8/10/2019 trimo 2

1/4

Fireproof ROOF Panels Trimoterm SNVTechnical Information

8/10/2019 trimo 2

2/4

Fireproof ROOF Panels Trimoterm SNV

Technical Data

The outstanding technical properties of Trimoterm SNV fireproof roof panels are the

result of careful material selection and modern production processes.

* Required control of distances between supports relating to the static system and loading.

Loading by snow (kN/m2)

Distance(m)

Structural Design Data

Trimo standards consider the most typical case studies of snow loading in accordance with

general sales licence Z-10.4-240 when calculating maximum structural span.

Technical data SNV SNV 60 SNV 80 SNV 100 SNV 120 SNV 150 SNV 200

Panel thickness [mm] 60 80 100 120 150 200

Weight SNV [kg/m2] Fe 0.6 / Fe 0.6 18.9 21.3 23.7 26.1 29.7 35.7

U Thermal conductivity [W/m2K](acc to DIN 52611 and DIN 4108)

0.61 0.48 0.40 0.34 0.27 0.21

Fire resistance class REI(acc to EN 1365-2)*

REI 60 REI 120 REI 150

Combustibility of insulant core(acc to EN 13501-1)

Non - combustible, class A1

Rw Sound reduction [dB]Fe 0.6 / Fe 0.6 30

Min. roof slope 5 or 3 with additional sealing

Cover width [mm] 1000

Panel lenght [m] from 2 to 14

Load-bearing capacity curves have been calculated using the software Sand Stat 3 for multi-span structure of standard panel SNVs,closed building and normal internal temperature. Fixing and required width of supports should be determined for each individual

project by Trimo Technical Support.

8/10/2019 trimo 2

3/4

Loading by snow (kN/m2)

Distance(m)

Sound Insulation

Sound insulation has been measured on a Trimoterm SNV 100 roof panel - Report No. P 1489/

97-510-1, ZAG Ljubljana.

Certificates

Frequency f (Hz)

SoundinsulationR`(dB)

Standardcurve

Cert. No. 650a to LPS 1208

8/10/2019 trimo 2

4/4

Coatings

Steel sheet is preliminary hot galvanised and colour pre-coated. Thickness of a zinc layer is

275 g (Zn)/m2(DIN EN 10142, DIN EN 10147) while colour coating is performed by Coil Coating

procedure. This denotes painting between cylinders and drying in a furnace at a temperature

of minimum 200C.

Basic properties SP PVDF

Class of anticorrosive protection according to DIN 55928/1 III III

Marking of anticorrosive system according to DIN 55928/8 3-160.2 3-600.1

Temperature resistance (C) up to +80 up to +110

Thickness of a a layer (my) 25 25

External climate

Normal

Urban and industrial

Harsh industrial -

Maritime climate1 to 10 km from the coast -

< 1 km from the coast -

Conditions of

buildings interiors

t 25C , 80 %

t 25C , > 80 %

t 50C , > 80 % -

Without heating

Suitable without

reservations

Very suitable

Suitable

- Unsuitable

Two types of metal sheet coatings are used:

- Protection based on polyester marked as SP - standard protection.

- Protection based on polyvinyl idenfluoride marked as PVDF - available on request.

All rights to alternations reserved. The last version of the document can be found on www.trimo.si. Publishedby:TRIMOd.d.,

Design:MetaGabrijel,

Photography:JanezErjavec,Printedby:TiskarnaPetri,Circulation:6000/ANG,12/2004