ts 100 us rev0 012910

Upload: rbucholz

Post on 02-Jun-2018

225 views

Category:

Documents


1 download

TRANSCRIPT

  • 8/10/2019 TS 100 US Rev0 012910

    1/2

    GELVA

    TS100ADHESIVETEC H N I C AL DATA SHEET

    PSAS-00038

    RE V : 029 JA N U A R Y 2010

    DESCRIPTION

    GELVA TS 100 is a vinyl acetate/acrylate copolymer emulsion supplied at 55% solids in water. Driedfilms of TS 100 are clear, will not re-emulsify in water and exhibit excellent low temperature flexibility. TS100 is used widely to formulate adhesives for non-porous, difficult to bond substrates such as glass, PVCmetal foils and a variety of plastics including low surface energy types. It also works well on poroussubstrates such as paper and wood and can be formulated to function as a heat-sealable adhesive.

    FEATURES & B ENEFITS

    Bonds to a variety of surfaces

    Films are flexible and resist re-emulsification Good low temperature performance

    Good compatibility with organic solvents andborax solution

    SUGGESTEDAPPLICATIONS

    Laminating adhesives

    Heat-activated adhesives

    Textile coating

    Composites

    Emulsion paints

    CHARACTERISTICS AND PROPERTIES

    Table 1| Physical Characteristics1

    Total Solids , % 54.5 57.5

    Viscosity @25C, cps 1,000 1,600

    (LVF #3@30 rpm)

    pH 4.5 5.0

    Density @25C, lb/gallon 8.9

    Table 2 | Other Properties1

    Particle Size Most < 1 micron

    Residual Monomer Content < 0.75%

    Dilution Stability 0.5 1.5

    Borax Stability Excellent

    Alcohol Tolerance 100ml / 100ml

    Bond Time 25 30 seconds

    Wood Shear Bond 1300 1500 psi

    Heat Seal Temperature 180 190F

    1Typical values based on samples tested. Not specifications.

  • 8/10/2019 TS 100 US Rev0 012910

    2/2

    GELVA

    TS100ADHESIVETEC H N I C AL DATA SH EET

    PSAS-00037ARE V : 0

    29 JA N U A R Y 2010

    T e s t C on di t i on s f o r O t h e r P r ope r t i e s

    Dilution Stability: Milliliters of phase separation in 100 milliliters of emulsion at 5% solids in a 100 mil

    graduated cylinder after 24 hours Borax Stability: Stability of the emulsion in a 5% borax solution

    Solvent ToleranceAlcohol: Milliliters of alcohol compatible with 100 grams of emulsion. Upper limitis noted as the point at which the emulsion is very thick

    Bond Time: Time in seconds to paper failure of a 5 mil wet film sandwiched between two pieces ofbleached sulfite paper, substance 20.

    Wood Shear Bond: ASTM D-905-49

    Heat Seal Temperature of Film: Temperature required to heat seal a 5 mil wet film cast on paper andair dried 24 hours under standard ASTM conditions

    PACK AGING

    TS 100 is available in bulk tank trucks, intermediate bulk containers (IBCs), drums and pails.

    STORAGE AND HANDL ING

    TS 100 will be stable for 6 months under normal conditions. Keep drums tightly sealed and store in a dryarea between 10 30C. Rotate stock using oldest material first. Product in its original container that isnot in specification can be returned within 6 months from date of receipt upon confirmation of the problemand of proper storage and handling.

    Handle TS 100 in accordance with good industrial hygiene and safety practices including avoidingunnecessary exposure to the product or its vapors and removal of material from skin, eyes and clothingFor additional health, safety and handling information refer to the product MSDS.

    REGULATORY STATUSMay be used in pressure sensitive adhesives applied to the outside of food packaging (paper, plastic andglass packages and bottles, and packaging closures) covered under 21 C.F.R. 175.105 (Adhesives)pursuant to the conditions and limitations set forth in that regulation. Other provisions may apply to thisproduct. For full compliance statement, please contact Cytec [email protected] .

    It is the users responsibility to conduct his/her own FDA evaluation of his/her final adhesive formulationand processing and to ensure the presence of a functional barrier between the adhesive and food, toconfirm suitability of the intended end use in indirect food contact applications, as well as to ensure thecompliance of the finished product with all prevailing legislation regulating its application.

    CONTACT INFORMATION

    Global Product Referraltel 1.800.652.6013 (USA)tel 1.973.357.3193 (Outside the USA)

    [email protected]

    DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered tobe representative of the product described. Cytec Engineered Materials (CEM) does not express or imply any guarantee or warranty of any kindincluding, but not limited to, the accuracy, the completeness or the relevance of the data and information set out herein. Because the propertiesof this product can be significantly affected by the fabrication and testing techniques employed, and since CEM does not control the conditionsunder which its products are tested and used, CEM cannot guarantee that the properties provided will be obtained with other processes andequipment. No guarantee or warranty is provided that the product is adapted for a specific use or purpose and CEM declines any liability withrespect to the use made by any third party of the data and information contained herein. CEM has the right to change any data or informationwhen deemed appropriate. All trademarks are the property of their respective owners.

    mailto:[email protected]:[email protected]:[email protected]:[email protected]