace a bead

of Bond n seal sealantof Bond n seal sealant

on the underside ofon the underside of

the trim this gives thethe trim this gives the

trim a watertight seal.trim a watertight seal.

Finish with a bead ofFinish with a bead of

Bond n Seal asBond n Seal as

illustrated illustrated (Fig 6) (Fig 6)

Alternatively, onAlternatively, on

uneven surfaces useuneven surfaces use

the self-adhesivethe self-adhesive

closed cell foam tapeclosed cell foam tape

to provide the sealto provide the seal

(Fig 7). (Fig 7).

Once fixed, place aOnce fixed, place a

joint clip Q8 over thejoint clip Q8 over the

joint as shown……joint as shown……

hook under thehook under the

bottom of the trimbottom of the trim

first… then clip overfirst… then clip over

into placeinto place. .

The foam tape needs to be compressed 30% for a watertight seal. The foam tape needs to be compressed 30% for a watertight seal.

(Fig 8)(Fig 8) Once sealant or foam tape is applied, offer the trim into place and fix securely with 30mm poly-Once sealant or foam tape is applied, offer the trim into place and fix securely with 30mm poly-

pins through slots in vertical face.pins through slots in vertical face.

Corner pieces are dealt with quickly. Apply a small amount of Permaroof trim Bond n Seal sealant Corner pieces are dealt with quickly. Apply a small amount of Permaroof trim Bond n Seal sealant

on the inside of the corner Q4, and offer into place. If poly- pins are used for fixing corners it ison the inside of the corner Q4, and offer into place. If poly- pins are used for fixing corners it is

recommended that a pilot hole is drilled to prevent pins bending.recommended that a pilot hole is drilled to prevent pins bending.

When joining lengths of PermaroofWhen joining lengths of Permaroof®®trim Q1, cap the ends off by applying Bond n Seal sealant to thetrim Q1, cap the ends off by applying Bond n Seal sealant to the

trim profile end caps Q7. Attach the trim as already described, butting the two lengths together, with trim profile end caps Q7. Attach the trim as already described, butting the two lengths together, with

a bead of Bond n Seal Sealant in between.a bead of Bond n Seal Sealant in between.

32227 Permaroof Quicktrim broch.qxd:32227 Permaroof Quicktrim broch 26/4/10 11:20 Page 1

®®®

IntroductionThe Permaroof®trim System has been designed especially for single-ply flat roof

membranes to compliment UPVC fascias and guttering fixed on domestic properties.

It is the finished edge which is seen from ground level so its important it looks neat

and blends with the existing roofline.

It has also been designed with the installer in mind, all the component parts are

fitted with ease and with the option of using longer lengths and fewer joints, so

fitting time is reduced considerably.

Manufacturing Process

Both the fascia edge and gutter edge are extruded

using virgin plastic ensuring colour fast, non brittle,

identical profiles.

Corner pieces and blank ends are injection

moulded using state of the art manufacturing

technology.

The manufacturing process is BSI quality assured

accredited to 99.9% accuracy.

Unique DesignA built in watercheck kerb on the fascia edge trim

assures the rain water is diverted towards the

gutter edge.

The specially formulated Permaroof®trim ‘Bond

and Seal’ sealant or a closed cell form tape is used

between trim and membrane to provide a seal and

polytop pins are used to mechanically fix from the

outside vertical edge ensuring the membrane is

not penetrated.

Along the gutter edge the membrane is

sandwiched between a pre-installed backplate and

a front cover clip ensuring a 100% water tight seal

with no penetrations.

Permaroof®trimThe components

Permaroof®trim Edge/Curb Profile (Q1)

Available in 2.5 meter and 3.5 meter lengths. Longer lengths can be customAvailable in 2.5 meter and 3.5 meter lengths. Longer lengths can be customextruded up to 6 meters. Colours available are black and white. Its uniqueextruded up to 6 meters. Colours available are black and white. Its uniquedesign ensures water is directed to the gutter edge.

Two Part Gutter Edge Trim (Q2, Q3)

A unique and patented design. Used along the gutter edge. It ‘sandwiches’ theroofing membrane eliminating penetration when fixing. Available in black orwhite, It is a 2-part trim sold together and comes in 2.5 meter lengths.

External Corners (Q4)

Injection moulded to the highest of standards. Available in black or white. Canbe installed with the special Permaroof®trim ‘Bond & Seal’ or with polytop pins.trim ‘Bond & Seal’ or with polytop pins.Provides a very neat, professional touch.

Internal Corners (Q5)

Injection moulded to the highest of standards. Available in black or white.

Again installed with the Permaroof®trim ‘Bond & Seal’.

End Caps (Q6, Q7)

The end caps are used for capping off the ends of the trim where they joineach other or about an upstand. Also used for blanking off external corners(Q7) when it meets the gutter edge. (Please refer to fitting guide). Available inblack or white and in 2 sizes.

Joint Clips (Q8)

The joint clips are used for joining two pieces of Edge/Curb trim (Q1) together.40mm wide.

Permaroof®trim ‘Bond & Seal’

A specially formulated sealant designed for maximum adhesion to single plymembranes. Available in black, white or translucent.

Permaroof®trim Closed- Cell Foam Tape

Self adhesive tape applied to base of edge trim QI to give watertight seal onuneven surfaces.

Permaroof®trim is designed for use around the perimeter edge of a flat roof. The edgetrim Q1 is designed with its own water-check kerb. On new builds, the roof should be

constructed without any upstands such as an arris-rail or fillet along the edges. Onrefurbs if fillets are already in situ, ie; on felt roofs, these should be removed to leave a

square edge with the decking boards flush with the fascia (Fig 1).

Installation SequenceImportant! When gluing the membrane to the deck, apply adhesive up to the lower edge of the hook of the topImportant! When gluing the membrane to the deck, apply adhesive up to the lower edge of the hook of the topsection of the back plate Q2, letting 50mm hang loose over the edge. This will allow the drip plate section Q3 tosection of the back plate Q2, letting 50mm hang loose over the edge. This will allow the drip plate section Q3 tobe installed correctly. be installed correctly.

Install gutter edge backplate Q2 before membrane isInstall gutter edge backplate Q2 before membrane is

adhered to deck. adhered to deck. (Fig 1)(Fig 1) Make sure top of backplateMake sure top of backplate

Q2 is flush with surface of roof.Q2 is flush with surface of roof.

Fig 1Fig 1 (Gutter removed for ease of fixing)(Gutter removed for ease of fixing)

(Fig 2)(Fig 2) The gutter edge is finished by “sandwiching”The gutter edge is finished by “sandwiching”

the 50mm excess membrane between the drip platethe 50mm excess membrane between the drip plate

Q3 and the backplate Q2 . The top edge of the dripQ3 and the backplate Q2 . The top edge of the drip

plate Q3 is pushed under the hook of the backplateplate Q3 is pushed under the hook of the backplate

Q2, with the membrane in between the two, thenQ2, with the membrane in between the two, then

clipped into place…clipped into place…

(Fig 3)(Fig 3) The profile of the PermaroofThe profile of the Permaroof®®trim gutter edgetrim gutter edge

illustrating the membrane secured between theillustrating the membrane secured between the

hollow section backplate Q2 and drip plate Q3.hollow section backplate Q2 and drip plate Q3.

((IMPORTANT:IMPORTANT: When joining 2 sections of drip plateWhen joining 2 sections of drip plate

Q3Q3 leave a 3mm gap between joint and use Bond nleave a 3mm gap between joint and use Bond n

seal sealant to fill, this will allow for expansion).seal sealant to fill, this will allow for expansion).

Fig 4Fig 4 (The finished gutter edge)(The finished gutter edge)

(The gutter itself can now be refitted)(The gutter itself can now be refitted)

Perm

aroo

f®tri

m

32227 Permaroof Quicktrim broch.qxd:32227 Permaroof Quicktrim broch 26/4/10 11:21 Page 4