viking sg series double pumps (with shaft seal)vp.salesmrc.com/pdfs/sec_341.2.pdf · viking pump a...

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

Section 341.2Page 341.2.1Issue C

SERIES SG-04, -05, -07 (Cast Iron) SGN-05, -07 (Ductile Iron)

VIKING SG SERIES DOUBLE PUMPS (WITH SHAFT SEAL)

OPERATING RANGE:

SERIES SG-07

SERIES SG-04/-05

SG Pumps (Cast Iron, Lip or Mechanical Sealed)Displacement Combinations No. 70

Flow Range (Per Section)

GPM 0.06 to 16 / SectionM3/Hr 0.011 to 3.0 / Section

Pressure Range

PSI to 500 Continuous, 2,500 Intermittent

Bar to 34 Continuous, 170 Intermittent

Temperature Range

°F -40° to +450°°C -40° to +230°

Viscosity Range

SSU 28 to 1,000,000cSt 0.1 to 250,000

SGN Pumps (Ductile Iron, Lip or Mechanical Sealed)Displacement Combinations

No. 49

Flow Range GPM 0.7 to 16 / SectionM3/Hr 0.16 to 3.0 / Section

Pressure Range

PSI to 500 Continuous, 2,500 Intermittent

Bar to 34 Continuous, 170 Intermittent

Temperature Range

°F -40° to +450°°C -40° to +230°

Viscosity Range

SSU 28 to 1,000,000cSt 0.1 to 250,000





Viking SG-04, -05 and -07 Double Pumps allow two independent pumping units to be operated from a single power source to reduce equipment costs and simplify installation. System flexibility is maintained as each pumping unit can be operated at a different pressure without affecting the other. SG-10 and -14 Double Pumps are available, but not as standard product, contact factory.

Standard configuration is with separate suction and discharge ports for each section. A sleeve bearing (bushing) limits fluid flow between sections, but if two separate liquids are pumped, some mixing of liquids is to be expected. Where both liquids cannot

contact each other (such as reactive polyurethane foam components) custom pumps with seals between sections are available (contact factory). Optional configurations include a common suction port and separate discharge ports (to split one liquid source into two flow streams), or separate suction ports and a common discharge port (to blend two liquids).

These pumps are NOT furnished with pressure relief valves as standard. Some form of overpressure protection must be provided for the system (e.g. relief valve in discharge line, torque limiting device, rupture disks, etc.

MODEL NUMBER KEY

SERIES DESCRIPTION

SGN - 051825 - G 0 - BDrive Equipment B = Foot-Bracket Mounted D = Base Mounted Direct Drive M = Face Mounted Motor Drive

Pump Size Design Series

Shaft Rotation (Viewed from shaft end) 0 = Clockwise 1 = Counter Clockwise (optional)

Spur Gear Principle

Material of ConstructionBlank = Cast Iron N = Ductile Iron

SERIES SG-04 AND SG-05 — 90° POSITIONING SERIES SG-07 — 180° POSITIONING

Pump can be mounted in any of four 90° positions, giving the option of horizontal or vertical porting. Arrow shows direction of motor rotation as clockwise, looking from shaft end. Ports are not on shaft centerline, so inverting will result in different port locations.

Clockwise pump can be mounted in either of two positions to obtain suction on right or left hand side. Offers 90° positioning with “M” drive. Ports are not on shaft centerline, so inverting will result in different port locations.


Section 341.241.2.3Issue C



PUMP CONSTRUCTION AND FEATURES

Sealing options include lip seal or component

mechanical seal. Mag Drive available,

but not standard.

Motor speed operation with options for foot mount, NEMA motor mount or IEC motor mount

Combining two pumps in one eliminates an extra motor, while providing application specific solutions.

Anti-friction needle bearings standard for long life. Options for carbon graphite or silicon carbide bushings.

Hardened steel gears and shafts for long lifeOptions for

different flow rates per section

Option for split inlet / common discharge to mix two liquids in constant proportions.

SEPARATE SUCTION, COMMON DISCHARGE PORT

OPTIONAL

Separate inlet and discharge ports standard to pump two liquids or use one section for scavenge, one for pumping.

SEPARATE SUCTION & DISCHARGE PORTS

STANDARD

Option for common inlet / split discharge to split flows to two applications.

COMMON SUCTION, SEPARATE DISCHARGE PORTS

OPTIONAL





Viton® and Kalrez® are registered trademarks of DuPont Performance Elastomers

COMPONENT IDENTIFICATION

BRACKET, LIP SEAL& NEEDLE BEARINGS

ASSEMBLY

DOWELPINS

DOWELPINS

O-RING

O-RING

O-RING

O-RING

DRIVESHAFT

DRIVENSHAFT

KEYS & BALLS

MATCH GROUNDCASING & GEARS

MATCH GROUNDCASING & GEARS

SEPARATION PLATE &NEEDLE BEARINGS ASSEMBLY

HEAD & NEEDLE BEARINGS ASSEMBLY

ASSEMBLYCAPSCREWS

ASSEMBLYCAPSCREWS

MATERIALS OF CONSTRUCTION - ALL SERIES

① Needle bearings standard with lip seals.② Carbon graphite Journal bearings standard with mechanical seals.③ Tungsten-carbide coated shafts required with silicon carbide Journal bearings.

Component Standard - SG-04, -05, -07 Standard - SGN -05, -07 Options

Bracket Cast Iron, ASTM A823 Ductile Iron, ASTM A536 Surface Hardening (Vitek)

Casing Cast Iron, ASTM A823 Ductile Iron, ASTM A536 Surface Hardening (Vitek)

Head, Separation Plate Cast Iron, ASTM A823 Ductile Iron, ASTM A536 Surface Hardening (Vitek)

Gears Heat Treated Steel Heat Treated Steel — — —Shafts Heat Treated Steel, ASTM A322 Heat Treated Steel, ASTM A322 — — —Anti-Friction Needle Bearings ① Bearing Steel Bearing Steel — — —

Journal Bearings — — — — — —Carbon Graphite ②,

High Temp Carbon Graphite, Silicon Carbide ③

Outboard Ball Bearing — — — — — — Bearing SteelO-Rings Buna-N Buna-N Neo., Viton®, PTFE, Kalrez®

Lip Seals Buna-N Buna-N Neo., Viton®, PTFE

Component Mechanical Seals Carbon/Ni-Resist Carbon/Ni-Resist Carbon / Silicon Carbide, Silicon Carbide/Silicon Carbide

“B” Drive Foot Bracket Cast Iron, ASTM A48 Cast Iron, ASTM A48 — — —“M” Drive Motor Bracket Cast Iron, ASTM A48 Cast Iron, ASTM A48 — — —





SPECIFICATIONS

Pump Model①

Port Size

(NPT)

Nominal Capacity at Maximum Rated Speed 20 cSt (100 SSU) Liquid

Motor Horsepower / Kilowatts Required at 20 cSt (100 SSU)

Approximate Shipping Weight60 Hz

Motor Speed50 Hz

Motor Speed60 Hz

Motor Speed50 Hz

Motor Speed60 Hz

Motor Speed50 Hz

Motor SpeedBracket Section Head Section 100 PSI 500 PSI 7 BAR 34 BAR

Lip Seal ⑥ Inch GPM RPM M³/Hr RPM GPM RPM M³/Hr RPM HP HP kW kW Lb. Kg.SG-041717 ½ 0.06 1750 0.01 1450 0.06 1750 0.01 1450 ¼ ½ 0.16 0.31 8.3 3.8SG-041718 ½ 0.06 1750 0.01 1450 0.13 1750 0.02 1450 ¼ ½ 0.16 0.31 8.3 3.8SG-041725 ½ 0.06 1750 0.01 1450 0.18 1750 0.03 1450 ¼ ½ 0.16 0.31 8.5 3.9SG-041735 ½ 0.06 1750 0.01 1450 0.25 1750 0.05 1450 ⅓ ¾ 0.21 0.47 8.8 4.0SG-041750 ½ 0.06 1750 0.01 1450 0.36 1750 0.07 1450 ⅓ ¾ 0.21 0.47 9.0 4.1SG-041770 ½ 0.06 1750 0.01 1450 0.50 1750 0.09 1450 ½ ¾ 0.31 0.47 9.3 4.2SG-041818 ½ 0.13 1750 0.02 1450 0.13 1750 0.02 1450 ¼ ½ 0.16 0.31 8.3 3.8SG-041825 ½ 0.13 1750 0.02 1450 0.18 1750 0.03 1450 ⅓ ¾ 0.21 0.47 8.5 3.9SG-041835 ½ 0.13 1750 0.02 1450 0.25 1750 0.05 1450 ⅓ ¾ 0.21 0.47 8.8 4.0SG-041850 ½ 0.13 1750 0.02 1450 0.36 1750 0.07 1450 ⅓ ¾ 0.21 0.47 9.0 4.1SG-041870 ½ 0.13 1750 0.02 1450 0.50 1750 0.09 1450 ½ ¾ 0.31 0.47 9.3 4.2SG-042525 ½ 0.18 1750 0.03 1450 0.18 1750 0.03 1450 ⅓ ¾ 0.21 0.47 8.8 4.0SG-042535 ½ 0.18 1750 0.03 1450 0.25 1750 0.05 1450 ⅓ ¾ 0.21 0.47 9.0 4.1SG-042550 ½ 0.18 1750 0.03 1450 0.36 1750 0.07 1450 ½ ¾ 0.31 0.47 9.3 4.2SG-042570 ½ 0.18 1750 0.03 1450 0.50 1750 0.09 1450 ½ ¾ 0.31 0.47 9.5 4.3SG-043535 ½ 0.25 1750 0.05 1450 0.25 1750 0.05 1450 ½ ¾ 0.31 0.47 9.3 4.2SG-043550 ½ 0.25 1750 0.05 1450 0.36 1750 0.07 1450 ½ 1 0.31 0.62 9.5 4.3SG-043570 ½ 0.25 1750 0.05 1450 0.50 1750 0.09 1450 ½ 1 0.31 0.62 10.0 4.5SG-045050 ½ 0.36 1750 0.07 1450 0.36 1750 0.07 1450 ½ 1 0.31 0.62 10.0 4.5SG-045070 ½ 0.36 1750 0.07 1450 0.50 1750 0.09 1450 ½ 1 0.31 0.62 10.3 4.7SG-047070 ½ 0.50 1750 0.09 1450 0.50 1750 0.09 1450 ½ 1 0.31 0.62 10.5 4.8

Pump Model①

Port Size

(NPT)


Motor Horsepower / Kilowatts Required at 20 cSt (100 SSU) Approximate

Shipping Weight

60 Hz Motor Speed

50 Hz Motor Speed

60 Hz Motor Speed

50 Hz Motor Speed

60 Hz Motor Speed

50 Hz Motor Speed

Bracket Section Head Section 100 PSI 500 PSI 7 BAR 34 BARLip Seal ⑥ Inch GPM RPM M³/Hr RPM GPM RPM M³/Hr RPM HP HP kW kW Lb. Kg.

SG-051818 SGN-051818 ½ 0.7 1750 0.13 1450 0.7 1750 0.13 1450 ¼ ¾ 0.16 0.47 8.3 3.8SG-051825 SGN-051825 ½ 0.7 1750 0.13 1450 1.0 1750 0.19 1450 ¼ ¾ 0.16 0.47 8.5 3.9SG-051835 SGN-051835 ½ 0.7 1750 0.13 1450 1.4 1750 0.26 1450 ¼ 1 0.16 0.62 8.8 4.0SG-051850 SGN-051850 ½ 0.7 1750 0.13 1450 2.0 1750 0.38 1450 ⅓ 1 0.21 0.62 9.0 4.1SG-051870 SGN-051870 ½ 0.7 1750 0.13 1450 2.8 1750 0.53 1450 ½ 1½ 0.31 0.93 9.3 4.2

② SG-051810 ② SGN-051810 ½ 0.7 1750 0.13 1450 4.0 1750 0.91 1450 ½ 2 0.31 1.24 10.0 4.5③ SG-051814 ③ SGN-051814 ½ 0.7 1750 0.13 1450 5.6 1750 1.05 1450 ¾ 3 0.47 1.86 11.0 5.0

SG-052525 SGN-052525 ½ 1.0 1750 0.19 1450 1.0 1750 0.19 1450 ¼ 1 0.16 0.62 8.8 4.0SG-052535 SGN-052535 ½ 1.0 1750 0.19 1450 1.4 1750 0.26 1450 ⅓ 1 0.21 0.62 9.0 4.1SG-052550 SGN-052550 ½ 1.0 1750 0.19 1450 2.0 1750 0.38 1450 ⅓ 1½ 0.21 0.93 9.3 4.2

⑥ Maximum Recommended Temperature with Standard Construction: 225°F (107°C) / ⑤ Maximum Pressure: 500 PSI (34 BAR)

① See model numbering code, page 341.2.2.② When handling liquids with viscosities above 750 SSU (162 cSt), ½” NPT ports

in the casing must be specified for the 10 section.③ When handling liquids with viscosities above 750 SSU (162 cSt), ¾” NPT ports

in the casing must be specified for the 14 section.

⑤ For maximum recommended discharge pressures when handling other viscosities and/or operating at other speeds, see performance curves at www.vikingpump.com/pumpselector.

⑥ Buna-N seals (O-Rings, shaft lip seals) standard, can be used from -40°F. to +225°F. (-40°C. to +107°C.) With sealing elements of other materials, temperatures up to +450°F. (+230°C.) can be tolerated.





SPECIFICATIONS⑥ Maximum Recommended Temperature with Standard Construction: 225°F (107°C) / ⑤ Maximum Pressure: 500 PSI (34 BAR)

Pump Model①

Port Size

(NPT)


Motor Horsepower / Kilowatts Required at 20 cSt (100 SSU) Approximate

Shipping Weight

60 Hz Motor Speed

50 Hz Motor Speed

60 Hz Motor Speed

50 Hz Motor Speed

60 Hz Motor Speed

50 Hz Motor Speed

Brkt. Sect. Head Sect. 100 PSI 500 PSI 7 BAR 34 BARLip Seal ⑥ Inch GPM RPM M³/Hr RPM GPM RPM M³/Hr RPM HP HP kW kW Lb. Kg.

SG-052570 SGN-052570 ½ 1.0 1750 0.19 1450 2.8 1750 0.53 1450 ½ 1½ 0.31 0.93 9.5 4.3② SG-052510 ② SGN-052510 ½ 1.0 1750 0.19 1450 4.0 1750 0.75 1450 ½ 2 0.31 1.24 10.3 4.7③ SG-052514 ③ SGN-052514 ½ 1.0 1750 0.19 1450 5.6 1750 1.05 1450 ¾ 3 0.47 1.86 11.8 5.3

SG-053535 SGN-053535 ½ 1.4 1750 0.26 1450 1.4 1750 0.26 1450 ⅓ 1½ 0.21 0.93 9.3 4.2SG-053550 SGN-053550 ½ 1.4 1750 0.26 1450 2.0 1750 0.38 1450 ½ 1½ 0.31 0.93 9.5 4.3SG-053570 SGN-053570 ½ 1.4 1750 0.26 1450 2.8 1750 0.53 1450 ½ 1½ 0.31 0.93 10.0 4.5

② SG-053510 ② SGN-053510 ½ 1.4 1750 0.26 1450 4.0 1750 0.75 1450 ¾ 2 0.47 1.24 10.5 4.8③ SG-053514 ③ SGN-053514 ½ 1.4 1750 0.26 1450 5.6 1750 1.05 1450 ¾ 3 0.47 1.86 11.5 5.2

SG-055050 SGN-055050 ½ 2.0 1750 0.38 1450 2.0 1750 0.38 1450 ½ 1½ 0.31 0.93 10.0 4.5SG-055070 SGN-055070 ½ 2.0 1750 0.38 1450 2.8 1750 0.53 1450 ½ 2 0.31 1.24 10.3 4.7

② SG-055010 ② SGN-055010 ½ 2.0 1750 0.38 1450 4.0 1750 0.75 1450 ¾ 3 0.47 1.86 10.8 4.9③ SG-055014 ③ SGN-055014 ½ 2.0 1750 0.38 1450 5.6 1750 1.05 1450 ¾ 3 0.47 1.86 11.8 5.3

SG-057070 SGN-057070 ½ 2.8 1750 0.53 1450 2.8 1750 0.53 1450 ¾ 2 0.47 1.24 100 4.5② SG-057010 ② SGN-057010 ½ 2.8 1750 0.53 1450 4.0 1750 0.75 1450 ¾ 3 0.47 1.86 11.0 5.0③ SG-057014 ③ SGN-057014 ½ 2.8 1750 0.53 1450 5.6 1750 1.05 1450 1 3 0.62 1.86 12.0 5.5② SG-051010 ② SGN-051010 ½ 4.0 1750 0.75 1450 4.0 1750 0.75 1450 ¾ 3 0.47 1.86 11.5 5.2

②③ SG-051014 ②③ SGN-051014 ½ 4.0 1750 0.75 1450 5.6 1750 1.05 1450 1 5 0.62 3.11 12.8 5.8③ SG-051414 ③ SGN-051414 ½ 5.6 1750 1.05 1450 5.6 1750 1.05 1450 1 5 0.62 3.11 13.8 6.2

SG-072929 SGN-072929 1 2.8 1750 0.53 1450 2.8 1750 0.53 1450 1 3 0.62 1.86 30.8 14.0SG-072941 SGN-072941 1 2.8 1750 0.53 1450 4.0 1750 0.75 1450 1 3 0.62 1.86 32.0 14.5SG-072958 SGN-072958 1 2.8 1750 0.53 1450 5.6 1750 1.05 1450 1½ 5 0.93 3.11 33.5 15.2SG-072982 SGN-072982 1 2.8 1750 0.53 1450 8.0 1750 1.50 1450 1½ 5 0.93 3.11 34.5 15.7

④ SG-072911 ④ SGN-072911 1 2.8 1750 0.53 1450 11.2 1750 2.10 1450 1½ 5 0.93 3.11 35.8 16.2④ SG-072916 ④ SGN-072916 1 2.8 1750 0.53 1450 16.0 1750 3.00 1450 2 7½ 1.24 4.66 370 16.8

SG-074141 SGN-074141 1 4.0 1750 0.75 1450 4.0 1750 0.75 1450 1 3 0.62 1.86 33.0 15.0SG-074158 SGN-074158 1 4.0 1750 0.75 1450 5.6 1750 1.05 1450 1½ 5 0.93 3.11 34.5 15.7SG-074182 SGN-074182 1 4.0 1750 0.75 1450 8.0 1750 1.50 1450 1½ 5 0.93 3.11 35.8 16.2

④ SG-074111 ④ SGN-074111 1 4.0 1750 0.75 1450 11.2 1750 2.10 1450 1½ 7½ 0.93 4.66 37.0 16.8④ SG-074116 ④ SGN-074116 1 4.0 1750 0.75 1450 16.0 1750 3.00 1450 2 7½ 1.24 4.66 38.0 17.5

SG-075858 SGN-075858 1 5.6 1750 1.05 1450 5.6 1750 1.05 1450 1½ 5 0.93 3.11 36.5 16.6SG-075882 SGN-075882 1 5.6 1750 1.05 1450 8.0 1750 1.50 1450 2 5 1.24 3.11 37.5 17.0

④ SG-075811 ④ SGN-075811 1 5.6 1750 1.05 1450 11.2 1750 2.10 1450 2 7½ 1.24 4.66 38.5 17.5④ SG-075816 ④ SGN-075816 1 5.6 1750 1.05 1450 16.0 1750 3.00 1450 2 7½ 1.24 4.66 39.5 17.9

SG-078282 SGN-078282 1 8.0 1750 1.50 1450 8.0 1750 1.50 1450 2 7½ 1.24 4.66 38.5 17.5④ SG-078211 ④ SGN-078211 1 8.0 1750 1.50 1450 11.2 1750 2.10 1450 2 7½ 1.24 4.66 39.5 17.9④ SG-078216 ④ SGN-078216 1 8.0 1750 1.50 1450 16.0 1750 3.00 1450 3 10 1.86 6.21 40.8 18.5④ SG-071111 ④ SGN-071111 1 11.2 1750 2.10 1450 11.2 1750 2.10 1450 2 10 1.24 6.21 40.8 18.5④ SG-071116 ④ SGN-071116 1 11.2 1750 2.10 1450 16.0 1750 3.00 1450 3 10 1.86 6.21 41.8 19.0④ SG-071616 ④ SGN-071616 1 16.0 1750 3.00 1450 16.0 1750 3.00 1450 3 15 1.86 9.32 43.0 19.5

① See model numbering code, page 341.2.2.② When handling liquids with viscosities above 750 SSU (162 cSt), ½” NPT ports in

the casing must be specified for the 10 section.③ When handling liquids with viscosities above 750 SSU (162 cSt), ¾” NPT ports in

the casing must be specified for the 14 section.④ When handling liquids with viscosities above 750 SSU (162 cSt) with “11” or “16”

section pumps, consult factory for port recommendations.

⑤ For maximum recommended discharge pressures when handling other viscosities and/or operating at other speeds, see performance curves at www.vikingpump.com/pumpselector.

⑥ Buna-N seals (O-Rings, shaft lip seals) standard, can be used from -40°F. to +225°F. (-40°C. to +107°C.) With sealing elements of other materials, temperatures up to +450°F. (+230°C.) can be tolerated.





DRIVE OPTIONS

FOOT-BRACKET MOUNTED PUMPS (“B” DRIVE)Series SG-04, SG-05 and SG-07 external gear double pumps are available mounted to a foot-bracket that is machined by Viking for an accurate fit with the pump.Dimensions for Foot-Bracket Mounted Pumps (“B” Drive)— See Page 341.2.12.

BASE MOUNTED UNITS (“D” DRIVE)Series SG-04, SG-05 and SG-07 external gear double pumps mounted to a Viking rectangular, formed steel base provides you with a solid mounting for the drive equipment and the foot-bracket mounted pump.NOTE: This mounting arrangement requires on-site cou pling alignment.Dimensions for Base-Mounted Units (“D” Drive)— See Page 341.2.13.

MOTOR MOUNTED UNITS (“M” DRIVE)Series SG-04, SG-05 and SG-07 external gear double pumps, in combination with a NEMA “C” flange or IEC bracket and flexible coupling, provide an easily assembled compact pumping unit. This mounting arrangement eliminates the need for on-site coupling alignment that is normally required with a base-mounted unit.

Dimensions for NEMA C-Flange Motor Mounted Units (“M” Drive)— See Page 341.2.10.

Dimensions for IEC-Flange Motor Mounted Units (“M” Drive)— See Page 341.2.11.





DIMENSIONS – SERIES SG-04, SG-05, SGN-05 UNMOUNTED DOUBLE PUMPS

MODEL NO. B C MODEL NO. B C

SG-041717 SG-041818 SG-051818in 3.17 3.86

SG-043550 SG-053550in 3.66 4.35

mm 81 98 mm 93 110

SG-041718in 3.17 3.86

SG-043570 SG-053570in 3.86 4.55

mm 81 98 mm 98 116

SG-041725 SG-041825 SG-051825in 3.24 3.93

SG-053510in 4.16 4.85

mm 82 100 mm 106 123

SG-041735 SG-041835 SG-051835in 3.34 4.03

SG-053514in 4.56 5.25

mm 85 102 mm 116 133

SG-041750 SG-041850 SG-051850in 3.49 4.18

SG-045050 SG-055050in 3.81 4.50

mm 89 106 mm 97 114

SG-041770 SG-041870 SG-051870in 3.69 4.38

SG-045070 SG-055070in 4.01 4.70

mm 94 111 mm 102 119

SG-051810in 3.99 4.68

SG-055010in 4.31 5.00

mm 101 119 mm 109 127

SG-051814in 3.39 5.08

SG-055014in 4.71 5.40

mm 86 129 mm 120 137

SG-042525 SG-052525in 3.31 4.00

SG-047070 SG-057070in 4.21 4.90

mm 84 102 mm 107 124

SG-042535 SG-052535in 3.41 4.10

SG-057010in 4.51 5.20

mm 87 104 mm 115 132

SG-042550 SG-052550in 3.56 4.25

SG-057014in 4.91 5.60

mm 90 108 mm 125 142

SG-042570 SG-052570in 3.76 4.45

SG-051010in 4.81 5.50

mm 96 113 mm 122 140

SG-052510in 4.06 4.75

SG-051014in 5.21 5.90

mm 103 121 mm 132 150

SG-052514in 4.46 5.15

SG-051414in 5.61 6.30

mm 113 131 mm 142 160

SG-043535 SG-053535in 3.51 4.20

mm 89 107

NOTE: Dimensions in inches (millimeters)





DIMENSIONS – SERIES SG-07, SGN-07 UNMOUNTED DOUBLE PUMPS

NOTE: Dimensions in inches (millimeters)

MODEL NO. B₁ B₂ C MODEL NO. B₁ B₂ C

SG-072929in 3.42 5.96 7.08 SG-075858

SGN-075858in 3.71 6.54 7.66

mm 87 151 180 mm 94 166 195

SG-072941in 3.42 6.08 7.20 SG-075882

SGN-075882in 3.71 6.78 7.90

mm 87 154 183 mm 94 172 201

SG-072958in 3.42 6.25 7.37 SG-075811

SGN-075811in 3.71 7.11 8.23

mm 87 159 187 mm 94 181 209

SG-072982in 3.42 6.49 7.61 SG-075816

SGN-075816in 3.71 7.61 8.73

mm 87 165 193 mm 94 193 222

SG-072911in 3.42 6.82 7.94 SG-078282

SGN-078282in 3.95 7.02 8.14

mm 87 173 202 mm 100 178 207

SG-072916in 3.42 7.32 8.44 SG-078211

SGN-078211in 3.95 7.35 8.47

mm 87 186 214 mm 100 187 215

SG-074141SGN-074141

in 3.54 6.20 7.32 SG-078216SGN-078216

in 3.95 7.85 8.97

mm 90 157 186 mm 100 199 228

SG-074158SGN-074158

in 3.54 6.37 7.49 SG-071111SGN-071111

in 4.28 7.68 8.80

mm 90 162 190 mm 109 195 224

SG-074182SGN-074182

in 3.54 6.61 7.73 SG-071116SGN-071116

in 4.28 8.18 9.30

mm 90 168 196 mm 109 208 236

SG-074111SGN-074111

in 3.54 6.94 8.06 SG-071616SGN-071616

in 4.78 8.68 9.80

mm 90 176 205 mm 121 220 249

SG-074116SGN-074116

in 3.54 7.44 8.56

mm 90 189 217





MOTOR FRAME SIZE D E F H MC MD APPROX. DRIVE ① EQUIP. SHIPPING WEIGHT IN POUNDS (KG)

56C in (mm) 3.50 (88.9) 2.44 (62.0) 1.50 (38.1) .34 (8.6) SLOT 2.56 (65.0) 3.75 (95.3) 34 (15)143TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.00 (50.8) .34 (8.6) 2.88 (73.2) 3.75 (95.3) 52 (24)145TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.50 (63.5) .34 (8.6) 2.88 (73.2) 3.75 (95.3) 57 (26)182TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.25 (57.15) .41 (10.4) 3.62 (92.0) 4.25 (108.0) 83 (38)184TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.75 (69.9) .41 (10.4) 3.62 (92.0) 4.25 (108.0) 88 (40)

MOTOR FRAME SIZE D E F H MC MDAPPROX. DRIVE ① EQUIP. SHIPPING

WEIGHT IN POUNDS (KG)

56C in (mm) 3.50 (88.9) 2.44 (62.0) 1.50 (38.1) .34 (8.6) SLOT 2.56 (65.0) 4.88 (124.0) 41 (19)143TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.00 (50.8) .34 (8.6) 2.88 (73.2) 4.88 (124.0) 60 (27)145TC in (mm) 3.50 (88.9) 2.75 (69.9) 2.50 (63.5) .34 (8.6) 2.88 (73.2) 4.88 (124.0) 70 (32)182TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.25 (57.15) .41 (10.4) 3.62 (92.0) 5.59 (142.0) 108 (49)184TC in (mm) 4.50 (114.3) 3.75 (95.3) 2.75 (69.9) .41 (10.4) 3.62 (92.0) 5.59 (142.0) 123 (56)213TC in (mm) 5.25 (133.4) 4.25 (108.0) 2.75 (69.9) .41 (10.4) 4.50 (114.3) 6.26 (159.0) 161 (73)215TC in (mm) 5.25 (133.4) 4.25 (108.0) 3.50 (88.9) .41 (10.4) 4.50 (114.3) 6.26 (159.0) 195 (88)

DIMENSIONS – SERIES SG-04, SG-05, SGN-05 C-FLANGE MOTOR MOUNT (“M” DRIVE) – NEMA

DIMENSIONS – SERIES SG-07, SGN-07 – C-FLANGE MOTOR MOUNT (“M” DRIVE) – NEMA

① Drive equipment weight listed is for a typical TEFC motor, mounting bracket and couplings. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the drive equipment shipping weight to the pump shipping weight shown on the pump specification chart.

① Drive equipment weight listed is for a typical TEFC motor, mounting bracket and couplings. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the drive equipment shipping weight to the pump shipping weight shown on the pump specification chart.





DIMENSIONS – SERIES SG-04, SG-05, SGN-05 – MOTOR MOUNT – (“M” DRIVE) – IEC FRAME

MOTOR FRAME D E F G H MC MD APPROX. DRIVE ① EQUIP. SHIPPING WEIGHT IN POUNDS (KG)

IEC 80 B35 FLANGE in (mm) 3.15 (80) 2.46 (62.5) 1.97 (50) 3.94 (100) 0.39 (10) 1.97 (50) 3.73 (94.7) 46 (21)

IEC 90 B35 FLANGE in (mm) 3.54 (90) 2.76 (70) S 1.97 (50) /

L 2.46 (62.5) 3.94 (100) 0.39 (10) 2.20 (56) 3.73 (94.7) 64 (29)

MOTOR FRAME D E F G H MC MD APPROX. DRIVE ① EQUIP. SHIPPING WEIGHT IN POUNDS (KG)

IEC 90 B35 FLANGE in (mm) 3.54 (90) 2.76 (70) S 1.97 (50) /

L 2.46 (62.5) 3.94 (100) 0.39 (10) 2.20 (56) 5.13 (130.3) 68 (31)

IEC 100 B14 FACE in (mm) 3.94 (100) 3.15 (80) S 2.20 (56) /

L 2.76 (70) --- 0.47 (12) 2.48 (63) 5.26 (133.6) 114 (52)

IEC 112 B14 FACE in (mm) 4.41 (112) 3.74 (95) S 2.24 (57) /

L 2.76 (70) --- 0.47 (12) 2.76 (70) 5.26 (133.6) 129 (59)

DIMENSIONS – SERIES SG-07, SGN-07 – MOTOR MOUNT (“M” DRIVE) – IEC FRAME

① Motor shipping weight listed is for a typical IEC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the electric motor shipping weight to the pump shipping weight shown on the pump specification chart.

① Motor shipping weight listed is for a typical IEC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.) For total unit shipping weight, add the electric motor shipping weight to the pump shipping weight shown on the pump specification chart.





DIMENSIONS – SERIES SG-04, SG-05, SGN-05 FOOT BRACKET MOUNT (“B” DRIVE)

NOTE: Approximate shipping weight of foot bracket is 2¼ lbs. (0.9 kg)NOTE: Dimensions in inches (millimeters). NOTE: Bracket part number is 2-070-012-100-00NOTE: Shaft height corresponds to Viking’s “A” reducer or NEMA 56, 143T and 145T motors.

DIMENSIONS – SERIES SG-07, SGN-07 – FOOT BRACKET MOUNT (“B” DRIVE)

NOTE: Approximate shipping weight of foot bracket is 5 lbs. (1.9 kg)NOTE: Dimensions in inches (millimeters). NOTE: Bracket part number is 2-070-200-100-00.NOTE: Shaft height corresponds to NEMA 182T and 184T motors.





DIMENSIONS – SERIES SG-04, SG-05, SGN-05 BASE-MOUNTED UNIT (“D” DRIVE)

DIMENSIONS – SERIES SG-07, SGN-07 BASE-MOUNTED UNIT (“D” DRIVE)

MOTOR FRAME SIZE D E F G H J K APPROX. MOTOR ① SHIPPING WEIGHT IN POUNDS (KG)

APPROX. DRIVE ② EQUIP. SHIPPING WEIGHT IN POUNDS (KG)

56in 4.50 8.50 20.50 1.50 .50 .75 .75

31 (14)38 (17)143T 50 (23)

(mm) (114) (216) (520) (190) (13) (19) (19)145T 60 (27)182T in 4.50 9.00 25.00 2.94 .56 1.50 1.00 95 (43)

49 (22)184T (mm) (114) (229) (635) (75) (14) (38) (25) 110 (50)213T in 5.25 9.00 25.00 2.94 .56 1.50 1.00 145 (66)

56 (25)215T (mm) (133) (229) (635) (75) (14) (38) (25) 179 (81)

MOTOR FRAME SIZE D APPROX. MOTOR ① SHIPPING WEIGHT IN POUNDS (KG)

APPROX. DRIVE ② EQUIP. SHIPPING WEIGHT IN POUNDS (KG)

56in 3.50

31 (14) 17 (8)mm 89

143Tin 3.50

50 (23) 17 (8)mm 89

145Tin 3.50

60 (27) 17 (8)mm 89

182Tin 4.50

95 (43) 20 (9)mm 114

184Tin 4.50

110 (50) 20 (9)mm 114

① Motor shipping weight listed is for a typical TEFC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.)

② Drive equipment shipping weight includes base, foot-bracket, coupling and coupling guard. For total unit shipping weight, add electric motor shipping weight, drive equipment shipping weight and the pump shipping weight shown on the pump specification chart.

① Motor shipping weight listed is for a typical TEFC motor. (If a more accurate motor shipping weight is required, consult factory with complete motor specifications.)

② Drive equipment shipping weight includes base, foot-bracket, coupling and coupling guard. For total unit shipping weight, add electric motor shipping weight, drive equipment shipping weight and the pump shipping weight shown on the pump specification chart.

NOTE: Dimensions in inches (millimeters).

NOTE: Dimensions in inches (millimeters).





Printed performance curves are not available.

Performance curves for individual pump sections can be electronically generated with the Viking Pump Selector Program. This program can be located on www.vikingpump.com/pumpselector for the general public.

For authorized distributors, this program can be found listed under the “Products” tab at www.idexconnect.com. Security passwords are required to access IDEXconnect.

PERFORMANCE CURVE NOTES

viking sg series double pumps (with shaft seal)vp.salesmrc.com/pdfs/sec_341.2.pdf · viking pump a...

Documents