trufast catalog 2015 - connective...

TRUFAST CATALOG 2015

www.connective-systems.comDenver: (303) 447-0295 | Nothern Colorado: (970) 663-0304 | Toll Free: (800) 638-9264

Version 1 | Release 1.1

2 Confidentiality Statement | Non-Disclosure Statement

This document contains information which is considered to be CONFIDENTIAL and priviledged. If you are not the intended recipient or the person responsible fo delivering this document to the intended recipient, please notify the sender immediately by email ([email protected]), or by phone (970.310.7385), dispose of this document and destroy any copies.

You are hereby notified that any disclosure to unauthorized agents (including, but not limited to industry competitors), retransmission, any form of reproduction, dessimination, copying, modification, distribution or publication of this document or any of its contents is strictly prohibited and may be considered unlawful.

3Table of Contents

Confidentiality Notice

Non-Disclosure Statement

TrufastConfidentiality Statement | Non-Disclosure Statement | 2

Table of Contents | 3

Trufast Catalog | 4

Trufast Catalog | 5

Trufast Catalog: TOC | 6

Trufast Catalog: Roofing Fasteners | 7






Trufast Catalog: Stress Plates and Batten Bar | 13

Trufast Catalog: Termination Bar & Nailins | 14

Trufast Catalog: SIP Fasteners | 15

Trufast Catalog: SIP Fasteners | 16

Trufast Catalog: Tools | 17

Trufast Catalog: Drill and Driver Bits | 18

Trufast Catalog: Base Sheet Fasteners & Accessories | 19

Trufast Catalog: Base Sheet Fasteners & Accessories | 20

Trufast Catalog: Adhesives & Sealants | 21



Trufast Catalog: Adhesives & Sealants & Accessories | 24

Trufast Catalog: Adhesives & Sealants & Accessories | 25

Trufast Catalog: Rooftop Drains | 26

Trufast Catalog: Rooftop Drains | 27

Trufast Catalog: Caddy® Rooftop Suppors | 28

Trufast Catalog: Notes | 29

Trufast Catalog: Committment | 30

Trufast Catalog: Back Page | 31

Caddy Pyramid: Rooftop Support System | 32
















Dow® Tile Bond™ Roof Tile Adhesive | 48

Dow® Tile Bond™ Roof Tile Adhesive | 49

Firestone: I.S.O. Twin Pack™ Insulation Adhesive | 50

Firestone: I.S.O. Twin Pack™ Insulation Adhesive | 51

Fomo Products: Handi Foam Spray Foam | 52

Fomo Products: Handi Foam Spray Foam | 53

Notes | 54

Notes | 55

4 Trufast Catalog

Price Book

Featuring 100% American-made fastening solutions engineered for commercial roofing and structural building applications.

EFFECTIVE 1.1.14

CONNECTIVE SYSTEMS

5Trufast Catalog

For nearly 30 years, Trufast has provided trusted fastening solutions for the commercial roofing industry.

Along the way, we’ve built solid relationships with the finest distributors, systems manufacturers, and

contractors across the country. Today, Trufast is backed by the engineering expertise and financial strength

of AlTenloh, Brinck & co., a global leader in fastening solutions. As we look to the future, you can count

on us to “stay tru” to the strengths that have brought us this far: American manufacturing, unparalleled

service, and our connections with you.

6 Trufast Catalog: TOC

TABLE OF CONTENTS

PAGE

Roofing Fasteners#12 DP Drill Point Roofing Fasteners, Phillips Truss Head 2#12 DPH Drill Point Roofing Fasteners, Hex Head 2#12 PA and PAH Pre-Assembled Screws & Plates 2#14 HD Drill Point Roofing Fasteners, Phillips Truss Head 3#14 HD-SS Stainless Steel Drill Point Roofing Fasteners, Phillips Truss Head 3#15 EHD Drill Point Roofing Fasteners, Phillips Truss Head 4PFC Purlin Fastener 41/4" Concrete Spike 5Fluted Nail Concrete Fastener 5TL Lightweight Fasteners & Plates 6100 Count Packages -- Roofing Fasteners and Plates 7

Stress Plates 8

Batten Bar 8

Termination Bar & Nailins 9

SIP FastenersSIPTP Thread Point Fasteners 10SIPLD Light-duty Drill Point Fasteners 11SIPHD Heavy-duty Drill Point Fasteners 11

Tools 12

Drill & Driver Bits 13

Base Sheet Fasteners and Accessories 14-15

Adhesive & SealantsDow INSTA STIK® Quik Set Roofing Adhesive 16Dow FROTH-PAK Spray Polyurethane Sealant 17Dow TILE BOND 18

ADCO Millennium Adhesive 19

ADCO Millennium Adhesive PG-1 20

Rooftop AccessoriesTrufast Rooftop Drains 21-22 Caddy® Pyramid Rooftop Supports 23-24

Standard Freight & Order Policies 25

Effective 1.1.14 1 CONNECTIVE SYSTEMS

7Trufast Catalog: Roofing Fasteners

ROOFING FASTENERSTRUFAST® #12 DP and DPH Fasteners are designed for insulation attachment to 16 - 22 gauge steel roof decks.They are the only #12 drill point roofing fasteners on the FUTUREMARKET that will drill a 16 gauge deck! Allow for a minimum of 3/4" penetration through the underside of the deck. Both are FM and Miami-Dade Approved.

DP #12 Drill Point, #3 Phillips Truss Head, Black E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-5/8" DP-1625 same 1000 / Bucket 12.5 lbs. 33.45$ 33.45$2-1/4" DP-2250 same 1000 / Bucket 16.2 lbs. 38.75$ 38.75$2-7/8" DP-2875 same 1000 / Bucket 19.7 lbs. 43.95$ 43.95$3-1/4" DP-3250 same 1000 / Bucket 21.5 lbs. 54.40$ 54.40$3-3/4" DP-3750 same 1000 / Bucket 24.6 lbs. 59.25$ 59.25$4-1/2" DP-4500 same 1000 / Bucket 29.2 lbs. 78.70$ 78.70$

5" DP-5000 same 1000 / Bucket 31.8 lbs. 88.90$ 88.90$6" DP-6000 same 1000 / Bucket 38.0 lbs. 124.35$ 124.35$7" DP-7000 same 500 / Bucket 22.1 lbs. 170.65$ 85.33$8" DP-8000 same 500 / Bucket 25.2 lbs. 190.25$ 95.13$

One (1) #3 Phillips Bit TD-30 included per pkg.

DPH #12 Drill Point, 1/4" Hex Head, Black E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-5/8" DPH-1625 same 1000 / Bucket 12.5 lbs. 33.45$ 33.45$2-1/4" DPH-2250 same 1000 / Bucket 16.2 lbs. 38.75$ 38.75$2-7/8" DPH-2875 same 1000 / Bucket 19.7 lbs. 43.95$ 43.95$3-1/4" DPH-3250 same 1000 / Bucket 21.5 lbs. 54.40$ 54.40$3-3/4" DPH-3750 same 1000 / Bucket 24.6 lbs. 59.25$ 59.25$4-1/2" DPH-4500 same 1000 / Bucket 29.2 lbs. 78.70$ 78.70$

5" DPH-5000 same 1000 / Bucket 31.8 lbs. 88.90$ 88.90$6" DPH-6000 same 1000 / Bucket 38.0 lbs. 124.35$ 124.35$7" DPH-7000 same 500 / Bucket 22.1 lbs. 170.65$ 85.33$8" DPH-8000 same 500 / Bucket 25.2 lbs. 190.25$ 95.13$

One (1) 1/4" Hex Driver Bit HH-250-N included per pkg.

PA & PAH Pre-Assembled Screws & Plates#12 DP #3 Phillips Truss Head and DPH 1/4" Hex Head Drill Point Fasteners with 3" Recessed Plate

Length Hex Head Part# New Part No. Phil Hd Part# Pkg Qty/Type Price/1000 Price/Pkg1-5/8" PAH-1625 same PA-1625 250 / Carton 130.35$ 32.59$2-1/4" PAH-2250 same PA-2250 250 / Carton 137.25$ 34.31$2-7/8" PAH-2875 same PA-2875 250 / Carton 144.05$ 36.01$3-1/4" PAH-3250 same PA-3250 250 / Carton 157.75$ 39.44$3-3/4" PAH-3750 same PA-3750 250 / Carton 164.10$ 41.03$4-1/2" PAH-4500 same PA-4500 250 / Carton 192.65$ 48.16$

5" PAH-5000 same PA-5000 250 / Carton 215.00$ 53.75$6" PAH-6000 same PA-6000 250 / Carton 252.80$ 63.20$7" PAH-7000 same PA-7000 200 / Carton 317.10$ 63.42$8" PAH-8000 same PA-8000 200 / Carton 341.20$ 68.24$

One (1) Driver Bit included with every 1,000 fasteners (TD-30 #3 Phillips Bit for PA's and HH-250-N 1/4" Hex Bit for PAH's)


8 Trufast Catalog: Roofing Fasteners

ROOFING FASTENERSThe TRUFAST® #14 HD Fastener is an ideal "all-purpose fastener" for use in corrugated steel, structural concrete, and wood roof decksfor insulation or lap attachment. Allow a minimum of 3/4" penetration through the underside of steel decks and a minimum of 1" embedmentin wood plank. Pre-drilling is required for concrete using a 3/16" drill bit; pre-drilled hole must be at least 1/2" deeper that the length ofthe fastener to allow for debris in the hole. FM and Miami-Dade Approved.

HD #14 Heavy Duty Drill Point, #3 Phillips Truss Head, Black E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-1/2" HD-1500 same 1000 / Bucket 13.7 lbs. 36.30$ 36.30$

2" HD-2000 same 1000 / Bucket 17.2 lbs. 40.70$ 40.70$2-1/2" HD-2500 same 1000 / Bucket 20.7 lbs. 45.95$ 45.95$




6" HD-6000 same 1000 / Bucket 46.2 lbs. 134.65$ 134.65$7" HD-7000 same 500 / Bucket 27.0 lbs. 185.30$ 92.65$8" HD-8000 same 500 / Bucket 30.7 lbs. 208.00$ 104.00$9" HD-9000 same 250 / Bucket 16.6 lbs. 281.20$ 70.30$10" HD-10000 same 250 / Bucket 18.5 lbs. 315.75$ 78.94$11" HD-11000 same 250 / Bucket 20.1 lbs. 441.70$ 110.43$12" HD-12000 same 250 / Bucket 22.0 lbs. 468.40$ 117.10$


HD #14 Heavy Duty Drill Point, #3 Phillips Truss Head, White E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-1/4" HD-W1250 HD-1250-W 1000 / Bucket 11.9 lbs. 94.15$ 94.15$2-1/4" HD-W2250 HD-2250-W 1000 / Bucket 19.0 lbs. 99.35$ 99.35$2-7/8" HD-W2875 HD-2875-W 1000 / Bucket 23.5 lbs. 113.55$ 113.55$3-1/4" HD-W3250 HD-3250-W 1000 / Bucket 26.1 lbs. 130.20$ 130.20$3-3/4" HD-W3750 HD-3750-W 1000 / Bucket 29.6 lbs. 153.85$ 153.85$

4" HD-W4000 HD-4000-W 1000 / Bucket 31.3 lbs. 143.20$ 143.20$4-1/2" HD-W4500 HD-4500-W 1000 / Bucket 35.2 lbs. 164.60$ 164.60$

5" HD-W5000 HD-5000-W 1000 / Bucket 38.7 lbs. 183.25$ 183.25$6" HD-W6000 HD-6000-W 1000 / Bucket 46.2 lbs. 199.75$ 199.75$7" HD-W7000 HD-7000-W 500 / Bucket 27.0 lbs. 252.90$ 126.45$8" HD-W8000 HD-8000-W 500 / Bucket 30.7 lbs. 286.60$ 143.30$9" HD-W9000 HD-9000-W 250 / Bucket 16.6 lbs. 379.65$ 94.91$10" HD-W10000 HD-10000-W 250 / Bucket 18.5 lbs. 474.55$ 118.64$12" HD-W12000 HD-12000-W 250 / Bucket 22.0 lbs. 544.80$ 136.20$


HD-SS #14 Heavy Duty Stainless Steel Drill Point, #3 Phillips Truss HeadLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-1/2" HD-1500-SS same 1000 / Bucket 13.3 lbs. 178.15$ 178.15$

2" HD-2000-SS same 1000 / Bucket 16.5 lbs. 221.55$ 221.55$3" HD-3000-SS same 1000 / Bucket 24.0 lbs. 310.65$ 310.65$4" HD-4000-SS same 1000 / Bucket 31.8 lbs. 406.85$ 406.85$5" HD-5000-SS same 1000 / Bucket 38.0 lbs. 492.55$ 492.55$6" HD-6000-SS same 1000 / Bucket 44.0 lbs. 581.50$ 581.50$7" HD-7000-SS same 500 / Bucket 26.8 lbs. 703.70$ 351.85$8" HD-8000-SS same 500 / Bucket 29.6 lbs. 780.30$ 390.15$10" HD-10000-SS same 250 / Bucket 17.6 lbs. 980.65$ 245.16$12" HD-12000-SS same 250 / Bucket 21.9 lbs. 1,203.05$ 300.76$




ROOFING FASTENERSTRUFAST® #15 EHD Fasteners are engineered for lap attachment in higher wind uplift roof assemblies. Allow aminimum of 3/4" penetration through the underside of steel decks. FM and Miami-Dade Approved.

EHD #15 Extra Heavy Duty Drill Point, #3 Phillips Truss Head, Black E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-1/4" EHD-1250-15 EHD-1250 1000 / Bucket 12.6 lbs. 61.10$ 61.10$

2" EHD-2000-15 EHD-2000 1000 / Bucket 19.5 lbs. 77.25$ 77.25$3" EHD-3000-15 EHD-3000 1000 / Bucket 29.9 lbs. 98.40$ 98.40$4" EHD-4000-15 EHD-4000 1000 / Bucket 39.0 lbs. 117.80$ 117.80$5" EHD-5000-15 EHD-5000 1000 / Bucket 48.0 lbs. 148.20$ 148.20$6" EHD-6000-15 EHD-6000 500 / Bucket 27.9 lbs. 190.10$ 95.05$7" EHD-7000-15 EHD-7000 500 / Bucket 32.6 lbs. 259.20$ 129.60$8" EHD-8000-15 EHD-8000 500 / Bucket 37.3 lbs. 292.20$ 146.10$9" EHD-9000-15 EHD-9000 250 / Bucket 20.9 lbs 457.60$ 114.40$10" EHD-10000-15 EHD-10000 250 / Bucket 23.2 lbs. 493.50$ 123.38$11" EHD-11000-15 EHD-11000 250 / Bucket 25.3 lbs. 510.20$ 127.55$12" EHD-12000-15 EHD-12000 250 / Bucket 27.7 lbs. 628.60$ 157.15$14" EHD-14000-15 EHD-14000 250 / Bucket 32.3 lbs. 699.35$ 174.84$16" EHD-16000-15 EHD-16000 250 / Bucket 36.9 lbs. 798.40$ 199.60$18" EHD-18000-15 EHD-18000 250 / Bucket 41.7 lbs. 1,020.40$ 255.10$20" EHD-20000-15 EHD-20000 250 / Bucket 46.7 lbs. 1,177.80$ 294.45$22" EHD-22000-15 EHD-22000 250 / Bucket 51.7 lbs. 1,353.50$ 338.38$24" EHD-24000-15 EHD-24000 250 / Bucket 56.4 lbs. 1,422.45$ 355.61$


EHD #15 Extra Heavy Duty Drill Point, #3 Phillips Truss Head, White E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg

2" EHD-W2000-15 EHD-2000-W 1000 / Bucket 19.5 lbs. 289.95$ 289.95$3" EHD-W3000-15 EHD-3000-W 1000 / Bucket 29.9 lbs. 209.25$ 209.25$4" EHD-W4000-15 EHD-4000-W 1000 / Bucket 39.0 lbs. 191.00$ 191.00$5" EHD-W5000-15 EHD-5000-W 1000 / Bucket 48.0 lbs. 223.45$ 223.45$6" EHD-W6000-15 EHD-6000-W 500 / Bucket 27.9 lbs. 294.00$ 147.00$7" EHD-W7000-15 EHD-7000-W 500 / Bucket 32.6 lbs. 357.00$ 178.50$8" EHD-W8000-15 EHD-8000-W 500 / Bucket 38.5 lbs. 404.75$ 202.38$10" EHD-W10000-15 EHD-10000-W 250 / Bucket 23.1 lbs. 586.35$ 146.59$11" EHD-W11000-15 EHD-11000-W 250 / Bucket 25.3 lbs. 623.90$ 155.98$12" EHD-W12000-15 EHD-12000-W 250 / Bucket 27.7 lbs. 786.75$ 196.69$


TRUFAST® #12 PFC Purlin Fasteners are designed for attaching single-ply membrane systems to structural steelpurlins up to 3/16" thick. Allow a minimum of 1" penetration through the purlin. For best results, install fastenersusing a screwgun no faster than 1800 rpm.

PFC Purlin Fasteners, 1/4" Sq. Drive, Pancake Head, Black E-coatSize Part No. New Part No. Pkg. Qty / Type Wgt/Pkg Price/1000 Price/Pkg1-3/8" PFC-1375 PF-1375 2500 / Bucket 29.0 lbs. 65.40$ 163.50$2-3/4" PFC-2750 PF-2750 1000 / Bucket 21.7 lbs. 70.10$ 70.10$3-3/4" PFC-3750 PF-3750 1000 / Bucket 28.7 lbs. 128.35$ 128.35$4-3/4" PFC-4750 PF-4750 1000 / Bucket 35.1 lbs. 162.45$ 162.45$5-3/4" PFC-5750 PF-5750 1000 / Bucket 43.4 lbs. 205.50$ 205.50$6-3/4" PFC-6750 PF-6750 1000 / Bucket 50.9 lbs. 275.45$ 275.45$7-3/4" PFC-7750 PF-7750 500 / Bucket 29.4 lbs. 297.50$ 148.75$8-3/4" PFC-8750 PF-8750 500 / Bucket 31.7 lbs. 305.20$ 152.60$

One (1) #3 Sq. Drive Bit SQ-30 included per pkg.



ROOFING FASTENERSThe Trufast® Concrete Spike is a one-piece, vibration-resistant anchor designed to fasten insulation, single-ply roof membrane,wood, and steel to structural concrete roof decks. Featuring an "S" shapped configuration at the working end of the fastener to create an expansion mechanism, it provides a fast, reliable fastening solution for structural concrete roof applications.

1/4" Dia. Concrete Spike, Black E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-1/4" TS250-1250 same 500 11.3 lbs. 82.05$ 41.03$1-1/2" TS250-1500 same 500 13.0 lbs. 94.85$ 47.43$

2" TS250-2000 same 500 16.8 lbs. 117.55$ 58.78$2-1/2" TS250-2500 same 500 20.4 lbs. 130.30$ 65.15$






8" TS250-8000 same 250 28.9 lbs. 484.65$ 121.16$9" TS250-9000 same 250 32.5 lbs. 555.60$ 138.90$10" TS250-10000 same 250 36.0 lbs. 588.55$ 147.14$11" TS250-11000 same 100 15.8 lbs. 775.10$ 77.51$12" TS250-12000 same 100 17.2 lbs. 912.60$ 91.26$13" TS250-13000 same 100 18.6 lbs. 1,016.85$ 101.69$14" TS250-14000 same 100 20.0 lbs. 1,107.60$ 110.76$15" TS250-15000 same 100 21.3 lbs. 1,287.50$ 128.75$16" TS250-16000 same 100 22.6 lbs. 1,416.25$ 141.63$

NOTE: Pre-drill hole using 1/4" dia. drill bit.

The Trufast® Fluted Concrete Nail is designed to secure insulation, coverboards, single-ply roof membrane, wood, and steelto structural concrete. It is a reliable and cost-effective fastening alternative to other mechanical fastening solutions.

Fluted Nail Concrete Fasteners, Black E-coatLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg1-1/2" TG-1500 same 500 / Bucket 8.3 lbs. 53.85$ 26.93$

2" TG-2000 same 500 / Bucket 9.6 lbs. 73.25$ 36.63$2-1/2" TG-2500 same 500 / Bucket 12.1 lbs. 84.70$ 42.35$




6" TG-6000 same 500 / Bucket 28.5 lbs. 194.60$ 97.30$7" TG-7000 same 500 / Bucket 34.3 lbs. 225.95$ 112.98$8" TG-8000 same 500 / Bucket 37.7 lbs. 339.60$ 169.80$9" TG-9000 same 250 / Bucket 21.3 lbs. 377.85$ 94.46$10" TG-10000 same 250 / Bucket 23.3 lbs. 410.80$ 102.70$11" TG-11000 same 250 / Bucket 28.8 lbs. 458.55$ 114.64$12" TG-12000 same 250 / Bucket 31.2 lbs. 503.65$ 125.91$

NOTE: Pre-drill hole using 3/16" dia. drill bit.



ROOFING FASTENERS

The TRUFAST® TL Fastener is a glass-filled nylon auger fastener designed to secure roof insulation and single-ply membrane to gypsum and cementitious wood fiber (i.e. Tectum ®) decks. Its tapered shank and large threaddesign provide excellent penetration into the base material for high pull-out resistance. Use with a MPTL-30003" plate for insulation attachment and a MPTL-2000 2" plate for membrane attachment. NOTE: TL Fasteners can beinstalled into some cementitious wood fiber decks without pre-drilling. A pilot hole is required for gypsum and mustbe a minimum of 1/2" deeper than the embedment. Diameter of drill bit should be determined by pull-out test results.

TL Lightweight Nylon FastenersLength Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg

2' TL-2000 same 500 / Carton 11 lbs. 184.15$ 92.08$2-1/2" TL-2500 same 500 / Carton 13 lbs. 185.25$ 92.63$

3" TL-3000 same 500 / Carton 15 lbs. 203.65$ 101.83$3-1/2" TL-3500 same 500 / Carton 17 lbs. 222.10$ 111.05$





8" TL-8000 same 250 / Carton 17.5 lbs. 406.40$ 101.60$8-1/2" TL-8500 same 250 / Carton 19 lbs. 430.55$ 107.64$


10" TL-10000 same 250 / Carton 22 lbs. 503.65$ 125.91$11" TL-11000 same 250 / Carton 25 lbs. 587.55$ 146.89$12" TL-12000 same 250 / Carton 26 lbs. 636.25$ 159.06$13" TL-13000 same 250 / Carton 28 lbs. 652.25$ 163.06$14" TL-14000 same 250 / Carton 29 lbs. 684.15$ 171.04$

One (1) 1/4" Drive Bit included per pkg.

TL PlatesSize Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg

2" Membrane TLP-2 MPTL-2000 1000 / Carton 14 lbs. 67.60$ 33.80$3" Insulation TLP-3 MPTL-3000 500 / Carton 17.5 lbs. 83.85$ 41.93$

MPTL-3000MPTL-2000



100 COUNT PACKAGES

DP #12 Drill Point, #3 Phillips Truss Head, Black E-coat Length Part No. New Part No. Price/100/c 1-5/8" DP-1625C DP-1625-100 6.00$2-1/4" DP-2250C DP-2250-100 6.55$2-7/8" DP-2875C DP-2875-100 7.10$3-1/4" DP-3250C DP-3250-100 8.15$3-3/4" DP-3750C DP-3750-100 8.55$4-1/2" DP-4500C DP-4500-100 10.05$

5" DP-5000C DP-5000-100 11.95$6" DP-6000C DP-6000-100 14.85$

Fasteners packed 100 pieces per carton NOTE: must be ordered in master cartons of 5 (500 pcs.)

HD #14 Heavy Duty Drill Point, #3 Phillips Truss Head, Black E-coat Length Part No. New Part No. Price/100/c 1-1/2" HD-1500C HD-1500-100 6.15$

2" HD-2000C HD-2000-100 6.80$2-1/2" HD-2500C HD-2500-100 7.60$

3" HD-3000C HD-3000-100 9.60$3-1/2" HD-3500C HD-3500-100 11.85$

4" HD-4000C HD-4000-100 13.50$4-1/2" HD-4500C HD-4500-100 14.85$

5" HD-5000C HD-5000-100 18.65$5-1/2" HD-5500C HD-5500-100 20.05$

6" HD-6000C HD-6000-100 22.00$Fasteners packed 100 pieces per carton NOTE: must be ordered in master cartons of 5 (500 pcs.)

Galvalume™ PlatesDescription Part No. New Part No. Pkg Qty/Type Price/100/c

2" Galvalume ™ (carton) MP-2-TFC MP-2000-100 100/Box 8.40$MP-3-TFC MP-3000-100 100/Box 8.15$

Fasteners packed 100 pcs per ctn Note: must be ordered in master cartons of 10 (1,000 pcs.)

Price / Master Carton$84.00

3" Galvalume ™ $81.50

$30.75$34.00$38.00$48.00$59.25$67.50$74.25$93.25$100.25$110.00

Price / Master Carton

Price / Master Carton$30.00$32.75$35.50$40.75$42.75$50.25$59.75$74.25


13Trufast Catalog: Stress Plates and Batten Bar

STRESS PLATES & BATTEN BAR

Galvalume™ PlatesSize & Type Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000/pkg

2" Seam Plate MP-2-TF MP-2000 1000 / Bucket 27 lbs. 57.65$

2" Barbed Seam Plate MPB-2-TF MPB-2000 1000 / Bucket 28 lbs. 60.95$

2.4" Barbed Seam Plate MPB-2400 SAME 1000 / Bucket 52 lbs. 80.80$

3" Insulation Plate MP-3-TF MP-3000 1000 / Bucket 34 lbs. 58.30$

3" Recessed Insulation Plate MPH-3-TF MPR-3000 1000 / Bucket 37 lbs. 58.30$

Note: MP and MPB Plates are for use with Phillips Truss Head Fasteners only. MPR Plate is recessed and can be used with either Hex Head or Phillips Truss Head Fasteners

Galvalume ™ Seam/Batten BarLength Part No. New Part No. Ft/Pkg/ Type Wgt/Pkg Price / Ft

10' BB-18 BB-18F-6 500' / 3.5" Tube 85 lbs. 0.22$

10' BB-18-R BB-18R-6 500' / 3.5" Tube 85 lbs. 0.22$

PUNCHED 6" OR 12" ON CENTER

BB-18F BB-18R (RECESSED)

MP‐2000 MPB‐2000MPB‐2400 MP‐3000


14 Trufast Catalog: Termination Bar & Nailins

TERMINATION BAR & NAILINS

Aluminum Termination BarLength Part No. New Part No. Ft/Pkg /Type Wgt/Pkg Price / Ft Punched O.C.

10' TB-50 same 500' / 4" Tube 40 lbs. 0.28$ 6" or 8"

10' TB-75 same 500' / 3.5"Tube 50 lbs. 0.31$ 6", 8" or 12"10' TB-90 TB-90F-6 500' / 3.5"Tube 55 lbs. 0.35$ 6" or 8"

10' TB-100-6 same 500' / 4" Tube 65 lbs. 0.40$ 6" or 8"

10' TB-125-6 same 500'/ 4" Tube 75 lbs. 0.48$ 6" or 8"

Stainless Steel Flat Bar10' TB-125-SS TB-125-6-SS 200'/3.5"Tube 98 lbs. 3.57$ 6"10' NEW TB-75-6-SS 200'/3.5"Tube 49 lbs. 2.85$ 6"

Aluminum Gravel/Drain BarLength Part No. New Part No. Ft/Pkg / Type Wgt/Pkg Price / Ft

10' RD-100 TB-100-RD 100' / 5" Tube 46 lbs. 1.31$

Note: Punched 6" on center only.

ZAMAC NailinsSize Part No. New Part No. Pkg Qty / Type Wgt/Pkg Price/100/c

3/16 X 7/8" CZN-0875 ZN-0875-100 100 / Box 1.2 lbs. 5.00$1/4 X 1" CZN-1000 ZN-1000-100 100 / Box 2.0 lbs. 7.00$

1/4 X 1-1/4" CZN-1250 ZN-1250-100 100 / Box 2.4 lbs. 7.70$1/4 X 1-1/2" CZN-1500 ZN-1500-100 100 / Box 2.6 lbs. 8.60$

1/4 X 2" CZN-2000 ZN-2000-100 100 / Box 3.2 lbs. 9.90$ Note: Sold in 100 count boxes. Master Carton contains five (5) 100 count boxes (500 pcs.). SOLD ONLY IN MASTER CARTONS Also available in Stainless Steel upon request. Consult factory for price and delivery.

Price / Master Carton$25.00$35.00$38.50$43.00$49.50

TB-50

TB-90 & TB-125 TB-75 & TB-100

TB-100-RD


15Trufast Catalog: SIP Fasteners

SIP FASTENERSTRUFAST® SIP Fasteners are specifically engineered for attaching structural insulated panels (SIPs) and nail base panels to woodand metal framing. Featuring a large, low-profile pancake head with a 6-lobe drive, they drive quickly and smoothly, and draw panelssecurely without the need of a washer. Three point/thread styles are offered for use in wood, corrugated steel, and steel members withoutpre-drilling.

SIPTP (Thread Point): For wood and timber applications.SIPLD (Light-duty Drill Point): For corrugated steel decks and wood applications.SIPHD (Heavy-duty Drill Point): For structural steel members (up to 3/16" thick without pre-drilling)

SIPTP Structural Insulated Panel Fasteners, Thread PointPancake Head with T-30 6-Lobe Drive, Black E-coat

Length SIPTP Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg2" SIPTP-2000 same 500 / Bucket 10.1 lbs. 76.75$ 38.38$

2-1/2" SIPTP-2500 same 500 / Bucket 12.1 lbs. 79.20$ 39.60$3" SIPTP-3000 same 500 / Bucket 14.0 lbs. 81.50$ 40.75$






8-1/2" SIPTP-8500 same 250 / Bucket 18.3 lbs. 255.20$ 63.80$9" SIPTP-9000 same 250 / Bucket 19.3 lbs. 262.55$ 65.64$10" SIPTP-10000 same 250 / Bucket 21.0 lbs. 299.75$ 74.94$11" SIPTP-11000 same 250 / Bucket 22.8 lbs. 318.10$ 79.53$12" SIPTP-12000 same 250 / Bucket 24.8 lbs. 339.60$ 84.90$13" SIPTP-13000 same 250 / Carton 26.9 lbs. 364.15$ 91.04$14" SIPTP-14000 same 250 / Carton 29.1 lbs. 446.00$ 111.50$15" SIPTP-15000 same 250 / Carton 31.2 lbs. 469.20$ 117.30$16" SIPTP-16000 same 250 / Carton 32.9 lbs. 506.40$ 126.60$18" SIPTP-18000 same 250 / Carton 36.8 lbs. 561.20$ 140.30$

NOTE: Two (2) T-30 Driver Bits included in each package.


16 Trufast Catalog: SIP Fasteners

SIP FASTENERSSIPLD Structural Insulated Panel Fasteners, Light-Duty #2 Drill PointPancake Head with T-30 6-Lobe Drive, Black E-coat

Length SIPLD Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg3" SIPLD-3000 same 500 / Bucket 14.1 lbs. 81.50$ 40.75$

3-1/2" SIPLD-3500 same 500 / Bucket 16.1 lbs. 89.15$ 44.58$4" SIPLD-4000 same 500 / Bucket 18.4 lbs. 99.10$ 49.55$






9 -1/2" SIPLD-9500 same 250 / Bucket 20.0 lbs. 281.15$ 70.29$10" SIPLD-10000 same 250 / Bucket 21.5 lbs. 299.75$ 74.94$11" SIPLD-11000 same 250 / Bucket 22.8 lbs. 318.10$ 79.53$12" SIPLD-12000 same 250 / Bucket 24.8 lbs. 339.60$ 84.90$13" SIPLD-13000 same 250 / Carton 26.9 lbs. 364.15$ 91.04$14" SIPLD-14000 same 250 / Carton 29.1 lbs. 446.00$ 111.50$15" SIPLD-15000 same 250 / Carton 30.8 lbs. 469.20$ 117.30$16" SIPLD-16000 same 250 / Carton 32.9 lbs. 506.40$ 126.60$18" SIPLD-18000 same 250 / Carton 38.0 lbs. 561.20$ 140.30$


SIPLD Fasteners are designed for attaching panels to wood and 22 - 18 ga. corrugated steel decks.

SIPHD Structural Insulated Panel Fasteners, Heavy-Duty #4 Drill PointPancake Head with T-30 6-Lobe Drive, Black E-coat

Length SIPHD Part No. New Part No. Pkg Qty/Type Wgt/Pkg Price/1000 Price/Pkg6" SIPHD-6000 same 500 / Bucket 33.4 lbs. 226.70$ 113.35$8" SIPHD-8000 same 250 / Bucket 20.9 lbs. 343.50$ 85.88$

9 3/4" SIPHD-9750 same 250 / Bucket 25.9 lbs. 366.75$ 91.69$11 3/4" SIPHD-11750 same 250 / Bucket 31.4 lbs. 400.40$ 100.10$13 3/4" SIPHD-13750 same 250 / Carton 35.7 lbs. 435.85$ 108.96$


SIPHD Fasteners are designed for attaching panels to 16 ga. - 3/16" steel members without pre-drilling.


17Trufast Catalog: Tools

TRUFAST Shorty Tool AttachmentManufacturer Model Trufast Part# New Part No. Pkg. Qty. Price EAShorty Tool for Roofing Fasteners A-ST same 1 127.00$

A-SST same 1 145.20$Requires Milwaukee Model 6792-20 Screw Gun (not included)

Shorty Tool Replacement PartA-STDS same 1 1.4 lbs. 25.00$

Electric Screw GunTrufast Part# New Part No. RPM Price EA

Milwaukee Model 6792-20 A-MSG same 2,500 144.80$

TRUFAST PA Standup ToolsModel No. New Part No. Qty/Carton Wgt/Pkg Price EA

29" Tool & Electric Screw Gun* A-PA-CT same 1 4 lbs. 334.00$ Tool features a Milwaukee Model MILW 6792-20 (2500 rpm) Screw Gun

PA Tool Assembly AttachmentLength / Screw Gun Brand Model No. New Part No. Qty/Carton Wgt/Pkg Price EA29" / Milwaukee A-PA-UBA same 1 1 lbs. 193.55$Assembly includes everything needed except Milwaukee Model 6792-20 Screw Gun

PA Tool Replacement Tool PartsLower body Assembly A-PA-LBA same 1 1 lbs. 45.00$20" Drive Shaft A-PA-20-DS same 1 1.2 lbs. 27.00$

TRUFAST PA System AccessoriesDescription Part No. New Part No. Pkg. Qty. Wgt./Pkg. Price EA

A-PA-BAG same 1 1.0 lb. 16.70$PA Bag & Setter Tool Combo A-PA-SBC same 1 2.5 lbs. 48.40$PA Bag

TOOLS

Shorty Tool for SIP Fasteners

Shorty Tool Drive Shaft

Manufacturer Model

Length / Description


18 Trufast Catalog: Drill and Driver Bits

DRILL & DRIVER BITSStraight Shank Drill Bits

Diameter Overall Length Usable Length Part No. Price EA3/16" 4" 2-1/2" 4000-SDB DRL-SDB187-4000 2.52$

SDS Shank Drill Bits for use with Rotary Hammer Drills

Diameter Overall Length Usable Length New Part # Price/ea3/16" 4" 2" DRL-SDSB187-4000 6.12$ 3/16" 6" 4" DRL-SDSB187-6000 6.12$ 3/16" 8" 6" DRL-SDSB187-8000 7.71$ 3/16" 10" 8" DRL-SDSB187-10000 9.64$ 3/16" 12" 10" DRL-SDSB187-12000 13.44$ 3/16" 14" 12" DRL-SDSB187-14000 18.43$ 7/32" 8" 6" DRL-SDSB218-8000 8.98$ 7/32" 11" 9" DRL-SDSB218-11000 10.89$ 7/32" 14" 12" DRL-SDSB218-14000 14.77$ 1/4" 6" 4" DRL-SDSB250-6000 5.64$ 1/4" 8" 6" DRL-SDSB250-8000 6.00$ 1/4" 11" 9" DRL-SDSB250-11000 14.28$ 1/4" 14" 12" DRL-SDSB250-14000 14.70$ 1/4" 16" 14" DRL-SDSB250-16000 17.96$

DRILL BIT SPECIFICATIONS SDB Straight Shank: 1-1/2" of shank above flute to allow for chucking into drill.

SDSB: Use with Rotary Hammer Drill. Allow for 2" of shank above flute for chucking into drill.

Note: All pre-drilled holes should be drilled 1/2" deeper than installed screw depth to allow for debris. Note: Use 3/16" diameter drill bits for Heavy Duty (#14) fasteners & Fluted Nails. Use 7/32" diameter drill bits for EHD fasteners Use 1/4" diameter drill bits for ZAMACS and 1/4" Tru-Spikes.

Driver BitsDescription For Use With Part No. Price/ea.

#2 Phillips x 2" Driver Bit #2 Phillips Head Fasteners TD-20 1.01$ #3 Phillips x 2" Driver Bit #3 Phillips Head Fasteners TD-30 1.01$ #3 Square x 2" Driver Bit Purlin Fastener SQ-30 1.41$ 1/4" Square Driver Bit TL Fastener SQ-250 2.20$ 1/4" x 2" Hex Head Nutsetter DPH HH-250-N 1.90$ T-30 6-Lobe Driver Bit SIPTP, SIPLD, SIPHD T-30 2.50$BIT-T30-2000

New Part No.BIT-PH2-2000BIT-PH3-2000BIT-S3-2000

BIT-S250-1250BIT-H250-1750

10", 11", 12" 16000-SDSB-4

2.59$

New Part #

DRL-SDB187-6000

3-3/4", 4-1/4", 5" 8000-SDSB-46", 7", 8" 11000-SDSB-4

10" 14000-SDSB-4

6", 7", 8" 11000-SDSB-73210", 11", 12" 14000-SDSB-732

1-1/4" thru 3-1/4" 6000-SDSB-4

8" 12000-SDSB10" 14000-SDSB

3-3/4", 4-1/4", 5" 8000-SDSB-732

6", 7" 10000-SDSB

6000-SDB3-1/4", 3-3/4"

For Use WithScrew Lengths Part No.

4000-SDSB1-1/4" thru 3-1/4" 6000-SDSB3-3/4", 4-1/4", 5" 8000-SDSB

For Use WithScrew Lengths

3/16" 6" 4-1/2" 1-1/4", 1-3/4", 2-1/4", 2-3/4",


19Trufast Catalog: Base Sheet Fasteners & Accessories

BASE SHEET FASTENERS & ACCESSORIESTwin Loc-NailsFor base sheet and insulation attachment to lightweight insulating concrete, cementitious wood fiber (Tectum®)and poured gypsum roof decks.

Part / Length Part # Qty / Carton Carton Wgt. Qty / Skid Price / M Price / Ctn.

Twin Loc-Nail, 1.4" (35.6 mm) TWL-1400 500 26 lbs. 15,000 $198.00 $99.50

Twin Loc-Nail, 1.8 " (45.7 mm) TWL-1800 500 28 lbs. 15,000 $198.00 $99.50




Twin Loc-Nail w/o plate, 1.4" (35.6 mm) R-TWL-1400 1,000 22 lbs. 50,000 $165.00 $165.00

Twin Loc-Nail w/o plate, 1.8" (45.7 mm) R-TWL-1800 1,000 24 lbs. 50,000 $165.00 $165.00

Part / Length Part # Qty / Carton Carton Wgt. Qty / Skid Price /ft Price / Ctn.

Straight Line Batten Bar BB-20R-3 100 ft. 13 lbs. 4,000 ft. $0.34 $34.00NOTE: Straight Line Batten Bar is always plus freight unless accompanied

by a 25m piece Twin Loc-Nail w/o plate order.

FM Series Fastener / Disk UnitsFor base sheet attachment to lightweight insulating concrete and poured gypsum roof decks.

Part / Length Part # Qty / Carton Carton Wgt. Qty / Skid Price / M Price / Ctn.

FM-90, 1.7" FM-90-1700 1,000 40 lbs. 18,000 $98 $98.00

FM-75, 1.2" FM-75-1200 1,000 35 lbs. 18,000 $98 $98.00

FM-290, 1.7" FM-290-1700 500 34 lbs. 9,000 $180 $90.00

Insuldeck Loc-NailFor base sheet attachment to cementitious wood fiber (Tectum®) roof decks.

Part / Length Qty / Carton Carton Wgt. Qty / Skid Price / M Price / Ctn.Insuldeck Loc-Nail, 1.7" IDL-1700 1,000 29 lbs. 18,000 85$ $85.00

Do-All Loc-NailsShingle or base ply attachment to Loadmaster and Martin Fireproofing Deck Systems.

Part / Length Part # Qty / Carton Carton Wgt. Price / M Price / Ctn.

Do-All Loc-Nail, 1.375" DA-1375 2,500 13 lbs. $58.00 $145.00

Do-All Loc-Nail, 1.375" Master Box DA-1375-MSTR 10,000 52 lbs. $58.00 $580.00

Do-All Loc-Nail, 1.75" DA-1750-YZ 2,500 16 lbs. $72.00 $180.00

Assembled Do-All Loc-Nail, 1.375" (only) DA-1375-PA 1,000 10 lbs. $108.00 $108.00

Do-All Loc-Nail Metal Caps, 1.625" dia. DAMC-1625 2,500 16 lbs. $31.00 $77.50

Stainless Do-All Loc-Nail, 1.375" DA-1375-SS 2,500 13 lbs. $96.00 $240.00

Stainless Do-All Loc-Nail, 1.75" DA-1750-SS 2,500 16 lbs. $106.00 $265.00

FM-90

FM-290

Straight Line

R-TWL-XXXX

TWL-XXXX

Effective 1.1.14 14 CONNECTIVE

20 Trufast Catalog: Base Sheet Fasteners & Accessories

BASE SHEET FASTENERS & ACCESSORIESTools & Accessories

Item Part # Qty / Carton Carton Wgt. Price / ea.

Twin Loc Driver A-ES-TWL 6 36 lbs. $75.00

Twin Loc Insulation Driver 2 14 lbs. $75.00

FM-290 Driver 6 36 lbs. $75.00

Insuldeck Driver 6 36 lbs. $75.00

Twin Loc Hand Tool* 1 1 lb. $25.00

Twin Loc Air Tool Nose Piece* 1 3 lbs. $50.00

Nail Pouch A-ES-BAG 20 20 lbs. $20.00

* Specialty tool for installation of Twin Loc-Nails into lightweight insulating concrete and Tectum™ roof decks.

Twin Loc

FM-290

Effective 1.1.14 15 CONNECTIVE

21Trufast Catalog: Adhesives & Sealants

ADHESIVES & SEALANTSDow INSTA STIK™ Quik Set Commercial Roofing AdhesiveDow INSTA STIK Quik Set is a single-component polyurethane adhesive designed to attachcompatible roof insulation boards to roof decks and substrates in new roof and replacement applications.

PRODUCT FEATURES

Part No. Description CONNECTIVE308916 INSTA STIK Quik Set -- Tank Only $166.85

31 lbs/tank -- 40 tanks/pallet Cost/Sq.Ft. $0.209

Instructions included in each carton Cost/Square $20.86Freight prepaid on 1+ pallet quantities

INSTA STIK Dispensing Accessories

Hose & Wand Dispensing KitPart No. Qty. 1 Qty. 3 Qty. 5+

IS1D $30.80 $28.50 $25.00

NOTE: Approximately 3 tanks per kit.

Assembled kit shown with tank.

Multi-Bead Applicator (MBA) Cart Assembly

Part No. Price Ea.

158414 $1,025.00

NOTE: Please allow one week for delivery.

Price Ea.

• Dispensed from a portable, pre-pressurized container (30 lb. unit / 23 lb. net chemical)requiring no external power source.

• Yield: 8 to 9 squares per tank (at 3/4" to 1" bead size and 12" o.c. spacing).• 15 month shelf life.• 3 to 6 minute tack time and approximately 4 hour cure time (depending on humidity).• Approved for use on concrete, Tectum™ (cementitious wood fiberboard), wood, tapered

systems, and multi-level insulation.• FM, UL, and Miami-Dade Approvals• 10 to 20 year warranties available; must submit Dow Job Qualification Form.

Kit includes 4' hose,on/off valve, 2-pc. wand,


22 Trufast Catalog: Adhesives & Sealants

ADHESIVES & SEALANTSDow FROTH-PAK™ Spray Polyurethane Foam Sealant

Dow FROTH-Pak™ Foam Sealant is a two‐component, quick‐cure spraypolyurethane foam that fills cavities, penetrations, cracks and expansion joints.FROTH-PAK Foam Sealant can also be used as a sealant and void fill inmany roofing applications. FROTH-PAK Foam is chemically cured, significantlyreducing curing time. It dispenses, expands, and becomes tack-free in secondsand completely cures in minutes.

TYPICAL APPLICATIONS

Part No. Description CONNECTIVE

346963 FROTH-PAK 200 Kit (1.75 pcf) $281.6531 lbs/kit -- 26 kits/palletInstructions included in each carton Freight prepaid on 1+ pallet quantities

Kit includes 1 ea. A and B components, 1 gun/hose assy., 6 cone spray and 4 fan spray nozzles.

FROTH-PAK Kit AccessoriesPart No. Description Price Ea.

259219 Cone Spray Nozzle -- Low Output (green / white back) $29.00Pack of 25 nozzles

158398 GHA 15' Gun & Hose Assembly $58.00Includes 1 dispensing gun, 2 chemical hoses, 5 gram lubricating packet, 8 cone spray and 4 fan spray nozzles.

• SPF roof repair and patch.• Insulation joint sealant.

• Leveling and sloping.

• Vapor barrier in sealing roof perimeters and parapet walls.

• Sealing spline joints of SIP roof and wall panels.

Yield: Approx. 200 board feet or 16.6 cubic feet per kit.


23Trufast Catalog: Adhesives & Sealants

ADHESIVES, SEALANTS AND ACCESSSORIES

Part No. Less than 2 Pallets 2-7 Pallets 7 + Pallets308276 $154.08 $144.45 $130.00

Each canister will adhere approximately 750 Flat profile, Field Tiles (.7 squares)

Withstands up to 150 mph wind speeds in specific applications

308941 $184.20 $172.44 $159.00

Each can will adhere approximately 70 Flat profile, Field Tiles (.7 squares)Withstands up to 150 mph wind speeds in specific applications

TILE BOND / AccessoriesPart No. Price/ea.235597 $40.00

28 lbs/case -- 12 cans/case -- 64 cases/pallet. (sold / priced per case) (12 month shelf life)

DescriptionGun/Hose Assembly

TILE BOND Price Per Kit / 40 = 1 palletDescription

TILE BOND (Complete Kit)23 lbs/kit -- 40 kits/pallet. Each kit includes: Hose, dispenser, coupler, valve, wrench, and instructions (12 month shelf life)

TILE BOND (28 oz. Cans)


24 Trufast Catalog: Adhesives & Sealants & Accessories

ADHESIVES, SEALANTS AND ACCESSSORIESMILLENNIUM ONE STEP™ FOAMABLE ADHESIVE Shelf Life: 12 months Yield: Approx. 6 squares per case @ 12" o.c., 1/4 "- 1/2" beads

1 case- 191 cases 192 case +Part No. Description Less than 4 Pallets 4+ Pallets

MILL-OS-FA15-04 MILLENNIUM ONE STEP™ FOAMABLE ADHESIVE $126.00 $118.00Instructions included in each carton.20 lbs/case -- 48 cases/pallet

MILLENNIUM DISPENSING ACCESSORIESPart No. Description Price ea.

EQ-B26T1500 HEAVY DUTY MANUAL APPLICATOR $110.00EQ-898-1 ULTRA DRIVE MANUAL APPLICATOR $215.00

EQ-AG400 PNEUMATIC APPLICATOR $535.00EQ-7075-2kit BATTERY POWERED APPLICATOR $860.00

MILLENNIUM PG-1 LOW-RISE PUMP GRADE Shelf Life: 12 months Yield: Approx. 6 squares per case @ 12" o.c., 1/4 "- 1/2" beads

1 case- 191 cases 192 case +Part No. Description Less than 4 Pallets 4+ Pallets

MILL-PG-FA15-04 MILLENNIUM PG-1 LOW-RISE PUMP GRADE $126.00 $118.00Instructions included in each carton.20 lbs/case -- 48 cases/pallet

(Pallet+ Quantities Ship Freight Paid)


EQ‐7075‐2kitEQ‐B26T1500 EQ‐898‐1 EQ‐AG400


25Trufast Catalog: Adhesives & Sealants & Accessories

ADHESIVES, SEALANTS AND ACCESSSORIESMILLENNIUM PG-1 Pump Grade Insulation Adhesive Shelf Life: 12 months Yield: Approx. 20-25 squares per 10 gallon box set @ 12" o.c., 1/2" to 3/4" beads

1 set - 36 sets 37 sets +Part No. Description 1-2 Pallets 3+ Pallets

MILL-PG-IA5B-A01 MILLENNIUM PG-1 Pump Grade Insulation Adhesive $340.00 $318.75MILL-PG-IA5B-B01

Instructions included in each carton. 100 lbs / 10 gallon box set (Part A - 5 gallon Box, 50 lbs; Part B - 5 gallon Box, 50 lbs) -- 36 boxes (18 sets) per pallet

MILLENNIUM PG-1 DISPENSING ACCESSORIESPart No. Description Price ea.

MILL-EQ-CYC-1GK *ADCO Cyclone 1 by GarlockLow Pressure Single Bead Adhesive Pump Cart $5,000.00


MILL‐EQ‐CYC‐1GK

*Millennium PG-1 Pump Grade Insulation Adhesive is dispensed through the Millennium Cyclone 1 low pressure pump cart, or an approved low pressure pump cart which equally mixes Part 1 and Part 2 of the adhesive (e.g., dispensing cart for “Bag-in-Box” adhesive system), providing a quality, consistent application each time.


26 Trufast Catalog: Rooftop Drains

ROOFTOP DRAINSAluminum Retrofit Drains

Part No. Size Clamping Ring Strainer Pkg. Wt. Qty. 1 - 11 Qty. 12 - 24 Qty. 25 - 49 Qty. 50+

RD-3000-AL 3" Composite 10" Plastic 6 lbs. 107.30$ 104.10$ 100.60$ 97.90$



Available UpgradesPart No. Pkg. Wt. Price ea.

RD-10000-CI-S 7 lbs. + $17.50

RD-10000-CI-SCR 8.25 lbs. + $26.50

RD-10000-AL-SCR 4 lbs. + $40.00

Copper Retrofit Drains

Part No. Size Clamping Ring Strainer Pkg. Wt. Qty. 1 - 11 Qty. 12 - 24 Qty. 25 - 49 Qty. 50+

RD-3000-CU 3" Composite 10" Plastic 6 lbs. 108.60$ 102.10$ 97.00$ 91.70$




RD-10000-CI-S 7 lbs. + $17.50

RD-10000-CI-SCR 8.25 lbs. + $26.50

RD-10000-AL-SCR 4 lbs. + $40.00

Base Price ea.

Description

10" Cast Iron Strainer

10" Cast Iron Strainer & Clamping Ring

10" Cast Aluminum Strainer & Clamping Ring

Base Price ea.

Description


10" Cast Iron Strainer & Clamping Ring

10" Cast Aluminum Strainer & Clamping Ring

Cast IronStrainer

ClampingRing

AluminumStrainer

Cast IronStrainer

ClampingRing

AluminumStrainer

MADE INUSA


27Trufast Catalog: Rooftop Drains

ROOFTOP DRAINSPVC New Installation Drain Kit

Part No. Size Clamping Ring Strainer Pkg. Wt. Qty. 1 - 11 Qty. 12 - 24 Qty. 25+

RD-3000-PVC 3" Composite 10" Plastic 8 lbs. 82.80$ 78.60$ 67.30$




RD-10000-CI-S 7 lbs. + $17.50

RD-10000-AL-S 2 lbs. + $25.80

RD-12000-CI-S 11 lbs. + $26.50

Cast Iron New Installation Drain Kit

Part No. Size Clamping Ring Strainer Pkg. Wt. Qty. 1 - 11 Qty. 12 - 24 Qty. 25+

RD-3000-CI 3" Cast Itron 10" Cast Iron 14 lbs. 106.50$ 101.40$ 86.70$

RD-4000-CI 4" Cast Iron 10" Cast Iron 16 lbs. 109.50$ 103.90$ 87.70$

RD-6000-CI 6" Cast Iron 10" Cast Iron 32 lbs. 145.10$ 137.90$ 130.70$


RD-10000-AL-S 2 lbs. + $25.80

RD-12000-CI-S 11 lbs. + $26.5012" Cast Iron Strainer


10" Cast Aluminum Strainer


Base Price ea.

Description

10" Cast Aluminum Strainer

Description

Base Price ea.

Cast IronStrainer

AluminumStrainer

MADE INUSA

Cast IronStrainer

AluminumStrainer


28 Trufast Catalog: Caddy® Rooftop Suppors

CADDY® ROOFTOP SUPPORTSCADDY® Pyramid™ EZ Series Height-Adjustable EPDM Supports

Part No. Pipe Size Height Adj. Range Pkg. Qty. Price/Ea. Price/Pkg. Wgt./Pkg.RPSE1H24 Up to 1" 1.75" - 4.12" 20 $9.95 $199.00 40.3 lbs.RPSE1H57 Up to 1" 5" - 7" 10 $11.95 $119.50 30.4 lbs.RPSE2H46 Up to 2" 4.12" - 6.12" 10 $12.95 $129.50 33.3 lbs.RPSE4H46 Up to 4" 4" - 6" 5 $19.95 $99.75 25.7 lbs.

Must order in package quantities only.

CADDY® Pyramid™ RL Series Roller-Based Thermoplastic SupportsPart No. Pipe Size Height Pkg. Qty. Price/Ea. Price/Pkg. Wgt./Pkg.

RPS360406 3" Max. Fixed, 5.5" 5 $25.18 $125.90 19.3 lbs.RPS360407 3" Max. Adjustable, 12" 5 $26.38 $131.90 21 lbs.RPS360408 6" Max. Fixed, 5.5" 5 $31.78 $158.90 26 lbs.RPS360409 6" Max. Adjustable, 16" 5 $32.98 $164.91 29.8 lbs.


RL-Series Pipe Retainer StrapsPart No. Pkg. Qty. Price/Ea. Price/Pkg. Wgt./Pkg.

RPS360412 25 $2.39 $59.85 17.5 lbs.RPS360413 25 $3.59 $89.85 30 lbs.


CADDY® Pyramid™ ST Series Strut-Based Thermoplastic SupportsPart No. Max. Load Size / Type Pkg. Qty. Price/Ea. Price/Pkg. Wgt./Pkg.

RPS360400 1,000 lbs. 4" H x 10" L / Fixed 10 $11.98 $119.80 29.5 lbs.RPS360401 1,000 lbs. 6.4" H x 10" L / Fixed 5 $14.65 $73.23 23.3 lbs.RPS360402 1,000 lbs. 12" H x 10" L / Adj. 5 $23.98 $119.90 21.5 lbs.RPS360403 1,500 lbs. 4" H x 16" L / Fixed 5 $23.38 $116.90 22 lbs.RPS360404 1,500 lbs. 6.4" H x 16" L / Fixed 5 $28.78 $143.90 35.3 lbs.RPS360405 1,500 lbs. 17" H x 16" L / Adj. 5 $29.98 $149.90 33 lbs.


CADDY® Pyramid™ Pipe & Equipment Supports (Electro-galvanized Steel with Polyethylene Base)

Part No. Static Load Size Pkg. Qty. Price/Ea. Price/Pkg. Wgt./Pkg.RPS50H4EG 50 lbs. 4" H x 10-3/8" L 10 $12.70 $127.00 15.7 lbs.RPS50H6EG 50 lbs. 6" H x 10-3/8" L 10 $15.53 $155.30 18 lbs.


CADDY® Pyramid™ Bridge AssembliesPart No. Static Load Size Pkg. Qty. Price/Pkg. Wgt./Pkg.

RPS360414 2,000 lbs. 5" H x 24" L 1 $33.00 6.2 lbs.RPS360415 2,000 lbs. 5" H x 30" L 1 $35.10 6.9 lbs.RPS360417 2,000 lbs. 5" H x 36" L 1 $40.50 7.5 lbs.RPS360418 2,000 lbs. 5" H x 42" L 1 $42.00 9.9 lbs.RPS360419 2,000 lbs. 5" H x 48" L 1 $44.10 10.5 lbs.

Pipe Size Range3" and under

3.5" to 6"

Fixed

Adjustable

Fixed

Adjustable


29Trufast Catalog: Notes

30 Trufast Catalog: Committment

100% American Made ProductsNo other roofi ng fastener company can make this claim. We’ve invested over $15 million in upgrading our manufacturing facility and equipment over the past fi ve years to provide our customers with quality, competitively-priced TRUFAST products that are manufactured here in the USA.

Product When You Need ItThe expansion of our manufacturing facility completed in December, 2011 doubled our fastener capacity! You can get TRUFAST® products when and where you need them with fi ve regional warehouse locations:

Industry Code ApprovalsIndependent testing and certifi cation assures our customers that TRUFAST fasteners have been objectively tested and conform to the highest national and international standards. TRUFAST fasteners and accessories are evaluated, recognized and listed by FM Global, Miami-Dade County Product Control, State of Florida, European Technical Approvals and NTA, Inc., providing architects, specifi ers, contractors and building code offi cials with evidence that our products meet these building code requirements.

Superior Customer ServiceWe can tell you all about our amazing customer service, but we’ll let you hear from our customers instead:

“Great supplier! From shipping and customer care to technical services and performance.” Arlington Heights, IL

“The people at TRUFAST are always quick to respond and are great to work with.” Portland, ME

“Best partner we have is TRUFAST.” Saginaw, MI

Field ServicesWe go the extra mile for you with fi eld services including in-fi eld product training and demonstrations, onsite pulltests and the support of 25 experienced fi eld reps.

Engineering and Technical ServicesThe TRUFAST Engineering & Technical Services team consists of highly experienced engineers and technicians in the fi elds of metallurgy, corrosion resistance, wind uplift testing and building code compliance. Our advanced Engineering Tech Center enables us to conduct sophisticated testing to ensure that TRUFAST fasteners are designed and manufactured to the quality and performance standards that our customers depend on. TRUFAST also actively collaborates with many of the leading manufacturers and suppliers in the commercial roofi ng and building materials industries to design and develop innovative, code-compliant fastening solutions.

Quality ProductsQuality is always our fi rst commitment. We are ISO 9001:2008 certifi ed, and our products go through rigorous quality control checks at every step in the manufacturing process – assuring you of the highest quality.

Your Satisfaction GuaranteedOur commitment to customer satisfaction is simple: we do what we say we’ll do. And if there’s ever a concern, we always make it right.

800-443-9602 TRUFAST.COM

› Bryan, Ohio › Fort Worth, Texas › Jacksonville, Florida

› St. Paul, Minnesota › Ontario, California

Form No. TF-1203

TF_CommitmentSheet.indd 1 5/7/12 10:59 AM

31Trufast Catalog: Back Page

32 Caddy Pyramid: Rooftop Support System

CADDY ® PYRAMIDRooftop Support System

TRUFAST.com | 800-443-9602

DISTRIBUTED BY:

33Caddy Pyramid: Rooftop Support System

2 www.erico.com

?Why Buy

CADDY®

PYRAMID

Challenge:• Properly support heavy loads

• Minimize the chance of point loading or abrading the roof membrane

• Ensure chemical compatibility with anything you place on the roof membrane

CADDY PYRAMID Solution:• CADDY PYRAMID offers a broad portfolio compatible with

most roof surfaces, including single-ply, bituminous, metal and spray foam

• CADDY PYRAMID provides excellent load distribution with some of the industry’s best load ratings

• CADDY PYRAMID minimizes point loading and roof abrasion

• CADDY PYRAMID is UV stable, corrosion resistant, and durable over an extensive temperature range

For Engineers and Consultants:

Plumbing & HVAC Applications

Electrical Applications


?Why Buy

CADDY®

PYRAMID

Challenge:• Roofs not only protect some of the most valuable assets,

they often represent a significant cost to replace and maintain

• Substandard materials and methods can increase the chance of roof damage

• Increasingly, roofs are seen as prime real estate and are being utilized for equipment placement, alternative energy systems, and as green space

CADDY PYRAMID Solution:• CADDY PYRAMID is extremely roof compatible

• CADDY PYRAMID is designed to minimize the chance of damage to roofs

• CADDY PYRAMID is fast and easy to install, minimizing costs

• CADDY PYRAMID provides an aesthetically pleasing, flexible engineered solution designed to meet the challenges of densely populated roofs

For Building Owners: ?Why Buy

CADDY®

PYRAMID

Challenge:• Meet the project scope and stay within budget

• Provide a high quality installation

• Need a fast and easy to install solution

• Adapt to a broad range of applications and roof materials

CADDY PYRAMID Solution:• CADDY PYRAMID is designed to get installers on

and off the roof quickly

• CADDY PYRAMID creates an aesthetically pleasing, high quality solution

• CADDY PYRAMID offers a broad portfolio of solutions that simplify material management

For Contractors and Installers:

Plumbing & HVAC Applications

Equipment Support Applications

www.erico.com 3


Foam bottom offers low abrasion interface for better roof membrane protection

Hot-dip galvanized for superior corrosion protection

UV stabilized for long lasting performance

Compatible with roof surfaces including single ply, bituminous, metal and spray foam

4

CADDY® PYRAMID rooftop supports are a surface mounted solution for supporting electrical and mechanical applications on a variety of roof surfaces.

They offer superior load capacity and dramatically reduce installation time by replacing slow, heavy and labor-intensive methods for support of pipe, conduit, duct, cable tray and equipment.

Unlike wood blocks, CADDY PYRAMID supports are specifically designed for rooftop applications, incorporating unique materials and finishes that protect roof membranes and provide superior corrosion protection.

“Our clients’ roofs are a significant investment. Protecting

these assets requires the use of engineered solutions that can withstand the test of time,

which is why we have standardized on the CADDY® PYRAMID family of roof top supports.”

Chris Denman, Vice President and PartnerRoof Management, LLC

• Fewer supports required for the same load• Less material, less labor

CADDY® Q

uality

and Innovatio

ns

Load

Rating

• More than 14 years of designing and building high-quality rooftop support solutions

• Continuously innovating for over 110 years

Foam

Bottom

• Provides roof membrane compatibility• Eliminates the need for a separation sheet

Load

Distrib

ution • Minimizes point loading and stress concentrations

• Reduces likelihood of roof membrane damage

www.erico.com


5

115 lbs 350 lbs 500 lbs 570 lbs 770 lbs 1000 lbs

ProductP X

ProductBF X X

ProductBL X X X

Wood4 x 4 X X X

ProductRB X X X X

ProductM X X X X X

Rooftop Supports: Load Distribution

psi

0

2

4

6

8

10

12

14

16

18

20

CADDY® PYRAMID and other alternative solutions were tested at various loads using a pressure sensitive mat. These graphics show the static load transferred to the roof membrane. There are two key findings from the tests:

1. At a given load, CADDY PYRAMID offers superior load distribution to many alternatives

2. CADDY PYRAMID covers a broader range of load ratings than many alternatives

The takeaway: CADDY PYRAMID is a superior rooftop support solution.

Product does not support load ratings at this levelX

www.erico.com


6

CADDY® PYRAMID ST Strut-Based Supports

CADDY® PYRAMID ST Strut-Based Supports offer an ideal solution for mounting electrical and mechanical applications to strut. Superior load distribution and a low abrasion foam interface combine to ensure that the roof membrane is protected despite varying roof surfaces and shifting caused by expansion and contraction.

CADDY® PYRAMID ST Fixed Strut Supports Provides a fixed-height mounting platform with 6”, 10”, or 16” of usable strut length.

• Provides superior support for pipe, conduit, duct, cable tray and equipment

• Multiple sizes and load ratings offer the ability to tailor the solution to the application

• Easy to transport to the roof

Part Number Strut Length Height Static Load

PSF6C 6” 4.8” 300 lb

PSF10C 10” 4.8” 1,000 lb

PSF10D 10” 6.4” 1,000 lb

PSF16C 16” 4.8” 1,500 lb

PSF16D 16” 6.4” 1,500 lb

Material: Polyethylene, Polypropylene, Steel Finish: Hot-dip galvanized Temperature: -50 to 150 °F Static Load Safety Factor: 3:1

• Provides superior load distribution, even with varying rooftop surfaces

• Ready to use out of the box, saving installation time and labor

• Compatible with roof surfaces including single ply, bituminous, metal and spray foam

• Foam bottom offers low abrasion interface for better roof membrane protection

• Hot-dip galvanized and UV stabilized for long lasting performance

• Supports green building requirements; thermoplastic bases are made from recycled material and can contribute to earning LEED credits

www.erico.com


7

Also Available:

CADDY® PYRAMID ST Adjustable Strut Supports Allows elevation changes of up to 18” off the roof surface with 10” or 16” of usable strut length.

CADDY® PYRAMID ST Bridge Assemblies Provides a fixed-height mounting platform off the roof surface with 24” to 60” of usable strut length.

• Height adjustability provides effective navigation of pipe, conduit, duct and cable tray around obstructions


• Ideal for supporting multiple pipe runs, cable tray and air handling units




PSA10CH13 10” 6” – 13” 1,000 lb

PSA16AH18 16” 7” – 18” 1,500 lb


Static loads are assumed to be uniformly distributed.


PSB24A 24” 5.6” 2,000 lb

PSB30A 30” 5.6” 2,000 lb

PSB36A 36” 5.6” 2,000 lb

PSB42A 42” 5.6” 3,000 lb

PSB48A 48” 5.6” 3,000 lb

PSB60A 60” 5.6” 3,000 lb

CADDY® PYRAMID ST Strut-Based Supports

CADDY® PYRAMID 50 Foam-Based Support

• Replaces slow and labor-intensive installation methods

• Supports pipe, conduit, cable tray and equipment on roofs and below raised floors

• Easily increase load capacity by combining similar CADDY® PYRAMID supports

• Protects the roof membrane while absorbing shock and vibration, without absorbing water

• Metal cover protects against weather and other environmental conditions, such as bird damage

Material: Polyethylene, Polypropylene, Steel Static Load Safety Factor: 3:1

Part Number Length Height Static Load

Finish: Electro-galvanized

RPS50H4EG 10 3/8” 4” 50 lb

RPS50H6EG 10 3/8” 6” 50 lb

Finish: Hot-dip galvanized

RPS50H4HD 10 3/8” 4” 50 lb

RPS50H6HD 10 3/8” 6” 50 lb

“We have

standardized on CADDY PYRAMID ST Series

Supports for our cable tray installations. They are extremely

simple to use and provide a lower total installed cost

than wood blocks, concrete slabs, and other engineered solutions.”

Alain Lemaire, Achats et Réalisation | G2EI

For more information about any part please visit our website by entering:

http://www.erico.com/part.asp?part= part number

e.g: http://www.erico.com/part.asp?part=PSA16AH18

TIP

www.erico.com


8

CADDY® PYRAMID RL Roller-Based Supports

CADDY® PYRAMID RL Roller-Based Supports offer an ideal solution for mechanical piping systems. Long-lasting performance is ensured by providing polymeric rollers for corrosion free rotation. CADDY PYRAMID RL Roller-Based Supports are specially designed to avoid formation of flat spots and seized rollers during expansion and contraction. Superior load distribution and a low abrasion foam interface combine to ensure that the roof membrane is protected despite uneven roof surfaces and shifting caused by expansion and contraction.

CADDY® PYRAMID RL Fixed Roller Supports

Provides a fixed height roller to support up to 6” schedule 40 nominal pipe.

• Roller-based support designed specifically for rooftop applications

• Roller capability allows longitudinal movement of pipe, resulting from thermal expansion or contraction

Part Number Pipe Size Height Static Load

PRF2 2” Max 5.80” 100 lb

PRF3 3” Max 6.25” 250 lb

PRF6 6” Max 6.25” 600 lb


• Polymeric rollers ensure corrosion free rotation



• Ready to use out of the box, saving installation time and labor



CADDY® PYRAMID RL Adjustable Roller Supports

Adjustable height allows elevation changes up to 16” off the roof for up to 6” schedule 40 nominal pipe.

• Height-adjustable roller-based support designed specifically for rooftop applications

• Height adjustability allows for effective navigation of pipe around obstructions

Part Number Pipe Size Height Static Load

PRA3H12 3” Max 6” - 12” 250 lb

PRA6H16 6” Max 6 1/2” - 16” 600 lb


Retainer Strap Provides additional support to ensure that the pipe stays in-line with the roller.

• Prevents pipe from being dislodged from roller supports

• Innovative twist-lock design allows for easy installation without requiring hardware removal

Part Number Pipe Size

PRS2 2” Max

PRS3 3” Max

PRS6 6” Max

Material: Steel Finish: Hot-dip galvanized

Support Accessory:

www.erico.com


9

CADDY® PYRAMID H-Frame

CADDY® PYRAMID H-Frame Series Support System is a fast and economical solution for a variety of rooftop applications where support height and width exceed those of the CADDY PYRAMID ST or CADDY PYRAMID RL series. It provides an ideal support solution for duct, large diameter pipe or cable tray. Superior load distribution and a low abrasion foam interface combine to ensure that the roof membrane is protected despite varying roof surfaces and shifting caused by expansion and contraction.

CADDY® PYRAMID H-Frame Post Base

• Mounting hardware pre-installed in bases


• Foam or rubber bottom offers low abrasion interface for better roof membrane protection



• Rubber rooftop interface ideal for solar panel array installations


• Accepts standard strut channels


CADDY® PYRAMID H-Frame Kit

• Kit includes 2 post bases with pre-installed mounting hardware, 6 bolts, 6 strut nuts, and 2 L-brackets to complete H-frame

Material: Polyethylene, Polypropylene Temperature: -30 to 130 °F Static Load Safety Factor: 3:1

Part Number

RooftopInterface

Strut Type Height Length /

WidthStatic Load

PHB Foam A 4.60” 12 3/8” 750 lb

PHBR Rubber A 4.66” 12 3/8” 750 lb

Part Number

RooftopInterface

Strut Type Height Length /

WidthStatic Load

PHK Foam A 4.60” 12 3/8” 1,500 lb

PHKR Rubber A 4.66” 12 3/8” 1,500 lb

Static load represents 750 lb (3,335 N) per post base. The end user must select and evaluate the strut framing to ensure the assembled H-frame can properly support the applied load.

CADDY® PYRAMID H-Frame Hardware Kit

Part Number Screw Diameter

HFRMHDW M12


Support Accessory:

• Kit includes 6 bolts, 6 strut nuts, and 2 L-brackets to build custom multi-tier H-frame assemblies

www.erico.com


10

CADDY® PYRAMID Equipment Supports

CADDY® PYRAMID Equipment Support is a fast, flexible and innovative system for supporting heavy-duty mechanical services on rooftop surfaces. Superior load distribution and a low abrasion foam interface combine to ensure that the roof membrane is protected despite varying roof surfaces and shifting caused by expansion and contraction.

CADDY® PYRAMID Equipment Support Kit

Includes all post bases, hardware and framing needed for an out of the box solution to construct a 1 m or 2 m equipment support.

• Kit includes post-base assemblies, frame and equipment-support clamps

• Assembles and adjusts to size and height in minutes by one person with one tool

• Innovative crossbar and equipment-support clamps enable quick assembly

• Integral foam pad provides gentle interface for all roof types


• Assembled support can be lifted as one unit and easily relocated

• Available in 4- or 6-post base configurations

Material: Steel, Polypropylene, Polyethylene Finish: Hot-dip galvanized Temperature: -30 to 130 °F Height: 12” – 18” Length: 62 1/2”


CADDY® PYRAMID Equipment Support Post Base Individual post base with height adjustable leg 12” to 18” gives you the flexibility to create your own equipment support with strut.

• Ideal for use with strut channel type A and U-shaped brackets to create custom equipment supports

• Height adjustable

• Innovative base design evenly distributes load to help prevent damage to roof membrane

• Base is manufactured from UV-stabilized thermoplastic material

Material: Steel, Polypropylene, Polyethylene Finish: Hot-dip galvanized Temperature: -30 to 130 °F Static Load Safety Factor: 3:1

CADDY® PYRAMID Equipment Support Clamp Clamp to secure heavy-duty mechanical equipment when creating a custom frame out of strut.

• Ideal for use with strut channel type A and square tube to create custom equipment supports

• Slotted design offers fast and easy installation

Part Number Strut Type

PEC A


Support Accessory:

Part Number Height Length /

WidthSurface

AreaStatic Load

PEB 12” – 18” 12” 144 in² 750 lb

Part Number

Post Base Width Surface

AreaUltimate

Static Load

PEK4B 12” x 4 pc 49 1/2” 575 in² 1,120 lb

PEK6B 12” x 6 pc 85 1/2” 862 in² 2,240 lb

Static load must be stable and uniformly distributed across frame.

main red

PMS 1795CC0 M96 Y90 K2

YOUTUBE LOGO SPECS

PRINTgradient bottom

PMS 1815CC13 M96 Y81 K54

on dark backgroundson light backgrounds

standard

no gradients

watermark

stacked logo (for sharing only)

standard

no gradients

watermark

stacked logo (for sharing only)

white

WHITEC0 M0 Y0 K0

black

BLACKC100 M100 Y100 K100

www.youtube.com/user/ERICOInternational

www.erico.com


11

CADDY® PYRAMID Equipment Supports

CADDY® PYRAMID Equipment Support Frame Extension Kit

CADDY® PYRAMID Equipment Support Height Extension

Height extension used to lift the frame up to 36” off the roof surface.

• Increases the height between the equipment support frame and roof deck

• Inserts directly into CADDY® PYRAMID Equipment Support Bases

Part Number HHeight

APost Base Heightwith Extension

WWidth

PEH31 22.38” 30” - 36” 2.36”

Material: Steel, Polypropylene, Polyethylene Finish: Hot-dip galvanized Temperature: -30 to 130 °F Height: 12” – 18” Length: 62 1/2”

Part Number

Post Base Width Surface

AreaUltimate

Static Load

PEKEF 12” x 2 pc 49 1/2” 288 in² 1,120 lb

Static load must be stable and uniformly distributed across frame.

CADDY® PYRAMID Equipment Support Frame Extension must be used in conjunction with a CADDY® PYRAMID Equipment Support Kit.

“Labor represents over 50% of the costs on our projects.

We chose to standardize on CADDY® PYRAMID Equipment Supports for our air

handling unit installations, because one person can easily assemble and locate the support unit where required on the roof. This is a very

well designed product that saves installation time & keeps me under budget.”

Ulf Engel, Dipl. –Ing. (FH) | ROKO-Klimatechnik

Material: SteelFinish: Hot-Dip Galvanized

• Allows creation of custom equipment support lengths by attaching the CADDY® PYRAMID Extension Kit in series to a CADDY PYRAMID Equipment Support Kit

• Kit includes two post-base assemblies, frame and equipment-support clamps for easy attachment to a CADDY PYRAMID Equipment Support Kit

• Square tube and cross bars provide superior load and deflection capabilities over standard strut profiles

• Assembles and adjusts to size and height in minutes by one person with one tool

• Innovative crossbar and equipment-support clamps enable quick assembly

• Integral foam pad provides gentle interface for all roof types

• Hot-dip galvanized finish provides superior corrosion protection

A

W

H

www.erico.com


12

CADDY® PYRAMID Crossovers and Walkways

The CADDY® PYRAMID Crossovers portfolio includes ladders, towers, bridges and platforms that can be combined to provide a safe and clear rooftop walkway. Individual pieces can be easily assembled to meet custom application needs. Superior load distribution and a low abrasion foam interface combine to ensure that the roof membrane is protected despite varying roof surfaces and shifting caused by expansion and contraction.

CADDY® PYRAMID Crossover Ladders, 50°

Ladders at a 50° angle ranging from two steps with a height of 20” to six steps with a height of 60”.

• Standard angle ladders provide easy changes in elevation

• CADDY® PYRAMID bases provide superior load distribution and roof membrane compatibility


Material: Aluminum, Polypropylene, Polyethylene • Aluminum construction designed to withstand harsh environments

• Walking surfaces with serrated tread provides maximum slip resistance and drainage

• Modular design allows for easily configurable heights and lengths to address varying applications

• Stairs, platform and ladders are easily assembled yielding labor-saving, quick installations and level adjustments

• Interchangeable standard components for flexibility while providing safe access over piping, duct, equipment or other utilities on a roof surface

• Compliant with OSHA, Cal/OSHA and ANSI® standards

CADDY® PYRAMID Crossover Ladders, 90°

Ladders at a 90° angle ranging in height from 20” to 60”.

• Vertical Ladders ideal for tight spaces



Material: Aluminum, Polypropylene, Polyethylene

Part Number Height Width Depth Step

Height

PCL50S2 62” 52.4” 22.9” 10”

PCL50S3 72” 52.4” 36.1” 10”

PCL50S4 82” 52.4” 44.5” 10”

PCL50S5 92” 52.4” 52.9” 10”

PCL50S6 102” 52.4” 61.3” 10”

Part Number Height Width Depth Step

Height

PCL90S2 62” 52.4” 3” 12”

PCL90S3 72” 52.4” 3” 12”

PCL90S4 82” 52.4” 3” 12”

PCL90S5 92” 52.4” 3” 12”

PCL90S6 102” 52.4” 3” 12”

“Our projects often require the installation of

crossovers, walkways, and platforms to allow for easy and safe access across and over varying roof top structures. We have standardized

on the CADDY® PYRAMID family because they are engineered to be sturdy and durable but are

also extremely simple to install.”

Tyler Doyle, Project ManagerEnvironmental Roofing and Waterproofing

www.erico.com


13

CADDY® PYRAMID Crossovers and Walkways

CADDY® PYRAMID Crossover Support Towers

Supports for walkway systems ranging in height from 20” to 60”.

• Additional support towers ideal for supporting long walkways at varying heights




Part Number Height Width Depth

PCT20 40” 52.9” 2”

PCT30 50” 52.9” 2”

PCT40 60” 52.9” 2”

PCT50 70” 52.9” 2”

PCT60 80” 52.9” 2”

CADDY® PYRAMID Crossover Bridge

Bridge span with handrails connects easily in series and to CADDY PYRAMID® Crossover Ladders to provide an effective walkway.

• Standard bridge spans that can be combined to create custom pathway lengths

Material: Aluminum

Part Number Height Width Length

PCB36 44” 42” 40”

CADDY® PYRAMID Crossover Bridge Turn Kit

Provides supports, pathway and handrails to make a 90° turn at heights ranging from 20” to 60”.

• Turn bridges allow for configurations beyond a straight pathway, “L”, “U” or “Z” pathways can be created by using turn bridges





PCB36H20 62” 52.5” 47.1”

PCB36H30 72” 52.5” 47.1”

PCB36H40 82” 52.5” 47.1”

PCB36H50 92” 52.5” 47.1”

PCB36H60 102” 52.5” 47.1”

CADDY® PYRAMID Guardrail Kit

Provides extra handrails for creating custom configurations.

• Use an extra guardrail kit to block off the end of a pathway or create custom pathway configurations while ensuring all safety criteria are metMaterial: Aluminum

Part Number Length

PCGK 42”

CADDY® PYRAMID Crossover Platform

Provides four height adjustable legs and the ability to interlock sections for customizability.

• Height adjustable interlocking platforms allow for quick and easy installation of a custom pathway across rooftop surfaces

• Protect roof surfaces by providing a clearly defined pathway



PCP36 11” – 14” 36” 36”

www.erico.com


14

“As a roofing membrane manufacturer, the products that

we choose for our own roof must reflect the same level of

quality and durability as our brand. We chose the

CADDY® PYRAMID EZ Series Rooftop Support System during

our office roof renovation to replace the original wood

blocks that held up the gas lines. They were economical, simple

to install, and contributed to the general aesthetics of the roof. Just like our installing contractor said, ‘These CADDY® Supports

are pretty sweet!’”

Jerry Beall, Product and Technical Specialist FiberTite Roofing Systems, Seaman Corporation

• Quick height adjustment accommodates for uneven roofs or sloped condensate lines

• No tools or fasteners needed; fast snap-on installation

• Design sheds water and helps reduce pipe corrosion

• Roof-friendly; made of UV-stabilized EPDM material

Material: EPDM-SBR rubber

Ultimate load at 1/4” (6.35 mm) deflection. Contact project or roofing engineer for maximum allowable load on individual project roof system.

Part Number Rigid Conduit/Pipe Size Height Ultimate

Static Load

RPSE1H24 1” 1 3/4” – 4” 170 lb

RPSE1H57 1” 5” – 7” 170 lb

RPSE2H46 2” 4” – 6” 250 lb

RPSE4H46 4” 4” – 6” 400 lb

Feature a wide platform base design to provide reliable support and distribute load across roof surface. These versatile supports are fast and easy to install compared to wood blocks and metal straps.

CADDY® PYRAMID EZ Rubber-Based Supports

www.erico.com


15

ANSI is a registered trademark of American National Standards Institute. YouTube is a registered trademark of Google Inc.

WARNING ERICO products shall be installed and used only as indicated in ERICO’s product instruction sheets and training materials. Instruction sheets are available at www.erico.com and from your ERICO customer service representative. Improper installation, misuse, misapplication or other failure to completely follow ERICO’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death.

WARRANTY ERICO products are warranted to be free from defects in material and workmanship at the time of shipment. NO OTHER WARRANTY, WHETHER EXPRESS OR IMPLIED (INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), SHALL EXIST IN CONNECTION WITH THE SALE OR USE OF ANY ERICO PRODUCTS. Claims for errors, short-ages, defects or nonconformities ascertainable upon inspection must be made in writing within 5 days after Buyer’s receipt of products. All other claims must be made in writing to ERICO within 6 months from the date of shipment or transport. Products claimed to be nonconforming or defective must, upon ERICO’s prior written approval in accordance with its standard terms and procedures governing returns, promptly be returned to ERICO for inspection. Claims not made as provided above and within the applicable time period will be barred. ERICO shall in no event be responsible if the products have not been stored or used in accordance with its specifications and recommended procedures. ERICO will, at its option, either repair or replace nonconforming or defective products for which it is responsible or return the purchase price to the Buyer. THE FOREGOING STATES BUYER’S EXCLUSIVE REMEDY FOR ANY BREACH OF ERICO WARRANTY AND FOR ANY CLAIM, WHETHER SOUNDING IN CONTRACT, TORT OR NEGLIGENCE, FOR LOSS OR INJURY CAUSED BY THE SALE OR USE OF ANY PRODUCT.

LIMITATION OF LIABILITY ERICO excludes all liability except such liability that is directly attributable to the willful or gross negligence of ERICO’s employees. Should ERICO be held liable its liability shall in no event exceed the total purchase price under the contract. ERICO SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS OF BUSINESS OR PROFITS, DOWNTIME OR DELAY, LABOR, REPAIR OR MATERIAL COSTS OR ANY SIMILAR OR DISSIMILAR CONSEQUENTIAL LOSS OR DAMAGE INCURRED BY BUYER.

Copyright © 2014 ERICO International Corporation. All rights reserved. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.

CADDY® PYRAMID Universal Support

Part Number Length Width Height Thread

SizeUltimate

Static Load

PBU6 8” 6” 4” (3) 3/8”-16 300

PBU10 12 1/2” 8” 4” (2) 3/8”-16 1,000

PBU16 19” 8” 4” (2) 3/8”-16 1,500

• Captive stainless steel nuts allow for custom attachment methods to the support base including easy attachment of stainless steel strut, threaded rod or other project-specific hardware





• Base is manufactured from UV-stabilized thermoplastic material


Material: Polyethylene; Polypropylene; Stainless Steel 18-8Temperature : -50 to 150 °FStatic Load Safety Factor: 3:1

• Lightweight plastic construction

• UV resistant, designed and tested for outdoor use

• No tools or fasteners needed for installation

• Rounded edges to help protect the roof membrane

Material: Acrylonitrile Butadiene Styrene

Part Number Height Static Load

PPRPS25H4 3 5/8” 25 lb

PPRPS25H6 5 5/8” 25 lb

CADDY® PYRAMID 25 Pipe and Conduit Support

“The CADDY PYRAMID family allows us to streamline our

project operations while delivering an aesthetically pleasing

product for our clients.”

Kyle Laubach, VP of OperationsEnvironmental Roofing and Waterproofing

www.erico.com


48 Dow® Tile Bond™ Roof Tile Adhesive

TILE BOND™ Roof Tile AdhesiveStrength on any job.

Through the years, there have been many choices for installing concrete and clay roof tiles. And for the most part, none of them have been ideal … until now. TILE BOND™ Roof Tile Adhesive from Dow is a superior solution for installing roof tile. Not only does it go on fast — it stays strong, even in harsh environments where hurricanes, high winds and temperature extremes put adhesive-applied systems to the test.

Tiles go on fast and easy.TILE BOND™ Roof Tile Adhesive can work on a variety of roof tile jobs, including most low/flat, medium, high and two-piece barrel (cap and pan) profiles. TILE BOND™ works in both new and reroof applications. And it’s ideal for patch and repair — as well as for specialty applications such as ridge, rake, valley and hip installations.

TILE BOND™ is a single-component polyurethane adhesive that eliminates the problems typically found with other attachment methods like mortar, screws, wire ties and two-component foam systems. There’s no equipment to calibrate (as you find in two-component products). With TILE BOND™, you just open the valve and you’re ready to go.

Convenience and simplicity.TILE BOND™ Roof Tile Adhesive comes in two convenient sizes. The 23 lb. container of TILE BOND™ is ideal for larger jobs and will adhere up to 575 field tiles at 1.5” x 1” x 4” (paddies). A dispenser is included with each canister that helps you apply it quickly and accurately. The 28 oz. can of TILE BOND™ is ideal for small jobs and repairs and will adhere up to 40 tiles at 1.5” x 1” x 4” (paddies). Tiles should be set within adhesive pad within 4 minutes of dispensing adhesive.*

Theoretical yield: High-profile tile, 4–6 squares; medium-profile tile, 6–8 squares; low-profile tile, 8–10 squares.†

TILE BOND™

— Miami-Dade County approved

— Florida Building Code approved

— Hurricane-zone qualified

— No off-ratio concerns

— No equipment or capital needed

— No external power required

— No cleanup or equipment maintenance

— Up to 575 field tiles per 23 lb. tank

— Zero Ozone-Depletion Potential

* High temperature and humidity will accelerate the curing process.† Theoretical yields may differ from actual usage, and environmental

conditions may vary the actual in-place yields.

Photo courtesy of Eagle Roofing Products

United States | C O M M E R C I A L / R E S I D E N T I A L

49Dow® Tile Bond™ Roof Tile Adhesive

In the U.S.The Dow Chemical CompanyDow Building Solutions200 Larkin Center, 1605 Joseph DriveMidland, MI 48674

** Acceptance No. 11-0616.03. Expires: 8/23/16. Florida Building Code FL #717, see Revision 4.

Notice: No freedom from infringement of any patent owned by Dow or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for determining whether products and the information in this document are appropriate for Customer’s use and for ensuring that Customer’s workplace and disposal practices are in compliance with applicable laws and other government enactments. The product shown in this literature may not be available for sale and/or available in all geographies where Dow is represented. The claims made may not have been approved for use in all countries. Dow assumes no obligation or liability for the information in this document. References to “Dow” or the “Company” mean the Dow legal entity selling the products to Customer unless otherwise expressly noted. NO WARRANTIES ARE GIVEN; ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.

CAUTION: When cured, these products are combustible and will burn if exposed to open flame or sparks from high-energy sources. Do not expose to temperatures above 240ºF (116ºC). For more information, consult Material Safety Data Sheet (MSDS), call Dow at 1-866-583-BLUE (2583) or contact your local building inspector. In an emergency, call 1-989-636-4400 in the United States or 1-519-339-3711 in Canada.

TILE BOND™ adhesive products contain isocyanate and a hydrofluorocarbon blowing agent. Read the label and MSDS carefully before use. Wear long sleeves, gloves, and goggles or safety glasses. Provide adequate ventilation or wear proper respiratory protection. Contents under pressure.

Building and/or construction practices unrelated to building materials could greatly affect moisture and the potential for mold formation. No material supplier, including Dow, can give assurance that mold will not develop in any specific system.

Printed in the U.S.A. ®TM* Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow Form No. 179-05054-0514 CDP CDP 46703

Sales and Technical Information 1-866-583-BLUE (2583)

tilebond.comdowadhesives.com

Low/Flat Tile Profile

Medium Tile Profile

High Tile Profile

Two-Piece Barrel Tile Profile

Note: TILE BOND™ paddy placement in photographs is for reference only.

The superior solution.TILE BOND™ Roof Tile Adhesive gives contractors a welcome alternative to traditional attachment methods. Screws puncture waterproof membranes and the roof deck, leading to leaks. Mortar is heavy, labor-intensive and subject to the effects of freeze-thaw cycles. And two-component systems represent a considerable investment of money while requiring continual monitoring of ratios.

By contrast, TILE BOND™ requires no equipment to apply and protects tiles and other components far better than other methods — while maintaining exceptional adhesive qualities in the harshest weather.

Why we aren’t afraid of hurricanes.TILE BOND™ Roof Tile Adhesive is Miami-Dade County approved** and hurricane-zone qualified. TILE BOND™ is approved for use in applications that are Miami-Dade County approved and meet HVHZ requirements.

Strength on any job.Whatever the application, you can be assured TILE BOND™ Roof Tile Adhesive will get the job done. For more information about TILE BOND™ or any other Dow product, call 1-866-583-BLUE (2583) or visit us at tilebond.com

High quality tile installation calls for high performance components such as TILE BOND™. The strong, yet workable, initial adhesion helps my crew complete jobs quickly and precisely, and the ready-to-use kit ensures quality, on-ratio adhesive in a simple, portable and maintenance free system.

Israel JimenezIndependent Roof Tile Installation Specialist,Clearwater, FL

“

”

50 Firestone: I.S.O. Twin Pack™ Insulation Adhesive

TECHNICAL INFORMATION SHEET

ISO 9000 ID No.: S723-PRD-061

8121/05

I.S.O. Twin Pack™ Insulation Adhesive

Firestone Item Number: W56RACINTA DESCRIPTION: I.S.O. Twin Pack Insulation Adhesive is a two-component low-rise polyurethane adhesive designed for anchoring acceptable roof insulation to specific deck types where allowed by Firestone specifications. I.S.O. Twin Pack Insulation Adhesive is dispensed using I.S.O. Twin Pack Hand Dispenser (Firestone Item No.: W56RACINTG) or I.S.O. Twin Pack Four Bead dispenser (Firestone Item No.: W56RACINT4). The dispensers extrude I.S.O. Twin Pack Part A and B simultaneously to the static mixer, which results in mixed adhesive in bead form.

AVAILABLE WARRANTIES: Firestone Building Products standard warranties are available up to 20-year warranty period. APPLICATION: Install I.S.O. Twin Pack Insulation Adhesive only when ambient conditions, and bonding substrates and insulations, exceed 35° F (2° C) and are rising. To mix and dispense I.S.O. Twin Pack Insulation Adhesive from kits, apply the static mixer over plug end of kit by hand tightening static mixer to kit with plug end facing up. Keep plug end facing up until you are ready to dispense I.S.O. Twin Pack Insulation Adhesive to the deck substrate. Properly mixed I.S.O. Twin Pack will be yellow, with no marbling. Part A and B will be extruded simultaneously through dispensing equipment. To stop dispensing I.S.O. Twin Pack Insulation Adhesive, stop the dispenser plunger from advancing and point the mixing end up to stop Part A and Part B from entering static mixer. This stopped position of the kit can only be maintained for several minutes, as Part A and Part B already in the static mixer will continue to react, set up, and block the static mixer. If the static mixer becomes blocked during stopped period, replace static mixer in order to mix and dispense the remaining Part A and Part B in kit. Apply I.S.O. Twin Pack Insulation Adhesive in a bead 1/2” (12.7 mm) wide to deck substrate in spacing as specified for the project. The adhesive will rise (to a bead of 3/4” – 1” (19.0 mm – 25.4 mm)) within minutes after placement. Rise time will depend on the ambient conditions: warmer=faster; cooler=slower. To insure that the insulation makes continuous contact with the adhesive during the critical set-up period, set the insulation board [(4’ x 4’ (1.22 m x 1.22 m)] maximum) in fresh I.S.O. Twin Pack insulation adhesive before a skim coat develops. Immediately after setting each insulation board, weight each board using full pails of Bonding Adhesive or other available source of weight that will not damage the roof insulation.

PRODUCT DATA Composition, Part A: Isocyanate pre-polymer Composition, Part B: Polyol Mix Ratio of A:B: 1:1 by volume Color, Part A: Amber Color, Part B: Off-white Specific Gravity, Part A: 1.18 + 0.06 Specific Gravity, Part B: 1.02 + 0.05 Viscosity, Part A or B: 16,000-32,000 CPS, #5 spindle @ 5

RPM, 77° F (VOC) Volatile Organic Compound Content: 0 grams/liter COVERAGE RATE: Each I.S.O. Twin Pack kit, when properly mixed, dispenses 150 feet (45.7 meters) of mixed adhesive in a bead 1/2” (12.7 mm) wide. This bead will rise to 3/4” - 1” (19.0 mm - 25.4 mm). This equates to 600 sq. ft. (55.74 sq. m) per carton when installed in beads 12” (0.3048 m) on center (typical spacing). Coverage rate may be reduced due to irregularities in substrates. Coverage rates for other bead spacing: 6” (152.4 mm) on center: 300 sq. ft. (27.87 sq. m)/CTN 4” (101.6 mm) on center 200 sq. ft. (18.58 sq. m)/CTN PACKAGING: I.S.O. Twin Pack Insulation Adhesive is packaged: four 750 ml Part A and B kits, eight static mixers, and one instruction sheet per carton. TYPICAL SET-UP TIMES: At 60° F (15.6° C) to 90° F (32.2° C): approx. 5-8 minutes At 35° F (2° C) to 60° F (15.6° C): approx. 8-15 minutes SHELF LIFE: When I.S.O. Twin Pack is stored in original unopened container.indoors away from direct sunlight between 60° F (15.6° C) and 80° F (26.7° C), shelf life is twelve months. Store cartons with kits on their side. DO NOT store kits with plunger or plugged end down to avoid the possibility of leakage.

51Firestone: I.S.O. Twin Pack™ Insulation Adhesive

TECHNICAL INFORMATION SHEET

ISO 9000 ID No.: S723-PRD-061

8121/05

DECK SUBSTRATE AND METHOD OF APPLICATION:

NECESSARY EQUIPMENT: Refer to Training Manual. The following equipment is necessary to dispense I.S.O. Twin Pack Insulation Adhesive:

I.S.O. Twin Pack Four Bead Dispenser Firestone Item No. W56RACINT4 (sold separately): Cart and wheel mounted, hand maneuverable, with battery driven plungers, mixes and dispenses four beads of I.S.O. Twin Pack Insulation Adhesive simultaneously 12” (0.3048 meters) on center. I.S.O. Twin Pack Four Bead Dispenser is necessary for dispensing I.S.O. Twin Pack Insulation Adhesive on open, unobstructed roof area. I.S.O. Twin Pack Hand Dispenser Firestone Item No. W56RACINTG (sold separately): Hand powered, mixes and dispenses one bead of I.S.O. Twin Pack Insulation Adhesive. I.S.O. Twin Pack Hand Dispenser is necessary for dispensing I.S.O. Twin Pack Insulation Adhesive on roof areas where Four Bead Dispenser cannot be maneuvered. Static Mixer Supplied with I.S.O. Twin Packs. Static mixer bolts on plugged end of kit (with plugs removed). As Part A and B are simultaneously extruded into the static mixer, the static mixer properly and thoroughly mixes Part A and Part B. Tip at end of static mixer (opposite bolt end) dispenses mixed I.S.O. Twin Pack Insulation Adhesive in a 1/2” (12.7 mm) wide bead. This sheet is meant only to highlight Firestone’s products and specifications. Information is subject to change without notice. Firestone takes responsibility for furnishing quality materials, which meet Firestone’s published product specification. As neither Firestone itself nor its representatives practice architecture, Firestone offers no opinion on, and expressly disclaims any responsibility for the soundness of any structure on which its products may be applied. If questions arise as to the soundness of a structure, or its ability to support a planned installation properly, the Owner should obtain opinions of competent structural engineers before proceeding. Firestone accepts no liability for any structural failure or for resultant damages, and no Firestone Representative is authorized to vary this disclaimer.

Deck/Substrate

Acceptable

Pull Test

Required

Not-

Acceptable

Notes

Steel X New steel decks may require cleaning to remove processing oils.

Structural Concrete (New) X Structural Concrete (Existing) X

New poured decks must have a minimum 28-day drying time.

Plywood and OSB X

Cementitious Wood Fiber X

Gypsum Decks X

Lightweight Concrete X

Coal Tar Pitch Built-up Roofs X Existing Asphalt and Modified Bitumen Roofs (Mineral or Smooth Surfaced)

X

Existing Single-Ply Roofs X

Base Sheets X

Insulations:

Polyiso, Wood Fiber, DensDeck Products

X

Expanded Polystyrene Extruded Polystyrene, Fiberglass, Perlite

X

Existing decks containing residual asphalt must be cleaned and scraped smooth as possible. Surfaces to receive I.S.O. Twin Pack Insulation Adhesive shall be clean, dry, sound, solid, free of oil, grease, and other contaminates. See the appropriate Firestone Design Guide for more information..

I.S.O. Twin Pack™ Insulation Adhesive

GENERAL INFORMATION: 1. At the start of each workday, perform a trial anchoring with a

sample piece of insulation with I.S.O. Twin Pack Insulation Adhesive to verify applicability for that day. Verify that proper mixing, set-up and overall adhesion of insulation to substrate is being achieved before proceeding.

2. Review applicable MSDS sheets prior to use. 3. Review dispensing equipment prior to use. Insure dispensing

equipment is in good working order. 4. Avoid contact with eyes. Wear safety glasses with side shields. 5. Avoid breathing of vapors. A Self-Contained Breathing Apparatus

(SCBA) or Respirator should be used in areas of limited ventilation.

6. Avoid contact with skin. Wear gloves when dispensing. Wash hands thoroughly after handling.

7. Personnel who are sensitive/allergic to isocyanate or polyurethane should not work with I.S.O. Twin Pack Insulation Adhesive.

8. Do not smoke during use. Protect from heat sources and sparks. 9. Do not allow I.S.O. Twin Pack to freeze. Store between 60° F

(15.6° C) and 80° F (26.7° C). Apply at 35° F (1.67° C) and rising or higher.

10. DO NOT store in direct sunlight. 11. Store kits on their sides. DO NOT store with plunger or plug end

down to avoid leakage. 12. Keep plugs on kits tightly closed during storage. DO NOT expose

to moisture. 13. Use only when conditions allow, and daily trials indicate

successful adhesion. 14. It is imperative that freshly installed insulation is continuously

weighted until I.S.O. Twin Pack Insulation Adhesive sets up and the board is held in place by the adhesive.

15. Use caution when removing plugs from kits 16. Do not burn empty kit containers. Dispose in accordance with

local, federal, and state regulations. 17. It is the responsibility of the Roofing Contractor to maintain

dispensing equipment in good working order to deliver and thoroughly mix, meter, and dispense this adhesive in ratio of 1:1 (Part A:Part B).

18. Install only as much roof insulation anchored with I.S.O. Twin Pack Insulation Adhesive as can be covered and made watertight during that working day. Performance of I.S.O. Twin Pack should be periodically monitored during the workday to verify that sufficient rise, adhesion, and mating of the insulation using I.S.O. Twin Pack is occurring.

LEED INFORMATION: Post Consumer Recycled Content: 0% Post Industrial Recycled Content: 0% Manufacturing Location: Chargrin Falls, OH

Firestone Building Products Company

A Division of BFS Diversified Products, LLC 310 E. 96th Street, Indianapolis, IN 46240

Sales: (800) 428-4442 • Technical (800) 428-4511 www.firestonebpco.com

Subject to the conditions of Approval when installed as described in the current

edition of the FM Approval Guide

52 Fomo Products: Handi Foam Spray Foam 53Fomo Products: Handi Foam Spray Foam

Handi-Foam® Quick Cure Spray Foam is a low pressure foam system that utilizes a non-flammable blowing agent. Handi-Foam Quick Cure Spray Foam has been specifically formulated for flame retardancy and conforms to the requirements of ASTM E84 as a "Class 2(B)" system (flame spread of 75 or less, smoke development of 450 or less). The foam helps to lower heating and cooling costs by drastically reducing energy consumption. Application Areas Spray foam onto any clean, dry surface in any direction to insulate, fill and seal various size voids, deaden sound or reduce vibration. It is specifically designed to spray onto flat or irregular surfaces and to fill large cavities where flame retardant requirements specify E84 Class 2 (B) Spray Foam. Properties Two-component froth foam systems will expand immediately upon chemi-cal reaction of A component (isocyanate) and B component (a polyol blend) to a final volume that is 3 to 5 times the dispensed volume, in typical appli-cations, depending on various factors such as cavity size and ambient conditions. The foam will cure to a semi-rigid closed cell foam. Handi-Foam Quick Cure Spray Foam fully expands and dries tack-free within 30-60 seconds, is cuttable in 2-5 minutes and fully cures within 1 hour. Handi-Foam Quick Cure Spray Foam adheres to almost all building materials with the exception of surfaces such as polyethylene, Teflon®, polypropylene, silicone, oils, greases, mold release agents and similar materials. Optimum application temperature is 75°F (24°C) to 85°F (29°C) but may be sprayed onto colder or warmer substrates, with slight effects on the foam characteristics. Cured foam is resistant to heat and cold, -200°F to +240°F (-129°C to +116°C), and to aging, but not UV rays (i.e. sunlight) unless painted, covered or coated. Cured polyurethane foam is chemically inert and non-reactive in approved applications, and will not harm electrical wire insulations, Romex®, rubber, PVC, polyethylene (i.e. PEX) or other plastic. It is approved for use around wires, plumbing penetrations, etc. Handi-Foam Quick Cure Spray Foam systems are available in three non-refillable sizes to meet specific job applications requirements. When sprayed, the foam will create a seamless, continuous seal to insulate and protect against dust, air infiltration and pests. Physical Properties See technical data table on the second page. Preparation For Use Substrate must be clean, dry, firm, free of loose particles and free of dust, grease and mold release agents. Protect surfaces not to be foamed. Shake kits well before using (applicable to non-refillable systems). Read the enclosed operating instructions available in every kit or they can be found on our website www.fomo.com. Carefully read all cautions and warnings before use. Always refer to the local building codes before appli-cation of product.

Use Warm tanks to 75°F-85°F (24°C-29°C). After following instructions for set-up, attach appropriate hose to tanks A and B if needed (II-605 size). Shake kits well before using. Open tank valves as directed. Materials are dis-pensed through the hoses. Attach the static cone or fan nozzle to the end of the dispensing unit. The A-component and the B-component meet and mix in the disposable nozzle. With a nozzle attached to the two-component froth dispensing unit, dispense foam by squeezing the trigger of the unit. To interrupt or stop foaming process, release the trigger. Once foaming proc-ess has stopped, the dispensing unit must be reactivated within 30 seconds or a new nozzle must be installed. Fresh foam may be applied in several stages to reduce overfilling of void or damage to non-rigid, confined cavi-ties. Cured foam can only be removed mechanically. Personal Protective Equipment (PPE): Use only in a well-ventilated area with certified respiratory protection or a powered air purifying respirator (PAPR). Wear protective glasses or gog-gles with side shields, nitrile gloves, and clothing that protects against dermal exposure. Read all instructions and safety information (MSDS) prior to use of any product. The MSDS can be found at www.fomo.com. For additional product stewardship information visit www.fomo.com/healthandsafety/default.aspx Important Note: The urethane foam produced from these ingredients will support combus-tion and may present a fire hazard if exposed to a fire or excessive heat about 240°F (116°C). KEEP OUT OF REACH OF CHILDREN. Product Storage Store in a dry area. Do not expose the kit or tanks to open flame or tem-peratures above 120°F (49°C). Excessive heat can cause premature aging of components resulting in a shorter shelf life. Handi-Foam Quick Cure Spray Foam is reusable by following product instructions. Cold Weather Note: For best results, foam chemical temperature must be between 75°F-85°F (24°C-29°C). Warm kits for a minimum of 1 day at room temperature.

Disposal Procedures Refer to product SDS (Section 13) for instructions. Always dispose of empty cylinders according to applicable federal, state, provincial and local regulations. Check with your local waste disposal service for guidance. Warranted shelf life is twelve (12) months from date of manufacture.

2775 Barber Road PO Box 1078 Norton, Ohio 44203 USA

p: 1 330.753.4585 1 800.321.5585 f: 1 330.753.5199 e: [email protected] w: www.fomo.com

A16130 © Fomo Products, Inc. Rev. 11/12-24

TECHNICAL DATA SHEET

Two-Component Quick Cure Spray Foam

FOR PROFESSIONAL USE ONLY

E-84 Class 1 (Metric data shown in parentheses)

DENSITY ASTM D-1622

1.75 lb/ft3 (28 kg/m3)

K-FACTOR ASTM C-518 - aged 28 day value

0.162 BTU·inch / ft²·h·°F (0.023 W/m·K)

R-VALUE (Metric RSI in parentheses)

6.2 / inch (RSI=1.09 / inch, 0.043 / mm)

AIR BARRIER PROPERTIES ASTM E-283 @1.57 psf (75 Pa) @6.24 psf (300 Pa)

<0.01 cfm/ft² (<0.05 L/s/m²) <0.01 cfm/ft² (<0.05 L/s/m²)

PERM RATING ASTM E-96 1" (2.54 cm) 3" (7.62 cm)

2.61 (149.3 ng/(m²·Pa·s)) 1.26 (72.1 ng/(m²·Pa·s))

TENSILE STRENGTH ASTM D-1623 Parallel @ 7%

45 psi (310 kPa) COMPRESSIVE STRENGTH ASTM D-1621 Parallel @ 10% Perpendicular @ 10%

23 psi (158 kPa) 16 psi (110 kPa)

DIMENSIONAL STABILITY ASTM D-2126 HEAT AGE: +158°F (70C) HUMID AGE: +158°F (70ºC), 100%

RH COLD AGE: -4°F (-20C)

-0.6% +2.9% -0.3%

CLOSED CELL CONTENT ASTM D-2856

>90%

TACK-FREE / EXPANSION TIME

30 - 45 seconds

CUTTABLE 2-5 minutes

FULLY CURED 1 hour FIRE RATING ASTM E-84

Flame Spread Index = 25 Smoke Developed =200

DENSITY ASTM D1622 Free Rise

1.75 lb/ft3 (28 kg/m3)

K-FACTOR ASTM C518 Aged 90 days at 140°F (60°C)

0.166 BTU·inch / ft²·h·°F (0.023 W/m·K)

R-VALUE (Metric RSI in parentheses) Aged 90 days at 140°F (60°C) 6.0/inch (RSI=1.05/inch)

AIR BARRIER PROPERTIES ASTM E283 Tested at 1" thickness @1.57 psf (75 Pa)

0.003 cfm/ft² (0.02 L/s/m²)

PERM RATING ASTM E96-Method A 1" (2.54 cm) 2.5" (7.62 cm)

1.99 (119 ng/(m²·Pa·s))- Class III Vapor Retarder 1.18 (71 ng/(m²·Pa·s))- Class III Vapor Retarder

TENSILE STRENGTH ASTM D1623

29 lbf/in² (200 kPa)

AIR PERMEANCE ASTM E2178 .02 l/(m²·s)

COMPRESSIVE STRENGTH ASTM D1621 Parallel @ 10% Perpendicular @ 10%

27 lbf/in² (186 kPa) 18 lbf/in² (124 kPa)

DIMENSIONAL STABILITY ASTM D2126 HEAT AGE: +158°F (70°C) HUMID AGE: +158°F (70ºC), 100% RH COLD AGE: -4°F (-20°C)

-0.6% +2.9% -0.3%

CLOSED CELL CONTENT ASTM D2856

95%

TACK-FREE / EXPANSION TIME 30 - 60 seconds

CUTTABLE 2-5 minutes

FULLY CURED 1 hour

FUNGI RESISTANCE ASTM G21 No Growth

FIRE RATING*

ASTM E84 Tested at 2" thickness (full coverage)

Flame Spread Index = 75 Smoke Developed =450

UL 94

ASTM C736

HF-1

DIN 4102.1

B2

Technical Data

* Yields are based on theoretical calculations, for comparative purposes, and will vary depending on ambient conditions and particular application.

Always read all operating, application and safety instructions before using any products. Use in conformance with all local, state and federal regulations and safety requirements. Failure to strictly adhere to any recommended procedures and reasonable safety precautions shall release Fomo Products, Inc. of all liability with respect to the materials or the use thereof. For additional information and location of your nearest distributor, call Fomo Products, Inc. 1 330.753.4585 or 1 800.321.5585. NOTE: Physical properties shown are typical and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal laboratory conditions and may vary upon use, tem-perature and ambient conditions. Right to change physical properties as a result of technical progress is reserved. This information supersedes all previously published data. Yields shown are based on theoretical calculations and will vary depending on ambient conditions and particular application. Read all product directions and safety information before use. Consult local building codes for specific requirements regarding the use of cellular plastics or urethane products in construction. WARNINGS: Follow safety precautions and wear protective equipment as recommended. Consult Material Safety Data Sheet (MSDS) at www.fomo.com for specific information. Prolonged inhalation exposure may cause respiratory irritation/sensitization and/or reduce pulmonary function in susceptible individuals. Onset may be delayed. Pre-existing respiratory conditions may be aggravated. Use only in a well ventilated area and with certified respiratory protection. NIOSH approved positive pressure supplied air respirator is recommended if exposure guidelines may be exceeded (see MSDS). Contents may be very sticky and irritating to skin and eyes, therefore wear safety glasses or goggles, nitrile gloves, and clothing that protects against dermal exposure when operat-ing. If liquid chemical comes in contact with skin, first wipe thoroughly with dry cloth, then rinse affected area with water. Wash with soap and water afterwards, and apply hand lotion if desired. If liquid comes in contact with eyes, immediately flush with large volume of clean water for at least 15 minutes and get medical help at once. If liquid is swallowed, get immediate medical attention. Do not induce vomiting. If breathing is difficult, give oxygen. If breathing has stopped give artificial respiration. Products manufactured or produced from these chemicals are organic and, therefore, combustible. Each user of any product should carefully determine whether there is a potential fire hazard associated with such product in a specific usage. KEEP OUT OF REACH OF CHILDREN. LIMITED WARRANTY: The Manufacturer warrants only that the product shall meet its specifications: THIS WARRANTY IS IN LIEU OF ALL WRITTEN OR UNWRITTEN, EXPRESSED OR IMPLIED WARRANTIES AND THE MANUFACTURER EXPRESSLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. The buyer assumes all risks whatso-ever as to the use of the material. Buyer’s exclusive remedy as to any breach of warranty, negligence or other claim shall be limited to the replacement of the material. Failure to strictly adhere to any recom-mended procedures shall release The Manufacturer of all liability with respect to the materials or the use thereof. User of this product must determine suitability for any particular purpose, including, but not limited to, structural requirements, performance specifications and application requirements prior to installation and after product is applied.

Handi-Foam Quick Cure Spray Foam conforms to the requirements of ASTM E84 as a class 2 (B) material. Tested at two inch thickness. GREENGUARD Certification Contains a non-flammable HFC propellant. Made in Akron, Ohio

Approvals / Standards

Fomo Products, Inc. p: 1 330.753.4585, 1 800.321.5585 f: 1 330.753.5199 e: [email protected] w: www: fomo.com

A16130 © Fomo Products, Inc. 2004 Rev. 11/12-24 Page 2 of 2

Theoretical Yield* Non-Refillable Board Feet Cubic Feet

II-105 P10700 105 (9.8 m²) 8.75 (.25 m³)

II-205 P10720 205 (19 m²) 17 (.48 m³)

II-605 P10749 605 (56.2 m²) 50 (1.42 m³)

Weight (including packaging)

26.4 lbs

41 lbs

115.7 lbs

Processing Parameters Product Storage* <120°F (49°C) Store in a dry area

Application Temperature 40°F (5°C)- 120°F (49°C) For best results

Chemical Temperature 75°F (24°C)- 85°F (29°C)

* For best results, warm kit for a minimum of 1 day at 75°F (24°C)- 85°F (29°C)

Pour-in-Place Slow Rise Refillable Systems Two-Component Low Pressure E84 Quick Cure Spray Foam

The numerical flame spread rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

52 Notes 53Notes

trufast catalog 2015 - connective...

Documents