Method of Application:

By stiff bristle- brush/Plural feed airless spray gun

Pot life: 1/2 to 1 hours.

Thinner: Thinner 6756

Product Information

Limitations Uses

Application Details

The finish tends to chalk when exposed to sunlight although protective properties of the film remain practically unaffected.

Steel Surfaces:Degrease and blast clean to Sa 2 grade minimum of Swedish specification SIS - 05 -5900 - 1967.

Concrete SurfacesFor new concrete surface: Ensure that the surface is cured for minimum 2 months. Remove laitence, loose surface powder by light sand blasting. If blast cleaning is not feasible, roughen the surface by acid etching with 10% Hydrochloric Acid solution followed by thorough freshwater hosing to remove any residual acid. The surface should be perfectly dry and clean before applying Epigard solventless epoxy.

For old concrete surface: For old concrete surface: Remove grease, oil etc by solvent wiping. Remove water-soluble contaminants by fresh water hosing. Roughen the surface by acid etching, if light sand blasting is not feasible. The surface should be perfectly dry and clean before applying Epigard solventless epoxy.

Surface Preparation

1

EPIGARD SOLVENTLESSEPOXY COATING

PROTECTIVE COATINGS

DATA SHEET NO. 2006-025

Steel Surfaces:

of Swedish specification SIS - 05 -5900 - 1967.

Concrete Surfaces

cured for minimum 2 months. Remove laitence, loose surface powder by light sand blasting. If blast cleaning is not feasible, roughen the surface by acid etching with 10% Hydrochloric Acid solution followed by thorough freshwater hosing to remove any residual acid. The surface should be perfectly dry and clean before applying Epigard solventless epoxy.

For old concrete surface:

solvent wiping. Remove water-soluble contaminants by fresh water hosing. Roughen the surface by acid etching, if light sand blasting is not feasible. The surface should be perfectly dry and clean before applying Epigard solventless epoxy.

Colour

Finish

Mixing Ratio

Recommendeddry film thickness

TheoreticalSpreading Rate

Interval beforeOvercoating

In case the stipulated over coating period is over, for application of subsequent coat of paint the surface should be sweep blasted for better intercoat adhesion.

Drying time

Storage life

Dry Heat Resistance

Selected Range

Semi Glossy

Base : Accelerator3 : 2 (by weight/volume)

Minimum - 16 hoursMaximum - 48 hours

200 - 400 microns per coat

5 2.5 Sq. metre per litre

Upto 100o C (Intermittent)

Surface dry 5 - 8 hours.Handleable 18 - 24 hoursFull curing - 7 days

Upto 9 months so long as thematerial is stored in sealedcontainers under standardwarehouse storage conditions.

A two pack solvent free high performance high build epoxy coating specially designed for application as an internal coating of both steel and concrete tanks for storage of both sweet and sour crude oils,unleaded petrol, MTBE, ATF,selected range of aliphatic and aromatic hydrocarbon solvents and water. This product is suitable for safe storage of potable water also. It gives a very tough wear resistant, impervious coating to withstand many chemicals, fats and oils.

Interior tank lining,Urea Prilling Tower Internal, Floor Coating, Cooling tower, Effluent treatment plant etc.

DATA SHEET NO. 2006-025EPIGARD SOLVENTLESS EPOXY COATING

DISCLAIMER: The information in this leaflet is given in good faith. The company will not be liable for loss or damage howsoever caused including liability for negligence, which may be suffered by the user of the data contained therein. It is the user's responsibility to conduct all necessary tests to confirm the suitability of any product or system for their intended use. No guarantee of result is extended since conditions of use are beyond our control.

1. This cancels all previous literature on this product and is subject to revision without notice

2. Do not apply when temperature falls below 10o C or rises above 50o C and when relative humidity rises above 90%. Do not apply during rain, fog or mist.

3. Use off mixed paint within stipulated pot life period.

System Selection Guide

Health and Safety

Precaution

Shalimar Paints Ltd.: 4th Floor, Plot No. 64, Sector-44Gurgaon -122001, Haryana (India) | P: +91-124-4616600 | F: +91-124-4616659E: askus@shalimarpaints.com | www.shalimarpaints.com

Acids Alkalis Solvents Salt Water

Good Excellent Excellent Excellent Excellent

Good Excellent Excellent Excellent Excellent

EXPOSURE

SPLASH & SPILLAGE

FUMES & OUTDOOREXPOSURE

NOTES

Please refer to the separate safety data sheet available with detailed information.

For proper curing of film, ambient temperature should not be lower than 10o C.

Chemical Resistance Guide

2

Rev

isio

n-1,

Apr

il 20

14

System Selection Guide

Chemical Resistance Guide

SURFACE

Epigard 5 HB ZincPhosphate PrimerRed/Grey

Epigard HPOffwhite Primer.

Bipigard CTE XL Black /Bipigard 580 HB CTE Black

Epigard solventlessepoxy Coating.

Epigard solventlessepoxy Coating.

Epigard solventlessepoxy Coating.

Epigard solventlessepoxy Coating.

ConcreteSurface