verdermag global
TRANSCRIPT
Verdermag Global Mag Drive Centrifugal Pumps | 3
Verdermag Global
Verdermag Global metallic mag drives can be used for a wide range of applications. The range covers flow rates from 1-200 m3/h, with possible temperature from -100 to +250 °C. Operating pressures of 16 to 300 bar. Special mag drive pumps with specifications beyond these parameters are available on request. The Verdermag Global mag drive pumps are hermetically sealed and therefore 100% leak free.
Features and advantages Zero leakage (100% leak free) No mechanical seals or packed glands No external flushing systems Ensure a clean and safe operating environment, highly efficient
Close coupled design No alignment required Increased mean time between maintenance
Verdermag Global metallic centrifugal pumps are synchronous magnet-driven seal-less pumps.
The Verdermag Global is a range of pumps with utmost flexibility. These magnetic driven pumps
are ideally suited to modern and heavy duty requirements.
LeakproofVerdermag mag drive pumps have no glands, no seals nor valves. In contrast to sealed centrifugal pumps, the magnet capsule of the Verdermag mag drive pump ensures a safe and leak free operation. Even under heavy-duty circumstances the pumps are extremely reliable.
Working principle
A magnetic coupling consists of two magnet assemblies. One is the outer assembly (the drive magnet) and the other is the inner assembly (the driven magnet). The outer assembly is connected to a motor and the inner assembly is directly attached to the pump impeller. As illustrated, at rest, the magnet components of the outer assembly are aligned with their counterparts in the inner assembly.
When load (torque) is applied, the coupling deflects angularly and the magnets create a force of simultaneous attraction and repulsion. This force is used to transfer torque from the motor to the impeller. Verdermag mag drive pumps are therefore sealless and pumps are hermetically sealed.
No slippage, no induction currentsThe permanent magnet coupling in the Verdermag mag drive centrifugal pump causes neither slippage nor induction currents during rotation. If excessive torque is applied, the magnets will de-couple. The magnets will not re-couple unless the pump is stopped. There is no energy loss in a permanent coupling unless an electrically conductive containment is placed between the outer and inner magnets.
If an electrically conductive material is used for the containment, eddy-currents will be generated which will cause some energy loss. Verdermag mag drives use no conductive materials and therefore have no or only small eddy current losses.
And what about the working principle of the metallic mag drive pumps?In addition to the above, the Verdermag metallic magnetic driven pumps utilise the differential pressure generated by the pumping action to create a flow around the bearings and magnets. The pumped liquid acts as a cooling medium to dissipate the heat generated from eddy currents as the magnets pass around the containment shell.
It is also used to lubricate the hydrodynamic bearing sets, with flow from the front bearing passing through the balance holes of the impeller and flow around the rear bearing re-entering the low pressure suction area of the volute.
N
S
S
N
S
N
N
S
S
N
N
S
N
S
S
N
NS
S
N
SN
N
S
S
N N
S
N
SS
N
NS
S
N
S N
N
S
NS
S
N
SN
N
S
SN
N
S
NS
S
N
NS
S
N
S N
N
S
SN
N
S
N S
S
N
NS
S
N
SN
N
S
Verdermag Global Mag Drive Centrifugal Pumps | 5
The Style 1 Verdermag Global drive pumps have
flows up to 25 m3/h and differential heads up to
40 m. The Style 1 Global centrifugal pumps offer
a low-cost option for low flow and head duties.
The pumps are available from stock.
This range of Mag Drive pumps is suitable for lower duties than covered by the ISO 2858 (Mll) pumps. They offer a low cost option for more flow and head duties and are available from stock. Style 1 pumps are also suitable for applications where crystallisation is problematic as the mag drive prevents air contact and so no crystallisation occurs.
GLOBAL MODEL STyLE 1
Type D1 D2 A C H1 H2 M1 M2 H
125M 40 25 62 120 139 125 93 141 184/194
160L 40 25 66,5 130 139 150 93 141 165/175
160M 40 25 66,5 130 139 150 93 141 165/175
0.00
2.00
4.00
6.00
8.00
10.00
12.00
5.00 15.00
Hea
d (m
)
(m3/h)
160M 160L
125M
0.00
5.00
10.00
15.00
20.00
25.00
30.00
35.00
40.00
45.00
0.00 10.00 20.00 30.00
Hea
d (m
)
(m3/h)
160M160L
125M
Features and advantages Hydraulic pump end with investment casing and fabricated casing bowls with centreline discharge
Single bearing design for increased reliability High level of interchangeability for spare parts Optional: Universal, PN16 or ANSI 150.ib. flanges Close coupled motor fitment, no need for re-alignment after servicing
ATEX certified models available
165
A
H2
F
H1
230
AD
D1
D2KK CABLE ENTRY
4 HOLES TO SUIT M12
M1
M2
C
L
165
A
H2
F
H1
230
AD
D1
D2KK CABLE ENTRY
4 HOLES TO SUIT M12
M1
M2
C
L
GLOBAL MODEL MII
The Verdermag Global MII style pumps offer
medium to high flow and head. With Flows
up to 200 m3/h and differential heads of
up to 100 m. This series of Global pumps
can also be made on request with a high
temperature operation.
The Mark ll range of Mag drive pumps are suitable for the transfer of heat or cooling whilst operating at extreme temperatures. The range is ISO 2858 standard pumps which offer a medium to high flow and head duties. The majority of the pumps in the mark ll range are available for assembly from stock components allowing a quick and efficient delivery.
Features and advantages According to ISO 2858 Twin bearing design for superior operation Modular design: high interchangeability of spare parts Alternative joints and elastomers are available Casing can be supplied with PN16 Close coupled motor fitment, no need for re-alignment after servicing
Thermocouple probe connection to back plate to permit bearing temperature to be monitored. This can also be mounted
Heating/cooling jackets to back plate and/or casing (Modification is possible)
ATEX certified models available
Drive Size F2 H3 M3 S2 W
C3-112 171 132 65 M12 124
C3-132 191 160 65 M12 124
C6-132 224 160 80 M16 164
C6-180 254 180 80 M16 164
D6-180 254 180 80 M16 164
L, AD and KK depending on motor frame size.
AF1
H2
H1
L
M1
F2
KK CABLE ENTRY
H3
AD
W
N1
M2
N2
N4
C4 - TO SUIT S12 - TO SUIT S2 X N3 CRS
Verdermag Global Mag Drive Centrifugal Pumps | 7
Type D1 D2 A C F1 H1 H2 M1 M2 N1 N2 S1
100-65-200 100 65 100 52.5 97.5 180 225 125 95 320 250 M12
100-65-250 100 65 125 65 92.5 200 250 160 120 360 280 M12
100-80-125 100 80 100 52.5 73.5 160 180 125 95 280 212 M12
100-80-160 100 80 100 52.5 86 160 200 125 95 280 212 M12
125-100-160 125 100 125 65 86 200 250 160 120 360 280 M16
125-100-200 125 100 125 65 98.5 200 280 160 120 360 280 M16
50-32-125 50 32 80 45 73.5 112 140 100 70 190 140 M12
50-32-160 50 32 80 45 71.5 132 160 100 70 240 190 M12
50-32-200 50 32 80 45 89.5 160 180 100 70 240 190 M12
50-32-250 50 32 100 52.5 92.5 180 225 125 95 320 250 M12
65-40-200 65 40 100 65 89.5 160 180 100 70 265 212 M12
65-40-250 65 40 100 52.5 92.5 180 225 125 95 320 250 M12
65-50-125 65 50 80 45 73.5 112 140 100 70 210 160 M12
65-50-160 65 50 80 45 77 132 160 100 70 240 190 M12
80-50-200 80 50 100 65 89.5 160 200 100 70 265 212 M12
80-50-250 80 50 125 77.5 92.5 180 225 125 95 320 250 M12
80-65-125 80 65 100 65 73.5 132 160 100 70 240 190 M12
80-65-160 80 65 100 65 77 160 180 100 70 265 212 M12
2. 5 5 7. 5 1 0 15 20 30 40 100 150
Q (m 3 /h)
H ea
d (m
)
0
5
10
15
20
25
30
50- 32- 125 65- 50- 125 80- 65- 125
100- 80- 125
50- 32- 160 65- 50- 160 80- 65- 160
100- 80- 16 0
125- 100- 200
125- 100- 160
50- 32- 200 65- 40 -2 00
100- 65- 20 0
125- 100- 200
50- 32- 250 65- 40- 250
80- 50- 250
100- 65- 250
MII (1450 rpm) 4 pole 50Hz
5 7.5 10 15 20 30 40 10 0 150 200 300
Q (m 3 /h)
H ea
d (m
)
50- 32- 125
65- 50- 125
80- 65- 125
100- 80- 125
50- 32- 160 65- 50- 160
80- 65- 160
100- 80- 160
125- 100- 160
50- 32- 200
65- 40- 200
80- 50- 200
100- 65- 200
125- 100- 200
50- 32- 250
65- 40- 25 0
80- 50- 250 100- 65- 250
0
20
40
60
80
100
120 MII pumps (2900 rpm) 2 pole 50Hz
AF1
H2
H1
L
M1
F2
KK CABLE ENTRY
H3
AD
W
N1
M2
N2
N4
C4 - TO SUIT S12 - TO SUIT S2 X N3 CRS
AF1
H2
H1
L
M1
F2
KK CABLE ENTRY
H3
AD
W
N1
M2
N2
N4
C4 - TO SUIT S12 - TO SUIT S2 X N3 CRS
GLOBAL MODEL HSP
The HSP range of pumps provide the optimum
solution for high system pressure applications
where 100% containment of the process liquid is
essential. Available with pressure ratings up-to
200 BarG the HSP range can be supplied to suit
the most demanding operating conditions.
The HSP mag drive range is particularly effective in applications where chemicals are pumped at high pressures. Samples can be tapped off the main line and pumped through a densitometer/sample extractor.
Features and advantages Hydraulic pump end with standard casing and fabricated casting bowls with centreline discharge/castings now possible on the same models
Single bearing design for increased reliability High level of interchangeability for spare parts Customer requirements for testing or coatings 3.1 material certificates available ATEX certified models available
Drive Size C F2 H1 M1 M2 N1 N2 S
B1-080 24 150 139 130 93 230 165 M12
B3-090 24 150 139 130 93 230 165 M12
B3-11 24 165 139 145 115 230 165 M12
C3-11 13 180 180 180 130 245 195 M12
C3-13 13 200 180 180 130 245 195 M12
C6-13 33 240 180 220 170 245 195 M12
C6-180 33 270 180 220 170 245 195 M12
L, AD, KK are depending on motor frame size and motor brand.
H2
A F1
D2
D1
KK CABLEENTRY
4 HOLES TO SUIT M12
M2
M1
F2
C
L
N2
N1
H1
AD
Verdermag Global Mag Drive Centrifugal Pumps | 9
Type D1 D2 A A F1 H2 H2 Flanged version Studded version Flanged version Studded version
25-25-100 25 25 165 110 34 175 110
25-25-125 25 25 165 110 34 187 110
25-25-160 25 25 170 110 64 206 135
25-25-200 25 25 170 110 64 230 165
25-25-250 25 25 110 64 180
40-25-100 40 25 165 110 34 175 110
40-25-125 40 25 165 110 34 187 110
40-25-160 40 25 170 110 64 206 135
40-25-200 40 25 170 110 64 230 165
40-25-250 41 26 110 64 180
50-40-125 50 40 165 110 34 187 110
50-40-160 50 40 170 110 64 206 135
50-40-200 50 40 170 110 64 230 165
50-40-250 50 40 110 64 180
80-50-125 80 50 200 38 206
80-50-160 80 50 205 68 225
80-50-200 80 50 205 68 249
25 - 25 - 10 0
25 - 25 - 12 5
25 - 25 - 16 0
25 - 25 - 20 0
25 - 25 - 25 0
40 - 25 - 10 0
40 - 25 - 12 5
40 - 25 - 16 0
40 - 25 - 20 0
40 - 25 - 25 0
50 - 40 - 12 5
50 - 40 - 16 0
50 - 40 - 20 0
50 - 40 - 25 0
80 - 50 - 12 5
80 - 50 - 16 0
80 - 50 - 20 0
0
5
10
15
20
25
30
1 2 .5 5 7 .5 10
Q (m 3 /h)
H (m
)
15 20 30 40
HSP pumps (1450 rpm) 4 pole 50Hz
1 2 .5 5 7 .5 10 15 20 30 40 0
20
40
60
80
100
120
25- 25- 100
25- 25- 125
25- 25- 160
25- 25- 200
25- 25- 250
40- 25- 100
40- 25- 125
40- 25- 160
40- 25- 200
40- 25- 250
50- 40- 125
50- 40- 160
50- 40- 200
50- 40- 250
80- 50 -1 25
80- 50 -1 60
80- 50 -2 00
100
Q (m 3 /h)
H ea
d (m
)
HSP pumps (2900 rpm) 2 pole 50Hz
H2
A F1
D2
D1
KK CABLEENTRY
4 HOLES TO SUIT M12
M2
M1
F2
C
L
N2
N1
H1
AD
Organisation
Verdermag Global provides pumping solutions to a wide range of industries including: Chemical Petrochemical Pharmaceutical
All these industries require a method for transferring fl uid from one location to another and Verdermag Global has a pump type suitable for all your pumping need. The Global range is mainly suited to the chemical industry and are highly suitable for the transfer and circulation of aggressive chemicals where leak free containment is essential.
International presenceThe Verdermag Global pump range has a worldwide networkof distributors which include:
Austria, China, Czech Republic, Denmark, France, Germany,Hungry, Ireland, Norway, Poland, Romania, Russia, Spain,Sweden, Switzerland and Turkey.
Contact Verdermag GlobalIf you would like to know more about our pumping solutions then please visit our website www.verderglobal.com. You will fi nd thefull range of our pumps as well as application stories, latest newsand the contact details for our worldwide distributors.Alternatively you can contact head offi ce on:Tel +44 (0113) 222 0250Fax +44 (0113) 246 5649Mail [email protected]
Any questions? You may still have questions and/or comments after reading
this brochure. Please feel free to contact us on +44 (0)113 222 0250. You can
also respond via email to [email protected]. For more information about
Verdermag Global please visit our website www.verderglobal.com
VERDERMAG GLOBAL
Whitehouse Street
Leeds, LS10 1AD
United Kingdom
TEL +44 (0)113 222 0250
FAX +44 (0)113 246 5649
MAIL [email protected]
WEB www.verderglobal.com
01-0
6-20
10-V
Mgl
-REV
-01
AT Wien BE Aartselaar CH Basel CN Shanghai CZ Praha DE Haan
FR Eragny s/Oise GB Leeds HU Budapest IT Torre Boldone JP Tokyo
NL Groningen/Vleuten PL Katowice RO Bucuresti/Sibiu SK Bratislava
US Newtown/Macon ZA Northriding