tubing and pipes - inicio · allowable working pressures are based on equations from asme b31.3 for...

Tubing, Pipes, Hoses and ConnectorsDTubing and Pipes．．．．．．．．．．．．．．．D-02

Hoses and Connectors ．．．．．．．．．．．．D-18

Tubing and Pipes

Tubing and Pipes D-02

Tubing and Pipes D-04D-03 Tubing and Pipes

Proper selection, handling, and installation of tubing, when combined with proper selection of FITOK tube fittings, are

essential for reliable tubing systems.

The following variables should be considered when ordering tubing for use with tube fittings:

Surface finish

Material

Hardness

Wall thickness

FITOK

◎

◎

◎

◎

Tubing Selection

It is important to properly handle the tubing in order to reduce the scratches and protect the surface finish.

Tubing should never be dragged out of a tubing rack or across a rough surface.

Tube cutters or hacksaws should be sharp. Do not take deep cuts with each turn of the cutter or stroke of the saw.

The tubing will go all the way through the ferrules without damaging the ferrule sealing edge.

◎

◎

Tubing Handling

Wall Thickness

The accompanying tables show working pressure ratings of tubing in a wide range of wall thicknesses. Except as noted,

allowable pressure ratings are calculated from S values as specified by ASME B31.3, Process Piping. FITOK tube fittings have

been repeatedly tested in both the minimum and maximum wall thicknesses shown. FITOK tube fittings are not recommended

for tube wall thicknesses outside the ranges shown in the accompanying tables for each size.

tube fittings are designed to work properly with the tubing that is suggested in the ordering instructions.

stainless steel tube fittings have been repeatedly tested successfully with tubing with hardness up to 200 HV and 90 HRB.

FITOK FITOK

Hardness

Material

Metal tubing material should be softer than fitting material. For example, stainless steel tubing should not be used with

brass fittings. When tubing and fittings are made of the same material, tubing must be fully annealed.

Surface finish is very important to proper sealing. Tubing with any kind of depression, scratch, raised portion, or other surface

defect will be difficult to seal, particularly in gas service.

Surface Finish

Contents

Tubing

Pipes

Stainless Steel Seamless Pipe D-17

D-05

D-08

D-09

Stainless Steel Seamless Tubing

Copper Tubing

Carbon Steel Tubing

Suggested Allowable Working Pressure Tables

D-11

D-11

D-12

D-12

D-13

D-13

D-14

D-10

Alloy C-276 Tubing

Alloy 20 Tubing

Alloy 600 Tubing

Grade 2 Titanium Tubing

SAF 2507 Super Duplex Tubing

Alloy 825 Tubing

Alloy 625 Tubing

Alloy 400 Tubing

Suggested Allowable Working Pressure for Additional Alloys

D-14Pressure Ratings at Elevated Temperatures

D-16

D-15

Part Number Description

Ordering Information

Base Ordering Number

D-04Tubing Selection

D-04Tubing Handling

D-05Gas Service

D-05Tubing Installation


Metric, mm

19

21

23

25

31

32

34

40

46

50

54

63

3

6

8

10

12

14

15

16

18

20

22

25

28

30

32

38

50 80

1/2

23/32

3/4

13/16

7/8

15/16

1 3/16

1 1/4

1 5/16

1 1/2

2

2 13/32

3 1/4

Required straight tube length.

1/16

1/8

3/16

1/4

5/16

3/8

5/8

3/4

7/8

1 1/4

1 1/2

2

1

➀

Fractional, in.

TTube O.D. L➀ L➀

TTube O.D.

1/2

Tubing Installation

R

T

L

T Tube O.D.

L Required straight tube

length (see tables)

R Radius of tubing bend

Tubing properly selected and handled, combined with

properly installed tube fittings, will give you a

leaktight system and provide reliable service in a wide

variety of applications.

For maximum assurance of reliable performance, use:

Properly selected and handled high-quality tubing

such as provided by

tube fittings assembled in accordance

instructions.

An appropriate tube support system to limit the

movement of tubing and fluid system components.

When installing fittings near tube bends, there must be

sufficient straight length of tubing to allow the tube

bottomed in the fitting see tables

FITOK

— FITOK.

FITOK with

catalog

a

to be FITOK ( ).

◎

◎

◎

Figures and tables are for reference only. No implication is made that these values can be used for design work. Applicable

codes and practices in industry should be considered.

All pressures are calculated from equations in ASME B31.3, Process Piping. See factors for calculating working pressures in

accordance with ASME B31.1, Power Piping.

No allowance is made for corrosion or erosion.

Calculations are based on maximum O.D. and mimimum wall thickness, except as noted in individual tables.

Example: 1/2 in. O.D.×0.049 in. wall thickness stainless steel tubing purchased to ASTM A269:

O.D. Tolerance ±0.005 in. / Wall Thickness Tolerance ±10%

Calculations are based on 0.505 in.O.D.×0.0441 in. wall thickness tubing.

◎

◎

◎

Gas Service

Gases air, hydrogen, helium, nitrogen, etc.) have very small molecules that can escape through even the most minute

leak path. Some surface defects on the tubing can provide such a leak path. As tube outside diameter (O.D.) increases,

so does the likelihood of a scratch or other surface defect interfering with proper sealing.

The most successful connection for gas service will occur if all installation instructions are carefully followed and the

heavier wall thicknesses of tubing on the accompanying tables are selected.

(

Suggested Allowable Working Pressure Tables

1/16

1/8

3/16

1/4

5/16

3/8

1/2

5/8

3/4

7/8

1

1 1/4

1 1/2

0.010 0.012 0.014 0.016 0.020 0.028 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134 0.156 0.188

Nominal Wall Thickness, in.

Working Pressure, psig

Note: For gas service, select a tube thickness outside of the shaded area.

Table 1 — Fractional Stainless Steel Seamless Tubing

Allowable working pressures are calculated from an

S value of 20 000 psi (137.8 MPa) for ASTM A269 tubing

at -20 to 100°F (-28 to 37°C), as listed in ASME B31.3,

except as noted. Multiply stainless steel rating by 0.94

for working pressure in accordance with ASME B31.1.

Suggested Allowable Working Pressure for Stainless Steel Tubing

For Welded Tubing

Suggested Ordering Information

For welded and drawn tubing, a derating factor must be

applied for weld integrity:

For double-welded tubing, multiply working pressure

by 0.85.

For single-welded tubing, multiply working pressure

by 0.80.

◎

◎

TubeO.D.(in.)

High-quality, fully annealed (Type 304, 304L, 316, 316L) (seamless or welded and drawn) stainless

steel hydraulic tubing, ASTM A269 or A213, or equivalent. Hardness not to exceed 90 HRB or 200 HV. Tubing to be free

of scratches, suitable for bending and flaring. O.D. tolerances not to exceed 0.003 in. for 1/16 in. O.D. tubing.

Note: Certain austenitic stainless tubing has an allowable ovality tolerance double the O.D. tolerance and may not fit into

precision tube fittings. Dual-certified grades such as 304/304L and 316/316L meet the minimum chemistry and

the mechanical properties of both alloy grades.

±

FITOK

5600 6800 8100 9400 12000

8500 10900

5400 7000 10200

4000 5100 7500

4000 5800

3300 4800

2600 3700 6700

2900 5200 6000

2400 4200 4900 5800

2000 3600 4200 4800

10200

8000

6500

5100

4000

3300

2800

2400 3100 3600 4200 4700

2400 2800 3300 3600 4100 4900

2300 2700 3000 3400 4000 4900

Table 2—Metric Stainless Steel Seamless Tubing

For Welded Tubing

Allowable working pressures are based on equations

from ASME B31.3 for EN ISO 1127 tubing (D4, T4

tolerance for 3 to 12 mm; D4, T3 tolerance 14 to 50 mm),

using a stress value of 137.8 MPa (20 000 psi) and tensile

strength of 516.4 MPa (74 900 psi), except as noted.

Multiply stainless steel rating by 0.94 for working pressure

in accordance with ASME B31.1.

For welded and drawn tubing, a derating factor must

be applied for weld integrity:

For double-welded tubing, multiply working pressure

by 0.85.

For single-welded tubing, multiply working pressure

by 0.80.

◎

◎


3

6

8

10

12

14

15

16

18

20

22

25

28

30

32

38

0.8 1.0 1.2 1.5 1.8 2.0 2.2 2.5 2.8 3.0 3.5 4.0 4.5

Nominal Wall Thickness, mmTubeO.D.(mm) Working Pressure, bar

670

310 420 540 710

310 390 520

240 300 400 510 580

200 250 330 410 470

160 200 270 340 380 430 490

150 190 250 310 360 400 450

170 230 290 330 370 400

150 200 260 290 320 370

140 180 230 260 290 330 380

140 160 200 230 260 300 340

180 200 230 260 290 320

180 200 230 260 280 330

170 180 210 240 260 310

160 170 200 220 240 290 330

140 160 190 200 240 270 310

4.5

Suggested Allowable Working Pressure for Carbon Steel Tubing

Table 3 — Fractional Carbon Steel Tubing

Allowable working pressures are calculated from an S value of 15 700 psi (108.2 MPa) for ASTM A179 tubing at -20 to 100

( 28 to 37 ), as listed in ASME B31.3. For working pressure in accordance with ASME B31.1, multiply by 0.85.

°

°

F

- C

High-quality, soft annealed seamless carbon steel hydraulic tubing, ASTM A179 or equivalent. Hardness not to exceed

72 HRB or 130 HV. Tubing to be free of scratches, suitable for bending and flaring.

8000

5100

3700 9600

7500

6200

4500 5900

3500 4600 5300

2900 3700 4300 5100

2400 3200 3700 4300

2100 2700 3200 3700 4100

1600 2100 2500 2900 3200 3600 4000 4600 5000

1800 2000 2400 2600 2900 3300 3700 4100 5100

0.028


Tube Wall Thickness, in.

0 035. 0 049. 0 065. 0 083. 0 095. 0 109. 0 120. 0 134. 0 148. 0 165. 0 180. 0 220.

TubeO.D.(in.)

1/8

3 16/

1 4/

5 16/

3 8/

1/2

5/8

3/4

7/8

1

1 1/4

1 1/2

9600

7000

5500

4500

3200

2600

2100

1800

1500

10200

6600

4800

3700

3100

2300

1800


Table 4 — Metric Carbon Steel Tubing

Allowable working pressures are based on equations from ASME B31.3 for DIN 2391 tubing, using a stress value of

113 MPa (16 300 psi) and tensile strength of 340 MPa (49 300 psi).

High-quality, soft annealed carbon steel tubing, DIN 2391 or equivalent. Hardness not to exceed 72 HRB or 130 HV.

Tubing to be free of scratches, suitable for bending and flaring.


630 790

290 370 460 590

270 330 430

210 260 330

170 210 270 330 380 420

150 180 230 280 320 350

140 170 210 260 290 330

130 150 200 240 270 300 350

140 170 210 240 270 310

120 160 190 210 240 270 310

110 140 170 190 210 240 280

100 120 150 170 180 210 240 260

150 160 190 210 230 270

140 150 170 200 210 250

130 140 160 180 200 230 270

120 130 150 160 190 230 260

3

6

8

10

12

14

15

16

18

20

22

25

28

30

32

38

Working Pressure, bar

Tube Wall Thickness, mmTubeO.D.(mm)

0 8. 1 0. 1 2. 1 5. 1 8. 2 0. 2 2. 2 5. 2 8. 3 0. 3 5. 4 0. 4 5.




High-quality, fully annealed (Type 304, 304L, 316, 316L) stainless steel tubing, EN ISO 1127 or equivalent. Hardness not to exceed 90 HRB or

200 HV. Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed ±0.076 mm for 3 mm O.D. tubing.

Note: Dual-certified grades such as 304/304L, 316/316L meet the minimum chemistry and the mechanical properties

of both alloy grades.


Tolerances for W.T. Lenth Tolerances

for Lenth

mm mm inch mm mm mm mm

0.035 1.0

0.035 1.0

0.035 1.0

0.049 1.2

0.049 1.2

0.065 1.5

0.049 1.2

0.065 1.5

0.065 1.5

0.065 1.5±0.20

+0.05-0.00

±0.10

±0.05

±0.10

4000+3.00-0.00

Wall Thickness

Dimensions and Tolerances:

Tolerances for O.D.

6

10

38

50

12

20

25

inch

Tube O.D.

1/4

3/8

1-1/2

2

1/2

3/4

1

BA (Bright Annealing) Tubing

Features: Finish-rolling with bright annealing treatment, achieving good internal surface finish; Hardness under HRB80; Low carbon, high

nickel, high chromium and molybdenum, better corrosion resistance; Close dimensional tolerance, better consistency in application; Longer

service life in marine environment application; Applicable to clean industry, such as semiconductor, biological pharmaceuticals, food proce-

ssing and other fields.

Composition:

C Mn P S Si Ni Cr Mo

≤0.035 ≤2.00 ≤0.045 ≤0.015 ≤1.00 12.0-14.0 17.0-18.0 2.50-3.00

Chemical Component

Internal Surface States:

Ra (μm) Ra (μinch)

≤0.38 ≤151/4 (6) OD≤ ≤22 (50)

Dimension in. (mm) Internal Surface Finish

MP (Mechanical Polishing) Tubing

Features: Cold drawn and with mechanical polishing,

acid pickling of internal surface; Hardness under HRB80;

Composition: In accordance with the standard require-

ments, please refer to the corresponding standard.

Dimensions and Tolerance: In accordance with the sta-

ndard requirements, please refer to the corresponding

standard.

Internal surface state: acid pickling, surface finish

Ra .≤ μ3.2 m

316/316L

Material


Allowable working pressures are calculated from an S value of 6000 psi (41.3 MPa) for ASTM B75 (B75M) and ASTM B88 (B88M)

tubing at 20 to 100 ( 28 to 37 ), as listed in ASME B31.3 and ASME B31.1.- F - C° °

Suggested Allowable Working Pressure for Copper Tubing

Table 5 — Fractional Copper Tubing


1/2

1/8

3/16

1/4

5/16

3/8

5/8

3/4

7/8

1

1 1/8

Tube Wall Thickness, in.TubeO.D.(in.)

High-quality, soft annealed seamless copper tubing, ASTM B75 (B75M) or equivalent. Also soft annealed

(Temper O) copper water tube, type K or type L to ASTM B88 (type A or type B to ASTM B88M).


Table 6 — Metric Copper Tubing



0.8 1.0 1.2 1 5. 1 8. 2.0 2 2. 2 5. 2 8. 3.0

0.028 0 030. 0 035. 0 049. 0 065. 0 083. 0 095. 0 109. 0 120. 0 134.

2700 3000 3600

1800 1900 2300 3400

1300 1400 1600 2500 3500

1300 1900 2700

1000 1600 2200

800 1100 1600 2100

900 1200 1600 1900

700 1000 1300 1500 1800

600 800 1100 1300 1500

500 700 900 1100 1300 1500

600 800 1000 1100 1300 1400

6

8

10

12

14

15

16

18

20

22

25

28

110 140 170 220

100 120 160

80 100 130

60 80 100 130 140

50 60 90 110 120

60 80 100 110 120

70 90 100 110 120

60 80 90 100 110

60 70 80 90 100 110

50 60 70 80 90 100

40 50 60 70 80 90 100

40 50 60 70 80 90

130


Suggested Allowable Working Pressure for Additional Alloys

Alloy 400 Tubing

Allowable working pressures are calculated from an S value of 18 700 psi (128.9 MPa) for ASTM B165 tubing at 20 to 100

(-28 to 37 C), as listed in ASME B31.3 and ASME B31.1.

- °F

°

A limited amount of test data is available on tube fittings used with special alloy tubing. For sizes not listed in the

following tables, we recommend that a sample of the tubing be provided for evaluation before installation. Please include

all pertinent information relating to system parameters. Give tubing sample to any of authorized FITOK representatives to

forward to the factory.

FITOK


0.028 0 035. 0 049. 0 065. 0 083. 0 095. 0 109. 0 120.

Tube Wall Thickness, in.TubeO.D.(in.)

Table 7 — Fractional

High-quality, fully annealed seamless alloy 400 hydraulic tubing, ASTM B165 or equivalent. Hardness not

to exceed 75 HRB or 137 HV. Tubing to be free of scratches, suitable for bending and flaring. O.D. toler-

ances not to exceed ±0.005 in (±0.13 mm).


Table 8 — Metric



0.8 1.0 1.2 1 5. 1 8. 2.0 2 2. 2 5. 2 8. 3.0

7900

3700

10 100

4 800

3 700

3 100

2 300

7000

5400

4400

3200

2200

9500

7300

6100

4400

3000

2200

4000

2900

4600

3400 3900 4300

1/8

1/4

5/16

3/8

1/2

3/4

1

6

8

10

12

14

18

20

25

310 620

450

350

290

390

290

220

180

160 240 270

490

350

280

230

190

150 200 240 270 300

180 210 240 270 290

170 190 210 240 270 290





Allowable working pressures are based on equations from ASME B31.3 and ASME B31.1 for a maximum S value of

20 000 psi (137.8 MPa).

Alloy C-276 Tubing


TubeO.D.(in.)

0.028 0 035. 0 049. 0 065.


High-quality, fully annealed alloy C-276 tubing, ASTM B622 or equivalent. Hardness not to exceed 100 HRB or 248 HV.

Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed ±0.005 in (±0.13 mm).


Table 9 — Fractional Table 10 — Metric

4000 5100 7500

4000 5800

3300 4800

1/4

5/16

3/8

2600 3700

1 0200

7 800

6 500

5 100

310 420 520 670

310 390 500

240 300 380

6

8

10

12 200 240 310


TubeO.D.(mm)

Tube Wall Thickness, mm

0.8 1 0. 1 2. 1 5.


20 000 psi (137.8 MPa).

Alloy 20 Tubing

High-quality, fully annealed seamless or welded and drawn alloy 20 tubing, ASTM B729, B468 or equivalent. Hardness

not to exceed 95 HRB. Tubing to be free of scratches, suitable for bending and flaring. O.D. tolerances not to exceed

±0.005 in .(±0.13 mm)



TubeO.D.(in.)

0.028 0 035. 0 049. 0 065.




TubeO.D.(mm)


0.8 1 0. 1 2. 1 5.

5100 7500

3300 4800

2600 3700

1 0200

6 500

5 100

310 420 520 670

240 300 380

6

10

12 200 240 310

1/4 4000

3/8

1/2

1/2






20 000 psi (137.8 MPa).

Alloy 600 Tubing


Allowable working pressures are based on equations from ASME B31.3 and a maximum S value of 16 700 psi (115.1 MPa) for

ASTM B338 tubing at -20 to 100 F (-28 to 37 C). For working pressure in accordance with ASME B31.1, multiply by 0.85.° °

Grade 2 Titanium Tubing


High-quality, fully annealed seamless or welded and drawn grade 2 titanium tubing, ASTM B338 or equivalent. Tubing to be

free of scratches, suitable for bending. O.D. tolerances not to exceed (±0.13 mm).±0.005 in



TubeO.D.(in.)

0.028 0 035. 0 049. 0 065.



TubeO.D.(mm)


0.8 1 0. 1 2. 1 5.

6

10

12

1/4

3/8

3500 4500 6700 9100

2900 4200 5800

2100 3100 4200

290 380 470 600

210 260 340

180 220 2801/2



High-quality, fully annealed, cold drawn #1 temper alloy 600 seamless alloy tubing, ASTM B167 or equivalent. Hardness not

to exceed 92 HRB or 198 HV. Tubing to be free of scratches, suitable for bending and flaring. Order to outside diameter and

wall thickness only, not to inside diameter, average wall specification. O.D. tolerances not to exceed (±0.13 mm).±0.005 in



TubeO.D.(in.)

0.028 0 035. 0 049. 0 065.



TubeO.D.(mm)


0.8 1 0. 1 2. 1 5.

5100 7500

3300 4800

2600 3700

10200

6500

5100

310 420 520 670

240 300 380

6

10

12 200 240 310

1/4 4000

3/8

1/2



Alloy 625 Tubing

Allowable working pressures are calculated from an S value of 26 700 psi (184.1 MPa) for ASTM B444 Grade 2 tubing at

-20 to 100 28 to 37 tubing outside diameter and wall thickness tolerances from ASTM B444 for small-diameter tube.° ° F (- C),

➀

➁

➂

Based on 375°F (190°C) max.

Dual-certified grades such as 304/304L and 316/316L meet the minimum chemistry and the mechanical properties of both alloy grades.

Based on the lower derating factor for stainless steel, in accordance with ASME B31.3.

Temperature

°F °C Copper Ti

0 80. 1 00. 1 00. 0 87. 1 00. 1 00. 0 86. 0 90.

0 50. 0 93. 0 96. 0 79. 0 96. 0 96. 0 61. 0 82.

0 82. 0 85. 0 79. 0 85. 0 85. 0 45. 0 80.

0 76. 0 79. 0 75. 0 79. 0 79.

0 69. 0 76. 0 76.

Pressure Ratings at Elevated Temperatures

93

204

315

426

537

200

400

600

800

1000

CarbonSteel ➀

Tubing Materials

Alloy400

Alloy 20➂

AlloyC-276➂

1 00.

0 96.

0 85.

0 79.

0 35.

Alloy 600➂

SAF 2507

0 95.

0 87. ➀

Table 22 — Elevated Temperature Factors

To determine allowable working pressure at elevated temperatures, multiply allowable working pressures from Tables 1

through 21 by a factor shown in Table 22.

Example: Type 316 stainless steel 1/2 in. O.D. 0.035 in. wall at 1000 F

1. The allowable working pressure at 20 to 100 F 28 to 37 C) is 2600 psig Table 1, page 6

2. The elevated temperature factor for 1000 F (537 C) is 0.76 Table 22, above):

2600 psig 0.76 1976 psig

The allowable working pressure for 316 SS 1/2 in. O.D. 0.035 in. wall tubing at 1000 F 537 C is 1976 psig.

°

- ° (- ° ( D-0 ).

° ° (

=

° ( ° )

×

×

×

304/304L➁

316/316L➁

1/4

3/8


TubeO.D.(in.)

0.035 0 049.


1/2


6

10

12


TubeO.D.(mm)


0 8. 1 0. 1 2.

470 610 750

350 430

290 350

7300

4700

3500

10 700

6 800

5 000

0 065.

14 600

9 400

6 800

High-quality, fully annealed seamless alloy 625 tubing, ASTM B444, Grade 1 or 2, or equivalent. Hardness not to exceed 25

HRC or 266 HV. Tubing to be free of scratches, suitable for bending and flaring.


1 00.

0 90.

0 84.

0 81.

0 93.

0 85.

0 79.

0 75.

0 73.

Alloy825

Alloy 625

1 5. 1 8.

550

450 550


Allowable working pressures are calculated from an S value of 38 700 psi 266.8 MPa) for ASTM A789 tubing at -20 to 100°

(-28 to 37° as listed in ASME B31.3.

( F

C),

Table 17 — Fractional SAF 2507 Super Duplex Tubing


TubeO.D.(in.)


1/2

1/4

3/8

5/8

3/4

10 000

6 500

5 000

15 000

10 100

7 200

5 800

4 700

12 700

10 100

7 600

6 300

12 900

10 100

8 500 10 000

0 035. 0 049. 0 065. 0 083. 0 095.

High-quality, fully annealed SAF 2507 super duplex tubing, ASTM A789 or equivalent. Hardness not to exceed 32 HRC.

Tubing to be free of scratches, suitable for bending and flaring.


Allowable working pressures are calculated from an S value of 23 300 psi (160.6 MPa) for ASTM B163 and ASTM B423

seamless tubing at -20 to 100° -28 to 37° For ASTM B704, Class 1 or equivalent welded and drawn tubing, multiply

working pressure by 0.85.

F ( C),

Alloy 825 Tubing

1/4

3/8


TubeO.D.(in.)

0.035 0 049. 0 065.


1/2

6400 9300

4100 5900

3000 4300

11 600

8 200

5 900

410 530 660

300 370 480

250 300 390 480

6

10

12


TubeO.D.(in.)


0 8. 1 0. 1 2. 1 5. 1 8.


High-quality, fully annealed seamless alloy 825 tubing, ASTM B163, ASTM B423, or equivalent. Fully annealed welded alloy

825 tubing, ASTM B704, class 1 or equivalent. Hardness not to exceed HR15T90 or 201 HV. Tubing to be free of scratches,

suitable for bending and flaring. Wall thickness tolerances not to exceed ±10%.




Ordering Information

Base Ordering Number

Basic Ordering Number

316

Weight

lb/ft

0.035

0.049

0.049

0.065

0.049

0.065

0.065

0.083

0.134

SS-ST4-035-

SS-ST4-049-

SS-ST6-049-

SS-ST6-065-

SS-ST8-049-

SS-ST8-065-

SS-ST12-065-

SS-ST16-083-

SS-ST24-134-

0.082

0.107

0.173

0.219

0.240

0.307

0.484

0.827

1.989

1/4

3/8

1/2

3/4

1

1 1/2

316

Weight

Kg/m

1.0 0.125

1.0 0.175

1.0

1.5

0.226

0.320

1.5 0.395

2.8 1.769

3.0 2.031

2.0 0.501

1.5 0.470

2.0 0.602

1.5 0.545

2.0 0.702

1.5 0.620

2.0 0.802

2.0 0.903

2.5 1.410

3.5 2.501

4.0

SS-ST6M-1.0-

SS-ST8M-1.0-

SS-ST10M-1.0-

SS-ST10M-1.5-

SS-ST12M-1.5-

SS-ST28M-2.8-

SS-ST30M-3.0-

SS-ST12M-2.0-

SS-ST14M-1.5-

SS-ST14M-2.0-

SS-ST16M-1.5-

SS-ST16M-2.0-

SS-ST18M-1.5-

SS-ST18M-2.0-

SS-ST20M-2.0-

SS-ST25M-2.5-

SS-ST32M-3.5-

SS-ST38M-4.0- 3.410

10

12

28

30

14

16

18

20

25

32

38

6

8

316L

316L

6L-ST4-035-

6L-ST4-049-

6L-ST6-049-

6L-ST6-065-

6L-ST8-049-

6L-ST8-065-

6L-ST12-065-

6L-ST16-083-

6L-ST24-134-

Fractional Stainless Steel Tubing

Metric Stainless Steel Tubing

6L-ST6M-1.0-

6L-ST8M-1.0-

6L-ST10M-1.0-

6L-ST10M-1.5-

6L-ST12M-1.5-

6L-ST28M-2.8-

6L-ST30M-3.0-

6L-ST12M-2.0-

6L-ST14M-1.5-

6L-ST14M-2.0-

6L-ST16M-1.5-

6L-ST16M-2.0-

6L-ST18M-1.5-

6L-ST18M-2.0-

6L-ST20M-2.0-

6L-ST25M-2.5-

6L-ST32M-3.5-

6L-ST38M-4.0-

Basic Ordering Number

304

S4-ST4-035-

S4-ST4-049-

S4-ST6-049-

S4-ST6-065-

S4-ST8-049-

S4-ST8-065-

S4-ST12-065-

S4-ST16-083-

S4-ST24-134-

304L

4L-ST4-035-

4L-ST4-049-

4L-ST6-049-

4L-ST6-065-

4L-ST8-049-

4L-ST8-065-

4L-ST12-065-

4L-ST16-083-

4L-ST24-134-

316

S4-ST6M-1.0-

S4-ST8M-1.0-

S4-ST10M-1.0-

S4-ST10M-1.5-

S4-ST12M-1.5-

S4-ST28M-2.8-

S4-ST30M-3.0-

S4-ST12M-2.0-

S4-ST14M-1.5-

S4-ST14M-2.0-

S4-ST16M-1.5-

S4-ST16M-2.0-

S4-ST18M-1.5-

S4-ST18M-2.0-

S4-ST20M-2.0-

S4-ST25M-2.5-

S4-ST32M-3.5-

S4-ST38M-4.0-

316L

4L-ST6M-1.0-

4L-ST8M-1.0-

4L-ST10M-1.0-

4L-ST10M-1.5-

4L-ST12M-1.5-

4L-ST28M-2.8-

4L-ST30M-3.0-

4L-ST12M-2.0-

4L-ST14M-1.5-

4L-ST14M-2.0-

4L-ST16M-1.5-

4L-ST16M-2.0-

4L-ST18M-1.5-

4L-ST18M-2.0-

4L-ST20M-2.0-

4L-ST25M-2.5-

4L-ST32M-3.5-

4L-ST38M-4.0-

WallThickness

(in.)

TubeO.D.(in.)

WallThickness

(mm)

TubeO.D.(mm)

SSST

60

49

20

MP

A26

9 -

-

-

-

-

1 2 3 4 5 6 8

10

12

14

16

20

24

Mate

rial

Typ

eTu

be O

.D.

Wall T

hic

kn

ess

Len

gth

Su

rface

Co

nd

itio

nSta

nd

ard

SS

316

6L

316L

S4

304

4L

304L

CS

Carb

on

Ste

el

CU

Co

pp

er

MA

llo

y 400

HC

A20

INC

Allo

y C

-276

Allo

y 20

Allo

y 600

TI2

D7

A85

Tit

an

ium

Gra

de 2

Du

ple

x 2507

Allo

y 825

A65

Allo

y 625

ST

Seam

less

Tu

bin

gFr

act

ion

al

1/1

6"

1/8

"

3/1

6"

1/4

"

5/1

6"

3/8

"

1/2

"

5/8

"

3/4

"

7/8

"

1"

1 1

/4"

1 1

/2"

Metr

ic

2M

3M

2 m

m

3 m

m

6M

6 m

m

8M

10M

8 m

m

10 m

m

12M

14M

14 m

m

15 m

m15M

16M

16 m

m

18 m

m18M

20M

20 m

m

22 m

m22M

25 m

m25M

28 m

m28M

30 m

m30M

32 m

m32M

38 m

m38M

12 m

m

Fract

ion

al

Metr

ic

028

0.0

28"

0.8

0.8

mm

035

0.0

35"

1.0

1.0

mm

049

0.0

49"

1.2

1.2

mm

065

0.0

65"

1.5

1.5

mm

083

0.0

83"

1.8

1.8

mm

095

0.0

95"

2.0

2.0

mm

109

0.1

09"

2.2

2.2

mm

120

0.1

20"

2.5

2.5

mm

134

0.1

34"

2.8

2.8

mm

156

0.1

56"

3.0

3.0

mm

188

0.1

88"

3.5

3.5

mm

4.0

4.0

mm

4.5

4.5

mm

Fract

ion

al

Metr

ic

11 f

oo

t0.1

M100 m

m

33 f

tee

0.5

M500 m

m

66 f

tee

1M

1000 m

m

20

20 f

tee

3M

3000 m

m

6M

6000 m

m

AST

M A

179

AST

M A

269

AST

M B

75

AST

M B

165

AST

M B

622

AST

M B

729

AST

M B

167

AST

M B

338

AST

M A

789

AST

M B

163

A179

A269

B75

B165

B622

B729

B167

B338

A789

B163

B444

AST

M B

444

Part

Nu

mb

er

Desc

rip

tio

n

50 f

tC

oil

ee

50C

100 f

tC

oil

ee

100C

20M

C20000 m

mC

oil

50000 m

mC

oil

50M

C

No

te: "Part

Nu

mb

er

Desc

rip

tio

n" is

use

d f

or

com

po

siti

on

ru

les

of

FITO

K

p

rod

uct

mo

del, N

ot

suit

ab

le f

or

speci

fic

pro

du

ct p

art

nu

mb

er

se

lect

ion

, n

ot

ran

do

m c

om

bin

ati

on

s. If

in d

ou

bt,

ple

ase

co

nta

ct

FI

TO

K g

rou

p o

r au

tho

rize

d a

gen

t.

Weight unit conversion:

1 lb/ft=1.488 Kg/m 1 Kg/m=0.672 lb/ft

R

efe

r to

Tab

le 1

to

21 f

or

tub

ing

wall t

hic

kn

ess

.

Stan

dard

mate

rials

of

coil t

ub

ing

: SS

, 6L,

S4, 4L,

CS,

CU

;

Co

il T

ub

ing

O.D

. : U

p t

o 1

/2", 14m

m;

For

coil t

ub

ing

of

oth

er

mate

rials

, O

.D.

or

len

gth

,

◎ ◎ ◎

p

lease

co

nta

ct

F

ITO

K g

rou

p o

r au

tho

rize

d a

gen

t.

②①: :

①

②②

②②

Mech

an

ically

Po

lish

ed

MP

BA

Bri

gh

t A

nn

eale

d

Hoses and ConnectorsMH, MM, PS, MP, TH and HC Series

Hoses and Connectors D-18D-17 Tubing and Pipes

Pip

e D

imen

sio

n 10.2

87

13.7

16

17.1

45

21.3

36

26.6

70

33.4

01

42.1

64

48.2

60

60.3

25

73.0

25

88.9

00

101.6

00

114.3

00

141.3

00

168.2

75

219.0

75

273.0

50

323.8

50

355.6

00

406.4

00

457.2

00

508.0

00

558.8

00

609.6

00

660.4

00

711.2

00

762.0

00

812.8

00

863.6

00

914.4

00

Sch

ed

ule

Nu

mb

er

510S

10

20

30

40S

40

STD

60

80S

80

XS

100

120

140

160

XX

S5S

Ou

tsid

e

Dia

mete

r

mm

1.6

51

1.6

51

1.6

51

1.6

51

1.6

51

1.6

51

2.1

08

2.1

08

2.1

08

2.1

08

2.7

69

2.7

69

2.7

69

3.4

04

3.9

62

3.9

62

4.1

91

4.1

91

4.7

75

4.7

75

5.5

37

6.3

50

1.6

51

1.6

51

1.6

51

1.6

51

1.6

51

1.6

51

2.1

08

2.1

08

2.1

08

2.1

08

2.7

69

2.7

69

2.7

69

3.4

04

3.9

62

3.9

62

4.1

91

4.1

91

4.7

75

4.7

75

5.5

37

6.3

50

1.2

45

1.6

51

1.6

51

2.1

08

2.1

08

2.7

69

2.7

69

2.7

69

2.7

69

3.0

48

3.0

48

3.0

48

3.0

48

3.4

04

3.4

04

3.7

59

4.1

91

4.5

72

4.7

75

4.7

75

4.7

75

5.5

37

5.5

37

6.3

50

7.9

25

1.2

45

1.6

51

1.6

51

2.1

08

2.1

08

2.7

69

2.7

69

2.7

69

2.7

69

3.0

48

3.0

48

3.0

48

3.0

48

3.4

04

3.4

04

3.7

59

4.1

91

4.5

72

6.3

50

6.3

50

6.3

50

6.3

50

6.3

50

6.3

50

7.9

25

7.9

25

7.9

25

7.9

25

7.9

25

7.9

25

6.3

50

6.3

50

6.3

50

7.9

25

7.9

25

7.9

25

9.5

25

9.5

25

9.5

25

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

1.4

48

1.8

54

1.8

54

2.4

13

2.4

13

2.9

00

2.9

72

3.1

75

3.1

75

4.7

75

4.7

75

4.7

75

4.7

75

7.0

36

7.7

98

8.3

82

9.5

25

9.5

25

11.1

25

12.7

00

12.7

00

14.2

75

15.8

75

15.8

75

15.8

75

15.8

75

15.8

75

1.7

27

2.2

35

2.3

11

2.7

69

2.8

70

3.3

78

3.5

56

3.6

83

3.9

12

5.1

56

5.4

86

5.7

40

6.0

20

6.5

53

7.1

12

8.1

79

9.2

71

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

1.7

27

2.2

35

2.3

11

2.7

69

2.8

70

3.3

78

3.5

56

3.6

83

3.9

12

5.1

56

5.4

86

5.7

40

6.0

20

6.5

53

7.1

12

8.1

79

9.2

71

10.3

12

11.1

25

12.7

00

14.2

75

15.0

88

17.4

75

17.4

75

17.4

75

19.0

50

1.7

27

2.2

35

2.3

11

2.7

69

2.8

70

3.3

78

3.5

56

3.6

83

3.9

12

5.1

56

5.4

86

5.7

40

6.0

20

6.5

53

7.1

12

8.1

79

9.2

71

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

9.5

25

10.3

12

12.7

00

14.2

75

15.0

88

16.6

62

19.0

50

20.6

25

22.2

25

24.6

13

2.4

13

3.0

23

3.2

00

3.7

34

3.9

12

4.5

47

4.8

51

5.0

80

5.5

37

7.0

10

7.6

20

8.0

77

8.5

60

9.5

25

10.9

73

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

2.4

13

3.0

23

3.2

00

3.7

34

3.9

12

4.5

47

4.8

51

5.0

80

5.5

37

7.0

10

7.6

20

8.0

77

8.5

60

9.5

25

10.9

73

12.7

00

15.0

88

17.4

75

19.0

50

21.4

38

23.8

25

26.1

87

28.5

75

30.9

63

2.4

13

3.0

23

3.2

00

3.7

34

3.9

12

4.5

47

4.8

51

5.0

80

5.5

37

7.0

10

7.6

20

8.0

77

8.5

60

9.5

25

10.9

73

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

12.7

00

15.0

88

18.2

63

21.4

38

23.8

25

26.1

87

29.3

62

32.5

37

34.9

25

38.8

87

11.1

25

12.7

00

14.2

75

18.2

63

21.4

38

25.4

00

27.7

88

30.9

63

34.9

25

38.1

00

41.2

75

46.0

25

20.6

25

25.4

00

28.5

75

31.7

50

36.5

25

39.6

75

44.4

50

47.6

25

52.3

75

4.7

75

5.5

63

6.3

50

6.3

50

7.1

37

8.7

38

9.5

25

11.1

25

13.4

87

15.8

75

18.2

63

23.0

12

28.5

75

33.3

25

35.7

12

40.4

88

45.2

37

50.0

13

53.9

75

59.5

38

7.4

68

7.8

23

9.0

93

9.7

03

10.1

60

11.0

74

14.0

21

15.2

40

17.1

20

19.0

50

21.9

46

22.2

25

25.4

00

25.4

00

1/8

1/4

3/8

1/2

3/4 1

1 1

/4

1 1

/2 2

2 1

/2 3

3 1

/2 4 5 6 8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

No

min

al W

all T

hic

kn

ess

, m

min

.

0.4

05

0.5

40

0.6

75

0.8

40

1.0

50

1.3

15

1.6

60

1.9

00

2.3

75

2.8

75

3.5

00

4.0

00

4.5

00

5.5

63

6.6

25

8.6

25

10.7

50

12.7

50

14.0

00

16.0

00

18.0

00

20.0

00

22.0

00

24.0

00

26.0

00

28.0

00

30.0

00

32.0

00

34.0

00

36.0

00

1. Th

e s

ched

ule

nu

mb

ers

of

5S,

10S,

40S,

an

d 8

0S

com

ply

wit

h A

SME B

36.1

9M

.

2. Th

e o

thers

co

mp

ly w

ith

ASM

E B

36.1

0M

.

NPS

Stainless Steel Seamless Pipe

Features

◎

◎

Nominal pipe sizes from NPS 1/8 to NPS 2.

Material, size, specification and heat code are indicated on the pipe surface.

◎

◎

◎

◎

◎

◎

◎

◎

◎

Core tube and fitting material: 316 stainless steel

Overbraid material: 304 stainless steel

Vacuum and positive pressure applications

Maximum working pressure: 3100 psig (213 bar)

Hose size: 1/4 to 2

End connections:

1/4 to 2 thread

1/4 to 2 and 6 mm to 22 mm tube fitting

Welded fitting-to-hose construction to ensure reliable seal

Standard and custom-length

" "

Working temperature: -325°F to 800°F (-200°C to 426°C)

" "

available

Features

Metal Flexible HosesMH, MM Series

Contents

D-26

D-30

D-34

Metal Flexible Hoses

PTFE-lined, Stainless Steel Braided Hoses

Multipurpose Push-on Hoses

Thermoplastic Hoses

Hose Connectors, Adapters and Sleeves

MH, MM Series

PS Series

MP Series

TH Series

D-36

HC Series

D-20

Hose Technical Data (MH Series)

Hose Technical Data (MM Series)

316 SS Core Tube

316 SS Tube Fitting304 SS Overbraid

InsideDiameter

in. ( )mm

0.25 (6.4)

0.38 (9.5)

0.50 (12.7)

0.75 (19.0)

1.00 (25.4)

1.25 (31.8)

1.50 (38.1)

2.00 (50.8)

in. ( )mm

0.75 (19.0)

0.87 (22.1)

1.04 (26.4)

1.61 (40.9)

1.89 (48.0)

2.16 (54.9)

2.33 (59.2)

3.10 (78.7)

Static

Min. Bend Radius

Dynamic

in. ( )mm

4.33 (110)

5.91 (150)

6.50 (165)

8.86 (225)

10.2 (259)

11.8 (300)

13.4 (340)

15.4 (391)

TemperatureRange

-325 to 800

(-200 to 426)

Working Pressure at

o o70 F (20 C)

psig ( )bar

1600 (110)

1470 (101)

1110 (76.4)

860 (59.2)

680 (46.8)

680 (46.8)

520 (35.8)

450 (31.0)

BurstPressure at

o o 70 F (20 C)

HoseSeries

6400 (440)

6000 (413)

4500 (310)

3500 (241)

2680 (184)

2600 (179)

2200 (151)

1800 (124)

MM4

MM6

MM8

MM12

MM16

MM20

MM24

MM32

psig ( )bar

NominalHose Size

1/4 (6.4)

3/8 (9.7)

1/2 (12.7)

3/4 (19.0)

1 (25.4)

1 1/4 (31.8)

1 1/2 (38.1)

2 (50.8)

in. ( )mmo oF ( C)

InsideDiameter

in. ( )mm

0.28 (7.1)

0.42 (10.6)

0.53 (13.5)

0.80 (20.3)

1.03 (26.0)

1.30 (33.0)

1.53 (38.9)

2.05 (52.1)

in. ( )mm

2.25 (57.2)

3.00 (76.2)

4.50 (114)

6.00 (152)

6.75 (171)

8.86 (225)

11.0 (280)

13.8 (350)

Static

Min. Bend Radius

Dynamic

in. ( )mm

10.0 (254)

12.0 (305)

16.0 (406)

17.0 (432)

20.0 (508)

23.0 (584)

26.0 (660)

32.0 (813)

TemperatureRange

-325 to 800

(-200 to 426)

Working Pressure at

o o70 F (20 C)

psig ( )bar

3100 (213)

2000 (137)

1800 (124)

1500 (103)

1200 (82.6)

950 (65.4)

900 (62.0)

500 (34.4)

BurstPressure at

o o 70 F (20 C)

HoseSeries

12400 (854)

8000 (551)

7200 (496)

6000 (413)

4800 (330)

3800 (261)

3600 (248)

2000 (137)

MH4

MH6

MH8

MH12

MH16

MH20

MH24

MH32

psig ( )bar

NominalHose Size

1/4 (6.4)

3/8 (9.7)

1/2 (12.7)

3/4 (19.0)

1 (25.4)

1 1/4 (31.8)

1 1/2 (38.1)

2 (50.8)

in. ( )mmo oF ( C)

Hoses and Connectors D-20D-19 Hoses and Connectors

Pressure vs. Temperature

The working pressure of the hose selected must not exceed the maximum pressure, including any pressure spikes of the system.

To determine actual working pressure ratings in accordance with pulsation, shock factors multiply by 0.5.

Pre

ssu

re (

b ar)

34.4

69.0

103

137

172

206

241

426

0

800

371

700

316

600

260

500

Temperature ( )°C

Temperature ( )°F

204

400

149

300

93

200

38

100

MH series

MM series

-200

-325

0

500

1000

1500

2000

2500

3000

3500

Pre

ssu

re (

p si

g)

-5 3Every FITOK metal flexible hose assembly is factory tested with helium to a maximum leak rate of 1 x 10 std cm /s.

FITOK metal flexible hose components are cleaned in accordance with FITOK standard cleaning (FC-01) for general

industrial procedures.

Shorter hoses are packed in cartons with suitable protective material, longer hoses are coiled, bagged and boxed

or crated.

Cleaning and Packaging

Testing

MH4

MH6MH8

MH12MH16

MH20MH24

MH32

Pre

ssu

re (

b ar)

34.4

69.0

103

137

0

426

800

371

700

316

600

260

500

Temperature ( )°C

Temperature ( )°F

204

400

149

300

93

200

38

100

-200

-325

500

1000

1500

2000

0

Pre

ssu

re (

p si

g)

MM4MM6

MM8

MM12

MM16 / MM20

MM24

MM32

Standard Assemblies

1. All dimensions are for reference only and are subject to change. For dimensions not shown above, please

contact the authorized representative or .

2. Types listed are standard. Other types are available upon request, refer to the ordering information.

FITOK Group

Tube Fitting to Male NPT End

Tube Adapter End

NominalHoseSize

in.

3/8

1/4

TubeAdapter

Size

in.

3/8

1/4

HoseSeries

MH6

MM6

MH4

MM4

in.(mm)

12 (305)

36 (914)

12 (305)

36 (914)

Overall

engthL Ordering Number

SS-MH6-FT6-F12

SS-MM6-FT6-F36

SS-MH4-FT4-F12

SS-MM4-FT4-F36

MinimumInside

Diameter

in.(mm)

0.27 (6.9)

0.16 (4.1)

0.27 (6.9)

0.16 (4.1)

MaximumOutside

Dimension

in.(mm)

1.01 (25.6)

0.81 (20.6)

0.91 (23.1)

0.76 (19.2)

Tube Fitting End

TubeFitting

Size

NominalHoseSize

in.in.

HoseSeries

OverallengthL Ordering Number

MinimumInside

Diameter

MaximumOutside

Dimension

in.(mm) in.(mm)

MH4

MM4

MH6

MM6

MH8

MM8

MH12

MM12

MH16

0.19 (4.8)

0.19 (4.8)

0.28 (7.1)

0.28 (7.1)

0.41 (10.4)

0.41 (10.4)

0.66 (16.0)

0.66 (16.0)

0.88 (22.4)

0.94 (23.8)

0.87 (22.0)

1.09 (27.7)

1.01 (25.7)

1.23 (31.3)

1.23 (31.3)

1.74 (44.2)

1.59 (40.5)

1.82 (46.3)

SS-MH4-FL4-F12

SS-MM4-FL4-F36

SS-MH6-FL6-F18

SS-MM6-FL6-F36

SS-MH8-FL8-F18

SS-MM8-FL8-F48

SS-MH12-FL12-F18

SS-MM12-FL12-F48

SS-MH16-FL16-F24

1/41/4

3/83/8

1/21/2

3/43/4

11

in.(mm)

12 (305)

36 (914)

18 (457)

36 (914)

18 (457)

48 (1220)

18 (457)

48 (1220)

24 (610)

TubeFitting

Size

NominalHoseSize

NPTSize

in.in.

HoseSeries

OverallLength Ordering Number

MinimumInside

Diameter

MaximumOutside

Dimension

in.(mm) in.(mm)

MH4

MM4

MH6

MM6

MH8

MM8

MH12

MM12

MH16

0.19 (4.8)

0.19 (4.8)

0.28 (7.1)

0.28 (7.1)

0.41 (10.4)

0.41 (10.4)

0.66 (16.0)

0.66 (16.0)

0.88 (22.4)

0.94 (23.8)

0.87 (22.0)

1.09 (27.7)

1.01 (25.7)

1.23 (31.3)

1.23 (31.3)

1.74 (44.2)

1.59 (40.5)

1.82 (46.3)

SS-MH4-FL4-NS4-F12

SS-MM4-FL4-NS4-F36

SS-MH6-FL6-NS6-F18

SS-MM6-FL6-NS6-F36

SS-MH8-FL8-NS8-F18

SS-MM8-FL8-NS8-F48

SS-MH12-FL12-NS12-F18

SS-MM12-FL12-NS12-F48

SS-MH16-FL16-NS16-F24

1/41/4

3/83/8

1/21/2

3/43/4

11

1/4

3/8

1/2

3/4

1

in. in.(mm)

12 (305)

36 (914)

18 (457)

36 (914)

18 (457)

48 (1220)

18 (457)

48 (1220)

24 (610)


End Connections

A

Tube Fittings

MinimumInside

Diameter

MaximumOutside

Diameter

0.19 (4.8)

0.28 (7.1)

0.28 (7.1)

0.41 (10.4)

0.50 (12.7)

0.63 (16.0)

0.88 (22.4)

1.09 (27.7)

1.34 (34.0)

1.88 (47.8)

4.8 (0.19)

6.4 (0.25)

7.9 (0.31)

9.7 (0.38)

0.94 (23.8)

0.94 (23.8)

1.09 (27.7)

1.23 (31.3)

1.23 (31.3)

1.74 (44.2)

1.82 (46.3)

2.23 (58.9)

2.61 (66.3)

3.48 (88.4)

20.6 (0.81)

20.6 (0.81)

31.3 (1.23)

38.8 (1.53)

End Connection Designator

NominalHose Size

FL4

FL6

FL6

FL8

FL10

FL12

FL16

FL20

FL24

FL32

ML6

ML8

ML10

ML12

in.

Dimensions

1/4

1/4

3/8

1/2

1/2

3/4

1

1 1/4

1 1/2

2

1/4

1/4

3/8

1/2

1.94 (49.3)

2.00 (50.8)

2.02 (51.3)

2.24 (56.9)

2.27 (57.7)

2.35 (59.7)

2.64 (67.1)

4.04 (103)

4.75 (121)

5.72 (145)

62.2 (2.45)

63.2 (2.49)

51.6 (2.03)

56.9 (2.24)

mm mm (in.)

A

TubeFitting

Size

1/4

3/8

3/8

1/2

5/8

3/4

1

1 1/4

1 1/2

2

6

8

10

12

in. in. (mm)

A

Tube Adapters

MinimumInside

Diameter

MaximumOutside

Diameter

0.16 (4.1)

0.27 (6.9)

0.37 (9.4)

0.58 (14.7)

0.80 (20.3)

4.1 (0.16)

7.1 (0.28)

8.9 (0.35)

0.81 (20.6)

1.01 (25.6)

1.23 (31.3)

1.53 (38.8)

1.82 (46.3)

20.6 (0.81)

25.6 (1.01)

31.3 (1.23)


NominalHose Size

FT4

FT6

FT8

FT12

FT16

MT6

MT10

MT12

in.

Dimensions

1/4

3/8

1/2

3/4

1

1/4

3/8

1/2

1.76 (44.7)

1.82 (46.2)

2.22 (56.4)

2.35 (59.7)

2.69 (68.3)

44.4 (1.75)

47.0 (1.85)

57.2 (2.25)

mm (in.)

A

TubeAdapter

Size

1/4

3/8

1/2

3/4

1

6

10

12

in.

in.

in. (mm)

A

Male FR Metal Gasket Face

Seal Fittings Swivel MinimumInside

Diameter

MaximumOutside

Diameter

0.18 (4.6)

0.40 (10.2)

0.65 (16.5)

0.87 (22.1)

0.81 (20.6)

1.23 (31.3)

1.52 (38.7)

1.53 (38.8)


NominalHose Size

SFR4

SFR8

SFR12

SFR16

FRSize

1/4

1/2

3/4

1

in. in. in. (mm)

Dimensions

1/4

1/2

3/4

1

2.60 (66.0)

2.83 (71.9)

4.19 (106)

4.80 (122)

A

Female FR Metal Gasket Face

Seal Fittings Swivel

Female Pipe Threads, NPT

Male Pipe Threads, NPT

MinimumInside

Diameter

MaximumOutside

Diameter

0.28 (7.1)

0.38 (9.7)

0.47 (11.9)

0.72 (18.3)

0.94 (23.9)

1.09 (27.7)

1.23 (31.3)

1.74 (44.2)

NPTSize


NominalHose Size

FNS4

FNS6

FNS8

FNS12

1/4

3/8

1/2

3/4

in. in. in. (mm)

Dimensions

1/4

3/8

1/2

3/4

1.81 (46.0)

1.87 (47.5)

2.18 (55.4)

2.21 (56.1)

A

MinimumInside

Diameter

MaximumOutside

Diameter

0.17 (4.3)

0.28 (7.1)

0.42 (10.7)

0.81 (20.6)

1.01 (25.6)

1.23 (31.3)

SwivelSize


NominalHose Size

SAN4

SAN6

SAN8

1/4

3/8

1/2

in. in. (mm)in.

Dimensions

1/4

3/8

1/2

1.87 (47.5)

1.98 (50.3)

2.25 (57.2)

A

MinimumInside

Diameter

MaximumOutside

Diameter

0.18 (4.6)

0.40 (10.2)

0.81 (20.6)

1.23 (31.3)

FOSize


NominalHose Size

SFFO4

SFFO8

1/4

1/2

in. in. (mm)in.

Dimensions

1/4

1/2

2.11 (53.6)

2.14 (54.4)

A

in. (mm)

MinimumInside

Diameter

MaximumOutside

Diameter

0.28 (7.1)

0.28 (7.1)

0.38 (9.7)

0.47 (11.9)

0.47 (11.9)

0.63 (16.0)

0.88 (22.4)

1.09 (27.7)

1.34 (34.0)

1.81 (46.0)

0.94 (23.9)

1.09 (27.7)

1.09 (27.7)

1.02 (25.8)

1.23 (31.3)

1.74 (44.2)

1.82 (46.3)

2.03 (51.6)

2.47 (62.6)

3.19 (81.0)

NPTSize


NominalHose Size

NS4

NS4

NS6

NS8

NS8

NS12

NS16

NS20

NS24

NS32

1/4

1/4

3/8

1/2

1/2

3/4

1

1 1/4

1 1/2

2

in. in.

Dimensions

1/4

3/8

3/8

1/4

1/2

3/4

1

1 1/4

1 1/2

2

1.80 (45.7)

1.81 (46.0)

1.81 (46.0)

1.99 (50.6)

2.15 (54.6)

2.22 (56.4)

2.54 (64.5)

3.06 (77.7)

3.72 (94.5)

4.19 (106)

A

Female FO O-Ring Face

Seal Fittings Swivel

A

A

A

A

oSAE 37 (JIC) Female Swivel

A

37

o

MinimumInside

Diameter

MaximumOutside

Diameter

0.18 (4.6)

0.40 (10.2)

0.65 (16.5)

0.87 (22.1)

0.87 (22.1)

1.23 (31.3)

1.74 (44.2)

2.03 (51.6)

FRSize


NominalHose Size

SFFR4

SFFR8

SFFR12

SFFR16

1/4

1/2

3/4

1

in. in. in. (mm)

Dimensions

1/4

1/2

3/4

1

2.00 (50.8)

2.16 (54.9)

4.19 (106)

4.80 (122)

A

End Connections

mm

in.


Example: SS-MH4-FT6-M710

SS: End connection material is 316 stainless steel.

MH4: MH series, hose size is 1/4 .

FT6: End 1 connection type and size is 3/8 tube adapter.

End 2 connection type and size is 3/8 tube adapter.

M710: Overall length is 710 mm.

"

"

"

◎

Lightweight construction for easy handling and installation

Core tube material: smooth virgin PTFE

Overbraid material: 304 stainless steel


Hose size: 1/4" to 1"

-65°F to 400°F (-53°C to 204°C)

Standard and custom-length available

◎

◎

◎

◎

◎

◎

Working temperature:

PTFE-lined, Stainless Steel Braided HosesPS Series

Features

Hose Technical Data

316 SS and other alloy end connections

Smooth Virgin PTFE Core Tube

304 SS Overbraid

End 1 and end 2 follow the orders and regulations below:

1. Metric Double Ferrules - Fractional Double Ferrules - Metric Tube Adapters - Fractional

Tube Adapters - NPT Threads - BSPT Threads - BSPP Threads -SAE/MS Parallel Threads -

37 Flare - Others

2. Put the sizes from the biggest down to the smallest if they are of the same type.

3. Put the female before male if they are of the same type and size.

in. ( )mmin. ( )mm

Min. Inside Bend Radius TemperatureRange

InsideDiameter

NominalHose Size

0.19 (4.8)

0.31 (7.9)

0.41 (10.3)

0.63 (15.9)

0.88 (22.2)

1/4 (6.4)

3/8 (9.5)

1/2 (12.7)

3/4 (19.0)

1 (25.4)

Static Dynamic

Working Pressure at

o o70 F (20 C)

Burst Pressure at

o o70 F (20 C)

psig ( )bar

1.5 (38 1).

3.5 (88 9).

4.5 (114)

6.0 (152)

9.0 (229)

2.0 (50.8)

5.0 (127)

6.0 (152)

7.5 (190)

11.3 (287)

-65 to 450

(-53 to 230)

3000 (206)

2500 (172)

2000 (137)

1500 (103)

1000 (68)

12000 (826)

10000 (690)

8000 (551)

6000 (413)

4000 (275)

in. ( )mm in. ( )mmo o

F ( C) psig ( )bar

Nominal Hose Size

End ConnectionMaterial

SS - MH4 FL6 NS6 F36 - - -

Hose End 1 Connection Type End 1 Connection SizeEnd 2 Connection

Type and Size

MM

MH

Mediumpressure hose

High pressure hose

6

3/8 (in.) or 6 mm

1/2 (in.) or 8 mm

5/8 (in.) or 10 mm

3/4 (in.) or 12 mm

M14 x 1.5

6

8

10

12

14

4

1 (in.) or 16 mm16

M18 x 1.518

M20 x 1.520

Same as End 1

Specify in the same way as the end 1 connection type and size

Overall Length

XX in.

XX mm

FXX

MXX1/4 (in.)

4 1/4"

3/8"

3 3/16 (in.) SS 316 SS

904L SS904L

1 1/4"

1 1/

8

12

16

1/2''

3/4"

Fractional Tube Fitting

Fractional Tube Adapter

Female JIC 37Flare Swivel

°

Female NPT

Female BSPT

Male BSPT

Male NPT

Female Metric Thread(for RG gasket)

Male Metric Thread(for RG gasket)

Metric Tube Fitting

Metric TubeAdapter

Male JIC 37Flare

°

Female FR FittingSwivel

Male FR FittingSwivel

FL

ML

FT

FNS

FRT

RT

FMS

MS

NS

MT

AN

SFFR

SFR

SAN

20

24

32

1"

2"

2"

Note: "Part Number Description" is used for composition

rules of FITOK product model, Not suitable for

specific product part number selection, not random

combinations. If in doubt, please contact FITOK

group or authorized agent.



Pressure vs. Temperature

Testing

Every FITOK PTFE-lined hose assembly is factory tested with pure water at 1.5 times the maximum working pressure.


FITOK PTFE-lined hose components are cleaned in accordance with FITOK standard cleaning (FC-01) for general

industrial procedures.

Shorter hoses are packed in cartons with suitable protective material, longer hoses are coiled, bagged and boxed

or crated.

PTFE-lined Hose Standard Assemblies

Tube Adapters

1. All dimensions are for reference only and are subject to change. For dimensions

not shown above, please contact the authorized representative or .

2. Sizes and types listed are standard. Other sizes and types are available on

request, refer to the ordering information.

FITOK Group

NominalHoseSize

in.

Ordering Number

in. in.(mm) in.(mm)in.(mm)

SS-PS4-FT4-F6

SS-PS4-FT4-F12

SS-PS4-FT4-F18

SS-PS4-FT4-F24

SS-PS4-FT4-F36

SS-PS4-FT4-F48

SS-PS4-FT4-F60

SS-PS4-FT4-F72

SS-PS4-FT4-F120

SS-PS6-FT6-F12

SS-PS6-FT6-F18

SS-PS6-FT6-F24

SS-PS6-FT6-F36

SS-PS6-FT6-F48

SS-PS6-FT6-F60

SS-PS6-FT6-F72

SS-PS6-FT6-F96

SS-PS6-FT6-F120

SS-PS8-FT8-F12

SS-PS8-FT8-F24

SS-PS8-FT8-F36

SS-PS8-FT8-F48

SS-PS8-FT8-F60

SS-PS8-FT8-F72

SS-PS12-FT12-F24

SS-PS12-FT12-F36

SS-PS16-FT16-F36

SS-PS16-FT16-F48

SS-PS4-MT6-F12

SS-PS4-MT6-F24

SS-PS4-MT6-F36

SS-PS8-MT12-F24

SS-PS8-MT12-F36

1/4 1/4 0.16(4.1)

0.54(13.7)

3/8 3/80.27(6.9)

0.73(18.5)

1/2 0.36(9.1)

0.86(21.8)

1/2

3/40.53

(13.5)1.04

(26.4)3/4

10.80

(20.3)1.36

(34.5)1

in. mm in.(mm) in.(mm)

60.16(4.1)

0.54(13.7)1/4

120.33(8.4)

0.86(21.8)1/2

OverallLength

TubeAdapter

Size

MinimumInside

Diameter

MaximumOutside

Diameter

in.(mm)

6.0 (153)

12.0 (305)

18.0 (458)

24.0 (610)

36.0 (915)

48.0 (1220)

60.0 (1530)

72.0 (1829)

120.0 (3050)

12.0 (305)

18.0 (458)

24.0 (610)

36.0 (915)

48.0 (1220)

60.0 (1530)

72.0 (1829)

96.0 (2439)

120.0 (3050)

12.0 (305)

24.0 (610)

36.0 (915)

48.0 (1220)

60.0 (1530)

72.0 (1829)

24.0 (610)

36.0 (915)

36.0 (915)

48.0 (1220)

12.0 (305)

24.0 (610)

36.0 (915)

24.0 (610)

36.0 (915)


Temperature ( )°C

Temperature ( )°F

Pre

ssu

re (

psi

g)

Pre

ssu

re (

bar)

100 200 300 400 600

0

300

600

900

1200

1500

1800

2100

2400

2700

3000

3300

0

20 7.

41 4.

62 1.

82 8.

103 4.

124 1.

144 8.

165 5.

186 2.

206 9.

227.6

38 93 149 204 316

PS4

PS6

PS8

PS12

PS16

-100

-73.3

302 S

tain

less

Ste

el

Spri

ng

Gu

ard

Cle

ar

PV

C C

ove

rP SP

PS

PTFE

ho

se

(hig

h-p

ress

ure

)

No

min

al

Ho

se S

ize

Ho

se

SS

PS4

FL6

FT6

M1000

-

-

-

-

- P

F2

En

d 1

Co

nn

ect

ion

Siz

eEn

d C

on

nect

ion

Mate

rial

Overa

ll

Len

gth

SS

316 S

S

A20

Allo

y 20

S4

304 S

S

INC

HC

Allo

y 600

Allo

y C

-276

TI

Tit

an

ium

4 6 8

12

16

1/4

"

3/8

"

1/2

''

3/4

"

1"

En

d 1

Co

nn

ect

ion

Typ

e

4 6 8

12

14

16

18

20

1/4

(in

.)

3/8

(in

.) o

r 6 m

m

5/8

(in

.) o

r 10 m

m

3/4

(in

.) o

r 12 m

m

M14 x

1.5

1 (

in.)

or

16 m

m

M18 x

1.5

M20 x

1.5

10

XX

in

.

XX

mm

FXX

MX

X

Exa

mp

le:

SS-P

S4-S

AN

4-M

500

SS

: E

nd

co

nn

ect

ion

ma

teri

al

is 3

16

sta

inle

ss s

tee

l.

PS

4:

PS s

eri

es,

ho

se i

nsi

de

dia

me

ter

is 3

/16

.

SA

N4

: E

nd

1 c

on

ne

ctio

n t

ype

an

d s

ize

is

1/4

o

fi

ttin

g s

ize

, fe

ma

le J

IC 3

7 f

lare

sw

ive

l.

E

nd

2 c

on

ne

ctio

n t

yp

e a

nd

siz

e i

s 1

/4

o

fitt

ing

siz

e,

fem

ale

JIC

37

fla

re s

wiv

el.

M5

00

: O

ve

rall

le

ng

th i

s 5

00

mm

.

"

" "

En

d 2

Co

nn

ect

ion

Typ

e a

nd

Siz

e

Sam

e a

s En

d 1

Speci

fy in

th

e

sam

e w

ay

as

the

en

d 1

co

nn

ect

ion

ty

pe a

nd

siz

e

Op

tio

n

1/2

()

8

in.

or

mm

1. O

pti

on

s an

d a

ccess

ori

es

do

no

t ch

an

ge h

ose

tech

nic

al d

ata

. H

ose

op

era

tin

g

p

ara

mete

rs m

ust

be c

on

sid

ere

d w

hen

sele

ctin

g a

co

ver.

2.

PV

C c

ove

r re

sist

s ab

rasi

on

.

3. 302 s

tain

less

ste

el sp

rin

g g

uard

co

vers

en

tire

ho

se t

o p

rote

ct a

gain

st

kin

kin

g a

nd

ab

rasi

on

.

4.

Luci

d

To

ord

er

a h

ose

ass

em

bly

wit

h s

peci

al cl

ean

ing

an

d p

ack

ag

ing

(FC

-02),

fo

llo

win

g

A

STM

G93 le

vel C

, ad

d -

F2 a

s a s

uff

ix t

o t

he o

rderi

ng

nu

mb

er.

E

xam

ple

: SS-P

S4-F

T4-F

24-F

2.

En

d 1

an

d e

nd

2 f

ollo

w t

he o

rders

an

d r

eg

ula

tio

ns

belo

w:

1. M

etr

ic D

ou

ble

Ferr

ule

s -

Fract

ion

al D

ou

ble

Ferr

ule

s -

Metr

ic T

ub

e A

dap

ters

- F

ract

ion

al

T

ub

e A

dap

ters

- N

PT T

hre

ad

s -

BSP

T T

hre

ad

s -

BSP

P T

hre

ad

s -

SAE/M

S Para

llel

Th

read

s -

3

7

Flare

- O

thers

2. Pu

t th

e s

izes

fro

m t

he b

igg

est

do

wn

to

th

e s

mallest

if

they

are

of

the s

am

e t

ype.

3. Pu

t th

e f

em

ale

befo

re m

ale

if

they

are

of

the s

am

e t

ype a

nd

siz

e.

Cle

an

ing

an

d

Pack

ag

ing

FC-0

1

FC-0

2F2

904L

904L

SS

Fem

ale

(f

or

RG

gask

et)

Metr

ic T

hre

ad

Male

(f

or

RG

)

Metr

ic T

hre

ad

gask

et

Metr

ic T

ub

e A

dap

ter

Fem

ale

JIC

37

Flare

Swiv

el

°

Fem

ale

Metr

ic T

hre

ad

Sw

ivel

(fo

r R

G g

ask

et)

Fem

ale

BSP

P S

wiv

el

(fo

r R

G

)g

ask

et

Fract

ion

al

Tu

be

Fitt

ing

Metr

ic T

ub

e F

itti

ng

Fract

ion

al

Tu

be

Ad

ap

ter

Male

JIC

37

Flare

°

Fem

ale

NPT

Male

NPT

Fem

ale

BSP

T

Male

BSP

T

FNS

NS

FRT

RT

FMS

MS

FLML

FTMT

AN

SA

N

SM

S

SR

G

Part

Nu

mb

er

Desc

rip

tio

n

No

te: "Part

Nu

mb

er

Desc

rip

tio

n" is

use

d f

or

com

po

siti

on

ru

les

of

FITO

K p

rod

uct

mo

del, N

ot

suit

ab

le f

or

sp

eci

fic

pro

du

ct p

art

nu

mb

er

sele

ctio

n, n

ot

ran

do

m

co

mb

inati

on

s. If

in d

ou

bt,

ple

ase

co

nta

ct F

ITO

K

g

rou

p o

r au

tho

rize

d a

gen

t.


0

3.4

6.8

10.3

13.7

17.2

20.7

24.1

Pre

ssu

re (

bar)

Pre

ssu

re (

psi

g)

350653720-40

300

250

200

150

100

50

-400

10070

88

150 200

Temperature ( )°C

Temperature ( )°F

TemperatureRange

in. ( )mmin. ( )mm

InsideDiameter

Nominal Hose Size

Min. InsideBend Radius

Working Pressure at

o-40 to 70 F

o(-40 to 20 C)

Min. Burst Pressure

o oat 70 F (20 C)

psig (bar)

2.50 (63.5)

3.00 (76.2)

5.00 (127)

7.00 (178)

0.26 (6.6)

0.39 (9.9)

0.50 (12.7)

0.76 (19.3)

1/4 (6.4)

3/8 (9.5)

1/2 (12.7)

3/4 (19.0)

-40 to 200

(-40 to 93)300 (20.6) 1200 (82.7)

psig (bar)in. ( )mm ° °F( C)

◎

◎

◎

◎

◎

◎

◎

◎

◎

◎

Cover: weatherproof, abrasion withstanding and oil-resistant synthetic rubber

Reinforcement: single-braid high-strength synthetic fiber woven for maximum

strength and end connection retention

Core tube: highly oil-resistant rubber

Hose colors: blue, black, green, gray, red and yellow

Maximum working pressure: 300 psig (20.7 bar)

Hose size: 1/4 to 3/4

-40 F to 190 F (-40 C to 88 C)

End connection materials: stainless steel and brass

End connections reusable

Custom-length

" "

° ° ° °

available


Features

Hose Technical Data Pressure vs. Temperature

Multipurpose Push-on HosesMP Series

Synthetic Rubber

Synthetic Rubber Tube

One High-strength Synthetic Yarn Laid

◎ Do not reuse hose.

Caution:

Testing

Every FITOK multipurpose push-on hose assembly is factory tested with pure water at 1.5 times the maximum working pressure.


FITOK multipurpose push-on hose components are cleaned in accordance with FITOK standard cleaning (FC-01) forgeneral industrial

procedures.

Shorter hoses are packed in cartons with suitable protective material, longer hoses are coiled, bagged and boxed or crated.

Multipurpose Push-on Hose End Connections

Tube Fittings

A

B

NominalHoseSize

BasicOrdering Number

TubeFitting

Size

-MP4-FL4

-MP6-FL6

-MP8-FL8

A BMinimum

InsideDiameter

MaximumOutside

Diameter

1/4

3/8

1/2

1/4

3/8

1/2

1.97 (50.0)

2.11 (53.6)

2.47 (62.7)

1.21 (30.7)

1.24 (31.5)

1.42 (36.1)

0.16 (4.1)

0.27 (6.9)

0.37 (9.5)

0.67 (17.0)

0.87 (22.1)

1.02 (25.8)

in. in.

Dimensions, in.(mm)

Tube Adapters

A

B

Male NPT

A

B

Male BSPT

B

A

MinimumInside

Diameter

MaximumOutside

Diameter

Unions

A

B

NominalHose Size


-MP4-4

-MP6-6

-MP8-8

-MP12-12

1/4

3/8

1/2

3/4

in.

2.07 (52.6)

2.25 (57.2)

2.61 (69.8)

3.85 (97.8)

0.43 (11.4)

0.40 (12)

0.40 (14)

0.47 (12.0)

0.16 (4.1)

0.27 (6.9)

0.37 (9.5)

0.61 (15.6)

0.67 (17.0)

0.83 (21.1)

0.96 (24.5)

1.23 (31.3)

A B

Example: MP-8-F60-BK

MP: Hose series

8: Hose size is 1/2''.

F60: Overall length is 60 ."

BK: Hose color is black.

Hose Part aNumber Description

MP 4 F36 BK - - -

Hose Series

4

6

8

12

1/4(6.4mm)

"

3/8(9.5 mm)

"

1/2(12.7 mm)

''

3/4(19.0 mm)

"

Overall Length

XX in.

XX mm

FXX

MXX

MP

Hose Color

Blue

Black

Red

Green

Gray

BK

RD

GR

GY

YellowYW

Nominal Hose Size

MinimumInside

Diameter

MaximumOutside

Diameter

NominalHose Size


NPT Size

-MP4-NS4

-MP6-NS4

-MP6-NS6

-MP8-NS8

-MP12-NS12

1/4

3/8

3/8

1/2

3/4

in.

1/4

1/4

3/8

1/2

3/4

1.68 (42.7)

1.80 (45.7)

1.80 (45.7)

2.19 (55.6)

2.81 (71.4)

0.92 (23.4)

0.93 (23.6)

0.93 (23.6)

1.14 (29.0)

1.14 (29.0)

0.16 (4.1)

0.27 (6.9)

0.27 (6.9)

0.37 (9.5)

0.61 (15.6)

0.67 (17.0)

0.83 (21.1)

0.83 (21.1)

1.02 (25.9)

1.31 (33.3)

A B

Dimensions, in.(mm)

MinimumInside

Diameter

MaximumOutside

Diameter

0.15 (3.8)

0.24 (6.1)

0.34 (8.7)

0.57 (14.5)

3.8 (0.15)

4.1 (0.16)

5.6 (0.22)

6.9 (0.27)

8.1 (0.32)

8.6 (0.34)

0.67 (17.0)

0.83 (21.1)

0.98 (24.9)

1.23 (31.3)

17.0 (0.67)

17.0 (0.67)

21.1 (0.83)

21.1 (0.83)

24.9 (0.98)

31.3 (1.23)

NominalHoseSize


TubeAdapter

Size

-MP4-FT4

-MP6-FT6

-MP8-FT8

-MP12-FT12

-MP4-MT6

-MP4-MT8

-MP6-MT8

-MP6-MT10

-MP8-MT12

-MP12-MT18

1/4

3/8

1/2

3/4

1/4

1/4

3/8

3/8

1/2

3/4

in. in.

1/4

3/8

1/2

3/4

6

8

8

10

12

18

1.93 (49.0)

2.03 (51.6)

2.47 (62.7)

3.14 (79.8)

49.0 (1.93)

48.8 (1.92)

52.1 (2.05)

51.6 (2.03)

62.7 (2.47)

79.8 (3.14)

in. mm mm(in.)

1.17 (29.7)

1.16 (29.5)

1.42 (36.1)

1.48 (37.6)

29.7 (1.17)

29.5 (1.16)

30.0 (1.18)

29.5 (1.16)

36.1 (1.42)

37.3 (1.47)

A B

Dimensions, in.(mm)

MinimumInside

Diameter

MaximumOutside

Diameter

NominalHose Size


BSPT Size

-MP4-RT4

-MP6-RT4

-MP6-RT6

-MP8-RT8

-MP12-RT12

1/4

3/8

3/8

1/2

3/4

in.

1/4

1/4

3/8

1/2

3/4

1.68 (42.7)

1.80 (45.7)

1.80 (45.7)

2.19 (55.6)

2.81 (71.4)

0.92 (23.4)

0.93 (23.6)

0.93 (23.6)

1.14 (29.0)

1.14 (29.0)

0.16 (4.1)

0.27 (6.9)

0.27 (6.9)

0.37 (9.5)

0.61 (15.6)

A B

Dimensions, in.(mm)

Dimensions, in.(mm)

0.67 (17.0)

0.83 (21.1)

0.83 (21.1)

1.02 (25.9)

1.31 (33.3)







◎

◎

◎

◎

◎

◎

◎

◎

◎

Polyurethane cover: resists oil, weather and abrasion

Reinforcement: double-braid high-strength synthetic fiber

Core tube: nylon


Hose size: 3/16 to 1

-40 F to 200 F (-40 C to 93 C)

End connections: 1/4 to 1 thread, 1/4 to 1 and 6 mm to 22 mm tube fitting

End connection materials: stainless steel, brass and carbon steel

Custom-length

" "

° ° ° °

" "

available


Features

Thermoplastic HosesTH Series

Polyurethane Cover Fiber Reinforcement

Core Tube

Thermoplastic Hydraulic Hose (SAE 100R8)

Hose Series

Min. InsideBend

Radius Specification

NominalHose Size

InsideDiameter

Working Pressure at

o o70 F (20 C)

Min. Burst Pressure

o oat 70 F (20 C)

TemperatureRange

o oF ( C)

-40 to 200(-40 to 93)

SAE J517100R8

psig bar( )psig bar( )in. ( )mm in. ( )mm in. ( )mm

Thermoplastic Hydraulic Hose (SAE 100R7)

in. ( )mm in. ( )mm in. ( )mm

Hose Series

Min. InsideBend

Radius SpecificationNominal

Hose Size

TH3

TH4

TH5

TH6

TH8

InsideDiameter

Working Pressure at

o o70 F (20 C)

Min. Burst Pressure

o oat 70 F (20 C)

psig bar( )

TemperatureRange

o oF ( C)

1.58 (40)

1.97 (50)

2.36 (60)

2.95 (75)

3.74 (95)

-40 to 200(-40 to 93)

SAE J517100R7

psig bar( )

Technical Data

5000 (344)

5000 (344)

4000 (275)

3500 (241)

2250 (155)

2000 (137)

2.00 (50.8)

2.00 (50.8)

2.50 (63.5)

4.00 (102)

6.50 (165)

10.0 (254)

12000 (828)

11000 (758)

10000 (690)

9000 (620)

8000 (551)

3000 (207)

2750 (189)

2500 (173)

2250 (155)

2000 (137)

20000 (1378)

20000 (1378)

16000 (1102)

14000 (964)

9000 (620)

8000 (551)

0.19 (4.8)

0.25 (6.4)

0.38 (9.8)

0.50 (12.7)

0.75 (19.0)

1.00 (25.4)

0.19 (4.8)

0.25 (6.4)

0.31 (7.9)

0.38 (9.8)

0.50 (12.7)

TH3

TH4

TH6

TH8

TH12

TH16

3/16 (4.8)

1/4 (6.4)

3/8 (9.6)

1/2 (12.7)

3/4 (19.0)

1 (25.4)

3/16 (4.8)

1/4 (6.4)

5/16 (8.0)

3/8 (9.6)

1/2 (12.7)

Mu

ltip

urp

ose

Pu

sh-O

n H

ose

Cu

sto

m A

ssem

blie

s

Exa

mp

le:

SS-M

P4-F

T4-F

28-B

K

SS

: E

nd

co

nn

ect

ion

ma

teri

al

is 3

16

sta

inle

ss s

tee

l.

MP4

: M

P s

eri

es,

ho

se s

ize

is

1/4

".

FT

4:

En

d 1

co

nn

ect

ion

typ

e a

nd

siz

e i

s 1

/4"

tu

be

ad

ap

ter.

En

d 2

co

nn

ect

ion

typ

e a

nd

siz

e i

s 1

/4"

tu

be

ad

ap

ter.

F2

8:

Ove

rall

le

ng

th i

s 2

8"

.

BK

: H

ose

co

lor

is b

lack

.

En

d 1

an

d e

nd

2 f

ollo

w t

he o

rders

an

d r

eg

ula

tio

ns

belo

w:

1. M

etr

ic D

ou

ble

Ferr

ule

s -

Fract

ion

al D

ou

ble

Ferr

ule

s -

Metr

ic T

ub

e A

dap

ters

- F

ract

ion

al

T

ub

e A

dap

ters

- N

PT T

hre

ad

s -

BSP

T T

hre

ad

s -

BSP

P T

hre

ad

s -

SAE/M

S Para

llel Th

read

s -

3

7 F

lare

- O

thers

2. Pu

t th

e s

izes

fro

m t

he b

igg

est

do

wn

to

th

e s

mallest

if

they

are

of

the s

am

e t

ype.

3. Pu

t th

e f

em

ale

befo

re m

ale

if

they

are

of

the s

am

e t

ype a

nd

siz

e.

°

En

d C

on

nect

ion

Mate

rial

Ho

se S

eri

es

En

d 1

Co

nn

ect

ion

Typ

eEn

d 1

Co

nn

ect

ion

Siz

eEn

d 2

Co

nn

ect

ion

Typ

e a

nd

Siz

e

MP4

MP6

MP8

MP12

1/4

(6.4

mm

)"

3/8

(9.5

mm

)"

1/2

(12.7

mm

)''

3/4

(19.0

mm

)"

1/4

(in

.)

3/8

(in

.) o

r 6 m

m

1/2

(in

.) o

r 8 m

m

10 m

m

3/4

(in

.) o

r 12 m

m

18 m

m

6 8

10

12

184

Sam

e a

s En

d 1

Speci

fy in

th

e

sam

e w

ay

as

the

en

d 1

co

nn

ect

ion

ty

pe a

nd

siz

e

Overa

ll L

en

gth

XX

in

.

XX

mm

FXX

MX

X

SS

316 S

S

BB

rass

S4

304 S

S

Fract

ion

al

Tu

be F

itti

ng

Male

NPT

FLML

FTMT

NS

RT

Metr

ic

Tu

be F

itti

ng

Frac

tion

al T

ube

Ada

pter

Metr

ic T

ub

eA

dap

ter

Male

BSP

T

Ho

se C

olo

r

Blu

e

Bla

ck

Red

Gre

en

Gra

y

BK

RD

GR

GY

SSM

P4

4FT

4F3

6B

K -

-

-

-

-

FL

Yello

wY

W

904L

904L

SS

TestingEvery FITOK thermoplastic hose assembly is factory tested with pure water at 1.5 times the maximum working pressure.


FITOK thermoplastic hose components are cleaned in accordance with FITOK standard cleaning (FC-01) for general industrial procedures.

Shorter hoses are packed in cartons with suitable protective material, longer hoses are coiled, bagged and boxed or crated.

Part

aN

um

ber

Desc

rip

tio

n

No

te: "Part

Nu

mb

er

Desc

rip

tio

n" is

use

d f

or

com

po

siti

on

ru

les

of

FITO

K p

rod

uct

mo

del, N

ot

suit

ab

le f

or

sp

eci

fic

pro

du

ct p

art

nu

mb

er

sele

ctio

n,

no

t ra

nd

om

co

mb

inati

on

s. If

in d

ou

bt,

ple

ase

co

nta

ct F

ITO

K

g

rou

p o

r au

tho

rize

d a

gen

t.


◎

◎

◎

◎

◎

Used to connect soft plastic or rubber tubing.

Working pressures and are wider

than those of the connected hoses.

Stainless steel or brass is available.

Shank design holds tubing inside diameter securely.

Hose connectors are reusable.

working temperatures

Features

Hose Connectors and SleevesHC Series

Th

erm

op

last

ic H

ose

Ass

em

blie

s

Hose Connectors

Tube Fittings

Tube Adapters

F

L

1/8

1/4

1/4

3/8

1/4

1/4

3/8

3/8

3/4

1

-HC-F2-FT2

-HC-F2-FT4

-HC-F4-FT4

-HC-F4-FT6

-HC-F5-FT4

-HC-F6-FT4

-HC-F6-FT6

-HC-F6-FT8

-HC-F8-FT6

-HC-F8-FT8

-HC-F12-FT12

-HC-F16-FT16

1/2

1/2

1/8

1/4

5/16

3/8

3/4

1

1/2

Hose ID

in.

Basic

Ordering

Number

Tube Size

in.

0.08 (2.0)

0.09 (2.3)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.30 (7.6)

0.28 (7.1)

0.38 (9.7)

0.63 (16.0)

0.80 (20.3)

0.28 (7.1)

in.(mm)

MinimumInside

Diameter

1.37 (34.8)

1.47 (37.3)

1.86 (47.2)

1.92 (48.8)

1.94 (49.3)

1.94 (49.3)

2.26 (57.4)

2.07 (52.6)

2.33 (59.2)

2.50 (63.5)

3.03 (77.0)

2.00 (50.8)

in.(mm)

L

11/16

11/16

13/16

5/16

3/8

7/16

7/16

7/16

9/16

5/8

1 3/8

9/16

in.

F

Dimensions

mm ( )in.

0.08 (2.0)

0.09 (2.3)

0.19 (4.8)

0.19 (4.8)

0.28 (7.1)

0.38 (9.7)

4.8 (0.19)

6.4 (0.25)

6.4 (0.25)

7.9 (0.31)

9.7 (0.38)

mm

14

1.42 (36.1)

1.81 (46.0)

1.92 (48.8)

1.99 (50.6)

2.06 (52.3)

2.24 (56.9)

49.5 (1.95)

49.8 (1.96)

51.6 (2.03)

52.3 (2.06)

57.4 (2.26)

7/16

7/16

9/16

9/16

3/4

7/8

16

18

19

22

mm ( )in.

Hose ID

mm

1/8

1/4

3/8

1/2

6

8

10

12

in.

Tube Size

mm

1/8

1/8

1/4

1/4

3/8

1/2

6

8

10

10

12

in. in.(mm) in.(mm)in.

MinimumInside

DiameterLF

Dimensions

-HC-F2-FL2

-HC-F4-FL2

-HC-F4-FL4

-HC-F6-FL4

-HC-F6-FL6

-HC-F8-FL8

-HC-M6-ML6

-HC-M8-ML8

-HC-M8-ML10

-HC-M10-ML10

-HC-M12-ML12


SS

316 S

S

CS

S4

Carb

on

Ste

el

304 S

S

En

d C

on

nect

ion

Mate

rial

Ho

se S

eri

es

SST

H4

FL4

SAN

4M

1000

R7

-

-

-

-

-

En

d 1

Co

nn

ect

ion

Typ

eEn

d 1

Co

nn

ect

ion

Siz

eEn

d 2

Co

nn

ect

ion

Typ

e a

nd

Siz

e

TH

3

TH

4

TH

5

TH

6

TH

8

3/1

6(4

.8 m

m)

"

1/4

(6.4

mm

)"

5/1

6(7

.9 m

m)

"

3/8

(9.5

mm

)"

1/4

(in

.)

3/8

(in

.) o

r 6 m

m

1/2

(in

.) o

r 8 m

m

5/8

(in

.) o

r 10 m

m

3/4

(in

.) o

r 12 m

m

6 8

10

124

1 (

in.)

or

16 m

m16

Sam

e a

s En

d 1

Speci

fy in

th

e

sam

e w

ay

as

the

en

d 1

co

nn

ect

ion

typ

e a

nd

siz

e

Overa

ll

Len

gth

XX

in

.

XX

mm

FXX

MX

X

100R

7

100R

8

R7

R8Ho

se C

od

e

Exa

mp

le:

S S

-TH

4-F

L4-N

S4-F

36-R

7

SS

: E

nd

co

nn

ect

ion

ma

teri

al

is 3

16

sta

inle

ss s

tee

l.

TH

4: T

H s

eri

es,

ho

se s

ize

is

1/4

FL4

: En

d 1

co

nn

ect

ion

typ

e a

nd

siz

e i

s 1

/4 t

ub

e f

itti

ng

.

NS

4 : E

nd

2 c

on

ne

ctio

n t

yp

e a

nd

siz

e i

s 1

/4 m

ale

NP

T.

F3

6 :

Ove

rall

le

ng

th i

s 3

6

R7

: SA

E J

51

7 1

00

R7

.

"

"

"

1/2

(12.7

mm

)"

T

ub

e A

dap

ters

- N

PT T

hre

ad

s -

BSP

T T

hre

ad

s -

BSP

P T

hre

ad

s -

SAE/M

S Para

llel

Th

read

s -

En

d 1

an

d e

nd

2 f

ollo

w t

he o

rders

an

d r

eg

ula

tio

ns

belo

w:

1. M

etr

ic D

ou

ble

Ferr

ule

s -

Fract

ion

al D

ou

ble

Ferr

ule

s -

Metr

ic T

ub

e A

dap

ters

- F

ract

ion

al

3

7Fl

are

- O

thers

°

2. Pu

t th

e s

izes

fro

m t

he b

igg

est

do

wn

to

th

e s

mallest

if

they

are

of

the s

am

e t

ype.

3. Pu

t th

e f

em

ale

befo

re m

ale

if

they

are

of

the s

am

e t

ype a

nd

siz

e.

904L

904L

SS

Fem

ale

(f

or

RG

gask

et)

Metr

ic T

hre

ad

Male

(f

or

RG

)

Metr

ic T

hre

ad

gask

et

Metr

ic T

ub

e A

dap

ter

Fem

ale

JIC

37

Flare

Swiv

el

o

Fem

ale

Metr

ic T

hre

ad

Sw

ivel (f

or

RG

gask

et)

Fem

ale

BSP

P S

wiv

el

(fo

r R

G

)g

ask

et

Fract

ion

al Tu

be

Fitt

ing

Metr

ic T

ub

e F

itti

ng

Fract

ion

al Tu

be

Ad

ap

ter

Male

NPT

Male

BSP

T

NS

RT

FMS

MS

FLML

FTMT

SA

N

SM

S

SR

G

L

F

Part

aN

um

ber

Desc

rip

tio

n

No

te: "Part

Nu

mb

er

Desc

rip

tio

n" is

use

d f

or

co

mp

osi

tio

n r

ule

s o

f FI

TO

K p

rod

uct

m

od

el, N

ot

suit

ab

le f

or

speci

fic

pro

du

ct

p

art

nu

mb

er

sele

ctio

n, n

ot

ran

do

m

co

mb

inati

on

s. If

in d

ou

bt,

ple

ase

co

nta

ct

FI

TO

K g

rou

p o

r au

tho

rize

d a

gen

t.


-HC-F2-NS2

-HC-F2-NS4

-HC-F3-NS2

-HC-F3-NS4

-HC-F4-NS2

-HC-F4-NS4

-HC-F4-NS6

-HC-F4-NS8

-HC-F5-NS2

-HC-F5-NS4

-HC-F5-NS6

-HC-F5-NS8

-HC-F6-NS4

-HC-F6-NS6

-HC-F6-NS8

-HC-F8-NS4

-HC-F8-NS6

-HC-F8-NS8

-HC-F10-NS6

-HC-F10-NS8

-HC-F10-NS12

-HC-F12-NS8

-HC-F12-NS12

-HC-F12-NS16

-HC-F16-NS12

-HC-F16-NS16

0.08 (2.0)

0.08 (2.0)

0.13 (3.3)

0.13 (3.3)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.30 (7.6)

0.30 (7.6)

0.30 (7.6)

0.30 (7.6)

0.38 (9.7)

0.38 (9.7)

0.38 (9.7)

0.47 (11.9)

0.50 (12.7)

0.47 (11.9)

0.63 (16.0)

0.63 (16.0)

0.63 (16.0)

0.88 (22.4)

7/16

9/16

7/16

9/16

7/16

9/16

11/16

7/8

7/16

9/16

11/16

7/8

9/16

11/16

7/8

11/16

11/16

7/8

1 1/16

1 1/16

1 1/16

1 1/16

1 1/16

1 3/8

1 3/8

1 3/8

1.08 (27.4)

1.26 (32.0)

1.27 (32.2)

1.45 (36.8)

1.47 (37.3)

1.65 (41.9)

1.66 (42.2)

1.85 (47.0)

1.55 (39.4)

1.73 (43.9)

1.74 (44.2)

1.96 (49.8)

1.73 (43.9)

1.74 (44.2)

1.96 (49.8)

1.80 (45.7)

1.81 (46.0)

2.03 (51.6)

1.88 (47.8)

2.07 (52.6)

2.07 (52.6)

2.14 (54.4)

2.14 (54.4)

2.43 (61.7)

2.38 (60.5)

2.57 (65.3)

Hose ID

in.


NPT Size

1/8

1/4

1/8

1/4

1/8

1/4

3/8

1/2

1/8

1/4

3/8

1/2

1/4

3/8

1/2

1/4

3/8

1/2

3/8

1/2

3/4

1/2

3/4

1

3/4

1

1/8

3/16

1/4

5/16

3/8

1/2

5/8

3/4

1

in.(mm) in.(mm)in.

MinimumInside

DiameterLF

Dimensions

Hose ID

in.


NPT Size

-HC-F2-FNS2

-HC-F2-FNS4

-HC-F3-FNS2

-HC-F3-FNS4

-HC-F4-FNS2

-HC-F4-FNS4

-HC-F4-FNS6

-HC-F5-FNS4

-HC-F5-FNS6

-HC-F6-FNS4

-HC-F6-FNS6

-HC-F6-FNS8

-HC-F8-FNS8

1/8

3/16

1/4

5/16

3/8

1/2

0.08 (2.0)

0.08 (2.0)

0.13 (3.3)

0.13 (3.3)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.30 (7.6)

0.30 (7.6)

0.30 (7.6)

0.38 (9.7)

1/8

1/4

1/8

1/4

1/8

1/4

3/8

1/4

3/8

1/4

3/8

1/2

1/2

9/16

3/4

9/16

3/4

9/16

3/4

7/8

3/4

7/8

3/4

7/8

1 1/16

1 1/16

1.11 (28.2)

1.26 (32.0)

1.29 (32.8)

1.44 (36.6)

1.47 (37.3)

1.64 (41.7)

1.71 (43.4)

1.73 (43.9)

1.82 (46.2)

1.69 (42.9)

1.78 (45.2)

2.03 (51.6)

2.13 (54.1)

in.(mm) in.(mm)in.

MinimumInside

DiameterLF

Dimensions

F

LHose ID

in.


BSPT Size

-HC-F2- 2RT

-HC-F2-RT4

-HC-F3-RT2

-HC-F3-RT4

-HC-F4-RT2

-HC-F4-RT4

-HC-F4-RT6

-HC-F4-RT8

-HC-F5-RT2

-HC-F5-RT4

-HC-F5-RT6

-HC-F5-RT8

-HC-F6-RT4

-HC-F6-RT6

-HC-F6-RT8

-HC-F8-RT4

-HC-F8-RT6

-HC-F8-RT8

-HC-F10-RT6

-HC-F10-RT8

-HC-F10-RT12

-HC-F12-RT8

-HC-F12-RT12

-HC-F12-RT16

-HC-F16-RT12

-HC-F16-RT16

0.08 (2.0)

0.08 (2.0)

0.13 (3.3)

0.13 (3.3)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.30 (7.6)

0.30 (7.6)

0.30 (7.6)

0.30 (7.6)

0.38 (9.7)

0.38 (9.7)

0.38 (9.7)

0.47 (11.9)

0.50 (12.7)

0.47 (11.9)

0.63 (16.0)

0.63 (16.0)

0.63 (16.0)

0.88 (22.4)

7/16

9/16

7/16

9/16

716

9/16

11/16

7/8

7/16

9/16

11/16

7/8

9/16

11/16

7/8

11/16

11/16

7/8

1 1/16

1 1/16

1 1/16

1 1/16

1 1/16

1 3/8

1 3/8

1 3/8

1.28 (32.5)

1.40 (35.5)

1.40 (35.5)

1.58 (40.1)

1.47 (37.3)

1.65 (41.9)

1.66 (42.2)

1.90 (48.3)

1.67 (42.4)

1.86 (47.2)

1.87 (47.5)

2.10 (53.3)

1.73 (43.9)

1.74 (44.2)

1.96 (49.8)

1.80 (45.7)

1.81 (46.0)

2.03 (51.6)

1.88 (47.8)

2.07 (52.6)

2.07 (52.6)

2.14 (54.4)

2.14 (54.4)

2.43 (61.7)

2.38 (60.5)

2.57 (65.3)

1/8

1/4

1/8

1/4

1/8

1/4

3/8

1/2

1/8

1/4

3/8

1/2

1/4

3/8

1/2

1/4

3/8

1/2

3/8

1/2

3/4

1/2

3/4

1

3/4

1

1/8

3/16

1/4

5/16

3/8

1/2

5/8

3/4

1

in.(mm) in.(mm)in.

MinimumInside

DiameterLF

DimensionsL

F

Male NPT

L

F

Female NPT

Male BSPT

Female BSPT

L

F

BSPT SizeBasic

Ordering Number

Hose ID

in.

-HC-F2-FRT2

-HC-F2-FRT4

-HC-F3-FRT2

-HC-F3-FRT4

-HC-F4-FRT2

-HC-F4-FRT4

-HC-F4-FRT6

-HC-F5-FRT4

-HC-F5-FRT6

-HC-F6-FRT4

-HC-F6-FRT6

-HC-F6-FRT8

-HC-F8-FRT8

1/8

3/16

1/4

5/16

3/8

1/2

0.08 (2.0)

0.08 (2.0)

0.13 (3.3)

0.13 (3.3)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.19 (4.8)

0.30 (7.6)

0.30 (7.6)

0.30 (7.6)

0.38 (9.7)

1/8

1/4

1/8

1/4

1/8

1/4

3/8

1/4

3/8

1/4

3/8

1/2

1/2

9/16

3/4

9/16

3/4

9/16

3/4

7/8

3/4

7/8

3/4

7/8

1 1/16

1 1/16

1.11 (28.2)

1.26 (32.0)

1.29 (32.8)

1.44 (36.6)

1.47 (37.3)

1.64 (41.7)

1.71 (43.4)

1.73 (43.9)

1.82 (46.2)

1.69 (42.9)

1.78 (45.2)

2.03 (51.6)

2.13 (54.1)

in.(mm) in.(mm)in.

MinimumInside

DiameterLF

Dimensions


1. Sizes and types listed are standard. Other sizes and types are available

upon request, refer to the ordering information.

2. All dimensions are for reference only and are subject to change. For

dimensions not shown above, please contact the authorized

representative or .FITOK Group

L

F

E

Hose Connector SleevesHose ID

in.

Ordering Number

Hose OD

in.

AL-HC-F2-F4

AL-HC-F4-F6

AL-HC-F4-F7

AL-HC-F4-F8

AL-HC-F5-F7

AL-HC-F6-F8

AL-HC-F6-F9

AL-HC-F7-F10

AL-HC-F8-F11

AL-HC-F12-F16

0.26 (6.6)

0.41 (10.4)

0.46 (11.7)

0.52 (13.2)

0.48 (12.2)

0.55 (14.0)

0.61 (15.5)

0.69 (17.5)

0.76 (19.3)

1.10 (27.9)

3/8

9/16

5/8

11/16

5/8

11/16

3/4

13/16

7/8

1 1/4

0.40 (10.2)

0.79 (20.1)

0.79 (20.1)

0.79 (20.1)

0.87 (22.1)

0.87 (22.1)

0.87 (22.1)

0.94 (23.9)

0.94 (23.9)

1.07 (27.2)

1/8

1/4

1/4

1/4

5/16

3/8

3/8

7/16

1/2

3/4

1/4

3/8

7/16

1/2

7/16

1/2

9/16

5/8

11/16

1

Dimension, in. (mm)

E LF

◎

◎

Material: Aluminum

Reusable

Hose ClampsMin Hose OD Max Hose OD

mm mm

Ordering Number

CP8-12

CP10-16

CP12-20

CP16-25

CP20-32

CP25-40

8

10

12

16

20

25

12

16

20

25

32

40

◎

◎

Material: 304 SS

Reusable

Metric Thread

L

F

Hose ID

6

8

10

12

in.(mm) in.(mm)mm

MinimumInside

DiameterLF


Thread Size

-HC-M6-MS10

-HC-M6-MS12

-HC-M6-MS14

-HC-M8-MS14

-HC-M8-MS16

-HC-M10-MS16

-HC-M10-MS18

-HC-M12-MS20

-HC-M12-MS22

4.3 (0.17)

4.3 (0.17)

4.3 (0.17)

4.8 (0.19)

4.8 (0.19)

7.9 (0.31)

7.9 (0.31)

8.9 (0.35)

8.9 (0.35)

12

14

15

15

18

18

19

22

24

39.6 (1.54)

40.4 (1.59)

42.2 (1.66)

44.2 (1.74)

46.2 (1.82)

46.2 (1.82)

47.2 (1.86)

50.3 (1.98)

52.8 (2.08)

M10 x 1

M12 x 1.5

M14 x 1.5

M14 x 1.5

M16 x 1.5

M16 x 1.5

M18 x 1.5

M20 x 1.5

M22 x 1.5

Dimensions

Example: SS-HC-F4-FT6

SS: End connection material is 316 stainless steel.

FT6: End 2 connection type and size is 3/8 tube adapter.

HC: HC series.

F4: Hose ID is 1/4 ."

"

End ConnectionMaterial

End 1 Connection Type

SS HC F4 NS4－－－

Series

HC

M

Fractional

Metric

F

End 1 Connection Size End 2 Connection Type End 2 Connection Size

1/4 or 4 mm"

3/8 or 6 mm"

1/2 or 8 mm"

5/8 or 10 mm"

3/4 or 12 mm"

1 or 16 mm"

6

8

10

12

16

4 1/4 (in.)

3/8 (in.) or 6 mm

1/2 (in.) or 8 mm

5/8 (in.) or 10 mm

3/4 (in.) or 12 mm

1 (in.) or 16 mm

6

8

10

12

16

4

M18 x 1.518

M20 x 1.520

SS

304 SS

316 SS

S4

A20 Alloy 20

INC

HC

TI

Alloy 600

Alloy C-276

Titanium

AL Aluminum

904L 904L SS

FNS

RT

FMS

FL

ML

FT

FRT

MS

NS

MT

Fractional Tube Fitting

Fractional Tube Adapter

Female NPT

Female BSPT

Male BSPT

Male NPT

Female Metric Thread(for RG gasket)

Male Metric Thread(for RG gasket)

Metric Tube Fitting

Metric TubeAdapter

in.mm








tubing and pipes - inicio · allowable working pressures are based on equations from asme b31.3 for...

Documents