wft217711
TRANSCRIPT
![Page 1: WFT217711](https://reader037.vdocuments.net/reader037/viewer/2022100312/577cc58d1a28aba7119cc2bf/html5/thumbnails/1.jpg)
8/11/2019 WFT217711
http://slidepdf.com/reader/full/wft217711 1/2
weatherford.com 1
Wireline Services
© 2012–2014 Weatherford. All rights reserved. 10139.01
Production LoggingCased Hole
Spinner Array Tool
The Weatherford Spinner Array Tool (SAT) has six miniature impellers
deployed on bow-spring arms, enabling discrete local uid velocities to be
measured at 60-degree intervals around the wellbore. The SAT provides
direct measurement of individual phase velocities. Combining SAT data
with holdup data from the Resistance Array Tool (RAT) and the Capacitance
Array Tool (CAT) provides quantitative estimates of the volumetric ow rate
of each phase with a much higher degree of certainty and thus provides
vital information for reservoir management.
The SAT outputs the direction and speed of spinner rotation, and a relative
bearing measurement is incorporated to indicate the high side of the well.
MAPview software uses data from the SAT to present three-dimensional
imaging of the velocity prole.
• Fluid-velocity measurements in deviated or horizontal wellbores as
part of a production prole
Applications
• Cross-sectional velocity proling provides phase velocities in segregated
uid streams for deviated and horizontal wells.
• The SAT can be deployed by multiple conveyance methods, and SAT
data is available at the surface and from memory. This exibility enables
using the most cost-effective deployment method.
• The SAT enables simultaneous operation with Sondex™ and Ultrawire™
tools that measure other aspects of the ow stream, such as uid makeup
at the same time as the uid velocity. This ensures that all measurements
are obtained at the same time for a more accurate ow prole.
• The turbines use low-friction jeweled bearings to reduce the mechanical
threshold of the spinner and improve sensitivity to uid ow.
Features, Advantages, and Benefts
Sondex and Ultrawire are trademarks of the General Electric Company.
![Page 2: WFT217711](https://reader037.vdocuments.net/reader037/viewer/2022100312/577cc58d1a28aba7119cc2bf/html5/thumbnails/2.jpg)
8/11/2019 WFT217711
http://slidepdf.com/reader/full/wft217711 2/2
weatherford.com 2
Wireline Services
Specifcations
Measurement specifcations
Model SAT004 SAT005
Pipe range Up to 7 in. (177.8 mm) casing
Sensor measurement point 16.5 in. (419 mm)
Relative bearing accuracy 5º
Relative bearing deviation range 5º to 175º
Number of sensors 6
Mechanical specifcations
Outer diameter 1.72 in. (43.69 mm) 2.125 in. (53.98 mm)
Spinner diameter 0.4 in. (10.16 mm) 0.6 in. (15.24 mm)
Length 45.5 in. (1,156 mm)
Total weight (in air) 17.2 lb (7.8 kg)
Maximum pressure 15,000 psi (103.4 MPa)
Maximum temperature 350°F (177°C)
Current consumption 25 mA
Materials Corrosion-resistant
Toolbus Ultrawire
© 2012–2014 Weatherford. All rights reserved. 10139.01
Production LoggingCased Hole
Spinner Array Tool
Weatherford products and services are subject to the Company’s standard terms and conditions, available on request or at weatherford.com. For more information contact an authorized Weatherford representative.
Unless noted otherwise, trademarks and service marks herein are the property of Weatherford and may be registered in the United States and/or other countries. Weatherford products named herein may be
protected by one or more U.S. and/or foreign patents. Specications are subject to change without notice. Weatherford sells its products and services in accordance with the terms and conditions set forth in the
applicable contract between Weatherford and the client.
Tool drawings and specications provided by GE Oil & Gas.
Specifcations