umt0108at001 - enfora enabler hs 1000 - at command manual - rev 1_00.pdf
TRANSCRIPT
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
1/143
Enfora Enabler HS1000
AT Command Referenc
UMT0108AT00
Version:1.00
09 December, 201
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
2/143
Terms Of Use
TERMS OF USE OF NEW MATERIALS - PLEASE READ CAREFULLY
From time to time, Enfora, in its sole discretion, may make available for download on its website(www.enfora.com), or may transmit via mail or email, updates or upgrades to, or new releases of, the
firmware, software or documentation for its products (collectively, 'New Materials'). Use of such New
Materials is subject to the terms and conditions set forth below, and may be subject to additional terms
and conditions as set forth in Enfora's Technical Support Policy (posted on its website) and/or any written
agreement between the user and Enfora.
All New Materials are provided AS IS. Enfora makes no warranty or representation with respect to the
merchantability, suitability, functionality, accuracy or completeness of any such New Materials. The user of
such New Materials assumes all risk (known or unknown) of such use. Enfora reserves all rights in such
New Materials. The user shall have only a revocable and limited license to use such New Materials in
connection with the products for which they are intended. Distribution or modification of any NewMaterials without Enfora's consent is strictly prohibited.
IN NO EVENT WILL ENFORA BE RESPONSIBLE FOR ANY INCIDENTAL, INDIRECT, CONSEQUENTIAL OR
SPECIAL DAMAGES AS A RESULT OF THE USE OF ANY NEW MATERIALS. ENFORA'S MAXIMUM LIABILITY
FOR ANY CLAIM BASED ON THE NEW MATERIALS SHALL NOT EXCEED FIFTY U.S. DOLLARS ($50).
Copyright
2010 Enfora, Inc. All rights reserved. Complying with all applicable copyright laws is the responsibility of
the user. Without limiting the rights under copyright, no part of this document may be reproduced, stored
in or introduced into a retrieval system, or transmitted in any form or by any means (electronic,
mechanical, photocopying, recording or otherwise), or for any purpose, without the express written
permission of Enfora, Inc.
Enfora and the Enfora logo are either registered trademarks or trademarks of Enfora, Inc. in the United
States.
251 Renner Pkwy
Richardson, TX 75080 USA
972-633-4400
Phone: (972) 633-4400
Fax: (972) 633-4444Email: [email protected]
www.enfora.com
- i -
http://www.enfora.com/ -
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
3/143
Table of Contents
Terms Of Use i
Copyright i
Introduction 1
Document Scope 1
Platform Reference and Use 1
Command Syntax 1
Standard AT Commands 3
AT Commands Saved Into Non-Volatile Memory 4
AT Commands related to Audio 6
General Commands 7
AT&F Set All TA Parameters to Factory Defined Configuration 7
AT+CGMI Request Manufacturer Identification 8AT+CGMM Request Manufacturer Model Identification 9
AT+CGMR Request Revision Identification 10
AT+CGSN Request IMEI 11
AT+GMI TAManufacturer ID 12
ATI Manufacturer InformationAbout TA 13
ME TA Commands 14
AT+CEER Extended Error Reporting 14
AT+CFUN Set Phone Functionality 16
AT+CPIN Enter PIN 17
AT+CSCS Select TE Character Set 19AT+CMEE ReportMobile Equipment Errors 21
AT+CR-Service Reporting Control 22
AT+GCAP Request Overall Capabilities for TA 23
AT+IFC TE-TA Local Flow Control 24
AT+IPR Fixed TE-TAData Rate 25
AT+ICF TE-TACharacter Framing 26
ATE Command EchoMode 27
ATQ Result Code Suppression 28
ATS3 Command Line Termination Character 29
ATS4 Response Formatting Character 30ATS5 Editing Character 31
ATV Response Format 32
ATZ SetAll TA Parameters to Default Configuration 33
PhoneBookCommands 34
AT+CIND Indicator Control 34
- ii -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
4/143
AT+CPBR Read Phonebook Entries 36
AT+CPBS Select Phonebook Memory Storage 37
AT+CPBW Write Phonebook Entry 38
Call Control Commands 40ATA Answer a Call 40
ATD Dial command 41
ATS0 Automatic Response to a Network Request for PDP Context Activation 43
ATS10 Hang Up Delay 44
ATS6 Pause Before Blind Dialing 45
ATS7 Wait for Completion 46
ATS8 Dial Pause 47
AT+CLCC List currentcalls 48
AT+CPAS Phone ActivityStatus 50
AT+VTS DTMF and Tone Generation 51
AT+VTD Tone Duration 53
ATH HookControl 54
AT+MSTAT Connection Status 55
NetworkService Commands 57
AT+CLCK Facility Lock 57
AT+CIMI Request IMSI 59
AT+CMOD Call mode 60
AT+CPOL Preferred PLMN List 61
AT+CNUM Subscriber Number 63
AT+COPN Read Operators Name 64
AT+COPS PLMN Selection 65
AT+CPLS Selection of Preferred PLMN List 67
SMS Commands 68
AT+CMGC Send Command 68
AT+CMGD DeleteMessage 69
AT+CMGF Message Format 70
AT+CMGLList Messages 71
AT+CMGR Read Messages 72
AT+CMGS SendMessage 73
AT+CMGW Write Message to Memory 74
AT+CMMS More Messages to Send 75AT+CMSS SendMessage from Storage 76
AT+CNMA New MessageAcknowledgement to ME/TA 77
AT+CNMI NewMessage Indications to TE 78
AT+CPMS Preferred Message Storage 79
AT+CSCA Service Center Address 80
- iii -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
5/143
AT+CSMS Select Message Service 81
GPRS Commands 82
AT+CGACT Activate/Deactivate PDP Context 82
AT+CGATT PS Attach or Detach 84AT+CGCLASS GPRS Mobile Station Class 86
AT+CGDCONT Define PDP Context 87
AT+CGEQMIN Minimum Quality of Service Profile 89
AT+CGEQREQ 3G Quality of Service 93
AT+CGEREP Packet Domain Event Reporting 98
AT+CGPADDR Show PDP Address 100
AT+CGQMIN Minimum Quality of Service Profile 102
AT+CGQREQ Qualityof Service Profile (Requested) 104
AT+CGREG GPRS Network Registration Status 106
AT+CGSMS Select Service For MO SMS Messages 108
ATDRequest GPRS Service 109
NITZ Commands 110
AT+CSQ SignalQuality 110
Network Commands 112
AT+CPWC Band Setting 112
AT+CREG Network Registration 114
Miscellaneous Commands 116
AT+CPWD Change Password 116
AT+CUAD Application Discovery 118
AT+MCRSMRestricted SIM Access 119
AT+MCSIM Generic SIM Access 121
AT+MFLEX Request FLEX version 123
AT+MPDT Packet Data Transfer Indicator 124
AT+MSSCC Service Supported in Current Cell 126
AT+PACSP NetworkSelection Menu Availability 127
Appendix A Result Codes 128
Result Codes 128
Appendix B Error Codes 129
General Error Codes 129
GPRS Error Codes 131
SMS Error Codes (+CMS) 133Index 136
- iv -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
6/143
Introduction
Document ScopeThe following documentation pertains to the AT Command Set to be used in conjunction with the Enfora
Device identified in the title of this document.
Platform Reference and Use
The device will be referred to using various terms, to include: MS (Mobile Station), TA (Terminal Adapter),
DCE (Data Communication Equipment), or ME (Mobile Equipment).
The device can be controlled via the use of a DTE (Data Terminal Equipment) platform by issuing the AT
commands via a serial interface.
Command Syntax
The attention or AT prefix is required prior to entering any command. All commands require a carriage
return or following the entry of the desired command. All command responses are encapsulated by a
carriage return and line feed or . The ASCII display of these characters is suppressed with only
the modem response being presented.
In addition to terminating AT commands, the carriage return is also used to abort commands that
are executing.
Most AT commands complete immediately so there is no opportunity to abort them, for instance ATI.However, Some commands like AT+COPS or AT+CFUN can actually take several seconds to complete. The
AT command interface is said to be in execution mode when a command is running and has not returned a
result code (OK/ERROR). A second entered while the AT command interface is in execution mode will
abort the command and return the interface to command mode.
Some AT commands require additional input, for instance AT+CMGS. After terminating the AT+CMGS
command with a the AT command interface enters line edit mode. While in line edit mode all
characters are accepted except CNTL-Z. CNTL-Z terminates line edit mode and the AT command interface
enters execution mode. Like before, at this point another will abort the command.
AT message concatenation can be done using the ; between commands.
The following examples demonstrate the potential usage of AT commands presented:
Type Example Description
Command Format Query AT+GXXX=? When entered will return the command format and value ranges.
Com mand R ead AT+GXXX? W hen entered wil l return the current value assig ned to the com mand.
- 1 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
7/143
Command Write AT+GXXX=,, When entered will set the command to specified value(s).
Com mand E xecution AT+GXXX W hen entered wil l execute the specified com mand.
Command Concatenation AT+CRC=1;S0=1 When entered it will execute both the CRC and S0 command.
- 2 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
8/143
Standard AT Commands
The following is the format in which all commands will be presented.
ATx(Command) Xxxxx (Command Description)
Command Function (Description of the command function)
Command Functional Group (Functional group identification)
Command Format Query ATx=?
Response ATx: (parameter1 name 1 15), (parameter2 name 1-10),
Write Format ATx=,[,],
Response OK or ERROR
Read Format ATx?
Response ,,
Execution Format ATx
Response OK, ERROR, or
Parameter Values
ATx: (1-15),(1-10)
Reference (Applicable standard reference)
Standard Scope Mandatory or Optional
Enfora Implementation Scope Full, Partial, or Not Supported
Notes (Additional command notes)
Examples
Note: Where applicable, the responses provided for the READ and
EXECUTION formats are modem default values. All efforts will be made by
Enfora, Inc. to keep these values current in the documentation but will notbe responsible for any differences that may occur as a result subsequent
software builds and version enhancements.
- 3 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
9/143
AT Commands Saved Into Non-Volatile Memory
Certain AT commands can be saved into non-volatile memory (NVMEM). The commands that can be saved
are listed in the table below. In general, commands where settings can affect the operation of the modem,
can be saved into NVMEM. For example AT+CGDCONT or AT+CFUN. Status or execution commands
generally cannot be saved, such as AT+CSQ or AT+CPAS. Commands that can be saved in NVMEM will be
saved automatically when the new command is entered. The user does not have to enter AT&W (not
supported) to save the command. To set the command back to factory default the user can send AT&F (for
all commands) or re-enter the AT command with the factory settings. Either will automatically be saved in
NVMEM.
The full list of commands that can be saved in NVMEM is listed below;
AT+CGDCONT
AT+CGQMIN
AT+CGEQMIN
AT+CGEQREQ
AT+CGEREP
AT+CREG
AT+CGCLASS
AT+CGREG
AT+CPWC
AT+CGSMS
AT+CSMS
AT+CPMS
AT+CMGFAT+CNMI
AT+CSCA
AT+CSCS
AT+CMEE
AT+CLVL
AT+COPS
AT+CPOL
AT+CTTY
ATS0
ATS2ATS3
ATS4
ATS5
ATS6
ATS7
- 4 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
10/143
ATS8
ATS10
ATE
ATQ
ATVAT+IPR
AT+ICF
AT+IFC
AT+MDFP
AT+MNREC
AT+MPDT
AT+MSSCC
AT+MVGM
AT+MVGS
AT+PACSP
- 5 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
11/143
AT Commands related to Audio
The AT commands related to audio can be found in the following document Enfora HS1000 Modem Audio
Configuration Application Note UMT0108AN001
- 6 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
12/143
General Commands
AT&F Set All TA Parameters to Factory Defined Configuration
AT&F Set All TA Parameters to Factory Defined Configuration
Command Function Set All TA Parameters to Factory Defined Configuration
Command Functional Group State Control
Command Format Query N/A
Response N/A
Write Format N/A
Response N/ARead Format N/A
Response N/A
Execution Format AT&F
Response OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 6.1.2
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes The OK response is returned PRIOR to this command being
executed on the module to allow the response to be seen at the
current baud rate in case the factory default changes this (back to
autobaud). Allow one second after the returned OK before issuing
the next command.
While under CMUX, AT&F will not cause the modem to revert
back to the default baud rate.
- 7 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
13/143
AT+CGMI Request Manufacturer Identification
AT+CGMI Request Manufacturer Identification
Command Function This command is used to obtain the manufacturer identificationinformation.
Command Functional Group Equipment Information
Command Format Query AT+CGMI=?
Response OK
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format AT+CGMI
Response Enfora, Inc.
OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 5.1
Standard Scope Optional
Enfora Implementation Scope Full
Notes Return value is manufacturer specific.
- 8 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
14/143
AT+CGMM Request Manufacturer Model Identification
AT+CGMM Request Manufacturer Model Identification
Command Function This command is used to obtain the manufacturer modelidentification information.
Command Functional Group Equipment Information
Command Format Query AT+CGMM=?
Response OK
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format AT+CGMM
Response (for Enabler IIIG)
Response (for HS1000)
Enabler IIIG Modem
OK
DATA CARD
OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 5.2
Standard Scope Optional
Enfora Implementation Scope Full
Notes Return value is manufacturer specific.
- 9 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
15/143
AT+CGMR Request Revision Identification
AT+CGMR Request Revision Identification
Command Function AT+CGMR command shall retrieve the software version of themodule.
Command Functional Group USIM and Phonebook Access
Command Format Query N/A
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format +CGMR
Response
or
+CME ERROR:
Parameter Values
The total number of characters, including line terminators, in the
information text shall not exceed 2048 characters.
Reference
Standard Scope
Enfora Implementation Scope
Notes
- 10 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
16/143
AT+CGSN Request IMEI
AT+CGSN Request IMEI
Command Function This command is used to obtain the manufacturer InternationalMobile Equipment Identity (IMEI).
Command Functional Group Equipment Information
Command Format Query AT+CGSN=?
Response OK
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format AT+CGSN
Response 0044008824900101
OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 5.4
Standard Scope Optional
Enfora Implementation Scope Full
Notes Return value is manufacturer specific. The TA returns the
International Mobile station Equipment Identifier (IMEI).
- 11 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
17/143
AT+GMI TA Manufacturer ID
AT+GMI TA Manufacturer ID
Command Function TA returns information about the manufacturer.Command Functional Group Equipment Information
Command Format Query N/A
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/A
Execution Format AT+GMI
Response (For All Non HS1000)
Response (For HS1000)
Enfora, Inc.
OK
144.
OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 6.1.4
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes N/A
- 12 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
18/143
ATI Manufacturer Information About TA
ATI Manufacturer Information About TA
Command Function List manufacturer.Command Functional Group Equipment Information
Command Format Query N/A
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/A
Execution Format ATI
Response (For All Non HS1000)
Response (For HS1000)
Enfora, Inc.
OK
144.
OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 6.1.3
Standard Scope Optional
Enfora Implementation Scope Full
Notes N/A
- 13 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
19/143
ME TA Commands
AT+CEER Extended Error Reporting
AT+CEER Extended Error Reporting
Command Function Execution command causes the TA to return one or more lines of
information text , determined by the MT manufacturer,
which should offer the user of the TA an extended report of the
reason for
- the failure in the last unsuccessful call setup (originating or
answering) or in call modification;
- the last call release;- the last unsuccessful GPRS attach or unsuccessful PDP context
activation;
- the last GPRS detach or PDP context deactivation.
Typically, the text will consist of a single line containing the cause
information given by GSM/UMTS network in textual format.
Command Functional Group Call Control
Command Format Query AT+CEER=?
Response OK
Write Format N/AResponse N/A
Read Format N/A
Response N/A
Execution Format AT+CEER
Response +CEER: < >, 0 = data rate in baud per second
Reference ITU-T Recommendation V.25
Standard Scope Mandatory
Enfora Implementation Scope Partial
Notes When changing the value of AT+IPR, the new baud rate is
effective immediately. In order to properly save the new setting
and communicate with the modem, the user must change the
baud rate of the communicating device to the new baud rate
before any more communication with the modem can be
accomplished.
Recommended default = 0
- 25 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
31/143
AT+ICF TE-TA Character Framing
AT+ICF TE-TA Character Framing
Command Function This command determines the number of data/stop/parity bitsthat will be used by the TA serial interface.
Command Functional Group State Control
Command Format Query AT+ICF=?
Response +ICF: (0-6), (0-3)
OK
Write Format AT+ICF=,
Response OK
Read Format AT+ICF?Response +ICF: 3,3
OK
Execution Format N/A
Response N/A
Parameter Values
0 = Auto Detect
1 = 8 data, 2 stop, no parity
2 = 8 data, 1 stop,1 parity3 = 8 data, 1 stop, no parity
4 = 7 data, 2 stop, no parity
5 = 7 data, 1 stop, 1 parity
6 = 7 data, 1 stop, no parity
0 = odd
1 = even
2 = mark
3 = space
Reference GSM Ref. 07.0 Chapter 6.2.11
Standard Scope Mandatory
Enfora Implementation Scope Partial
Notes If no parity is specified in , then is ignored.
- 26 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
32/143
ATE Command Echo Mode
ATE Command Echo Mode
Command Function Determines whether the TA echoes characters typed locally.Command Functional Group State Control
Command Format Query N/A
Response N/A
Write Format ATE
Response OK
Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
0 =Do not echo characters locally
1= Echo characters locally
Reference GSM Ref. 07.07 Chapter 6.2.4
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes N/A
- 27 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
33/143
ATQ Result Code Suppression
ATQ Result Code Suppression
Command Function Determines whether or not the TA transmits any result code tothe TE.
Command Functional Group State Control
Command Format Query N/A
Response N/A
Write Format ATQ
Response OK
Read Format N/A
Response N/AExecution Format N/A
Response N/A
Parameter Values
0 =DCE transmits result codes
1 =Result codes are suppressed and not transmitted
Reference GSM Ref. 07.07 Chapter 6.2.5
Standard Scope MandatoryEnfora Implementation Scope Full
Notes N/A
- 28 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
34/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
35/143
ATS4 Response Formatting Character
ATS4 Response Formatting Character
Command Function Determines the character generated by the TA for result codeand information text.
Command Functional Group State Control
Command Format Query ATS4=?
Response S4(0-127)
OK
Write Format ATS4=
Response OK
Read Format ATS4?
Response 010
OK
Execution Format N/A
Response N/A
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 6.2.2
Standard Scope MandatoryEnfora Implementation Scope Full
Notes N/A
- 30 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
36/143
ATS5 Editing Character
ATS5 Editing Character
Command Function Determines the character recognized by the TA as a request todelete the preceding character form the command line.
Command Functional Group State Control
Command Format Query ATS5=?
Response S5(0-127)
OK
Write Format ATS5=
Response OK
Read Format ATS5?
Response 008
OK
Execution Format N/A
Response N/A
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 6.2.3
Standard Scope MandatoryEnfora Implementation Scope Full
Notes N/A
- 31 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
37/143
ATV Response Format
ATV Response Format
Command Function Determines the DCE response format, with or without headercharacter, and the use of numerical results code.
Command Functional Group State Control
Command Format Query N/A
Response N/A
Write Format ATV
Response OK
Read Format N/A
Response N/AExecution Format N/A
Response N/A
Parameter Values
0 = DCE transmits limited headers and trailers and numeric result
codes
1 = DCE transmits full headers and trailers and verbose response
text
Reference GSM Ref. 07.07 Chapter 6.2.6
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes N/A
- 32 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
38/143
ATZ Set All TA Parameters to Default Configuration
ATZ Set All TA Parameters to Default Configuration
Command Function Set All TA Parameters to Default Configuration.Command Functional Group State Control
Command Format Query N/A
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/A
Execution Format ATZ
Response OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 6.1.1
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes Non volatile memory is not reset.
- 33 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
39/143
PhoneBookCommands
AT+CIND Indicator Control
AT+CIND Indicator Control
Command Function This command is used for reading various indications l ike
signal strength, service availability, roam status, and smsful
status.
Command Functional Group Registration (Mobility Management) AT commands
Command Format Query +CIND=?
Response +CIND: (,(list of supported s)) [,(,(list of
supported s))[,...]]
+CME ERROR:
Write Format +CIND=[[,[,...]]]
Response +CME ERROR:
Read Format +CIND?
Response +CIND: [,[,...]]
+CME ERROR:
Execution Format
Response
Parameter Values
Integer type value, which shall be in range of corresponding
Values reserved by the present document and their
ranges:
"service" service availability (0-1)
"roam" roaming indicator (0-1)
"signal" signal quality (0-5)
"smsfull" a short message memory storage in the MT hasbecome full (1), or memory locations are available (0)
Note: The order of data returned would be
+CIND:"service","roam", "signal","sms full"
Reference
- 34 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
40/143
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 35 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
41/143
AT+CPBR Read Phonebook Entries
AT+CPBR Read Phonebook Entries
Command Function AT+CPBR shall read a specific record from the phonebookentries (of USIM) or records of specified range when
executed.
Command Functional Group USIM and Phonebook Access
Command Format Query +CPBR=?
Response +CPBR: ,,, [+CPBR:
,,,] +CME ERROR:
Write Format +CPBR=[,]
Response [+CPBR: ,,,
or+CME ERROR:
Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
, , Integer type values in the range of location numbers of
phonebook memory String type phone number of format
Type of phone number octet in integer format (refer 3GPP
TS 24.008 sub clause 10.5.4.7)
String type field of maximum length ; character set
as specified by command Select TE Character Set +CSCS
Integer type value indicating the maximum length of field
Integer type value indicating the maximum length of field
Examples
- 36 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
42/143
AT+CPBS Select Phonebook Memory Storage
AT+CPBS Select Phonebook Memory Storage
Command Function AT+CPBS command shall set the phone book memorystorage to be used.
Command Functional Group USIM and Phonebook Access
Command Format Query +CPBS=?
Response +CPBS: (list of supported s)
Write Format +CPBS=
Response +CME ERROR:
Read Format +CPBS?
Response +CPBS: [,,]+CME ERROR:
Execution Format N/A
Response N/A
Parameter Values
Values reserved by the present document
"SM" SIM/UICC phonebook. If a SIM card is present or if a
UICC with an active GSM application is present, the EFADN
under DFTelecom
is selected. If a UICC with an active USIM
application is present, the global phonebook, DFPHONEBOOKunder DF
Telecomis selected.
Integer type value indicating the number of used locations in
selected memory
Integer type value indicating the total number of locations in
selected memory
- 37 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
43/143
AT+CPBW Write Phonebook Entry
AT+ CPBW Write Phonebook Entry
Command Function AT+CPBW when executed shall write the phone book recordinto the storage entry specified.
Command Functional Group USIM and Phonebook Access
Command Format Query +CPBW=?
Response +CPBW: (list of supported s),[],
(list of supported s),[]
or
+CME ERROR:
Write Format +CPBW=[][,[,]
Response +CME ERROR:
Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
Integer type values in the range of location numbers of
phonebook memory
String type phone number of format
Type of phone number octet in integer format (refer 3GPP
TS 24.008 subclause 10.5.4.7) ; default 145 when dialing
string includes international access code character "+",
otherwise 129
String type field of maximum length ; character set
as specified by command Select TE Character Set +CSCS
Integer type value indicating the maximum length of field
Integer type value indicating the maximum length of field
Reference
Standard Scope
Enfora Implementation Scope
- 38 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
44/143
Notes
Examples
- 39 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
45/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
46/143
ATD Dial command
ATD Dial command
Command Function This command is used to setup an outbound voice or data call.Command Functional Group Call Control
Command Format Query N/A
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/A
Execution Format ATD1234567I;
Response NO DIALTONE (Non HS1000)
or
NO CARRIER
or
CONNECT (for Data only)
or
BUSY or
OK
Parameter Values
V.25ter Dialing Digits = 0 9, *, #, +, A, B, C
V.25ter Dialing Modifiers = , (comma), T, P, !, @, W
GSM Modifier Characters
I = Restrict CLI, i = Allow CLI
(Not applicable to HS1000)
Semicolon after dialing string or modifier indicates voice call and
forces TA into command mode after successful completion.
Reference GSM Ref. 07.07 Chapter 6.2
Standard Scope MandatoryEnfora Implementation Scope Full
Notes Modem Responses:
NO DIALTONE - if no dial tone is detected
NO CARRIER - if call cannot be set up
CONNECT - when connected in a non-voice call (data
- 41 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
47/143
mode) dependent on ATX setting
BUSY - if dialed number is busy
OK - when successful voice call or TA ends current call and
returns to command mode
- 42 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
48/143
ATS0 Automatic Response to a Network Request for PDP Context
Activation
ATS0 Automatic Response to a Network Request for PDP ContextActivation
Command Function The V.25ter 'S0=n' (Automatic answer) command may be used to
turn off (n=0) and on (n>0) the automatic response to a network
request for a PDP context activation.
Command Functional Group Modem Compatibility Command
Command Format Query ATS0=?
Response s0(0-255)
OK
Write Format ATS0=
Response OK
Read Format ATS0?
Response 000
OK
Execution Format N/A
Response N/A
Parameter Values
0 = do not answern>0 = establish data session
Reference GSM Ref. 07.07 Chapter 10.2.2.1
Standard Scope Optional
Enfora Implementation Scope Full
Notes N/A
- 43 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
49/143
ATS10 Hang Up Delay
ATS10 Hang Up Delay
Command Function This command sets the length of time, in tenths of seconds, towait before disconnecting after the carrier is lost. This is a
dummy command that will display a value that has been set, but
does not affect functionality.
Command Functional Group Call Control
Command Format Query ATS10=?
Response S10(1-254)
OK
Write Format ATS10=Response OK
Read Format ATS10?
Response (Non HS1000)
Response (HS1000)
001
OK
014
OK
Execution Format N/A
Response N/A
Parameter Values N/A
Reference ITU-T Ref. V.25ter Chapter 6.3.12
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes Does not affect GSM functionality.
- 44 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
50/143
ATS6 Pause Before Blind Dialing
ATS6 Pause Before Blind Dialing
Command Function Sets the number of seconds to wait after dialtone detectionbefore dialing. This is a dummy command and does not affect
functionality.
Command Functional Group Call Control
Command Format Query ATS6=?
Response S6(2-10)
OK
Write Format ATS6=
Response OK
Read Format ATS6?
Response 002
OK
Execution Format N/A
Response N/A
Parameter Values N/A
Reference ITU-T Ref. V.25ter Chapter 6.3.9
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes Does not affect GSM functionality.
- 45 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
51/143
ATS7 Wait for Completion
ATS7 Wait for Completion
Command Function This command sets the number of seconds to wait after dial tonedetection before dialing a number. This is a dummy command
that will display a value that has been set, but does not affect
functionality.
Command Functional Group Call Control
Command Format Query ATS7=?
Response S7(1-255)
OK
Write Format ATS7=
Response OK
Read Format ATS7?
Response (Non HS1000)
Response (HS1000)
060
OK
030
OK
Execution Format N/A
Response N/A
Parameter Values N/A
Reference ITU-T Ref. V.25ter Chapter 6.3.10
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes Does not affect GSM functionality.
- 46 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
52/143
ATS8 Dial Pause
ATS8 Dial Pause
Command Function This command sets the number of seconds to wait for the commadial modifier in the ATD dial string. This is a dummy command
that will display a value that has been set, but does not affect
functionality.
Command Functional Group Call Control
Command Format Query ATS8=?
Response S8(0-255)
OK
Write Format ATS8=Response OK
Read Format ATS8?
Response 002
OK
Execution Format N/A
Response N/A
Parameter Values N/A
Reference ITU-T Ref. V.25ter Chapter 6.3.11
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes Does not affect GSM functionality.
- 47 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
53/143
AT+CLCC List current calls
AT+CLCC List current calls
Command Function Returns list of current calls of ME. If command succeeds but nocalls are available, no information response is sent to TE.
Command Functional Group Call Control
Command Format Query AT+CLCC=?
Response OK
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format AT+CLCC
Response +CLCC: ,,, , [,,
[,]] [+CLCC: ,, ,,
[,, [,]][...]]]
OK
Parameter Values
integer type; call identification number as described in GSM
02.30 [19] subclause 4.5.5.1; this number can be used in +CHLD
command operations 0 = mobile originated (MO) call
1 = mobile terminated (MT) call
(state of the call):
0 = active
1 = held
2 = dialling (MO call)
3 = alerting (MO call)
4 = incoming (MT call)
5 = waiting (MT call)
(bearer/teleservice):
0 = voice
1 = data
2 = fax (fax not supported)
3 = voice followed by data, voice mode
4 = alternating voice/data, voice mode
- 48 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
54/143
5 = alternating voice/fax, voice mode
6 = voice followed by data, data mode
7 = alternating voice/data, data mode
8 = alternating voice/fax, fax mode
9 = unknown 0 = call is not one of multiparty (conference) call parties
1 = call is one of multiparty (conference) call parties
string type phone number in format specified by
type of address octet in integer format (refer GSM 04.08 [8]
subclause 10.5.4.7)
string type alphanumeric representation of
corresponding to the entry found in phonebook; used character
set should be the one selected with command Select TE Character
Set +CSCS
Reference GSM Ref. 07.07 Chapter 7.17
Standard Scope Optional
Enfora Implementation Scope Full
Notes N/A
- 49 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
55/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
56/143
AT+VTS DTMF and Tone Generation
AT+VTS DTMF and Tone Generation
Command Function This command allows the transmission of DTMF tones andarbitrary tones (see note). These tones may be used (for example)
when announcing the start of a recording period. The command is
write only. In this profile of commands, this command does not
operate in data mode of operation
Command Functional Group Audio Functions
Command Format Query AT+VTS=?
Response +VTS: (0, 1, 2, 3, 4, 5, 6, 7, 8, 9, #, *)
OK
Write Format N/A
Response N/A
Read Format N/A
Response N/A
Execution Format AT+VTS=
Response OK
Parameter Values
0
12
3
4
5
6
7
8
9
#
*Reference GSM Ref. 07.07 Chapter C.11
Standard Scope Optional
Enfora Implementation Scope Partial
Notes In GSM this operates only in voice mode. Fixed tone duration.
- 51 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
57/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
58/143
AT+VTD Tone Duration
AT+VTD Tone Duration
Command Function This refers to an integer that defines the length of tonesemitted as a result of the +VTS command. This does not affect the
D command. A value different than zero causes a tone of duration
/10 seconds. The value zero causes a "manufacturer specific"
value.
Audio Functions
Command Functional Group Audio Functions
Command Format Query AT+VTD=?
Response List of supported s)
Write Format N/A
Response N/A
Read Format AT+VTD?
Response
OK
Execution Format AT+VTS=
Response OK
Parameter Values
0-600
Reference GSM Ref. 07.07 Chapter C.11
Standard Scope Optional
Enfora Implementation Scope Partial
Notes In GSM/UMTS the value of tone duration is preset and cannot be
altered.
- 53 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
59/143
ATH Hook Control
ATH Hook Control
Command Function Disconnect an existing call.Command Functional Group Call Control
Command Format Query N/A
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/A
Execution Format ATH
Response OK
Parameter Values N/A
Reference ITU-T Ref. V.25ter Chapter 6.3.6
Standard Scope Mandatory
Enfora Implementation Scope Full
Notes If data call or session is active, +++ (escape sequence) must be
entered to go to command mode prior to sending ATH command.
- 54 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
60/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
61/143
Notes
- 56 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
62/143
Network Service Commands
AT+CLCK Facility Lock
AT+CLCK Facility Lock
Command Function AT+CLCK command shall try to lock, unlock or interrogate a
ME or a network facility . Password is normally needed
to do such actions.
Command Functional Group USIM and Phonebook Access
Command Format Query +CLCK=?
Response +CLCK: (list of supported s)
or
+CME ERROR:
Write Format +CLCK=,[,[,]]
Response OK
or
+CME ERROR:
when =2 and command successful:
+CLCK: [,
[+CLCK: ,
[...]]Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
values reserved by the present document:
"SC" SIM (lock SIM/UICC card) (SIM/UICC asks password in
MT power-up and when this lock Command issued)
"PN" Network Personalization (refer 3GPP TS 22.022)
"FD" SIM card or active application in the UICC (GSM or
USIM) fixed dialing memory feature
(if PIN2 authentication has not been done during the current
session, PIN2 is required as )
- 57 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
63/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
64/143
AT+CIMI Request IMSI
AT+CIMI Request IMSI
Command Function This command is used to obtain the International MobileSubscriber Identity (IMSI) value assigned to the SIM.
Command Functional Group Equipment Information
Command Format Query AT+CIMI=?
Response OK
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format AT+CIMI
Response 310260101xxxxx
OK
Parameter Values N/A
Reference GSM Ref. 07.07 Chapter 5.6
Standard Scope Optional
Enfora Implementation Scope Full
Notes Return value is manufacturer specific. The TA returns the
International Mobile Subscriber Identity (IMSI).
- 59 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
65/143
AT+CMOD Call mode
AT+CMOD Call mode
Command Function This command is used to select the type of call mode desired forfollowing dial (D) and/or answer (A) commands.
Command Functional Group Call Control
Command Format Query AT+CMOD=?
Response +CMOD: (0)
OK
Write Format AT+CMOD=
Response OK
Read Format AT+CMOD?
Response +CMOD: 0
OK
Execution Format N/A
Response N/A
Parameter Values
0 - Single service
Reference GSM Ref. 07.07 Chapter 6.4Standard Scope Mandatory
Enfora Implementation Scope Partial
Notes Default value will be 0. AT&F, restore factory defaults will reset
this value to 0.
- 60 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
66/143
AT+CPOL Preferred PLMN List
AT+CPOL Preferred PLMN List
Command Function This command is used for adding/deleting/updating thepreferred PLMN list. Also it is used for reading the all used
entries from the SIM/USIM list of preferred PLMNs.
Command Functional Group Registration (Mobility Management) AT commands
Command Format Query +CPOL=?
Response +CPOL: (list of supported s),(list of supported
s)
+CME ERROR:
Write Format +CPOL=[][, [,[, ,, ]]]
Response +CME ERROR:
Read Format +CPOL?
Response +CPOL: ,,[,,,]
[+CPOL: ,, [,,,]
[...]]
+CME ERROR:
Execution Format N/A
Response N/A
Parameter Values
integer type; the order number of operator in the SIM/USIM
preferred operator list
Note: Index value supported values is 1..MAX depends on the
SIM Capacity.
0 = long format alphanumeric
2 = numeric
Note: Only Numeric values are allowed when is setto 2.
string type; indicates if the format is alphanumeric
or numeric (see +COPS)
: GSM access technology:
0 = access technology not selected
- 61 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
67/143
1 =access technology selected
GSM compact access technology:
0 = access technology not selected
1 = access technology selected
UTRA access technology:
0 = access technology not selected
1 = access technology selected
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 62 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
68/143
AT+CNUM Subscriber Number
AT+CNUM Subscriber Number
Command Function AT+CNUM shall return strings of MSISDNs of the USIM whenexecuted
Command Functional Group USIM and Phonebook Access
Command Format Query N/A
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format +CNUM
Response +CNUM: [],, [+CNUM:
[],, ]
or
+CME ERROR:
Parameter Values
Optional alphanumeric string associated with ;
used character set should be the one selected with command
Select TE Character Set +CSCS String type phone number of format specified by
Type of phone number octet in integer format (refer TS
24.008 [8] subclause 10.5.4.7)
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples AT+CNUM+CNUM: "My Number","447411301666",145
OK
- 63 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
69/143
AT+COPN Read Operators Name
AT+COPN Read Operators Name
Command Function This command is used for reading all the operator names.Command Functional Group Registration (Mobility Management) AT commands
Command Format Query +COPN=?
Response N/A
Write Format N/A
Response N/A
Read Format N/A
Response N/A
Execution Format +COPN
Response +COPN: ,
[+COPN: ,
[...]]
+CME ERROR:
Parameter Values
string type; operator in numeric format
string type; operator in long alphanumeric format
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 64 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
70/143
AT+COPS PLMN Selection
AT+COPS PLMN Selection
Command Function This command is used for registering to a network either inautomatic/manual mode. Also it is used for reading the
current search mode and operator details.
Command Functional Group Registration (Mobility Management) AT commands
Command Format Query +COPS=?
Response +COPS: [list of supported (,long alphanumeric
,short alphanumeric ,numeric )s][,,(list
of supported s),(list of supported s)]
+CME ERROR:
Write Format +COPS=[[,[,]]]
Response +CMEERROR:
Read Format +COPS?
Response +COPS: [,, >[,]]
+CME ERROR:
Execution Format N/A
Response N/A
Parameter Values
0 = automatic ( field is ignored)1 = manual ( field shall be present, and
optionally)
3 = set only (for read command +COPS?), do not
attempt registration/ deregistration ( and
fields are ignored); this value is not applicable in read
command response
4 = manual/automatic ( field shall be present); if
manual selection fails, automatic mode (=0) is
entered
0 = long format alphanumeric
2 = numeric
string type; indicates if the format is alphanumeric
or numeric; long alphanumeric format can be upto 16
characters long and short format up to 8 characters (refer
- 65 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
71/143
GSM MoU SE.13); numeric format is the GSM Location Area
Identification number (refer 3GPP TS 24.008 subclause
10.5.1.3) which consists of a three BCD digit country code
coded as in ITU-T E.212 Annex A, plus a two BCD digit
network code, which is administration specific; returned shall not be in BCD format, but in IRA characters
converted from BCD; hence the number has structure:
(country code digit 3)(country code digit 2)(country code
digit 1)(network code digit 3)(network code digit 2)(network
code digit 1)
0 = unknown
1 = available
2 = current
3 = forbidden
Access technology selected
0 =GSM
1 = GSM Compact
2 = UTRAN
Reference
Standard Scope
Enfora Implementation Scope Full
Notes
Examples
- 66 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
72/143
AT+CPLS Selection of Preferred PLMN List
AT+CPLS Selection of Preferred PLMN List
Command Function This command is used for selecting/reading the preferredPLMN list type.
Command Functional Group Registration (Mobility Management) AT commands
Command Format Query +CPLS=?
Response +CPLS: (list of supported s)
+CME ERROR:
Write Format +CPLS=
Response +CME ERROR:
Read Format +CPLS?
Response +CPLS:
+CME ERROR:
Execution Format N/A
Response N/A
Parameter Values
0 = User controlled PLMN selector with Access Technology
EFPLMNwAcT
, if not found in the SIM/UICC then PLMN
preferred list EFPLMNsel
(this file is only available in SIM card
or GSM application selected in UICC)1 = Operator controlled PLMN selector with Access
Technology EFOPLMNwAcT
2 = HPLMN selector with Access Technology EFHPLMNwAcT
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 67 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
73/143
SMS Commands
AT+CMGC Send Command
AT+CMGC Send Command
Command Function Send Command
Command Functional Group SMS AT Commands
Command Format Query N/A
Response N/A
Write Format if PDU mode (+CMGF=0):
+CMGC=PDU is given
Response if PDU mode (+CMGF=0) and sending successful:
+CMGC:
if sending fails:
+CMS ERROR:
Read Format N/A
Response N/A
Execution Format N/A
Response N/AParameter Values
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 68 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
74/143
AT+CMGD Delete Message
AT+CMGD Delete Message
Command Function Delete MessageCommand Functional Group SMS AT Commands
Command Format Query +CMGD=?
Response +CMGD: (list of supported s)
Write Format +CMGD=
Response +CMS ERROR:
Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
Reference 3GPP TS 27.005 8.0.0
Standard Scope
Enfora Implementation Scope
Notes Execution command deletes message from preferred
message storage location
Examples
- 69 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
75/143
AT+CMGF Message Format
AT+CMGF Message Format
Command Function Message FormatCommand Functional Group SMS AT Commands
Command Format Query +CMGF=?
Response +CMGF: (list of supported s)
Write Format +CMGF=[]
Response
Read Format +CMGF?
Response +CMGF:
Execution Format N/A
Response N/A
Parameter Values
0 = PDU mode (default when implemented)
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 70 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
76/143
AT+CMGL List Messages
AT+CMGL List Messages
Command Function List MessagesCommand Functional Group SMS AT Commands
Command Format Query +CMGL=?
Response +CMGL: (list of supported s)
Write Format
Response
Read Format
Response
Execution Format +CMGL=[]
Response if PDU mode (+CMGF=0) and command successful:
+CMGL: ,,,
[+CMGL:,,,
[...]]
otherwise:
+CMS ERROR:
Parameter Values
: 0 "REC UNREAD" received unread message (i.e. new message)1 "REC READ" received read message
2 "STO UNSENT" stored unsent message (only applicable to SMs)
3 "STO SENT" stored sent message (only applicable to SMs)
4 "ALL" all messages (only applicable to +CMGL command)
Reference 3GPP TS 27.005 8.0.0
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 71 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
77/143
AT+CMGR Read Messages
AT+CMGR Read Messages
Command Function Read MessagesCommand Functional Group SMS AT Commands
Command Format Query +CMGR=?
Response
Write Format +CMGR=
Response if PDU mode (+CMGF=0) and command successful:
+CMGR: ,,
otherwise:
+CMS ERROR:
Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
Reference 3GPP TS 27.005 8.0.0
Standard Scope
Enfora Implementation Scope
Notes
Examples Execution command returns message with location value
from preferred message storage to the TE.
Status of the message and entire message data unit is
returned. If status of the message is 'received unread', status
in the storage changes to 'received read'. If reading fails,
final result code +CMS ERROR: is returned.
- 72 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
78/143
AT+CMGS Send Message
AT+CMGS Send Message
Command Function Send MessageCommand Functional Group SMS AT Commands
Command Format Query N/A
Response N/A
Write Format if PDU mode (+CMGF=0):
+CMGS=
PDU is given
Response if PDU mode (+CMGF=0) and sending successful:
+CMGS:
if sending fails:+CMS ERROR:
Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 73 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
79/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
80/143
AT+CMMS More Messages to Send
AT+CMMS More Messages to Send
Command Function More Messages to Send +CMMSCommand Functional Group SMS AT Commands
Command Format Query +CMMS=?
Response +CMMS: (list of supported s)
Write Format +CMMS=[]
Response
Read Format +CMMS?
Response +CMMS:
Execution Format N/A
Response N/A
Parameter Values
0 = disable
1 => keep enabled until the time between the response of
the latest message send command (+CMGS, +CMSS, etc.)
and the next send command exceeds 1-5 seconds (the exact
value is up to ME implementation), then ME shall close the
link and TA switches automatically back to 0
2 = enable (if the time between the response of the latestmessage send command and the next send command
exceeds 1-5 seconds (the exact value is up to ME
implementation), ME shall close the link but TA shall not
switch automatically back to =0)
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 75 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
81/143
AT+CMSS Send Message from Storage
AT+CMSS Send Message from Storage
Command Function Send Message from StorageCommand Functional Group SMS AT Commands
Command Format Query N/A
Response N/A
Write Format +CMSS=
Response if PDU mode (+CMGF=0) and sending successful:
+CMSS:
if sending fails:
+CMS ERROR:
Read Format N/A
Response N/A
Execution Format N/A
Response N/A
Parameter Values
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 76 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
82/143
AT+CNMA New Message Acknowledgement to ME/TA
AT+CNMA New Message Acknowledgement to ME/TA
Command Function New Message Acknowledgement to ME/TACommand Functional Group SMS AT Commands
Command Format Query +CNMA=?
Response if PDU mode (+CMGF=0):
+CNMA: (list of supported s)
Write Format N/A
Response N/A
Read Format N/A
Response N/AExecution Format if PDU mode (+CMGF=0):
+CNMA
Response +CMS ERROR:
Parameter Values
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 77 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
83/143
AT+CNMI New Message Indications to TE
AT+CNMI New Message Indications to TE
Command Function New Message Indications to TECommand Functional Group SMS AT Commands
Command Format Query +CNMI=?
Response +CNMI: (list of supported s),(list of supported
s),(list of supported s),(list of supported s),(list
of supported s)
Write Format +CNMI=[[,[,[,[,
]]]]]
Response +CMS ERROR:
Read Format +CNMI?
Response +CNMI: ,,,,
Execution Format N/A
Response N/A
Parameter Values
0 = Do not forward unsolicited result codes
3 = Forward unsolicited codes to accessory
0 = Disable SMS notification
1 = Enable unsolicited response for indication of incomingmessage in storage.
2 = Enable unsolicited response for incoming SMS message.
Disable broadcast SMS notification
0 = Disable SMS status reports
0 = Flush SU's result code buffer when is 3.
Reference
Standard Scope
Enfora Implementation ScopeNotes
Examples
- 78 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
84/143
AT+CPMS Preferred Message Storage
AT+CPMS Preferred Message Storage
Command Function Preferred Message StorageCommand Functional Group SMS AT Commands
Command Format Query +CPMS=?
Response +CPMS: (mem1),(mem1),(mem1)
Write Format +CPMS=mem1
Response +CPMS: ,
or
+CMS ERROR:
Read Format +CPMS?
Response +CPMS: mem1,,,mem1,
,,mem1,,
or
+CMS ERROR:
Execution Format N/A
Response N/A
Parameter Values
SM = SIM memory
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 79 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
85/143
AT+CSCA Service Center Address
AT+CSCA Service Center Address
Command Function Service Center AddressCommand Functional Group SMS AT Commands
Command Format Query N/A
Response N/A
Write Format +CSCA=[,]
Response OK or ERROR
Read Format +CSCA?
Response +CSCA: ,
Execution Format N/A
Response N/A
Parameter Values
Service Center Address
Type of Service Center Address
128 = Unknown
129 = National
145 = International
Reference
Standard Scope
Enfora Implementation Scope
Notes In PDU mode, setting is used by the same commands, but
only when the length of the SMSC address coded into
parameter equals zero.
Examples
- 80 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
86/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
87/143
GPRS Commands
AT+CGACT Activate/Deactivate PDP Context
AT+CGACT Activate/Deactivate PDP Context
Command Function The execution command is used to activate or deactivate the
specified PDP context (s). After the command has completed,
the MT remains in V.25ter command state. If any PDP
context is already in the requested state, the state for that
context remains unchanged. If the requested state for any
specified context cannot be achieved, an ERROR or +CME
ERROR response is returned. Extended error responses areenabled by the +CMEE command. If the MT is not PS
attached when the activation form of the command is
executed, the MT first performs a PS attach and then
attempts to activate the specified contexts. If the attach fails
then the MT responds with ERROR or, if extended error
responses are enabled, with the appropriate failure-to-
attach error message.
If no s are specified the activation form of the
command activates all defined contexts.
If no s are specified the deactivation form of thecommand deactivates all active contexts.
The read command returns the current activation states for
all the defined PDP contexts.
The test command is used for requesting information on the
supported PDP context activation states.
Command Functional Group Data Commands
Command Format Query +CGACT=?
Response +CGACT: (list of supported s)
Write Format +CGACT= [,[,[,]]]
Response OK or ERROR
Read Format +CGACT?
Response +CGACT: ,
[+CGACT: , [...]]
- 82 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
88/143
Execution Format N/A
Response N/A
Parameter Values
indicates the state of PDP context activation0 = deactivated
1 = activated
Other values are reserved and will result in an ERROR
response to the execution command. It is a mandatory
parameter.
a numeric parameter which specifies a particular PDP
context definition (see +CGDCONT command).
Note: The AT parser will verify the existence of the
mandatory field and also check its validity. If
is absent or its validity check fails, then AT parser will return
ERROR right away.
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 83 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
89/143
AT+CGATT PS Attach or Detach
AT+CGATT PS Attach or Detach
Command Function The execution command is used to attach the MT to, ordetach the MT from, the Packet Domain service. After the
command has completed, the MT remains in V.25ter
command state. If the MT is already in the requested state,
the command is ignored and the OK response is returned.
If the requested state cannot be achieved, an ERROR or
+CME ERROR response is returned. Extended error
responses are enabled by the +CMEE command.
Any active PDP contexts will be automatically deactivated
when the attachment state changes to detached.
The read command returns the current Packet Domainservice state.
The test command is used for requesting information on the
supported Packet Domain service states.
Command Functional Group Data Commands
Command Format Query +CGATT=?
Response +CGATT: (list of supported s)
Write Format +CGATT=
Response OK or ERROR
Read Format +CGATT?
Response +CGATT:
Execution Format N/A
Response N/A
Parameter Values
indicates the state of PS attachment 0 - detached 1 -
attached Other values are reserved and will result in an
ERROR response to the execution command.
Reference
Standard Scope
Enfora Implementation Scope
Notes The AT parser will verify the existence of the mandatory
field in the above AT command. And it will also
- 84 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
90/143
validate the value for .
If the mandatory field is absent or, if its value is
anything other than 0 or 1, AT parser will return ERROR right
away.
Examples
- 85 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
91/143
AT+CGCLASS GPRS Mobile Station Class
AT+CGCLASS GPRS Mobile Station Class
Command Function This command is used for setting/reading the GPRS mobileclass.
Command Functional Group Registration (Mobility Management) AT commands
Command Format Query +CGCLASS=?
Response +CGCLASS: (list of supported s)
Write Format +CGCLASS= []
Response OK or ERROR
Read Format +CGCLASS?
Response +CGCLASS: Execution Format N/A
Response N/A
Parameter Values
A string parameter which indicates the mode of operation B
- Class-B mode of operation (A/Gb mode), (not applicable in
Iu mode)
Reference
Standard Scope
Enfora Implementation Scope
Notes The UTM0108 shall use Hard coded value as Class-B
Examples
- 86 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
92/143
AT+CGDCONT Define PDP Context
AT+CGDCONT Define PDP Context
Command Function Specifies PDP context parameter values for a PDP contextidentified by the (local) context identification parameter, .
Command Functional Group GPRS Commands
Command Format Query AT+CGDCONT=?
Response +CGDCONT: (1-6),IP,,,(0,1),(0,1)
OK
Write Format AT+CGDCONT=,,
Response ,,,
OK
Read Format AT+CGDCONT?
Response +CGDCONT: ,,,, ,
OK
Execution Format N/A
Response N/A
Parameter Values
PDP Context Identifier a numeric parameter which specifies a
particular PDP context definition. The parameter is local to the
TE-MT interface and is used in other PDP context-related
commands. The range of permitted values (minimum value = 1) is
returned by the test form of the command.
IP
Access Point Name Identifies the MT in the address space
- 87 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
93/143
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
94/143
AT+CGEQMIN Minimum Quality of Service Profile
AT+CGEQMIN 3G Minimum Quality of Service Profile
Command Function This command allows the TE to specify a minimumacceptable profile, which is checked by the MT against the
negotiated profile returned in the Activate/Modify PDP
Context Accept message.
The set command specifies a profile for the context
identified by the (local) context identification parameter,
. The specified profile will be stored in the MT and
checked against the negotiated profile only at activation or
MS-initiated modification of the related context. Since this is
the same parameter that is used in the +CGDCONT
command, the +CGEQMIN command is effectively anextension to these commands. The QoS profile consists of a
number of parameters, each of which may be set to a
separate value.
A special form of the set command, +CGEQMIN=
causes the minimum acceptable profile for context number
to become undefined. In this case no check is made
against the negotiated profile.
The read command returns the current settings for each
defined context.
The test command returns values supported as a compoundvalue. If the MT supports several PDP types, the parameter
value ranges for each PDP type are returned on a separate
line.
Command Functional Group Data Commands
Command Format Query +CGEQMIN=?
Response +CGEQMIN: , (list of supported s)
,(list of supported s) ,(list of
supported s), (list of supported
s), (list of supported s) ,(list of supported s) ,(list of
supported s) ,(list of supported s) ,(list of supported s)
,(list of supported s) ,(list of
supported s) ,(list of supported
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
95/143
handling priority>s)
[+CGEQMIN: , (list of supported
s) ,(list of supported s),
(list of supported s) ,(list of supported
s), (list of supported s) ,(list of supported s) ,(list of
supported s) ,(list of supported s) ,(list of supported s)
,(list of supported s) ,(list of
supported s) ,(list of supported s) []]
Write Format +CGEQMIN=[ [, [,
[, [,
[, [, [, [, [,
[, [, [,]]]]]]]]]]]]]
Response OK or ERROR
Read Format +CGEQMIN?
Response +CGEQMIN: , ,,
,
,, , , ,
, , ,
[+CGEQMIN: , , , , ,, , , ,
, , ,
[]]
Execution Format N/A
Response N/A
Parameter Values
a numeric parameter which specifies a particular PDP
context definition (see +CGDCONT command).
- 90 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
96/143
a numeric parameter that indicates the type of application
for which the UMTS bearer service is optimized.
0 = conversational
1 = streaming
2 = interactive3 = background
Other values are reserved.
a numeric parameter that indicates the maximum number
of kbits/s delivered to UMTS (up-link traffic) at a SAP. As an
example a bitrate of 32kbit/s would be specified as '32' (e.g.
AT+CGEQMIN=,32, ) (refer TS 24.008 [8] subclause
10.5.6.5).
a numeric parameter that indicates the maximum number
of kbits/s delivered by UMTS (down-link traffic) at a SAP. Asan example a bitrate of 32kbit/s would be specified as '32'
(e.g. AT+CGEQMIN=,32, ) (refer TS 24.008 [8] subclause
10.5.6.5).
a numeric parameter that indicates the guaranteed number
of kbits/s delivered to UMTS (up-link traffic) at a SAP
(provided that there is data to deliver). As an example a
bitrate of 32kbit/s would be specified as '32' (e.g.
AT+CGEQMIN=,32, ) (refer TS 24.008 [8] subclause
10.5.6.5).
a numeric parameter that indicates the guaranteed number
of kbits/s delivered by UMTS (down-link traffic) at a SAP
(provided that there is data to deliver). As an example a
bitrate of 32kbit/s would be specified as '32' (e.g.
AT+CGEQMIN=,32, ) (refer TS 24.008 [8] subclause
10.5.6.5).
a numeric parameter that indicates whether the UMTS
bearer shall provide in-sequence SDU delivery or not.
0 = no
1 = yesOther values are reserved.
a numeric parameter (1,2,3,) that indicates the maximum
allowed SDU size in octets (refer TS 24.008 [8] subclause
10.5.6.5).
- 91 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
97/143
a str ing parameter that indicates the target value for the
fraction of SDUs lost or detected as erroneous. SDU error
ratio is defined only for conforming traffic. The value is
specified as 'mEe'. As an example a target SDU error ratio of
510-3 would be specified as '5E3' (e.g.AT+CGEQMIN=,5E3,) (refer TS 24.008 [8] subclause
10.5.6.5).
a string parameter that indicates the target value for the
undetected bit error ratio in the delivered SDUs. If no error
detection is requested, Residual bit error ratio indicates the
bit error ratio in the delivered SDUs. The value is specified as
'mEe'. As an example a target residual bit error ratio of
510-3 would be specified as '5E3' (e.g.
AT+CGEQMIN=,5E3,) (refer TS 24.008 [8] subclause10.5.6.5).
a numeric parameter that indicates whether SDUs detected
as erroneous shall be delivered or not.
0 = no
1 = yes
2 = no detect
Other values are reserved.
a numeric parameter (0,1,2,) that indicates the targeted
time between request to transfer an SDU at one SAP to its
delivery at the other SAP, in milliseconds (refer TS 24.008 [8]
subclause 10.5.6.5).
a numeric parameter (1,2,3,) that specifies the relative
importance for handling of all SDUs belonging to the UMTS
bearer compared to the SDUs of other bearers (refer TS
24.008 [8] subclause 10.5.6.5).
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 92 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
98/143
AT+CGEQREQ 3G Quality of Service
AT+CGEQREQ 3G Quality of Service
Command Function This command allows the TE to specify a UMTS Quality of Service Profile that is used when the MT sends an Activate
PDP Context Request message to the network.
The set command specifies a profile for the context
identified by the (local) context identification parameter,
. The specified profile will be stored in the MT and sent
to the network only at activation or MS-initiated
modification of the related context. Since this is the same
parameter that is used in the +CGDCONT command, the
+CGEQREQ command is effectively an extension to these
commands. The QoS profile consists of a number ofparameters, each of which may be set to a separate value.
A special form of the set command, +CGEQREQ=
causes the requested profile for context number to
become undefined. The read command returns the current
settings for each defined context.
The test command returns values supported as a compound
value. If the MT supports several PDP types, the parameter
value ranges for each PDP type are returned on a separate
line.
Command Functional Group Data Commands
Command Format Query +CGEQREQ=?
Response +CGEQREQ: , (list of supported s)
,(list of supported s), (list of
supported s), (list of supported
s), (list of supported s),(list of supported s) ,(list of
supported s) ,(list of supported s) ,(list of supported s)
,(list of supported s) ,(list of
supported s) ,(list of supported s)
[+CGEQREQ: , (list of supported
s) ,(list of supported s),
(list of supported s), (list of supported
- 93 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
99/143
s), (list of supported s),(list of supported s) ,(list of
supported s) ,(list of supported s) ,(list of supported s)
,(list of supported s) ,(list ofsupported s) ,(list of supported s)
[]]
Write Format +CGEQREQ=[ [, [,
[, [,
[, [, [, [, [,
[, [, [, ]]]]]]]]]]]]]
Response OK or ERROR
Read Format +CGEQREQ?
Response +CGEQREQ: , ,
, ,
, , , , ,
, , ,
[+CGEQREQ: , , , , , , , , ,
, , ,
[]]
Execution Format N/A
Response N/A
Parameter Values
a numeric parameter which specifies a particular PDP
context definition (see +CGDCONT command).
a numeric parameter that indicates the type of application
for which the UMTS bearer service is optimized.
0 = conversational
- 94 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
100/143
1 = streaming
2 = interactive
3 = background
4 = subscribed value
If the Traffic class is specified as conversational orstreaming, then the Guaranteed and Maximum bitrate
parameters should also be provided. Other values are
reserved.
a numeric parameter that indicates the maximum number
of kbits/s delivered to UMTS (up-link traffic) at a SAP. As an
example a bitrate of 32kbit/s would be specified as '32' (e.g.
AT+CGEQREQ=,32, ). This parameter should be provided
if the Traffic class is specified as conversational or streaming
(refer TS 24.008 subclause 10.5.6.5).
a numeric parameter that indicates the maximum number
of kbits/s delivered by UMTS (down-link traffic) at a SAP. As
an example a bitrate of 32kbit/s would be specified as '32'
(e.g. AT+CGEQREQ=,32, ). If the parameter is set to '0'
the subscribed value will be requested. This parameter
should be provided if the Traffic class is specified as
conversational or streaming (refer TS 24.008 [8] subclause
10.5.6.5).
a numeric parameter that indicates the guaranteed number
of kbits/s delivered to UMTS (up-link traffic) at a SAP
(provided that there is data to deliver). As an example a
bitrate of 32kbit/s would be specified as '32' (e.g.
AT+CGEQREQ=,32, ). If the parameter is set to '0' the
subscribed value will be requested. This parameter should be
provided if the Traffic class is specified as conversational or
streaming (refer TS 24.008 [8] subclause 10.5.6.5).
a numeric parameter that indicates the guaranteed number
of kbits/s delivered by UMTS (down-link traffic) at a SAP
(provided that there is data to deliver). As an example abitrate of 32kbit/s would be specified as '32' (e.g.
AT+CGEQREQ=,32, ). If the parameter is set to '0' the
subscribed value will be requested. This parameter should be
provided if the Traffic class is specified as conversational or
streaming (refer TS 24.008 subclause 10.5.6.5).
- 95 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
101/143
a numeric parameter that indicates whether the UMTS
bearer shall provide in-sequence SDU delivery or not.
0 = no
1 = yes
2 = subscribed value.Other values are reserved.
a numeric parameter (1,2,3,) that indicates the maximum
allowed SDU size in octets. If the parameter is set to '0' the
subscribed value will be requested (refer TS 24.008
subclause 10.5.6.5).
a str ing parameter that indicates the target value for the
fraction of SDUs lost or detected as erroneous. SDU error
ratio is defined only for conforming traffic. The value is
specified as 'mEe'. As an example a target SDU error ratio of510-3 would be specified as '5E3' (e.g.
AT+CGEQREQ=,5E3,). '0E0' means subscribed value
(refer TS 24.008 subclause 10.5.6.5).
a string parameter that indicates the target value for the
undetected bit error ratio in the delivered SDUs. If no error
detection is requested, Residual bit error ratio indicates the
bit error ratio in the delivered SDUs. The value is specified as
'mEe'. As an example a target residual bit error ratio of
510-3 would be specified as '5E3' (e.g.
AT+CGEQREQ=,5E3,). '0E0' means subscribed value
(refer TS 24.008 subclause 10.5.6.5).
a numeric parameter that indicates whether SDUs detected
as erroneous shall be delivered or not.
0 = no
1 = yes
2 = no detect
3 = subscribed value
Other values are reserved.
a numeric parameter (0,1,2,) that indicates the targetedtime between request to transfer an SDU at one SAP to its
delivery at the other SAP, in milliseconds. If the parameter is
set to '0' the subscribed value will be requested (refer TS
24.008 [8] subclause 10.5.6.5).
- 96 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
102/143
a numeric parameter (1,2,3,) that specifies the relative
importance for handling of all SDUs belonging to the UMTS
bearer compared to the SDUs of other bearers. If the
parameter is set to '0' the subscribed value will be requested
(refer TS 24.008 subclause 10.5.6.5).
Reference
Standard Scope
Enfora Implementation Scope
Notes
Examples
- 97 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
103/143
AT+CGEREP Packet Domain Event Reporting
AT+CGEREP Packet Domain Event Reporting
Command Function The PC Client will send the set or get operation forAT+CGEREP to the AT parser. The set version of this AT
command is used to enable or disable sending of unsolicited
result codes, +CGEV: XXX from MT to TE in the case of
certain events occurring in the Packet Domain MT or the
network. And the get or read version of the command is used
to return the current mode and buffer settings.
Command Functional Group Data Commands
Command Format Query +CGEREP=?
Response +CGEREP: (list of supported s),(list of supporteds)
Write Format +CGEREP=[[,]]
Response OK or ERROR
Read Format +CGEREP?
Response +CGEREP: ,
Execution Format N/A
Response N/A
Parameter Values AT parser will support only the value 1 for .
1 = discard unsolicited result codes when MT-TE link is
reserved (e.g. in on-line data mode); otherwise forward
them directly to the TE
The value indicates how the MT buffer will be treated. AT
parser will ignore this parameter.
0 = MT buffer of unsolicited result codes defined within this
command is cleared when 1 or 2 is entered
1 = MT buffer of unsolicited result codes defined within this
command is flushed to the TE when 1 or 2 is
entered (OK response shall be given before flushing the
codes)
Reference
Standard Scope
- 98 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual - Rev 1_00.pdf
104/143
Enfora Implementation Scope
Notes Currently AT parser will support only one type of event
reporting: NW DEACT (Network Initiated Deactivation).
Supported events:In case the AT parser receives the asynchronous event
Deactivate Indication initiated from the network, the AT
parser will send the unsolicited result codes of the AT+CGEV
command to the terminal to notify as follows:
+CGEV: NW DEACT , , []
The network has forced a context deactivation. The
that was used to activate the context is provided if known to
the MT.
Examples
- 99 -
-
8/11/2019 UMT0108AT001 - Enfora Enabler HS 1000 - AT Command Manual -