vinod_verma_resume_mtech_28_01_2016
TRANSCRIPT
VINOD INDRADEV VERMA B-2 , G.V.S REPAIRING WORKS , Durganagar-A , Bhimnagar Road, Boisar , Palghar , Maharashtra , Pin No.401506.
[email protected], Cell No.9890899510/7769988742
CAREER OBJECTIVE
I want to work with a progressive organization that provides an opportunity to learn, enhance and apply my
Knowledge and skills.
EDUCATION
Symbiosis International University (Symbiosis Institute of Technology)
Master of Technology in CAD/CAM(Pursuing) 2015-2017
Semister-1 : 9.41(GPA)
University of Pune (AVCOE, Sangamner)
B.E in Mechanical Engineering 2010-2014
Aggregate : 71.87%
Maharashtra State Board
HSC (M.K. Junior College) : 84.83% 2009-2010
SSC (Adarsh Vidyalaya) : 87.53% 2007-2008
TECHNICAL SKILLS
CAD Software : CATIA , PRO-E , AUTO-CAD , SolidWorks , U.G
CAM Software : MASTER-CAM(X5)
CAE Software : ANSYS,HYPERMESH
FLUID software : FluidSim-H,FluidSim-P
Languages : Basics of C
WORK EXPERIENCE
GAE at Ring Plus Aqua Ltd. (A Subsidiary of Raymond Ltd.) July2014 -July2015
Worked under Manufacturing Engineering and Projects Department:
o New Product development activities like Feasibility study, Modeling & Design of Product,
APQP, PPAP Documents, Production, QA and Dispatch.
o Process & Productivity improvement Projects like Streamlining the Flow, SMED approach,
Fixture design & Automation.
o Die Design and Development for New products.
o Flash-less die design & Yield improvement of Products.
o Tooling Cost reduction by Die life improvement Project.
o OEE improvement of Forge Shop by Tracing and reducing the Downtime losses.
Attended Internal Training on 7QC tools & SPC.
PROJECT AS A TRAINEE
Layout Improvement for Optimization of machine shop.
o Process flow study, Cycle time study, Identification & Elimination of NVA Activities, Buffer
Stock Defining and SOP re-modification and based on all these Proposed a Feasible Solution
for Layout to achieve Optimum manufacturing time.
Ensure effective utilization of available resources and feasibility study of Cell formation at Hob
Tooth Chamfer section.
o Ensure effective utilization of resources like man, machine, material etc. and study the cell
formation feasibility by doing man-machine and time study.
Fixture Design & Automation for Arresting Tooth Chamfer Missing on Ring gears.
o New fixture design to arrest tooth chamfer missing and proposal for an automated system
which uses proximity sensor for detection of chamfer missing.
ACADEMIC PROJECT
B.E Project : “Dynamic Balancing of the vehicle while cornering”
“Dynamic Balancing of the vehicle while cornering” is the concept to avoid Roll-Over of the
vehicle and provide comfort to the passengers while cornering by tilting the vehicle opposite to the
centrifugal force to cancel it, which leads to shift of C.G point of vehicle and provide comfort to the
passengers.
ADVANCED COURSES
CATIA V5R19 at VENUS TECHNOLOGY, PUNE.
ANSYS 12.0 at i-Global, PUNE.
Workshop on “Hydraulic & pneumatics” by TAACT.
Aptitude & Soft Skill at SEED InfoTech.
EXTRA-CURRICULAR ACTIVITIES
Volunteered at “GLOGIFT-2015-International Conference” at Symbiosis Institute Of
Technology.
Vice-Captain, Designer & Electrician in “BAJA SAE-INDIA”
Organizer of “ROBORACE in KURUKSHETRA-A National Level Event”
Coordinator of “ROBORACE in TECHUNIQUE2K13-A National Level Event”
National level Paper Presentation: 1. TMDS at K.K.WAGH COLLEGE, Nasik.
2. TMDS at MIT, Pune.
3. TMDS in INTERNATIONAL CONFERENCE at AVCOE, Sangamner.
Attended a “Bike Workshop” at Sinhagad, Vadgaon.
AREA OF INTEREST
CAD & CAE (Analysis & Simulation) Tools
R & D Activities
New Product Development Activities
LANGUAGES
Fluent in Hindi, English, Marathi
HOBBIES
Playing Cricket, Reading Books
Vinod I. Verma