xerox 700 dcp customer expectations document - rev.3.3

Xerox 700 Digital Color Press Version 3.0 System Software Customer Expectations Document

©2008 Xerox Corporation. All rights reserved. Xerox and the sphere of connectivity design and DocuColor®, DocuTech®, FreeFlow®, iGen3®, ProfitAccelerator®, VIPP® and iGen4™ are trademarks of Xerox Corporation in the United States and/or other countries.

Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs displayed on the screen such as icons, screen displays, or looks.

Other company trademarks are also acknowledged.

Printed in the United States of America.

Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions.

Document Version: 3.3 (1 June 2009)

3

Table of Contents The 700 Digital Color Press .................................................................................................. 4 Centerline Paper........................................................................................................................ 4 Optimum Product Performance ......................................................................................... 4 Product Specifications ............................................................................................................ 5 Product Caveats/Limitations................................................................................................ 8 Media Selection Guidelines .................................................................................................. 9 Media Support Documentation ......................................................................................... 9 Print Engine Productivity Speeds- IPM (Impressions per Minute) .....................10 Image Quality ..........................................................................................................................13 Non-Standard paper sizes...................................................................................................14 Duplex Prints .............................................................................................................................14 Integrated Scanner................................................................................................................14 Paper/Throughput..................................................................................................................15 Transparencies.........................................................................................................................16 Envelopes ...................................................................................................................................16 Recommended Supplies ......................................................................................................17 Initial Supplies..........................................................................................................................18 Environmental and Electrical Requirements ...............................................................18 Space Requirements..............................................................................................................23 Physical Dimensions ..............................................................................................................24 Standard Configuration Features....................................................................................26 Optional Accessories .............................................................................................................26 Combination of Output Functions and Destinations..............................................28 Optional High Capacity Feeder (HCF) ...........................................................................28 Optional Oversized High Capacity Feeder (OHCF)...................................................29 Product Specifications (OHCF)..........................................................................................29 Advanced Finisher ..................................................................................................................30 Professional Finisher..............................................................................................................30 Optional High Capacity Stacker (HCS) ..........................................................................31 Optional Interface Module (IFM)....................................................................................32 Optional Light Production C Finisher (shown with Optional Booklet Maker)32 Light Production C Finisher Product Specifications..................................................33 Light Production C Finisher Product Caveats/Limitations.....................................39 GBC Advanced Punch ...........................................................................................................40 SquareFold® Trimmer Module.........................................................................................42 Combining High Capacity Stacker and the Light Production C Finisher.........44 Supported Configurations ..................................................................................................45 Customer Agreement............................................................................................................48 Customer Expectations Agreement................................................................................50

4

The 700 Digital Color Press

Centerline Paper

All references to media capacity and performance in this document are based on centerline paper. You will see the term “Centerline paper” several times in this document.

Media Type Xerox Equivalent Uncoated paper

North America - Xerox Color Xpressions Plus (90 g/m2/24 lbs) Europe – Colotech+ (90 g/m2/24 lbs)

Xerox 700 Digital Color Press centerline paper

Coated paper

North America – Xerox Digital Color Elite Gloss 80# Text (120 g/m2) Europe – Xerox Digital Color Elite Gloss 80# Text (120 g/m2)


Customers may obtain a copy of the Xerox Recommended Materials List for the Xerox 700 Digital Color Press by going to <http://www.xerox.com/downloads/usa/en/r/RML_700_DCP.pdf>

Optimum Product Performance

Print Volume Range

The Xerox 700 Digital Color Press is designed for an average monthly print volume range (AMPV Range):

Press AMPV Range Conditions

Xerox 700 Digital Color Press 20,000 – 75,000 8.5 in x 11 in/A4

The Xerox 700 Digital Color Press is designed to produce a consistent uniform-looking color image. The Xerox 700 Digital Color Press is designed to operate in the range of 20,000 – 75,000 copies or prints per month. The number of copies or prints between service calls on a digital color copier / printer is highly dependent on customer expectations of quality and the use of applications and throughput materials. At an average usage of 35,000 copies or prints per month using centerline paper, it is expected that service will be required about once every 5 weeks.

5

Product Specifications

The following table contains the specifications for the performance of the Xerox 700 Digital Color Press.

Item Xerox 700 Digital Color Press Comments

Internal tray capacity • 3 trays; 550 sheet capacity each

• Represents capacity using Xerox Color Xpressions Plus or Xerox Colotech+ centerline paper.

Paper Speeds of Media Weight for each paper weight setting (8.5 in x 11 in /A4 LEF ppm)

• Productivity Mode Settings • Refer to Print Engine Productivity Speeds chart

• Does not include finishing

• The machine will pause for xerographic adjustment when necessary. This will impact productivity.

Transparency feeding • 40 ppm b/w, 23 for color • USA and Canada: 3R3028, 3R3108; Xerox Europe: 3R98199, 3R3108. These premium transparencies are specifically designed to provide optimum copy quality.

• Use of other transparencies may cause machine damage and result in excessive service calls.

Paper weight range • 64-300 g/m2 (18 lb bond – 110 lb. cover)

• Papers that are 80 g/m2 or lighter and less than 210mm (8.3 in) may have increased jam rates.

Paper Size • Min: 5.5” x 7.2” (140mm x 182mm)

• Max: 13” x 19.2” (330mm x 488mm)

Imageable Area • Copy: Guaranteed Image Quality area is 297 mm x 432 mm (11.69 in x 17.00 in).

• Print: Guaranteed Image Quality area 317 mm x 480 mm (12.48 in x 18.90 in)

• The Xerox 700 Digital Color Press will reproduce 11”x17” full bleed when printing on 12x18” or 13”x19” paper and A3 full bleed when printing on SRA3 paper. The maximum length images (480 mm) are only produced on media 19” long. On all media there is a Lead Edge deletion of 4mm and a Trail Edge deletion of 4mm. Side edge deletion is 3mm except for 13x19” media. On 13x19” media the side deletion is 3.5mm.

6


Warm-up Time* • 150 sec or less

• 30 sec or less

• After PowerOn or after SleepMode exit

• After LowPower mode exit**

First Print Out Time • 11.2 sec or less Color

• 7.5 sec or less B/W

• in Ready mode, FPOT is the time elapsed from when IOT receives Start command, until the trail edge of the first print exits the print engine.

Resolution • 2400 x 2400 x 1 dpi

• 2400 x 2400 x 1 dpi

• 600 x 600 x 1 dpi

• Print Engine

• Copy

• Print (Gray Font only)

Scanning Resolution • Up to 600 x 600 x 1 dpi • Several scan resolution settings are selectable via Xerox 700 Digital Color Press User Interface touch panel. Lower resolutions will result in files that are smaller in size and thereby reducing the customer's network traffic.

• See Scan section for details

Color Consistency • DeltaE = 7 • Within a page

Color to Color Registration

• ≤ 87 microns • The specification for color to color mis-registration is equal to or less than 87 microns, evaluated on either

• 1) Color Xpressions 90g/m2 uncoated paper or

• 2) Colotech+ 90g/m2 uncoated paper.

• Color to color mis-registration may vary outside of the specification when using heavyweight papers above 90g/m2.

Service Call Rate • At an average usage of 35,000 copies or prints per month on centerline paper, it is expected that service will be required about once every 5 weeks.

• Actual service call rate is influenced by total print volume, environmental conditions, area coverage, and media characteristics.

Shutdown Rate (power-off power-on)

• On average, less than 1 fault per day requiring a power-recycle to recover.

• Based on 35,000 AMPV, one 8-hour shift per day, using centerline papers.

Offsetting Catch Tray (Standard Output Device)

• 500 sheets • Represents capacity using Xerox Color Xpressions Plus or Xerox Colotech+ centerline paper.

* Status where paper feed can be started immediately when Start button is pressed.

** When M/C exits from Low Power mode after 1 hour from change to Low Power Mode.

7

Front to back registration on the Xerox 700 Digital Color Press is 1mm.

The following table contains more technical registration information regarding image registration, magnification, and skew specifications for the Xerox 700 Digital Color Press.

Note: These specifications only apply to Xerox 700 Digital Color Press centerline paper measured on an 11 x 17” sheet. Note: Environment (temperature, humidity), Type of Media, Media Cut, and part replacement may effect alignment adjustments. Note: The custom paper profiles tool (available through the UI) can be used to modify registration and skew settings for specific papers; please refer to the User Guide for specific directions.

Item Trays 1-3 OHCF 3

OHCF 3.2

HCF (A4 -8.5x11 1Tray HCF)

MSI (Bypass) Condition

Lead Registration ±0.7mm ±1.5 mm ±1.5 mm

Side Registration ±0.7 mm ±1.7 mm ±2.9 mm

Skew along the Lead Edge (200mm)

±0.5 mm ±1.5 mm ±1.5 mm

Skew along the Side Edge (400mm)

±1.0 mm ±3.0 mm ±3.0 mm

Side1-2 Perpendicularity (400mm)

±0.6 mm ±1.4 mm -

Parallelism (400mm) ±0.6 mm ±1.1 mm -

Image Loss • Lead Edge • Trail Edge • Side Edge

4.0 mm 4.0 mm 3.0 mm

- 100%

Side1-2 Registration (Lead Reg. direction)

1.0 mm －

Side1-2 Registration (Side Reg. direction)

1.0 mm －


Meters • Color Impressions

• Black Impressions

• Color Large Impressions

• Total Impressions

• The Digital Copier enables accurate billing of black and white and color copied pages.

8

Product Caveats/Limitations • The maximum print/copy speed for the system is determined by the process speed of the Xerox 700 Digital

Color Press engine; image quality adjustments are done frequently to maintain consistent IQ. • As a printer / copier, the Xerox 700 Digital Color Press is a document printer; therefore, in reverse order

(face-up) printing the print engine will not cycle up until the entire job is ready. This will impact First Print Out Time (FPOT). The printer may cycle down between each job depending on job complexity.

• When printing, overall system performance (‘Click to Clunk’ time) is primarily dependent upon the software applications and network environment being used. Rasterizing (RIP-ing) is only a small fraction of Click to Clunk time.

• Attempts to feed heavier than recommended paper stocks, and/or misuse of the media settings, may cause machine damage or poor image quality. Using media at run modes other than that recommended for the grade may cause poor image quality and serious machine damage.

• If the requested finishing setting is outside machine capabilities: – Copy jobs will be sent through unfinished – Print jobs from the Creo and EFI color servers will be sent through unfinished – Print jobs from the FreeFlow color server will be held

• 45-36x faults may occur intermittently. The expected frequency is approximately once every 20,000 prints or once a week, depending on print volume. To recover, power off and power on the printer.

• 127-211 / 311 faults may occur after jam clearance. To recover, Power Off/ Power On the printer. • System requirements messages (e.g., “Order Waste Toner Container”, “Hole Punch Waste Container Full”)

may occasionally be blocked by the current UI screen. Close the Job Status screen and open the Machine Status/Supplies screen to check consumable status.

• If the machine stops running mid-job, or does not begin printing after a job is submitted, check the Machine Status/Supplies screen to determine if supplies need to be replaced. The system will stop if sufficient supplies are not available for a submitted job. If the problem persists, check the Machine Status/Fault screen, select the fault, and click on the Instructions button.

• If the machine stops running mid-job, or does not begin printing after a job is submitted, verify that the applicable paper tray is not empty. The system will stop if sufficient media is not available for a submitted job. If the problem persists, check the Machine Status/Fault screen, select the fault, and click on the Instructions button.

• The system does not prohibit duplexing coated substrates from the internal trays (Trays 1-3); however, there can be a significant increase in jams or multi-feeds. If large quantities of coated paper are to be run, the OHCF is recommended for paper feeding.

• When using heavy coated 11’” x 17” stock, closing Trays 1-3 with too much force will result in a paper size misread. Open and close the tray gently to allow the paper sensors to correctly identify paper size.

• If the adjustment arms are disturbed while re-loading paper in Tray 5, the paper size setting will return to default and cause job to stop until the paper size setting is corrected by the user.

9

Media Selection Guidelines

The following paper types are recommended to ensure you receive the best image quality from your Xerox 700 Digital Color Press:

Media Type Xerox Equivalent

Uncoated paper

North America - Xerox Color Xpressions Plus (90 g/m2/24 lbs) Europe – Colotech+ (90 g/m2/24 lbs)


Coated paper

North America – Xerox Digital Color Elite Gloss 80# Text (120 g/m2) Europe – Xerox Digital Color Elite Gloss 80# Text (120 g/m2)


• Every effort has been made to ensure that the Xerox 700 Digital Color Press supports a broad range of media. Keep in mind, however, that using only Xerox-recommended media maximizes reliability and paper-handling performance.

• For further information and recommendations regarding media selection and handling, refer to the Material Usage Guide provided with your system and the Recommended Materials List (RML) available from your Xerox representative or at <http://www.xerox.com/downloads/usa/en/r/RML_700_DCP.pdf>.

• Typically, heavy weight papers exhibit increased variability of formation and surface smoothness, which may result in degraded image quality.

• Paper from all trays is printed topside first. It is recommended that Xerox branded paper be loaded with ream wrapper seam-side up.

• Manufacturers of coated stock do not recommend use of their media when the ambient relative humidity exceeds 60%. Relative humidity greater than 40% may increase multi-feeds from Trays 1, 2, 3 and 5.

• All paper stretches to a certain extent during printing. The amount of stretch is dependent on paper type and environmental conditions. Stretch is most noticeable on coated stocks. This stretch can affect front-to-back image registration. Use the Alignment Profiles feature described in the System Administration Guide for instructions on how to minimize this effect.

• Image registration, image quality (i.e. white spots), and machine reliability can be adversely affected when custom-cut paper is inaccurately cut, is of poor quality, or loose paper fibers are present on the cut edges.

• Image registration, image quality (i.e. white spots), jam frequency and machine reliability can be adversely affected when punched or drilled paper is of poor quality and/or loose hole plugs are present in the ream.

Media Support Documentation

Media support documentation includes:

• Recommended Materials Lists <http://www.xerox.com/downloads/usa/en/r/RML_700_DCP.pdf> • NA (North American) Customer Support / Escalation Process for media issues • Materials Usage Guide • The Paper Advantage Guide • DMO (Developing Marketing Organization) Media testing support • XE (Xerox Europe) Media testing support

These documents are available at http://www.xerox.com.

10

Print Engine Productivity Speeds- IPM (Impressions per Minute)

• Note: Productivity in these charts is based on images per minute (ipm), not prints per minute (ppm) • Note: Productivity in these charts applies to jobs run on a single media; switching trays within a job will

impact job productivity. • Unless otherwise specified, IPM numbers refer to simplex, duplex, color and BW prints or copies. Coated and Uncoated stock:

Paper Size

A4 LEF, B5 LEF

8.5” x 11”

LEF

A4 SEF, 8.5” x 11”

SEF

B4 SEF, 8.5” x 14”

SEF

A3 SEF 11” x 17”

SEF

13” x 19.2”

Internal Paper Trays (Trays 1-

3) and all HCFs

≤210 mm ≤216 mm ≤298 mm ≤365 mm ≤432 mm ≤488 mm

Uncoated

64-176 g/m2

• 71 • 70

• 51 Simplex

• 46 Duplex

• 39 • 35 • 31

177-220 g/m2 • 51 Simplex

• 46 Duplex

• 51 Simplex

• 46 Duplex

• 35 • 30 • 25 • 22

221-256 g/m2 ‡ • 51 • 51 • 35 • 30 • 25 • 22

257-300 g/m2 ‡ • 35 • 35 • 25 • 21 • 17 • 15

Coated

106-176 g/m2 • 51 Simplex

• 46 Duplex

• 51 Simplex

• 46 Duplex

• 35 • 30 • 25

• 22 Simplex

• 10.5 Duplex

177-220 g/m2 • 35 Simplex

• 31 Duplex

• 35 Simplex

• 31 Duplex

• 25 • 21 • 17 • 15

221-300 g/m2 ‡ • 35 • 35 • 25 • 21 • 17 • 15

*B5 not applicable

‡ does not apply to internal trays (Trays 1-3)

Transparencies and Tab Stock:

11

Paper Size

A4 LEF, B5 LEF

8.5” x 11”

LEF

A4 SEF, 8.5” x 11”

SEF

B4 SEF, 8.5” x 14”

SEF

A3 SEF 11” x 17”

SEF

13” x 19.2”

Internal Paper Trays (Trays 1-

3) and all HCFs

≤210 mm ≤216 mm ≤298 mm ≤365 mm ≤432 mm ≤488 mm

Transparency

B/W w/ Finisher

• 40* • 40 • 29 • NA • NA • NA

B/W w/o Finisher • 40* • 40 • 29 • NA • NA • NA

Full Color w/Finisher

• 18* • 18 • 13 • NA • NA • NA

Full Color w/o Finisher

• 9* • 9 • 8 • NA • NA • NA

Tab paper

106-176 g/m2 • 32 • 32 • NA • NA • NA • NA

177-256 g/m2 • 23 • 23 • NA • NA • NA • NA

257-300 g/m2‡ • 16 • 16 • NA • NA • NA • NA

*B5 not applicable

‡ does not apply to internal trays (Trays 1-3)

12

• Note: Productivity in these charts is based on images per minute (ipm), not prints per minute (ppm)

• Note: Productivity in these charts applies to jobs run on a single media; switching trays within a job will impact job productivity.

• Unless otherwise specified, IPM numbers refer to simplex, duplex, color and BW prints or copies.

Paper Size

A4 LEF, B5 LEF

8.5” x 11” LEF

A4 SEF 8.5” x 11”

SEF

B4 SEF 8.5” x 14”

SEF

A3 SEF 11” x 17”

SEF

13” x 19.2”Bypass (Tray 5)

≤210 mm ≤216 mm ≤298 mm ≤365 mm ≤432 mm ≤488 mm

Uncoated

64-176 g/m2 • 50 Simplex

• 45 Duplex

• 50 Simplex

• 45 Duplex

• 41 • 35 • 31 • 28

177-220 g/m2 • 40 Simplex

• 36 Duplex

• 40 Simplex

• 36 Duplex

• 32 • 27 • 24 • 22

221-256 g/m2 • 40 • 40 • 32 • 27 • 24 • 22

257-300 g/m2 • 25 • 25 • 19 • 17 • 15 • 14

Coated**

106-176 g/m2 * • 40 Simplex

• 36 Duplex

• 40 Simplex

• 36 Duplex

• 32 • 27 • 24 • 22

177-220 g/m2 • 25 • 25 • 19 • 17 • 15 • 14

221-300 g/m2 • 25 • 25 • 19 • 17 • 15 • 14

Transparency

B/W w/ Finisher

• 40 • 40 • 29 • NA • NA • NA

B/W w/o Finisher

• 40 • 40 • 29 • NA • NA • NA

Full Color w/Finisher

• 23 • 23 • 15 • NA • NA • NA

Full Color w/o Finisher

• 9 • 9 • 8 • NA • NA • NA

Tab paper

106-176 g/m2 • 32 • 32 • NA • NA • NA • NA

177-256 g/m2 • 23 • 23 • NA • NA • NA • NA

257-300 g/m2 • 16 • 16 • NA • NA • NA • NA

*running lightweight (less than 140 g/m2) coated stock through Tray 5 is not recommended

*environmental conditions may require that coated paper be fed one sheet at a time through Tray 5

13

Image Quality

With its low melt EA toner properties and higher print speed, the Xerox 700 Digital Color Press will produce output with a lower gloss level that is consistent with offset.

• As with any printing process, artifacts will occur. These include streaks, mottle, banding, spots, etc. For most jobs and clients, the expected level of artifacts is within the normal operational and component quality ranges of the system and will not affect the acceptability of the job. Maintenance procedures are available to mitigate these artifacts.

• Artifacts may occur with more frequency when running heavyweight coated media. • Artifact-sensitive jobs should be monitored. • Using products on the Recommended Materials List (RML) and maintaining your environment will also help

to minimize the occurrence of these artifacts. • Color quality perception is subjective and will be affected by ambient lighting conditions. • The appearance of the document displayed on the monitor screen may not match the output print because

the monitor uses RGB color space parameters. • The customer is responsible for calibrating the Xerox 700 Digital Color Press. • Image quality is strongly influenced by paper surface structure, texture, and color. To ensure that your

customers are optimally satisfied, key applications should be printed on the Xerox 700 Digital Color Press using representative paper and reviewed by the customer.

• The surface texture of some uncoated papers may cause increased graininess in halftone areas printed with only black toner. This effect may be minimized by adding process black and/or using smooth or coated papers (refer to the Recommended Materials List).

• Sheets of a job may exhibit slight gloss differential from page to page. Operational mode will have an impact on the ‘level’ of gloss differential.

• Prints may exhibit random white spots caused by paper dust, stray developer beads, or other miscellaneous particles. You can reduce the occurrence of white spots by using Xerox approved paper. If you are cutting your own paper, ensure that cut edges are dust free, and keep the machine in a clean and dust/dirt reduced environment. Failure to do this will result in increased frequency of white spots.

• To extend the life of your fuser, Xerox recommends the usage of multiple fusers. Multiple fusers provide maximum copy/print output for longer periods of time and ensure image defects and wear lines on output are avoided. Depending on the types of jobs run and their frequency, you may want more than one fuser available: – one fuser roll for smaller paper – one fuser for larger paper

Always refer to your User Guide for information and hints and tips on using your fuser to its maximum life capacity.

The Xerox 700 Digital Color Press is optimized for most media; specific media may result in curl which can be corrected using the internal de-curlers on the print engine and the optional Interface Module (IFM) and optional Light Production C Finisher.

14

Non-Standard paper sizes

The Xerox 700 Digital Color Press supports non-standard paper sizes. However, due to rounding and unit-conversions that occur in the client applications, print server, and printer, some mismatch may occur between the paper size entered at the application, and the paper size that must be entered at the printer. The operator may need to adjust the entered paper dimensions by up to 0.1 in (2.5 mm) in order for the printer to detect that the requested paper size has been loaded. In addition, the printer interprets some paper sizes included in the PPD as non-standard sizes.

Duplex Prints • The Duplexing Automatic Document Feeder (DADF) for hardcopy scanning will handle originals from 5.5 x

8.5” to 11 x 17” (or A3) in size, and from 16 to 28lb Bond in weight. The DADF has a maximum capacity of 250 sheets (based on 24lb Paper).

• Automatic duplexing can be done on all sizes of media, up to 80# Cover (220 g/m2). • Manual duplexing can be performed on media up to 110lb Cover (300 g/m2) or coated 100lb Cover (280

g/m2) from Tray 5 (Bypass). • Manual duplex can be performed on media up to 13x19" (SRA3 320mm x 450mm / Maximum 320mm x

482mm) from Tray 5 (Bypass). (Note: Image quality degradation is possible above 220 g/m2.) • As with any printer or copier, duplex performance is not expected to match the performance for single-

sided copying. Paper jam rates may be higher than the rate you will experience for the same throughput material in single sided mode.

Integrated Scanner • 250 sheet capacity (90 g/m2) • Originals up to 11 x 17 (A3) in weights from 38 gsm (16 lb bond) to 200 gsm (53 lb bond) • Duplex Automatic Document Feeder (DADF) • Scan resolution: 200 x 200, 300 x 300, 400 x 400, 600 x 600 dpi • Scan to FTP Scan speed by document size (simplex mode, using DADF)

Document Size

B/W Scanning

Speed

Color Scanning

Speed A4 LEF 81 51 A4 SEF 59 38 A3 SEF 49 28

8.5" x 11" LEF 80 50 8.5" x 11" SEF 62 40 8.5" x 14" SEF 49 32 11" x 17" SEF 48 27

15

Paper/Throughput

For more detailed information on throughput materials, please refer to the Xerox Materials Usage Guide and the Recommended Materials List.

Tray # Size Capacity (using 24lb / 90 g/m2

Paper)

Specified Weights

1-3 • Min: 5.5” x 8.5” SEF (139mm x 215.9mm SEF) (5.5” x 8.5” LEF cannot be run)

• Max: 13” x19.2”/SRA3 SEF

• 550 sheets • 64-220 g/m2 uncoated, 106-220 g/m2 coated. Higher jam rates (feed rates and multi-feeds) may occur on coated paper in trays 1-3

Tray 5 (Bypass)

• Min: 100mm x 148mm (3.9” x 5.8”) SEF

• Max: 13 x 19.2” /SRA3 SEF

• 250 sheets • 64-300 g/m2

uncoated, 106-300 g/m2 coated

Tray 6 1 tray OHCF (Option)

• B5 up to 13” x 19.2”/SRA3 • 2,000 sheets • 64-300 g/m2 uncoated, 106-300 g/m2 coated

Tray 6 & Tray 7 2 tray OHCF (Option)

• B5 up to 13” x 19.2”/SRA3 • 4,000 sheets • 64-300 g/m2

uncoated, 106-300 g/m2 coated

• Recommended paper to maximize image quality and product reliability is Xerox Color Xpressions Plus (90 g/m2/24 lbs) or Colotech+ (90 g/m2/24 lbs) (smooth bright white paper). This paper is specifically designed to maximize image quality and machine performance over a wide range of environmental conditions.

• Attempts to feed heavier than recommended paper stocks, and/or misuse of the media settings, may cause machine damage or poor image quality. Using media at run modes other than that recommended for the grade may cause poor image quality and serious machine damage.

• Note: There is no Tray # 4 on the Xerox 700 Digital Color Press. • All paper trays can be reloaded while jobs are running from any other tray. It is not possible to change

paper settings while jobs are running.

16

Transparencies

The Xerox 700 Digital Color Press will feed 8.5 in x 11 in/A4 transparencies at a speed of 23 ppm color. Use Xerox removable stripe transparency material (USA and Canada: 3R3028, 3R3108; Xerox Europe: 3R98199, 3R3108 ) for optimum system performance and image projection. These premium transparencies are specifically designed to provide optimum copy quality. Use of other transparencies may cause machine damage and result in excessive service calls.

Due to the increased thickness of the removable stripe, no more than (100) 3R3108 transparencies should be loaded in a paper tray at one time. The maximum output stack height should not exceed 100 transparencies.

Envelopes

The Xerox 700 Digital Color currently supports running the following European and Asian envelopes through Tray 5:

Envelope Type Feed Direction Envelope Size (mm)

Envelope: Chou-kei3* SEF 120.0×235.0

Envelope: Kaku-ga** SEF 240.0x332.0

Envelope C4 SEF 229.0×324.0

Envelope C5 SEF 162.0×229.0

*opening/flap on the envelope's short dimension; accepts A4 folded in thirds

** opening/flap on the envelope's short dimension; accepts A4 flat, A3 folded in half

Envelopes must be placed with the opened flap set as trail edge.

17

Recommended Supplies

Supply

Description

Reorder Number

Cartridges per Carton

Yield Projection at representative

total area coverage

(using centerline paper)

Dry Ink: *

WW Metered

Toner Reorder Number

WH/ XE Sold Toner

Reorder Number

DMO Sold Toner

Reorder Number

30% (7.5%

per color)

Black 6R1375 6R1383 6R1379 1 20k per cartridge***

Cyan 6R1376 6R1384 6R1380 1 22k

Yellow 6R1378 6R1386 6R1382 1 22k

Magenta 6R1377 6R1385 6R1381 1 21k

Drum Cartridge**:

Black 13R642 1 373k at 100%Black/White 354k at 100% Color

Cyan 13R643 1 156k

Yellow 13R643 1 156k

Magenta 13R643 1 156k

Toner Waste Bottle*

8R12990 Contact the Welcome Center for replacement

1 33k

Charge Corotron

13R637 1 175k

Fuser Module 8R13065 1 200k

Convenience and Advance Staple Cartridge

8R12964

1

5,000 staples

Convenience and Advance Staple Refills

8R12941 8R12941 8R12941 3 staple refills (5,000 staples each)

Light Production C Finisher Staples


Booklet Maker Staple Refill


All Booklet makers (Professional and Light Production C) use this Staple Refill

* The dry ink yield projections are based on the indicated area coverage at standardized conditions on 8.5 in x 11 in/A4 Xerox 700 Digital Color Press centerline paper. Please note that actual yields vary greatly depending on color intensity, area coverage, paper stock, and mode selected.

18

NEMA 6-15R

** Drum Cartridge replacement frequency noted above for 8.5 in x 11 in/A4 images when using Xerox 700 Digital Color Press centerline paper and other stocks with equivalent smoothness, cut quality and structure. Replacement rates may be more frequent for operations which use high percentages of coated stocks, have area coverage greater than 70% of each color, and/or larger than 8.5 in x 11 in/A4 size throughputs, e.g., 11 in x 17 in/A3.

*** One black cartridge per carton; two black cartridges are used in tandem, with a resulting yield of 40k.

Initial Supplies • Each Xerox 700 Digital Color Press is delivered with an initial supply of Toner as well as the CRUs (Drum

Cartridges, Charge Corotron, Fuser, and Waste Toner Container as well as Staples – included for finishing options with stapling).

• To order additional Supply (toner / staples) or Throughput materials, contact the Xerox Supplies Marketing Center : – 1-800-822-2200 US, 1-800-668-0199 CAN (English), 1-800-668-0133 CAN (French.) – US Customers on Metered Price Plans should call the Metered Hotline, U.S. 1–800–599-2198 to acquire

additional toner.

Environmental and Electrical Requirements

Electrical Requirements: Area Power Voltage (V) Frequency (Hz)

XC 208-240V-10%/+6% 50/60+/-3%

XE 220-240V+/-10% 50/60+/-3%

US Specific Power (Xerox 700 Digital Color Press): Xerox 700 Digital Color Press Product Code: MAV

Voltage (sole use circuit recommended) 220 VAC 208-240 VAC

Amperage Circuit 15

Cycles 60 Hz Single Phase (two wires plus ground)

Power Consumption 12 amps / 2200 VA (watts)

Power Cord Length 8’ 2”

Receptacle NEMA 6-15R, 15A-250V

A single power cord (US receptacle diagram shown at left) is required for the Xerox 700 Digital Color Press.

19

Optional Feeders and Finishers: With the exception of the HCF, Advanced Finisher and Professional Finisher, each optional feeding and finishing device requires an additional 100-240VAC country-specific power receptacle.

US Specific Power (Optional Feeders and Finishers): With the exception of the HCF, Advanced Finisher and Professional Finisher, each optional feeding and finishing device requires an additional 100-240VAC country-specific power receptacle.

Optional Accessories Power and Circuit Requirements

Input or Output Device

Product Code Current / Run Power Voltage (VAC) North America (NA)

OHCF 1 Tray AKC 3 Amps / 60 Watts (NA) 100-127 100-240

OHCF 2 Tray MFA 5 Amp/ 65 Watts (NA) 100-127 100-240

Light Production C Finisher

MLA

2 Amps / 70 Watts (NA) 100-127 100-240

Light Production C Finisher w/ Booklet Maker

MGA 2 Amps / 70 Watts (NA) 100-127 100-240

GBC AdvancedPunch

UAD (NA) UAE (XE)

2.8 Amps/310 Watts (NA) 1.3 Amps/300Watts (XE)

(NA) 100-127 100-240

SquareFold Trim Module

TLX (NA) 100-127 100-240

Interface Module MFB 2.5 Amps / 85 Watts (NA) 100-127 100-240

High Capacity Stacker

MAY 1.5 Amps / 70 Watts (NA) 100-127 100-240

FreeFlow Print Server

MDB

6.9 Amps / 520 Watts

(NA) 100-127 100-240

FreeFlow Monitor N/A 1.2 Amps (NA) 120

FreeFlow Print Server Professional Package (spectro)

N/A .3 Amps (NA) 120

EFI Fiery Print Server

MXT

6 Amps / 200 Watts

(NA) 100-127 100-240

EFI Monitor GKB 1.2 Amps (NA) 100-127

Creo Print Server MXA 2.25 Amps/150 Watts NA) 100-127 200-240

Creo Monitor N/A .8 Amps (NA) 100-127

Convenience Stapler

N/A 2.1 Amps (NA) 100-127

15A-125V NEMA 5-15R

20A-125V NEMA 5-20R

20

Input and Print Server Devices

To determine Amp circuit requirements for accessories, add Amps from Current / Run Power column above:

1. Add Amps of each device. 2. If total amps are 12 or below, a 15 amp circuit may be used with NEMA 5-15R; however, a 20 amp circuit is

recommended using NEMA 5-20R receptacles. 3. If total amps are 12.1 through 16, a 20 amp circuit is required. 4. Total number of receptacles required is determined by total number of accessories.

Example 1:

2-tray OHCF (5 amps) + Light Production C Finisher (2 amps) + Interface Module (2.5 amps) = 9.5 amps.

• A 15 amp circuit may be use with 3 receptacles (NEMA 5-15R) for each device.

Example 2:

2-tray OHCF (5 amps) + Light Production C Finisher (2 amps) + Interface Module (2.5 amps) + FreeFlow Server (6.9 amps) + Monitor (1.2 amps) + FreeFlow Professional Package (.3 amps) = 17.9 amps.

This configuration requires 2 circuits:

• A 20 amp circuit is required for 2-tray OHCF and Server/Monitor/Prof Package with 4 (NEMA 5-20R) receptacles and a 15 amp circuit for Finisher and the Interface Module using 2 (NEMA 5-15R) receptacles.

Recommended Wall Receptacle Placement for Xerox 700 Digital Color Press and accessories (US receptacles shown):

It is recommended that receptacles be grouped as shown in relation to the Xerox 700 Digital Color Press.

Finishing Devices 700 Digital Color Press

21

Installation Considerations • Ground Fault Protection is provided which meets Xerox internal safety requirements and exceeds the

Industry Standards for Information Technology Equipment. • Physical delivery of Xerox 700 Digital Color Press will be by a Xerox authorized “D/R” carrier. The carrier will

install and perform a functional check of the printer/copier unit. The carrier will review the software/documentation with the customer. For the printer / copier the customer is responsible for connecting and configuring the equipment on their network.

• With the exception of the HCF, Advanced Finisher and Professional Finisher, each optional feeding and finishing device requires an additional 100-240VAC country-specific power receptacle.

• The unit weighs 583 lbs. (265 kg) - Printer, Scanner, and DADF. The Light Production Finisher with booklet maker, interposer and folder is 392 lbs. (178 kg).

• Power cords for the feeders, finishers and print engine are 8’ 2” (2490mm) long. • Power cords for the Print Servers are approximately 7.5 feet (2.3 meters). • The outbound Print Server video cables measure approximately 16.4 feet (5 meters). • One network drop is required for installation as a printer / copier. • There should be a minimum of 78 inches (1,981 mm) clearance from the floor to the nearest overhead

obstruction. • The service area (including device dimensions) from front to back is always 102” (2591 mm). • Electrical requirements and space requirements must be satisfied before the equipment is delivered.

Environmental Requirements

Environmental Minimum Maximum

Temperature 50º F (10º C) 82º F (28º C)

Humidity (non-condensing) 15% RH 85% RH

Better performance is achieved when conditions are maintained between 20-25°C (68-77 °F) and 45-55% RH*.

Heat Emission Approximately 716 BTU/Hr (Standby)

50 Hz - 4067 BTU/Hr (Running) 60 Hz – 4232 BTU/Hr (Running)

Noise Emission 55 dBA (Standby) 78 dBA (Running)

Power Consumption ≅5.7 watts* (Sleep Mode) 2.2 kVA** (Continuous Running)

Altitude (above sea level) 0 ft (0 meters) 8,200 ft. (2,500 meters)

Low Power Mode Power Usage 143 watts ≤300 Watts

Low Power Mode Recovery Time - 30 seconds

Sleep Mode - ≤95 Watts

*Manufacturers of coated stock do not recommend use of their media when the ambient relative humidity exceeds 60%

**Stated as an average. Warm up power consumption is 1,600 VA

22

Moveable and Stationary Installations

• The following configurations can be moved by one person, and can therefore be considered moveable: o A Xerox 700 Digital Color Press system consisting of the print engine and the offset catch tray o A Xerox 700 Digital Color Press system consisting of the print engine and the Advanced

Finisher o A Xerox 700 Digital Color Press system consisting of the print engine and the Professional

Finisher o A Xerox 700 Digital Color Press system consisting of the print engine, Interface Module and

Light Production C Finisher o A Xerox 700 Digital Color Press system consisting of the print engine, Interface Module and

High Capacity Stacker • Larger systems must be considered stationary due to the amount of force required to move the

system. • Carpeted flooring surfaces require the installation of a mobility plate. • Mobility plates are available from your Sales Representative.

23

Space Requirements • All standard Xerox space requirements apply to this installation including overhead, shared, aisle or hallway,

and operator space. • There should be a minimum of 78 inches (1,981 mm) clearance from the floor to the nearest overhead

obstruction. • To enable a Xerox Service Representative to safely repair the system, the work area must measure at least

36 “(91.44 cm) square around the print server. • The service area (including device dimensions) from front to back is always 102” (2591 mm). • The dimensions listed below provide the overall service space required, including the space to the nearest

obstruction. The dimensions reflect both typical and hallway installations and are absolute minimums.

Please note: These dimensions do not include space required for the Print Server. Refer to the print server CED for space requirements.

Service/Operational Space Moveable Installation Stationary Installation

A Rear of Processor / System 10 ” * 254 mm**

30 ” 762 mm

B Front of main Processor 42 ” 1067 mm

42 ” 1067 mm

C Front of HCF and Finisher / Folder

38 ” 965 mm

38 ” 965 mm

D1 Left Side of System 13” 330 mm

13” 330 mm

D2 Right side of System Finisher

24” 610 mm

24” 610 mm

E Allowable Height 78 ” 1981 mm

78 ” 1981 mm

Service Envelope: Width = Dimensions + D1 + D2, Depth = 102” (2591 mm) * Moveable installations can run with 10” (254 mm) between the rear of the system and a wall, but still require 102” total service area depth.

FINISHER IOT FEEDER D2D1

A

CB

24

Physical Dimensions

The following table shows the overall physical dimensions of each module of the Xerox 700 Digital Color Press, including space between the modules when connected into a system.

Module Width inches (mm)

Depth inches (mm)

Height inches (mm)

Weight lbs (kg)

IOT/FFM 30 (762) 30 (762) 56 (1,423) 661 ( 300)

Bypass Tray (fully extended)

22 (559) 30(762) 56 (1423) NA

HCF 22 (559) 30(762) 56 (1423) 64 (29)

OHCF 41(1016) 30 (762) 56(1423) 1-tray :265 (120) 2-tray : 419 (190)

Advanced Finisher 39 (991) 30 (762) 56(1423) 121 (54.88)

Professional Finisher 39 (991) 30 (762) 56(1423) 190 (86.2)

IFM 13.5 (343) 30 (762) 56(1423) 110 ( 50)

HCS 31.5 (800) 30 (762) 56(1423) 251 (114) Light Production C Finisher with Booklet Maker (without optional Folder)

44 (1118) 30 (762) 56(1423) 298 (135)

Light Production C Finisher (with Booklet Maker and optional Folder)

52 (1321) 30 (762) 56(1423) 386 (175.1)

SquareFold Trimmer Module

50 (1270) 30 (762) 56(1423) 209 (95)

GBC AdvancedPunch

12 (305) 30 (762) 56(1423) 154 (69)

25

Dimensions for Several Configurations of the Xerox 700 Digital Color Press:

Configuration Width* Depth Height Weight

30 in. 30 in. 56 in. 661 lbs Digital Press

762 mm 762 mm 1423 mm 300 kg

46 in. 30 in. 56 in. 674 lbs Digital Press + Offset Catch Tray (OCT) 1168 mm 762 mm 1423 mm 306 kg

52 in. 30 in. 56 in. 661 lbs Bypass Tray + Digital Press

1320.8 mm 762 mm 1423 mm 300 kg

68 in. 30 in. 56 in. 674 lbs Bypass Tray + Digital Press + OCT 1727 mm 762 mm 1423 mm 306 kg

68 in. 30 in. 56 in. 738 lbs Bypass Tray + High Capacity Feeder (HCF) + Digital Press + OCT 1727 mm 762 mm 1423 mm 333 kg

91 in. 30 in. 56 in. 782/(851) lbs Bypass Tray + Digital Press + Advanced/ Professional Finisher 2311.4 mm 762 mm 1423 mm 355/(386) kg

91 in. 30 in. 56 in. 846/(915) lbs Bypass Tray + HCF + Digital Press + Advanced/Professional Finisher 2311.4 mm 762 mm 1423 mm 384/(415) kg

110 in. 30 in. 56 in. 1047/(1115.5) lbs

1-drawer Oversized High Capacity Feeder (OHCF) + Digital Press + Advanced/ Professional Finisher 2794 mm 762 mm 1423 mm 475/(506) kg

110 in. 30 in. 56 in. 1201/(127) lbs 2-drawer Oversized High Capacity Feeder (OHCF) + Digital Press + Advanced/ Professional Finisher

2794 mm 762 mm 1423 mm 545/(576) kg

117 in. 30 in. 56 in. 1221 lbs Bypass Tray + HCF+ Digital Press + Interface Module + Light Production C Finisher (with Booklet Maker) + C/Z Folder

2972 mm 762 mm 1423 mm 554 kg

136 in. 30 in. 56 in. 1421 lbs 1-drawer OHCF + Digital Press + Interface Module + Light Production C Finisher (with Booklet Maker) + C/Z Folder 2946.4 mm 762 mm 1423 mm 654 kg

136 in. 30 in. 56 in. 1421 lbs 1-drawer OHCF + Digital Press + Interface Module + Light Production C Finisher (with Booklet Maker) + C/Z Folder 3454 mm 762 mm 1423 mm 664 kg

26

Configuration Width* Depth Height Weight

136 in. 30 in. 56 in. 1576 lbs 2-drawer OHCF + Digital Press + Interface Module + Light Production C Finisher (with Booklet Maker) + C/Z Folder

3454 mm 762 mm 1423 mm 715 kg

116 in. 30 in. 56 in. 1287 lbs 1-drawer OHCF + Digital Press + Interface Module + High Capacity Stacker (HCS) 2946.4 mm 762 mm 1423 mm 584 kg

116 in. 30 in. 56 in. 1441 lbs 2-drawer OHCF + Digital Press + Interface Module + High Capacity Stacker (HCS) 2946.4 mm 762 mm 1423 mm 654 kg

Standard Configuration Features

The Xerox 700 Digital Color Press is delivered with:

• Print Engine with Scanner • Duplexing Automatic Document Feeder (DADF) • Controller connectivity enabled • Electronic Pre-Collation (EPC) • 1,900 sheet paper capacity via 3 paper trays and bypass tray.

Optional Accessories

Accessory Description

High Capacity Feeder

2,000 sheet capacity ( based on 80 g/m2centerline paper)

1 Tray Oversize High Capacity Feeder

2,000 Sheet* (up to 13x19.2/SRA3) capacity from 64-300 g/m2 (uncoated) and 106-300 g/m2 (coated).

2 Tray Oversize High Capacity Feeder

4,000 Sheet* (up to 13x19.2/SRA3) capacity from 64-300 g/m2 (uncoated) and 106-300 g/m2 (coated).

Interface Module

The Interface Module aligns the paper paths of the engine and finisher, cools and decurls paper exiting the printer, and allows communication between the engine and finisher. One Interface Module is required on systems with optional Light Production C Finisher and/or High Capacity Stacker.

Advanced Finisher 500 sheet top tray, 3,000 sheet stacker tray

Professional Finisher 500 sheet top tray, 1,500 sheet stacker tray, Up to 20 set booklet tray

27

GBC AdvancedPunch

The GBC AdvancedPunch is an inline die punch that utilizes modular die sets to enable a variety of hole-punch patterns in A4/8 ½ x 11 in (LTR) long-edge-fed media. LTR die punch ships with 19-hole die set A4 die punch ships with 21-hole die set

Light Production C Finisher

The Light Production C Finisher includes a basic in-line punch, stapler, the stacker tray and top exit tray. It also includes a built-in decurler unit that corrects the curl on paper output from the print engine, and a built-in interposer that feeds cover paper to finisher for saddle-staple operation.

Light Production C Finisher with Booklet maker

The Light Production C Finisher with booklet unit includes a basic in-line punch, stapler, the stacker tray and top exit tray, and a booklet unit capable of saddle stapling and bi fold. It also includes a built-in decurler unit that corrects the curl on paper output from the print engine, and a built-in interposer that feeds cover paper to finisher for saddle-staple operation.

C/Z Folder

An optional Folder unit that can handle Z-fold, Tri-C, and Tri-Z, it can be added to the Light Production C Finisher or the Light Production C Finisher with Booklet maker The C/Z folding tray can accommodate up to 40 sheets of 24 lb (90 g/m2) media). Supported Paper sizes are 8.5x11” (A4) Allows C/Z folding of media up to 24 lb (90 g/m2) uncoated.

SquareFold® Trimmer

An optional piece of equipment that attaches the Light Production C Finisher with Booklet Maker (with or without the C-Z Folder) SquareFold® Trimmer flattens the spine of the booklet to make it lay flat and trims the face of the booklet.

High Capacity Stacker

Stack up to 5,000 sheets* offsetting output stack tray with movable cart to move to off line finishing. Additional cart is available for customer to order. 500 sheet* top tray, 64 g/m2- 300 g/m2, up to 13 x 19.2 in (330x488mm) Sample Set – 1.) Programmable at Color Server or 2.) On-Demand at HCS User Interface‡

Foreign Interface Kit

Enables the connection of external devices such as auditrons or coin-op devices. This will perform in copy and print modes.

Convenience Stapler Staple up to 50 sheets of 90 g/m2 / 24 lb. media.

*based on 80 g/m2 centerline paper

‡ at launch this feature is available only with the FreeFlow server. Creo and EFI servers will offer this capability post-launch.

28

Combination of Output Functions and Destinations

Finisher Top Tray

Stack Tray Staple Hole

Punch Booklet Bi-fold (Single Fold)

Interposer C-Z Fold

Advanced Finisher o o o o

Professional Finisher o o o o o o

Light Production C Finisher (LPC Finisher)

o o o o o

LPC Finisher w/C-Z fold o o o o o o

LPC Finisher w/ Booklet Maker o o o o o o o

LPC Finisher w/ Booklet Maker and C-Z fold

o o o o o o o o

High Capacity Stacker o o

Optional High Capacity Feeder (HCF) • 2,000 sheet capacity (80 g/m2centerline paper) • 220 mm(0.87 in) stack height • Powered by print engine – no external power source required • Maximum paper size 8.5 x 11 in./A4 • Weight range: 52-216 g/m2 (uncoated)

29

Optional Oversized High Capacity Feeder (OHCF)

• 1 or 2 tray OHCF (each tray requires a fan kit) • Handles coated substrates up to 220 g/m2 for auto duplex • Air-assisted, robust feeder design for oversized and heavyweight • 2,000 sheet capacity (80 g/m2 centerline paper) • Maximum paper size 13 x 19.2 in./SRA3 • Weight range: from 64-300 g/m2 (uncoated) and 106-300 g/m2 (coated) • Maximum auto duplex up to 220 g/m2 /80 lb. cover, coated and uncoated • Requires an additional electrical receptacle (see Electrical Requirements section).

Product Specifications (OHCF)

Oversized High Capacity Feeder Module Capacity: 1 tray, 2,000* sheets Minimum Paper Weight: 64 g/m2 uncoated or 106 g/m2 coated Maximum Paper Weight: 300 g/m2 coated or uncoated Minimum Paper Size: 182mm x 210mm (7.2” x 8.3”) Maximum Paper Size: 330mm x 488mm (13” x 19.2”) Maximum Auto Duplex: 220 g/m2 80-lb cover (coated and uncoated) Oversized High Capacity Feeder 2-Tray Module (shown with UI) Capacity: 2 trays, 4,000* sheets (each tray capacity 2,000* sheets) Minimum Paper Weight: 64 g/m2 uncoated or 106 g/m2 coated Maximum Paper Weight: 300 g/m2 coated or uncoated Minimum Paper Size: 182mm x 210mm (7.2” x 8.3”) Maximum Paper Size: 330mm x 488mm (13” x 19.2”) Maximum Auto Duplex: 220 g/m2 80 lb cover (coated and uncoated) * (80 g/m2 centerline paper)

30

Advanced Finisher • 500 sheet top tray, 3,000 sheet stacker tray • paper side registration ±6mm • staple paper stack height 5.7 mm (0.22 in) • 50-sheet, multi-position stapling • The Advanced Finisher offers Hole Punch as a standard feature. • Hole punch capacity is equal to the regular capacity of the chosen output tray. For the

US, 2- and 3-hole punching is available; for Europe, 2- and 4- hole punch is available. Stacks can be punched on the left or right side, or on the top edge. If hole punching fails, check to make sure that the punch waste container is empty before calling for service.

• Powered by print engine – no external power source required • 52-216 g/m2 uncoated stock to all trays • 217-280 g/m2 uncoated stock to top tray only

Professional Finisher • 500 sheet top tray, 1,500 sheet stacker tray • paper side registration ±6mm • staple paper stack height 5.7 mm (0.22 in) • 50-sheet, multi-position stapling • The Professional Finisher offers Hole Punch as a standard feature. • Hole punch capacity is equal to the regular capacity of the chosen output tray. For the

US, 2- and 3-hole punching is available; for Europe, 2- and 4-hole punch is available. Stacks can be punched on the left or right side, or on the top edge.If hole punching fails, check to make sure that the punch waste container is empty before calling for service.

• Powered by print engine – no external power source required • 52-216 g/m2 uncoated stock to all trays • 217-280 g/m2 uncoated stock to top tray only • Up to 20 set booklet tray:

– Stapled: 15 sheets/set (up to 90 g/m2 uncoated stock) – Non-stapled: 5 sheets/set – Bi-Fold (Single Fold): 1 sheet/set, up to 169 g/m2 uncoated stock – Stackable number of sets depends on paper size

31

Optional High Capacity Stacker (HCS) The HCS is designed for long production runs.

• Up to 5,000 sheets offsetting output stack tray with movable cart to move to off- line finishing. Additional cart is available for customer to order.

• Sample Set – 1.) Programmable at Color Server or 2.) On-Demand at HCS User Interface.

• Requires an additional electrical receptacle (see Electrical Requirements section). • Combined finishing (attaching a HCS and Light Production C Finisher together in

a system) is available with external Print Servers only. • Attaching a HCS and Light Production C Finisher together in a system with the

Integrated Print Server will result in all jobs being sent unfinished to the top tray of the HCS until the second finisher is detached from the system, and the system is rebooted.

HCS Top Tray

HCS Top Tray Capacity

Stack height 500 sheets

paper weight <=80 g/m2

min: 100 x 148 mm

max: 13 x 19.2 (in) 330 x 488 (mm)

stack weight: 70 Kg (154 lb)

HCS Stack Tray Stack Tray Capacity by weight and paper finish

Paper Size

203 x 182 (mm) A4 B4 A3 SRA3

330 x 488 (mm)

Paper weight and finish

8 x 7.16 (in)

8.5 x 11 (in)

8.5 x 14 (in)

11 x 17 (in)

12 x 18 (in)

13 x 19.2 (in)

Uncoated

52-80 g/m2

Sheet Qty 5,000 5,000 5,000 5,000 5,000 5,000 5,000

81-300 g/m2

Stack Height

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

Coated

105-300 g/m2

Stack Height

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

570mm (22.44” )

32

Optional Interface Module (IFM)

• The Interface Module aligns the paper paths of the engine and finisher, cools and decurls paper exiting the printer, and allows communication between the engine and finisher.

• One Interface Module is required on systems with optional Light Production C Finisher and/or High Capacity Stacker.

• Requires an additional electrical receptacle (see Electrical Requirements section).

Optional Light Production C Finisher (shown with Optional Booklet Maker)

This section provides the details and expectations for the optional Light Production C Finisher that will be installed with your Xerox 700 Digital Color Press.

The Light Production C Finisher is an output device that can process the following: 100-sheet stapling, 3,000 sheets stacking, punch, saddle stapling/center-fold, optional Z-fold/three-fold, and cover paper insertion.

The Light Production C Finisher has a built-in decurler unit that corrects the curl on paper output from IOT, a built-in stapler with staple-pin cut function, and a built-in interposer that feeds cover paper to finisher for saddle-staple operation.

The Light Production C Finisher with optional booklet unit (shown in photo) includes the punch and stapler, the stacker tray and top exit tray, and a booklet unit capable of saddle stapling and bi -fold.

The Light Production C Finisher requires an additional electrical receptacle (see Electrical Requirements section).

33

Light Production C Finisher Product Specifications

Light Production C Finisher Top Tray Capacity Top Tray Capacity by weight and paper finish

Paper Size

100 x 148

(mm) A4 B4 A3 SRA3

330 x 488

(mm)

Paper weight

8.5 x 11 (in)

8.5 x 14 (in)

11 x 17 (in)

12 x 18 (in)

13 x 19.2 (in)

Uncoated

52 - 80 g/m2 Stack Height/Sheet Qty

67mm (2.64”)

500 sheets

500 sheets

500 sheets

500 sheets

500 sheets

500 sheets

80-300 g/m2 Stack Height 67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

Coated

105-80 g/m2 Stack Height 67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

177-280 g/m2

Stack Height 67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

67mm (2.64”)

Light Production C Finisher Stack Tray Capacity

Number of Sheets by weight and paper finish

Paper Size

182 x 257

(mm)

A4 B4 A3 SRA3*


8.5 x 11 (in)

8.5 x 14 (in)

11 x 17 (in)

12 x 18 (in)*

13 x 19.2 (in)*

Uncoated

52-80 g/m2

Sheet Qty 1,500 3,000 1,500 1,500 1,500 1,500 1,500

81-300 g/m2

Stack Height

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

Coated

105-280 g/m2

Stack Height

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

180mm (7.09 in)

*Cannot be offset

34

Light Production C Finisher Bi-Fold (Single Fold) Capability (available on Optional Booklet Maker)*

Bi-Fold (Single Fold) **Capability by weight, size and paper finish

A4 B4 A3 SRA3

Paper weight and finish 8.5 x 11

(in) 8.5 x 14

(in) 11 x 17

(in) 12 x 18 (in)

Uncoated 60-300 g/m2 1 1 1 1 1

Coated 105-300 g/m2 1 1 1 1 1

*Copy mode: 300 gsm coated and uncoated, image must be outside fold.

Print mode: 300 gsm uncoated (face-up).

**Bi-Fold (Single Fold): 1 sheet/set, 60-300g/m2 uncoated stock, 105-300 g/m2 coated stock

Fold accuracy (lead and side edge): ≤2.5 mm

Optional C/Z Folder for the Light Production C Finisher

An optional Folder unit that can handle Z-fold, Tri-C, and Tri-Z, it can be added to the Light Production C Finisher.

• The C/Z folding tray can accommodate 30 sheets of up to 24 lb (90 g/m2) uncoated media. • Supported Paper size is 8.5x11” (A4) to the bottom tray, 11 x 17” (A3) to the top tray • Fold accuracy as shown below: Z-Fold

Envelope C-Fold

±1.5 mm ±1.0mm

2 mm±2mm

1/2Paper

±1.5 mm ±1.5 mm 8 mm

2 mm

36

Interposer for the Light Production C Finisher • The Light Production C Finisher includes a standard Interposer, used to insert pre-printed stock into finished sets without

having to go through the engine. Labels, coated media & envelopes are not supported.

Tray Capacity by weight, size and paper finish

Paper Size

B5 A4 B4 A3 Paper weight and finish 8.5 x 11 (in) 8.5 x 14 (in) 11 x 17 (in)

Uncoated

60-80 g/m2 Sheet Qty 200 shts 200 shts 200 shts 200 shts

81-220 g/m2

Stack Height 22mm (0.87 in) 22mm (0.87 in) 22mm (0.87 in) 22mm (0.87 in)

Hole Punching Capability for the Light Production C Finisher

The Light Production C Finisher offers Hole Punch as a standard feature.

• Hole punching is not available to the Booklet Tray. • Because hole punching occurs as individual sheets pass through the hole punch, capacity is equal to the

regular capacity of the chosen output tray. • For the US, 2- and 3-hole punching is available; for Europe, 2- and 4- hole punch is available. Stacks can be

punched on the left or right side, or on the top edge.

Hole Punching Capability by weight and paper finish

Paper Size

B5 A4 B4 A3 Paper weight and finish 8.5 x 11 (in) 8.5 x 14 (in) 11 x 17 (in)

Uncoated 52-200 g/m2 Applicable Applicable Applicable Applicable

Coated 105-200 g/m2 Applicable Applicable Applicable Applicable

37

Staple Capabilities by weight and paper finish for the Light Production C Finisher

Staple Capabilities by weight and paper finish

Paper Size

Smallest size A4 B4 A3

Paper weight and finish 203.2x254

(mm) 8.5 x 11 (in) 8.5 x 14 (in) 11 x 17 (in)

52-80 g/m2 100 100 100 100

81-90 g/m2 up to 100 up to 100 up to 100 up to 100

91-105 g/m2 50 50 50 50

106-128 g/m2 30 30 30 30

129-150 g/m2 19 19 19 19

151-176 g/m2 12 12 12 12

177-220 g/m2 5 5 5 5

221-256 g/m2 4 4 4 4

Uncoated

256-300 g/m2 3 3 3 3

106-128 g/m2 5 5 5 5

129-150 g/m2 5 5 5 5

151-176 g/m2 5 5 5 5

177-220 g/m2 5 5 5 5

221-256 g/m2 4 4 4 4

Coated

256-300 g/m2 3 3 3 3

38

Optional Booklet Maker for the Light Production C Finisher* Sheets per Booklet by weight, size and paper finish

Paper Size


A4 8.5 x 11

(in)

B4 8.5 x 14

(in)

A3 11 x 17

(in)

12 x 18

(in)

SRA3

60-80 g/m2 25 25 25 25 25

81-90 g/m2 20 20 20 20 20

91-105 g/m2 10 10 10 10 10

106-128 g/m2 10 10 10 10 10

129-150 g/m2 10 10 10 10 10

151-176 g/m2 10 10 10 10 10

177-220 g/m2 5 5 5 5 5

221-256 g/m2 4 4 4 4 4

Uncoated

256-300 g/m2 3 3 3 3 3

106-128 g/m2 10 10 10 10 10

129-150 g/m2 10 10 10 10 10

151-176 g/m2 10 10 10 10 10

Coated

177-220 g/m2 5 5 5 5 5

*Unavailable in Copy Mode

Fold accuracy of the inner sheet (lead and side edge):

• Stapled: ≤1.5 mm for A4 sheets, ≤2.0 mm for other sizes • Non-stapled: ≤1.5 mm • Stapled: 25 sheets/set • Non-stapled: 5 sheets/set

39

Light Production C Finisher Product Caveats/Limitations • If the compiler tamper arm resets itself during a job, the job will need to be re-submitted • If hole punching fails, check to make sure that the punch waste container is empty before calling service • After cancelling a job sent to the Booklet maker, empty the purge tray (located inside the Light Production

C Finisher) before submitting another print job. This will ensure that purged sheets are not inadvertently inserted into the next booklet printed.

• Combined finishing (attaching a HCS and Light Production C Finisher together in a system) is available with external Print Servers only.

• Attaching a HCS and Light Production C Finisher together in a system with the Integrated Print Server will result in all jobs being sent unfinished to the top tray of the HCS until the second finisher is detached from the system, and the system is rebooted. This will require a service call.

• A reduction in productivity may be experienced when sending duplexed 11” x 17” stock to the stacker tray. • The machine will pause for xerographic adjustment when necessary. This will impact productivity. • Requires an additional electrical receptacle (see Electrical Requirements section).

40

GBC Advanced Punch

The GBC AdvancedPunch is an inline die punch that utilizes modular die sets to enable a variety of hole-punch patterns in A4/8 ½ x 11 in (LTR) long-edge-fed media.

• For use with HCS or Light Production C Finisher – not available for use on Advanced or Professional Finishers, or with the Offset Catch Tray

• The GBC Advanced Punch can be added to an existing Light Production C Finisher or HCS through an available upgrade kit

• The GBC Advanced Punch requires an Interface Module (IFM) with updated software and hardware • Supported by all color servers • Supports media from 80 to 216 gm2, coated and uncoated

• ProClick die supports media from 80 to 203 gm2 • Able to bypass all coated and uncoated media sizes printed on the Xerox 700 Digital Color Printer • A4 and LTR punch units are not the same; therefore, A4 and LTR die sets are not interchangeable.

– The LTR punch unit will be shipped with the 19-hole punch die. – The A4 unit will ship with the 21-hole punch die. – Additional punch dies are available for order (see below)

Punch Dies

The GBC Advanced Punch is capable of punching a variety of hole-punch patterns by simply changing the punch die. Punch dies can be changed in seconds without tools. The punch dies currently available are listed below.

A4 and Letter version die sets are not interchangeable.

LTR Version Dies A4 Version Dies

3-hole 2-hole

VeloBind 4-hole

19-hole PB VeloBind

W2 Square 20-hole PB

W3 Square 21-hole PB

ProClick W2 Round

C4 W2 Square

W3 Round

W3 Square

ProClick

C4

Please note: Punch die life will be increased if the wick material is lightly oiled every 50K punch cycles

(approximately every month) with quality machine oil such as 3-in-I Oil. Small deposits of oil will be observed

around the perimeter of the punched holes until the excess oil is absorbed (usually within 50 sheets).

42

SquareFold® Trimmer Module

Overview

The SquareFold® Trimmer Module is an optional piece of equipment that flattens the spine of the booklet to make it lay flat and trims the face of the booklet. It requires the Light Production C Finisher with Booklet Maker (with or without the C-Z Folder) that has upgraded software and hardware. The SquareFold® Trimmer Module is a fully-integrated device, controlled through the print engine UI.

The SquareFold® Trimmer Module is supported by all color servers.

The SquareFold® Trimmer Module can be added to an existing Light Production C Finisher through an available upgrade kit.

Configuration

The SquareFold® Trimmer Module is located after the Light Production C Finisher and performs as follows:

• receives the booklet from the booklet unit • transports the received booklet to the square fold unit to flatten the spine of the booklet and then to the

trimmer unit to trim the face of the booklet • deposits the finished booklet to the booklet tray. • The SquareFold® Trimmer Module is also able to face-trim without square-folding • All output from the Light Production C Finisher can be passed through, square-folded, trimmed, or both

squared-folded and trimmed

Auto Recognition of SquareFold® Trimmer Module

When the SquareFold® Trimmer Module is docked to the Light Production C Finisher via cable, the finisher automatically recognizes that the SquareFold® Trimmer Module is installed.

• Square-folding feature: flattens the spine (stapled side) of the booklet. • Trimming feature: trims the face of the saddle-stapled or bi-folded (single-folded) sheets of paper.

43

Combination of Output Functions and Destinations

O: Can be combined x: Cannot be combined

Functions Output Destination

Book

let

Trim

mer

Squa

re F

old

Book

let T

ray

Trim

mer

Boo

klet

Tr

ay

Offset X X X X X

Staple X X X X X

Punch X X X X X

Interposer O O O O O

Booklet - O O* O O

Z-Fold X X X X X

C- Fold X X X X X

Func

tion

Bi-Fold (Single Fold) - O O* O O

Staple + Punch X X X X X

Staple + Z-Fold X X X X X

Staple + Interposer X X X X X

Punch + Z-Fold X X X X X

Z-Fold + Interposer X X X X X

Staple + Punch + Z-Fold X X X X X

Func

tion

+ Fu

nctio

n

Staple + Punch + Z-Fold + Interposer

X X X X X

* Square-folding/trimming of non-stapled sets and square-folding of 4 or less sheets in a set are outside the specification and are therefore not guaranteed (jams may occur frequently or wrinkles may occur on the square-folded side of paper).

44

Combining High Capacity Stacker and the Light Production C Finisher

The Xerox 700 Digital Color Press will allow installation of both a High Capacity Stacker and a Light Production

C Finisher in a single system. It will not be possible to install 2 High Capacity Stackers on the Xerox 700 Digital

Color Press.

An upgrade kit will be required to add the second finisher to existing installations.

The High Capacity Stacker and the Light Production C Finisher can be installed at the same time on any system

using any of the available external Print Servers:

• Xerox FreeFlow Print Server for the Xerox 700 • Xerox CX Print Server, Powered by Creo for the Xerox 700 • Xerox EX Print Server, Powered by Fiery for the Xerox 700 (with or without EFI Splash RPX-iii Color Workflow

Software)

Please note: The High Capacity Stacker and the Light Production C Finisher cannot be installed at the same time

on any system using the Integrated Fiery Color Server. If both finishers are detected, the following error

message will be printed to the top tray of the HCS:

The Xerox 700 Digital Color Press with Integrated Fiery Color Server does not support the current configuration of installable options. The High Capacity Stacker and the Light Production C Finisher cannot be installed at the same time. Please contact your Xerox representative for further information.

All jobs will be sent unfinished to the top tray of the HCS until the second finisher is detached from the system,

and the system is rebooted. This will require a service call.

45

Supported Configurations

The following sketches show the supported configurations for the Xerox 700 Digital Color Press:

IOT IFM

Light Production C Finisher with Booklet Maker, with or without C-Z Fold

1- or 2- Tray OHCF SquareFold® Trimmer Module

Configuration 1

IOT

IFM HCS1- or 2- Tray OHCF

Light Production C Finisher with or without Booklet Maker, with or without C-Z Fold

Configuration 2 Not available with Integrated Fiery Color Server

IOT IFM HCS



1- or 2- Tray OHCF

Configuration 3 Not available with Integrated Fiery Color Server

46

IOT IFM HCS1- or 2- Tray OHCF

GBC Advanced Punch

Configuration 4

IOT IFM

1- or 2 Tray OHCF

GBC Advanced

Punch

Light Production C Finisher with or without Booklet Maker, with or without C-Z Fold

Configuration 5

IOT IFM

1- or 2 Tray OHCF

GBC Advanced

Punch


Configuration 6

SquareFold®Trimmer Module

47

IOT IFM HCS



1- or 2 Tray OHCF

GBC Advanced

Punch

Configuration 8 Not available with Not available with Integrated Fiery Color Server

IOT

IFM HCS

Light Production C Finisher with or without Booklet Maker, with or without C-Z Fold 1- or 2 Tray

OHCF GBC

Advanced Punch

Configuration 7 Not available with Not available with Integrated Fiery Color Server

48

Customer Agreement

Reference Material

Xerox 700 Digital Color Press is shipped with a complete set of user guides on a CD ROM.

Customer Support

The Xerox Customer Support Centers are available to provide general information, answer questions and take service calls.

You can reach the Customer Support Center at the following phone numbers:

• United States: 1-800-821-2797 (toll-free) • Canada :1-800-939-3769 (toll-free) • Xerox Europe (Local Numbers):

• (AT) Austria 01 207 9000 • (BE) Belgium Dutch: 02 713 14 53 • French: 02 713 1452 • (DK) Denmark 7010 7288 • (FI) Finland 09 6937 9666 • (FR) France 0825 012 013 • (DE) Germany 0180 500 4392 • (IT) Italy 199 112 088 • (JP) Japan +81 3 5352 7620

• (NL) Netherlands 020 656 3620 • (NO) Norway 815 00 308 • (ES) Spain 902 160 236 • (SE) Sweden 0771 17 88 08 • (CH) Switzerland French: 043 299 9001 • German: 043 299 9000 • Italian: 043 299 9002 • (GB) United Kingdom 0870 900 55

To order Replacement Customer Replaceable Units (CRUs):

• Full Service Maintenance customers order replacement CRU’s through Xerox Customer Support Center using the toll free numbers above.

• Time and Materials Maintenance customer order replacement CRU’s through the Logistics Customer Support Center at 1-800-828-5881.

To order additional Supply (toner / staples) or Throughput materials:

• The Xerox Supplies Marketing Center, 1-800-822-2200 US, 1-800-668-0199 CAN (English), 1-800-668-0133 CAN (French) is available for ordering Xerox supplies, including paper and other throughput material.

• US Customers on Metered Price Plans should call the Metered Hotline, U.S. 1–800–599-2198 to acquire additional toner.

49

Customer Training

Customer training on machine features and functions is a purchasable service for the Xerox 700 Digital Color Press.

Responsibility Matrix:

Action Customer Xerox

Communicate the need for adequate space and power to accommodate the Xerox 700 Digital Color Press and accessories.

X

Provide adequate space and power to configure the Xerox 700 Digital Color Press. X

Unpack system / components X

Install system hardware X

Connect all System Components prior to powering up the system X

Install the printer description files and server, status Desktop Accessories on Client (Printer only) X

Ensure network configuration (Printer only) X

Confirm network integrity (Printer only) X

Acquire and install client workstation network software (Printer only) X

Run initial software diagnostics when directed X

Monitor and adjust as required X

Load any additional fonts (Printer only) X

Order and replace Customer Replaceable Units (Drum cartridges, Fuser and Waste Toner Cartridge) as needed. X

Provide Help Line support (with purchase of FSMA) X

Provide spared parts (with purchase of FSMA) X

Provide service (with purchase of FSMA) X

Return failed or expended parts and cartridges X X

50

Customer Expectations Agreement

Check off the modules that will be part of this install and for which expectations have been set:

_____ Xerox 700 Digital Color Press _____ Optional High Capacity Feeder

_____ Optional Oversized High Capacity Feeder (1-or 2- Tray)

_____ Optional Interface Module (IFM)

_____ Optional Advanced Finisher _____ Optional Professional Finisher with Booklet Maker

_____ Optional Light Production C Finisher (LPC Finisher)

_____ Optional Light Production C Finisher (LPC Finisher) with Booklet Make

_____ Optional CZ Folder (CZ Folder) _____ Optional High Capacity Stacker (HCS)

_____ Xerox FreeFlow Print Server for the Xerox 700

_____ Xerox CX Print Server, Powered by Creo for the Xerox 700

_____ Xerox EX Print Server, Powered by Fiery for the Xerox 700

_____ Integrated Fiery Color Server

_____ EFI Splash RPX-iii Color Workflow Software (Requires passing data through the Xerox EX Print Server or Integrated Fiery Color Server

Please note: A separate CED must be filled out and signed for the print server.

Primary Customer Applications:

Special considerations or performance limitations identified by Xerox and agreed to by the customer:

Upending and/or Stair Climbing Required and Reviewed:

Yes Not Required

I have reviewed and understand the product specifications for each of the modules that will be installed: (signatures required)

Customer

Xerox Sales Representative

Xerox Analyst Representative

Xerox Service Representative

I have viewed a representative output sample from the Xerox ____________ Press and the image quality is acceptable for the needs of my organization: (Signature required if Xerox Digital Press with order.)

Customer

52

Th i s pag e i n ten t i ona l l y le f t b la nk

xerox 700 dcp customer expectations document - rev.3.3

Documents

document version

digital color press

product specifications

product caveatslimitations

united states andor

united states of america

optimum product performance

software programs