wincor nixdorf configprogmanual_english

8/8/2019 Wincor Nixdorf ConfigProgManual_english

http://slidepdf.com/reader/full/wincor-nixdorf-configprogmanualenglish 1/7

PRN_LOAD 17.04.2002 16:22

PRN_LOAD.EXE is a user-friendly program for loading the HPR4915 with newfirmware or fonts. It is based on the DOS operating system and also runs under WIN 95/89/NTWIN2000 WIN ME WIN XP and OS/2. However, under these operating systems, it requires a free COM port for connecting to the printer by means of a serial cable. In order to update the firmware, the file 4915XXXX.STD must be available.In order to update the fonts, the file CPXXXXXX.FNT must be available. Download these files from the Internet site www.wincor-nixdorf.com to your hard diskor onto a system disk together with the program PRN_LOAD.EXE. Then start the PRN_LOAD program.

The screen shown above appears.

http://www.wincor-nixdorf.com/



PRN_LOAD 17.04.2002 16:22

Now switch on the printer with the Eject key held down. (if the printer is alreadyswitched on, you must first switch it off). Now press a key to start the loadingprocedure. Pressing the “E” key takes you to expert mode.

This screen output shows the progress of the loading process.

This screen output appears after the printer has been updated successfully.The printer is automatically reset and is then ready to operate.



PRN_LOAD 17.04.2002 16:22

EXPERT MODE The following functions can be selected in this mode.

However, you can only select one function from this menu. 1. Load firmware and/or font

2. Unload the printer parameters in order to save them in a file3. Configure a printer with the data from a file. Use the cursor keys to get from one menu item to another. Mark the requiredmenu item with the spacebar.The CR key starts the selected function.



PRN_LOAD 17.04.2002 16:22

The required loading functions(s) can be chosen in this menu.Mark the required function(s) with the space bar; use the TAB key to skip fromone item to the next. When you have selected the required items (you can select several at once),

use the OK switch to reach the next menu item.

You can select the required file(s) here. If you selected several items in theprevious menu, then this menu appears again and prompts you until all fileshave been marked. Only then is the loading process started. Loading a second font requires a printer version with extended memory. A TBFfont can be loaded here. The loading process is then shown as described above. Wait until all files havebeen transferred and the printer has reset itself.



PRN_LOAD 17.04.2002 16:22

READ PARAMETER

To save the print parameters in a file, select Read Parameter.

This screen output shows the progress of file transfer.



PRN_LOAD 17.04.2002 16:22

The following menu enables you to assign a specific name for the relevantproject. This name can then be used to load additional printers with the sameparameters.

Simply overwrite the name 4915auto.ini with the keypad. Enter at least 8characters; the Anhang .INI file is generated automatically. Please do not use the name 4915AUTO.INI; this is reserved for the fullyautomatic loading and configuration of the printer (described below) To load another printer with the same parameters, connect this printer to your system and start the program again. Now select the Write Parameter item as described above . Now select the parameter file.

Wait until the printer has finished resetting. this enables customer-specificprinter settings to be made quickly and easily.



PRN_LOAD 17.04.2002 16:22

Selection menu for the parameter file Fully automatic printer initialization

Fully automatic printer initialization is a way to load the printer with therequired firmware level, the required font and the entire printer configuration inthe simplest possible manner. Proceed as follows: First load a printer with the firmware and fonts required as described above.Configure these as required in the system environment. Now read the printer configuration using the program (Read parameters)and save the data in the 4915AUTO.INI file.

Copy the firmware file (*.MOD), the font file (*.FNT) , the 4915AUTO.INI file andthe PRN_LOAD.EXE program onto a bootable diskette.

Edit the “AUTOEXEC.BAT“ file and insert the entry PRN_LOAD at the end of the file. Now start the PC with this diskette, bring the printer into the described mode(EJECT + POWER ON) and start the program by pressing a key. Then wait untilthe program is finished. (Of course you can also copy all files into a directory on the hard disk and start from there)

wincor nixdorf configprogmanual_english

Documents